y-450=03jis b 2002 screwed: jis b 0203 flanged: jis b 2220 jv8-1 scs13a/cf8 non-asbestos — ball...

Y-450=03

1307①ITP

2

Notes 1) Refer to individual specification sheet or the drawing for the details of a product. 2) Main units of this catalog are shown in SI (MPa, °C, millimeter). 3) Refer to the attached P-T ratings about applicable pressure and temperature. 4) The non-asbestos product is used for the gland packing and gasket of stainless steel valves as a manufacturer’s

standard.

Products guarantee Term of a guarantee: Within one year after the date of delivery from our factory to the original customer. Contents of a guarantee: If the installations and the service conditions (such as pressure, temperature, fluid, etc.) are proper, necessary replacement and repair of our product will be carried out without charge. Guarantee exceptions: Please keep in mind that the above articles of guarantee will not apply to the case owing to the following reasons: 1) Non-compliance of the customer with the technical instructions furnished by our catalog and specification sheet. 2) Natural disaster incidents, such as a fire, flood damage, an earthquake, and falling stone. 3) Reconstruction or repair by any third party other than us. 4) Deterioration. (such as shot rust, degradation, chemical changes, etc.) 5) Any other matter resulting from the damage not being regarded as manufacturer’s responsibility.

In addition, you will be required necessary charge for repair or exchange of parts on failure or damage by the guarantee exceptions. Please contact our sales staff or agency for the details.

The specification and the performance term of our product indicated in this catalog are based on the internationally governed standards and specifications, our products experience or the design calculation and our in-house examination.

When using the product beyond the service conditions mentioned in this catalog, users are required to consult our sales staff or agency for further advice in advance, or to conduct the verification or evaluation for the performance under users’ responsibility. We shall not be liable for any damages resulting from lack of aforementioned procedures by the customer.

* Don’t use our products in flammable or toxic gas service. * Items mentioned in this catalog are subject to change without prior notice to the customers.

3

Design Specification

Series Class P-T ratings F-F dimension End connections Shell thickness Body material Gland packing Gasket

U-S

erie

s

Gate Globe Check

10K Manufacturers standard 180°C max. oil, gas, air, water-1.0MPa

Screwed: JV8-1

Flanged: JIS B 2002

Screwed: JIS B 0203

Flanged: JIS B 2220

JV8-1 SCS13A/CF8 Non-asbestos —

Ball 800 Manufacturers standard 38°C oil, gas, air, water-5.5MPa Saturated steam 1.0MPa

JIS B 0203Manufacturers

standardSCS13A/CF8

SCS14A/CF8M

PTFE/ FKM “O”-ring

PTFE

Ball 600Manufacturers standard 38°C oil, gas, air, water-4.10MPa Saturated steam 1.0MPa

PTFE —

Strainer

Screwed: 20K

Fanged: 10K

180°C max. oil, air, water- 1.0MPaJV8-2

JV8-2

Screwed: JIS B 0203 Flanged:

JIS B 2220

JV8-2 SCS13A/CF8 — R-PTFE

VN-S

erie

s

Gate Globe Check

10K JIS B 2220 Note: 1 ASME B16.10 JIS B 2220 ASME B16.34 SCS13A/CF8 Non-asbestos Non-asbestos

V-S

erie

s

Gate Globe Check

(swing, lift) Strainer

　　　Note: 3

10K JIS B 2220 Note: 1

ASME B16.10 (Except strainers)

JIS B 2220

ASME B16.34SCS13A/CF8

SCS14A/CF8MNon-asbestos

Non-asbestos (Joint sheet)

20K Non-asbestos (Spiral wound)

150 ASME B16.34 Note: 1 ASME B16.5

Non-asbestos (Joint sheet)

300 Non-asbestos (Spiral wound)

Dua

l Pla

te C

heck

Val

ves

Rubber seat NBR

EPDM FKM

10K with

By-pass valve

NBR seat: 80°C max. oil, air, water-1.0MPa JV8-1

JV8-1 (Except 40 & 350mm API 594)

Wafer type JIS B 2220

JV8-1

SCS13

Non-asbestos for bypass

valve—

20K with

By-pass valve

NBR seat: 80°C max. oil, air, water-2.0MPa JV8-1

Metal seat

10K

ASME B16.34 API 600

— —20K

150 Wafer type ASME B16.5

— —300

Scr

ewed

Ball 10K

JV8-1

Manufacturers standard

JIS B 0203

ASME B16.34

SCS13A/CF8 PTFEPTFE seats

Flan

ged

Ball

10K JIS B 2002 JV8-1

JIS B 2220 SCS13 SCS13A/CF8

SCS14 SCS14A/CF8M

PTFE20K

R-PTFE/PFA Copolymer seats

150 ASME B16.34 ASME B16.10 ASME B16.15

300

But

terfl

y Va

lves

High perform-

ance

(PTFE seat)

