1

Ver. 1.3 2006.05

Model Name Using Similar Mechanism NEW

CD Drive Mechanism Type MG-611MM-186//K

Optical Pick-up Name KSS1000E

SERVICE MANUAL E ModelChinese Model

CD player sectionSignal-to-noise ratio 90 dBFrequency response 10 20,000 HzWow and flutter Below measurable limitSignal format system PAL/NTSC

Tuner sectionFMTuning range FM tuning interval:

50 kHz/200 kHzswitchable87.5 108.0 MHz(at 50 kHz step)87.5 107.9 MHz(at 200 kHz step)

Aerial terminal External aerial connectorIntermediate frequency 10.7 MHz/450 kHzUsable sensitivity 9 dBfSelectivity 75 dB at 400 kHzSignal-to-noise ratio 67 dB (stereo),

69 dB (mono)Harmonic distortion at 1 kHz

0.5% (stereo),0.3% (mono)

Separation 35 dB at 1 kHzFrequency response 30 15,000 Hz

AMTuning range AM tuning interval:

9 kHz/10 kHz switchable531 1,602 kHz(at 9 kHz step)530 1,710 kHz(at 10 kHz step)

Aerial terminal External aerial connectorIntermediate frequency 10.7 MHz/450 kHzSensitivity 30 V

SPECIFICATIONS

Power amplifier sectionOutputs Speaker outputs

(sure seal connectors)Speaker impedance 4 8 ohmsMaximum power output 52 W 4 (at 4 ohms)

GeneralOutputs Audio output terminals (front, rear/sub switchable)

Video output terminalPower aerial relay control terminalPower amplifier control terminal

Inputs AUX IN terminalParking break control terminalAerial input terminal

Tone controls Low:10 dB at 60 Hz (XPLOD)Mid:10 dB at 1 kHz (XPLOD)High:10 dB at 10 kHz (XPLOD)

Power requirements 12 V DC car battery(negative earth)

Dimensions Approx. 178 50 179 mm (w/h/d)Mounting dimensions Approx. 182 53 161 mm (w/h/d)Mass Approx. 1.2 kgSupplied accessories Parts for installation and connections (1 set)

Front panel case (1)Card remote commander RM-X158

Design and specifications are subject to change withoutnotice.

The tuner and CD sections have no adjustments.

Sony CorporationeVehicle Division

Published by Sony Techno Create Corporation

9-879-406-042006E04-1

2006.05

FM/AM MULTI MEDIA PLAYER

CDX-V3800

2

CDX-V3800

CAUTIONUse of controls or adjustments or performance of proceduresother than those specified herein may result in hazardousradiation exposure.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINEWITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS LIST ARE CRITICAL TO SAFE OPERATION.REPLACE THESE COMPONENTS WITH SONY PARTS WHOSEPART NUMBERS APPEAR AS SHOWN IN THIS MANUAL ORIN SUPPLEMENTS PUBLISHED BY SONY.

NOTES ON HANDLING THE OPTICAL PICK-UP BLOCKOR BASE UNITThe laser diode in the optical pick-up block may suffer electrostaticbreakdown because of the potential difference generated by thecharged electrostatic load, etc. on clothing and the human body.During repair, pay attention to electrostatic breakdown and also usethe procedure in the printed matter which is included in the repairparts.The flexible board is easily damaged and should be handled withcare.

NOTES ON LASER DIODE EMISSION CHECKThe laser beam on this model is concentrated so as to be focused onthe disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission, ob-serve from more than 30 cm away from the objective lens.

Notes on Chip Component Replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be dam-

aged by heat.

SERVICE NOTES

If the optical pick-up block is defective, please replace the wholeoptical pick-up block.Never turn the semi-fixed resistor located at the side of opticalpick-up block.

TEST DISCSThis set can playback CD-R and CD-ROM discs. The followingtest discs should be used to check the capability:

CD-R test disc TCD-R082LMT (Part No. J-2502-063-1)CD-RW test disc TCD-W082L (Part No. J-2502-063-2)

optical pick-up

semi-fixed resistor

This label is located on the bottom of the chassis.

Ver. 1.2

E model

Chinese model

3

CDX-V3800

Notes on CD-Rs (recordable CDs)/CD-RWs (rewritableCDs)This unit can play the following discs:

Type of discs Label on the disc

Audio CD

MP3 files

Some CD-Rs/CD-RWs (depending on the equipment used forits recording or the condition of the disc) may not play on thisunit.

You cannot play a CD-R/CD-RW that is not finalized. You can play MP3 files recorded on CD-ROMs, CD-Rs, and

CD-RWs. A CD-R/CD-RW to which a session can be added can be played.

