224.383.00.1 up170 electronic-flush montage cistern

Standards

Approved

Checked Against

Checked Designer

Part No.

Modify

GEBERIT CompetenceCenter Shanghai(China)

Modify

persons or use it for other activities.allowed to copy this or give it to third

Without our written permission nobody is

All rights are reserved for this document.

Modify

00170.586.00.0

Signed by

Scale

1:1

Designed by

Production

Logistics

Purchase

Quality

Paper

Printing

Type:

Dimension:

Color:

Sides:

Colors:

Two sides

WhiteA3+A4

Ruthy 27/08/09Black & Red

Geberit Installation Instruction

/6

80 g/m2

Layout

Released

P2 P3 P4P1P5 P6

Don

't pr

int t

his

rect

angl

e o

ut请

不要

将此

线框

印刷

出来

FFL0

46-60

FFL

103

59

5

16-29

Hf

45

8

0

459

8

55

57

85

465

16-29

Hf

0-4

0

170.586.00.0(00)

46-60

Bend supplied metalstraps and install asrequired.

Hf = Height of flush pipe, dimension

to WC suppliers specification

Left rail in front of right rail.

1 Layout

2 Fasten cistern

Geberit Installation InstructionArt.No.224.383.00.1

All measurements in cm (1 cm = 10 mm)

Hf = Height of flush pipe,dimension to WC suppliers specificationNote:Add necessary precautions in case of condensation risk!

Pages 1 to 3 of this installation instruction shows only the basic layout for front access cistern installation. Page 5 shows additional schematic layout for rear access installation options. Page 6 shows the basic layout for front access brick installation. The cistern and HyTronic actuator can be installed in several different positions. Confirm with the bathroom designer the required installation details or alternatively refer to product brochure. Provision for a sufficiently sized removable service panel is strictly required. This removable panel has to provide full access to the service opening of the cistern. Also consider that the service personnel require sufficient room to perform maintenance through the service opening.

Install a removable access or cover plate centered over the service opening of the cistern. Minimum size W28cm x H14cm.

See electronic components montage sheet for additional information

Waste position to WC suppliers specification. Waste fittings by others.

59

16-29

103

5

Hf

487

0 FFL

55

44

948

42

-1-

If cavity is deeper than 9 cm keep front part of the access opening flush with studs at the front.

If cavity is 9 cm deep keep back of cistern flush with back of stud wall. Cistern can also be reverse mounted.

Assemble and installrail as shown below.

I f cav i t y i s 9cm deep back o f cistern flush with back of studs.

I f cavi ty is deeper than 9cm keep front part of the access opening flush with studs at the front.

0 = FFL = Finished floor level

8

9

Waste

Waste

FFL

0-4

Netz

teil N

TW

C 0

3882 1

84 0

0 0

IN 2

30v/5

0H

z/1

00m

AO

UT 3

.5-4

.2V

=/5

00m

AF1 2

A/2

50V

TH

SE

V

VD

E

964.338.00.0SY03/03

230-240V50-60Hz

Standards

Approved

Checked Against

Checked Designer

Part No.

Modify


Modify




Modify

00

Signed by

Scale

1:1

Designed by

Production

Logistics

Purchase

Quality

Paper

Printing

Type:

Dimension:

Color:

Sides:

Colors:

Two sides

WhiteA3+A4

Black & Red


/6

80 g/m2

Layout

Released

P1P5 P6 P4P2 P3 170.586.00.0

Ruthy 27/08/09

Don

't pr

int t

his

rect

angl

e o

ut请

不要

将此

线框

印刷

出来

4 Flush pipe installation

3 Flush pipe preparation

5 Stop valve installation


-2-

0FFL

Ensure that flush pipe bend is installed plumb.

1/2" female tube bush( not supplied )

Use suppliedgrommet

Flush line befor

Remove servicecover

connecting hose

Hexagon of tube bushto be inside the cistern.

Max. 65

Fully open

oo

Chamfer the insideCut flush pipe bendto required length edge of the cut.

Lubricate o-ring(lubricant supplied)

Push flush pipe over cistern spiggot. Allow for 2 cm clearance when flushpipe bend is adjusted to the requiredinstallation eight Hf . This will alsoprovide for an additional 2 cmadjustment (up or down) if required later.

