yzf-r1 - fuelarc.com · as the owner of the yzf-r1, you are benefiting from yamaha’s vast...
TRANSCRIPT
DIC183
YZF-R1
OWNER’S MANUAL
Read this manual carefully before operating this vehicle.
2SG-28199-E0
[English (E)]
EAU50921
ay with this vehicle if it is sold.
U2SGE0E0.book Page 1 Wednesday, June 12, 2013 1:15 PM
Read thi
General
Date of is
Place of i
CompanyWe
Address:
Kind of eHereby d
Type-des
is in comR&TTE EN300 33EN60950Two or T
123
4
VTv
Revision No. C
T
s manual carefully before operating this vehicle. This manual should st
manager of quality assurance div.
sue: 1 Aug. 2002
ssue: Shizuoka, Japan
DECLARATION of CONFORMITY
YAMAHA MOTOR ELECTRONICS CO., LTD.1450-6, Mori, Mori-machi, Shuchi-gun, Shizuoka-ken, 437-0292 Japan
: YAMAHA MOTOR ELECTRONICS CO., LTD. 1450-6, Mori, Mori-Machi, Shuchi-gun, Shizuoka-Ken, 437-0292 Japan
quipment: IMMOBILIZEReclare that the product:
ignation: 5SL-00
pliance with following norm(s) or documents:Directive(1999/5/EC)0-2 v1.3.1(2006-01), EN300 330-2 v1.5.1(2010-02)-1:2006/A11:2009hree-Wheel Motor Vehicles Directive(97/24/EC: Chapter 8, EMC)
ersion up the norm of EN60950 to EN60950-1 o change company nameersion up of the following norm:• EN300 330-2 v1.1.1 to EN300 330-2 v1.3.1 and EN300 330-2 v1.5.1• EN60950-1:2001 to EN60950-1:2006/A11:2009
27 Feb. 20061 Mar. 2007
8 Jul. 2010
recordontentso change contact person and integrate type-designation.
Date9 Jun. 2005
INTRODUCTION
EAU10103
Welcome to the Yamaha world of motorcycling!As the owner of the YZF-R1, you are benefiting from Yamaha’s vast experience and newest technology regarding the de-sign and manufacture of high-quality products, which have earned Yamaha a reputation for dependability.Please take the time to read this manual thoroughly, so as to enjoy all advantages of your YZF-R1. The Owner’s Manualdoes not only instruct you in how to operate, inspect and maintain your motorcycle, but also in how to safeguard yourselfand others from trouble and injury.In addition, the many tips given in this manual will help keep your motorcycle in the best possible condition. If you have anyfurther questions, do not hesitate to contact your Yamaha dealer.The Yamaha team wishes you many safe and pleasant rides. So, remember to put safety first!Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most cur-rent product information available at the time of printing, there may be minor discrepancies between your motorcycle andthis manual. If there is any question concerning this manual, please consult a Yamaha dealer.
WARNING
EWA10032
Please read this manual carefully and completely before operating this motorcycle.
U2SGE0E0.book Page 1 Wednesday, June 12, 2013 1:15 PM
IM
EAU10134
Pa ions:
*P
to potential personal injury ymbol to avoid possible injury
if not avoided, could result in
e taken to avoid damage to the
ier or clearer.
N
T
U2SGE0E0.book Page 1 Wednesday, June 12, 2013 1:15 PM
PORTANT MANUAL INFORMATION
rticularly important information is distinguished in this manual by the following notat
roduct and specifications are subject to change without notice.
This is the safety alert symbol. It is used to alert youhazards. Obey all safety messages that follow this sor death.
A WARNING indicates a hazardous situation which,death or serious injury.
A NOTICE indicates special precautions that must bvehicle or other property.
A TIP provides key information to make procedures eas
WARNING
OTICE
IP
UAL INFORMATION
U2SGE0E0.book Page 2 Wednesday, June 12, 2013 1:15 PM
IMPORTANT MAN
EAU10201
YZF-R1OWNER’S MANUAL
©2013 by Yamaha Motor Co., Ltd.1st edition, May 2013
All rights reserved.Any reprinting or unauthorized use without the written permission of
Yamaha Motor Co., Ltd. is expressly prohibited.
Printed in Japan.
hecking the engine idling speed ........................................ 6-17hecking the throttle grip free play............................................ 6-18
alve clearance............................. 6-18ires .............................................. 6-18ast wheels .................................. 6-21djusting the clutch lever free play............................................ 6-21hecking the brake lever free play............................................ 6-22rake light switches ..................... 6-23hecking the front and rear brake pads .......................................... 6-23hecking the brake fluid level ...... 6-24hanging the brake fluid .............. 6-25rive chain slack........................... 6-25leaning and lubricating the drive chain.......................................... 6-27hecking and lubricating the cables........................................ 6-27hecking and lubricating the throttle grip and cable ............... 6-28hecking and lubricating the brake and shift pedals............... 6-28hecking and lubricating the brake and clutch levers ............. 6-29hecking and lubricating the sidestand................................... 6-29
ubricating the swingarm pivots......................................... 6-30
U2SGE0E0.book Page 1 Wednesday, June 12, 2013 1:15 PM
TA
SA
DE
LRC
INS
FU
IMI
MDHCSBBTFFF
CSHSRR
BLE OF CONTENTS
FETY INFORMATION .................. 1-1
SCRIPTION .................................. 2-1eft view ......................................... 2-1ight view....................................... 2-2ontrols and instruments ............... 2-3
TRUMENT AND CONTROL
NCTIONS ...................................... 3-1mmobilizer system......................... 3-1
ain switch/steering lock............... 3-2ndicator lights and warning
lights............................................ 3-4ulti-function meter unit ................ 3-8-mode (drive mode).................... 3-18andlebar switches...................... 3-18lutch lever .................................. 3-20hift pedal .................................... 3-21rake lever.................................... 3-21rake pedal .................................. 3-22raction control system................ 3-22uel tank cap................................ 3-24uel............................................... 3-25uel tank breather hose and overflow hose............................ 3-26atalytic converter ....................... 3-27eats ............................................ 3-27elmet holder ............................... 3-29torage compartment .................. 3-29ider footrest position.................. 3-30ear view mirrors.......................... 3-30
Adjusting the front fork .................3-31Adjusting the shock absorber
assembly....................................3-33Luggage strap holders ..................3-35Sidestand ......................................3-35Ignition circuit cut-off system .......3-36
FOR YOUR SAFETY –
PRE-OPERATION CHECKS .............4-1
OPERATION AND IMPORTANT
RIDING POINTS ................................5-1Starting the engine..........................5-1Shifting ............................................5-2Tips for reducing fuel
consumption................................5-3Engine break-in ...............................5-3Parking ............................................5-4
PERIODIC MAINTENANCE AND
ADJUSTMENT...................................6-1Owner’s tool kit ...............................6-2Periodic maintenance chart for the
emission control system..............6-3General maintenance and
lubrication chart...........................6-4Removing and installing cowlings...6-8Checking the spark plugs .............6-10Engine oil and oil filter cartridge....6-11Coolant..........................................6-14Air filter element ............................6-17
C
C
VTCA
C
BC
CCDC
C
C
C
C
C
L
BLE OF CONTENTS
M
S
S
C
U2SGE0E0.book Page 2 Wednesday, June 12, 2013 1:15 PM
TA
Checking the front fork..................6-30Checking the steering ...................6-31Checking the wheel bearings ........6-31Battery ...........................................6-32Replacing the fuses.......................6-33Replacing a headlight bulb............6-35Tail/brake light...............................6-36Replacing a turn signal light
bulb ............................................6-36Replacing the license plate light
bulb ............................................6-37Auxiliary light .................................6-38Supporting the motorcycle............6-38Troubleshooting ............................6-39Troubleshooting charts .................6-40
OTORCYCLE CARE AND
TORAGE ..........................................7-1Matte color caution .........................7-1Care.................................................7-1Storage............................................7-4
PECIFICATIONS..............................8-1
ONSUMER INFORMATION ............9-1Identification numbers.....................9-1
1
pears to be very effective in reduc-ing the chance of this type ofaccident.Therefore:
• Wear a brightly colored jacket.• Use extra caution when you are
approaching and passingthrough intersections, since in-tersections are the most likelyplaces for motorcycle accidentsto occur.
• Ride where other motorists cansee you. Avoid riding in anothermotorist’s blind spot.
• Never maintain a motorcyclewithout proper knowledge.Contact an authorized motorcy-cle dealer to inform you on ba-sic motorcycle maintenance.Certain maintenance can onlybe carried out by certified staff.
U2SGE0E0.book Page 1 Wednesday, June 12, 2013 1:15 PM
Be
AsspatioMoThpetectheknoforHe
1-1
SAFETY INFORMATION
EAU1028B
a Responsible Owner
the vehicle’s owner, you are re-onsible for the safe and proper oper-n of your motorcycle.torcycles are single-track vehicles.
eir safe use and operation are de-ndent upon the use of proper ridinghniques as well as the expertise of operator. Every operator shouldw the following requirements be-
e riding this motorcycle. or she should:
Obtain thorough instructions froma competent source on all aspectsof motorcycle operation.Observe the warnings and mainte-nance requirements in this Own-er’s Manual.Obtain qualified training in safeand proper riding techniques.Obtain professional technical ser-vice as indicated in this Owner’sManual and/or when made neces-sary by mechanical conditions.
Never operate a motorcycle with-out proper training or instruction.Take a training course. Beginnersshould receive training from a cer-tified instructor. Contact an autho-rized motorcycle dealer to find outabout the training courses nearestyou.
Safe Riding
Perform the pre-operation checkseach time you use the vehicle to makesure it is in safe operating condition.Failure to inspect or maintain the vehi-cle properly increases the possibility ofan accident or equipment damage.See page 4-1 for a list of pre-operationchecks. This motorcycle is designed to
carry the operator and a passen-ger.
The failure of motorists to detectand recognize motorcycles in traf-fic is the predominating cause ofautomobile/motorcycle accidents.Many accidents have beencaused by an automobile driverwho did not see the motorcycle.Making yourself conspicuous ap-
FETY INFORMATION
1
otective Apparel
e majority of fatalities from motorcy- accidents are the result of head in-ies. The use of a safety helmet is thegle most critical factor in the pre-ntion or reduction of head injuries.
Always wear an approved helmet.Wear a face shield or goggles.Wind in your unprotected eyescould contribute to an impairmentof vision that could delay seeing ahazard.The use of a jacket, heavy boots,trousers, gloves, etc., is effectivein preventing or reducing abra-sions or lacerations.Never wear loose-fitting clothes,otherwise they could catch on thecontrol levers, footrests, or wheelsand cause injury or an accident.Always wear protective clothingthat covers your legs, ankles, andfeet. The engine or exhaust sys-tem become very hot during or af-ter operation and can causeburns.A passenger should also observethe above precautions.
U2SGE0E0.book Page 2 Wednesday, June 12, 2013 1:15 PM
SA
1-2
Many accidents involve inexperi-enced operators. In fact, many op-erators who have been involved inaccidents do not even have a cur-rent motorcycle license.• Make sure that you are qualified
and that you only lend your mo-torcycle to other qualified oper-ators.
• Know your skills and limits.Staying within your limits mayhelp you to avoid an accident.
• We recommend that you prac-tice riding your motorcyclewhere there is no traffic until youhave become thoroughly famil-iar with the motorcycle and all ofits controls.
Many accidents have beencaused by error of the motorcycleoperator. A typical error made bythe operator is veering wide on aturn due to excessive speed or un-dercornering (insufficient lean an-gle for the speed).• Always obey the speed limit and
never travel faster than warrant-ed by road and traffic condi-tions.
• Always signal before turning orchanging lanes. Make sure thatother motorists can see you.
The posture of the operator andpassenger is important for propercontrol.• The operator should keep both
hands on the handlebar andboth feet on the operator foot-rests during operation to main-tain control of the motorcycle.
• The passenger should alwayshold onto the operator, the seatstrap or grab bar, if equipped,with both hands and keep bothfeet on the passenger footrests.Never carry a passenger unlesshe or she can firmly place bothfeet on the passenger footrests.
Never ride under the influence ofalcohol or other drugs.
This motorcycle is designed foron-road use only. It is not suitablefor off-road use.
Pr
Thclejursinve
1
Av
AlmcaaccoCalesenenboyoabelshovesysofreM
en loading within this weight limit,p the following in mind:Cargo and accessory weightshould be kept as low and close tothe motorcycle as possible. Se-curely pack your heaviest items asclose to the center of the vehicleas possible and make sure to dis-tribute the weight as evenly aspossible on both sides of the mo-torcycle to minimize imbalance orinstability.Shifting weights can create a sud-den imbalance. Make sure thataccessories and cargo are se-curely attached to the motorcyclebefore riding. Check accessorymounts and cargo restraints fre-quently.• Properly adjust the suspension
for your load (suspension-ad-justable models only), andcheck the condition and pres-sure of your tires.
• Never attach any large or heavyitems to the handlebar, frontfork, or front fender. Theseitems, including such cargo assleeping bags, duffel bags, or
U2SGE0E0.book Page 3 Wednesday, June 12, 2013 1:15 PM
SAFETY INFORMATION
1-3
oid Carbon Monoxide Poisoning
l engine exhaust contains carbononoxide, a deadly gas. Breathingrbon monoxide can cause head-hes, dizziness, drowsiness, nausea,nfusion, and eventually death.rbon Monoxide is a colorless, odor-s, tasteless gas which may be pres-t even if you do not see or smell anygine exhaust. Deadly levels of car-n monoxide can collect rapidly andu can quickly be overcome and un-le to save yourself. Also, deadly lev- of carbon monoxide can linger forurs or days in enclosed or poorlyntilated areas. If you experience anymptoms of carbon monoxide poi-ning, leave the area immediately, getsh air, and SEEK MEDICAL TREAT-ENT.
Do not run engine indoors. Even ifyou try to ventilate engine exhaustwith fans or open windows anddoors, carbon monoxide can rap-idly reach dangerous levels.Do not run engine in poorly venti-lated or partially enclosed areassuch as barns, garages, or car-ports.
Do not run engine outdoors whereengine exhaust can be drawn intoa building through openings suchas windows and doors.
Loading
Adding accessories or cargo to yourmotorcycle can adversely affect stabil-ity and handling if the weight distribu-tion of the motorcycle is changed. Toavoid the possibility of an accident, useextreme caution when adding cargo oraccessories to your motorcycle. Useextra care when riding a motorcyclethat has added cargo or accessories.Here, along with the information aboutaccessories below, are some generalguidelines to follow if loading cargo toyour motorcycle:The total weight of the operator, pas-senger, accessories and cargo mustnot exceed the maximum load limit.Operation of an overloaded vehicle
could cause an accident.
Whkee
Maximum load:189 kg (417 lb)
FETY INFORMATION
1
G
CisYabbMtocfoathTdcmmin
steering travel or control opera-tion, or obscure lights or reflec-tors.• Accessories fitted to the han-
dlebar or the front fork area cancreate instability due to improp-er weight distribution or aerody-namic changes. If accessoriesare added to the handlebar orfront fork area, they must be aslightweight as possible andshould be kept to a minimum.
• Bulky or large accessories mayseriously affect the stability ofthe motorcycle due to aerody-namic effects. Wind may at-tempt to lift the motorcycle, orthe motorcycle may becomeunstable in cross winds. Theseaccessories may also cause in-stability when passing or beingpassed by large vehicles.
• Certain accessories can dis-place the operator from his orher normal riding position. Thisimproper position limits thefreedom of movement of the
U2SGE0E0.book Page 4 Wednesday, June 12, 2013 1:15 PM
SA
1-4
tents, can create unstable han-dling or a slow steering re-sponse.
This vehicle is not designed to
pull a trailer or to be attached to
a sidecar.
enuine Yamaha Accessories
hoosing accessories for your vehicle an important decision. Genuineamaha accessories, which are avail-ble only from a Yamaha dealer, haveeen designed, tested, and approvedy Yamaha for use on your vehicle.any companies with no connection Yamaha manufacture parts and ac-
essories or offer other modificationsr Yamaha vehicles. Yamaha is not in
position to test the products thatese aftermarket companies produce.
herefore, Yamaha can neither en-orse nor recommend the use of ac-essories not sold by Yamaha orodifications not specifically recom-ended by Yamaha, even if sold andstalled by a Yamaha dealer.
Aftermarket Parts, Accessories, and
Modifications
While you may find aftermarket prod-ucts similar in design and quality togenuine Yamaha accessories, recog-nize that some aftermarket accesso-ries or modifications are not suitablebecause of potential safety hazards toyou or others. Installing aftermarketproducts or having other modificationsperformed to your vehicle that changeany of the vehicle’s design or operationcharacteristics can put you and othersat greater risk of serious injury ordeath. You are responsible for injuriesrelated to changes in the vehicle.Keep the following guidelines in mind,as well as those provided under “Load-ing” when mounting accessories. Never install accessories or carry
cargo that would impair the per-formance of your motorcycle.Carefully inspect the accessorybefore using it to make sure that itdoes not in any way reduceground clearance or corneringclearance, limit suspension travel,
1
Af
Thmthprdltirm6-fo
Tr
Betiocle
U2SGE0E0.book Page 5 Wednesday, June 12, 2013 1:15 PM
SAFETY INFORMATION
1-5
operator and may limit controlability, therefore, such accesso-ries are not recommended.
Use caution when adding electri-cal accessories. If electrical ac-cessories exceed the capacity ofthe motorcycle’s electrical sys-tem, an electric failure could re-sult, which could cause adangerous loss of lights or enginepower.
termarket Tires and Rims
e tires and rims that came with yourotorcycle were designed to matche performance capabilities and toovide the best combination of han-ing, braking, and comfort. Otheres, rims, sizes, and combinationsay not be appropriate. Refer to page18 for tire specifications and more in-rmation on replacing your tires.
ansporting the Motorcycle
sure to observe following instruc-ns before transporting the motorcy- in another vehicle.
Remove all loose items from themotorcycle.
Check that the fuel cock (ifequipped) is in the “OFF” positionand that there are no fuel leaks.
Point the front wheel straightahead on the trailer or in the truckbed, and choke it in a rail to pre-vent movement.
Shift the transmission in gear (formodels with a manual transmis-sion).
Secure the motorcycle with tie-downs or suitable straps that areattached to solid parts of the mo-torcycle, such as the frame or up-per front fork triple clamp (and not,for example, to rubber-mountedhandlebars or turn signals, orparts that could break). Choosethe location for the straps carefullyso the straps will not rub againstpainted surfaces during transport.
The suspension should be com-pressed somewhat by the tie-downs, if possible, so that the mo-torcycle will not bounce exces-sively during transport.
DESCRIPTION
2
EAU10411
L
1.2.3.4.5.6.7.
compression damping force adjusting bolt ping) (page 3-33)
spring preload adjusting screw (page 3-33) rebound damping force adjusting screw
6-11)-15)
page 6-11)
U2SGE0E0.book Page 1 Wednesday, June 12, 2013 1:15 PM
2-1
eft view
1,2 3 4,5,6
13 12 11 10 7,89Front fork spring preload adjusting bolt (page 3-31)Front fork compression damping force adjusting screw (page 3-31)Coolant reservoir (page 6-14)Fuel injection system fuse (page 6-33)Main fuse (page 6-33)Fuse box (page 6-33)Shock absorber assembly compression damping force adjusting bolt (for fast compression damping) (page 3-33)
8. Shock absorber assembly(for slow compression dam
9. Shock absorber assembly10.Shock absorber assembly
(page 3-33)11.Engine oil drain bolt (page12.Coolant drain bolt (page 613.Engine oil filter cartridge (
D
2
EAU10421
R
9
1.2.3.4.5.6.7.8.
-11)ow (page 6-11)ge 6-23)page 6-24)
U2SGE0E0.book Page 2 Wednesday, June 12, 2013 1:15 PM
ESCRIPTION
2-2
ight view
1,2,3 4 5,6 7 8
10111213Storage compartment (page 3-29)Luggage strap holder (page 3-35)Helmet holder (page 3-29)Seat lock (page 3-27)Battery (page 6-32)Owner’s tool kit (page 6-2)Fuel tank cap (page 3-24)Front fork rebound damping force adjusting screw (page 3-31)
9. Radiator cap (page 6-14)10.Engine oil filler cap (page 611.Engine oil level check wind12.Rear brake light switch (pa13.Rear brake fluid reservoir (
DESCRIPTION
2
EAU10431
C
8 9
1.2.3.4.5.6.7.8.