A process necessary for a recorded CD-R/CD-RW disc to beplayed on the audio CD player.

Notes on Video CDsThis unit can play the following discs:

Type of discs Label on the disc

Video CD

VCD

A compact disc that contains moving pictures.The picture data uses the MPEG 1 format (Video CD), worldwidestandards of digital compression technology.Video CDs also contain compact audio data.Sounds outside the range of human hearing are compressed whilethe sounds we can hear are not compressed.

z UNLEADED SOLDERBoards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed withthe lead free mark due to their particular size.)

: LEAD FREE MARKUnleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40C higher than

ordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint for a slightly longer time.Soldering irons using a temperature regulator should be set toabout 350C.Caution: The printed pattern (copper foil) may peel away if theheated tip is applied for too long, so be careful!

Strong viscosityUnleaded solder is more viscous (sticky, less prone to flow)than ordinary solder so use caution not to let solder bridgesoccur such as on IC pins, etc.

Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder mayalso be added to ordinary solder.

4

CDX-V3800

TABLE OF CONTENTS

1. GENERALLocation of Controls ................................................................ 5Connections ............................................................................. 5

2. DISASSEMBLY2-1. Sub Panel (1) Assy .............................................................. 82-2. CD Mechanism Block ......................................................... 82-3. Main Board ......................................................................... 92-4. Chassis (T) Sub Assy .......................................................... 92-5. Roller Arm Assy ................................................................ 102-6. Chassis (OP) Assy ............................................................. 102-7. Optical Pick-up ................................................................. 112-8. SL Motor Assy (M902) ..................................................... 112-9. LE Motor Assy (M903) ..................................................... 122-10. Servo Board ....................................................................... 12

3. DIAGRAMS3-1. Block Diagram CD Section ........................................... 133-2. Block Diagram Main Section ........................................ 143-3. Block Diagram Display Section .................................... 153-4. Circuit Boards Location .................................................... 153-5. Printed Wiring Boards CD Mechanism Section ............ 173-6. Schematic Diagram CD Mechanism Section (1/2) ....... 183-7. Schematic Diagram CD Mechanism Section (2/2) ....... 193-8. Printed Wiring Boards Main Section ............................ 203-9. Schematic Diagram Main Section (1/3) ........................ 213-10. Schematic Diagram Main Section (2/3) ........................ 223-11. Schematic Diagram Main Section (3/3) ........................ 233-12. Printed Wiring Board Display Section .......................... 243-13. Schematic Diagram Display Section ............................. 25

4. EXPLODED VIEWS4-1. Main Section ..................................................................... 324-2. Front Panel Section ........................................................... 334-3. CD Mechanism Section (1) ............................................... 344-4. CD Mechanism Section (2) ............................................... 354-5. CD Mechanism Section (3) ............................................... 364-6. CD Mechanism Section (4) ............................................... 37

5. ELECTRICAL PARTS LIST ......................................... 38

5

CDX-V3800SECTION 1GENERAL This section is extracted

from instruction manual.

CONNECTIONS

4

Location of controlsRefer to the pages listed for details.

a Volume +/ buttonb ATT (attenuate) button 17c DSPL (display mode change) button

11, 14d OPEN/EJECT shutter 11, 12e Display windowf EQ3 button 18g OFF (Stop/Power off) button*1 10, 12,

18h SEEK +/ button

Radio:To tune in stations automatically/find a station manually. CD/VCD:To skip tracks/fast-forward, reverse a track.

i (front panel release) button 10j SOURCE (Power on/Radio/CD/AUX)

buttonTo select the source.

k MODE buttonTo change the operation.

l SEL (select) buttonTo select items.

m RESET button (located on the front side of the unit, behind the front panel) 9

n Number buttons 17Radio: To store stations/receive stored stations.CD/VCD: (1): REP 15(2): SHUF 15(3): SLOW 13(4): AUDIO 14(5): OSD 19(6): PAUSE 12, 13

o Frequency select switch (located on the bottom of the unit) See Frequency select switch in the Installation/Connections manual.

p SENS/ALBUM button 12, 16q BTM/ALBUM + button 12, 15r SCRL (scroll) button 14s Receptor for the card remote

commander

*1 Warning when installing in a car without an ACC (accessory) position on the ignition switchAfter turning off the ignition, be sure to press and hold (OFF) on the unit until the display disappears.Otherwise, the display does not turn off and this causes battery drain.

