y: aimplas. instituto tecnolÓgico del plÁstico · contenido en negro de carbono en poliolefinas y...
TRANSCRIPT
![Page 1: y: AIMPLAS. INSTITUTO TECNOLÓGICO DEL PLÁSTICO · Contenido en negro de carbono en poliolefinas y sus ... Contenido en fibra de vidrio ... La vigencia de la acreditación y del](https://reader031.vdocuments.net/reader031/viewer/2022022013/5b34d6147f8b9aec518c9998/html5/thumbnails/1.jpg)
Acreditación/Accreditation nº 56/LE156 Anexo Técnico Rev. /Technical Annex Ed.22
Fecha/Date 27/11/2015 Hoja/Page 1 de 25
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
ANEXO TÉCNICO ACREDITACIÓN Nº 56/LE156 SCHEDULE OF ACCREDITATION
Entidad/Entity: AIMPLAS. INSTITUTO TECNOLÓGICO DEL PLÁSTICO
Dirección/Address: C/ Gustave Eiffel, 4. Parque Tecnológico de Valencia, Apdo. 51; 46980 Paterna (Valencia) Norma de referencia/Reference Standard: UNE-EN ISO/IEC 17025: 2005 Ensayos en la siguiente área/Test in the following area:
Materiales plásticos y composites / Plástic and composites
Categoría 0 (Ensayos en el laboratorio permanente) Category 0 (Test in the permanent laboratory)
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Materiales Plásticos Plástic
Plásticos
Plastics
Propiedades en tracción Fuerza:(0,02 N-250 kN)
Alargamiento: (10 mm -500 mm)
Tensile properties Force:(0,02 N-250 KN)
Elongation: (10 mm -500 mm)
ASTM D638-10 Probetas/Specimens I, II, III,IV UNE-EN ISO 527-1:2012 UNE-EN ISO 527-2:2012
Propiedades en flexión
Fuerza: (0,02 N-250 kN)
Flexural properties Force: (0,02 N-250 KN)
UNE-EN ISO 178: 2011+A1:2013 ASTM D790-10
Índice de fluidez en masa (IFM) y en volumen (IFV) Temperatura máx.: 400 ºC
(0,1-250) cm3/10 min
Melt flow index in mass (MFR) and in volume (MVR) Maximum temperature: 400°C
(0,1-250) cm3/10 min
ASTM D1238-13 (Método/Method A,B,C) UNE-EN ISO 1133-1:2012 UNE-EN ISO 1133-2:2012
Código Validación Electrónica: 1CKAg415A7JL1a2hA9
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
![Page 2: y: AIMPLAS. INSTITUTO TECNOLÓGICO DEL PLÁSTICO · Contenido en negro de carbono en poliolefinas y sus ... Contenido en fibra de vidrio ... La vigencia de la acreditación y del](https://reader031.vdocuments.net/reader031/viewer/2022022013/5b34d6147f8b9aec518c9998/html5/thumbnails/2.jpg)
Acreditación/Accreditation nº 56/LE156 Anexo Técnico Rev. /Technical Annex Ed.22
Fecha/Date 27/11/2015 Hoja/Page 2 de 25
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Temperatura de reblandecimiento Vicat
(Tª ambiente a 200 ºC)
Vicat softening temperature (Room temperature up to 200°C)
ASTM D1525-09 UNE-EN ISO 306:2015
Envejecimiento artificial acelerado (lámpara de arco de xenón)
Accelerated artificial weathering (xenon arc lamp)
UNE-EN ISO 4892-1:2001 UNE-EN ISO 4892-2:2014 UNE-ISO 4582:2014 Ap. 4.1.4.3. UNE-EN 20105-A02:1998
Densidad y densidad relativa de materiales plásticos no celulares
Density and relative density of non cellular plastic materials.
ASTM D792-13 UNE-EN ISO 1183-1:2013 Método/Method A
Dureza Shore A y D
Shore A (20 – 90) Shore D (20 – 90)
Shore A and D Hardness
Shore A (20 – 90) Shore D (20 – 90)
UNE-EN ISO 868:2003 ASTM D2240-05 (2010) UNE-ISO 7619-1:2011 UNE-ISO 7619-1 :2011 ERRATUM :2011
Dureza Barcol
(0UB -100 UB)
Barcol Hardness (0 UB -100 UB)
UNE 53270: 2012
ASTM D2583-13a
Identificación de materiales: Análisis cualitativo por Espectrofotometría de infrarrojos con transformada de Fourier (FTIR)
Identification of materials: Qualitative analysis by Fourier Transformed Infrared Spectrophotometry (FTIR)
Procedimiento interno In-house method
QE15
Propiedades en compresión
(0,02 N – 250 kN)
Compressive properties
(0,02 N – 250 kN)
UNE-EN ISO 604: 2003
Código Validación Electrónica: 1CKAg415A7JL1a2hA9
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
![Page 3: y: AIMPLAS. INSTITUTO TECNOLÓGICO DEL PLÁSTICO · Contenido en negro de carbono en poliolefinas y sus ... Contenido en fibra de vidrio ... La vigencia de la acreditación y del](https://reader031.vdocuments.net/reader031/viewer/2022022013/5b34d6147f8b9aec518c9998/html5/thumbnails/3.jpg)
Acreditación/Accreditation nº 56/LE156 Anexo Técnico Rev. /Technical Annex Ed.22
Fecha/Date 27/11/2015 Hoja/Page 3 de 25
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Migración global en simulantes acuosos y simulantes alternativos al graso (iso-octano y etanol al 95%)
Overall migration into aqueous simulants and alternative oil simulants (iso-octane and ethanol 95%)
UNE-EN 1186-1:2002 UNE-EN 1186-3:2002 UNE-EN 1186-5:2002 UNE-EN 1186-9:2002 UNE-EN 1186-14:2003
Reglamento (UE) Nº10/2011 de la comisión de 14 de enero de 2011 sobre materiales y objetos plásticos destinados a entrar en contacto con alimentos Commission Regulation (EU) Nº 10/2011 of 14 January 2011 on plastic materials and articles intended to come into contact with food
Dureza a la bola
Hardness according to ball indentation method.
UNE-EN ISO 2039-1: 2003
Temperatura de flexión bajo carga
(Tª ambiente a 200 ºC)
Determination of temperature of deflection under load.
