problems on piles
Post on 17-Nov-2014
878 Views
Preview:
TRANSCRIPT
PROBLEMS ON PILES/DEEP FOOTING
Problem # 01A cast in place concrete pile in medium sand is 0.5 m in dia and 10 m long. The water table is 2 m below the top of the pile. The bulk density of sand above the water table is 1.8 t/m3 . and below the water table the density is 1.95 t/m3 . Angle of shearing resistance is 38o . Assume Nqp = 60 and ks tan = 0.5, Dc /B = 8. Determine the ultimate load and the safe load for a pile with F.S = 3.
SolutionQf = Qb + Qs
(1) Base resistence (Qb )
B = 0.5 m Lp= 10 m
Nqp = 60 Dc = ? From table
for medium sand, Dc = 8 x B = 8 x 0.5 = 4 m
Lp > Dc .
fb = o Nqp Where o = Effective vertical pressure at Dc .
o = (1.8 x 9.8 x 2) + ( (1.95-1) x 9.8 x 2) = 53.9 kPa.
fb = 53.9 x 60 = 3234 kPa.
Qb = Ab x fb = /4 B2 x fb . = /4 x (0.5)2 x 3234 = 635 kN.
2 mDc = 4 m
• (ii) Frictional resistence, Qs
Qs = As x fs
fs =?
The frictional resistence is calculted by considering the pile in three parts, 0-2m, 2 m - 4 m (Dc ) and 4 m –
10 m. The frictional resistence will increase upto Dc only = 4 m.
at 2 m = 2 x 1.8 x 9.8 = 35.28 kPa. at 4 m = (35.28 + ( 1.95- 1) x 9.8 x 2) = 53.9 kPa.Average vertical stress for 0-2 m = 17.64 kPa. ( 0+ 35.28/2) Av. fs1 =17.64 x ks tan = 17.64 x 0.5 = 8.82 kPa.
Av. Stress for 2 m to 4 m = 53.9 + 35.28/2 = 44.59 kPa. Av. fs2 = s x ks tan = 44.59 x 0.5 = 22.3 kPa.
• Vertical stress below Dc is assumed constant and equal to 53.9 kPa.
• fs3 = 53.9 x 0.5 = 26.95 ( unit skin friction)
• Qs = fs1 x B x D1 + fs2 x B (Dc – D1) + fs3 B (Lp - Dc )• = 8.82 x x 0.5 x 2 + 22.3 x x 0.5 x 2 +26.95
x 0.5 x 6 = 352 kN.• Qf = Qb + Qs = 635 + 352 = 987 kN.
• Qa = Qf /3 = 987/3 = 329 kN.
Problem # 02
• A cased concrete pile, 0.42 m outside diameter, is driven through 11 m of loose sand and for a depth of 3 m into underlying medium dense sand. The skin friction is measured with a static cone fitted with a friction sleeve; fs = fc(av) = 20 kPa in loose sand and fs = fc(av) = 55 kPa in medium dense sand. The cone resistence at base level is 12000 kPa. Determine the safe load for a pile, using F.S = 2.5.
Solution
• Qf = Qb + Qs
• Qb = /4 B2 x fb fb = qc = 12000 kPa but limit is 11000 kPa
• Qb = /4 (0.42)2 x 11000 = 1524 kN.
• Qs = Qs1 + Qs2 ,Qs1 = through loose sand = 11m• Qs2 = through medium dense sand =3 m.• Qs = B x 11 x 20 + B x 3 x 55• = x 0.42 x 11 x 20 + x 0.42 x 3 X 55 = 290.28 + 217.71• Qf = Qb + Qs = 1524 + 290.28 + 217.71= 2032.0 kN.
• Qa = Qf /2.5 = 2032/2.5 = 812.8 kN.
Problem # 03
• Determine the penetration depth for a 40 cm dia. Concrete pile which is required to carry load of 900 kN at a safety factor of 2.5. The soil consists of silty sand upto a depth of 10 m in which the average cone resistance (qc)av = 4000 kPa. Silty sand is underlain by dense sand. The average cone resistance increases to 13000 kPa within the depth 10 m to 10.5 m and to 18000 kPa below 10.5 m. to reach full base resistance the pile must be driven to at least 5B, i-e 2 m, in bearing stratum of dense sand.