EQ3

ATT OFF

SOURCE MODE SEL

SEEK

1 2 3 4 5 6 SENSSLOW ALBUM +AUDIO OSD PAUSEREP SHUF

CDX-V3800

BTM SCRL

DSPL

5

The corresponding buttons of the card remote commander control the same functions as those on this unit.

a OFF buttonb SOURCE buttonc PBC button 14d ENTER button 14e < (.)/, (>) buttonsf DSPL buttong VOL (+/) buttonh ATT buttoni SEL buttonj MODE buttonk O (return) button 14l M (+)/m () buttons 14m SCRL buttonn Number buttons

NoteIf the display disappears by pressing (OFF), it cannot be operated with the card remote commander unless (SOURCE) on the unit is pressed, or a disc is inserted to activate the unit first.

TipFor details on how to replace the battery, see Replacing the lithium battery on page 20.

Selecting an album with the card remote commanderAlbum can be skipped using M (+)/m () on the card remote commander.

* Available only when an MP3 file is played.

Skipping tracks continuouslyPress once < or , on the card remote commander, then press again within 2 seconds and hold.

Card remote commander RM-X158

OFF

DSPL

REP SHUF SLOW

PBC

SCRL

SOURCE SEL MODE

PAUSEOSDAUDIO

1 32

4 65

ATT

VOL+

+

ENTER

2

3

91

qd

4

5

6

8

7

qf

qa

qs

q;

To Press

Skip albums* Album selection

M or m [once for each album]To continuously skip albums, press and hold either button.

2A

B

AUDIO OUT REAR

AUDIO OUT FRONT

VIDEO OUT

6

CDX-V3800

7

CDX-V3800SECTION 2

DISASSEMBLY

Note : This set can be disassemble according to the following sequence.

2-1. SUB PANEL (1) ASSY(Page 8)

2-2. CD MECHANISM BLOCK(Page 8)

SET

2-3. MAIN BOARD(Page 9)

2-4. CHASSIS (T) SUB ASSY(Page 9)

2-5. ROLLER ARM ASSY(Page 10)

2-6. CHASSIS (OP) ASSY(Page 10)

2-8. SL MOTOR ASSY (M902)(Page 11)

2-10. SERVO BOARD(Page 12)

2-7. OPTICAL PICK-UP(Page 11)

2-9. LE MOTOR ASSY (M903)(Page 12)

8

CDX-V3800

2-2. CD MECHANISM BLOCK

Note : Follow the disassembly procedure in the numerical order given.

2-1. SUB PANEL (1) ASSY

2 two claws

3 two claws

4 sub panel (1) assy

1 two screws (+PTT 2.6 x 6)

8 bracket (CD)

6 CD mechanism block

SERVO board

4 CN751 (26core) 5 CN401 (2P)

3

1 screw (+PTT 2.6 x 6)

2 screw (+PTT 2.6 x 6)

7 two screws (+PTT 2.6 x 6)

9

CDX-V3800

2-4. CHASSIS (T) SUB ASSY

2-3. MAIN BOARD

5 SENSOR board

6 chassis (T) sub assy

4 claw

3 claw

1 two screws (+P 1.7 x 2.2)

2 two screws (+P 1.7 x 2.2)

1 three screws (+BTT )

3 MAIN board

4 insulating sheet

2 two screws (+PTT 2.6 x 8)

5 screw (+PTT 2.6 x 8)

6 connection (video out) cord

10

CDX-V3800

2-5. ROLLER ARM ASSY

2-6. CHASSIS (OP) ASSY

4 gear (RA1)

5 roller arm assy

1 spring (RAL)

2 spring (RAR)

3 washer (1.1-2.5)

4 washer

0 coil spring (damper)

9 two coil springs (damper)

qa chassis (OP) assy

5 gear (LE1)

1 CN500 (16P)

lever (D)

slider (R)

6

7

8

2 Remove the six solderings.

3 tension coil spring (KF60)

11

CDX-V3800

2-7. OPTICAL PICK-UP

2-8. SL MOTOR ASSY (M902)

1 screw (+P 1.4 x 1.8)

2 SL motor assy (M902)

1 tension coil spring (CHKG)

2 chucking arm sub assy

3 screw (+B 1.4 x 5)

4 rack (SL)

5 claw

6 main shaft

7 optical pick-up

12

CDX-V3800

2-9. LE MOTOR ASSY (M903)

2-10. SERVO BOARD

2 washer

4

qd

3 gear (LE1)

7 leaf spring (LE)

5

lever (D)

bracket (LEM-N)

slider (R)

6 screw (+P 1.7 x 2.2)