(Room temperature up to 200ºC)
UNE-EN ISO 75-1:2013
UNE-EN ISO 75-2:2013
Impacto Charpy (2 -25 J)
Charpy impact test (2 -25 J)
UNE-EN ISO 179-1: 2011
Impacto Izod (2,75 -25 J)
Izod impact test (2.75 -25 J)
UNE-EN ISO 180: 2001 UNE-EN ISO 180: 2001/A1: 2007
UNE-EN ISO 180:2001/A2:2013
Contenido en negro de carbono en poliolefinas y sus transformados (analizador termogravimétrico)
Carbon black content in polyolefins and their products (thermogravimetric analyzer)
UNE-EN ISO 11358-1:2015 UNE 53375-3 :2011
Determinación de temperatura y entalpía de fusión y cristalización y Determinación de temperatura de transición vítrea (DSC) (50 ºC – 400 ºC)
Determination of temperature and enthalpy of melting and crystallization and determination of glass transition temperature (DSC) (50ºC – 400ºC)
UNE-EN ISO 11357-1:2010 UNE-EN ISO 11357-2:2015 UNE-EN ISO 11357-3:2013
Código Validación Electrónica: 1CKAg415A7JL1a2hA9
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
![Page 4: y: AIMPLAS. INSTITUTO TECNOLÓGICO DEL PLÁSTICO · Contenido en negro de carbono en poliolefinas y sus ... Contenido en fibra de vidrio ... La vigencia de la acreditación y del](https://reader031.vdocuments.net/reader031/viewer/2022022013/5b34d6147f8b9aec518c9998/html5/thumbnails/4.jpg)
Acreditación/Accreditation nº 56/LE156 Anexo Técnico Rev. /Technical Annex Ed.22
Fecha/Date 27/11/2015 Hoja/Page 4 de 25
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Tiempo de inducción a la oxidación
Oxidation induction time
UNE-EN 728:1997 UNE-EN ISO 11357-6:2013 ASTM D3895-14
Películas y hojas de plástico
Films and plastic sheets
Resistencia al impacto (Método de caída de dardo) (42,5 g -1500 g)
Impact resistance (Falling dart impact method) (42.5 g -1500 g)
ASTM D1709-15a UNE-EN ISO 7765-1:2005
Propiedades en tracción Fuerza: (0,02 N- 250 kN) Alargamiento: (10 mm -500mm) Tensile properties
Force: (0,02 N- 250 kN) Elongation: (10 mm -500mm)
ASTM D882-12 UNE-EN ISO 527-3:1996 UNE-EN ISO 527-1:2012 UNE-EN ISO 527-3/AC: 2002
Coeficiente de rozamiento estático y dinámico Fuerza: (0,02 N-250 kN)
Static and kinetic coefficients of friction Force: (0,02 N-250 KN)
UNE-EN ISO 8295:2005 ASTM D1894-14
Espesor (medida micrométrica)
Thickness (mechanical scannig method)
(0 m -2000 μm)
UNE-ISO 4593:2010
Resistencia al rasgado (método de la probeta pantalón)
Tear resistance (trouser specimen)
(0,02 N-250 kN)
UNE-EN ISO 6383-1:2005
Resistencia a la separación por pelado (peeling test)
T-peel test
(0,02 N-250 kN)
Procedimiento interno In-house method
ME16 ASTM F88/F88-09 ASTM F904-98 (2008) Excepto Apdo./Except.Par 11.3.3 UNE-EN ISO 11339:2010
Gramaje
Grammage
(0 g -1000 g)
Procedimiento interno In-house method
ME23
Identificación de materiales: Análisis cualitativo por Espectrofotometría de infrarrojos con Transformada de Fourier (FTIR)
Identification of materials: Qualitative analysis by Fourier Transformed Infrared Spectrophotometry (FTIR)
Procedimiento interno In-house method QE15
Código Validación Electrónica: 1CKAg415A7JL1a2hA9
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
![Page 5: y: AIMPLAS. INSTITUTO TECNOLÓGICO DEL PLÁSTICO · Contenido en negro de carbono en poliolefinas y sus ... Contenido en fibra de vidrio ... La vigencia de la acreditación y del](https://reader031.vdocuments.net/reader031/viewer/2022022013/5b34d6147f8b9aec518c9998/html5/thumbnails/5.jpg)
Acreditación/Accreditation nº 56/LE156 Anexo Técnico Rev. /Technical Annex Ed.22
Fecha/Date 27/11/2015 Hoja/Page 5 de 25
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Velocidad de transmisión de oxígeno a través de filmes y láminas de plástico (método culombimétrico) (“permeabilidad” a oxígeno) (0,005-2000) cm
3/m
2 día))
- Ambiente seco
- Humedad controlada (35-90%)
Oxygen transmission rate through plastic films and sheets (coulometric method) (‘oxygen permeability’) ((0,005-2000) cm
3/m
2 day))
- Dry environment - Controlled humidity (35-90%)
ASTM D3985-05 (2010)e1 ASTM F1927-14
Plásticos reforzados con fibra de vidrio
Textile glass reinforced plastics
Propiedades de flexión
Flexural properties
(0,02 N-250 kN)
UNE-EN ISO 14125: 1999 UNE-EN ISO 14125/AC:2002 UNE-EN ISO 14125/A1:2011 ASTM D790-10
Contenido en fibra de vidrio
Determination of glass fibre content
(500 ºC - 650 ºC)
UNE-EN ISO 1172:1999 Método A Apdo. 7.1
Propiedades en tracción
Fuerza: (0,02 N- 250 kN) Alargamiento: (10 mm -500mm)
Tensile properties
Force: (0,02 N- 250 kN) Elongation: (10 mm -500mm)
ASTM D638-10 (Specimen Type I) UNE-EN ISO 527-4:1997 Probeta Tipo/Specimen Type 1B-2-3
Resistencia química
Chemical resistance
UNE 53316:2012
Dureza Barcol
Barcol Hardness
(0 UB - 100 UB)
EN 59: 1977 ASTM D2583-13 UNE 53270:2012
Temperatura de flexión bajo carga
(Tª ambiente a 200 ºC)
Determination of temperature of deflection under load.
(Room temperature up to 200ºC)
UNE-EN ISO 75-1:2013 UNE-EN ISO 75-2:2013
Código Validación Electrónica: 1CKAg415A7JL1a2hA9
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
![Page 6: y: AIMPLAS. INSTITUTO TECNOLÓGICO DEL PLÁSTICO · Contenido en negro de carbono en poliolefinas y sus ... Contenido en fibra de vidrio ... La vigencia de la acreditación y del](https://reader031.vdocuments.net/reader031/viewer/2022022013/5b34d6147f8b9aec518c9998/html5/thumbnails/6.jpg)
Acreditación/Accreditation nº 56/LE156 Anexo Técnico Rev. /Technical Annex Ed.22
Fecha/Date 27/11/2015 Hoja/Page 6 de 25
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Resistencia a la cizalla interlaminar aparente por el ensayo de flexión con poca separación entre apoyos
(0,02 N-250 kN)
Apparent interlaminar shear strength by short-beam method (0,02 N-250 kN)
UNE-EN ISO 14130:1999
Elastómeros
Elastomers
Densidad específica
Specific density
UNE-EN ISO 1183-1:2013 Método/Method A
Propiedades en tracción (0,02 N-250 kN)
Tensile properties Force: (0,02 N- 250 kN) Elongation: (10 mm -500mm)
DIN 53504: 2009 UNE-ISO 37:2013
Dureza Shore A Shore A (20 – 90)
Shore A Hardness Shore A (20 – 90)
ASTM D 2240-05 (2010) UNE- ISO 7619-1:2011
UNE-EN ISO 868:2003
Resistencia al desgarro
Tear resistance
(0,02 N- 250 kN)
ISO 34-1:2011 Probeta pantalón y Probeta angular/Trouser and angle
specimen
Plásticos celulares rígidos y flexibles
Rigid and flexible cellular plastics
Propiedades en compresión
(0,02 N- 250 kN)
Compressive properties (0,02 N- 250 kN)
ASTM D1621-10 UNE-EN ISO 844:2015
Propiedades en tracción Fuerza: (0,02 N- 250 kN)
Alargamiento: (10 mm - 500mm)
Tensile properties Force: (0,02 N- 250 kN) Elongation: (10 mm -500mm)
UNE 53190:2001 UNE-EN ISO 1798:2008 ISO 1926: 2015
Tejidos recubiertos de materiales plásticos
Plastic coated fabrics
Resistencia al desgarro
Tear resistance
(0,02 N- 250 kN)
UNE-EN ISO 4674-1:2004 (probeta tipo pantalón)/(Trouser
specimen)
Código Validación Electrónica: 1CKAg415A7JL1a2hA9
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
![Page 7: y: AIMPLAS. INSTITUTO TECNOLÓGICO DEL PLÁSTICO · Contenido en negro de carbono en poliolefinas y sus ... Contenido en fibra de vidrio ... La vigencia de la acreditación y del](https://reader031.vdocuments.net/reader031/viewer/2022022013/5b34d6147f8b9aec518c9998/html5/thumbnails/7.jpg)
