BabyLabs24-october-2018

SmallOnleyLabyrinths/Transmission LinesfortheFostexFF85wk/FF105wk/FE103 SOL,MarkAudioAlpair5.2,Alpair6.2p/Alpair6.2m,CHN-70,Pluvia7,andAuraNS3-193

Intendedfordesktopusebutoftenusesassmallstandmounts.

Freefornon-commercial use.

*©2010-2018WodenDesignFreefornon-commercialuse,commerciallicencingavailable

Notes 1: Baby Lab Examples23-april-2018

*© 2010-2018 Woden DesignFree for non-commercial use, commercial licencing available

Falcon | Jeff Drouin, Tulsa, Ok Shrike | Jeff Drouin, Tulsa, Ok Shrike | toobhead

Lance | nemonis

Stinger | planet10-hifi, Victoria, BC Falcon | planet10-hifi, Victoria, BC

Bloodhound Prototypes | Chris Bobiak, Victoria, BCRed Eye | Mike Jennens, Bismarck, ND / Jerms, Bucks, UK

Notes: Baby Labs23-april-2018

*© 2010-2018 Woden DesignFree for non-commercial use, commercial licencing available

Example Falcon Build

The LanceFF85wk Labyrinth TL 1v02Plan 1/2” | 14-december-2014designed by Scott Lindgren | drawn by dld© 2010-14 Woden DesignFree for non-commercial use

Notes:0/ drawn using 1/2” (12.7mm) material1/ damp top & back of 1st manifold, & one side down to just below the driver. Bottom of 1st & 2nd manifold, top of 2nd & 3rd manifold & adjust from there if needed with 1/2” ultratouch felt or equivalent2/ original design specification is imperial, minor adjustments formetric are fine

273.1[10 3/4]

203.3[8]

247.7[9 3/4]

177.9[7]

127[5]

101.6[4]

76.3[3]

50.8[2]

25.4[1]

50.8[2]

25.4[1]

25.4[1]

82.6[3 1/4]

3

The LanceFF85wk Labyrinth TL 1v02Damping | 19-january-2015designed by Scott Lindgren | drawn by dld© 2010-15 Woden DesignFree for non-commercial use

Notes:0/ damp top (1) & back (4) of 1st manifold, & one side (5) down to just below the driver. Bottom of 1st & 2nd manifold (2), top of 2nd & 3rd manifold & adjust from there if needed with 1/2” ultratouch felt or equivalent

4

5

2

112

3 3

4 5

5

1

76.3[3]

89[3 1/2]

140[5 1/2]

165[6 1/2]

470.3[18 17/32]

65[2 9/16]

101.6[4]

110[4 11/32]

FalconFF105wk Labyrinth TL 1v0Plan 1/2" | 23-april-2018designed by Scott Lindgren | drawn by dld© 2010-18 Woden DesignFree for non-commercial use

Notes:0/ drawn using 1/2" (12.7mm) material1/ damp top & back of 1st manifold, & one side down to just below the driver. Bottom of 1st & 2nd manifold, top of 2nd & 3rd manifold & adjust from there if needed with 1/2" ultratouch felt or equivalent2/ original design specification is imperial, minor adjustments formetric are fine

279.4[11]

273.2[10 3/4]

254[10]

247.8[9 3/4]

152.4[6]

127[5]

127.1[5]

63.5[2 1/2]

25.4[1]

63.5[2 1/2]

31.8[1 1/4]

31.8[1 1/4]

63.5[2 1/2]

4 53

FalconFF105wk Labyrinth TL 1v02Damping | 23-april-2018designed by Scott Lindgren | drawn by dld© 2010-18 Woden DesignFree for non-commercial use

Notes:0/ damp top (1) & back (4) of 1st manifold, & one side (5) down to just below the driver. Bottom of 1st & 2nd manifold (2), top of 2nd & 3rd manifold & adjust from there if needed with 1/2" ultratouch felt or equivalent

140[5 1/2]

179[7 1/32]

646[25 13/32]

3

3

5

1

4

2 1

5

3

2

109[4 9/32]

108[4 1/4]

127[5] 1

110[4 11/32]

ShrikeFE103 Sol Labyrinth TL 0v82Plan 1/2" | 24-april-2018designed by Scott Lindgren | drawn by dld© 2010-18 Woden DesignFree for non-commercial use

Notes:0/ drawn using 1/2" (12.7mm) material1/ damp top & back of 1st manifold, & one side down to just below the driver. Bottom of 1st & 2nd manifold, top of 2nd & 3rd manifold & adjust from there if needed with 1/2" ultratouch felt or equivalent2/ original design specification is imperial, minor adjustments formetric are fine

304.8[12]

304.8[12]

279.4[11]

279.4[11]

158.8[6 1/4]

133.4[5 1/4]

127.1[5]

85.7[3 3/8]

41.2[1 5/8]

108[4 1/4]

57.2[2 1/4]

41.3[1 5/8]

69.9[2 3/4]

BloodhoundAlpair 5.2 Labyrinth TL 0v99Plan 1/2” | 08-october-2015designed by Scott Lindgren | drawn by dld© 2010-15 Woden DesignFree for non-commercial use

Notes:0/ drawn using 1/2” (12.7mm) material1/ damp top & back of 1st manifold, & one side down to just below the driver. Bottom of 1st & 2nd manifold, top of 2nd & 3rd manifold & adjust from there if needed with 1/2” ultratouch felt or equivalent2/ original design specification is imperial, minor adjustments formetric are fine

279.4[11]

197[7 3/4]

254[10]

171.6[6 3/4]

139.7[5 1/2]

114.3[4 1/2]

76.3[3]

50.8[2]

19.1[3/4]

50.8[2]

19.1[3/4]

19.1[3/4]

69.9[2 3/4]

The StingerAlpair 6.2p/m Labyrinth TL 1v0Plan 1/2” | 14-december-2014designed by Scott Lindgren | drawn by dld© 2010-2014 Woden DesignFree for non-commercial use

Notes:0/ drawn using 1/2” (12.7mm) material. Due to thick bezel, 15mm or 5/8” baffle is suggested.1/ Damping: all faces 1st manifold leaving adequate breathing room for driver on front baffle. Top and bottom of 2nd manifold, + 2 non-opposing faces. Bottom of 3rd manifold + 2 non opposing faces for ~5in. Final few inches un-damped to preserve most of fundamental.2/ original design specification is imperial, minor adjustments formetric are fine3/ relieve the back of the driver cutout to ensure good breathing for the back of the cone.

279.4[11]

228.7[9]

254[10]

203.3[8]

165.1[6 1/2]

139.7[5 1/2]

101.7[4]

50.8[2]

25.4[1]

50.8[2]

25.4[1]

25.4[1]

63.5[2 1/2]

SkyflashCHN-70LabyrinthTL0v9Plan1/2”|24-october-2018designedbyScottLindgren|drawnbydld©2010-18WodenDesignFreefornon-commercialuse

Notes:0/drawnusing1/2”(12.7mm)material1/damptop&backof1stmanifold,&onesidedowntojustbelowthedriver.Bottomof1st&2ndmanifold,topof2nd&3rdmanifold&adjustfromthereifneededwith1/2”ultratouchfeltorequivalent2/originaldesignspecificationisimperial,minoradjustmentsformetricarefine

304.8[12]

273.2[103/4]

279.4[11]

247.8[93/4]

165.1[61/2]

139.7[51/2]

127.1[5]

63.5[21/2]

31.8[11/4]

63.5[21/2]

31.8[11/4]

31.8[11/4]

92.1[35/8]

StormShadowMarkAudioPluvia7LabyrinthTL0v81Plan1/2”|24-october-2018designedbyScottLindgren|drawnbydld©2010-18WodenDesignFreefornon-commercialuse

Notes:0/drawnusing1/2”(12.7mm)material1/damptop&backof1stmanifold,&onesidedowntojustbelowthedriver.Bottomof1st&2ndmanifold,topof2nd&3rdmanifold&adjustfromthereifneededwith1/2”ultratouchfeltorequivalent2/originaldesignspecificationisimperial,minoradjustmentsformetricarefine

323.9[123/4]

273.2[103/4]

298.5[113/4]

247.8[93/4]

158.8[61/4]

133.4[51/4]

127.1[5]

63.5[21/2]

31.8[11/4]

63.5[21/2]

31.8[11/4]

31.8[11/4]

101.8[4]

RedeyeAura NS3-193-8A Labyrinth TL 1v02Plan 1/2” | 14-december-2014designed by Scott Lindgren | drawn by dld© 2010-14 Woden DesignFree for non-commercial use

Notes:0/ drawn using 1/2” (12.7mm) material1/ damp top & back of 1st manifold, & one side down to just below the driver. Bottom of 1st & 2nd manifold, top of 2nd & 3rd manifold & adjust from there if needed with 1/2” ultratouch felt or equivalent2/ original design specification is imperial, minor adjustments formetric are fine

304.8[12]

228.6[9]

279.4[11]

203.3[8]

127[5]

101.6[4]

101.7[4]

50.8[2]

25.4[1]

50.8[2]

25.4[1]

25.4[1]

88.9[3 1/2]

82[3 7/32]

71[2 25/32]

65[2 9/16]

45[1 25/32]

Fostex FF85wkDimensions 0v9

16-october-2016 | drawn by D Dlugos© 2009-2016 planet_10 enterprises limited

3.4[1/8]

107[4 7/32]

92[3 5/8]

85[3 11/32]

51[2]

Fostex FF105wkDimensions 0v91

19-april-2018 | drawn by D Dlugos© 2009-2018 planet_10 enterprises limited

for licenced use only

2.5[3/32]

Ø115[Ø4 17/32]

Fostex FE103 SolDimensions 0v9

24-april-2018 | designed & drawn by D Dlugos© 2009-2016 planet_10 enterprises limited

for licenced use only

107[4 7/32]

92[3 5/8]

80[3 5/32]

47[1 27/32]

2.5[3/32] 5x7mmØ114

[Ø4 1/2]

100[3 15/16]

6[1/4]

39[1 17/32]

61[2 13/32]

78[3 1/16]

Alpair 5.xdriver dimensionsdrawn by dld | 19-march-2016

114[4 1/2]

6.1[0]

52[2]

93[3 1/2]

Alpair 6Alpair 6.2P | 6.2Mdriver dimensionsdrawn by dld | 14-nov-2017

Alpair 6.2: orient with Mark Audio logo at the top

103[4]

allow ~1 mm for gasket

100[3 15/16]

122.3[4 13/16]

4.5[3/16]

58[2 9/32]

Pluvia Seven / CHS-70

driver dimensionsdrawn by dld | 14-november-2017

70[2 3/4]

112[4 13/32]

allow ~1 mm for gasket

3[1/8]

Aura NS3Dimensions 0v9

24-april-2018 | drawn by D Dlugos© 2009-2018 planet_10 enterprises limited

for licenced use only

103.5[4 1/16]

36[1 13/32]

75.5[2 31/32]

54.9[2 5/32]

Ø93[Ø3 21/32]

Ø4.3[Ø5/32]