U2SGE0E0.book Page 3 Wednesday, June 12, 2013 1:15 PM
2-3
ontrols and instruments
1 2 3 65 74
Clutch lever (page 3-20)Left handlebar switches (page 3-18)Main switch/steering lock (page 3-2)Multi-function meter unit (page 3-8)Hazard switch (page 3-19)Front brake fluid reservoir (page 6-24)Right handlebar switches (page 3-18)Throttle grip (page 6-18)
9. Brake lever (page 3-21)
IN
3
Im
Thbirekelo
mended to use either standard
key and keep the code re-regis-
tering key in a safe place.
Do not submerse any key in wa-
ter.
Do not expose any key to exces-
sively high temperatures.
Do not place any key close to
magnets (this includes, but not
limited to, products such as
speakers, etc.).
Do not place items that transmit
electrical signals close to any
key.
Do not place heavy items on any
key.
Do not grind any key or alter its
shape.
Do not disassemble the plastic
part of any key.
Do not put two keys of any im-
mobilizer system on the same
key ring.
Keep the standard keys as well
as keys of other immobilizer
systems away from this vehi-
cle’s code re-registering key.
1.2.
U2SGE0E0.book Page 1 Wednesday, June 12, 2013 1:15 PM
STRUMENT AND CONTROL FUNCTIONS
3-1
EAU10978
mobilizer system
is vehicle is equipped with an immo-lizer system to help prevent theft by-registering codes in the standardys. This system consists of the fol-wing:
a code re-registering key (with ared bow)two standard keys (with a blackbow) that can be re-registeredwith new codesa transponder (which is installed inthe code re-registering key)an immobilizer unitan ECU
an immobilizer system indicatorlight (See page 3-8.)
The key with the red bow is used toregister codes in each standard key.Since re-registering is a difficult pro-cess, take the vehicle along with allthree keys to a Yamaha dealer to havethem re-registered. Do not use the keywith the red bow for driving. It shouldonly be used for re-registering thestandard keys. Always use a standardkey for driving.
NOTICEECA11822
DO NOT LOSE THE CODE RE-
REGISTERING KEY! CONTACT
YOUR DEALER IMMEDIATELY
IF IT IS LOST! If the code re-reg-
istering key is lost, registering
new codes in the standard keys
is impossible. The standard
keys can still be used to start
the vehicle, however if code re-
registering is required (i.e., if a
new standard key is made or all
keys are lost) the entire immobi-
lizer system must be replaced.
Therefore, it is highly recom-
Code re-registering key (red bow)Standard keys (black bow)
NTROL FUNCTIONS
3
EAU10551
electrical circuits are supplied withwer, the meter lighting, taillight, li-nse plate light and auxiliary lightsme on, and the engine can be start-. The key cannot be removed.
e headlights come on automaticallyen the engine is started and stay ontil the key is turned to “OFF”, even if engine stalls.
EAU10662
F
electrical systems are off. The keyn be removed.
WARNING
EWA10062
ver turn the key to “OFF” or
OCK” while the vehicle is moving.
herwise the electrical systems will
switched off, which may result in
s of control or an accident.
U2SGE0E0.book Page 2 Wednesday, June 12, 2013 1:15 PM
INSTRUMENT AND CO
3-2
Keep other immobilizer system
keys away from the main switch
as they may cause signal inter-
ference.
EAU10473
Main switch/steering lock
The main switch/steering lock controlsthe ignition and lighting systems, and isused to lock the steering. The variouspositions are described below.
TIP
Be sure to use the standard key (blackbow) for regular use of the vehicle. Tominimize the risk of losing the code re-registering key (red bow), keep it in asafe place and only use it for code re-registering.
ON
Allpocecoed
TIP
Thwhunthe
OF
Allca
Ne
“L
Ot
be
los
P
ONOFF
LOCK
IN
3
LO
Thsym
To
1
2
3
TICEECA11021
not use the parking position for
extended length of time, other-
e the battery may discharge.
1.2.
U2SGE0E0.book Page 3 Wednesday, June 12, 2013 1:15 PM
STRUMENT AND CONTROL FUNCTIONS
3-3
EAU10685
CK
e steering is locked, and all electricalstems are off. The key can be re-oved.
lock the steering
. Turn the handlebars all the way tothe left.
. Push the key in from the “OFF”position, and then turn it to“LOCK” while still pushing it.
. Remove the key.
To unlock the steering
Push the key in, and then turn it to“OFF” while still pushing it.
EAU10942
(Parking)
The steering is locked, and the taillight,license plate light and auxiliary lightsare on. The hazard lights and turn sig-nal lights can be turned on, but all otherelectrical systems are off. The key canbe removed.The steering must be locked before thekey can be turned to “ ”.
NO
Do
an
wis
Push.Turn.
1 2
1. Push.2. Turn.
1 2
NTROL FUNCTIONS
3
Inli
he warning light does not come onially when the key is turned to “ON”,if the warning light remains on, haveamaha dealer check the electrical
cuit.
Even if the oil level is sufficient, thewarning light may flicker when rid-ing on a slope or during suddenacceleration or deceleration, butthis is not a malfunction.This model is also equipped with aself-diagnosis device for the oillevel detection circuit. If a problemis detected in the oil level detec-tion circuit, the following cycle willbe repeated until the malfunctionis corrected: The oil level warninglight will flash ten times, then gooff for 2.5 seconds. If this occurs,have a Yamaha dealer check thevehicle.
EAU11367
el level warning light “ ”
is warning light comes on when thel level drops below approximately L (0.82 US gal, 0.68 Imp.gal). When
s occurs, refuel as soon as possible.
1.2.3.4.5.
6.7.8.9.1011
U2SGE0E0.book Page 4 Wednesday, June 12, 2013 1:15 PM
INSTRUMENT AND CO
3-4
EAU49394
dicator lights and warning ghts
EAU11031
Turn signal indicator lights “ ”
and “ ”
The corresponding indicator lightflashes when the turn signal switch ispushed to the left or right.
EAU11061
Neutral indicator light “ ”
This indicator light comes on when thetransmission is in the neutral position.
EAU11081
High beam indicator light “ ”
This indicator light comes on when thehigh beam of the headlight is switchedon.
EAU11255
Oil level warning light “ ”
This warning light comes on if the en-gine oil level is low.The electrical circuit of the warninglight can be checked by turning the keyto “ON”. The warning light shouldcome on for a few seconds, and thengo off.
If tinitor a Ycir
TIP
Fu
Thfue3.1thi
Shift timing indicator lightEngine trouble warning light “ ”Oil level warning light “ ”Coolant temperature warning light “ ”Traction control system indicator/warning light “TCS”Right turn signal indicator light “ ”High beam indicator light “ ”Neutral indicator light “ ”Fuel level warning light “ ”.Left turn signal indicator light “ ”.Immobilizer system indicator light
123456
11
78910
IN
3
ThligtocogoIf inora cir
TI
Thditeinfothlevanocth
Co
lig
Thgiengi
U2SGE0E0.book Page 5 Wednesday, June 12, 2013 1:15 PM
STRUMENT AND CONTROL FUNCTIONS
3-5
e electrical circuit of the warninght can be checked by turning the key “ON”. The warning light shouldme on for a few seconds, and then off.the warning light does not come onitially when the key is turned to “ON”, if the warning light remains on, haveYamaha dealer check the electricalcuit.
P
is model is also equipped with a self-agnosis device for the fuel level de-ction circuit. If a problem is detected the fuel level detection circuit, thellowing cycle will be repeated untile malfunction is corrected: The fuelel warning light will flash eight times,d then go off for 3.0 seconds. If thiscurs, have a Yamaha dealer checke vehicle.
EAU47753
olant temperature warning
ht “ ”
is warning light comes on if the en-ne overheats. If this occurs, stop thegine immediately and allow the en-
ne to cool.
The electrical circuit of the warninglight can be checked by turning the keyto “ON”. The warning light shouldcome on for a few seconds, and thengo off.If the warning light does not come oninitially when the key is turned to “ON”,or if the warning light remains on, havea Yamaha dealer check the electricalcircuit.
NOTICEECA10022
Do not continue to operate the en-
gine if it is overheating.
TIP
For radiator-fan-equipped vehi-cles, the radiator fan(s) automati-cally switch on or off according tothe coolant temperature in the ra-diator.
If the engine overheats, see page6-41 for further instructions.
NTROL FUNCTIONS
3
What to do
OK. Go ahead with riding.
OK. Go ahead with riding.
Stop the vehicle and allow it to idle until the coolant temperature goes down.If the temperature does not go down, stop the engine. (See page 6-41.)
U2SGE0E0.book Page 6 Wednesday, June 12, 2013 1:15 PM
INSTRUMENT AND CO
3-6
Display Conditions
Under 40 °C (Under 104 °F) Message “Lo” is displayed.
40–116 °C (104–242 °F)
Coolant temperature is dis-played.
Above 116 °C (Above 242 °F)
Coolant temperature flash-es.Warning light comes on.
IN
3
En
Thif acircusefodeThligtocogoIf inora cir
Tr
to
ThwgaThchThon
to reset the traction control system the lights by following the proce-es under “Resetting” on page 3-23.
EAU11575
ft timing indicator light
s indicator light can be set to comeand go off at the desired engineeds and is used to inform the rider
en it is time to shift to the next high-ear. electrical circuit of the indicatort can be checked by turning the key“ON”. The indicator light shoulde on for a few seconds, and then
off.e indicator light does not come on
ially when the key is turned to “ON”,f the indicator light remains on, haveamaha dealer check the electricaluit. (See page 3-15 for a detailedlanation of the function of this indi-or light and on how to set it.)
U2SGE0E0.book Page 7 Wednesday, June 12, 2013 1:15 PM
STRUMENT AND CONTROL FUNCTIONS
3-7
EAU11535
gine trouble warning light “ ”
is warning light comes on or flashes problem is detected in the electricalcuit monitoring the engine. If this oc-rs, have a Yamaha dealer check thelf-diagnosis system. (See page 3-15r an explanation of the self-diagnosisvice.)e electrical circuit of the warninght can be checked by turning the key “ON”. The warning light shouldme on for a few seconds, and then off.the warning light does not come onitially when the key is turned to “ON”, if the warning light remains on, haveYamaha dealer check the electricalcuit.
EAU51851
action control system indica-
r/warning light “TCS”
is indicator/warning light flasheshen the traction control system en-ges.e electrical circuit of the light can beecked by turning the key to “ON”.e light should come on for a few sec-ds, and then go off.
If the light does not come on initiallywhen the key is turned to “ON”, or if thelight remains on, have a Yamaha dealercheck the electrical circuit.When the traction control system is setto a “TCS” mode other than “OFF”,and the traction control system is oper-ating, the indicator light flashes.If the traction control system disableswhile riding, “TCS OFF” is displayed,and the indicator/warning light and en-gine trouble warning light come on.(See page 3-22 for an explanation ofthe traction control system.)
Tryanddur
Shi
Thion spewher gThelighto comgo If thinitor ia Ycircexpcat
1. Engine trouble warning light “ ”2. Traction control system indicator/warning
light “TCS”3. Traction control system mode display
1
2
3
NTROL FUNCTIONS
3
Im
TligtocgIfinoacW3ligmhwlizTpcn
ttings while riding can distract the
erator and increase the risk of an
cident.
e multi-function meter unit isuipped with the following:
a speedometera tachometeran odometertwo tripmeters (which show thedistance traveled since they werelast set to zero)a fuel reserve tripmeter (whichshows the distance traveled sincethe fuel level warning light cameon)a stopwatcha clocka coolant temperature displayan air intake temperature displaya transmission gear displaya drive mode display (whichshows the selected drive mode)a fuel consumption display (in-stantaneous and average con-sumption functions)a traction control system modedisplay (which shows the selectedtraction control system mode)
U2SGE0E0.book Page 8 Wednesday, June 12, 2013 1:15 PM
INSTRUMENT AND CO
3-8
EAU38625
mobilizer system indicator light
he electrical circuit of the indicatorht can be checked by turning the key “ON”. The indicator light should
ome on for a few seconds, and theno off. the indicator light does not come onitially when the key is turned to “ON”,r if the indicator light remains on, have Yamaha dealer check the electricalircuit.hen the key is turned to “OFF” and
0 seconds have passed, the indicatorht will start flashing indicating the im-obilizer system is enabled. After 24
ours have passed, the indicator lightill stop flashing, however the immobi-er system is still enabled.
he self-diagnosis device also detectsroblems in the immobilizer systemircuits. (See page 3-15 for an expla-ation of the self-diagnosis device.)
EAU51814
Multi-function meter unit
WARNING
EWA12423
Be sure to stop the vehicle before
making any setting changes to the
multi-function meter unit. Changing
se
op
ac
Theq
1. “RESET” button2. “SELECT” button3. Tachometer4. Shift timing indicator light5. Traction control system mode display6. Coolant temperature display/air intake tem-
perature display7. Drive mode display8. Speedometer9. Odometer/tripmeter/fuel reserve tripme-
ter/instantaneous fuel consumption dis-play/average fuel consumption display
10.Clock/stopwatch11.Transmission gear display
2
1
3 4
56789
1011
IN
3
TI
ck and stopwatch modes
set the clockPush the “SELECT” button and“RESET” button together for atleast two seconds.When the hour digits start flash-ing, push the “RESET” button toset the hours.Push the “SELECT” button, andthe minute digits start flashing.Push the “RESET” button to setthe minutes.Push the “SELECT” button andthen release it to start the clock.
lock/stopwatch
1
U2SGE0E0.book Page 9 Wednesday, June 12, 2013 1:15 PM
STRUMENT AND CONTROL FUNCTIONS
3-9
a self-diagnosis devicea display brightness and shift tim-ing indicator light control mode
P
Be sure to turn the key to “ON” be-fore using the “SELECT” and “RE-SET” buttons, except for settingthe display brightness and shifttiming indicator light controlmode.For the U.K. only: To switch thespeedometer and odometer/trip-meter/fuel consumption displaysbetween kilometers and miles,press the “SELECT” button for atleast one second.
Tachometer
The electric tachometer allows the rid-er to monitor the engine speed andkeep it within the ideal power range.When the key is turned to “ON”, the ta-chometer needle sweeps once acrossthe r/min range and then returns tozero r/min in order to test the electricalcircuit.
NOTICEECA10032
Do not operate the engine in the ta-
chometer red zone.
Red zone: 13750 r/min and above
Clo
To 1.
2.
3.
4.
5.
1. Tachometer2. Tachometer red zone
2
1
1. C
NTROL FUNCTIONS
3
TTwtocm“Rthw
S
S
Push the “SELECT” button againto select the speed mode; “F-20”displays on the stopwatch.
Reverse chronological ordermode: The split times are shownfrom the latest to earliest (i.e., L1,L2, L3, L4).Speed order mode: The split timesare shown from the fastest toslowest (i.e., F1, F2, F3, F4).
. Push the “RESET” button. De-pending on the selected split time,“L1” or “F1” displays on the cool-ant temperature display/air intaketemperature display, and its corre-sponding stored split time dis-plays on the stopwatch.
. Push the “SELECT” button toswitch the displayed split time inascending order (i.e., 1, 2, 3, 4),and the “RESET” button to switchthe displayed split time in de-scending order (i.e., 20, 19, 18,17).
U2SGE0E0.book Page 10 Wednesday, June 12, 2013 1:15 PM
INSTRUMENT AND CO
3-10
o display the stopwatcho change the display to the stop-atch mode, push the “SELECT” but-n and “RESET” button together. To
hange the display back to the clockode, push the “SELECT” button andESET” button together; however,is is not possible when the stop-atch is counting.
tandard measurement1. Push the “RESET” button to start
the stopwatch.2. Push the “SELECT” button to stop
the stopwatch.3. Push the “SELECT” button again
to reset the stopwatch.
plit time measurement1. Push the “RESET” button to start
the stopwatch.2. Push the start switch “ ” or “RE-
SET” button to measure splittimes. Split times are displayed onthe odometer display for five sec-onds.
3. Push the start switch “ ” or “RE-SET” button to display the finalsplit time or push the “SELECT”button to stop the stopwatch anddisplay the final split time.
Split time history
The split time history displays up to 20stored split times. The split time historycan be displayed either in reversechronological order or by speed.
1. Push the “SELECT” button for atleast one second to select the re-verse chronological order mode;“L-20” displays on the stopwatch.
TIP
2
3
1. Coolant temperature display/air intake tem-perature display
2. Stopwatch
2
1
IN
3
TI
4
the UK only:h the “SELECT” button to switch
display between the odometerde “ODO”, the tripmeter modesIP 1” and “TRIP 2”, the instanta-us fuel consumption mode “km/L”,
100 km” or “MPG”, and the averagel consumption mode “AVE_ _._/L”, “AVE_ _._ L/100 km” or “AVE_ MPG” in the following order:
O → TRIP 1 → TRIP 2 → km/L,00 km or MPG → AVE_ _._ km/L,_ _._ L/100 km or AVE_ _._ MPG →
O
e fuel level warning light comes one page 3-4), the display automati-ly changes to the fuel reserve trip-ter mode “TRIP F” and startsnting the distance traveled fromt point. In that case, push the “SE-T” button to switch the display be-
en the various tripmeter, odometer,tantaneous fuel consumption andrage fuel consumption modes in following order:
U2SGE0E0.book Page 11 Wednesday, June 12, 2013 1:15 PM
STRUMENT AND CONTROL FUNCTIONS
3-11
P
To switch between the reversechronological order mode and thespeed mode, push the “SELECT”button for at least one second tocancel the currently selectedmode, and then repeat step 1 toselect the desired mode.To reset all the recorded times forthe selected split time history,push the “RESET” button for atleast one second.
. Push the “SELECT” button for atleast one second to cancel thesplit time history and return to thetime measurement.
Odometer, tripmeter, instantaneous
fuel consumption and average fuel
consumption modes
Push the “SELECT” button to switchthe display between the odometermode “ODO”, the tripmeter modes“TRIP 1” and “TRIP 2”, the instanta-neous fuel consumption mode “km/L”or “L/100 km”, and the average fuelconsumption mode “AVE_ _._ km/L” or“AVE_ _._ L/100 km” in the followingorder:
ODO → TRIP 1 → TRIP 2 → km/L orL/100 km → AVE_ _._ km/L or AVE_ _._L/100 km → ODO
ForPusthemo“TRneo“L/fuekm_._
ODL/1AVEOD
If th(secalmecouthaLECtweinsavethe
1. Odometer/tripmeter/fuel reserve tripme-ter/instantaneous fuel consumption dis-play/average fuel consumption display
1
NTROL FUNCTIONS
3
T_→
FTAAT
TinpoIfmmp5
switch between the instantaneousl consumption displays, push the
ELECT” button for one second whene of the displays is shown.
traveling at speeds under 10 km/h0 mi/h), “_ _._” is displayed.
erage fuel consumption mode
e average fuel consumption displayn be set to either “AVE_ _._ km/L”,VE_ _._ L/100 km” or “AVE_ _._G” (for the UK only).
is display shows the average fuelnsumption since it was last reset.
Average fuel consumption display
1
U2SGE0E0.book Page 12 Wednesday, June 12, 2013 1:15 PM
INSTRUMENT AND CO
3-12
RIP F → km/L or L/100 km → AVE_._ km/L or AVE_ _._ L/100 km → ODO TRIP 1 → TRIP 2 → TRIP F
or the UK only: RIP F → km/L, L/100 km or MPG →VE_ _._ km/L, AVE_ _._ L/100 km orVE_ _._ MPG → ODO → TRIP 1 →RIP 2 → TRIP F
o reset a tripmeter, select it by push-g the “SELECT” button, and thenush the “RESET” button for at leastne second. you do not reset the fuel reserve trip-eter manually, it resets itself auto-atically and the display returns to therior mode after refueling and traveling km (3 mi).
Instantaneous fuel consumption mode
The instantaneous fuel consumptiondisplay can be set to either “km/L”,“L/100 km” or “MPG” (for the UK only). “km/L”: The distance that can be
traveled on 1.0 L of fuel under thecurrent riding conditions is shown.