20K10K

38°C max. water, oil, gas-2.0MPa JIS B 2002 Series 46

Wafer type JIS B 2220 (10K, 20K)

ASME B16.15 (125, 150)

JV9 JV8-1

SCS13A/CF8 Non-asbestos —

Notes: 1) Although the pressure-temperature ratings for the valve body of V-series and VN-series are mentioned in the above table, the highest working temperature of the

standard packing, made of non-asbestos, is 260°C max. However, since it is necessary to consider separately about type of gland packing and gasket depending on operating conditions (fluid, pressure, and temperature), please consult our sales staff or agency for details.

2) The standard gasket of 10K and Class 150 V-series gate, globe and check (swing, lift) valves is non-asbestos sheet. Moreover, ceramic filled PTFE is available upon request.

3) The standard gasket of Strainer is ceramic filled PTFE.4) Do not use our products in flammable or toxic gas service.

（）

4

U-Series Stainless Steel Valves

Design Manufacturers StandardType Gate Valves Globe ValvesClass 10K

JV8-1 Based on JV8-1 JV8-1

Fig. 802 802J 800 800J 830Size L H D1 L H D1 L H D1 L H D1 L H D1

8 (mm) 1/4" 44 68 55 10 3/8" 48 68 55 55 110 70

15 1/2" 54 97 70 85 100 70 52 68 55 85 112 70 65 113 7020 3/4" 58 102 70 95 106 70 60 94 70 95 113 70 80 114 7025 1" 65 112 80 100 116 80 72 101 70 110 143 100 90 144 100

32 11/4" 74 123 80 110 128 80 80 124 90 130 152 100 105 151 10040 11/2" 78 150 100 125 170 100 90 138 90 150 172 110 120 172 11050 2" 87 167 100 140 188 100 100 153 100 180 190 125 140 190 125

MaterialBody SCS13A SCS13A SCS13A SCS13A SCS13AStem SUS304 SUS304 SUS304 SUS304 SUS304Disc SCS13A SCS13A SUS304 SUS304 PTFE

Service conditions See P-T rating on page 12

Remarks PTFE seat

Design Manufacturers StandardType Globe Valves Swing Check Valves StrainersClass 10K

JV8-1 Based on JV8-1 JV8-1

Fig. 830J 804 804J 809 809JSize L H D1 L H L H L H L H

8 (mm) 1/4"10 3/8"15 1/2" 85 113 70 65 45 85 45 85 60 120 5820 3/4" 95 114 70 80 55 95 55 100 65 130 6625 1" 110 144 100 90 61 110 61 115 77 150 78

32 11/4" 130 151 100 105 71 130 71 135 90 170 9340 11/2" 150 172 110 120 72 150 72 150 100 190 10450 2" 180 190 125 140 81 180 81 180 115 220 122

MaterialBody SCS13A Body SCS13A Body SCS13AStem SUS304 Pin SUS304 Screen SUS304Disc PTFE Disc SCS13A


Remarks PTFE seat 40 meshes screen

D1

H

L

D1

L L

L L

L L

H

H H

H Hd

H

D1D1

5


Design Manufacturers StandardType Ball ValvesClass 600 800

Reduced bore Reduced bore Reduced bore Reduced bore Std. bore

Fig. 3550 3550W 4550A 4550W 4580Size d L H D1 d L H D1 d L H D1 d L H D1 d L H D1

8 (mm) 1/4" 4.5 39 31 60 4.5 39 25 39 4.5 39 31 60 4.5 39 25 39 10 3/8" 6.8 44 36 70 6.8 44 29 40 6.8 44 36 70 6.8 44 29 40

15 1/2" 9.2 56.5 41 85 9.2 56.5 35 55 9.2 56.5 41 85 9.2 56.5 35 55 10 60 50 100 20 3/4" 12.5 59 44 85 12.5 59 39 55 12.5 59 44 85 12.5 59 39 55 15 70 55 100 25 1" 16.0 71 48 100 16.0 71 48 100 20 80 60 130

32 11/4" 20.0 78 54 100 20.0 78 54 100 25 95 64 130 40 11/2" 24.5 83 65 125 24.5 83 65 125 32 108 73 150 50 2" 32.0 100 72 125 32.0 100 72 125 38 124 79 150