Acreditación/Accreditation nº 56/LE156 Anexo Técnico Rev. /Technical Annex Ed.22
Fecha/Date 27/11/2015 Hoja/Page 7 de 25
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Perfiles de poli (cloruro de vinilo) no plastificado (PVC-U) para lamas de persiana enrollable UNE 53141
Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of lames of scrollable blind according to: UNE 53141
Temperatura de reblandecimiento Vicat (VST)
Tª ambiente a 200 ºC
Vicat softening temperature (VST) (Room temperature up to 200°C)
UNE-EN ISO 306:2015
Módulo de elasticidad en flexión
Flexural Modulus
(0,02 N- 250 kN)
UNE-EN ISO 178:2011
Envejecimiento artificial acelerado (lámpara de arco de xenón)
Accelerated artificial weathering (xenon arc lamp)
UNE-EN 513:2000 Excepto Apdo./Except.Par 8.10 UNE-EN 513: 2000 ERRATUM
Perfiles de poli (cloruro de vinilo) no plastificado para la fabricación de ventanas. UNE-EN 12608
Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors according to: UNE-EN 12608
Temperatura de reblandecimiento Vicat (VST)
Tª ambiente a 200 ºC
Vicat softening temperature (Room temperature up to 200°C)
UNE-EN ISO 306:2015 ASTM D1525-09
Envejecimiento artificial acelerado (lámpara de arco de xenón)
Accelerated artificial weathering (xenon arc lamp)
UNE-EN 513: 2000 Excepto Apdo./Except.Par 8.10 UNE-EN 513: 2000 ERRATUM
Módulo de elasticidad en flexión
Flexural Modulus
(0,02 N- 250 kN)
UNE-EN ISO 178:2011
Perfiles de poli(cloruro de vinilo) no plastificado (PVC-U) para la fabricación de cajones de persiana UNE 53948 EX
Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of drawer of shutters according to: UNE 53948 EX
Temperatura de reblandecimiento Vicat (VST)
Tª ambiente a 200 ºC
Vicat softening temperature (room temperature up to 200°C)
UNE-EN ISO 306:2015
Módulo de elasticidad en flexión
Flexural Modulus
(0,02 N- 50 kN)
UNE-EN ISO 178:2011
Envejecimiento artificial acelerado (lámpara de arco de xenón)
Accelerated artificial weathering (xenon arc lamp)
UNE-EN 513:2000 Excepto Apdo./Except.Par 8.10 UNE-EN 513: 2000 ERRATUM
Impacto Charpy
Charpy Impact
(2 -25 J)
UNE-EN ISO 179-1:2011
Código Validación Electrónica: 1CKAg415A7JL1a2hA9
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
![Page 8: y: AIMPLAS. INSTITUTO TECNOLÓGICO DEL PLÁSTICO · Contenido en negro de carbono en poliolefinas y sus ... Contenido en fibra de vidrio ... La vigencia de la acreditación y del](https://reader031.vdocuments.net/reader031/viewer/2022022013/5b34d6147f8b9aec518c9998/html5/thumbnails/8.jpg)
Acreditación/Accreditation nº 56/LE156 Anexo Técnico Rev. /Technical Annex Ed.22
Fecha/Date 27/11/2015 Hoja/Page 8 de 25
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Bolsas de mercado de plástico, para uso alimentario. UNE 53257-1 UNE 53257-2
Shopping plastic bags for alimentary use according to: UNE 53257-1 UNE 53257-2
Resistencia al impacto (Método caída de dardo)
Impact resistance (Falling dart impact method)
(42,5 g -1500 g)
UNE-EN ISO 7765-1:2005
Propiedades en tracción Fuerza: (0,02 N- 250 kN) Alargamiento: (10 mm -500mm)
Tensile properties Force: (0,02 N- 250 kN) Elongation: (10 mm -500mm)
UNE 53257-1:1988 Apdo. 5.4 UNE-EN ISO 527-3: 1996 UNE-EN ISO 527-3/AC:2002
Láminas flexibles para impermeabilización.
Flexible sheet for waterproofing according to:
UNE-EN 13956 UNE-EN 13707 UNE-EN 13859-1 UNE-EN 13859-2 UNE-EN 13967 UNE-EN 13969 UNE-EN 13970 UNE-EN 13984
Espesor
Thickness
UNE-EN 1849-1:2000 UNE-EN 1849-2:2010
Masa por unidad de superficie
Mass per surface unit
UNE-EN 1849-1:2000 UNE-EN 1849-2:2010
Estanquidad al agua
Watertightness
UNE-EN 1928:2000
Resistencia al pelado de los solapes
Peel resistance of joints
(0,02 N- 250 kN)
UNE-EN 12316-1:2000 UNE-EN 12316-2:2013
Resistencia al cizallamiento de los solapes
Shear resistance of joints
(0,02 N- 250 kN)
UNE-EN 12317-1:2000 UNE-EN 12317-2:2011
Propiedades en tracción Fuerza: (0,02 N- 250 kN) Alargamiento: (10 mm -500mm)
Tensile properties Force: (0,02 N- 250 kN) Elongation: (10 mm -500mm)
UNE-EN 12311-1:2000 UNE-EN 12311-2:2013
Resistencia al impacto
Resistance to impact
UNE-EN 12691:2006
Resistencia a una carga estática
Resistance to static loading
UNE-EN 12730:2001
Código Validación Electrónica: 1CKAg415A7JL1a2hA9
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
![Page 9: y: AIMPLAS. INSTITUTO TECNOLÓGICO DEL PLÁSTICO · Contenido en negro de carbono en poliolefinas y sus ... Contenido en fibra de vidrio ... La vigencia de la acreditación y del](https://reader031.vdocuments.net/reader031/viewer/2022022013/5b34d6147f8b9aec518c9998/html5/thumbnails/9.jpg)
Acreditación/Accreditation nº 56/LE156 Anexo Técnico Rev. /Technical Annex Ed.22
Fecha/Date 27/11/2015 Hoja/Page 9 de 25
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Resistencia al desgarro
Tear resistance
(0,02 N- 50 kN)
UNE-EN 12310-1:2000 UNE-EN 12310-2:2001
Plegabilidad a baja temperatura (flexibilidad)
Foldability at low temperatura (flexibility)
UNE-EN 495-5:2013 UNE-EN 1109:2013
Estabilidad dimensional a temperatura elevada (método del calibre)
Dimensional stability (caliper method)
UNE-EN 1107-1:2000 (Método/Method B) UNE-EN 1107-2:2001
Durabilidad de la estanqueidad frente al envejecimiento
Artificial ageing by long term exposure to elevated temperature. Watertightness durability
UNE-EN 1296:2001 UNE-EN 1928:2000
Resistencia a fluencia
Yield resistance
UNE-EN 1110:2011
Contenido en cenizas
Ash content
UNE 104281-1-7:1986
Pérdida de gránulos
Adhesion of granules
UNE-EN 12039:2000
Barreras geosintéticas
Geosynthetic barriers according to:
UNE-EN 13361 UNE-EN 13362 UNE-EN 13491 UNE-EN 13492 UNE-EN 13493
Resistencia al desgarro
Tear resistance
(0,02 N- 250 kN)
ISO 34-1: 2011 UNE-EN 12310-1:2000
UNE 53516-1:2001
Propiedades en tracción Fuerza: (0,02 N- 250 kN) Alargamiento: (10 mm -500mm)
Tensile properties Force: (0,02 N- 250 kN) Elongation: (10 mm -500mm)
UNE-EN ISO 527-1:2012 UNE-EN ISO 527-3: 1996 UNE-EN ISO 527-3/AC:2002 UNE-EN ISO 527-4:1997 UNE-EN 12311-1:2000 UNE-EN ISO 10319:2008
Espesor
Thickness
UNE-EN 1849-2:2010 UNE-EN 1849-1:2000
Masa por unidad de superficie
Mass per surface unit
UNE-EN 1849-2:2010 UNE-EN 1849-1:2000
Código Validación Electrónica: 1CKAg415A7JL1a2hA9
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
![Page 10: y: AIMPLAS. INSTITUTO TECNOLÓGICO DEL PLÁSTICO · Contenido en negro de carbono en poliolefinas y sus ... Contenido en fibra de vidrio ... La vigencia de la acreditación y del](https://reader031.vdocuments.net/reader031/viewer/2022022013/5b34d6147f8b9aec518c9998/html5/thumbnails/10.jpg)
Acreditación/Accreditation nº 56/LE156 Anexo Técnico Rev. /Technical Annex Ed.22
Fecha/Date 27/11/2015 Hoja/Page 10 de 25
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Punzonado estático
Static puncture (CBR)
(0,02 N- 50 kN)
UNE-EN ISO 12236:2007
Comportamiento a bajas temperaturas (plegado)
Foldability at low temperatura
UNE-EN 495-5:2013
Envejecimiento térmico (Resistencia a la oxidación)
Oxidation. Thermal ageing.