“L/100 km”: The amount of fuelnecessary to travel 100 km underthe current riding conditions isshown.
“MPG” (for the UK only): The dis-tance that can be traveled on1.0 Imp.gal of fuel under the cur-rent riding conditions is shown.
Tofue“Son
TIP
If (6.
Av
Thca“AMPThco
1. Instantaneous fuel consumption display
1
1.
IN
3
TocoLEonTodiLESE
TI
Afsuthele
s display indicates which drivede has been selected: “STD”, “A” or. For more details on the modes on how to select them, refer toes 3-18 and 3-20.
olant temperature display
coolant temperature display indi-es the temperature of the coolant.
en the coolant temperature displayelected, “C” is displayed for oneond, and then the coolant tempera- is displayed.
oolant temperature display
1
U2SGE0E0.book Page 13 Wednesday, June 12, 2013 1:15 PM
STRUMENT AND CONTROL FUNCTIONS
3-13
“AVE_ _._ km/L”: The average dis-tance that can be traveled on 1.0 Lof fuel is shown.“AVE_ _._ L/100 km”: The averageamount of fuel necessary to travel100 km is shown.“AVE_ _._ MPG” (for the UK only):The average distance that can betraveled on 1.0 Imp.gal of fuel isshown.
switch between the average fuelnsumption displays, push the “SE-CT” button for one second whene of the displays is shown. reset the average fuel consumption
splay, select it by pushing the “SE-CT” button, and then push the “RE-T” button for at least one second.
P
ter resetting an average fuel con-mption display, “_ _._” is shown forat display until the vehicle has trav-d 1 km (0.6 mi).
Transmission gear display
This display shows the selected gear.The neutral position is indicated by “ ”and by the neutral indicator light.
Drive mode display
Thimo“B”andpag
Co
Thecat
TIP
Whis ssecture
1. Neutral indicator light “ ”2. Transmission gear display
1. Drive mode display
2
1
1
1. C
NTROL FUNCTIONS
3
N
D
g
A
Tcin“OstoPtup
action control system mode dis-
y
is display indicates which tractionntrol system mode has been select-. For more details on the modes and how to select them, refer to page2.
1.
Traction control system mode display
1
U2SGE0E0.book Page 14 Wednesday, June 12, 2013 1:15 PM
INSTRUMENT AND CO
3-14
OTICEECA10022
o not continue to operate the en-
ine if it is overheating.
ir intake temperature display
he air intake temperature display indi-ates the temperature of the air drawnto the air filter case. Turn the key toN”, and push the “RESET” button to
witch the coolant temperature display the air intake temperature display.ush the “RESET” button again to re-rn to the coolant temperature dis-lay.
TIP
Even if the air intake temperatureis set to be displayed, the coolanttemperature warning light comeson if the engine overheats.
When the key is turned to “ON”,the coolant temperature is auto-matically displayed, even if the airintake temperature was displayedprior to turning the key to “OFF”.
When the air intake temperaturedisplay is selected, “A” is dis-played for one second, and then“A” and the air intake temperatureare displayed.
Tr
pla
Thcoedon3-2
Air intake temperature display
1
1.
IN
3
Se
ThagcirIf lizsydiIf circoerIf noa
TICEECA11591
the display indicates an error
e, the vehicle should be checked
soon as possible in order to avoid
ine damage.
play brightness and shift timing
icator light control mode
s mode allows you to make chang-to five settings by performing theowing steps.
Turn the key to “OFF”.Push and hold the “SELECT” but-ton.
1.2.3.
hift timing indicator light activation rangehift timing indicator lightrightness adjustable displaysrightness level display
1 2
3
4
U2SGE0E0.book Page 15 Wednesday, June 12, 2013 1:15 PM
STRUMENT AND CONTROL FUNCTIONS
3-15
lf-diagnosis device
is model is equipped with a self-di-nosis device for various electricalcuits.
a problem is detected in the immobi-er system circuits, the immobilizerstem indicator light flashes and thesplay indicates an error code.a problem is detected in any othercuit, the engine trouble warning lightmes on and the display indicates anror code.the display indicates any error codes,te the code number, and then have
Yamaha dealer check the vehicle.
TIP
If the display indicates immobilizer sys-tem circuit error code 52, this could becaused by transponder interference. Ifthis error code appears, try followingthe procedure below.
1. Use the code re-registering key tostart the engine.
TIP
Make sure there are no other immobi-lizer keys close to the main switch, anddo not keep more than one immobilizerkey on the same key ring! Immobilizersystem keys may cause signal interfer-ence, which may prevent the enginefrom starting.
2. If the engine starts, turn it off andtry starting the engine with thestandard keys.
3. If one or both of the standard keysdo not start the engine, take thevehicle, the code re-registeringkey and both standard keys to aYamaha dealer and have the stan-dard keys re-registered.
NO
If
cod
as
eng
Dis
ind
Thies foll
1.2.
Error code displayImmobilizer system indicator lightEngine trouble warning light “ ”
1
3
2
1. S2. S3. B4. B
NTROL FUNCTIONS
3
. Push the “SELECT” button to con-firm the selected brightness level.The control mode changes to theshift timing indicator light activityfunction.
set the shift timing indicator light ac-ity function. Push the “RESET” button to select
one of the following indicator lightactivity settings: The indicator light stays on
when activated. (This settingis selected when the indicatorlight stays on.)
The indicator light flasheswhen activated. (This settingis selected when the indicatorlight flashes four times persecond.)
The indicator light is deacti-vated; in other words, it doesnot come on or flash. (Thissetting is selected when theindicator light flashes onceevery two seconds.)
U2SGE0E0.book Page 16 Wednesday, June 12, 2013 1:15 PM
INSTRUMENT AND CO
3-16
3. Turn the key to “ON”, and then re-lease the “SELECT” button afterfive seconds. The display bright-ness function is selected.
4. Push the “SELECT” button toswitch the functions in the orderbelow.a. Display brightness:
This function allows you to ad-just the brightness of the dis-plays and tachometer to suitthe outside lighting conditions.
b. Shift timing indicator light ac-tivity:This function allows you tochoose whether or not the indi-cator light should be activatedand whether it should flash orstay on when activated.
c. Shift timing indicator light acti-vation:This function allows you to se-lect the engine speed at whichthe indicator light is activated.
d. Shift timing indicator light de-activation:
This function allows you to se-lect the engine speed at whichthe indicator light is deactivat-ed.
e. Shift timing indicator lightbrightness:This function allows you to ad-just the brightness of the indi-cator light to suit yourpreference.
TIP
The display shows the current settingfor each function, except the shift tim-ing indicator light activity function.
To adjust the brightness of the multi-function meter displays and tachome-ter
1. Turn the key to “OFF”.2. Push and hold the “SELECT” but-
ton.3. Turn the key to “ON”, and then re-
lease the “SELECT” button afterfive seconds.
4. Push the “RESET” button to selectthe desired brightness level.
5
Totiv
1
IN
3
2
Totiv
TI
Thtior/mr/mcaFrinof
1
2
adjust the shift timing indicator lighthtnessPush the “RESET” button to selectthe desired indicator light bright-ness level.Push the “SELECT” button to con-firm the selected indicator lightbrightness level. The display re-turns to the odometer or tripmetermode.
U2SGE0E0.book Page 17 Wednesday, June 12, 2013 1:15 PM
STRUMENT AND CONTROL FUNCTIONS
3-17
. Push the “SELECT” button to con-firm the selected indicator light ac-tivity. The control mode changesto the shift timing indicator lightactivation function.
set the shift timing indicator light ac-ation function
P
e shift timing indicator light activa-n function can be set between 7000in and 15000 r/min. From 7000in to 12000 r/min, the indicator light
n be set in increments of 500 r/min.om 12000 r/min to 15000 r/min, thedicator light can be set in increments 200 r/min.
. Push the “RESET” button to selectthe desired engine speed for acti-vating the indicator light.
. Push the “SELECT” button to con-firm the selected engine speed.The control mode changes to theshift timing indicator light deacti-vation function.
To set the shift timing indicator lightdeactivation function
TIP
The shift timing indicator light de-activation function can be set be-tween 7000 r/min and 15000r/min. From 7000 r/min to 12000r/min, the indicator light can be setin increments of 500 r/min. From12000 r/min to 15000 r/min, the in-dicator light can be set in incre-ments of 200 r/min.
Be sure to set the deactivationfunction to a higher engine speedthan for the activation function,otherwise the shift timing indicatorlight remains deactivated.
1. Push the “RESET” button to selectthe desired engine speed for de-activating the indicator light.
2. Push the “SELECT” button to con-firm the selected engine speed.The control mode changes to theshift timing indicator light bright-ness function.
To brig
1.
2.
NTROL FUNCTIONS
3
DDemPto3m
T
Buo
M
Min
EAU1234E
ndlebar switches
ft
1.
Pass switch “ ”Dimmer switch “ / ”Turn signal switch “ / ”Horn switch “ ”Traction control system switch “TCS”
5
34
2
1
U2SGE0E0.book Page 18 Wednesday, June 12, 2013 1:15 PM
INSTRUMENT AND CO
3-18
EAU47633
-mode (drive mode)-mode is an electronically controlledngine performance system with threeode selections (“STD”, “A”, and “B”).ush the drive mode switch “MODE” switch between modes. (See page
-20 for an explanation of the driveode switch.)
IP
efore using D-mode, make sure younderstand its operation along with theperation of the drive mode switch.
ode “STD”
ode “STD” is suitable for various rid-g conditions.
This mode allows the rider to enjoysmooth and sporty drivability from thelow-speed range to the high-speedrange.
Mode “A”
Mode “A” offers a sportier engine re-sponse in the low- to mid-speed rangecompared to mode “STD”.
Mode “B”
Mode “B” offers response that issomewhat less sharp compared tomode “STD” for riding situations thatrequire especially sensitive throttle op-eration.
Ha
Le
Drive mode switch “MODE”
1
1.2.3.4.5.
IN
3
Ri
Ha
Pa
Prlig
EAU12661
ine stop switch “ / ”
this switch to “ ” before starting engine. Set this switch to “ ” top the engine in case of an emergen- such as when the vehicle overturns
hen the throttle cable is stuck.
EAU12712
rt switch “ ”
h this switch to crank the engineh the starter. See page 5-1 for start- instructions prior to starting the en-e.
EAU41701
engine trouble warning light wille on when the key is turned to” and the start switch is pushed,
this does not indicate a malfunc-.
EAU12734
zard switch “ ”
h the key in the “ON” or “ ” posi-, use this switch to turn on the haz- lights (simultaneous flashing of all signal lights).
1.2.3.
1.
U2SGE0E0.book Page 19 Wednesday, June 12, 2013 1:15 PM
STRUMENT AND CONTROL FUNCTIONS
3-19
ght
zard switch
EAU12381
ss switch “ ”
ess this switch to flash the head-hts.
EAU12401
Dimmer switch “ / ”
Set this switch to “ ” for the highbeam and to “ ” for the low beam.
EAU12461
Turn signal switch “ / ”
To signal a right-hand turn, push thisswitch to “ ”. To signal a left-handturn, push this switch to “ ”. Whenreleased, the switch returns to the cen-ter position. To cancel the turn signallights, push the switch in after it has re-turned to the center position.
EAU12501
Horn switch “ ”
Press this switch to sound the horn.
EAU51842
Traction control system switch
“TCS”
This switch is used to select the trac-tion control system modes.See “Traction control system” on page3-22 for detailed information.
Eng
Setthestocy,or w
Sta
Puswitinggin
Thecom“ONbuttion
Ha
Wittionardturn
Engine stop switch “ / ”Drive mode switch “MODE”Start switch “ ”
Hazard switch “ ”
2
1
3
1
NTROL FUNCTIONS
3
Tewm
N
D
e
g
te
D
D
v
UmloSTcmti
EAU12821
utch lever
e clutch lever is located at the leftndlebar grip. To disengage thetch, pull the lever toward the han-bar grip. To engage the clutch, re-se the lever. The lever should belled rapidly and released slowly forooth clutch operation.e clutch lever is equipped with atch switch, which is part of the igni-n circuit cut-off system. (See page6.)
Clutch lever
U2SGE0E0.book Page 20 Wednesday, June 12, 2013 1:15 PM
INSTRUMENT AND CO
3-20
he hazard lights are used in case of anmergency or to warn other drivershen your vehicle is stopped where itight be a traffic hazard.
OTICEECA10062
o not use the hazard lights for an
xtended length of time with the en-
ine not running, otherwise the bat-
ry may discharge.
EAU47495
rive mode switch “MODE”
WARNING
EWA15341
o not change the D-mode while the
ehicle is moving.
sing this switch changes the driveode to “STD”, “A”, or “B” in the fol-wing order:TD → A → B → STDhe throttle grip must be completelylosed in order to change the driveode. (See page 3-18 for an explana-
on of each drive mode.)
TIP
The mode is set to “STD” by de-fault. The “STD” mode resetswhen the key is turned to “OFF”.
The selected mode is shown onthe drive mode display. (See page3-13.)
Cl
ThhacludleleapusmThclutio3-3
1.
IN
3
S
Thsidcoshstth
sure to set it by aligning a groove on adjusting knob with the “ ” markthe brake lever.
1.
U2SGE0E0.book Page 21 Wednesday, June 12, 2013 1:15 PM
STRUMENT AND CONTROL FUNCTIONS
3-21
EAU12872
hift pedal
e shift pedal is located on the lefte of the motorcycle and is used inmbination with the clutch lever whenifting the gears of the 6-speed con-ant-mesh transmission equipped onis motorcycle.
EAU33854
Brake lever
The brake lever is located on the rightside of the handlebar. To apply thefront brake, pull the lever toward thethrottle grip.The brake lever is equipped with abrake lever position adjusting knob. Toadjust the distance between the brakelever and the throttle grip, turn the ad-justing knob while holding the leverpushed away from the throttle grip.When the desired position is obtained,
be theon
Shift pedal
1
1. Brake lever2. Brake lever position adjusting knob3. Distance between brake lever and throttle
grip4. “ ” mark
4
2 1
3
NTROL FUNCTIONS
3
B
Tthb
The traction control may engagewhen the vehicle travels over abump.The rider may notice slight chang-es in engine and exhaust soundswhen the traction control systemis engaged.
ere are six traction control systemdes and an off mode.
“TCS” mode 1 provides for theleast traction control system as-sist.
1.
OFF
Display
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Mode 6
TCS OFF
TCS
TCS
TCS
TCS
TCS
TCS
U2SGE0E0.book Page 22 Wednesday, June 12, 2013 1:15 PM
INSTRUMENT AND CO
3-22
EAU12942
rake pedal
he brake pedal is on the right side ofe motorcycle. To apply the rearrake, press down on the brake pedal.
EAU51862
Traction control systemThe traction control system helpsmaintain traction when accelerating. Ifsensors detect that the rear wheel isstarting to slip (uncontrolled spinning),the traction control system assists byregulating engine power as needed un-til traction is restored. The traction con-trol system indicator/warning lightflashes to let the rider know that trac-tion control has engaged.
WARNING
EWA15432
The traction control system is not a
substitute for riding appropriately
for the conditions. Traction control
cannot prevent loss of traction due
to excessive speed when entering
turns, when accelerating hard at a
sharp lean angle, or while braking,
and cannot prevent front wheel slip-
ping. As with any motorcycle, ap-
proach surfaces that may be
slippery with caution and avoid es-
pecially slippery surfaces.
TIP
Thmo
Brake pedal
1
IN
3
WtrathmAlbepobeincosyw
N
Us
pa
tir
sy
ac
setting
traction control system may beabled in the following conditions:
Either the front wheel or rear wheelcomes off the ground while ridingExcessive rear wheel spinning
raction control system mode display
raction control system switch “TCS”
1
1
U2SGE0E0.book Page 23 Wednesday, June 12, 2013 1:15 PM
STRUMENT AND CONTROL FUNCTIONS
3-23
“TCS” modes 2 through 6 providefor more traction control systemassist. Mode 6 provides the mosttraction control system assist.“TCS OFF” mode turns the trac-tion control system off. The sys-tem may also be automaticallydisabled in some riding conditions(see “Resetting” on page 3-23).
hen the key is turned to “ON”, thection control system is enabled and
e last mode selected displays in theulti-function meter.l traction control system modes can selected when the key is in the “ON”sition. Modes 1 through 6 can also selected when the vehicle is mov-
g, however the throttle grip must bempletely closed. The traction controlstem cannot be turned on or offhile the vehicle is moving.
OTICEECA16801
e only the specified tires. (See
ge 6-18.) Using different sized
es will prevent the traction control
stem from controlling tire rotation
curately.
Setting the traction control system
WARNING
EWA16071
Changing settings while riding can
distract the operator. Therefore,
take extra precaution when chang-
ing modes while riding.
When the vehicle is stopped, push theupper side of the traction control sys-tem switch for at least two seconds toturn the traction control system off.Push the lower side of the switch toturn the traction control system on.When the vehicle is stopped or whileriding, close the throttle and push thelower side of the switch to change frommodes 1 to 6. Close the throttle andpush the upper side of the switch tochange from modes 6 to 1.
TIP
The vehicle was set to “TCS” mode 6at the time of manufacture. Re
Thedis
1. T
1. T
NTROL FUNCTIONS
3
Ifdteg
TTs“OcthtrthkseosYa
N
EAU13075
el tank cap
open the fuel tank cap
en the fuel tank cap lock cover, in-rt the key into the lock, and then turn/4 turn clockwise. The lock will be
eased and the fuel tank cap can beened.
close the fuel tank cap
. Push the fuel tank cap into posi-tion with the key inserted in thelock.
. Turn the key counterclockwise tothe original position, remove it,and then close the lock cover.
Fuel tank cap lock coverUnlock.
U2SGE0E0.book Page 24 Wednesday, June 12, 2013 1:15 PM
INSTRUMENT AND CO
3-24
the traction control system has beenisabled, both the traction control sys-m indicator/warning light and the en-ine trouble warning light come on.
o reset the traction control system:urn the key to “OFF”. Wait at least oneecond, then turn the key back to
N”. The traction control system indi-ator/warning light should go off ande system will be enabled. The engineouble warning light should go off aftere motorcycle reaches at least 20
m/h (12 mi/h). If the traction controlystem indicator/warning light and/orngine trouble warning light still remainn after resetting, the motorcycle maytill be ridden; however, have aamaha dealer check the motorcycles soon as possible.
OTICEECA17732
Keep any type of magnets (in-
cluding magnetic pick-up tools,
magnetic screwdrivers, etc.)
away from the front wheel sen-
sor or rotor; otherwise, the sen-
sor or rotor may be damaged,
resulting in improper perfor-
mance of the traction control
system.
Be careful not to damage the
sensor or rotor.
Fu
To
Opseit 1relop
To
1
2
1. Front wheel sensor rotor2. Front wheel sensor
2
1
1.2.
IN
3
TI
Thlethno
M
pr
Le
Wipe up any spilled fuel immedi-ately. NOTICE: Immediately
wipe off spilled fuel with a clean,
dry, soft cloth, since fuel may
deteriorate painted surfaces or
plastic parts. [ECA10072]
Be sure to securely close the fueltank cap.
WARNING
EWA15152
soline is poisonous and can
se injury or death. Handle gaso-
with care. Never siphon gasoline
mouth. If you should swallow
e gasoline or inhale a lot of gas-
e vapor, or get some gasoline in
r eyes, see your doctor immedi-
uel tank filler tubeaximum fuel level
2 1
U2SGE0E0.book Page 25 Wednesday, June 12, 2013 1:15 PM
STRUMENT AND CONTROL FUNCTIONS
3-25
P
e fuel tank cap cannot be closed un-ss the key is in the lock. In addition,e key cannot be removed if the cap ist properly closed and locked.
WARNING
EWA11092
ake sure that the fuel tank cap is
operly closed after filling fuel.
aking fuel is a fire hazard.
EAU13222
FuelMake sure there is sufficient gasoline inthe tank.
WARNING
EWA10882
Gasoline and gasoline vapors are
extremely flammable. To avoid fires
and explosions and to reduce the
risk of injury when refueling, follow
these instructions.