Push flush pipe over cistern spiggot. Allow for 2 cm clearance when flushpipe bend is adjusted to the requiredinstallation eight Hf . This will alsoprovide for an additional 2 cmadjustment (up or down) if required later.

A B C

DThis procedure is only for the supplied black flushpipe bend and not for the flush pipe adaptor kit

46-60

Left rail in front of right rail.3434

Secure flush pipe bendwith supplied bracket "A".Pipe to be held firmly butshould still be moveable upor down if so required later.

36

Assemble and installrail as shown below.

For a longer flush pipethan the minimum lengthof 16 cm increase theminimum distance of therail by the same amount.eg.: flush pipe 17 cm = rail distance 14 cm

16-29

13-23

Hf0 FFL

A

5

5

16-29

2

Hf

Hf

9090

Standards

Approved

Checked Against

Checked Designer

Part No.

Modify


Modify




Modify

00

Signed by

Scale

1:1

Designed by

Production

Logistics

Purchase

Quality

Paper

Printing

Type:

Dimension:

Color:

Sides:

Colors:

Two sides

WhiteA3+A4

Black & Red


/6

80 g/m2

Layout

Released

P1P5 P6 P4P2 P3 170.586.00.0

Ruthy 27/08/09

Don

't pr

int t

his

rect

angl

e o

ut请

不要

将此

线框

印刷

出来

Fig. 4

B

Fig. 3Fig. 2Fig. 1

6 Testing

9 Kee seal


-3-

Before the wall is closed cistern must be tested.1. Open stop valve (Fig.1).2. Fill cistern and install inner cover (Fig.2A).3. Check water tightness. Insert protection plug into the flush bend opening and secure it with tape. Leave cistern under test (refer to standard) (Fig.3B).4. Final water tightness test. Remove protection plug and empty the cistern completely. (lift flush valve) Insert protection plug and secure it with tape (Fig.4).

The cistern is supplied with two different sized kee seals. The kee seal with an outside diameter of 6 cm seals flush pipe holes in the ceramic sized 5.3 cm to maximum 5.7cm.The kee seal with an outside diameter of 6.7 cm seals flush pipe holes in the ceramic sized 5.6 cm to maximum 6.2 cm.

Flush pipesThe cistern is supplied with a 18 cm long flush pipe for concealed installations. As an accessory longer flush pipes for in-duct installations are available. For installations with an exposed flush pipe there are also a variety of finishes and materials available. Enquire with your supplier.

A

7 Fit tiling template

Fit styrofoamtiling template

Do a final check on the required flush pipe heightHf.

Hf0 FFL

8

Wall sheeting and tiles shall be cut up to the edge of the tiling template.

Access plateThis installation requires an access plate. For product selection refer to product brochure.

Standards

Approved

Checked Against

Checked Designer

Part No.

Modify


Modify




Modify

00

Signed by

Scale

1:1

Designed by

Production

Logistics

Purchase

Quality

Paper

Printing

Type:

Dimension:

Color:

Sides:

Colors:

Two sides

WhiteA3+A4

Black & Red


/6

80 g/m2

Layout

Released

P1P5 P6 P4P2 P3 170.586.00.0

Ruthy 27/08/09

Don

't pr

int t

his

rect

angl

e o

ut请

不要

将此

线框

印刷

出来

-4-

If the 224.383.00.1 is installed elevated and requires a longer flush pipe use the supplied Adaptor kit. To fabricate the required length see (Fig.A & B).

The adaptor kit includes only the adaptor socket & spacer, the required 40mm DWV pipe & bend are not supplied.

Note: With 40 mm DWV PVC pipe the supplied Geberit kee seals will seal 0.1 cm less than the maximum diameters stated on page 3 in section 10 of the 224.383.00.1 installation instructions.If the adaptor kit is used then the supplied black flush pipe bend and flush pipe are no longer required. Do not attempt to join these parts to PVC.

Adaptor supplied

4 0 D W VP V C Pipenot supplied

4 0 D W V P V C b e n d not supplied

40 DWV PVC Pipe connection to toilet not supplied

fig.A

Push flush pipe adaptor over cistern spiggot. Allow for 3 cm clearance whenflush pipe is adjusted to the requiredinstallation height Hf . This will also provide for an additional 1 cm adjustment(up or down) if required later on in theconstruction.