UNE-EN 14575:2007
Contenido en negro de carbono en poliolefinas y sus transformados (analizador termogravimétrico)
Carbon black content in polyolefins and their products (thermogravimetric analyzer)
UNE 53375-3:2011
Dispersión de negro de carbono o pigmento (Método de comprensión)
Carbon black or pigment dispersion (compression method)
ISO 18553:2002
ISO 18553:2002/Amd 1:2007
Tiempo de inducción a la oxidación
Oxidation induction time
UNE-EN 728.1997 UNE-EN ISO 11357-6:2013 ASTM D3895-14
Impermeabilización. Materiales bituminosos y bituminosos modificados. Láminas de alquitrán modificado con polímero UNE 104244
Bituminous and bituminous modified materials. Polymer modified tar sheets according to: UNE 104244
Espesor
Thickness
UNE-EN 1849-1:2000
Masa por unidad de área
Mass per surface unit
UNE-EN 1849-1:2000
Propiedades en tracción Fuerza: (0,02 N- 250 kN) Alargamiento: (10 mm -500mm)
Tensile properties Force: (0,02 N- 250 kN) Elongation: (10 mm -500mm)
UNE-EN 12311-2:2013
Dureza Shore A y D Shore A (20 – 90) Shore D (20 – 90)
Shore A and D hardness Shore A (20 – 90) Shore D (20 – 90)
UNE-EN ISO 868: 2003
Código Validación Electrónica: 1CKAg415A7JL1a2hA9
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
![Page 11: y: AIMPLAS. INSTITUTO TECNOLÓGICO DEL PLÁSTICO · Contenido en negro de carbono en poliolefinas y sus ... Contenido en fibra de vidrio ... La vigencia de la acreditación y del](https://reader031.vdocuments.net/reader031/viewer/2022022013/5b34d6147f8b9aec518c9998/html5/thumbnails/11.jpg)
Acreditación/Accreditation nº 56/LE156 Anexo Técnico Rev. /Technical Annex Ed.22
Fecha/Date 27/11/2015 Hoja/Page 11 de 25
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Resistencia a una carga estática
Resistance to static loading
UNE-EN 12730:2001
Resistencia al impacto
Resistance to impact
UNE-EN 12691:2006
Estabilidad dimensional
Dimensional stability
UNE-EN 1107-2:2001
Placas bituminosas con armadura mineral y/o sintética
Bitumen shingles with mineral and/or synthetic reinforcements according to: UNE-EN 544
Propiedades en tracción Fuerza: (0,02 N- 250 kN) Alargamiento: (10 mm -500mm)
Tensile properties Force: (0,02 N- 250 kN) Elongation: (10 mm -500mm)
UNE-EN 12311-1:2000
Resistencia al desgarro
Tear resistance
(0,02 N- 50 kN)
UNE-EN 12310-1:2000
Sacos para el transporte para ayuda alimentaria. Sacos de película de polietileno
Sacks for the transport of food aid. Sacks made of polyethylene film according to: UNE-EN 787
Propiedades en tracción Fuerza: (0,02 N- 250 kN) Alargamiento: (10 mm -500mm)
Tensile properties Force: (0,02 N- 250 kN) Deformation: (10 mm -500mm)
UNE-EN ISO 527-3: 1996 UNE-EN ISO 527-3/AC: 2002
Resistencia de la soldadura del saco
Resistance of sack weld
(0,02 N- 50 kN)
UNE-EN 787: 1995 Apdo. 5.4.2 UNE-EN ISO 527-3: 1996 UNE-EN ISO 527-3/AC:2002
Resistencia al impacto (Método caída de dardo)
Impact resistance (Falling dart impact method)
(42.5 g -1500 g)
UNE-EN ISO 7765-1: 2005
Código Validación Electrónica: 1CKAg415A7JL1a2hA9
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
![Page 12: y: AIMPLAS. INSTITUTO TECNOLÓGICO DEL PLÁSTICO · Contenido en negro de carbono en poliolefinas y sus ... Contenido en fibra de vidrio ... La vigencia de la acreditación y del](https://reader031.vdocuments.net/reader031/viewer/2022022013/5b34d6147f8b9aec518c9998/html5/thumbnails/12.jpg)
Acreditación/Accreditation nº 56/LE156 Anexo Técnico Rev. /Technical Annex Ed.22
Fecha/Date 27/11/2015 Hoja/Page 12 de 25
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Sacos para el transporte para ayuda alimentaria. Sacos tubulares de película de material complejo.
Sacks for the transport of food aid. Tubular sacks made of composite film according to: UNE-EN 788
Propiedades en tracción Fuerza: (0,02 N- 250 kN) Alargamiento: (10 mm -500mm)
Tensile properties Force: (0,02 N- 250 kN) Elongation: (10 mm -500mm)
UNE-EN ISO 527-3: 1996 UNE-EN ISO 527-3/AC:2002
Adhesión de la película compleja
Multilayer film adhesion
(0,02 N- 250 kN)
UNE-EN 788: 1995 Apdo. 5.4.2 UNE-EN ISO 527-3:1996 UNE-EN ISO 527-3/AC: 2002
Resistencia de las soldaduras termoselladas de los sacos tubulares
Resistance of thermosealed weld of tubular sacks
(0,02 N- 250 kN)
UNE-EN 788: 1995 Apdo. 5.4.4 UNE-EN ISO 527-3: 1996 UNE-EN ISO 527-3/AC:2002
Tanques termoplásticos fijos para almacenamiento en superficie de gasóleos domésticos de calefacción, queroseno y combustibles diesel Tanques de polietileno moldeados por soplado.
Thermoplastics static tanks for above ground storage of domestic heating oils, kerosene and diesel fuels. Blow moulded polyethylene tanks according to: UNE-EN 13341
Densidad
Density
UNE-EN 13341:2005+A1.2011 Apdo. A.1.1
UNE-EN ISO 1183-1:2013 Método/Method A
Índice de fluidez en masa (IFM) Temperatura máx.: 400°C
Melt flow index in mass (MFR) and in volume (MVR) Maximum temperature: 400°C
(0,1-250) cm3/10 min
UNE-EN ISO 1133-1:2012
UNE-EN ISO 1133-2:2012
Resistencia a los carburantes
Oils resistance
UNE-EN 13341:2005 +A1 :2011 Apdo. A.1.4 UNE-EN ISO 527-1: 2012 UNE-EN ISO 527-2: 2012 UNE-EN ISO 175: 2011
Resistencia a la intemperie: Envejecimiento artificial acelerado (lámpara de arco de xenón)
Weathering resistance: Accelerated artificial weathering (xenon arc lamp)
UNE-EN 13341:2005+A.1:2011 Apdo. A.1.3 A.1.5 UNE-EN ISO 4892-1: 2001 UNE-EN ISO 4892-2: 2014
Código Validación Electrónica: 1CKAg415A7JL1a2hA9
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
![Page 13: y: AIMPLAS. INSTITUTO TECNOLÓGICO DEL PLÁSTICO · Contenido en negro de carbono en poliolefinas y sus ... Contenido en fibra de vidrio ... La vigencia de la acreditación y del](https://reader031.vdocuments.net/reader031/viewer/2022022013/5b34d6147f8b9aec518c9998/html5/thumbnails/13.jpg)
Acreditación/Accreditation nº 56/LE156 Anexo Técnico Rev. /Technical Annex Ed.22
Fecha/Date 27/11/2015 Hoja/Page 13 de 25
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Propiedades en tracción Fuerza: (0,02 N- 250 kN) Alargamiento: (10 mm -500mm)
Tensile properties Force: (0,02 N- 250 kN) Elongation: (10 mm -500mm)
UNE-EN 13341:2005 + A1 :2011 Apdo. A.1.3 UNE-EN ISO 527-2:2012
Capacidad
Capacity
UNE-EN 13341:2005 +A1:2011 Apdo. B.1
Aspecto visual
Appearance
UNE-EN 13341:2005 +A1:2011 Apdo. B.2
Masa
Mass
(0 - 3000 kg)
UNE-EN 13341:2005 +A1:2011 Apdo. B.3
Espesor de pared
Wall thickness
UNE-EN 13341:2005 +A1:2011 Apdo. B.4
Resistencia al impacto
Impact resistance
UNE-EN 13341:2005+A1:2011 Apdo. B.5
Alargamiento
Elongation
UNE-EN 13341:2005+A1:2011 Apdo. B.6.1
Deformación
Deformation
UNE-EN 13341:2005+A1:2011 Apdo. B.6.2
Resistencia a la presión
Pressure resistance
UNE-EN 13341:2005 +A1:2011 Apdo. B.7
Estanqueidad
Leak test
UNE-EN 13341:2005 +A1:2011 Apdo. B.8
Código Validación Electrónica: 1CKAg415A7JL1a2hA9
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
![Page 14: y: AIMPLAS. INSTITUTO TECNOLÓGICO DEL PLÁSTICO · Contenido en negro de carbono en poliolefinas y sus ... Contenido en fibra de vidrio ... La vigencia de la acreditación y del](https://reader031.vdocuments.net/reader031/viewer/2022022013/5b34d6147f8b9aec518c9998/html5/thumbnails/14.jpg)
Acreditación/Accreditation nº 56/LE156 Anexo Técnico Rev. /Technical Annex Ed.22
Fecha/Date 27/11/2015 Hoja/Page 14 de 25
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Tanques termoplásticos fijos para almacenamiento en superficie de gasóleos domésticos de calefacción, queroseno y combustibles diesel Tanques de polietileno fabricados por moldeo rotacional.