1. Before refueling, turn off the en-gine and be sure that no one is sit-ting on the vehicle. Never refuelwhile smoking, or while in the vi-cinity of sparks, open flames, orother sources of ignition such asthe pilot lights of water heatersand clothes dryers.
2. Do not overfill the fuel tank. Whenrefueling, be sure to insert thepump nozzle into the fuel tank fillerhole. Stop filling when the fuelreaches the bottom of the fillertube. Because fuel expands whenit heats up, heat from the engine orthe sun can cause fuel to spill outof the fuel tank.
3.
4.
Ga
cau
line
by
som
olin
you
1. F2. M
NTROL FUNCTIONS
3
a
w
li
y
N
U
o
d
s
a
Yso9o
EAU58080
el tank breather hose and erflow hose
fore operating the motorcycle:Check each hose connection.Check each hose for cracks ordamage, and replace if necessary.Make sure that the end of eachhose is not blocked, and clean ifnecessary.Make sure that the end of eachhose is positioned outside of thecowling.Make sure that each hose is rout-ed through the clamp.
ClampFuel tank breather hoseFuel tank overflow hose
2
1
3
U2SGE0E0.book Page 26 Wednesday, June 12, 2013 1:15 PM
INSTRUMENT AND CO
3-26
tely. If gasoline spills on your skin,
ash with soap and water. If gaso-
ne spills on your clothing, change
our clothes.
EAU54601
OTICEECA11401
se only unleaded gasoline. The use
f leaded gasoline will cause severe
amage to internal engine parts,
uch as the valves and piston rings,
s well as to the exhaust system.
our Yamaha engine has been de-igned to use premium unleaded gas-line with a research octane number of5 or higher. If knocking (or pinging)ccurs, use a gasoline of a different
brand. Use of unleaded fuel will extendspark plug life and reduce mainte-nance costs.Gasohol
There are two types of gasohol: gaso-hol containing ethanol and that con-taining methanol. Gasohol containingethanol can be used if the ethanol con-tent does not exceed 10% (E10). Gas-ohol containing methanol is notrecommended by Yamaha because itcan cause damage to the fuel systemor vehicle performance problems.
Fuov
Be
Recommended fuel:Premium unleaded gasoline (Gaso-hol (E10) acceptable)
Fuel tank capacity:18.0 L (4.76 US gal, 3.96 Imp.gal)
Fuel reserve amount (when the fuel level warning light comes on):
3.1 L (0.82 US gal, 0.68 Imp.gal)
1.2.3.
IN
3
CThco
Th
er
bu
EAU47272
ats
senger seat
remove the passenger seatInsert the key into the seat lock,and then turn it clockwise.
Lift the front of the passenger seatand pull it forward.
install the passenger seatInsert the projection on the rear ofthe passenger seat into the seatholder as shown, and then pushthe front of the seat down to lockit in place.
eat locknlock.
1 2
U2SGE0E0.book Page 27 Wednesday, June 12, 2013 1:15 PM
STRUMENT AND CONTROL FUNCTIONS
3-27
EAU13434
atalytic converteris model is equipped with a catalyticnverter in the exhaust system.
WARNING
EWA10863
e exhaust system is hot after op-
ation. To prevent a fire hazard or
rns:
Do not park the vehicle near
possible fire hazards such as
grass or other materials that
easily burn.
Park the vehicle in a place
where pedestrians or children
are not likely to touch the hot
exhaust system.
Make sure that the exhaust sys-
tem has cooled down before
doing any maintenance work.
Do not allow the engine to idle
more than a few minutes. Long
idling can cause a build-up of
heat.
NOTICEECA10702
Use only unleaded gasoline. The use
of leaded gasoline will cause unre-
pairable damage to the catalytic
converter.
Se
Pas
To 1.
2.
To 1.
1. S2. U
NTROL FUNCTIONS
3
R
T
. Install the bolts with the hexagonwrench.
. Insert the hexagon wrench backinto its holder on the passengerseat.
. Install the passenger seat.
ke sure that the seats are properlycured before riding.
1.2.
ProjectionSeat holder
1
2
1
U2SGE0E0.book Page 28 Wednesday, June 12, 2013 1:15 PM
INSTRUMENT AND CO
3-28
2. Remove the key.
ider seat
o remove the rider seat1. Remove the passenger seat.2. Pull up the corners on the rear of
the rider seat as shown, removethe bolts with the hexagon wrenchlocated on the bottom of the pas-senger seat, and then pull the seatoff. To install the rider seat
1. Insert the projections into the seatholders as shown, then place theseat in the original position.
2
3
4
TIP
Mase
ProjectionSeat holder
1
2
1. Bolt
1. Passenger seat2. Hexagon wrench
1
2
1
1.2.
IN
3
H
Thbo
To
ho
1
2
EAU14464
rage compartment
storage compartment is locateder the passenger seat. (See page7.)en storing the Owner’s Manual orer documents in the storage com-tment, be sure to wrap them in astic bag so that they will not get wet.en washing the vehicle, be careful to let any water enter the storagepartment.
WARNING
EWA10962
Do not exceed the load limit of 1
kg (2 lb) for the storage com-
partment.
1. torage compartment
1
U2SGE0E0.book Page 29 Wednesday, June 12, 2013 1:15 PM
STRUMENT AND CONTROL FUNCTIONS
3-29
EAU47531
elmet holder
e helmet holder is located on thettom of the passenger seat.
secure a helmet to the helmet
lder
. Remove the passenger seat. (Seepage 3-27.)
. Attach the helmet to the helmetholder, and then securely installthe passenger seat. WARNING!
Never ride with a helmet at-
tached to the helmet holder,
since the helmet may hit ob-
jects, causing loss of control
and possibly an accident. [EWA10162]
To release the helmet from the hel-
met holder
Remove the passenger seat, removethe helmet from the helmet holder, andthen install the seat.
Sto
Theund3-2WhothparplaWhnotcom
Helmet holder
1
1. S
NTROL FUNCTIONS
3
EAU47261
ar view mirrorse rear view mirrors of this vehiclen be folded forward for parking inrrow spaces. Fold the mirrors backtheir original position before riding.
WARNING
EWA14372
sure to fold the rear view mirrors
ck to their original position before
ing.
Riding positionParking position
1
22
U2SGE0E0.book Page 30 Wednesday, June 12, 2013 1:15 PM
INSTRUMENT AND CO
3-30
Do not exceed the maximum
load of 189 kg (417 lb) for the ve-
hicle.
EAU47443
Rider footrest positionThe rider footrests can be adjusted toone of two positions to suit the rider’spreference. Have a Yamaha dealer ad-just the position of the rider footrests.
Left side
Right side
ReThcanato
Be
ba
rid
1. Rider footrest
1. Rider footrest
1
1
1.2.
1
IN
3
A
Al
bo
po
m
Easpfroboanprsc
N
To
do
m
Sp
Toththre
bound damping force
rebound damping force is adjust-on the right front fork leg only. To in-ase the rebound damping force andreby harden the rebound damping, the adjusting screw in direction (a).decrease the rebound dampinge and thereby soften the reboundping, turn the adjusting screw in
ction (b).
sure to perform this adjustment on right front fork leg.
pring preload setting:Minimum (soft):
0Standard:
2Maximum (hard):
5
U2SGE0E0.book Page 31 Wednesday, June 12, 2013 1:15 PM
STRUMENT AND CONTROL FUNCTIONS
3-31
EAU47622
djusting the front fork
WARNING
EWA14671
ways adjust the spring preload on
th fork legs equally, otherwise
or handling and loss of stability
ay result.
ch front fork leg is equipped with aring preload adjusting bolt, the rightnt fork leg is equipped with a re-und damping force adjusting screwd the left front fork leg with a com-ession damping force adjustingrew.
OTICEECA10102
avoid damaging the mechanism,
not attempt to turn beyond the
aximum or minimum settings.
ring preload
increase the spring preload andereby harden the suspension, turne adjusting bolt on each fork leg in di-ction (a). To decrease the spring pre-
load and thereby soften thesuspension, turn the adjusting bolt oneach fork leg in direction (b).
Align the appropriate groove on the ad-justing mechanism with the top of thefront fork collar.
Re
Theed cretheturnTo forcdamdire
TIP
Be the
1. Spring preload adjusting bolt
1. Current setting2. Front fork collar
1
01
23
45
12
S
NTROL FUNCTIONS
3
C
Tjuinfops
hough the total number of clicks of amping force adjusting mechanismy not exactly match the above
ecifications due to small differencesproduction, the actual number ofks always represents the entire ad-ting range. To obtain a precise ad-tment, it would be advisable toeck the number of clicks of eachmping force adjusting mechanismd to modify the specifications ascessary.
1.
U2SGE0E0.book Page 32 Wednesday, June 12, 2013 1:15 PM
INSTRUMENT AND CO
3-32
ompression damping force
he compression damping force is ad-sted on the left front fork leg only. Tocrease the compression dampingrce and thereby harden the com-ression damping, turn the adjustingcrew in direction (a). To decrease the
compression damping force and there-by soften the compression damping,turn the adjusting screw in direction (b).
TIP
Be sure to perform this adjustment onthe left front fork leg.
TIP
Altdamaspin clicjusjuschdaanne
Rebound damping force adjusting screw
Rebound damping setting:Minimum (soft):
25 click(s) in direction (b)*Standard:
12 click(s) in direction (b)*Maximum (hard):
1 click(s) in direction (b)** With the adjusting screw fully
turned in direction (a)
(b)1
(a)
1. Compression damping force adjusting screw
Compression damping setting:Minimum (soft):
25 click(s) in direction (b)*Standard:
20 click(s) in direction (b)*Maximum (hard):
1 click(s) in direction (b)** With the adjusting screw fully
turned in direction (a)
1
IN
3
AasTheqinadinprdaco
N
To
do
m
Sp
Toththdebyju
ebound damping force adjusting screw
ebound damping setting:Minimum (soft):
20 click(s) in direction (b)*Standard:
15 click(s) in direction (b)*Maximum (hard):
3 click(s) in direction (b)** With the adjusting screw fully
turned in direction (a)
1(a)
(b)
U2SGE0E0.book Page 33 Wednesday, June 12, 2013 1:15 PM
STRUMENT AND CONTROL FUNCTIONS
3-33
EAU51891
djusting the shock absorber semblyis shock absorber assembly isuipped with a spring preload adjust-
g screw, a rebound damping forcejusting screw, a compression damp-
g force adjusting bolt (for fast com-ession damping) and a compressionmping force adjusting bolt (for slowmpression damping).
OTICEECA10102
avoid damaging the mechanism,
not attempt to turn beyond the
aximum or minimum settings.
ring preload
increase the spring preload andereby harden the suspension, turne adjusting screw in direction (a). Tocrease the spring preload and there- soften the suspension, turn the ad-
sting screw in direction (b).
Rebound damping force
To increase the rebound dampingforce and thereby harden the rebounddamping, turn the adjusting screw indirection (a). To decrease the rebounddamping force and thereby soften therebound damping, turn the adjustingscrew in direction (b).
1. Spring preload adjusting screw
Spring preload setting:Minimum (soft):
16 turn(s) in direction (b)*Standard:
8 turn(s) in direction (b)*Maximum (hard):
0 turn(s) in direction (b)** With the adjusting screw fully
turned in direction (a)
1
(a)(b)
1. R
R
NTROL FUNCTIONS
3
C
CcTfopbcbtu
obtain a precise adjustment, it isvisable to check the actual totalmber of clicks or turns of eachmping force adjusting mechanism.is adjustment range may not exactlytch the specifications listed due toall differences in production.
WARNING
EWA10222
is shock absorber assembly con-
ns highly pressurized nitrogen
s. Read and understand the fol-
ing information before handling
shock absorber assembly.
Do not tamper with or attempt
to open the cylinder assembly.
Do not subject the shock ab-
sorber assembly to an open
flame or other high heat source.
This may cause the unit to ex-
plode due to excessive gas
pressure.
Do not deform or damage the
cylinder in any way. Cylinder
damage will result in poor
damping performance.
1.
2.
U2SGE0E0.book Page 34 Wednesday, June 12, 2013 1:15 PM
INSTRUMENT AND CO
3-34
ompression damping force
ompression damping force (for fastompression damping)o increase the compression dampingrce and thereby harden the com-ression damping, turn the adjustingolt in direction (a). To decrease theompression damping force and there-y soften the compression damping,rn the adjusting bolt in direction (b).
Compression damping force (for slowcompression damping)To increase the compression dampingforce and thereby harden the com-pression damping, turn the adjustingbolt in direction (a). To decrease thecompression damping force and there-by soften the compression damping,turn the adjusting bolt in direction (b).
TIP
ToadnudaThmasm
Th
tai
ga
low
the
Compression damping force adjusting bolt (for fast compression damping)Compression damping force adjusting bolt (for slow compression damping)
1
2
(a)
(b)
Compression damping setting (for fast compression damping):
Minimum (soft):4 turn(s) in direction (b)*
Standard:3 turn(s) in direction (b)*
Maximum (hard):0 turn(s) in direction (b)*
* With the adjusting bolt fully turned in direction (a)
Compression damping setting (for slow compression damping):
Minimum (soft):20 click(s) in direction (b)*
Standard:9 click(s) in direction (b)*
Maximum (hard):1 click(s) in direction (b)*
* With the adjusting bolt fully turned in direction (a)
IN
3
EAU15306
estand sidestand is located on the left
e of the frame. Raise the sidestandower it with your foot while holding vehicle upright.
built-in sidestand switch is part of ignition circuit cut-off system,ich cuts the ignition in certain situa-s. (See the following section for anlanation of the ignition circuit cut-system.)
WARNING
EWA10242
vehicle must not be ridden with
sidestand down, or if the side-
nd cannot be properly moved up
does not stay up), otherwise the
estand could contact the ground
distract the operator, resulting
a possible loss of control.
aha’s ignition circuit cut-off
tem has been designed to assist
operator in fulfilling the respon-
ility of raising the sidestand be-
e starting off. Therefore, check
U2SGE0E0.book Page 35 Wednesday, June 12, 2013 1:15 PM
STRUMENT AND CONTROL FUNCTIONS
3-35
Do not dispose of a damaged or
worn-out shock absorber as-
sembly yourself. Take the shock
absorber assembly to a Yamaha
dealer for any service.
EAU15183
Luggage strap holders
There are four luggage strap holderson the bottom of the passenger seat.To use the strap holders, remove thepassenger seat. (See page 3-27.) Un-hook the straps from the hooks, andthen install the seat with the strapshanging out from under the passengerseat.
SidThesidor lthe
TIP
Thethewhtionexpoff
The
the
sta
(or
sid
and
in
Yam
sys
the
sib
for
1. Luggage strap holder2. Hook
2
1
2
1
NTROL FUNCTIONS
3
th
Y
fu
U2SGE0E0.book Page 36 Wednesday, June 12, 2013 1:15 PM
INSTRUMENT AND CO
3-36
is system regularly and have a
amaha dealer repair it if it does not
nction properly.
EAU44893
Ignition circuit cut-off systemThe ignition circuit cut-off system(comprising the sidestand switch,clutch switch and neutral switch) hasthe following functions. It prevents starting when the
transmission is in gear and thesidestand is up, but the clutch le-ver is not pulled.
It prevents starting when thetransmission is in gear and theclutch lever is pulled, but the side-stand is still down.
It cuts the running engine whenthe transmission is in gear and thesidestand is moved down.
Periodically check the operation of theignition circuit cut-off system accord-ing to the following procedure.
IN
3 h may not be working correctly. should not be ridden until
aha dealer.
itch may not be working correctly. should not be ridden until
aha dealer.
may not be working correctly. should not be ridden until
aha dealer.
is noted, have a Yamaha system before riding.
U2SGE0E0.book Page 37 Wednesday, June 12, 2013 1:15 PM
STRUMENT AND CONTROL FUNCTIONS
3-37
With the engine turned off:1. Move the sidestand down.2. Make sure that the engine stop switch is set to “3. Turn the key on. 4. Shift the transmission into the neutral position.5. Push the start switch.Does the engine start?
With the engine still running:6. Move the sidestand up.7. Keep the clutch lever pulled.8. Shift the transmission into gear.9. Move the sidestand down.Does the engine stall?
After the engine has stalled:10. Move the sidestand up.11. Keep the clutch lever pulled.12. Push the start switch.Does the engine start?
The system is OK. The motorcycle can be ridden.
The neutral switcThe motorcyclechecked by a Yam
The sidestand swThe motorcyclechecked by a Yam
The clutch switchThe motorcyclechecked by a Yam
YES NO
YES NO
YES NO
If a malfunctiondealer check the
WARNING
”.
PERATION CHECKS
4
EAU15598
In ndition. Always follow the inspectiona
EWA11152
F accident or equipment damage.
D ted by the procedures provided in
th
B
PAGE
Fracks or
3-25, 3-26
E 6-11
C 6-14
F 6-23, 6-24
U2SGE0E0.book Page 1 Wednesday, June 12, 2013 1:15 PM
FOR YOUR SAFETY – PRE-O
4-1
spect your vehicle each time you use it to make sure the vehicle is in safe operating cond maintenance procedures and schedules described in the Owner’s Manual.
WARNING
ailure to inspect or maintain the vehicle properly increases the possibility of an
o not operate the vehicle if you find any problem. If a problem cannot be correc
is manual, have the vehicle inspected by a Yamaha dealer.
efore using this vehicle, check the following points:
ITEM CHECKS
uel
• Check fuel level in fuel tank.• Refuel if necessary.• Check fuel line for leakage.• Check fuel tank breather hose and overflow hose for obstructions, c
damage, and check hose connections.
ngine oil• Check oil level in engine.• If necessary, add recommended oil to specified level.• Check vehicle for oil leakage.
oolant• Check coolant level in reservoir.• If necessary, add recommended coolant to specified level.• Check cooling system for leakage.
ront brake
• Check operation.• If soft or spongy, have Yamaha dealer bleed hydraulic system.• Check brake pads for wear.• Replace if necessary.• Check fluid level in reservoir.• If necessary, add specified brake fluid to specified level.• Check hydraulic system for leakage.
F
4
R 6-23, 6-24
C 6-21
T ricate ca- 6-18, 6-28
C 6-27
D 6-25, 6-27
W 6-18, 6-21
B 6-28
B 6-29
S 6-29
PAGE
U2SGE0E0.book Page 2 Wednesday, June 12, 2013 1:15 PM
OR YOUR SAFETY – PRE-OPERATION CHECKS
4-2
ear brake
• Check operation.• If soft or spongy, have Yamaha dealer bleed hydraulic system.• Check brake pads for wear.• Replace if necessary.• Check fluid level in reservoir.• If necessary, add specified brake fluid to specified level.• Check hydraulic system for leakage.
lutch
• Check operation.• Lubricate cable if necessary.• Check lever free play.• Adjust if necessary.
hrottle grip
• Make sure that operation is smooth.• Check throttle grip free play.• If necessary, have Yamaha dealer adjust throttle grip free play and lub
ble and grip housing.
ontrol cables• Make sure that operation is smooth.• Lubricate if necessary.
rive chain
• Check chain slack.• Adjust if necessary.• Check chain condition.• Lubricate if necessary.
heels and tires
• Check for damage.• Check tire condition and tread depth.• Check air pressure.• Correct if necessary.
rake and shift pedals• Make sure that operation is smooth.• Lubricate pedal pivoting points if necessary.
rake and clutch levers• Make sure that operation is smooth.• Lubricate lever pivoting points if necessary.
idestand• Make sure that operation is smooth.• Lubricate pivot if necessary.