Solution
• Try the allowable load for a pile, embedded length 12m. Min.
• Qf = Qb + Qs
• Qb = fb x Ab
• fb = qc = 18000 kPa But limit of fb =11000 kPa
• Qb = fb x /4 B2 = 11000 x (0.42)2 x /4 = 1381.6 kN.
• Now Qs = Qs1 +Qs2 +Qs3.
0-10m 10-10.5m + > 10.5.\ fs1 = 0-10m = qc av /200 = 4000/200 =20 kPa.
• fs2 = 10 – 10.5 = qc av /200 = 13000/200 =65 kPa.
• fs3 = 10.5 – 12 = qc av /200 = 18000/200 = 90 kPa. (< 100 kPa)
• Qs = B [(10x20) + (0.5x65) + (1.5x90)]
D1 x fs1 D2 x fs2 D3 x fs3
= x 0.4 ( 200 + 32.5 + 135) = 461.81 kN.Qf = Qb + Qs = 1381.6 + 461.81 = 1 843.41
fs3 x B x D = 407
D = 407/90 x x 0.4 = 3.6m. 12 + 3.6 = 15.6 mQa = Qf /F.S. 1843.41/2.5 =737.36
Qf = Qa x F.S = 900 x 2.5 = 2250.
Receiving Load = 2250 – 1843 = 407 kN
Problem # 04
• A bored concrete pile 30 cm in dia. And 6.5m long, passes through stiff fissured clay, subjected to seasonal shrinkage and swelling upto a depth of 1.5m. The average undrained strength of clay varies linearly from 50 kPa at 1.5m to 186 kPa at 10m. Find the ultimate load capacity. Assume = 0.3.
Solution
• 1.5m top is ignored as the shrinkage may cause all adhesion to be lost.
• Cu at 1.5m depth = 50 kPa.
• Now cu at base = 50 + 186- 50/8.5 x 5 = 130 kPa
• Average cu = 50 + 130 /2 = 90 kPa.
• Qf = fb x Ab + fs As
• 1170 x /4 (0.3)2 + 27 x x 0.3 x 5• =82.7 + 127.27 = 210 kN.
Problem # 05(uplift Resistance)
• Find the uplift resistance and the safe uplift resistance (F.S = 2.5) of the under reamed pile installed in clay with the following data. (if the top 2m clay is active and subjected to swelling)
• Dia of shaft = 40 cm, dia. of bulb at base = 100cm.
• Length of shaft above bulb = 5m cu av along shaft = 115 kPa. Cu at base = 150 kPa and adhesion factor = 0.4
Solution
• Projected area of bulb = /4 (Bb – B2)= 0.659 m2 .• Neglecting top 2m of activeness• As = B x 3 = 3.77 m2
• Qup = 0.659 fb + 3.77 fs [ fb =Nc x cu =9x150=135
fs = cu = 0.4x 115 = 46] = 0.659x 1350 + 3.77 x 46 = 1063 kN Safe uplift resistance = 1063/2.5 = 425 kN
Problem # 06
• Find the penetration depth for a 35cm square R.C pile driven through sea bed for a jetty structure to carry a maximum compressive load of 500 kN and a net uplift load of 300 kN. The soil below sea bed consists of a 10m thick layer of saturated medium dense sand overlying dense sand and gravel. The average corrected SPT blows in the top 10m sand are 12 and on bottom sand gravel layer 40. No erosion is expected. The minimum safety factor should be 2.5 on the uplift load and 4 on the compressive load.
Solution• Nav for top10m = 12 (sandy layer)• N in sand –gravel = 40• Total ultimate uplift resistance required = 2.5x 300 = 750 kN• Now fs (medium dense sand)= 2 Nav = 2x12=24 kPa.
• Qs (uplift ) in top 10m = (4x0.35x10)24 = fs x As =336 kN.• Remaiing uplift resistance = 750 – 336 = 44 kN.• Friction resistance per meter length in sand gravel = fs xAs (one meter)
• fs (dense gravel) = 2 Nav = 2x 40 = 80 kPa.