Thermoplastics static tanks for above ground storage of domestic heating oils, kerosene and diesel fuels. Rotationally moulded polyethylene tanks according to: UNE-EN 13341
Densidad
Density
UNE-EN 13341:2005 +A1:2011 Apdo. A.2.1
UNE-EN ISO 1183-1:2013 Método/Method A
Índice de fluidez en masa (IFM) Temperatura máx.: 400ºC
Melt flow index in mass (MFR) and in volume (MVR) Maximum temperature.: 400ºC
(0,1-250) cm3/10 min
UNE-EN 13341:2005+A1:2011 Apdo. A.2.2. UNE-EN ISO 1133-1:2012 UNE-EN ISO 1133-2:2012
Resistencia a los carburantes
Oils resistance
UNE-EN 13341:2005 +A1:2011 Apdo. A.2.4 UNE-EN ISO 527-2:2012 UNE-EN ISO 175: 2011
Resistencia a la intemperie: Envejecimiento artificial acelerado (lámpara de arco de xenón)
Weathering resistance: Accelerated artificial weathering (xenon arc lamp)
UNE-EN 13341:2005 +A1:2011 Apdo. A.2.3 and A.2.5 UNE-EN ISO 4892-1: 2001 UNE-EN ISO 4892-2: 2014
Propiedades en tracción Fuerza: (0,02 N- 250 kN) Alargamiento: (10 mm -500mm)
Tensile properties Force: (0,02 N- 250 kN) Elongation:: (10 mm -500mm)
UNE-EN 13341:2005+A1:2011 Apdo. A.2.3 UNE-EN ISO 527-2:2012
Capacidad
Capacity
UNE-EN 13341:2005 +A1:2011 Apdo. B.1
Aspecto visual
Appearance
UNE-EN 13341:2005 +A1:2011 Apdo. B.2
Masa
Mass
(0 - 3000 kg)
UNE-EN 13341:2005 +A1:2011 Apdo. B.3
Espesor de pared
Wall thickness
UNE-EN 13341:2005 +A1:2011 Apdo. B.4
Resistencia al impacto
Impact resistance
UNE-EN 13341:2005 +A1:2011 Apdo. B.5
Código Validación Electrónica: 1CKAg415A7JL1a2hA9
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
![Page 15: y: AIMPLAS. INSTITUTO TECNOLÓGICO DEL PLÁSTICO · Contenido en negro de carbono en poliolefinas y sus ... Contenido en fibra de vidrio ... La vigencia de la acreditación y del](https://reader031.vdocuments.net/reader031/viewer/2022022013/5b34d6147f8b9aec518c9998/html5/thumbnails/15.jpg)
Acreditación/Accreditation nº 56/LE156 Anexo Técnico Rev. /Technical Annex Ed.22
Fecha/Date 27/11/2015 Hoja/Page 15 de 25
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Alargamiento
Elongation
UNE-EN 13341:2005 +A1:2011 Apdo. B.6.1
Deformación
Deformation
UNE-EN 13341:2005+A1:2011 Apdo. B.6.2
Resistencia a la presión
Pressure resistance
UNE-EN 13341:2005 +A1:2011 Apdo. B.7
Estanqueidad
Leak test
UNE-EN 13341:2005+A1:2011 Apdo. B.8
Tanques termoplásticos fijos para almacenamiento en superficie de gasóleos domésticos de calefacción, queroseno y combustibles diesel Tanques de poliamida 6 fabricados por polimerización aniónica.
Thermoplastics static tanks for above ground storage of domestic heating oils, kerosene and diesel fuels. polyamide 6 by anionic polymerization tanks.
Propiedades en tracción Fuerza: (0,02 N- 250 kN) Alargamiento: (10 mm -500mm)
Tensile properties Force: (0,02 N- 250 kN) Elongation: (10 mm -500mm)
UNE-EN 13341:2005 +A1:2011 Apdo. A.3.1 UNE-EN ISO 527-2:2012
Resistencia a los carburantes
Oils resistance
UNE-EN 13341:2005 +A1:2011 Apdo. A.3.2 UNE-EN ISO 527-2:2012 UNE-EN ISO 175: 2011
Exudación del color
Colour exudation
UNE-EN 13341:2005 +A1:2011 Apdo. A.3.3
Capacidad
Capacity
UNE-EN 13341:2005 +A1:2011 Apdo. B.1
Aspecto visual Appearance
UNE-EN 13341:2005 +A1:2011 Apdo. B.2
Masa
Mass
(0 - 3000 kg)
UNE-EN 13341:2005 +A1:2011 Apdo. B.3
Espesor de pared
Wall thickness
UNE-EN 13341:2005+A1:2011 Apdo. B.4
Resistencia al impacto
Impact resistance
UNE-EN 13341:2005+A1:2011 Apdo. B.5
Código Validación Electrónica: 1CKAg415A7JL1a2hA9
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
![Page 16: y: AIMPLAS. INSTITUTO TECNOLÓGICO DEL PLÁSTICO · Contenido en negro de carbono en poliolefinas y sus ... Contenido en fibra de vidrio ... La vigencia de la acreditación y del](https://reader031.vdocuments.net/reader031/viewer/2022022013/5b34d6147f8b9aec518c9998/html5/thumbnails/16.jpg)
Acreditación/Accreditation nº 56/LE156 Anexo Técnico Rev. /Technical Annex Ed.22
Fecha/Date 27/11/2015 Hoja/Page 16 de 25
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Alargamiento
Elongation
UNE-EN 13341:2005+A1:2011 Apdo. B.9 and B.6.1
Resistencia a la presión
Pressure resistance
UNE-EN 13341:2005 +A1:2011 Apdo. B.7
Estanqueidad
Watertightness
UNE-EN 13341:2005 +A1:2011 Apdo. B.8
Depósitos, aéreos o en fosa, de plástico reforzado con fibra de vidrio destinados a almacenar productos petrolíferos (fabricados en poliéster)
Tanks of glass-reinforced plastics, for the non-pressure storage of liquid petroleum based fuels according to: UNE 53496-1
Dureza Barcol
Barcol hardness
(0 UB - 100 UB)
UNE 53270: 2012
Propiedades en tracción
Tensile properties Force: (0,02 N- 250 kN) Elongation: (10 mm -500mm)
UNE 53496-1: 2007 Apdo. 6.1.2 UNE-EN ISO 527-4:1997 Specimen type 1B-2-3
Propiedades en flexión
Flexural properties
(0,02 N- 250 kN)
UNE 53496-1: 2007 Apdo. 6.1.3 and 7.6.4 UNE-EN ISO 14125:1999 UNE-EN ISO 14125/AC:2002
Resistencia química
Chemical resistance
UNE 53496-1: 2007 Apdo. 7.6.3 UNE 53316: 2012 UNE-EN ISO 14125:1999 UNE-EN ISO 14125/AC:2002
Ensayo de barrera (contenido en fibra de vidrio)
Barrier test (textile glass content)
UNE 53496-1: 2007 Apdo. 7.7 UNE-EN ISO 1172: 1999 Method A. Apdo. 7.1
Código Validación Electrónica: 1CKAg415A7JL1a2hA9
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
![Page 17: y: AIMPLAS. INSTITUTO TECNOLÓGICO DEL PLÁSTICO · Contenido en negro de carbono en poliolefinas y sus ... Contenido en fibra de vidrio ... La vigencia de la acreditación y del](https://reader031.vdocuments.net/reader031/viewer/2022022013/5b34d6147f8b9aec518c9998/html5/thumbnails/17.jpg)
Acreditación/Accreditation nº 56/LE156 Anexo Técnico Rev. /Technical Annex Ed.22
Fecha/Date 27/11/2015 Hoja/Page 17 de 25
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Control de espesor
Thickness
UNE 53496-1: 2007 Apdo. 7.1.1, 7.1.2
Tanques enterrados de plástico reforzados con fibra de vidrio (PRFV). Tanques cilíndricos horizontales para el almacenamiento sin presión de carburantes petrolíferos líquidos. Tanques de una sola pared. (Fabricados en poliéster)
Underground tanks of glass-reinforced plastics (GRP). Horizontal cylindrical tanks for the non-pressure storage of liquid petroleum based fuels. Requirements and test methods for single wall tanks UNE –EN 976-1
Resistencia química
Chemical resistance
UNE-EN 976-1:1998 Apdo. 6.9.2 UNE-EN 976-1:1999 ERRATUM UNE-EN 977:1998
Propiedades en tracción
Tensile properties Force: (0,02 N- 250 kN) Elongation: (10 mm -500mm)
UNE-EN 976-1:1998 Apdo. 6.9.4 UNE-EN 976-1:1999 ERRATUM UNE-EN ISO 527-4:1997 Specimen type1B-2-3
Propiedades en flexión
Flexural properties
(0,02 N- 250 kN)
UNE-EN 976-1:1998 Apdo.6.9.5 UNE-EN 976-1:1999 ERRATUM UNE-EN ISO 14125: 1999 UNE-EN ISO 14125/AC: 2002 UNE-EN ISO 14125/A1: 2011
Control de espesor
Thickness
UNE-EN 976-1:1998 Apdo. 6.2 UNE-EN 976-1:1999 ERRATUM
Depósitos metálicos, para el almacenamiento de productos petrolíferos líquidos (Reparación con resinas de poliéster)
Metallic tanks for the non-pressure storage of liquid petroleum based fuels. Repair with polyester resins.