5

43

Hf

Outlet spigot 224.383 cistern

Lubricate o- rings lubricant supplied

Adaptor Kit Art.No.225.057.00.1

Install black spacerbetween PVC pipeand pipe bracket

Pipe bracket suppliedwith cistern

fig. B

40 DWV PVC pipe workjointed this side


10 Flush pipe adaptor kit

Standards

Approved

Checked Against

Checked Designer

Part No.

Modify


Modify




Modify

00

Signed by

Scale

1:1

Designed by

Production

Logistics

Purchase

Quality

Paper

Printing

Type:

Dimension:

Color:

Sides:

Colors:

Two sides

WhiteA3+A4

Black & Red


/6

80 g/m2

Layout

Released

P1P5 P6 P4P2 P3 170.586.00.0

Ruthy 27/08/09

Don

't pr

int t

his

rect

angl

e o

ut请

不要

将此

线框

印刷

出来


-5-

Install hoses & hardware for Control Panel in preferred location: A, B or C(see also HyTronic installation instructions)

Further Installation Examples

The 224.383.00.1 cistern allows for greater flexibility in the positioning of cistern and HyTronic actuator. See following installation examples. Confirm with the bathroom designer the required installation details or alternatively refer to product brochure. Provision for a sufficiently sized removable service panel is strictly required.

Stud wall installation with rear access (for floor mounted wall faced pan)Cavity depth 9 cm

Note all other installation dimensions and steps are as 2 to 10 on page 1 to 3. The only exception is to swivel flush pipe bend 180° .

Adjacent room this side, service opening this side (rear access).

Side viewIf cavity is deeper than 9 cm keep front part of the service opening flush with studs at the rear.

Install a removable access panel centred over the service opening of the cistern. Minimum size W 28cm x H 14cm.

If cavity is 9 cm deep keep back of cistern flush with front of stud wall.

Bathroom this side

Turn flush pipe bend to this side.

Rear view Side view

Hf= Height of flush pipe, dimension to WC suppliers specification

View from Bathroom View from Bathroom View from Bathroom

HyTronic top mounted HyTronic corner mountedHyTronic side mounted

FFL0

B

FFLHf

46-60

45

103

59

7

16-29

FFL

9

Waste

Waste

FFL0

or Left RightA

C

Right or Left

Bathroom this side

Brackets supplied

55

16-29

459

Hf

5

85

465

87

FFL

Note: Children may have problems reaching the button.

Standards

Approved

Checked Against

Checked Designer

Part No.

Modify


Modify




Modify

00

Signed by

Scale

1:1

Designed by

Production

Logistics

Purchase

Quality

Paper

Printing

Type:

Dimension:

Color:

Sides:

Colors:

Two sides

WhiteA3+A4

Black & Red


/6

80 g/m2

Layout

Released

P1P5 P6 P4P2 P3 170.586.00.0

Ruthy 27/08/09

Don

't pr

int t

his

rect

angl

e o

ut请

不要

将此

线框

印刷

出来


-6-

Brick wall installation (with floor mounted wall faced pan) order Art.No.813.362.00.1 with cistern

HfFFL Waste

Allow for sufficient blockout for cistern installation

Fasten cistern andflush pipe to brick wall

Install Styrofoam PackingArt.No. 813.362.00.1

Note: All other installationdimension are as per stud wallinsta l lat ion and aremeasured from the finished floor

Fill in space betweencistern and wall

Fix rendering mesh Render and tile

Tape gaps

Removable accesscover plate of panel has to be provided

Hf=Height of Flush pipe connection depends on the to toilet model.

Note:All construction dimensions, material, methods and details shown are indicative only. The final sizing, material used and construction methods must be determined by Project Architects, Builder, Engineer and local standard. This edition ; Date:27.8.2009; File name: supercedes all previous editions.

0

Use package tube Art. No: 225.056.00.1 (not supplied)

1

42 3

In-ceiling installation, separate ceiling access.

Cistern serviceopening

FFL

Waste

Hf

Approx. 1m

Ceiling Void

ServicePanel or alternative access

Min. 90mm

Max. 3.5m

Side View Front View

Water connection ½” male

Use extension set Art. No. 117.041.00.1where necessary(max. 3.3m)

PVC Adaptor

Flush pipe 40mm DWV PVC (not provided)

Max.45º bend

Hf

Hf= Height of flush pipe, dimension to WC suppliers specification

224.383.00.1 up170 electronic-flush montage cistern

Documents