yatender prajapati shubham agarwal deeksha bisht anupama singh
TRANSCRIPT
Final Year Project Presentation.
RepresentBy-
Yatender PrajapatiShubham Agarwal
Deeksha Bisht Anupama Singh
ADVANCE OFFICE AUTOMATION
Office automation refers to the varied computer machinery and software used to digitally create, collect, store, manipulate, and relay office information needed for accomplishing basic tasks and goals. Raw data storage, electronic transfer, and the management of electronic business information comprise the basic activities of an office automation system. Office Automation helps to optimized or automate existing office procedures.
ADVANCE OFFICE AUTOMATION
This is a very unique project in this we are design a smart conference room, in which are constructing a circuit, in which circuit work.
Objective Count the number of person going inside and reducing
the counting when person exits.
INTRODUCTION
It controls the power system, when nobody present in the hall or LCD displays zero person, it switch off the power .When a person enters the hall or LCD displays 1, it switch on the power.
It controls the conference room temperature. When temperature is less than 20 degree heater start, if temperature is in between 20-30 degree fan start , when temp. more than 30 A/C will get on.
INTRODUCTION CONTD..
A primary method for counting the visitors involves hiring human auditors to stand and manually tally the number of visitors who pass by a certain location. Here is a low-cost microcontroller based visitor counter that can be used to know the number of persons at a place. Two IR transmitter-receiver pairs are used at the passage: one pair comprising IR transmitter IR TX1 and receiver phototransistor T1 is installed at the entry point of the passage, while the other pair comprising IR transmitter IR TX2 and phototransistor T2 is installed at the exit of the passage.
Working of Counter
COUNTER CIRCUIT DIAGRAM
Components
SW1 = Switch (Toggle) R1 = 10k ohm
R2 = 10k ohm R3 = 56k ohm
R4 = 10k ohm R5 = R13 = LDR
R6 = 2200 ohm R7 = 2200ohm
R8 = R9 = 10k ohm R10 = 10k ohm
R11 = 4700 ohm R12 = 56k ohm
R14 = 4700 ohm R15 = 10k ohm
C1 = 470µF C2 = 10µF
C3 = 2.2µF C4 = 10µF
C5 = 2.2µF IC 40110 Counter (Maplin)
IC = 555 Timer Resistor Block = 1k ohms
Reset Switch = (PTM) Dual LCD display (Package 86)
Transistor = BC108.
This temperature control application reads a value from a temperature sensor and determines when to switch A/C , Heater or fan on according to minimum and maximum temperature limit settings. These settings can be changed using upper and lower limit set switches. The limit settings and the current temperature are displayed on LCD panel.
Working of Temperature Control
Working of Temperature Control CONTD..
Fig: Hardware Block Diagram of an
Automatic Temperature Control System Using RZK
FAN
HEATER
Temperature sensor
LCD display
MCU
SW1
SW2
SW3 AC
It controls the power system, when a person enters the
room, it switch ON the power and LCD displays the counter.
When nobody present in the hall or LCD displays counter person, it switch off the power.
Working of power control and saving
Circuit Diagram
Two pair of IR sensor Microcontroller AT89S52 Temp. Sensor lm35 IC 555 Power Supply Transistor Resistance Diode Capacitors Regulater-7805 Transformer
Components used in Project:
Need to improve office productivity. Large number of organizations are being benefitted
by office automation due to the following advantages related to the human resource information system.
Better utilization of human resources Improved quality of work Efficient decision Better service for customers. Immediately update business information
ADVANTAGES
It provide information to management on the volume and flow of people throughout a location A primary method for counting the visitors involves hiring human auditors to stand and manually tally the number of visitors who pass by a certain location.
It can also replaces CARD PUNCHING machine in an Industry. Temperature Sensor automatically switch ON the
devices(heater/fan/AC) according to the room temperature. This temperature control application reads a value from a temperature sensor and determines when to switch a fan or bulb off or on according to minimum and maximum temperature limit settings.
It saves power in any particular room. When nobody present in the hall ,it switch off the power.
APPLICATIONS
It saves power in any room. When nobody present in the hall ,it switch off the power. Thus saves the power.
It reduces the manual work by automatic switching of AC/Fan/Heater.
It improves the work efficiency.
CONCLUSION
BIBLIOGRAPHY www.nationalstemcentre.org www.zilog.com www.labguru.com www.fadooengineers.com
THANK YOU!!!