ITEM CHECKS
PERATION CHECKS
4
C —
Ia
—
S . 3-35
PAGE
U2SGE0E0.book Page 3 Wednesday, June 12, 2013 1:15 PM
FOR YOUR SAFETY – PRE-O
4-3
hassis fasteners• Make sure that all nuts, bolts and screws are properly tightened.• Tighten if necessary.
nstruments, lights, signals nd switches
• Check operation.• Correct if necessary.
idestand switch • Check operation of ignition circuit cut-off system.• If system is not working correctly, have Yamaha dealer check vehicle
ITEM CHECKS
O
5
Rebethun
Fa
th
tro
or
EAU51881
rting the enginerder for the ignition circuit cut-off
tem to enable starting, one of theowing conditions must be met:
The transmission is in the neutralposition.The transmission is in gear withthe clutch lever pulled and thesidestand up.See page 3-36 for more informa-tion.Turn the key to “ON” and makesure that the engine stop switch isset to “ ”.The following warning lights andindicator lights should come on fora few seconds, then go off. Oil level warning light Fuel level warning light Coolant temperature warning
light Shift timing indicator light Engine trouble warning light Traction control system indi-
cator/warning light Immobilizer system indicator
light
U2SGE0E0.book Page 1 Wednesday, June 12, 2013 1:15 PM
PERATION AND IMPORTANT RIDING POINTS
5-1
EAU15952
ad the Owner’s Manual carefully tocome familiar with all controls. Ifere is a control or function you do notderstand, ask your Yamaha dealer.
WARNING
EWA10272
ilure to familiarize yourself with
e controls can lead to loss of con-
l, which could cause an accident
injury.
EAU48711
TIP
This model is equipped with: a lean angle sensor to stop the en-
gine in case of a turnover. In thiscase, the multi-function display in-dicates error code 30, but this isnot a malfunction. Turn the key to“OFF” and then to “ON” to clearthe error code. Failing to do so willprevent the engine from startingeven though the engine will crankwhen pushing the start switch.
an engine auto-stop system. Theengine stops automatically if leftidling for 20 minutes. If the enginestops, simply push the startswitch to restart the engine.
StaIn osysfoll
1.
ANT RIDING POINTS
5
N
If
n
tu
d
3
a
N
F
c
c
OTICEECA10261
Even with the transmission in
the neutral position, do not
coast for long periods of time
with the engine off, and do not
tow the motorcycle for long dis-
tances. The transmission is
properly lubricated only when
the engine is running. Inade-
quate lubrication may damage
the transmission.
Always use the clutch while
changing gears to avoid dam-
aging the engine, transmission,
and drive train, which are not
designed to withstand the
shock of forced shifting.
U2SGE0E0.book Page 2 Wednesday, June 12, 2013 1:15 PM
OPERATION AND IMPORT
5-2
OTICEECA11834
a warning or indicator light does
ot come on initially when the key is
rned to “ON”, or if a warning or in-
icator light remains on, see page
-4 for the corresponding warning
nd indicator light circuit check.
2. Shift the transmission into theneutral position. The neutral indi-cator light should come on. If not,ask a Yamaha dealer to check theelectrical circuit.
3. Start the engine by pushing thestart switch.If the engine fails to start, releasethe start switch, wait a few sec-onds, and then try again. Eachstarting attempt should be asshort as possible to preserve thebattery. Do not crank the enginemore than 10 seconds on any oneattempt.
OTICEECA11043
or maximum engine life, never ac-
elerate hard when the engine is
old!
EAU16672
Shifting
Shifting gears lets you control theamount of engine power available forstarting off, accelerating, climbing hills,etc.The gear positions are shown in the il-lustration.
TIP
To shift the transmission into the neu-tral position, press the shift pedal downrepeatedly until it reaches the end of itstravel, and then slightly raise it.
N
1. Shift pedal2. Neutral position
1
1 2
2
3456
N
O
5
TisuFuyoin
0 km (1000 mi) and beyond
vehicle can now be operated nor-lly.
TICEECA10311
Keep the engine speed out of
the tachometer red zone.
If any engine trouble should oc-
cur during the engine break-in
period, immediately have a
Yamaha dealer check the vehi-
cle.
ing and after the engine break-iniod, the exhaust heat may causecoloration of the exhaust pipe, but is normal.
U2SGE0E0.book Page 3 Wednesday, June 12, 2013 1:15 PM
PERATION AND IMPORTANT RIDING POINTS
5-3
EAU16811
ps for reducing fuel con-mptionel consumption depends largely onur riding style. Consider the follow-
g tips to reduce fuel consumption:Shift up swiftly, and avoid high en-gine speeds during acceleration.Do not rev the engine while shift-ing down, and avoid high enginespeeds with no load on the en-gine.Turn the engine off instead of let-ting it idle for an extended lengthof time (e.g., in traffic jams, at traf-fic lights or at railroad crossings).
EAU16842
Engine break-inThere is never a more important periodin the life of your engine than the periodbetween 0 and 1600 km (1000 mi). Forthis reason, you should read the fol-lowing material carefully.Since the engine is brand new, do notput an excessive load on it for the first1600 km (1000 mi). The various parts inthe engine wear and polish themselvesto the correct operating clearances.During this period, prolonged full-throt-tle operation or any condition thatmight result in engine overheatingmust be avoided.
EAU17084
0–1000 km (0–600 mi)
Avoid prolonged operation above 6900r/min. NOTICE: After 1000 km (600
mi) of operation, the engine oil must
be changed and the oil filter car-
tridge or element replaced. [ECA10303]
1000–1600 km (600–1000 mi)
Avoid prolonged operation above 8300r/min.
160
Thema
NO
TIP
Durperdisthis
ANT RIDING POINTS
5
PWths
U2SGE0E0.book Page 4 Wednesday, June 12, 2013 1:15 PM
OPERATION AND IMPORT
5-4
EAU17214
arkinghen parking, stop the engine, anden remove the key from the main
witch.
WARNING
EWA10312
Since the engine and exhaust
system can become very hot,
park in a place where pedestri-
ans or children are not likely to
touch them and be burned.
Do not park on a slope or on soft
ground, otherwise the vehicle
may overturn, increasing the
risk of a fuel leak and fire.
Do not park near grass or other
flammable materials which
might catch fire.
P
6
PelusapovepoadplThmconopegrthbe
Fa
cl
tiv
yo
se
yo
vi
se
EAU17303
ission controls not only function toure cleaner air, but are also vital toper engine operation and maximumformance. In the following periodicintenance charts, the services relat-to emissions control are groupedarately. These services requirecialized data, knowledge, andipment. Maintenance, replace-
nt, or repair of the emission controlices and systems may be per-ed by any repair establishment or
ividual that is certified (if applicable).aha dealers are trained and
ipped to perform these particularvices.
U2SGE0E0.book Page 1 Wednesday, June 12, 2013 1:15 PM
ERIODIC MAINTENANCE AND ADJUSTMENT
6-1
EAU17245
riodic inspection, adjustment, andbrication will keep your vehicle in thefest and most efficient conditionssible. Safety is an obligation of thehicle owner/operator. The most im-rtant points of vehicle inspection,justment, and lubrication are ex-
ained on the following pages.e intervals given in the periodicaintenance charts should be simplynsidered as a general guide underrmal riding conditions. However, de-nding on the weather, terrain, geo-aphical location, and individual use,e maintenance intervals may need to shortened.
WARNING
EWA10322
ilure to properly maintain the vehi-
e or performing maintenance ac-
ities incorrectly may increase
ur risk of injury or death during
rvice or while using the vehicle. If
u are not familiar with vehicle ser-
ce, have a Yamaha dealer perform
rvice.
WARNING
EWA15123
Turn off the engine when performing
maintenance unless otherwise
specified.
A running engine has moving
parts that can catch on body
parts or clothing and electrical
parts that can cause shocks or
fires.
Running the engine while ser-
vicing can lead to eye injury,
burns, fire, or carbon monoxide
poisoning – possibly leading to
death. See page 1-3 for more in-
formation about carbon monox-
ide.
WARNING
EWA15461
Brake discs, calipers, drums, and
linings can become very hot during
use. To avoid possible burns, let
brake components cool before
touching them.
Emenspropermaed sepspeequmedevformindYamequser
AND ADJUSTMENT
6
O
TthTmoymewc
T
Ifea
1.
U2SGE0E0.book Page 2 Wednesday, June 12, 2013 1:15 PM
PERIODIC MAINTENANCE
6-2
EAU17362
wner’s tool kit
he owner’s tool kit is located undere rider seat. (See page 3-27.)
he service information included in thisanual and the tools provided in the
wner’s tool kit are intended to assistou in the performance of preventiveaintenance and minor repairs. How-
ver, additional tools such as a torquerench may be necessary to performertain maintenance work correctly.
IP
you do not have the tools or experi-nce required for a particular job, have Yamaha dealer perform it for you.
Owner’s tool kit
1
P
6
EAU46862
TI
ed maintenance, or for the UK, a
km (6000 mi). equire special tools, data and tech-
EAU46911
P
N
ADINGANNUAL CHECK
i)30000 km (18000 mi)
40000 km (24000 mi)
1 √ √ √
2√
√
3 0 km (24000 mi)
4 √ √ √
5 √ √
6 √ √ √
U2SGE0E0.book Page 3 Wednesday, June 12, 2013 1:15 PM
ERIODIC MAINTENANCE AND ADJUSTMENT
6-3
P
The annual checks must be performed every year, except if a kilometer-bas
mileage-based maintenance, is performed instead.
From 50000 km (30000 mi), repeat the maintenance intervals starting from 10000 Items marked with an asterisk should be performed by a Yamaha dealer as they rnical skills.
eriodic maintenance chart for the emission control system
O. ITEM CHECK OR MAINTENANCE JOB
ODOMETER RE
1000 km (600 mi)
10000 km (6000 mi)
20000 km(12000 m
* Fuel line• Check fuel hoses for cracks or
damage. √ √
* Spark plugs
• Check condition.• Clean and regap. √
• Replace. √
* Valves• Check valve clearance.• Adjust. Every 4000
* Fuel injection sys-tem
• Adjust synchronization. √ √ √
* Mufflers and ex-haust pipes
• Check the screw clamps for looseness. √ √ √
* Air induction sys-tem
• Check the air cut-off valve, reed valve, and hose for damage.
• Replace any damaged parts if necessary.
√ √
AND ADJUSTMENT
6
EAU1770G
G
N
EADINGANNUAL CHECKm
i)30000 km (18000 mi)
40000 km (24000 mi)
1 √
2 √ √
3√ √ √
worn to the limit
4√ √ √
worn to the limit
5√ √ √
ry 4 years
6 ry 2 years
7 √ √
8 √ √ √
9 √ √
U2SGE0E0.book Page 4 Wednesday, June 12, 2013 1:15 PM
PERIODIC MAINTENANCE
6-4
eneral maintenance and lubrication chart
O. ITEM CHECK OR MAINTENANCE JOB
ODOMETER R
1000 km (600 mi)
10000 km (6000 mi)
20000 k(12000 m
* Air filter element • Replace.
Clutch• Check operation.• Adjust. √ √ √
* Front brake
• Check operation, fluid level and vehicle for fluid leakage. √ √ √
• Replace brake pads. Whenever
* Rear brake
• Check operation, fluid level and vehicle for fluid leakage. √ √ √
• Replace brake pads. Whenever
* Brake hoses
• Check for cracks or damage.• Check for correct routing and
clamping.√ √
• Replace. Eve
* Brake fluid • Replace. Eve
* Wheels • Check runout and for damage. √ √
* Tires
• Check tread depth and for dam-age.
• Replace if necessary.• Check air pressure.• Correct if necessary.
√ √
* Wheel bearings• Check bearing for looseness or
damage. √ √
P
6
10
√ √
0 km (30000 mi)
11shing the motorcycle, riding in the rain or in wet areas
12
√ √
0 km (12000 mi)
13 √ √
14 √ √ √
15 √ √ √
16 √ √ √
17 √ √ √
18 √ √ √
N
ADINGANNUAL CHECK
i)30000 km (18000 mi)
40000 km (24000 mi)
U2SGE0E0.book Page 5 Wednesday, June 12, 2013 1:15 PM
ERIODIC MAINTENANCE AND ADJUSTMENT
6-5
* Swingarm
• Check operation and for exces-sive play. √ √
• Lubricate with lithium-soap-based grease. Every 5000
Drive chain
• Check chain slack, alignment and condition.
• Adjust and lubricate chain with a special O-ring chain lubricant thoroughly.
Every 800 km (500 mi) and after wariding
* Steering bearings
• Check bearing play and steering for roughness. √ √ √
• Lubricate with lithium-soap-based grease. Every 2000
* Steering damper• Check operation and for oil leak-
age. √ √
* Chassis fasteners• Make sure that all nuts, bolts and
screws are properly tightened. √ √
Brake lever pivot shaft
• Lubricate with silicone grease. √ √
Brake pedal pivot shaft
• Lubricate with lithium-soap-based grease. √ √
Clutch lever pivot shaft
• Lubricate with lithium-soap-based grease. √ √
Shift pedal pivot shaft
• Lubricate with lithium-soap-based grease. √ √
O. ITEM CHECK OR MAINTENANCE JOB
ODOMETER RE
1000 km (600 mi)
10000 km (6000 mi)
20000 km(12000 m
AND ADJUSTMENT
6
1 √ √ √
2 √ √ √
2 √ √
2 √ √
2 √ √
2 √ √ √
2 √
2√ √ √
ry 3 years
2 √ √ √
2 √ √ √
N
EADINGANNUAL CHECKm
i)30000 km (18000 mi)
40000 km (24000 mi)
U2SGE0E0.book Page 6 Wednesday, June 12, 2013 1:15 PM
PERIODIC MAINTENANCE
6-6
9 Sidestand• Check operation.• Lubricate with lithium-soap-
based grease.√ √
0 * Sidestand switch • Check operation. √ √ √
1 * Front fork• Check operation and for oil leak-
age. √ √
2 * Shock absorber as-sembly
• Check operation and shock ab-sorber for oil leakage. √ √
3 *
Rear suspension re-lay arm and con-necting arm pivoting points
• Check operation. √ √
4 Engine oil• Change.• Check oil level and vehicle for oil
leakage.√ √ √
5Engine oil filter car-tridge
• Replace. √ √
6 * Cooling system
• Check coolant level and vehicle for coolant leakage. √ √
• Change coolant. Eve
7 * Front and rear brake switches
• Check operation. √ √ √
8Moving parts and cables
• Lubricate. √ √
O. ITEM CHECK OR MAINTENANCE JOB
ODOMETER R
1000 km (600 mi)
10000 km (6000 mi)
20000 k(12000 m
P
6
EAU18681
TI
hich must not be cleaned with com-
ally wet or dusty areas.
and calipers, and change the brake
29 √ √ √
30 √ √ √
N
ADINGANNUAL CHECK
i)30000 km (18000 mi)
40000 km (24000 mi)
U2SGE0E0.book Page 7 Wednesday, June 12, 2013 1:15 PM
ERIODIC MAINTENANCE AND ADJUSTMENT
6-7
P
Air filter• This model’s air filter is equipped with a disposable oil-coated paper element, w
pressed air to avoid damaging it.• The air filter element needs to be replaced more frequently when riding in unusuHydraulic brake service• Regularly check and, if necessary, correct the brake fluid level.• Every two years replace the internal components of the brake master cylinders
fluid.• Replace the brake hoses every four years and if cracked or damaged.
* Throttle grip
• Check operation.• Check throttle grip free play, and
adjust if necessary.• Lubricate cable and grip housing.
√ √
* Lights, signals and switches
• Check operation.• Adjust headlight beam. √ √ √
O. ITEM CHECK OR MAINTENANCE JOB
ODOMETER RE
1000 km (600 mi)
10000 km (6000 mi)
20000 km(12000 m
AND ADJUSTMENT
6
RinTmnRin
. Disconnect the turn signal lightlead coupler.
1.2.
Quick fastener screw
Cowling ACowling BQuick fastener
1
1
1
3
U2SGE0E0.book Page 8 Wednesday, June 12, 2013 1:15 PM
PERIODIC MAINTENANCE
6-8
EAU18782
emoving and installing cowl-gs
he cowlings shown need to be re-oved to perform some of the mainte-
ance jobs described in this chapter.efer to this section each time a cowl-g needs to be removed and installed.
EAU55920
Cowlings A and B
To remove a cowling1. Remove the quick fastener screws
and the quick fasteners, and thentake the cowling off.
2
Cowling ACowling C
12
1. Cowling B2. Cowling D
21
1.
1.2.3.
2
3
P
6
To1
2
Slide the cowling forward to un-hook its projection from the slot,and then pull the cowling off.
1.
1.2.
owling Cuick fastener screw
lotrojection
22
221
1
2
U2SGE0E0.book Page 9 Wednesday, June 12, 2013 1:15 PM
ERIODIC MAINTENANCE AND ADJUSTMENT
6-9
install a cowling. Connect the turn signal light lead
coupler.. Fit the projections on the cowling
into the slots as shown.
3. Install the quick fasteners and thequick fastener screws.
Cowlings C and D
To remove a cowling1. Remove cowling A (if removing
cowling C) or cowling B (if remov-ing cowling D). (See page 6-8.)
2. Remove the quick fastenerscrews.
3.
Turn signal light lead coupler
SlotProjection
1
2
1
1. Slot2. Projection
12
1. C2. Q
1. S2. P
AND ADJUSTMENT
6
T EAU19653
ecking the spark plugse spark plugs are important enginemponents, which should beecked periodically, preferably by amaha dealer. Since heat and depos- will cause any spark plug to slowlyde, they should be removed and
ecked in accordance with the peri-ic maintenance and lubricationart. In addition, the condition of theark plugs can reveal the condition of engine.e porcelain insulator around thenter electrode of each spark plugould be a medium-to-light tan (theal color when the vehicle is riddenrmally), and all spark plugs installedthe engine should have the samelor. If any spark plug shows a dis-ctly different color, the engine could operating improperly. Do not at-
pt to diagnose such problemsurself. Instead, have a Yamaha deal-check the vehicle.a spark plug shows signs of elec-de erosion and excessive carbon orer deposits, it should be replaced.
1.2.3.
1.2.3.
U2SGE0E0.book Page 10 Wednesday, June 12, 2013 1:15 PM
PERIODIC MAINTENANCE
6-10
o install a cowling1. Insert the projection into the slot,
and then slide the cowling back-ward.
2. Place the cowling in its original po-sition, and then install the quickfastener screws.
3. Install cowling A or B.
ChThcochYaitserochodchsptheThceshidenoin cotinbetemyoer If trooth
Cowling CSlotProjection
Cowling DSlotProjection
2
3
1
3
1
2
P
6
Bespwne
Clgathpl
EAU47282
gine oil and oil filter car-ge engine oil level should be checkedore each ride. In addition, the oilst be changed and the oil filter car-ge replaced at the intervals speci- in the periodic maintenance andrication chart.
check the engine oil level
Place the vehicle on a level sur-face and hold it in an upright posi-tion. A slight tilt to the side canresult in a false reading.Start the engine, warm it up forseveral minutes, and then turn itoff.Wait a few minutes until the oil set-tles, and then check the oil levelthrough the check window locat-ed at the bottom-right side of thecrankcase.
engine oil should be between theimum and maximum level marks.
1.
U2SGE0E0.book Page 11 Wednesday, June 12, 2013 1:15 PM
ERIODIC MAINTENANCE AND ADJUSTMENT
6-11
fore installing a spark plug, theark plug gap should be measured
ith a wire thickness gauge and, ifcessary, adjusted to specification.
ean the surface of the spark plugsket and its mating surface, anden wipe off any grime from the sparkug threads.
TIP
If a torque wrench is not availablewhen installing a spark plug, a goodestimate of the correct torque is 1/4–1/2 turn past finger tight. However, thespark plug should be tightened to thespecified torque as soon as possible.
NOTICEECA10841
Do not use any tools to remove or in-
stall the spark plug cap, otherwise
the ignition coil coupler may get
damaged. The spark plug cap may
be difficult to remove because the
rubber seal on the end of the cap fits
tightly. To remove the spark plug
cap, simply twist it back and forth
while pulling it out; to install it, twist
it back and forth while pushing it in.
EntridThebefmutridfiedlub
To
1.
2.
3.
TIP
Themin
Specified spark plug:NGK/LMAR9E-J
Spark plug gap
Spark plug gap:0.6–0.7 mm (0.024–0.028 in)
Tightening torque:Spark plug:
13 Nm (1.3 m·kgf, 9.4 ft·lbf)
1 1
AND ADJUSTMENT
6
T
w
m
oil filter wrench is available at amaha dealer.
. Apply a thin coat of clean engineoil to the O-ring of the new oil filtercartridge.
1.2.3.4.