UNW 53991:2011 IN
Adherencia
Adherence
UNE 53991:2011+1M 2015 Apdo. 8.2 IN Annexe A
Resistencia química de los materiales
Chemical resistance
UNE 53991:2011+1M 2015 Apdo. 8.3 IN Annexe A UNE 53316: 2012
Resistencia mecánica
Mechanical resistance
(0,02 N- 250 kN)
UNE 53991: 2011 IN Apdo. 8 8.4 UNE-EN ISO 14125:1999 UNE-EN ISO 14125/AC:2002 UNE-EN ISO 14125/A1:2011
Código Validación Electrónica: 1CKAg415A7JL1a2hA9
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
![Page 18: y: AIMPLAS. INSTITUTO TECNOLÓGICO DEL PLÁSTICO · Contenido en negro de carbono en poliolefinas y sus ... Contenido en fibra de vidrio ... La vigencia de la acreditación y del](https://reader031.vdocuments.net/reader031/viewer/2022022013/5b34d6147f8b9aec518c9998/html5/thumbnails/18.jpg)
Acreditación/Accreditation nº 56/LE156 Anexo Técnico Rev. /Technical Annex Ed.22
Fecha/Date 27/11/2015 Hoja/Page 18 de 25
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Dureza Barcol
Barcol hardness
(0 UB - 100 UB)
UNE 53991:2011 IN Apdo. 8.5 UNE 53270:2012
Dureza Shore A y D
Shore A and D Hardness Shore A (20-90) Shore D (20-90)
UNE 53991:2011 IN Apdo.8.5 UNE-EN ISO 868:2003
Piscinas prefabricadas de plástico reforzado con fibra de vidrio (PR-FV)
Glass-reinforced plastics prefabricated swimming pools (GRP)
Propiedades de flexión
Flexural properties
(0,02 N- 250 kN)
UNE 53955:2002 EX Apdo.9.2 UNE-EN ISO 14125:1999 UNE-EN ISO 14125/AC:2002 UNE-EN ISO 14125/A1: 2011
Propiedades en tracción Fuerza: (0,02 N- 250 kN)
Alargamiento: (10 mm -500mm) Tensile properties
Force: (0,02 N- 250 kN) Elongation: (10 mm -500mm)
UNE 53955:2002 EX Apdo.9.3 UNE-EN ISO 527-4:1997
Dureza Barcol
Barcol hardness (0 UB - 100 UB)
UNE 53955:2002 EX Apdo.9.5 UNE 53270:2012
Tubos y accesorios termoplásticos
Thermoplastics pipes and fittings
Propiedades en tracción Fuerza: (0,02 N- 250 kN) Alargamiento:(10 mm -500 mm)
Tensile properties Force: (0,02 N- 250 kN) Elongation: (10 mm -500mm)
UNE-EN ISO 6259-1:2002 ISO 6259-3: 2015 ISO 6259-2: 1997
Temperatura de reblandecimiento Vicat (VST) Tª ambiente a 200 ºC
Vicat softening temperature (Room temperature up to 250ºC)
UNE-EN 727:1995
Resistencia a la presión interna a temperatura constante
Resistance to internal pressure at a given temperature
(0 – 100)Bar 20 ºC a 95 ºC
UNE-EN ISO 1167-1:2006 UNE-EN ISO 1167-2:2006
Código Validación Electrónica: 1CKAg415A7JL1a2hA9
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
![Page 19: y: AIMPLAS. INSTITUTO TECNOLÓGICO DEL PLÁSTICO · Contenido en negro de carbono en poliolefinas y sus ... Contenido en fibra de vidrio ... La vigencia de la acreditación y del](https://reader031.vdocuments.net/reader031/viewer/2022022013/5b34d6147f8b9aec518c9998/html5/thumbnails/19.jpg)
Acreditación/Accreditation nº 56/LE156 Anexo Técnico Rev. /Technical Annex Ed.22
Fecha/Date 27/11/2015 Hoja/Page 19 de 25
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Propiedades en compresión
Compressive properties
(0,02 N- 50 kN)
UNE-EN 802:1995
Tiempo de inducción a la oxidación
Oxidation induction time
UNE-EN 728:1997 UNE-EN ISO 11357-6:2013
Dispersión de negro de carbono o pigmento (Método de compresión)
Carbon black or pigment dispersion (compression method)
ISO 18553:2002 ISO 18553:2002/Amd 1:2007
Tubos y accesorios de poli (cloruro de vinilo) para conducción de agua a presión
Plastics piping systems for water supply under pressure according to: UNE-EN 1452-2
Densidad
Density
UNE-EN ISO 1183-1:2013 Método/Method A
Temperatura de reblandecimiento Vicat Tª ambiente a 200 ºC
Vicat softening temperature (Room temperature up to 200°C)
ISO 2507-1:1995
Resistencia a la presión interna a temperatura constante (0 – 100) Bar 20 ºC a 95 ºC
Diámetros: 25, 32, 40, 50, 63, 75, 90, 110 mm Resistance
to internal pressure at a given temperature (0 – 100) Bar 20°C a 95°C Diameters: 25, 32, 40, 50, 63, 75, 90, 110 mm
UNE-EN 1452-2: 2010 Apdo.8.2. UNE-EN ISO 1167-1:2006 UNE-EN ISO 1167-2:2006
Propiedades en tracción Fuerza: (0,02 N- 250 KN) Alargamiento: (10 mm -500 mm)
Tensile properties Force: (0,02 N- 250 kN) Elongation: (10 mm -500mm)
UNE-EN ISO 6259-1 :2002 ISO 6259-2 :1997
Código Validación Electrónica: 1CKAg415A7JL1a2hA9
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
![Page 20: y: AIMPLAS. INSTITUTO TECNOLÓGICO DEL PLÁSTICO · Contenido en negro de carbono en poliolefinas y sus ... Contenido en fibra de vidrio ... La vigencia de la acreditación y del](https://reader031.vdocuments.net/reader031/viewer/2022022013/5b34d6147f8b9aec518c9998/html5/thumbnails/20.jpg)
Acreditación/Accreditation nº 56/LE156 Anexo Técnico Rev. /Technical Annex Ed.22
Fecha/Date 27/11/2015 Hoja/Page 20 de 25
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Sistemas de canalización en materiales plásticos para evacuación de aguas residuales (a baja y alta temperatura) en el interior de la estructura de losa edificios. Poli (cloruro de vinilo) no plastificado (PVC-U) Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Unplasticized poly(vinyl chloride) (PVC-U) according to: UNE-EN 1329-1
Densidad
Density
UNE-EN ISO 1183-1:2013 Método/Method A
Temperatura de reblandecimiento Vicat (VST) Tª ambiente a 200 ºC
Vicat softening temperature (Environment temperature up to 200°C)
UNE-EN 727:1995
Resistencia a la presión interna a temperatura constante (0 – 100) Bar 20 ºC a 95 ºC Diámetros: 32, 40, 50, 63, 75, 90, 110 mm
Resistance to internal pressure at a given temperature (0 – 100) Bar 20°C a 95°C Diameters: 32, 40, 50, 63, 75, 90, 110 mm
UNE-EN 1329-1: 2014 Apdo.4.3 UNE-EN ISO 1167-1:2006 UNE-EN ISO 1167-2:2006
Sistemas de canalización en materiales plásticos para instalaciones de agua caliente y fría Poli(cloruro de vinilo) clorado (PVC-C). Tubos
Plastics piping systems for hot and cold water installations. Chlorinated poly(vinyl chloride) (PVC-C). Pipes. According to: UNE-EN ISO 15877-2
Resistencia a la presión interna a temperatura constante (0 – 100) Bar 20 ºC a 95 ºC Diámetros: 32, 40, 50, 63, 75, 90, 110 mm
Resistance to internal pressure at a given temperature (0 – 100) Bar 20°C a 95°C Diameters: 32, 40, 50, 63, 75, 90, 110 mm
UNE-EN ISO 15877-2:2009 Apdo.7. UNE-EN ISO 15877-2:2009/A1:2011 UNE-EN ISO 1167-1:2006 UNE-EN ISO 1167-2:2006
Temperatura de reblandecimiento Vicat (VST) Tª ambiente a 200 ºC
Vicat softening temperature (Room temperature up to 200°C)