Material

Body SCS13A SCS13A SCS14A SCS14A SCS14AStem SUS304 or SUS316 SUS304 or SUS316 SUS316 SUS316 SUS316 / Chrome platedBall SUS304 or SUS316 SUS304 or SUS316 SUS316 SUS316 SUS316Seat R-PTFE R-PTFE R-PTFE R-PTFE R-PTFE


Remarks

Design Manufacturers StandardType Ball ValvesClass 800 10K

Std. bore Full bore Full bore

Fig. 3380 4760A 3060Size d L H D1 d L H D1 d L H D1

8 (mm) 1/4"10 3/8" 10 62 71 130

15 1/2" 10 60 69 100 15 67 55 100 15 65 102 130 20 3/4" 15 70 72 100 20 74 60 130 20 80 105 130 25 1" 20 80 77 120 25 89 63 130 25 90 124 160

32 11/4" 25 90 90 130 32 106 72 150 32 110 130 160 40 11/2" 32 100 95 130 38 118 78 150 40 120 115 230 50 2" 40 120 103 150 50 129 105 200 50 140 120 230

Material

Body SCS13A SCS14A SCS13AStem SUS304 / Chrome plated SUS316 / Chrome plated SUS304Ball SUS304 SUS316 SUS304 or SCS13ASeat R-PTFE R-PTFE PTFE


Remarks

D1

H

L

D1

L L

L L

L L

H

H H

H Hd

H

D1D1

6

High Performance Double Off-Set Butterfly Valves HIGH FLOW®-T Series

(mm)

Size d L H1 H2 H3 H4 L1 S D1Actuator

No.

50 50 43 88 170 206

45 42155 110

W1165 65 46 101 188 224

80 79 46 108 195 231

100 99 52 120 207 243 W12

125 126 56 145 235 271 W2

150 148 56 167 252 288 160 160 W20

200 190 60 189 275 321 57 67 178 200

W3

250 239 68 232 325 371 W40

300 288 78 262 351 401 68 90 260 300 W5

Standard Specification Type HIGH FLOW®-T (PTFE)

Fig. 581 (20K) size 50mm through 200mm

580 (10K) size 250mm and 300mm

Mating flangeJIS 10K/20K, ASME 125/150

BS 4504 PN10/16, DIN PN10/16

End-to-end dimension JIS B2002 series 46 / ISO 5752 Basic Series 20

Pressure –Temperature Rating JPI-7S-83, API 609, JV-9 Class 150 (See page 12)

Maximum service pressure2.0 MPa

Reverse pressure (pressure from stem side): 1.0 MPa

Flow direction Disc side to Stem side *1

Body type Wafer type

Service temperature –29°C~232°C

Material

Body SCS13A

Disc SCS13A

Stem SUS304

Seat ring PTFE / R-PTFE

Gland packing Flexible Graphite with PTFE

Actuator type worm gear, air cylinder, motor

Applicable media Steam*2, emissions gas*3, air, industrial water, food, oil, powder*4, grain*4

Remarks: *1. Regardless flow pressure, Disc side should be pressurized in the normal direction of the flow. *2. Permissible, but please consult our sales staff or distributor for steam application. *3. Don’t use our products in flammable or toxic gas service. *4. For some media, this valve cannot be used depending on some operating condition.

Fig. 580-G (10K, SCS13A body, PTFE seat) Sizes: 250mm and 300mm.Fig. 581-G (20K, SCS13A body, PTFE seat) Sizes: 50mm through 200mm.

H3

H2

H1

L

d

H4

L1

S

D1

FLOW

7

Flanged Ball Valves

Design Manufacturers StandardType Ball ValvesClass 10K 150

JV8-1

Fig. 3011L(SCS13A) / 4011L(SCS14A) 3131L 4131LSize d L H D1 d L H D1 H D1 d L H D1 H D1

15(mm) 1/2" 15 108 81 130 15 108 102 130 15 108 102 130 20 3/4" 20 117 84 130 20 117 105 130 20 117 105 130 25 1" 25 127 93 160 25 127 124 160 25 127 124 160

32 11/4" 32 140 97 160 40 11/2" 40 165 113 230 40 165 115 230 40 165 115 230 50 2" 50 178 120 230 50 178 120 230 50 178 120 230

65 21/2" 65 190 150 400 65 190 155 400 65 190 155 400 80 3" 80 203 161 400 80 203 165 400 80 203 165 400