Oil filter cartridgeOil filter wrench
1 2
U2SGE0E0.book Page 12 Wednesday, June 12, 2013 1:15 PM
PERIODIC MAINTENANCE
6-12
4. If the engine oil is at or below theminimum level mark, add suffi-cient oil of the recommended typeto raise it to the correct level.
o change the engine oil (with or
ithout oil filter cartridge replace-
ent)
1. Remove cowlings C and D. (Seepage 6-8.)
2. Start the engine, warm it up forseveral minutes, and then turn itoff.
3. Place an oil pan under the engineto collect the used oil.
4. Remove the engine oil filler cap,the engine oil drain bolt and itsgasket to drain the oil from thecrankcase.
TIP
Skip steps 5–7 if the oil filter cartridgeis not being replaced.
5. Remove the oil filter cartridge withan oil filter wrench.
TIP
AnYa
6
Engine oil level check windowMaximum level markMinimum level markEngine oil filler cap
2
4
13
1. Engine oil drain bolt2. Gasket
1
21.2.
P
6
TI
Mse
7
sure to wipe off spilled oil on anyts after the engine and exhaust sys- have cooled down.
TICEECA11621
In order to prevent clutch slip-
page (since the engine oil also
lubricates the clutch), do not
mix any chemical additives. Do
not use oils with a diesel speci-
fication of “CD” or oils of a high-
er quality than specified. In
addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.
Make sure that no foreign mate-
rial enters the crankcase.
1.
ecommended engine oil:See page 8-1.
il quantity:Without oil filter cartridge replace-ment:
3.73 L (3.94 US qt, 3.28 Imp.qt)With oil filter cartridge replacement:
3.93 L (4.15 US qt, 3.46 Imp.qt)
U2SGE0E0.book Page 13 Wednesday, June 12, 2013 1:15 PM
ERIODIC MAINTENANCE AND ADJUSTMENT
6-13
P
ake sure that the O-ring is properlyated.
. Install the new oil filter cartridgewith an oil filter wrench, and thentighten it to the specified torquewith a torque wrench.
8. Install the engine oil drain bolt andits new gasket, and then tightenthe bolt to the specified torque.
9. Refill with the specified amount ofthe recommended engine oil, andthen install and tighten the oil fillercap.
TIP
Be partem
NO
O-ring 1. Torque wrench
Tightening torque:Oil filter cartridge:
17 Nm (1.7 m·kgf, 12 ft·lbf)
Tightening torque:Engine oil drain bolt:
43 Nm (4.3 m·kgf, 31 ft·lbf)
1
R
O
AND ADJUSTMENT
6
1
T
Aoth
N
If
o
c
o
th
1
1
. If the coolant is at or below theminimum level mark, remove thecoolant reservoir cover by remov-ing the bolts, remove the coolantreservoir cap, and then add cool-ant to the maximum level mark.WARNING! Remove only the
coolant reservoir cap. Never at-
tempt to remove the radiator
cap when the engine is hot.
[EWA15162] NOTICE: If coolant is not
available, use distilled water or
soft tap water instead. Do not
use hard water or salt water
since it is harmful to the engine.
If water has been used instead
Coolant reservoirMaximum level markMinimum level mark
1
3
2
U2SGE0E0.book Page 14 Wednesday, June 12, 2013 1:15 PM
PERIODIC MAINTENANCE
6-14
0. Start the engine, and then let it idlefor several minutes while checkingit for oil leakage. If oil is leaking,immediately turn the engine offand check for the cause.
IP
fter the engine is started, the engineil level warning light should go off ife oil level is sufficient.
OTICEECA10402
the oil level warning light flickers
r remains on even if the oil level is
orrect, immediately turn the engine
ff and have a Yamaha dealer check
e vehicle.
1. Turn the engine off, wait a fewminutes until the oil settles, andthen check the oil level and cor-rect it if necessary.
2. Install the cowlings.
EAU20071
CoolantThe coolant level should be checkedbefore each ride. In addition, the cool-ant must be changed at the intervalsspecified in the periodic maintenanceand lubrication chart.
EAU38174
To check the coolant level
1. Place the vehicle on a level sur-face and hold it in an upright posi-tion.
TIP
The coolant level must bechecked on a cold engine sincethe level varies with engine tem-perature.
Make sure that the vehicle is posi-tioned straight up when checkingthe coolant level. A slight tilt to theside can result in a false reading.
2. Check the coolant level in thecoolant reservoir.
TIP
The coolant should be between theminimum and maximum level marks.
3
1.2.3.
P
6
Remove the radiator cap.WARNING! Never attempt to re-
move the radiator cap when the
engine is hot. [EWA10382]
Remove the coolant drain bolt andits gasket to drain the cooling sys-tem.
1.2.
adiator cap
oolant drain boltasket
1
1
2
U2SGE0E0.book Page 15 Wednesday, June 12, 2013 1:15 PM
ERIODIC MAINTENANCE AND ADJUSTMENT
6-15
of coolant, replace it with cool-
ant as soon as possible, other-
wise the cooling system will not
be protected against frost and
corrosion. If water has been
added to the coolant, have a
Yamaha dealer check the anti-
freeze content of the coolant as
soon as possible, otherwise the
effectiveness of the coolant will
be reduced. [ECA10473]
4. Install the reservoir cap, and theninstall the coolant reservoir coverby installing the bolts.
EAU47304
To change the coolant
1. Place the vehicle on a level sur-face and let the engine cool if nec-essary.
2. Remove cowlings B and C. (Seepage 6-8.)
3. Place a container under the en-gine to collect the used coolant.
4.
5.
Coolant reservoir coverBolt
1
2
1. Coolant reservoir cap
Coolant reservoir capacity (up to the maximum level mark):
0.25 L (0.26 US qt, 0.22 Imp.qt)
1
1. R
1. C2. G
AND ADJUSTMENT
6
. Pour the recommended coolantinto the reservoir to the maximumlevel mark, and then install thecoolant reservoir cap.
. Pour the recommended coolantinto the radiator until it is full.
. Install the radiator cap, start theengine, let it idle for several min-utes, and then turn it off.
. Remove the radiator cap to checkthe coolant level in the radiator. Ifnecessary, add sufficient coolantuntil it reaches the top of the radi-ator, and then install the radiatorcap.
1.2.
1.
Antifreeze/water mixture ratio:1:1
Recommended antifreeze:High-quality ethylene glycol anti-freeze containing corrosion inhibi-tors for aluminum engines
Coolant quantity:Radiator capacity (including all routes):
2.73 L (2.89 US qt, 2.40 Imp.qt)Coolant reservoir capacity (up to the maximum level mark):
0.25 L (0.26 US qt, 0.22 Imp.qt)
U2SGE0E0.book Page 16 Wednesday, June 12, 2013 1:15 PM
PERIODIC MAINTENANCE
6-16
6. Remove the coolant reservoir cov-er by removing the bolts, and thenremove the coolant reservoir cap.
7. Remove the coolant reservoir byremoving the bolts, and then turnthe reservoir upside down to emp-ty it.
8. After the coolant is completelydrained, thoroughly flush the cool-ing system with clean tap water.
9. Install the coolant reservoir by in-stalling the bolts.
10. Install the coolant drain bolt andits new gasket, and then tightenthe bolt to the specified torque.
11
12
13
14
Coolant reservoir coverBolt
Coolant reservoir cap
1
2
1
1. Coolant reservoir2. Bolt
Tightening torque:Coolant drain bolt:
7 Nm (0.7 m·kgf, 5.1 ft·lbf)
1
2
P
6
15
16
17
EAU44735
ecking the engine idling eedeck the engine idling speed and, ifessary, have it corrected by aaha dealer.
ngine idling speed:1150–1250 r/min
U2SGE0E0.book Page 17 Wednesday, June 12, 2013 1:15 PM
ERIODIC MAINTENANCE AND ADJUSTMENT
6-17
. Start the engine, and then checkthe vehicle for coolant leakage. Ifcoolant is leaking, have a Yamahadealer check the cooling system.
. Install the coolant reservoir coverby installing the bolts.
. Install the cowlings.
EAU36765
Air filter elementThe air filter element must be replacedat the intervals specified in the periodicmaintenance and lubrication chart.Have a Yamaha dealer replace the airfilter element.
ChspChnecYam
E
AND ADJUSTMENT
6
Cp
Tsincae
EAU21777
reses are the only contact between thehicle and the road. Safety in all con-ions of riding depends on a relativelyall area of road contact. Therefore, itssential to maintain the tires in good
ndition at all times and replace themthe appropriate time with the speci-d tires.
e air pressure
e tire air pressure should beecked and, if necessary, adjustedfore each ride.
WARNING
EWA10504
eration of this vehicle with im-
oper tire pressure may cause se-
re injury or death from loss of
ntrol.
The tire air pressure must be
checked and adjusted on cold
tires (i.e., when the temperature
of the tires equals the ambient
temperature).
The tire air pressure must be
adjusted in accordance with the
riding speed and with the total
1.
U2SGE0E0.book Page 18 Wednesday, June 12, 2013 1:15 PM
PERIODIC MAINTENANCE
6-18
EAU21385
hecking the throttle grip free lay
he throttle grip free play should mea-ure 3.0–5.0 mm (0.12–0.20 in) at thener edge of the throttle grip. Periodi-ally check the throttle grip free playnd, if necessary, have a Yamaha deal-r adjust it.
EAU21402
Valve clearanceThe valve clearance changes with use,resulting in improper air-fuel mixtureand/or engine noise. To prevent thisfrom occurring, the valve clearancemust be adjusted by a Yamaha dealerat the intervals specified in the periodicmaintenance and lubrication chart.
TiTirveditsmis ecoat fie
Tir
Thchbe
Op
pr
ve
co
Throttle grip free play
1
P
6
Ne
tio
ca
WARNING
EWA10472
Have a Yamaha dealer replace
excessively worn tires. Besides
being illegal, operating the vehi-
cle with excessively worn tires
decreases riding stability and
can lead to loss of control.
The replacement of all wheel
and brake-related parts, includ-
ing the tires, should be left to a
Yamaha dealer, who has the
necessary professional knowl-
edge and experience to do so.
Ride at moderate speeds after
changing a tire since the tire
surface must first be “broken
in” for it to develop its optimal
characteristics.
U2SGE0E0.book Page 19 Wednesday, June 12, 2013 1:15 PM
ERIODIC MAINTENANCE AND ADJUSTMENT
6-19
weight of rider, passenger, car-
go, and accessories approved
for this model.
WARNING
EWA10512
ver overload your vehicle. Opera-
n of an overloaded vehicle could
use an accident.
Tire inspection
The tires must be checked before eachride. If the center tread depth reachesthe specified limit, if the tire has a nailor glass fragments in it, or if the side-wall is cracked, have a Yamaha dealerreplace the tire immediately.
TIP
The tire tread depth limits may differfrom country to country. Always com-ply with the local regulations.
Tire air pressure (measured on cold tires):
0–90 kg (0–198 lb):Front:
250 kPa (2.50 kgf/cm², 36 psi)Rear:
290 kPa (2.90 kgf/cm², 42 psi)90–189 kg (198–417 lb):
Front:250 kPa (2.50 kgf/cm², 36 psi)
Rear:290 kPa (2.90 kgf/cm², 42 psi)
High-speed riding:Front:
250 kPa (2.50 kgf/cm², 36 psi)Rear:
290 kPa (2.90 kgf/cm², 42 psi)Maximum load*:
189 kg (417 lb)* Total weight of rider, passenger, car-
go and accessories
1. Tire sidewall2. Tire tread depth
Minimum tire tread depth (front and rear):
1.6 mm (0.06 in)
AND ADJUSTMENT
6
T
TlewTuarucacth
WARNING
EWA10601
is motorcycle is fitted with super-
h-speed tires. Note the following
ints in order to make the most ef-
ient use of these tires.
Use only the specified replace-
ment tires. Other tires may run
the danger of bursting at super
high speeds.
Brand-new tires can have a rel-
atively poor grip on certain road
surfaces until they have been
1.2.3.
Front tire:Size:
120/70 ZR17M/C (58W)Manufacturer/model:
MICHELIN/POWER PURE ADUNLOP/Qualifier II
Rear tire:Size:
190/55 ZR17M/C (75W)Manufacturer/model:
MICHELIN/POWER PUREDUNLOP/Qualifier II
FRONT and REAR:Tire air valve:
TR412Valve core:
#9100 (original)
U2SGE0E0.book Page 20 Wednesday, June 12, 2013 1:15 PM
PERIODIC MAINTENANCE
6-20
ire information
his motorcycle is equipped with tube-ss tires, tire air valves and castheels.ires age, even if they have not beensed or have only been used occasion-lly. Cracking of the tread and sidewallbber, sometimes accompanied by
arcass deformation, is an evidence ofgeing. Old and aged tires shall behecked by tire specialists to ascertaineir suitability for further use.
WARNING
EWA10482
The front and rear tires should
be of the same make and de-
sign, otherwise the handling
characteristics of the motorcy-
cle may be different, which
could lead to an accident.
Always make sure that the valve
caps are securely installed to
prevent air pressure leakage.
Use only the tire valves and
valve cores listed below to
avoid tire deflation during a
high-speed ride.
After extensive tests, only the tires list-ed below have been approved for thismodel by Yamaha Motor Co., Ltd. Th
hig
po
fic
Tire air valveTire air valve coreTire air valve cap with seal
P
6
EAU33892
justing the clutch lever free y
clutch lever free play should mea-e 10.0–15.0 mm (0.39–0.59 in) aswn. Periodically check the clutchr free play and, if necessary, adjust
s follows.increase the clutch lever free play, the clutch lever free play adjusting
t at the clutch lever in direction (a).decrease the clutch lever free play, the adjusting bolt in direction (b).
lutch lever free play adjusting boltlutch lever free play
U2SGE0E0.book Page 21 Wednesday, June 12, 2013 1:15 PM
ERIODIC MAINTENANCE AND ADJUSTMENT
6-21
“broken in”. Therefore, it is ad-
visable before doing any high-
speed riding to ride conserva-
tively for approximately 100 km
(60 mi) after installing a new tire.
The tires must be warmed up
before a high-speed run.
Always adjust the tire air pres-
sure according to the operating
conditions.
EAU21963
Cast wheelsTo maximize the performance, durabil-ity, and safe operation of your vehicle,note the following points regarding thespecified wheels. The wheel rims should be
checked for cracks, bends, warp-age or other damage before eachride. If any damage is found, havea Yamaha dealer replace thewheel. Do not attempt even thesmallest repair to the wheel. A de-formed or cracked wheel must bereplaced.
The wheel should be balancedwhenever either the tire or wheelhas been changed or replaced. Anunbalanced wheel can result inpoor performance, adverse han-dling characteristics, and a short-ened tire life.
Adpla
Thesursholeveit aTo turnbolTo turn
1. C2. C
AND ADJUSTMENT
6
T
Ifca
king performance, which may re-
lt in loss of control and an acci-
nt.
1.2.
U2SGE0E0.book Page 22 Wednesday, June 12, 2013 1:15 PM
PERIODIC MAINTENANCE
6-22
IP
the specified clutch lever free playannot be obtained as describedbove, proceed as follows.
1. Fully turn the adjusting bolt at theclutch lever in direction (a) to loos-en the clutch cable.
2. Loosen the locknut at the crank-case.
3. To increase the clutch lever freeplay, turn the clutch lever free playadjusting nut in direction (a). Todecrease the clutch lever freeplay, turn the adjusting nut in di-rection (b).
4. Tighten the locknut.
EAU37914
Checking the brake lever free play
There should be no free play at thebrake lever end. If there is free play,have a Yamaha dealer inspect thebrake system.
WARNING
EWA14212
A soft or spongy feeling in the brake
lever can indicate the presence of
air in the hydraulic system. If there is
air in the hydraulic system, have a
Yamaha dealer bleed the system be-
fore operating the vehicle. Air in the
hydraulic system will diminish the
bra
su
de
LocknutClutch lever free play adjusting nut
1 2
(a)
(b)
1. No brake lever free play
1
P
6
B
ThthshtarethadTuinligbrjubrju
nt that a wear indicator groove al-st appears, have a Yamaha dealerlace the brake pads as a set.
EAU46292
ar brake pads
h rear brake pad is provided withar indicator grooves, which allow to check the brake pad wear with- having to disassemble the brake.check the brake pad wear, check wear indicator grooves. If a brake has worn to the point that a wear
icator groove almost appears, haveamaha dealer replace the brakes as a set.
1.2.
rake pad wear indicator groove
1
U2SGE0E0.book Page 23 Wednesday, June 12, 2013 1:15 PM
ERIODIC MAINTENANCE AND ADJUSTMENT
6-23
EAU22274
rake light switches
e brake light, which is activated bye brake pedal and brake lever,ould come on just before brakingkes effect. If necessary, adjust thear brake light switch as follows, bute front brake light switch should bejusted by a Yamaha dealer.rn the rear brake light switch adjust-
g nut while holding the rear brakeht switch in place. To make theake light come on earlier, turn the ad-sting nut in direction (a). To make theake light come on later, turn the ad-sting nut in direction (b).
EAU22393
Checking the front and rear brake padsThe front and rear brake pads must bechecked for wear at the intervals spec-ified in the periodic maintenance andlubrication chart.
EAU43063
Front brake pads
The front brake calipers are equippedwith two sets of brake pads.Each front brake pad is provided withone or two wear indicator grooves,which allow you to check the brakepad wear without having to disassem-ble the brake. To check the brake padwear, check the wear indicatorgrooves. If a brake pad has worn to the
poimorep
Re
EacweyououtTo thepadinda Ypad
Rear brake light switchRear brake light switch adjusting nut
1
(a)(b)
2
1. Brake pad wear indicator groove
111. B
1
AND ADJUSTMENT
6
CBisCob
F
Use only the specified brake flu-
id; otherwise, the rubber seals
may deteriorate, causing leak-
age.
Refill with the same type of
brake fluid. Adding a brake fluid
other than DOT 4 may result in a
harmful chemical reaction.
Be careful that water does not
enter the brake fluid reservoir
when refilling. Water will signifi-
cantly lower the boiling point of
the fluid and may result in vapor
lock.
OTICEECA17641
ake fluid may damage painted
rfaces or plastic parts. Always
an up spilled fluid immediately.
the brake pads wear, it is normal for brake fluid level to gradually gown. A low brake fluid level may indi-te worn brake pads and/or brakestem leakage; therefore, be sure toeck the brake pads for wear and theke system for leakage. If the brake
1.
U2SGE0E0.book Page 24 Wednesday, June 12, 2013 1:15 PM
PERIODIC MAINTENANCE
6-24
EAU22582
hecking the brake fluid levelefore riding, check that the brake fluid above the minimum level mark.heck the brake fluid level with the topf the reservoir level. Replenish therake fluid if necessary.
ront brake
Rear brake
WARNING
EWA15991
Improper maintenance can result in
loss of braking ability. Observe
these precautions:
Insufficient brake fluid may al-
low air to enter the brake sys-
tem, reducing braking
performance.
Clean the filler cap before re-
moving. Use only DOT 4 brake
fluid from a sealed container.
N
Br
su
cle
Asthedocasychbra
Minimum level mark
UPPER
LOWER1
1. Minimum level mark
Specified brake fluid:DOT 4
1
P
6
fluYafu
EAU22762
ive chain slack drive chain slack should becked before each ride and adjusted
ecessary.
EAU22775
check the drive chain slack
Place the motorcycle on the side-stand.
en checking and adjusting the drivein slack, there should be no weightthe motorcycle.
Shift the transmission into theneutral position.Measure the drive chain slack asshown.
rive chain slack:25.0–35.0 mm (0.98–1.38 in)
U2SGE0E0.book Page 25 Wednesday, June 12, 2013 1:15 PM
ERIODIC MAINTENANCE AND ADJUSTMENT
6-25
id level goes down suddenly, have amaha dealer check the cause before
rther riding.
EAU22733
Changing the brake fluidHave a Yamaha dealer change thebrake fluid at the intervals specified inthe periodic maintenance and lubrica-tion chart. In addition, have the oil sealsof the master cylinders and calipers aswell as the brake hoses replaced at theintervals listed below or whenever theyare damaged or leaking. Oil seals: Replace every two
years. Brake hoses: Replace every four
years.
DrThecheif n
To
1.
TIP
Whchaon
2.
3.