UNE-EN ISO 15877-2:2009 Apdo.8. UNE-EN ISO 15877-2:2009/A1:2011 UNE-EN 727: 1995
Tubos de polietileno PE 32 y PE 40 para microirrigación
Polyethylene pipes PE 32 and PE 40 for irrigation according to: UNE 53367-1 UNE 53367-2
Índice de fluidez en masa (IFM) y en volumen (IFV) Temperatura máx.: 400 ºC (0,1-250) cm
3/10 min
Melt flow index in mass (MFR) and in volume (MVR) Maximum temperature.: 400°C (0,1-250) cm
3/10 min)
UNE-EN ISO 1133-1:2012 UNE-EN ISO 1133-2:2012
Código Validación Electrónica: 1CKAg415A7JL1a2hA9
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
![Page 21: y: AIMPLAS. INSTITUTO TECNOLÓGICO DEL PLÁSTICO · Contenido en negro de carbono en poliolefinas y sus ... Contenido en fibra de vidrio ... La vigencia de la acreditación y del](https://reader031.vdocuments.net/reader031/viewer/2022022013/5b34d6147f8b9aec518c9998/html5/thumbnails/21.jpg)
Acreditación/Accreditation nº 56/LE156 Anexo Técnico Rev. /Technical Annex Ed.22
Fecha/Date 27/11/2015 Hoja/Page 21 de 25
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Propiedades en tracción Fuerza: (0,02 N- 250 kN) Alargamiento: (10 mm -500 mm)
Tensile properties Force: (0,02 N- 250 kN) Elongation: (10 mm -500mm)
UNE-EN ISO 6259-1:2002 ISO 6259-3:2015
Resistencia a la presión interna a temperatura constante (0 – 100) Bar 20 ºC a 95 ºC Diámetros: 16, 25, 32 mm
Resistance to internal pressure at a given temperature (0 – 100) Bar 20°C a 95°C Diameters: 16, 25,32 mm
UNE 53367-1: 2014 (table 3) UNE-EN ISO 1167-1:2006 UNE-EN ISO 1167-2:2006
Tiempo de inducción a la oxidación
Oxidation induction time
UNE 53367-1: 2014 (table 1 y 5) UNE 53367-1: 2014 (table 1 y 4) UNE-EN ISO 11357-6:2013
Dispersión de negro de carbono o pigmento (Método de compresión)
Carbon black or pigment dispersion (compression method)
UNE 53367-1:2014 (table 4 and 5) ISO 18553:2002 ISO 18553:2002/Amd 1:2007
Contenido en negro de carbono en poliolefinas y sus transformados (analizador termogravimétrico)
Carbon black content in polyolefins and their products (thermogravimetric analyzer)
UNE 53367-1:2014 (table 1 and 5) UNE 53375-3:2011
Densidad
Densiy
UNE 53367-1:2014 (table 1 and 5)
UNE-EN ISO 1183-1:2013 Método/Method A
Sistemas de canalizaciones en materiales plásticos para instalaciones de agua caliente y fría. Polipropileno (PP). Tubos.
Indice de fluidez en masa (IFM) y en volumen (IFV) Temperatura máx.: 400ºC
Melt flow index in mass (MFR) and in volume (MVR) Maximum temperature.: 400°C
(0,1-250) cm3/10 min
UNE-EN ISO 1133-1:2012 UNE-EN ISO 1133-2:2012
Código Validación Electrónica: 1CKAg415A7JL1a2hA9
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
![Page 22: y: AIMPLAS. INSTITUTO TECNOLÓGICO DEL PLÁSTICO · Contenido en negro de carbono en poliolefinas y sus ... Contenido en fibra de vidrio ... La vigencia de la acreditación y del](https://reader031.vdocuments.net/reader031/viewer/2022022013/5b34d6147f8b9aec518c9998/html5/thumbnails/22.jpg)
Acreditación/Accreditation nº 56/LE156 Anexo Técnico Rev. /Technical Annex Ed.22
Fecha/Date 27/11/2015 Hoja/Page 22 de 25
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Plastics piping systems for hot and cold water installations. Polypropylene (PP). Pipes according to UNE-EN ISO 15874-2
Resistencia a la presión interna a temperatura constante (0 – 100)Bar 20 ºC a 95 ºC Diámetros: 16, 25, 32, 40, 50, 63, 75, 90, 110 mm
Resistance to internal pressure at a given temperature (0 – 100)Bar 20°C a 95°C Diameters: 16, 25, 32, 40, 50, 63, 75, 90, 110 mm
UNE-EN ISO 15874-2:2013 UNE-EN ISO 15874-2:2004/A1:2007 Apdo.7 UNE-EN ISO 1167-1:2006 UNE-EN ISO 1167-2:2006
Sistemas de canalización para la conducción de agua (PE)
Plastic piping systems for water supply. Polyethylene (PE) according to UNE-EN 12201-1 UNE-EN 12201-2
Índice de fluidez en masa (IFM) y en volumen (IFV) Temperatura máx.: 275 ºC
(0,1-250) cm3/10 min
Melt flow index in mass (MFR) and in volume (MVR) Maximum temperature.: 275ºC (0,1-250) cm
3/10 min
UNE-EN ISO 1133-1:2012
Propiedades en tracción Fuerza: (0,02 N- 250 KN) Alargamiento: (10 mm -500 mm)
Tensile properties Force: (0,02 N- 250 kN) Elongation: (10 mm -500mm)
UNE-EN ISO 6259-1:2002 ISO 6259-3:2015
Resistencia a la presión interna a temperatura constante (0 – 100)Bar 20 ºC a 95 ºC
Diámetros: 16, 25, 32, 40, 50, 63, 75, 90, 110 mm
Resistance to internal pressure at a given temperature (0 – 100)Bar 20°C a 95°C Diameters: 16, 25, 32, 40, 50, 63, 75, 90, 110 mm
UNE-EN 12201-1:2012 (table 2) UNE-EN 12201-2:2012+A1(2014) (Table 3) UNE-EN 12201-2:2003 (Table3) UNE-EN ISO 1167-1:2006 UNE-EN ISO 1167-2:2006
Tiempo de inducción a la oxidación
Oxidation induction time
UNE-EN 12201-1:2012 (Table 1) UNE-EN 12201-2:2012+A1 (2014) (Table 5) UNE-EN ISO 11357-6:2013
Dispersión de negro de carbono o pigmento (Método de compresión)
UNE-EN 12201-1:2012 (table 1) ISO 18553:2002 ISO 18553:2002/Amd 1:2007
Densidad
Density
UNE-EN ISO 1183-1:2013 Método/Method A
Código Validación Electrónica: 1CKAg415A7JL1a2hA9
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
![Page 23: y: AIMPLAS. INSTITUTO TECNOLÓGICO DEL PLÁSTICO · Contenido en negro de carbono en poliolefinas y sus ... Contenido en fibra de vidrio ... La vigencia de la acreditación y del](https://reader031.vdocuments.net/reader031/viewer/2022022013/5b34d6147f8b9aec518c9998/html5/thumbnails/23.jpg)
Acreditación/Accreditation nº 56/LE156 Anexo Técnico Rev. /Technical Annex Ed.22
Fecha/Date 27/11/2015 Hoja/Page 23 de 25
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Poli(cloruro de vinilo) (PVC) reciclado. UNE 53979
Polyvinyl chloride (PVC) recycled according to: UNE 53979
Temperatura de reblandecimiento Vicat (VST)
Tª ambiente a 200 ºC
Vicat softening temperature (Room temperature up to 200°C)
UNE-EN ISO 306:2015
Densidad
Density
UNE-EN ISO 1183-1:2013 Método/Method A
Dureza Shore A y D Shore A (20 – 90) Shore D (20 – 90)
Shore A and D hardness Shore A (20 – 90) Shore D (20 – 90)
UNE-EN ISO 868:2003
Propiedades en tracción Fuerza: (0,02 N- 250 kN) Alargamiento: (10 mm -500 mm)
Tensile properties Force: (0,02 N- 250 kN) Elongation: (10 mm -500mm)
UNE-EN ISO 527-1:2012 UNE-EN ISO 527-2:2012 UNE-EN ISO 527-3:1996
Sistemas de canalización en materiales plásticos para instalaciones de agua caliente y fría. Polibutileno (PB)
UNE-EN ISO 15876-2
Plastics piping systems for hot and cold water installations.