100 4" 100 229 189 460 100 229 200 460 (3131G) 100 229 200 460 (Gear: 4131G)125 5" 125 356 209 460 125 356 220 460 312 310 125 356 220 460 467 310 150 6" 150 394 262 980 150 394 295 1000 337 310 150 394 295 1000 492 310 200 8" 200 457 317 1970 200 457 355 1500 414 360 200 457 355 1500 594 360

250 10" 250 533 477 500 250 533 727 500

Material

Body SCS13A / SCS14A CF8 SCS14A / CF8MStem SUS304 / SUS316 F304 SUS316 / F316Ball SCS13 / SCS14 F304 or CF8 SUS316 or SCS14A / F316 or CF8MSeat R-PTFE R-PTFE / PFA Copolymer R-PTFE / PFA Copolymer


Remarks Full bore

Design Manufacturers StandardType Ball ValvesClass 20K /300

Fig. 3331L(20K) / 3231L(300) 4331L(20K) / 4231L(300)

Size d L H D1 d L H D1

15(mm) 1/2" 14 140 108 130 14 140 108 130 20 3/4" 19 152 111 130 19 152 111 130 25 1" 24 165 124 130 24 165 124 160

32 11/4" 32 178 128 160 32 178 128 160 40 11/2" 38 190 134 230 38 190 134 230 50 2" 50 216 143 230 50 216 143 230

65 21/2" 64 241 179 400 64 241 179 400 80 3" 76 283 189 400 76 283 189 400

100 4" 100 305 251 750 100 305 251 750

125 5" 123 381 267 750 123 381 267 750 150 6" 151 403 315 1000 151 403 315 1000200 8" 202 502 406 1500 202 502 406 1500

Material

Body SCS13A / CF8 SCS14A / CF8MStem SUS304 / F304 SUS316 / F316Ball SUS304 or SCS13A / F304 or CF8 SUS316 or SCS14A / F316 or CF8MSeat R-PTFE / PFA Copolymer R-PTFE / PFA Copolymer


Remarks Full bore

D1

H

L

D1

L

H

dd

8

V-Series / VN-Series Stainless Steel Valves

Design Manufacturers StandardType Gate ValvesClass 10K 10K / 150 20K / 300

Fig. 803J (JV8-1) 803 (150) 853J (10K) (JV8-1) / 853 (150) 813J (20K) (JV8-1) / 813 (300) 863J (20K) (JV8-1) / 863 (300)

Size L H D1 L H D1 L H D1 L H D1 L H D1

15(mm) 1/2" 108 221 100 108 214 100 108 214 100 140 216 100 140 216 100 20 3/4" 117 227 100 117 214 100 117 214 100 152 225 100 152 225 100 25 1" 127 243 100 127 227 100 127 227 100 165 250 140 165 250 140

32 11/4" 140 276 140 140 257 140 140*1 257*1 140*1 178*2 300*2 160*2 178 292 160 40 11/2" 165 296 140 165 264 140 165 264 140 190 308 160 190 308 160 50 2" 178 339 180 178 308 160 178 308 160 216 333 200 216 333 200

65 21/2" 190 380 180 190 357 180 190 357 180 241 378 200 241 378 200 80 3" 203 441 200 203 417 200 203 417 200 283 433 250 283 433 250

100 4" 229 518 230 229 508 224 229 508 224 305 537 300 305 537 300

125 5" 254 627 250 254 619 280 254 619 280 381 658 355 381 658 355 150 6" 267 719 250 267 728 300 267 728 300 403 754 400 403 754 400 200 8" 292 927 300 292 923 355 292 923 355 419 944 450 419 944 450

250 10" 330 1124 360 330 1117 400 330 1117 400 457 1270 560 457 1270 560 300 12" 356 1317 450 356 1317 450 502 1438 600 502 1438 600

MaterialBody SCS13A SCS13A / CF8 SCS14A / CF8M SCS13A / CF8 SCS14A / CF8MStem SUS304 SUS304 / F304 SUS316 / F316 SUS304 / F304 SUS316 / F316Disc SCS13A SCS13A / CF8 SCS14A / CF8M SCS13A / CF8 SCS14A / CF8M

Service conditions 10K/20K: See P-T rating for JIS flanged valves on page 13 Class 150/300: See P-T rating for ASME flanged valves on page 13

Remarks *1 Fig: 853J only *2 Fig: 813J only

Design Manufacturers StandardType Globe ValvesClass 10K 10K / 150 20K / 300

Fig. 801J (JV8-1) 801 (150) 851J (10K) (JV8-1) / 851 (150) 811J (20K) (JV8-1) / 811 (300) 861J (20K) (JV8-1) / 861 (300)