D
AND ADJUSTMENT
6T
Cju
. Tighten the axle nut, then the lock-nuts to their specified torques.
. Make sure that the drive chainpullers are in the same position,the drive chain slack is correct,and the drive chain movessmoothly.
1.
Tightening torques:Axle nut:
150 Nm (15 m·kgf, 108 ft·lbf)Locknut:
16 Nm (1.6 m·kgf, 12 ft·lbf)
U2SGE0E0.book Page 26 Wednesday, June 12, 2013 1:15 PM
PERIODIC MAINTENANCE
6-26
4. If the drive chain slack is incorrect,adjust it as follows.
EAU34318
o adjust the drive chain slack
onsult a Yamaha dealer before ad-sting the drive chain slack.1. Loosen the axle nut and the lock-
nut on each side of the swingarm.2. To tighten the drive chain, turn the
drive chain slack adjusting bolt oneach side of the swingarm in di-rection (a). To loosen the drivechain, turn the adjusting bolt oneach side of the swingarm in di-rection (b), and then push the rearwheel forward. NOTICE: Improp-
er drive chain slack will over-
load the engine as well as other
vital parts of the motorcycle and
can lead to chain slippage or
breakage. To prevent this from
occurring, keep the drive chain
slack within the specified limits.
[ECA10572]
TIP
Using the alignment marks on eachside of the swingarm, make sure thatboth drive chain pullers are in the sameposition for proper wheel alignment.
3
4
Drive chain slack
1
1. Axle nut2. Drive chain puller3. Drive chain slack adjusting bolt4. Locknut5. Alignment marks
(b)
(a)
5
1 2 3 4
P
6
CdrThluthtioouwfo
N
Th
af
in
1
23
EAU23098
ecking and lubricating the bles operation of all control cables and condition of the cables should becked before each ride, and the ca-s and cable ends should be lubri-ed if necessary. If a cable is
aged or does not move smoothly,e a Yamaha dealer check or re-ce it. WARNING! Damage to the
er housing of cables may result
internal rusting and cause inter-
ence with cable movement. Re-
ce damaged cables as soon as
sible to prevent unsafe condi-
s. [EWA10712]
ecommended lubricant:Yamaha cable lubricant or other suitable cable lubricant
U2SGE0E0.book Page 27 Wednesday, June 12, 2013 1:15 PM
ERIODIC MAINTENANCE AND ADJUSTMENT
6-27
EAU23026
leaning and lubricating the ive chaine drive chain must be cleaned and
bricated at the intervals specified ine periodic maintenance and lubrica-n chart, otherwise it will quickly weart, especially when riding in dusty or
et areas. Service the drive chain asllows.
OTICEECA10584
e drive chain must be lubricated
ter washing the motorcycle, riding
the rain or riding in wet areas.
. Clean the drive chain with kero-sene and a small soft brush.NOTICE: To prevent damaging
the O-rings, do not clean the
drive chain with steam cleaners,
high-pressure washers or inap-
propriate solvents. [ECA11122]
. Wipe the drive chain dry.
. Thoroughly lubricate the drivechain with a special O-ring chainlubricant. NOTICE: Do not use
engine oil or any other lubri-
cants for the drive chain, as they
may contain substances that
could damage the O-rings.
[ECA11112]
ChcaThethecheblecatdamhavplaout
in
fer
pla
pos
tion
R
AND ADJUSTMENT
6
CthTsaescTruiscctepccc
Recommended lubricant:Lithium-soap-based grease
U2SGE0E0.book Page 28 Wednesday, June 12, 2013 1:15 PM
PERIODIC MAINTENANCE
6-28
EAU23115
hecking and lubricating the rottle grip and cable
he operation of the throttle griphould be checked before each ride. Inddition, the cable should be lubricat-d by a Yamaha dealer at the intervalspecified in the periodic maintenancehart.he throttle cable is equipped with abber cover. Make sure that the cover securely installed. Even though theover is installed correctly, it does notompletely protect the cable from wa-r entry. Therefore, use care not toour water directly onto the cover orable when washing the vehicle. If theable or cover becomes dirty, wipelean with a moist cloth.
EAU44275
Checking and lubricating the brake and shift pedalsThe operation of the brake and shiftpedals should be checked before eachride, and the pedal pivots should be lu-bricated if necessary.
Brake pedal
Shift pedal
P
6
CbrThlevridbr
Br
C
EAU23203
ecking and lubricating the estand
operation of the sidestand shouldchecked before each ride, and theestand pivot and metal-to-metaltact surfaces should be lubricated
ecessary.
WARNING
EWA10732
he sidestand does not move up
down smoothly, have a Yamaha
ler check or repair it. Otherwise,
sidestand could contact the
und and distract the operator, re-
ting in a possible loss of control.
ecommended lubricant:Lithium-soap-based grease
U2SGE0E0.book Page 29 Wednesday, June 12, 2013 1:15 PM
ERIODIC MAINTENANCE AND ADJUSTMENT
6-29
EAU23144
hecking and lubricating the ake and clutch leverse operation of the brake and clutchers should be checked before eache, and the lever pivots should be lu-icated if necessary.
ake lever
lutch lever
Chsid
Thebe sidconif n
If t
and
dea
the
gro
sul
Recommended lubricants:Brake lever:
Silicone greaseClutch lever:
Lithium-soap-based grease
R
AND ADJUSTMENT
6
Lo
Tesa
OTICEECA10591
any damage is found or the front
k does not operate smoothly,
ve a Yamaha dealer check or re-
ir it.
U2SGE0E0.book Page 30 Wednesday, June 12, 2013 1:15 PM
PERIODIC MAINTENANCE
6-30
EAUM1653
ubricating the swingarm piv-ts
he swingarm pivots must be lubricat-d by a Yamaha dealer at the intervalspecified in the periodic maintenancend lubrication chart.
EAU23273
Checking the front forkThe condition and operation of thefront fork must be checked as followsat the intervals specified in the periodicmaintenance and lubrication chart.
To check the condition
Check the inner tubes for scratches,damage and excessive oil leakage.
To check the operation
1. Place the vehicle on a level sur-face and hold it in an upright posi-tion. WARNING! To avoid injury,
securely support the vehicle so
there is no danger of it falling
over. [EWA10752]
2. While applying the front brake,push down hard on the handle-bars several times to check if thefront fork compresses and re-bounds smoothly.
N
If
for
ha
pa
Recommended lubricant:Lithium-soap-based grease
P
6
CWcaoflopech
1
2
EAU23292
ecking the wheel bearings
front and rear wheel bearings mustchecked at the intervals specified in periodic maintenance and lubrica- chart. If there is play in the wheel or if the wheel does not turn
oothly, have a Yamaha dealerck the wheel bearings.
U2SGE0E0.book Page 31 Wednesday, June 12, 2013 1:15 PM
ERIODIC MAINTENANCE AND ADJUSTMENT
6-31
EAU23284
hecking the steeringorn or loose steering bearings mayuse danger. Therefore, the operation the steering must be checked as fol-ws at the intervals specified in theriodic maintenance and lubricationart.. Place a stand under the engine to
raise the front wheel off theground. (See page 6-38 for moreinformation.) WARNING! To
avoid injury, securely support
the vehicle so there is no danger
of it falling over. [EWA10752]
. Hold the lower ends of the frontfork legs and try to move them for-ward and backward. If any freeplay can be felt, have a Yamahadealer check or repair the steer-ing.
Ch
Thebe thetionhubsmche
AND ADJUSTMENT
6
B
TsT(VTlythbe
KEEP THIS AND ALL BATTER-
IES OUT OF THE REACH OF
CHILDREN.
WARNING
EWA16091
move the battery cover by remov-
the bolts and the quick fastener
rews before servicing the battery.
e cover material can conduct
ctricity. If the cover has not been
oved, touching the cover and
battery positive terminal at the
me time with a tool will cause a
ort circuit and sparks.
charge the battery
ve a Yamaha dealer charge the bat-y as soon as possible if it seems tove discharged. Keep in mind that thettery tends to discharge more quick-if the vehicle is equipped with op-nal electrical accessories.
1.2.3.4.5.6.
2
U2SGE0E0.book Page 32 Wednesday, June 12, 2013 1:15 PM
PERIODIC MAINTENANCE
6-32
EAU51961
attery
he battery is located under the ridereat. (See page 3-27.)his model is equipped with a VRLAalve Regulated Lead Acid) battery.
here is no need to check the electro-te or to add distilled water. However,e battery lead connections need toe checked and, if necessary, tight-ned.
WARNING
EWA10761
Electrolyte is poisonous and
dangerous since it contains sul-
furic acid, which causes severe
burns. Avoid any contact with
skin, eyes or clothing and al-
ways shield your eyes when
working near batteries. In case
of contact, administer the fol-
lowing FIRST AID.
• EXTERNAL: Flush with plenty
of water.
• INTERNAL: Drink large quan-
tities of water or milk and im-
mediately call a physician.
• EYES: Flush with water for 15
minutes and seek prompt
medical attention.
Batteries produce explosive hy-
drogen gas. Therefore, keep
sparks, flames, cigarettes, etc.,
away from the battery and pro-
vide sufficient ventilation when
charging it in an enclosed
space.
Re
ing
sc
Th
ele
rem
the
sa
sh
To
Haterhabaly tio
BoltQuick fastener screwPositive battery lead (red)Battery coverBatteryNegative battery lead (black)
1
6 5 4
3
2
P
6
N
To
Le
st
qu
ch
To
1
2
3
EAU49824
placing the fuses main fuse, the fuel injection sys- fuse, and the fuse boxes, whichtain the fuses for the individual cir-
ts, are located under the rider seat.e page 3-27.)
uel injection system fuseuel injection system spare fuseuse boxain fuse
1 23 4
U2SGE0E0.book Page 33 Wednesday, June 12, 2013 1:15 PM
ERIODIC MAINTENANCE AND ADJUSTMENT
6-33
OTICEECA16522
charge a VRLA (Valve Regulated
ad Acid) battery, a special (con-
ant-voltage) battery charger is re-
ired. Using a conventional battery
arger will damage the battery.
store the battery
. If the vehicle will not be used formore than one month, remove thebattery, fully charge it, and thenplace it in a cool, dry place.NOTICE: When removing the
battery, be sure the key is
turned to “OFF”, then discon-
nect the negative lead before
disconnecting the positive lead.
[ECA16303]
. If the battery will be stored formore than two months, check it atleast once a month and fullycharge it if necessary.
. Fully charge the battery before in-stallation. NOTICE: When install-
ing the battery, be sure the key
is turned to “OFF”, then connect
the positive lead before con-
necting the negative lead. [ECA16841]
4. After installation, make sure thatthe battery leads are properly con-nected to the battery terminals.
NOTICEECA16531
Always keep the battery charged.
Storing a discharged battery can
cause permanent battery damage.
ReThetemconcui(Se
1. F2. F3. F4. M
AND ADJUSTMENT
6
T
Tfup
. Turn the key to “ON” and turn onthe electrical circuit in question tocheck if the device operates.
. If the fuse immediately blowsagain, have a Yamaha dealercheck the electrical system.
1.2.3.4.
5.6.7.8.9.10
Specified fuses:Main fuse:
50.0 AHeadlight fuse:
20.0 ASignaling system fuse:
7.5 AIgnition fuse:
15.0 ARadiator fan fuse:
10.0 A × 2Turn signal light fuse:
7.5 ASteering damper fuse:
7.5 AFuel injection system fuse:
15.0 ABackup fuse:
7.5 AElectronic throttle valve fuse:
7.5 A
U2SGE0E0.book Page 34 Wednesday, June 12, 2013 1:15 PM
PERIODIC MAINTENANCE
6-34
IP
o access the fuel injection systemse, remove the starter relay cover byulling it upward.
If a fuse is blown, replace it as follows.1. Turn the key to “OFF” and turn off
the electrical circuit in question.2. Remove the blown fuse, and then
install a new fuse of the specifiedamperage. WARNING! Do not
use a fuse of a higher amperage
rating than recommended to
avoid causing extensive dam-
age to the electrical system and
possibly a fire. [EWA15132]
3
4
Ignition fuseSignaling system fuseElectronic throttle valve fuseBackup fuse (for clock and immobilizer sys-tem)Right radiator fan fuseLeft radiator fan fuseSpare fuseTurn signal light fuseSteering damper fuse.Headlight fuse
6 5 4 3 2 1
9 1087
7
1. Starter relay cover2. Fuel injection system fuse3. Fuel injection system spare fuse
1
2 3
P
6
RThbubu
N
Ta
in
Unhook the headlight bulb holder,and then remove the burnt-outbulb.
Place a new headlight bulb intoposition, and then secure it withthe bulb holder.
eadlight coupler
eadlight bulbeadlight bulb holder
1
1
2
U2SGE0E0.book Page 35 Wednesday, June 12, 2013 1:15 PM
ERIODIC MAINTENANCE AND ADJUSTMENT
6-35
EAU39014
eplacing a headlight bulbis model is equipped with halogenlb headlights. If a headlight bulbrns out, replace it as follows.
OTICEECA10651
ke care not to damage the follow-
g parts:
Headlight bulb
Do not touch the glass part of
the headlight bulb to keep it free
from oil, otherwise the transpar-
ency of the glass, the luminosity
of the bulb, and the bulb life will
be adversely affected. Thor-
oughly clean off any dirt and fin-
gerprints on the headlight bulb
using a cloth moistened with al-
cohol or thinner.
Headlight lens
Do not affix any type of tinted
film or stickers to the headlight
lens.
Do not use a headlight bulb of a
wattage higher than specified.
1. Remove the headlight bulb coverby turning it counterclockwise.
2. Disconnect the headlight coupler.
3.
4.
1. Do not touch the glass part of the bulb.
1. Headlight bulb cover
1
1. H
1. H2. H
AND ADJUSTMENT
6
EAU24205
placing a turn signal light lb. Remove the turn signal light lens
by removing the screw.
. Remove the burnt-out bulb bypushing it in and turning it coun-terclockwise.
Turn signal light lensScrew
1
2
U2SGE0E0.book Page 36 Wednesday, June 12, 2013 1:15 PM
PERIODIC MAINTENANCE
6-36
5. Connect the headlight coupler.6. Install the headlight bulb cover by
turning it clockwise.7. Have a Yamaha dealer adjust the
headlight beam if necessary.
EAU24182
Tail/brake lightThis model is equipped with an LED-type tail/brake light.If the tail/brake light does not come on,have a Yamaha dealer check it.
Rebu
1
2
1.2.
P
6
3
4
Remove the burnt-out bulb bypulling it out.Insert a new bulb into the socket.Install the socket (together withthe bulb) by pushing it in.Install the license plate light unit byinstalling the screws.
1. icense plate light bulbicense plate light bulb socket
1
2
U2SGE0E0.book Page 37 Wednesday, June 12, 2013 1:15 PM
ERIODIC MAINTENANCE AND ADJUSTMENT
6-37
. Insert a new bulb into the socket,push it in, and then turn it clock-wise until it stops.
. Install the lens by installing thescrew. NOTICE: Do not over-
tighten the screw, otherwise the
lens may break. [ECA11192]
EAU24314
Replacing the license plate light bulb
1. Remove the license plate light unitby removing the screws.
2. Remove the license plate lightbulb socket (together with thebulb) by pulling it out.
3.
4.5.
6.
Turn signal light bulb
1
1. License plate light unit2. Screw
1
2
1. L2. L
AND ADJUSTMENT
6
A
TaIfh
jack either under each side of theme in front of the rear wheel or underch side of the swingarm.
1.
U2SGE0E0.book Page 38 Wednesday, June 12, 2013 1:15 PM
PERIODIC MAINTENANCE
6-38
EAU54501
uxiliary light
his model is equipped with LED-typeuxiliary lights. an auxiliary light does not come on,ave a Yamaha dealer check it.
EAU24351
Supporting the motorcycleSince this model is not equipped with acenterstand, follow these precautionswhen removing the front and rearwheel or performing other mainte-nance requiring the motorcycle tostand upright. Check that the motorcy-cle is in a stable and level position be-fore starting any maintenance. Astrong wooden box can be placed un-der the engine for added stability.
To service the front wheel
1. Stabilize the rear of the motorcy-cle by using a motorcycle standor, if an additional motorcyclestand is not available, by placing ajack under the frame in front of therear wheel.
2. Raise the front wheel off theground by using a motorcyclestand.
To service the rear wheel
Raise the rear wheel off the ground byusing a motorcycle stand or, if a motor-cycle stand is not available, by placing
a fraea
Auxiliary light
1
P
6
TrAla frodufufoanThrefoseredethknprUsmlikinca
W
no
no
ea
U2SGE0E0.book Page 39 Wednesday, June 12, 2013 1:15 PM
ERIODIC MAINTENANCE AND ADJUSTMENT
6-39
EAU25872
oubleshootingthough Yamaha motorcycles receivethorough inspection before shipmentm the factory, trouble may occurring operation. Any problem in the
el, compression, or ignition systems,r example, can cause poor startingd loss of power.e following troubleshooting chartspresent quick and easy proceduresr checking these vital systems your-lf. However, should your motorcyclequire any repair, take it to a Yamahaaler, whose skilled technicians havee necessary tools, experience, andow-how to service the motorcycleoperly.e only genuine Yamaha replace-
ent parts. Imitation parts may looke Yamaha parts, but they are oftenferior, have a shorter service life andn lead to expensive repair bills.
WARNING
EWA15142
hen checking the fuel system, do
t smoke, and make sure there are
open flames or sparks in the ar-
, including pilot lights from water
heaters or furnaces. Gasoline or
gasoline vapors can ignite or ex-
plode, causing severe injury or prop-
erty damage.
AND ADJUSTMENT
6
EAU42505
T
S
s not start. ry.
hicle.
ehicle.
e engine does not start.eck the compression.
The engine does not start.Check the ignition.
erate the electric starter.
U2SGE0E0.book Page 40 Wednesday, June 12, 2013 1:15 PM
PERIODIC MAINTENANCE
6-40
roubleshooting charts
tarting problems or poor engine performance
Check the fuel level inthe fuel tank.
1. FuelThere is enough fuel.
There is no fuel.
Check the battery.
Supply fuel. The engine doeCheck the batte
Remove the spark plugsand check the electrodes.
3. Ignition Wipe off with a dry cloth and correct thespark plug gaps, or replace the spark plugs.
Have a Yamaha dealer check the vehicle.
Operate the electric starter.
4. CompressionThere is compression.
There is no compression.
The engine does not start. Have a Yamaha dealer check the ve
Have a Yamaha dealer check the v
ThCh
Operate the electric starter.
2. Battery The engine turns over quickly.
The engine turns over slowly.
The battery is good.
Check the battery lead connections,and have a Yamaha dealer charge the battery if necessary.
Dry
Wet Op
P
6
EnEWAT1041
ding hot fluid and steam may be
until the engine has cooled.
the cap counterclockwise to the
stopped, press down on the cap
TI
If hanged to the recommended cool-an
Have a Yamaha dealer checkand repair the cooling system.
Add coolant. (See TIP.)
f the engine overheats again, have a eck and repair the cooling system.
ise.
is kage.
U2SGE0E0.book Page 41 Wednesday, June 12, 2013 1:15 PM
ERIODIC MAINTENANCE AND ADJUSTMENT
6-41
gine overheating
WARNING
Do not remove the radiator cap when the engine and radiator are hot. Scal
blown out under pressure, which could cause serious injury. Be sure to wait
Place a thick rag, like a towel, over the radiator cap, and then slowly rotate
detent to allow any residual pressure to escape. When the hissing sound has
while turning it counterclockwise, and then remove the cap.
P
coolant is not available, tap water can be temporarily used instead, provided that it is ct as soon as possible.
Wait until the engine has cooled.
Check the coolant level in the reservoir and radiator.
The coolant level is OK.
The coolant level is low.Check the cooling systemfor leakage.
Start the engine. IYamaha dealer ch
There leakag
There no lea
ARE AND STORAGE
7
M
N
S
m
s
a
fo
b
c
th
th
b
is
ucts onto seals, gaskets, sprock-ets, the drive chain and wheelaxles. Always rinse the dirt anddegreaser off with water.
eaning
OTICEECA15093
Avoid using strong acidic wheel
cleaners, especially on spoked
wheels. If such products are
used on hard-to-remove dirt, do
not leave the cleaner on the af-
fected area any longer than in-
structed. Also, thoroughly rinse
the area off with water, immedi-
ately dry it, and then apply a cor-
rosion protection spray.
