camd assembly

Bench Vice Assembly 1

In this project, you will create the Bench Vice assembly. Figures B through E shows the viewsand dimensions of the components of the Bench Vice assembly.

Bench Vice Assembly

Figure 2 Views and dimensions of the base

Figure 1 The Bench Vice assembly

CAMD_ProE_Assembly 1 MIT College of Engineering, Pune - 411038.

2 Student Project

Figure 4 Views and dimensions of various components of the Bench Vice assembly

Figure 3 Views and dimensions of the Vice Jaw


Bench Vice Assembly 3

Figures 5 Views and dimensions of various components of the Bench Vice assembly


Butterfly Valve Assembly 1

Create the components of the Butterfly Valve assembly and then assemble them, as shown inFigure 1. The dimensions of the components are shown in Figures 2 through 7. Assume themissing dimensions.

Butterfly Valve Assembly

Figure 1 The Butterfly Valve assembly

Figure 2 Dimensions of the BodyCAMD_ProE_Assembly 4 MIT College of Engineering, Pune - 411038.

2 Student Project

Figure 4 Dimensions of the RetainerFigure 3 Dimensions of the Shaft

Figure 6 Sectional front view of the ArmFigure 5 Top view of the Arm

Figure 7 Dimensions of the Plate, Nut, and Screw


V-Block Assembly 1

Figure 2 Views and dimensions of the V-Block body

Create all the components of the V-Block assembly and then assemble them, as shown inFigure 1. The dimensions of the components are shown in Figures 2 and 2.

V-Block Assembly

Figure 1 The V-Block assembly


2 Student Project

Figure 3 Views and dimensions of the U-Clamp and Fastener


Crosshead Assembly 1

Crosshead Assembly

Figure 2 The exploded state of Crosshead assembly

Figure 1 The Crosshead assembly

In this project, you will create all components of the Crosshead assembly and then assemblethem, as shown in Figure 1. Also you will create an exploded state, shown in Figure 2. Thedimensions of the components are shown in Figures 3 through 7.


2 Student Project

Figure 3 Front view and the right-side view of the Body

Figure 5 Dimensions of Piston RodFigure 4 Dimensions of Keep Plate

Figure 6 Dimensions of the Brasses and Bolt


Crosshead Assembly 3

Figure 7 Dimensions of Nut


Double Bearing Assembly 1

In this project, you will create the Double Bearing assembly shown in Figure 1. The explodedstate of the assembly is shown in Figure 2 and the dimensions of the components of theDouble Bearing assembly are shown in Figures 3 through 7.

Double Bearing Assembly

Figure 4 Top view of the CapFigure 3 Top view of the Base

Figure 2 The exploded view of the DoubleBearing assembly

Figure 1 The completed Double Bearingassembly

Figure 6 Front view of the CapFigure 5 Front view of the BaseCAMD_ProE_Assembly 11 MIT College of Engineering, Pune - 411038.

2 Student Project

Figure 7 Dimensions and drawing views of the Bushing and the Bolt


Fixture Assembly 1

Create all the components of the Fixture assembly and then assemble them, as shown inFigure 1. The details of the components of the Fixture assembly are shown inFigures 2 through 5.

Fixture Assembly

Figure 1 The Fixture assembly

Figure 2 Dimensions of the End Plate


2 Student Project

Figure 3 Dimensions of the Disk

Figure 4 Dimensions of the Support Pin and the Bolt


Fixture Assembly 3

Figure 5 Dimensions of the Spacer, Center Pin, and the Nut


Plummer Block Assembly 1

Figure 2 Views and dimensions of the Casting

In this project, you will create the components of the Plummer Block assembly, as shown inFigure 1 and then assemble them. The dimensions of the components are given in Figures 2through 4.

Plummer Block Assembly

Figure 1 The Plummer Block assembly


2 Student Project

Figure 3 Views and dimensions of the Cap

Figure 4 Views and dimensions of Brasses, Nut, Lock Nut, and Bolt


Press Tool Assembly 1

In this project, you will create the Press Tool assembly shown in Figure 1. The exploded stateof the assembly is shown in Figure 2 and the dimensions of the components of the Press Toolassembly are shown in Figures 2 through 5.

Press Tool Assembly

Figure 1 The completed Press Tool assembly after assembling theTop Plate with the assembly

Figure 2 The exploded view of the Press Tool as-sembly

Figure 3 Figure showing the Bottom Plate


2 Student Project

Figure 5 Dimensions and views of the Guide Pillarand Guide Bush

Figure 4 Dimensions and views of the TopPlate


Pulley Support Assembly 1

Figure 2 Exploded view of the Pulley Support assembly

Create the components of the Pulley Support assembly and then assemble them, as shown inFigure 1. After creating the assembly, create its exploded view, as shown in Figure 2. Thedimensions of the components are given in Figures 4 through 8.

Pulley Support Assembly

Figure 1 The Pulley Support assembly


2 Student Project

Figure 8 Dimensions of the Washer, Cap Screw, Turn Screw, and Nut

Figure 5 Dimensions of the BushingFigure 4 Dimensions of the Pulley

Figure 7 Sectioned front view of theFigure 6 Left-side view of the Bracket


Pulley Support Assembly 3

Figure 3 Parts list for the Pulley Support assembly


Shock Assembly 1

Shock Assembly

Figure 1 The Shock assembly

In this project, you will create all components of the Shock assembly and then assemblethem, as shown in Figure 1. Also create an exploded state of the assembly, as shown inFigure 2. The dimensions of the components are shown in Figures 3 through 10.

Figure 2 The exploded state of the Shock Assembly


2 Student Project

Figure 4 Dimensions for PivotFigure 3 Dimensions for Bracket

Figure 5 Dimensions for U-Support


Shock Assembly 3

Figure 9 Dimensions for Hexagonal boltFigure 8 Dimensions for Washer

Figure 6 Dimensions for Bushing Figure 7 Dimensions for Self-locking nut

Figure 10 Dimensions for Castle nut


Wheel Support Assembly 1

Create all the components of the Wheel Support assembly and then assemble them, as shownin Figure 1. The dimensions of the components are shown in Figures 2 through 6.

Wheel Support Assembly

Figure 1 The Wheel Support assembly

Figure 9-3 Dimensions of the SupportFigure 2 Dimensions of the Base

Figure 5 Sectioned side view of the WheelFigure 4 Front view of the Wheel


2 Student Project

Figure 6 Dimensions of the Shoulder Screw, Bolt, Nut, Bushing,and Washer


Pipe Vice Assembly 1

In this Project, you will create all components of the Pipe Vice assembly, as shown inFigure 1, and then assemble them. The dimensions of the components are given inFigures 2 and 3.

Figure 1 The Pipe Vice assembly

Pipe Vice Assembly

Figure 2 Views and dimensions of the Base


2 Student Project

Figure 3 Views and dimensions of the Screw, Handle, Movable Jaw, and Handle Screw


Shaper Tool Head Assembly 1

Create the Shaper Tool Head assembly, as shown in Figure 1. After creating the assembly, createits exploded view, as shown in Figure 2. The dimensions of the components are given inFigures 3 through 7.

Shaper Tool Head Assembly

Figure 1 The Shaper Tool Head assembly

Figure 2 The exploded view of the Shaper ToolHead assembly


2 Student Project

Figure 3 Views and dimensions of the Swivel Plate



Figure 4 Views and dimensions of the Back Plate


4 Student Project

Figure 5 Views and dimensions of the Vertical Slide



Figure 6 Views and dimensions of various components


Stock Bracket Assembly 1

Figure 2 Top and front views of the Stock Support Base

In this project, you will create the Stock Bracket assembly shown in Figure 1. The details ofthe components of the Stock Bracket assembly are shown in Figures 2 through 8.

Stock Bracket Assembly

Figure 1 The Stock Bracket assembly


2 Student Project

Figure 4 Top and front views of the Adjusting ScrewNut

Figure 3 Front and right-side views of the StockSupport Roller

Figure 6 Views of the Adjusting Nut Handle andAdjusting Screw Guide

Figure 5 Front and right-side views of the Support Roller Bracket


Stock Bracket Assembly 3

Figure 8 Top and front views of the ThrustBearing

Figure 7 Views of the Support Adjusting Screw


Motor Blower Assembly 1

In this project, you will create the Motor Blower assembly shown in Figure 1. The explodedview of the assembly is shown in Figure 2. The details of the components of the Motor Blowerassembly are shown in Figures 3 through 8.

Figure 1 Motor Blower assembly

Figure 2 Exploded view of the Motor Blower assembly

Motor Blower Assembly


2 Student Project

Figure 3 Dimensions of the Upper Housing

Figure 4 Dimensions of the Lower Housing


Motor Blower Assembly 3

Figure 5 Dimensions of the Blower

Figure 6 Dimensions of the Motor


4 Student Project

Figure 8 Dimensions of the Shaft

Figure 7 Dimensions of the Cover


Radial Engine Assembly 1

In this project, you will create the Radial Engine assembly shown in Figures 1 and 2. TheRadial Engine assembly will be created in two parts, one will be the subassembly and theother will be the main assembly. The dimensions of the components of the Radial Engineassembly are shown in Figures 3 through 6.

Radial Engine Assembly

Figure 1 The Radial Engine assembly Figure 2 The exploded view of the assembly

Figure 3 Views and dimensions of the Piston


2 Student Project

Figure 5 Views and dimensions of the Master Rod

Figure 4 Views and dimensions of the Articulated Rod


Radial Engine Assembly 3

Figure 6 Views and dimensions of the Rod Bush Upper, Rod Bush Lower, Piston Pin Plug,Piston Pin, Piston Rings, and Master Rod Bearing


01 Bench Vice Assembly02 Butterfly Valve Assembly03 V-block Assembly04 Crosshead Assembly05 Double Bearing Assembly06 Fixture Assembly07 Plummer Block Assembly08 Press Tool Assembly09 Pulley Support Assembly10 Shock Assembly11 Wheel Support Assembly12 Pipe Vice Assembly13 Shaper Tool Head Assembly14 Stock Bracket Assembly15Motor blower Assembly16 Radial Engine Assembly

camd assembly

Documents

bench vice assembly

mit college of engineering

dimensions of nutcamd

viewsand dimensions

themissing dimensions

bench vice assemblyfigure

dimensions of piston

bench vice assemblycamd