8 screw (+M 1.7 x 2.5)

qa screw (+M 1.7 x 2.5)qf two toothed lock screws

(+M 1.4 )

qs screw (+M 1.7 x 2.5)

9 bearing (LEB-N)

0 gear (LE) assy

qg LE motor assy (M903)

1 Remove the two solderings.

4 CN500 (16P)

6 claw

7 SERVO board

5 precision screw (+P 1.7 x 2.2)

2 Remove the eight solderings.

1 shield sheet

3 Remove the three solderings.

13 13

CDX-V3800

CDX-V3800

RF AMP,DIGITAL SERVO,

IC500

52EQ0

9FEO46TZCRFM48TEO

51 RFI

8 FEN

49 TEN

42 XI

43 XO

PD1

PD2

E

F

I-V A

MP

PD LD

DETECTOR

35DOUTA 96 CD DATA

36LRCK 97 CD LRCK

34WFCK 50 BATTLOW37DCK 98 CD BCLK

38EFLAG 102 CD XCK

31SUBSYQ 81 SUBSYQ30BUSY 80 BUSY

29RESETX 82 XRESET

28R/W 83 R/W

27DIN/OUT 84 DI/DO

26MCK 85 MCK

CLKIN

CLKIO

3

2

5

6

E

AC

BD

F

13 LD 12PD

24LON

(FOCUS)

(TRACKING)

2-AXIS DEVICE

OPTICALPICK-UP BLOCK

(KSS1000E)

Siganal Path: CD PLAY

LASER DIODE

M

M

M

17

18

14

13

12

11

10

9

VOL(+)

VOL(-)

FWD

REV

1

28

IN1() 3

OUT1

IN2()

OUT2

IN3()

OUT3

IN4()

OUT4

4

22 CLV OUT6

7

18 TDOUT

17 JUMP0

23

19 SDIN22

21 FD OUT26

25

16

15

VO4()

VO4(+)

VO3(+)

VO3(-)

VO1(+)

VO1(-)

VO2(+)

VO2(-)

M903(LOADING)

M901(SPINDLE)

M902(SLED)

FOCUS/TRACKING COIL DRIVE,SLED/SPINDLE/LOADING

MOTOR DRIVEIC600

CD-L MAIN SECTIONA

56VSYNC

36DQMOLDONUDQMWECASRASBACLK

14

9 15WE B10 16CAS B11 17RASO B112 19BAO

SI

127 35RAMCLK

55HSYNC

78AU LRCK79AU BCK76AU XCK103DEEMP

77AU DATA

55 CD SELFSW

92 CD INSW

93 CD LOAD

CD SO

CD ON

BU+3.3V U COM+3.3V

1990SO 91

SCK 93RESET B 99

SP 88MP 89

MUTE 113

16M SDROMIC200

16M SDROMIC300

VIDEO SIGNALPROCESSOR

IC400

DIGITAL SIGNAL PROCESSORIC100

DIGITALMODULATOR

IC700

CD SI18CD SCK20CD XRST98SP54MP90

SW2(SELF)

95 CD DSWSW1(DOWN)

S901(LIMIT)

SW3(DISC IN)

94 EJECT

69CLK27 OUT70PLA NTSC54V RST

2 DIN

1 LRCK3 BCKIN

14 SCKI

12 DEEMP

9LOUT

6ROUT R-CH

10MUTE

13FORMAT

32CVBS/Y

PD2

E

F

LD

MONOUT

FCS+

FCS

TRK+

TRK

PD1

AUTOMATICPOWER

CONTROLQ501

LASER ONCONTROLSWITCH

Q502 R-ch is omitted due to same as L-ch.

66

65X401

27MHz

X54116.934MHz

MUTED701

MAIN SECTIONB

15 CLK14 MODEB

28 VSYNC29 HSYNC

9 SLEEP

YC0I

YC7

P0I

P7

2725232122242628

ROMD0I

ROMD7

2932343840424139333544

434549

ROMA0I

ROMA18

2931333538304244

DQ0I

DQ7

452518814817

A0I

A18

ROMA0-ROMA18

ROMD0-ROMD7

RAMA0-RAMA10

RAMD0-RAMD15

17201612111110

DA0I

DA10

2124273220

A0I

A10

11612362126124

23568911123940424345

464849

DQ0I

DQ15

92 LIMIT

64I

57

17I

24

20 SD OUT

87

CN401(VIDEO OUT)

114

DD0I

DD15

SYSTEM CONTROLIC801 (1/3)

CD POWERCONTROLQ701,703

3-1. BLOCK DIAGRAM CD SECTION

(Page 14)

(Page 14)

SECTION 3DIAGRAMS

1414

CDX-V3800

CDX-V3800

3-2. BLOCK DIAGRAM MAIN SECTION

1 ANT 7 B2

ELECTRONIC VOLUMEIC401

PJ601(ANTENNA)

TUX601(TUNER UNIT)

POWER AMPIC100

SYSTEM CONTROLIC801 (2/3)

CNP901

6 B1

R-CH (FRONT)R-CH (REAR)

BATT

9 C28 C1

R-CH

43

10VCC11TU VDD15E2P VDD

13TU-SCL14TU-SDA

6S-METER7TU MUTE

16E2P SCL17E2P SDA

45 VSM

AU+8VTU+5VU COM+3.3V

15 TU ATT

25 EEP SCK24 EEP SIO

LR

CD-L

R-CH

1718

OUTS2OUTS1

R-CH

L

R

53

LF+LF-

97

RF+RF-

2927

SW1

R-CH

SW2

BATT

3037

REG1REG2

3133

REG3REG4

34REG5

TU+5V

BATT

2524

OUTF1OUTR1

29MUTE

2 SDA

AU+8VU-COM+3.3VSERVO+3.3VMECHA+6VDISP+B

4 SCL

SDASCL

16 ACGND22 STB25 DIAG

AU+8V

35 VP

15

7

10

12

11

16

19

2

4

3

56

3031

SCLSDA

SCLSDA

SCLSDA

SCLSDA

33IIC SCK34IIC SIO

6VOL ATT

1LINE ATT

5BEEP31STB56DIAG

53BU IN

67PAK BK

12 IN RR(FL) FL+FL-

RL+RL-

FR+FR-RR+RR-

AMP-REMANT-REM

ACC

PAK BK

23OUTF2

11 IN RF(RL)22OUTR2

MUTEQ405

MUTEQ407

REARAUDIO OUT

MUTE DRIVEQ400,401

58UNI SI59UNI SO

64ACC INACC CHECK

Q900

TU+5V REGQ601

BATTBATTERY CHECK

Q902

BACK-UPDETECT

Q906,907

MUTEQ404

D400

D702

F900

R-CH

L

R

FRONTAUDIO OUT

R-CH53

AP2AP1

R-CH

L

RAUX IN

PJ401

D912

BATTD915

CD SECTION A

MUTE CD SECTIONB

BATT

Signal Path R-CH is omitted due to same as L-CH.

: CD PLAY

: FM

: AM

(Page 13)

(Page 13)

15 15

CDX-V3800

CDX-V3800

3-3. BLOCK DIAGRAM DISPLAY SECTION

ACK ONSWITCH

Q800

X80132.768kHz

79

80

82

83

38

282927

39

47

75

77

LCD DRIVERIC501

KEYIN0

CLKCE

LCD SOLCD SCK

LCD CE

DIMMERKEYIN1

KEY ACK

46 DST SEL

XKEY ON

46 DST SEL

RESET

DOOR SW

2 IN 1OUT

X1A

X0A

X0

X1

X80018.432MHz

S802RESET

S800

9K

10K

FREQUENCYSELECT

6364

62

1

LCD501

LIQUIDCRYSTALDISPLAYPANEL

LED501,502LCD

BACK LIGHT

D801

S522(OPEN)

3I

50

51I

54|

SEG3

SEG50

COM4

COM1

|

CLDI

CE

DISP+B

65SIRCS IR

LED504-518,520-522,524,525

2 OUT

U COM+3.3V

( )

KEY MATRIXS501-521,523

26

SYSTEM CONTROLIC801 (3/3)

IR RECEIVERIC502

SHUT SW

LEDCONTROL

Q502

72

RESETIC802

DISPLAYBOARD

DIMMER

3-4. CIRCUIT BOARDS LOCATION

MAIN boardDISPLAY board

SENSOR board

SERVO board

SPEAKER board

tuner unit(TUX601)

1616

CDX-V3800

CDX-V3800

NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

THIS NOTE IS COMMON FOR PRINTED WIRINGBOARDS AND SCHEMATIC DIAGRAMS.(In addition to this, the necessary note is printedin each block.)

For schematic diagrams.Note: All capacitors are in F unless otherwise noted. (p: pF)

50 WV or less are not indicated except for electrolyticsand tantalums.

All resistors are in and 1/4 W or less unless otherwise

specified. f : internal component. C : panel designation.

For printed wiring boards.Note: X : parts extracted from the component side. Y : parts extracted from the conductor side. a : Through hole. : Pattern from the side which enables seeing.(The other layers' patterns are not indicated.)

A : B+ Line. Voltages and waveforms are dc with respect to ground

under no-signal (detuned) conditions. CD mechanism section (1/2, 2/2) no mark : CD PLAY Main (1/3), (2/3), (3/3) and Display sections no mark : FM

( ) : AM< > : CD PLAY

: Impossible to measure Voltages are taken with a VOM (Input impedance 10 M).

Voltage variations may be noted due to normal produc-tion tolerances.

Waveforms are taken with a oscilloscope.Voltage variations may be noted due to normal produc-tion tolerances.

Circled numbers refer to waveforms. Signal path.

J : CD PLAYF : FMf : AM

Caution:Pattern face side: Parts on the pattern face side seen from the(Side B) pattern face are indicated.Parts face side: Parts on the parts face side seen from the(Side A) parts face are indicated.

Q

C

These are omitted

EB

EThese are omitted

CB

CThese are omitted

BE

Note: The components identified by mark 0 or dotted linewith mark 0 are critical for safety.Replace only with part number specified.

WAVEFORMS

1 IC801 i; (XOA)

32.768 kHz

3.6 Vp-p

18.432 MHz

2 IC801 is (X0)

4.1 Vp-p

0.2 V/DIV, 20 sec/DIV

0.5 V/DIV, 0.1 sec/DIV

1 IC500 rd (XO)

16.9344 MHz

1.8 Vp-p

2 IC500 ts (EQO)

0.2 V/DIV, 0.2 sec/DIV

0.5 V/DIV, 0.5 sec/DIV

27 MHz

3 IC100 yg (CLKIN)

1.5 Vp-p

0.2 V/DIV, 0.2 sec/DIV

0.8 V to1.3 Vp-p

Servo Board (MODE: CD PLAY) Main Board

Ver. 1.3

17 17

CDX-V3800

CDX-V3800

1

A

B

C

D

E

F

G

H

I

2 3 4 5 6 7 8 9 10 11 12 13 14 15

SW3

SW2

TP63

TP64

TP57

TP58

TP61

TP62

TP59

TP60 BP1

BP2

BP3

TP551

TP552

TP553TP554

TP555

TP556

TP557

TP558

TP559

TP56

0

TP561 TP562TP563TP564

TP51 TP52

TP542

TP50

1

TP503TP504

TP60

3

TP601

TP621

C704

C702

C701

TP622

BP4

FMB3

FMB4

FMB5

TP23TP22

TP21

TP19

TP17

TP18

TP16

TP15

TP14

TP13

TP11

TP10

TP2

TP1

TP5

TP4

TP20

TP6

TP3

C703

TP56

TP53

TP55

FMB6

TP513

TP512

TP522

TP51

9

TP531 TP529TP527

TP528

TP530

TP523

TP524

TP525

TP521

TP24

TP12 TP8

TP9

C101

X541

TP541

CN500

C505

C707

C544

RB1

09

C545

C503

C504

C542

C546

C502

RB1

08

C551

C541

C543

R16

5

R170

R17

2

R176

R55

1

R50

6

R546

R70

7

R60

4

R543

R50

1

R502

R545

R171

R17

3R

177

R602

R503

R504R505

C506

R541

R60

0

R622

R70

1R

702

R703

R70

4

IC500

R625

R54

4

C400

C547

C548

C705

C103

C600

C531

R54

2

C706

C165 C160

CN1

IC70

0

FB50

1

C517

Q502

C501

C518

R54

7

C507

C512

R515

C516

R511

C405

C521

C515

R516

R51

4

R513

RB3

01

R51

2

R630

R104

R10

5R

628

R312R311

R403

C513

C508

C514

C301

C302

C202

IC200

CN401

C511

D90

8

D91

0

D906

C520

C510

C519

C509

R708

R631

FB503

FB50

2

R548

C540

L101

TP181

TP18

2TP

183

TP184

TP185TP186

TP187TP131

FMA3

FMA4

C623

C603

C159

IC101

C601

C621

TP188TP189

RB101RB102

RB1

03

RB104

RB105RB106

RB1

07RB110

RB111

C605

C163

RB113

C406

C407

RB112

C180

R508R509

R16

3

R166

R16

8

R180R404

R709

R601 R603

R621R624

R167 R16

9

R17

5

R181

R507

C162

C112R

106

R10

7

R10

8

R16

1

R162

R10

9

R11

0

R111

SW1

R11

2

R113

R11

4

R62

7

R164

C102

C708

R632

D101

Q50

1

C709

C183C

182

C181

C164

C161

C132

R178

X401

C166

IC100

C111

IC600

R40

5C304C305

C312C3

13

C402

C403

C404

R401R402

R10

1

R102

R10

3

C410

R629

L401

C201

C131

C303

IC300

IC400

C401

C408

D90

7

D90

9

C133

FB50

4

R605R606

R623R626

3-5. PRINTED WIRING BOARDS CD MECHANISM SECTION Refer to page 15 for Circuit Boards Location. : Uses unleaded solder.

(Page 20)

Ref. No. LocationD101 G-3D906 B-11D907 B-2D909 B-1D910 F-9

IC100 E-3IC200 B-11IC300 B-3IC400 C-2IC500 D-10IC600 H-2IC700 G-10

Q501 E-5Q502 E-9

SemiconductorLocation

1818

CDX-V3800

CDX-V3800

Refer to page 16 for Waveforms.

3-6. SCHEMATIC DIAGRAM CD MECHANISM SECTION (1/2) Refer to page 26 for IC Block Diagrams. Refer to page 27 for IC Pin Description of IC500.

IC B/D

IC B/D

IC B/D

BP3

BP4

BP2

BP1

TP60

CN500

C505

C540

C605

C544

C545

C503

C504

C542

C541

R551

R546

R621

R624

R54

3

R545

R505

C506

TP57

R600

R622

TP551TP552

TP553

TP554

TP555TP556TP557TP558TP559TP560TP561TP562TP563TP564

TP51TP52

TP503

TP504

TP501

TP502

TP541

TP542

TP601

TP603

TP621

TP622

TP63

TP61

TP58

TP59

TP62

TP64

C705

C531

CN1

C518

C507

C512

C516

C521

C515

R516

R512

C513

TP55

TP53

TP51

1

TP56

C514

C511

C708

C510

R623

C519

R626

R509 R508

R507

R506

C707

C502

R547

R542

R511

R513

R514

R515

R603

R604

R602R601

FB501

R54

4

C543

R606

R605

C600

R627

C551

R708

C501C508

M901

M902

M903

S901

SW3

SW2

SW1

Q501

IC600

IC500

IC700

C517

Q502

R625

C546

R709

C709

R707

C706

C509

C547 C548

X541

R541

R548

R632

D91

0

R501R502

R503

R504

TP519

TP531

TP522

TP526TP525

TP521

TP524

TP528

TP530

TP527

TP523

TP529

TP513

TP512

TP5

TP1

TP2

TP20

TP4

TP6

TP3

TP10

TP8

TP12

TP9

TP11

TP13TP14TP15

TP18

TP16TP17

TP7

TP19

TP21TP22TP23

TP24

(Page 19)

(Page 23)

Ver. 1.3

19 19

CDX-V3800

CDX-V3800

Refer to page 16 for Waveform.

3-7. SCHEMATIC DIAGRAM CD MECHANISM SECTION (2/2) Refer to page 26 for IC Block Diagram. Refer to page 29 for IC Pin Description of IC400.

IC B/D

BP7

R163

R165

C112

R164

TP131

TP181

TP18

5 TP18

7

TP188TP189

C102

C182C181

C164

C132

X401

C111

C304

C305

C312

C313

C402

C403

C404

C405

R403 TP401

TP402

C301

L401

C302

C202

C131

C303

CN401

C401

C103

R162

R176

RB107

R312

R311

R11

2R

113

R11

4R11

1

R10

9R

110

R629

R404

R402

C183

TP18

6

TP18

3TP

182

TP18

4

R102

R101

C165

C180R180

C162C166C163C161

C160

R401

CN401

D101

IC100

FB503

IC400

FB502

IC300

RB1

11

RB1

10

RB106

RB105

RB104

RB103

RB102

RB101

RB1

12

R630

R631

RB301R

B113

R181

R405

C407

C406

R161

C133

FB504

IC200

C201

C410 D907

C400

D906

D90

9

R178

R702R703

R704

R172R170R168R166

R701

R16

7R

169

R17

1R

173

R17

5R

177

R10

6R

107

R10

8

R10

3R

104

R10

5

RB1

09

RB1

08

(Page 18)