Friction resistance /meter length = 80 x 4 x 0.35x1 =112 kN/m.Further penetration required in dense gravel to resist the uplift of 414 kN.
= 414/112 = 3.7mTotal Penetration = 10 + 3.7 = 13.7m for uplift.
Check for compressive load.Qf =Qb + Qs.
Qb = fb x Ab.
fb (dense gravel) = 40 N Lp /B ≤ 400 N. ≤400x40 ≤ 16000 kPa.
=40x4x 3.7/0.35= 16914.3 ≤ 16000 kPa.But maximum value of fb which could be adopted = 11000 kPa.
fb = 11000.
Now Qb = 11000 x (0.35)2 = 1347.5 kN.
Qs is same for compression as for uplift.\ Qf = 1347 + 750 = 2097 kN.\ F = Qf /Qa = 2097/500 = 4.2 > 4 safe.
this indicates that the required penetration is governed by uplift resistance. Penetration depth = 13.7 m below sea bed level
Problem # 07(Pile load test)
• The following data refers to a cyclic pile load test carried out on a 300mm dia. pile 10m long.
• Plot the load settlement curves (total and net) and estimate the allowable load by different methods/criterians.
Load on pile top (kN) 150 200 250 300 400 500 600Total settlement on pile top (mm)
1.45 2.25 2.75 3.6 5.75 10.75
30.00
Net settlement on pile top (mm)
0.40 0.65 0.80 1.0 1.70 5.25 22.80
Solution• Plot the load vs settlement ( Arithmatic graph)• Plot the load vs Net settlement(Arth. graph)• (a) Two third of the load causing 12 mm settlement, that is• Qa = 2/3 x 500 = 333.33 kN• (b) 50% of the load causing• Total settlement equal to 10%• Of the pile dia. i.e settlement of• 30mm (i.e 600 kN)• Qa = 1/2 x 600 = 300 kN.• (c) Net settlement 6mm 2/3 rd of that• 2/3 x 550 = 1100/3 = 366.66 kN• (d) Falling to striaght line Qu 600 kN, use F.S =2.• 600/2 = 300• Least of the above is 300 kN
Load
Sett
lem
ent
Problem # 08
• Two independent loading tests on 300mm dia. Short bored piles in clay for which = 0, yielded the following results.
• Embedded length of pile Added load at failure (kN)• 2.15 100• 2.75 110• Assuming the adhesion is effective over the whole of the
embedded length, estimate the mean cohesion of the soil and the shaft adhesion factor to be used in extrapolating the test results to larger piles. The densities of the soil and concrete are 1.92 Mg/m3 and 2.40 Mg/m3 respectively.
Solution:
• At point of failure v =0• s = 1.92 Mg/m3
• c = 2.4 Mg/m3. Qb + Qs = P + • (wt. of pile – wt. of excavated material)• Now P = 100 kN Lp = 2.15m.• Qb + Qs = c Ncp x Ab + c As = c Ncp x /4xd2
+ c x x d x Lp.
• = c x 9x /4 x 0.32 + c x x 0.3 x 2.15 = 0.636 c + 2.027 c • Ncp = 9 (Lp /d > 4)• P = 100 + wt. of pile – wt. of excavated material• = 100 + (2.4- 1.92) x 9.81 (/4 x 0.32 x 2.15)• = 100 + 0.715
Wt.
P
Qs
Qb
• v = 0• 100.715 = 0.636 c + 2.027 c -----------(i)• Similarly for 2nd test results v = 0• Qb + Qs =9x c x /4 (0.3)2
+ c x x 0.3 x2.75• = 0.636 c + 2.592 c• Load = 110 + (2.4 – 1.92) x 9.81 (/4 x 0.32 x 2.75)• = 110 + 0.915 = 110.915• 110.915 = 0.636 c + 2.592 c ---------------------(ii)• Solve equation simultaneously• c = 18.06 , c = 100 and = 0.18
Problem # 09
• A free standing, square group of 16 piles extends to a depth of 12 m in stiff clay which is underlain by rock at 24 m depth. The piles are 0.5 m in diameter and are spaced at 1.5 m centres. cT at base = 140 kPa, average (cT)av along shaft = 90 kPa, adhesion = 0.45, coefficient of volume decrease mv below base = 0.08 m2/MN, remoulded cT along shaft = 50 kPa. Assume group efficiency Eg = 0.65. Find the allowable load for the group with F = 2.5. Also estimate the settlement under the allowable load.