Índice de fluidez en masa (IFM) y en volumen (IFV) Temperatura máx.: 400 ºC
Melt flow index in mass (MFR) and in volume (MVR) Maximum temperature: 400°C
(0,1-250) cm3/10 min
UNE-EN ISO 1133-1:2012 UNE-EN ISO 1133-2:2012
Código Validación Electrónica: 1CKAg415A7JL1a2hA9
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
![Page 24: y: AIMPLAS. INSTITUTO TECNOLÓGICO DEL PLÁSTICO · Contenido en negro de carbono en poliolefinas y sus ... Contenido en fibra de vidrio ... La vigencia de la acreditación y del](https://reader031.vdocuments.net/reader031/viewer/2022022013/5b34d6147f8b9aec518c9998/html5/thumbnails/24.jpg)
Acreditación/Accreditation nº 56/LE156 Anexo Técnico Rev. /Technical Annex Ed.22
Fecha/Date 27/11/2015 Hoja/Page 24 de 25
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Polybutylene (PB) according to: UNE-EN ISO 15876-2 Resistencia a la presión interna a temperatura
constante
Resistance to internal pressure at a given temperature
(0 – 100) Bar 20°C a 95°C
Diámetros: 16, 25, 32, 40, 50, 63, 75, 90, 110 mm
Diameters: 16, 25, 32, 40, 50, 63, 75, 90, 110 mm
UNE-EN ISO 15876-2:2004 Par.7 UNE-EN ISO 15876-2:2004/A1:2007 UNE-EN ISO 15876-3:2004 Par.7 UNE-EN ISO 1167-1:2006 UNE-EN ISO 1167-2:2006
Sistemas de canalización en materiales plásticos para instalaciones de agua caliente y fría. Polietileno reticulado (PE-X)
Plastics piping systems for hot and cold water installations -- Crosslinked polyethylene (PE-X) according to:
UNE-EN ISO 15875-2
Resistencia a la presión interna a temperatura constante
Resistance to internal pressure at a given temperature
(0 – 100) Bar 20 ºC a 95 ºC
Diámetros: 16, 25, 32, 40, 50, 63, 75, 90, 110 mm
Diameters: 16, 25, 32, 40, 50, 63, 75, 90, 110 mm
UNE-EN ISO 15875-2:2004 UNE-EN ISO 15875-2:2004/A1:2007 Aptdo./Par.7 UNE-EN ISO 1167-1:2006 UNE-EN ISO 1167-2:2006
Sistemas de canalización multicapas para instalaciones de agua caliente y fría en el interior de edificios
Multilayer piping systems for hot and cold water installations inside buildings according to:
UNE-EN ISO 21003-5
Resistencia a la presión interna a temperatura constante
Resistance to internal pressure at a given temperature
(0 – 100) Bar 20 ºC a 95 ºC
Diámetros: 16, 25, 32, 40, 50, 63, 75, 90, 110 mm
Diameters: 16, 25, 32, 40, 50, 63, 75, 90, 110 mm
UNE-EN ISO 21003-5:2009 UNE-EN ISO 21003-5:2009 +ERRATUM 2009 UNE-EN ISO 1167-1:2006 UNE-EN ISO 1167-2:2006
Pequeñas instalaciones de depuración de aguas residuales para poblaciones de hasta 50 habitantes equivalentes.
Parte 1: Fosas sépticas prefabricadas (PRFV, PE, PP y PVC-U)
Small wastewater treatment
Eficacia hidráulica
Hydraulic efficiency
UNE-EN 12566-1:2000 Anexo B UNE-EN 12566-1: 2000/A1:2004
Capacidad
Capacity
UNE-EN 12566-1:2000 Apdo.5.4 UNE-EN 12566-1:2000/A1:2004
Estanqueidad al agua
Watertightness
UNE-EN 12566-1:2000 Apdo.5.3
UNE-EN 12566-1:2000/A1:2004
Código Validación Electrónica: 1CKAg415A7JL1a2hA9
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
![Page 25: y: AIMPLAS. INSTITUTO TECNOLÓGICO DEL PLÁSTICO · Contenido en negro de carbono en poliolefinas y sus ... Contenido en fibra de vidrio ... La vigencia de la acreditación y del](https://reader031.vdocuments.net/reader031/viewer/2022022013/5b34d6147f8b9aec518c9998/html5/thumbnails/25.jpg)
Acreditación/Accreditation nº 56/LE156 Anexo Técnico Rev. /Technical Annex Ed.22
Fecha/Date 27/11/2015 Hoja/Page 25 de 25
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
systems for up to 50 PT. Part 1: Prefabricated septic tanks (PRFV,PE,PP,and PVC-U)
Determinación de las características mecánicas de las probetas utilizadas para el cálculo del comportamiento estructural
Determination of the mechanical properties of the specimens used in structural behaviour calculation
UNE-EN 12566-1: 2000/A1:2004 Annex D Par.D.4.2 UNE-EN ISO 14125:1999 UNE-EN ISO 14125/AC:2002
UNE-EN ISO 14125/A1:2011
Pequeñas instalaciones de depuración de aguas residuales para poblaciones de hasta 50 habitantes equivalentes.
Parte 3: Plantas de depuración de aguas residuales domésticas prefabricadas y/o montadas en su destino (PRFV, PE, PP y PVC-U)
Part 3: Packaged and/or site assembled domestic wastewater treatment plants (PRFV,PE,PP,and PVC-U)
Estanqueidad al agua
Watertightness
UNE-EN 12566-3: 2006+A2:2014 Annex A.2
Determinación de las características mecánicas de las probetas utilizadas para el cálculo del comportamiento estructural
Determination of the mechanical properties of the specimens used in structural behaviour calculation
UNE-EN 12566-3:2006+A2:2014 Annex C Apdo. C.4.2 and C.4.4 UNE-EN ISO 14125:1999 UNE-EN ISO 14125/AC:2002 UNE-EN ISO 14125/A1:2011 UNE-EN ISO 178: 2011
Código Validación Electrónica: 1CKAg415A7JL1a2hA9
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí