bottom structure in machinery spaces
TRANSCRIPT
-
8/9/2019 Bottom Structure in Machinery Spaces
1/11
A.A. B. Dinariyana; Soemartojo W.A. 19 March 2010
Jurusan Te ni Sistem Per apa anFakultasTeknologi Kelautan ITS SurabayaTA 2009 2010
The scantlings of floors are to be determined according to A.1.2.1 for the reatest s an measured in the en ine room.
Scantling of floor lates
2
-
8/9/2019 Bottom Structure in Machinery Spaces
2/11
3
4
-
8/9/2019 Bottom Structure in Machinery Spaces
3/11
w w y
engine foundation
should
be
as
large
as
possible
The depth of plate floors connected to web frames shall be similar to the depth of the longitudinal foundation girders.
w y , less than 0,5 h.
The web thickness is not to be less than:
5
The thickness of the longitudinal foundation girders is to be determined according to 3.2.1.The thickness of the longitudinal girders above theinner bottom is not to be less than:
P = sin le en ine out ut in kW
6
-
8/9/2019 Bottom Structure in Machinery Spaces
4/11
No centre girder need be fitted in way of longitudinal foundation irders. Intercostal dockin rofiles are to be fitted instead. The sectional area of the docking profiles is not to be less than :
Docking profiles are not required where a bar keel is fitted. Brackets connecting the plate floors to the bar ee are to e itte on eit er si e o t e oors.
7
Double Bottom General (Section 8, C.2.1)
g en ng o es n way o eng ne oun a on are o be kept as small as possible with due regard, however, to accessibilit .
Where necessary, the edges of lightening holes are to
panels are to be stiffened.
Local strengthenings are
to
be
provided
beside
the
following minimum requirements, according to the
.
8
-
8/9/2019 Bottom Structure in Machinery Spaces
5/11
Plate floors are to be fitted at every frame.The floor thickness is to be increased by:
Minimum 5 percent, maximum 15 percentP = single engine output in [kW]
The thickness of the late floors below web frames is to be increased in addition to the above provisions. In this case the thickness of the plate floors is not to be taken less than
9
the web thickness according to Section 9, A.6.2.1.
Double bottom Side girders/Longitudinal girders
The thickness of side girders under an engine foundation top plate inserted into the inner bottom
the inner bottom.
10
P = single engine output in [kW]
-
8/9/2019 Bottom Structure in Machinery Spaces
6/11
Side girders
Side girders with thickness of longitudinal
girders in full height of the double bottom.
Where two side girders are fitted on either ,
girder under the inner bottom for engines up .
11
Side girders
Side girders under foundation girders are to be extended into adjacent spaces and to be connec e o e o om s ruc ure.
room bulkheads shall be two or four frame spacing if practicable.
No center girder is required in way of the engine .
12
-
8/9/2019 Bottom Structure in Machinery Spaces
7/11
, plating required according to B.4.1. to be increased by 2 mm.
The stren thened late is to be extended be ond the en ine seating by three to five frame spacing.
13
General The following rules apply to low speed engines. Seating for medium and high speed
engines as well as for turbines will be specially considered.
The rigidity of the engine seating and the
to keep the deformations of the system due to the loads within the permissible limits.
In special cases, proof of deformations and .
14
-
8/9/2019 Bottom Structure in Machinery Spaces
8/11
at the seating shall be spaced no more than 3
the longitudinal foundation girder.
Where the distance of the foundation bolts
greater, proof of equivalence is to be .
15
Engine seating
bottom is not less than:
P = single engine output in [kW]
the engine, their thickness may be reduced by 4 mm.
16
-
8/9/2019 Bottom Structure in Machinery Spaces
9/11
Engine seating Top plate
The sizes of the top plate (width and thickness) shall be sufficient to attain efficient attachment
:Seating height and type of engine
.
The thickness of the to late shall approximately be equal to the diameter of the fitted in bolts.
17
Engine seating Top plate
than:
Where twin engines are fitted, a continuous top plate is to
propeller shaft.18
-
8/9/2019 Bottom Structure in Machinery Spaces
10/11
Engine seating Top plate
op p ates are pre era y to e connecte to longitudinal and transverse girder thicker than a roximate 1 mm b means of double bevel butt joint.
19
20
-
8/9/2019 Bottom Structure in Machinery Spaces
11/11
Ship Construction
Sketches
and
Notes , ,
1984Peraturan Biro Klasi ikasi Indonesia Volume II, Edition 2006
21