Solution:
• (a) Considering individual piles. fb = cT Ncp = 140 x 9 = 1260 kPa
fs = cT = 0.45 x 90 = 40.5 kPa
Qf = /4 B2 fb + B Lp fs
= /4 0.52 x 1260 + x 0.5 x 12 x 40.5 = 247.4 + 763.4 = 1010.8 kN Qg = Eg .n Qf = 0.65 x 16 x 1010.8 = 10512 kN
(b) Considering block failure. QB = Bo Lo fb + 2 Lp ( Bo +Lo) fB ; Bo = Lo = 5 m, Lp = 12 m
fb = cT Ncp = 140 x 9 =1260 kPa
fs = cT ( remolded) = 50 kPa
QB = 43500 kN > Qg (31500 + 12000)
Qa = 1/2.5 Qg = 10512/2.5 = 4205 kN
• For a settlement the load is assumed to act at an equivalent raft (5 m x 5 m) located at 12/3 = 4 m above the base. The compressible zone of 16 m thickness is divided into 4 layers, each 4 m thick. Pressure increase at the middle of each layer is calculated by assuming 2:1 spread of load Qs. The calculations are given in table. The total settlement is 48 mm.
Layer Mid-depth (m)
Area (m2 )
(kPa) mv H (mm)
1 2 49 85.80 27.45
2 6 121 34.75 11.12
3 10 225 18.68 5.97
4 14 361 11.65 3.73
48.28
Problem # 10
• A 40-ft-long precast pile is fully embedded in sand. The cross section of pile measures 12 in x 12 in. The allowable working load for the pile is 80 kip and 54 kip is contributed by skin friction. Determine the elastic settlement of the pile. Ep = 3 x 106 lb/in2 , Es = 4500 lb/in2 , and s = 0.3.
Solution:
2
22
31
2
2326p
1
/18.0144
26
,.82.0,27.3
)1(
.065.0)103)(144(
)1240()54)(6.0(26
.1441212
26,54,/103/103E 0.6, Let
inkipA
AlsoIFigureFrom
IE
Dqs
ins
TheninxA
kipQkipQinkipxinlbx
EA
LQQs
p
wpwp
wp
wpss
wp
p
wpws
pp
wswp
.71.0287.0358.0065.0
.287.021.4)3.01(
1000450012
40124
54
21.40.1
4035.0235.02
)1(
.38.082.03.01
10004500
1218.0
23
23
22
ins
issettlementtotaltheHence
ins
SoD
LI
IE
D
pL
Qs
ins
So
ws
wsss
ws
Problem # 11
Refer to Figure 8.47 which shows the plan of a pile group. Each pile has a square cross section measuring 12 in x 12 in. the center-to-center spacing of the piles is 30 in.Determine the group efficiency of the piles by using:a. Eq. (8.112)b. Eq. (8.114)
30 in.
12in
Fig. 8.47
Solution:
• Part a: Using Eq. (8.112)•
%4.60604.0
3418
48302342
.,484,12,3,4
422
21
21
21
inDpandinDnnFor
npn
Ddnn
• Part b: Using Eq. (8.114)
%.7.65657.08.21
4390
42331
8.2130
12tantan
tan90
111
11
1
21
1221
o
o
So
d
D
d
D
nn
nnnn
Problem #13
• Refer to Figure 8.41a. For this group pile, n1=4,n2= 3, D = 305 mm, d = 1220 mm, and L= 15 m. The piles are square in cross section and are embedded in a homogenous clay with cu = 70 kN/m2. Use FS = 4 and determine the allowable load-bearing capacity of the group pile. Assume = 0.63
Solution:
• From Eq. (8.116),
kN
Q
So
mkNcforFigureFrom
mp
mA
LpccAnnQ
u
u
p
upupu
1038703.80759.5812
157022.163.070093.0934
.63.0,/7019.8
22.1305.04
093.0305.0305.0
9
2
2
2
)(21
• Again from Eq. (8.117), the ultimate block capacity is Lg Bg cu(p) Nc*+2(Lg +Bg) cu L, So
• Lg = (n1 – 1)d +2(D/2) = (4-1)(1.22)+ 0.305=3.965 m
• Bg = (n2-1)d + 2(D/2) = (3-1)(1.22)+ 0.305= 2.745 m
• L/Bg = 15/2.745= 5.46
• Lg /Bg = 3.965/2.745 = 1.44
• From Figure 7.16, Nc* 8.6. Thus • Block capacity = (3.965)(2.745)(70)(8.6) + 2(3.965 + 2.745)
(70)(15) = 6552 + 14091 = 20643 kN• So• Qg(u) 10,387 kN < 20,643 kN
• Qg(all) = Qg(u) /FS = 10,387/4 2597 kN.
Problem # 14
• A group pile in clay is shown in Fig. Determine the consolidation settlement of the pile groups. All clays are normally consolidated.
6 ft
48 ft
3 ft
27 ft
21 ft
12 ft
6 ft
2v:1H2v:1H
z
45 ft30 ft
Water table
Qg = 500 kip
Clay
sat = 115 lb/ft3
eo = 0.82 Cc = 0.3
sat = 120lb/ft3
eo = 0.7 Cc = 0.2sat = 122 lb/ft3
eo = 0.75 Cc = 0.25
Clay
Clay
sand
= 105 lb/ft3
Rock
Po(1),
p(1)
Po(2),
p(2)
Po(3),
p(3)
Pile group: Lg = 9ft; Bg = 6ft
Solution:• The stress distribution pattern is shown in
Figure 8.49. Hence•
.45.87.0
2603
15542603log
82.01
213.0
/26034.621152
21271056
log1
/265366369
1000500
/421276279
1000500
/1554
221
6221
9
1000500
1
2)1(
)1(
)1()1(
)1(
1)1(1
2)3(
2)2(
2
11)1(
infts
ftlbp
p
pp
e
HCs
ftlbp
ftlbp
ftlbzBzL
Qp
o
o
o
o
c
gg
g
.58.929.084.045.8,
29.0024.04025
2654025log
75.01
625.0
/40254.621223
4.62120124.62115481056
84.03500
4213500log
7.01
122.0
/35004.6212064.6211521271056
log1
3
2
)3(
2
2)2(
)2(
)2()2(
)2(
2)2(2
inssettlementTotal
infts
ftlb
p
ins
ftlbp
p
pp
e
HCs
g
o
o
o
o
o
c
Problem # 15 • It is proposed to carry the load from a column on 350 mm
diameter bored piles. The total load to be carried is 2000 kN and the soil consists of a deep deposit of clay having the following properties:
• If the piles are • about 9 m long, • Estimate the • Number reqired • And suggest how • they should be• arranged
Depth (m)
Undrained shear strength (kN/m2)
0 100
3 110
6 125
9 125
12 135
Solution:• Consider the ultimate load carried on pile:• Qf = Qb + Qs
• Taking average cu on shaft of pile as = 115 kN/m2 and an adhesion factor of 0.45 for a bored pile:
• Qf = 125 x 9 x (/4 x 0.352) + 115 x 0.45 x ( x0.35 x 9)• = 108 + 512 = 620 kN• Using a factor of safety of 3: Qa = 620/3 = 207 kN• No of piles required to carry 2000 kN = 2000/207 = 9.6• Say 9 piles which reduces the factor of safety slightly.•
• Bored piles should be spaced at about 3 times their diameter and a suggested arrangement is shown on Fig.
• The action of the group• Must be checked for
stability.Consider a pier 2.35 m square:Qfg = 125 x 9 x 2.352 +115 x 0.45 x (4 x 2.35 x 9)
= 6212 + 4378 = 10590 kN
1 m
2.35 m1 m
top related