Size L H D1 L H D1 L H D1 L H D1 L H D1

15(mm) 1/2" 108 198 100 108 176 100 108 176 100 152 181 100 152 181 10020 3/4" 117 198 100 117 178 100 117 178 100 178 208 140 178 208 14025 1" 127 198 100 127 180 100 127 180 100 203 208 140 203 208 140

32 11/4" 140 223 140 140 206 140 140*1 206*1 140*1 216*2 237*2 160*2 216 237 160 40 11/2" 165 223 140 165 206 140 165 206 140 229 237 160 229 237 160 50 2" 203 259 160 203 237 160 203 237 160 267 285 180 267 285 180

65 21/2" 216 290 180 216 280 180 216 280 180 292 328 224 292 328 224 80 3" 241 324 200 241 321 200 241 321 200 318 370 250 318 370 250

100 4" 292 367 250 292 365 250 292 365 250 356 445 355 356 445 355

125 5" 356 443 300 356 414 250 356 414 250 400 495 400 400 495 400 150 6" 406 487 300 406 488 355 406 488 355 444 554 450 444 554 450 200 8" 495 610 360 495 610 450 495 610 450 559 630 450 559 630 450

MaterialBody SCS13A / CF8 SCS13A / CF8 SCS14A / CF8M SCS13A / CF8 SCS14A / CF8MStem SUS304 / F304 SUS304 / F304 SUS316 / F316 SUS304 / F304 SUS316 / F316Disc SUS304 or SCS13A / F304 or CF8 SUS304 or SCS13A / F304 or CF8 SUS316 or SCS14A / F316 or CF8M SUS304 or SCS13A / F304 or CF8 SUS316 or SCS14A / F316 or CF8M


Remarks *1 Fig: 851J only *2 Fig: 811J only

LL

D1

H

D1

HL

LH

H

9


Design Manufacturers StandardType Globe with PTFE seat Swing Check ValvesClass 10K 10K 10K / 150 20K / 300

JV8-1

Fig. 831J (SCS13A) / 881J (SCS14A) 805J (JV8-1) 805 (150) 855J (10K) (JV8-1) / 855 (150) 815J (20K) (JV8-1) / 815 (300) 865J (20K) (JV8-1) / 865 (300)

Size L H D1 L H L H L H L H L H 15(mm) 1/2" 108 176 100

20 3/4" 117 178 100 25 1" 127 180 100

32 11/4" 140 211 140 40 11/2" 165 211 140 165 129 165 117 165 117 241 162 241 162 50 2" 203 237 160 203 129 203 117 203 117 267 167 267 167

65 21/2" 216 280 180 216 145 216 138 216 138 292 175 292 175 80 3" 241 321 200 241 152 241 144 241 144 318 180 318 180

100 4" 292 365 250 292 172 292 165 292 165 356 214 356 214

125 5" 356 414 250 330 198 330 186 330 186 400 235 400 235 150 6" 406 488 355 356 270 356 233 356 233 444 278 444 278 200 8" 495 610 450 495 309 495 290 495 290 533 325 533 325

250 10" 622 356 622 327 622 327 622 395 622 395 300 12" 698 392 698 392 711 494 711 494

MaterialBody Body SCS13A / SCS14A SCS13A / CF8 SCS13A / CF8 SCS14A / CF8M SCS13A / CF8 SCS14A / CF8MPin Stem SUS304 / SUS316 SUS304 / F304 SUS304 / F304 SUS316 / F316 SUS304 / F304 SUS316 / F316Disc Disc PTFE SUS304 or SCS13A / F304 or CF8 SUS304 or SCS13A / F304 or CF8 SUS316 or SCS14A / F316 or CF8M SUS304 or SCS13A / F304 or CF8 SUS316 or SCS14A / F316 or CF8M


Remarks

Design Manufacturers StandardType Lift Check ValvesClass 10K / 150 20K / 300

Fig. 824J (10K) (JV8-1) / 824 (150) 874J (20K) (JV8-1) / 874 (300) 834J (20K) (JV8-1) / 834 (300) 884J (20K) (JV8-1) / 884 (300)

Size L H L H L H L H 15(mm) 1/2" 108 64 108 64 152 73 152 73

20 3/4" 117 66 117 66 178 84 178 84 25 1" 127 67 127 67 203 84 203 84

32 11/4" 140 82 140 82 216 103 216 103 40 11/2" 165 82 165 82 229 103 229 10350 2" 203 95 203 95

MaterialBody SCS13A / CF8 SCS14A / CF8M SCS13A / CF8 SCS14A / CF8MDisc SUS304 or SCS13A / F304 or CF8 SUS316 or SCS14A / F316 or CF8M SUS304 or SCS13A / F304 or CF8 SUS316 or SCS14A / F316 or CF8M


Remarks

LL

D1

H

D1

HL

LH

H

10

Dual Plate Check Valves Strainers

Design Manufacturers StandardType Dual Plate Check ValvesClass 10K 20K 10K / 150 20K / 300

Fig. 806 816 806M (10K) / 806MW (150) 816M (20K) / 816MW (300)

Size L H D1 L H D1 L D L D 40(mm) 11/2" 54 118 63 54 118 63 60 86

50 2" 60 126 63 60 126 63 60 101 60 101

65 21/2" 67 134 63 67 134 63 67 121 67 121 80 3" 73 138 63 73 138 63 73 131 73 137

100 4" 73 151 63 73 151 63 73 156 73 162

125 5" 86 174 70 86 174 70 86 187 86 197 150 6" 98 188 70 98 188 70 98 217 98 235 200 8" 127 215 70 127 215 70 127 267 127 279

250 10" 146 254 80 146 254 80 146 330 148 353 300 12" 181 282 80 181 282 80 181 375 181 403 350 14" 184 420 222 447

400 16" 191 483 232 507 450 18" 203 538 264 572 500 20" 219 593 292 627

MaterialBody SCS13 SCS13 SCS13 / CF8 SCS13 / CF8Plate SCS13 SCS13 SCS13 / CF8 SCS13 / CF8Seat NBR NBR 304 (Matal) 304 (Matal)


Remarks SCS14 / CF8M body available upon request Metal seated, without bypass valve

Design Manufacturers StandardType StrainersClass 10K / 150

Fig. 807J (10K) (JV8-1) / 807 (150) 857J (10K) (JV8-1) / 857 (150)

Size L H L H 15(mm) 1/2" 125 66 125 66

20 3/4" 140 80 140 80 25 1" 160 80 160 80

32 11/4" 180 110 180 110 40 11/2" 190 110 190 110 50 2" 220 135 220 135

65 21/2" 270 195 270 195 80 3" 290 220 290 220

100 4" 350 260 350 260

125 5" 390 265 390 265 150 6" 440 315 440 315 200 8" 540 375 540 375

250 10" 680 490 680 490

MaterialBody SCS13A / CF8 SCS14A / CF8M

Screen SUS304 / F304 SUS316 / F316


Remarks Screen 40 Mesh

D1L

H D

L

L

H

11

Forged Stainless Steel Valves

Design Manufacturers StandardType Gate Valve Globe Valve Lift Check Valve Gate Valve Globe Valve Lift Check ValveClass 800

Screwed ends Screwed ends Screwed ends Socket welded ends Socket welded ends Socket welded endsFig. 842 840 844 842W 840W 844WSize L H D1 L H D1 L H L H D1 L H D1 L H

8 (mm) 1/4"10 3/8" 79 160 102 79 165 89 79 49 79 160 102 79 165 89 79 49

15 1/2" 79 160 102 79 165 89 79 49 79 160 102 79 165 89 79 49 20 3/4" 92 160 102 92 170 89 92 54 92 160 102 92 170 89 92 54 25 1" 111 190 121 111 202 102 111 73 111 190 121 111 202 102 111 73

32 11/4" 120 252 146 152 251 146 152 101 120 252 146 152 251 146 152 101 40 11/2" 120 252 146 152 251 146 152 101 120 252 146 152 251 146 152 101 50 2" 140 280 178 172 285 178 172 120 140 280 178 172 285 178 172 120

MaterialBody SUSF304 (HF) SUSF304 (HF) SUSF304 (HF) SUSF304 (HF) SUSF304 (HF) SUSF304 (HF)Stem SUS304 SUS304 — SUS304 SUS304 —Ball SUS304 (HF) SUS304 SUS304 SUS304 (HF) SUS304 SUS304


Remarks Flanged ends type in available on request (10K, 20K, 150lb, 300lb)Screwed ends: JIS B0203 ASME threads, socket welded available on request, socket welded ends: JPI 75-47

Pressure–Temperature Ratings

Temperature °C –29~38 50 100 150 200 250 300 325 350 375 400

Max. Allowable Pressure MPa 13.24 12.75 10.9 9.87 9.19 8.67 8.24 8.06 7.9 7.74 7.58

L L

L

D1

H

D1

H

H

12



■Gate, Globe, and Check Valves, strainers / screwed & flanged ends

High Performance Butterfly Valves

Class

Service conditions

10K 20K (Fig.809)

MPa MPa

Static water Less than 120°C 1.4 2.0

Air, oil, gas,steam

Less than 150°C 1.1 1.2

Less than 180°C 1.0 1.0

* Do not use our products in flammable or toxic gas service.

Class

Service conditions

600WOG 800WOG 10K

MPa MPa MPa

Water, oil, gas, 4.1 5.5 1.4

Saturated steam 1.0 1.0 1.0

* Do not use our products in flammable or toxic gas service.


■Ball Valves / screwed end type 　Fig. 3550(W), 4550A(W), 4580, 3380, 4760A or 3060

(MPa)

1.8

2.0

1.4

1.6

20K

10K

1.21.11.0

0.8

0.6

0.4

0.2

0

Pre

ssur

e (M

Pa)

–50 500 100 150 200 250 (°C)

Temperature (°C)

(MPa)

6.0

7.0

5.0

5.5

4.1

10K1.4

4.0

3.0

2.0

1.0

0P

ress

ure

(MP

a)–200 –100

← –196

0 100 200 (°C)

Temperature (°C)

–29 19517738 232500 150100 200 250 300 400350

Temperature (°C)

2.0

1.5

1.75

1.4

1.0

0.5

0.14

0

Pre

ssur

e (M

Pa)

Upper limit of size 250 & 300mm

← –29 ←180←120

Class 800

Class 600

← –29

13



■JIS Flanged Valves　　　　　　　　　　　　　　　　　　　　　　　　　　　 (MPa)

Nominal pressure 10K 20K

Body material SCS13A, SCS14A SCS13A, SCS14A

Tem

pera

ture

below 120°C 1.4 3.4

220°C 1.2 3.1

300°C 1.0 2.9

350°C — 2.6

400°C — 2.3

425°C — 2.0

Notes:

1) The max. working temperature for standard products is

restricted to 260°C by gland packing, gasket or material.

2) In case of use at 260°C and above, applicable selection for

gland packing & gasket is required.

3) Do not use our products in flammable or toxic gas service.

V-Series Stainless Steel Valves

■ASME B16.34 Table 2-2.1A & 2-2.2A

Service temperatureClass 150 Class 300

A351 Gr. CF8 (SCS13A) A351 Gr. CF8M (SCS14A) A351 Gr. CF8 (SCS13A) A351 Gr. CF8M (SCS14A)

(°C) (°F) MPa MPa MPa MPa

–29 –38 –20 –100 1.90 1.90 4.96 4.96

93 200 1.62 1.65 4.14 4.27

149 300 1.41 1.48 3.65 3.86

204 400 1.24 1.34 3.24 3.55

260 500 1.17 1.90 3.00 3.31

316 600 0.965 0.965 2.86 3.10

343 650 0.862 0.862 2.83 3.07

371 700 0.758 0.758 2.79 2.96

399 750 0.655 0.655 2.76 2.93

427 800 0.552 0.552 2.72 2.86

454 (2) 850 0.448 0.448 2.69 2.79

482 (2) 900 0.345 0.345 2.65 2.72

510 (2) 950 0.241 0.241 2.59 2.65

538 (2) 1000 0.138 0.138 2.24 2.52

566 (2) 1050 0.138 (1) 0.138 (1) 2.14 2.48

593 (2) 1100 0.138 (1) 0.138 (1) 1.79 2.24

621 (2) 1150 0.138 (1) 0.138 (1) 1.34 1.90

649 (2) 1200 0.138 (1) 0.138 (1) 1.07 1.41

677 (2) 1250 0.138 (1) 0.138 (1) 0.758 1.240

704 (2) 1300 0.138 (1) 0.138 (1) 0.586 0.965

732 (2) 1350 0.138 (1) 0.138 (1) 0.414 0.724

760 (2) 1400 0.138 (1) 0.138 (1) 0.345 0.517

788 (2) 1450 0.103 (1) 0.138 (1) 0.241 0.414

816 (2) 1500 0.069 (1) 0.138 (1) 0.172 0.276

Note: (1) For welding end valves only. Flanged ends ratings terminate at 1000°F.(2) Permissible, but please consult our sales staff or distributor for usage above 450°C.