Improper cleaning can damage
plastic parts (such as cowlings,
panels, windshields, headlight
lenses, meter lenses, etc.) and
the mufflers. Use only a soft,
clean cloth or sponge with wa-
ter to clean plastic. However, if
the plastic parts cannot be thor-
oughly cleaned with water, di-
luted mild detergent with water
may be used. Be sure to rinse
U2SGE0E0.book Page 1 Wednesday, June 12, 2013 1:15 PM
MOTORCYCLE C
7-1
EAU37834
atte color caution
OTICEECA15193
ome models are equipped with
atte colored finished parts. Be
ure to consult a Yamaha dealer for
dvice on what products to use be-
re cleaning the vehicle. Using a
rush, harsh chemical products or
leaning compounds when cleaning
ese parts will scratch or damage
eir surface. Wax also should not
e applied to any matte colored fin-
hed parts.
EAU58090
CareWhile the open design of a motorcyclereveals the attractiveness of the tech-nology, it also makes it more vulnera-ble. Rust and corrosion can developeven if high-quality components areused. A rusty exhaust pipe may go un-noticed on a car, however, it detractsfrom the overall appearance of a mo-torcycle. Frequent and proper caredoes not only comply with the terms ofthe warranty, but it will also keep yourmotorcycle looking good, extend itslife and optimize its performance.
Before cleaning
1. Cover the muffler outlets with aplastic bag after the engine hascooled down.
2. Make sure that all caps and cov-ers as well as all electrical cou-plers and connectors, includingthe spark plug caps, are tightly in-stalled.
3. Remove extremely stubborn dirt,like oil burnt onto the crankcase,with a degreasing agent and abrush, but never apply such prod-
Cl
N
M
7
t sprayed on roads in the wintery remain well into spring.
Clean the motorcycle with coldwater and a mild detergent, afterthe engine has cooled down.NOTICE: Do not use warm wa-
ter since it increases the corro-
sive action of the salt. [ECA10792]
After drying the motorcycle, applya corrosion protection spray on allmetal, including chrome- andnickel-plated, surfaces (except thetitanium mufflers) to prevent cor-rosion.
aning the windshieldid using any alkaline or strong acid
aner, gasoline, brake fluid, or anyer solvent. Clean the windshieldh a cloth or sponge dampened withild detergent, and then wash it off
roughly with water. For additionalaning, use Yamaha Windshieldaner or another high-quality wind-eld cleaner. Some cleaning com-nds for plastics may leave
atches on the windshield. Before
U2SGE0E0.book Page 2 Wednesday, June 12, 2013 1:15 PM
OTORCYCLE CARE AND STORAGE
7-2
off any detergent residue using
plenty of water, as it is harmful
to plastic parts.
Do not use any harsh chemical
products on plastic parts or the
mufflers. Be sure to avoid using
cloths or sponges which have
been in contact with strong or
abrasive cleaning products, sol-
vent or thinner, fuel (gasoline),
rust removers or inhibitors,
brake fluid, antifreeze or elec-
trolyte.
Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
storage compartments, electric
components (couplers, connec-
tors, instruments, switches and
lights), breather hoses and
vents.
For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning
compounds for plastic may
leave scratches on the wind-
shield. Test the product on a
small hidden part of the wind-
shield to make sure that it does
not leave any marks. If the wind-
shield is scratched, use a quality
plastic polishing compound af-
ter washing.
After normal useRemove dirt with warm water, a milddetergent, and a soft, clean sponge,and then rinse thoroughly with cleanwater. Use a toothbrush or bottlebrushfor hard-to-reach areas. Stubborn dirtand insects will come off more easily ifthe area is covered with a wet cloth fora few minutes before cleaning.
After riding in the rain, near the sea oron salt-sprayed roadsSince sea salt or salt sprayed on roadsduring winter are extremely corrosivein combination with water, carry outthe following steps after each ride inthe rain, near the sea or on salt-sprayed roads.
TIP
Salma
1.
2.
CleAvocleothwita mthocleCleshipouscr
ARE AND STORAGE
7
uwvre
CTms
WARNING
EWA11132
ntaminants on the brakes or tires
n cause loss of control.
Make sure that there is no oil or
wax on the brakes or tires.
If necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or
acetone, and wash the tires with
warm water and a mild deter-
gent. Before riding at higher
speeds, test the motorcycle’s
braking performance and cor-
nering behavior.
OTICEECA10801
Apply spray oil and wax spar-
ingly and make sure to wipe off
any excess.
Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.
Avoid using abrasive polishing
compounds as they will wear
away the paint.
U2SGE0E0.book Page 3 Wednesday, June 12, 2013 1:15 PM
MOTORCYCLE C
7-3
sing such cleaners, test an area of theindshield which does not affect yourisibility and which cannot be easilycognized.
leaning the titanium mufflershis model is equipped with titaniumufflers, which require the following
pecial care. Use only a soft, clean cloth or
sponge with mild detergent andwater to clean the titanium muf-flers. However, if the mufflers can-not be thoroughly cleaned withmild detergent, alkaline productsand a soft brush may be used.
Never use compounds or otherspecial treatments to clean the ti-tanium mufflers, as they will re-move the finish on the outersurface of the mufflers.
Even the smallest amounts of oil,such as from oily towels or finger-prints, will leave stains on the tita-nium mufflers, which can beremoved with a mild detergent.
Note that the thermally induceddiscoloring of the portion of theexhaust pipe leading into the tita-nium mufflers is normal and can-not be removed.
After cleaning
1. Dry the motorcycle with a chamoisor an absorbing cloth.
2. Immediately dry the drive chainand lubricate it to prevent it fromrusting.
3. Use a chrome polish to shinechrome, aluminum and stainless-steel parts.
4. To prevent corrosion, it is recom-mended to apply a corrosion pro-tection spray on all metal,including chrome- and nickel-plat-ed, surfaces.
5. Use spray oil as a universal clean-er to remove any remaining dirt.
6. Touch up minor paint damagecaused by stones, etc.
7. Wax all painted surfaces.8. Let the motorcycle dry completely
before storing or covering it.
Co
ca
N
M
7
TI
Fill up the fuel tank and add fuelstabilizer (if available) to preventthe fuel tank from rusting and thefuel from deteriorating.Perform the following steps toprotect the cylinders, piston rings,etc. from corrosion.a. Remove the spark plug caps
and spark plugs.b. Pour a teaspoonful of engine
oil into each spark plug bore.c. Install the spark plug caps onto
the spark plugs, and thenplace the spark plugs on thecylinder head so that the elec-trodes are grounded. (This willlimit sparking during the nextstep.)
d. Turn the engine over severaltimes with the starter. (This willcoat the cylinder walls with oil.)WARNING! To prevent dam-
age or injury from sparking,
make sure to ground the
spark plug electrodes while
turning the engine over.
[EWA10952]
U2SGE0E0.book Page 4 Wednesday, June 12, 2013 1:15 PM
OTORCYCLE CARE AND STORAGE
7-4
P
Consult a Yamaha dealer for ad-vice on what products to use.Washing, rainy weather or humidclimates can cause the headlightlens to fog. Turning the headlighton for a short period of time willhelp remove the moisture from thelens.
EAU26204
Storage
Short-term
Always store your motorcycle in a cool,dry place and, if necessary, protect itagainst dust with a porous cover. Besure the engine and the exhaust sys-tem are cool before covering the mo-torcycle.
NOTICEECA10811
Storing the motorcycle in a
poorly ventilated room or cover-
ing it with a tarp, while it is still
wet, will allow water and humid-
ity to seep in and cause rust.
To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-
cals are stored.
Long-term
Before storing your motorcycle for sev-eral months:
1. Follow all the instructions in the“Care” section of this chapter.
2.
3.
ARE AND STORAGE
7
U2SGE0E0.book Page 5 Wednesday, June 12, 2013 1:15 PM
MOTORCYCLE C
7-5
e. Remove the spark plug capsfrom the spark plugs, and theninstall the spark plugs and thespark plug caps.
4. Lubricate all control cables andthe pivoting points of all levers andpedals as well as of the side-stand/centerstand.
5. Check and, if necessary, correctthe tire air pressure, and then liftthe motorcycle so that both of itswheels are off the ground. Alterna-tively, turn the wheels a little everymonth in order to prevent the tiresfrom becoming degraded in onespot.
6. Cover the muffler outlets withplastic bags to prevent moisturefrom entering them.
7. Remove the battery and fullycharge it. Store it in a cool, dryplace and charge it once a month.Do not store the battery in an ex-cessively cold or warm place [lessthan 0 °C (30 °F) or more than 30°C (90 °F)]. For more informationon storing the battery, see page6-32.
TIP
Make any necessary repairs beforestoring the motorcycle.
S
8
Di
W
En
l:ecommended fuel:
Premium unleaded gasoline (Gasohol (E10) acceptable)
uel tank capacity:18.0 L (4.76 US gal, 3.96 Imp.gal)
uel reserve amount:3.1 L (0.82 US gal, 0.68 Imp.gal)
l injection:hrottle body:
ID mark:1KB8 00
rk plug(s):anufacturer/model:NGK/LMAR9E-J
park plug gap:0.6–0.7 mm (0.024–0.028 in)
tch:lutch type:Wet, multiple-disc
nsmission:rimary reduction ratio:
1.512 (65/43)inal drive:
Chainecondary reduction ratio:
2.765 (47/17)ransmission type:
Constant mesh 6-speedperation:Left foot operation
ear ratio:1st:
2.533 (38/15)
U2SGE0E0.book Page 1 Wednesday, June 12, 2013 1:15 PM
PECIFICATIONS
8-1
mensions:Overall length:
2070 mm (81.5 in)Overall width:
715 mm (28.1 in)Overall height:
1130 mm (44.5 in)Seat height:
835 mm (32.9 in)Wheelbase:
1415 mm (55.7 in)Ground clearance:
135 mm (5.31 in)Minimum turning radius:
3500 mm (137.8 in)eight:Curb weight:
206 kg (454 lb)gine:Engine type:
Liquid cooled 4-stroke, DOHCCylinder arrangement:
Inline 4-cylinderDisplacement:
998 cm³Bore × stroke:
78.0 × 52.2 mm (3.07 × 2.06 in)Compression ratio:
12.70 : 1Starting system:
Electric starterLubrication system:
Wet sump
Engine oil:Recommended brand:
YAMALUBEType:
SAE 10W-40, 10W-50, 15W-40, 20W-40 or 20W-50
Recommended engine oil grade:API service SG type or higher, JASO standard MA
Engine oil quantity:Without oil filter cartridge replacement:
3.73 L (3.94 US qt, 3.28 Imp.qt)With oil filter cartridge replacement:
3.93 L (4.15 US qt, 3.46 Imp.qt)Cooling system:
Coolant reservoir capacity (up to the maximum level mark):
0.25 L (0.26 US qt, 0.22 Imp.qt)Radiator capacity (including all routes):
2.73 L (2.89 US qt, 2.40 Imp.qt)Air filter:
Air filter element:Oil-coated paper element
FueR
F
F
FueT
SpaM
S
CluC
TraP
F
S
T
O
G
–20 –10 0 10 20 30 40 50 ˚C
10 30 50 70 90 1100 130 ˚F
SAE 20W-50
SAE 20W-40
SAE 15W-40
SAE 10W-40
SAE 10W-50
SPECIFICATIONS
8
C
F
R
Rim size:17M/C x MT6.00
nt brake:Type:
Dual disc brakeOperation:
Right hand operationSpecified brake fluid:
DOT 4ar brake:Type:
Single disc brakeOperation:
Right foot operationSpecified brake fluid:
DOT 4nt suspension:
Type:Telescopic fork
Spring/shock absorber type:Coil spring/oil damper
Wheel travel:120.0 mm (4.72 in)
ar suspension:Type:
Swingarm (link suspension)Spring/shock absorber type:
Coil spring/gas-oil damperWheel travel:
120.0 mm (4.72 in)ctrical system:
Ignition system:TCI
U2SGE0E0.book Page 2 Wednesday, June 12, 2013 1:15 PM
8-2
2nd:2.063 (33/16)
3rd:1.762 (37/21)
4th:1.522 (35/23)
5th:1.364 (30/22)
6th:1.269 (33/26)
hassis:Frame type:
DiamondCaster angle:
24.00 °Trail:
102 mm (4.0 in)ront tire:
Type:Tubeless
Size:120/70 ZR17M/C (58W)
Manufacturer/model:MICHELIN/POWER PURE A
Manufacturer/model:DUNLOP/Qualifier II
ear tire:Type:
TubelessSize:
190/55 ZR17M/C (75W)Manufacturer/model:
MICHELIN/POWER PURE
Manufacturer/model:DUNLOP/Qualifier II
Loading:Maximum load:
189 kg (417 lb)(Total weight of rider, passenger, cargo and accessories)
Tire air pressure (measured on cold
tires):Loading condition:
0–90 kg (0–198 lb)Front:
250 kPa (2.50 kgf/cm², 36 psi)Rear:
290 kPa (2.90 kgf/cm², 42 psi)Loading condition:
90–189 kg (198–417 lb)Front:
250 kPa (2.50 kgf/cm², 36 psi)Rear:
290 kPa (2.90 kgf/cm², 42 psi)High-speed riding:
Front:250 kPa (2.50 kgf/cm², 36 psi)
Rear:290 kPa (2.90 kgf/cm², 42 psi)
Front wheel:Wheel type:
Cast wheelRim size:
17M/C x MT3.50Rear wheel:
Wheel type:Cast wheel
Fro
Re
Fro
Re
Ele
S
8
Ba
He
Bu
U2SGE0E0.book Page 3 Wednesday, June 12, 2013 1:15 PM
PECIFICATIONS
8-3
Charging system:AC magneto
ttery:Model:
YTZ10SVoltage, capacity:
12 V, 8.6 Ahadlight:Bulb type:
Halogen bulblb voltage, wattage × quantity:Headlight:
12 V, 55.0 W × 2Tail/brake light:
LEDFront turn signal light:
12 V, 10.0 W × 2Rear turn signal light:
12 V, 10.0 W × 2Auxiliary light:
LEDLicense plate light:
12 V, 5.0 W × 1Meter lighting:
LEDNeutral indicator light:
LEDHigh beam indicator light:
LEDOil level warning light:
LEDTurn signal indicator light:
LED
Fuel level warning light:LED
Coolant temperature warning light:LED
Engine trouble warning light:LED
Immobilizer system indicator light:LED
Shift timing indicator light:LED
Traction control system indicator/warning light:
LEDFuses:
Main fuse:50.0 A
Headlight fuse:20.0 A
Signaling system fuse:7.5 A
Ignition fuse:15.0 A
Radiator fan fuse:10.0 A × 2
Turn signal light fuse:7.5 A
Fuel injection system fuse:15.0 A
Steering damper fuse:7.5 A
Backup fuse:7.5 A
Electronic throttle valve fuse:7.5 A
CONSUMER INFORMATION
9-1
9
EAU48613
Identification numbersRecord the vehicle identification num-ber and model label information in thespaces provided below for assistancewhen ordering spare parts from aYamaha dealer or for reference in casethe vehicle is stolen.
VEHICLE IDENTIFICATION NUMBER:
MODEL LABEL INFORMATION:
EAU26401
Vehicle identification number
The vehicle identification number isstamped into the steering head pipe.Record this number in the space pro-vided.
TIP
The vehicle identification number isused to identify your motorcycle andmay be used to register your motorcy-cle with the licensing authority in yourarea.
EAU26521
Model label
The model label is affixed to the frameunder the passenger seat. (See page3-27.) Record the information on thislabel in the space provided. This infor-mation will be needed when orderingspare parts from a Yamaha dealer.
1. Vehicle identification number
1
1. Model label
1
U2SGE0E0.book Page 1 Wednesday, June 12, 2013 1:15 PM
IN
AAA
BBB
B
BBBBBB
CCCCCCCCC
DDDDD
EEEEE
odel label .............................................9-1ulti-function meter unit.........................3-8
utral indicator light..............................3-4
l level warning light ..............................3-4
rking ....................................................5-4rt locations ..........................................2-1ss switch...........................................3-19
ar view mirrors ..................................3-30der footrest position, adjusting..........3-30
fety information...................................1-1ats .....................................................3-27ifting ....................................................5-2ift pedal.............................................3-21ift timing indicator light .......................3-7ock absorber assembly, adjusting....3-33
destand ..............................................3-35destand, checking and lubricating.....6-29ark plugs, checking ..........................6-10ecifications .........................................8-1arting the engine..................................5-1art switch ...........................................3-19eering, checking ................................6-31orage ...................................................7-4orage compartment ...........................3-29pporting the motorcycle ...................6-38ingarm pivots, lubricating ................6-30
il/brake light ......................................6-36
U2SGE0E0.book Page 1 Wednesday, June 12, 2013 1:15 PM
DEX
ir filter element ....................................6-17uxiliary light.........................................6-38
attery ..................................................6-32rake and clutch levers, checking and lubricating...........................................6-29rake and shift pedals, checking and lubricating...........................................6-28rake fluid, changing ............................6-25rake fluid level, checking ....................6-24rake lever ............................................3-21rake lever free play, checking.............6-22rake light switches..............................6-23rake pedal...........................................3-22
ables, checking and lubricating .........6-27are ........................................................7-1atalytic converter................................3-27lutch lever...........................................3-20lutch lever free play, adjusting ...........6-21oolant .................................................6-14oolant temperature warning light .........3-5owlings, removing and installing ..........6-8
immer switch ......................................3-19-mode (drive mode) ............................3-18rive chain, cleaning and lubricating....6-27rive chain slack...................................6-25
ngine break-in.......................................5-3ngine idling speed, checking ..............6-17ngine oil and oil filter cartridge ...........6-11ngine stop switch ...............................3-19
Engine trouble warning light................... 3-7F
Front and rear brake pads, checking ... 6-23Front fork, adjusting ............................. 3-31Front fork, checking ............................. 6-30Fuel....................................................... 3-25Fuel consumption, tips for reducing ...... 5-3Fuel level warning light ........................... 3-4Fuel tank breather hose and overflow
hose ................................................... 3-26Fuel tank cap........................................ 3-24Fuses, replacing ................................... 6-33
HHandlebar switches.............................. 3-18Hazard switch....................................... 3-19Headlight bulb, replacing ..................... 6-35Helmet holder ....................................... 3-29High beam indicator light ....................... 3-4Horn switch .......................................... 3-19
IIdentification numbers............................ 9-1Ignition circuit cut-off system............... 3-36Immobilizer system ................................ 3-1Immobilizer system indicator light.......... 3-8Indicator lights and warning lights ......... 3-4
LLicense plate light bulb, replacing........ 6-37Luggage strap holders ......................... 3-35
MMain switch/steering lock....................... 3-2Maintenance and lubrication, periodic ... 6-4Maintenance, emission control
system.................................................. 6-3Matte color, caution ............................... 7-1
MM
NNe
OOi
PPaPaPa
RReRi
SSaSeShShShShSiSiSpSpStStStStStSuSw
TTa
INDEX
V
W
U2SGE0E0.book Page 2 Wednesday, June 12, 2013 1:15 PM
Throttle grip and cable, checking and lubricating........................................... 6-28
Throttle grip free play, checking........... 6-18Tires...................................................... 6-18Tool kit .................................................... 6-2Traction control system........................ 3-22Traction control system indicator/
warning light ......................................... 3-7Traction control system switch ............ 3-19Troubleshooting.................................... 6-39Troubleshooting charts......................... 6-40Turn signal indicator lights ..................... 3-4Turn signal light bulb, replacing ........... 6-36Turn signal switch................................. 3-19
Valve clearance .................................... 6-18Vehicle identification number ................. 9-1
Wheel bearings, checking .................... 6-31Wheels.................................................. 6-21
A5-yoko_Blank.fm Page 1 Thursday, December 8, 2011 2:18 PM
A5-yoko_Blank.fm Page 1 Thursday, December 8, 2011 2:18 PM
PRINTED IN JAPAN2013.06-0.3×1 CR
(E)
DIC183
PRINTED ON RECYCLED PAPER
Original instructions