– 50 0 120

10K Type

20K TypeSCS13A, SCS14A 20K Type

SCS13A, SCS14A

220260

350300 400 450

Temperature (°C)

3.53.4

3.1

1.2

1.4

1.0

2.0

2.3

2.6

2.9

0

Pre

ssur

e (M

Pa)

1）

– 29 425

14


10/20K, Class 150/300 Stainless Steel Flanged Ball Valves

(MPa)

7.0

6.0

5.0

4.0

3.0

2.0

1.0

Pre

ssur

e (M

Pa)

SIZE 15 & 20A

0 50 100 150 200 250 (°C)

Temperature (°C)

10K Body rating

150 Body rating

20K Body rating

300 Body rating

CF8 (SCS13A)

CF8 (SCS13A)

CF8M (SCS14A)

CF8M (SCS14A)

Seat rating (R-PTFE)

Seat rating (PTFE)

(MPa)

7.0

6.0

5.0

4.0

3.0

2.0

1.0

Pre

ssur

e (M

Pa)

SIZE 25～65A

0 50 100 150 200 250 (°C)

Temperature (°C)

10K Body rating

150 Body rating

20K Body rating

300 Body rating

CF8 (SCS13A)

CF8 (SCS13A)

CF8M (SCS14A)

CF8M (SCS14A)


Seat rating (PTFE)

(MPa)

7.0

6.0

5.0

4.0

3.0

2.0

1.0

Pre

ssur

e (M

Pa)

SIZE 80 & 100A

0 50 100 150 200 250 (°C)

Temperature (°C)

10K Body rating

150 Body rating

20K Body rating

300 Body rating CF8 (SCS13A)

CF8 (SCS13A)

CF8M (SCS14A)

CF8M (SCS14A)


Seat rating (PTFE)

(MPa)

7.0

6.0

5.0

4.0

3.0

2.0

1.0

Pre

ssur

e (M

Pa)

SIZE 200A

0 50 100 150 200 250 (°C)

Temperature (°C)

10K Body rating

150 Body rating

20K Body rating


CF8 (SCS13A)

CF8M (SCS14A)

CF8M (SCS14A)

Seat rating (R-PTFE)Seat rating (PTFE)

(MPa)

7.0

6.0

5.0

4.0

3.0

2.0

1.0

Pre

ssur

e (M

Pa)

SIZE 125 & 150A

0 50 100 150 200 250 (°C)

Temperature (°C)

10K Body rating

150 Body rating

20K Body rating


CF8 (SCS13A)

CF8M (SCS14A)

CF8M (SCS14A)Seat rating (R-PTFE)

Seat rating (PTFE)

15


Dual Plate Check Valves

■Rubber Seat (with Bypass-Valve)

Fig. 806, 10K

　　　　　Seat material

Service conditions　　　NBR FKM EPDM

MPa MPa MPa

Static waterbelow 80°C 1.4 1.4 1.4

above 120°C — — 1.4

Oil, water, airbelow 80°C 1.0 1.0 1.0

above 120°C — 1.0 1.0

Note: An EPDM seat shall not be used for all oil application.

Fig. 816, 20K

　　　　　Seat material

Service conditions　　　NBR FKM EPDM

MPa MPa MPa

Static waterbelow 80°C 3.4 3.4 3.4

above 120°C — — 3.4

Oil, water, airbelow 80°C 2.6 2.6 2.6

above 120°C — 2.0 2.0

Note: An EPDM seat shall not be used for all oil applications.

■Service Temperature Range

NBR (Buna-N) seat 0°C to +80°C

FKM seat 0°C to +120°C

EPDM seat –20°C to +120°C

■Metal Seat (without Bypass-Valve)

Fig. 806M(10K) and 816M(20K)

　　　　　 Ratings

Service conditions　　　10K 20K

MPa MPa

Static water

Oil, gas, water, air

below 120°C 1.4 3.4

above 220°C 1.2 3.1

Test pressureshell water 2.1 5.0

seat air 0.6 0.6

Note: 1) Standard products are designed up to 150°C. 2) in case of use at 150°C & above, please consult us. 3) Do not use our products in flammable or toxic gas service.

Fig. 806MW(150) and 816MW(300)Please refer to table for ASME B16.34.

Note: 1) Standard products are designed up to 150°C. 2) In case of use at 150°C & above, please consult us. 3) Do not use our products in flammable or toxic gas service.

Y-450=03

1307①ITP

y-450=03jis b 2002 screwed: jis b 0203 flanged: jis b 2220 jv8-1 scs13a/cf8 non-asbestos — ball...

Documents