2020

CDX-V3800

CDX-V3800

1

A

B

C

D

E

F

G

H

I

J

2 3 4 5 6 7 8 9 10 11 12 13 14

JW204 JW205

JW206JW207

5 6 7 81 2 3 4

JW203

JW200

JW202

JW201

R843

R849

R850

D90

2

C420

C423

C422

R421

C421

R420

R41

7

R416

R41

5

R41

4

R442

R40

7

R40

6

R40

5

R40

4

R413R408

C113R418

R412

D600

R424

R402

R403

C409

D400

C408

Q601

Q40

4 Q402

Q401

D301

R41

9

Q40

3

R606

R60

7

R608

R834R832

R705JR10D702

JR12R83

9

R84

0 R84

1

R84

7

R846

R702

C709

R81

3D912

D915

Q90

2

R931

C443

Q70

1

R828

R409

R83

0

IC80

1

D918

Q405

R82

3

R82

2

R82

1

R801

D802

R804

R916

R80

6

C807

FB70

2

D701

C816

C817

R83

5

R836

Q900

R903 R902

R443

C612

R80

5

R800

FB90

2

R817

R816

R92

7

R819

R936

C992

C433C434C435C436

R411

R43

0

C620

Q40

0

R809

R70

1

R44

1

D801

R860

R901

R818

R810

R440

R436 R43

5

L703

C614

R615

Q70

3

R848

R837

Q40

7

R70

3

R70

9

R437

L602

Q406

R925

D808

Q800

C451

JR5

C450

R468 R708

D90

3

R814

R873

C812

R30

2

D825

C437

IC802

R425

C440

C444

R427

R428

R432

Q906

C438

R932

R91

3

D914

C303

R448

C441

C446

R447

R426C8

21

C822

R824R825

R826

FB90

1

C815

R904

C706

Q907

C991

JR6

C990

FMB3

FMB4

C994

R853

R854

IC40

1

C993C439

R81

2D823

L400

C416

D916

JW39

D922

JW85S800

JW59

JW107

JW10

5

JW111

JW100

C705

JW95

C106

C813

JW123C4

11

JW122

C424

C428

D917

JW11

7

JW52

JW37

C414

JW77

C413

C412

JW56

C410

R429

JW14

CNP901

F901

IC100

PJ401

JW11

0

JW41

JW10

JW106 JW99

JW93

JW91

X801

JW19

C447

JW10

4

JW68

JW55

JW98JW109

JW108

C922

JW67

JW11

5

JW86

JW49

JW66

JW63

JW120

JW28

JW65

JW92

D921

JW62

JW24

JW83

JW10

3

D919

JW70

JW34

JW5

JW78JW60L701

L702

C707

JW84

C704

C809

L900

JW127

JW36

X800

C810

JW45

JW22

JW20

JW79

JW128

C908

R604

C701

JW6

JW11

9

JW134

JW8

R845

C101

R91

7

JW50

L700

JW47

R603

JW82

R400

JW42 JW31

JW35

JW14

1

JW61

CN75

1

JW30

JW94

JW51

JW11

3

JW72JW14

0

JW80

R928

JW69

JW124

JW27

TUX601

JW151

R833

JW11

6

JW76

JW11

JW11

4

JW97

JW3

C619

D90

7

JW10

2

JW18

JW145

JW144

JW9

JW73

JW38

JW131

JW96

JW75

C426

JW64

C425

C453

C452

JW43

JW48

JW143

D908

JW10

1

S802

S802RESET

JW29

JW130

C111

JW74

C107

D90

6

JW121

JW12

PJ601

C825

R401

JW54

CNP800

DISPLAY BOARDCN901

SERVO BOARD

CN1

JW46

C109

R81

5

JW126

JW150

C618

D909

R431

JW44

C711

R912

C430

JW13

D82

0

C454

JW40

C417

JW11

2

JW17

JW125

JW15

JW14

2

JW11

8

JW25

JW1

JW2

JW4

JW58

1-865-780- 11

1-865-781- 11

S800FREQUENCY

SELECT

D90

5

D90

4

D81

7

D81

3

D81

6

D81

4

D81

2

D81

1

D81

5

3-8. PRINTED WIRING BOARDS MAIN SECTION Refer to page 15 for Circuit Boards Location. : Uses unleaded solder.

(Page 17)

(Page 24)

D301 E-2D400 D-4D600 E-2D701 G-7D702 G-6D801 I-6D802 I-5D808 J-9D811 I-3D812 I-3D813 I-3D814 I-2D815 I-2D816 I-2D817 I-2D820 I-4D823 J-4D825 J-4D902 B-7D903 B-8D904 C-6D905 C-6D906 C-7D907 C-7D908 C-7D909 C-7D912 E-10D914 C-9D915 E-10

Semiconductor LocationRef. No. Location

D916 C-8D917 C-8D918 C-9D919 D-9D921 D-6D922 C-6

IC100 B-6IC401 F-4IC801 H-7IC802 H-10

Q400 D-4Q401 D-4Q402 C-4Q403 D-3Q404 C-3Q405 C-3Q406 C-3Q407 C-3Q601 E-2Q701 F-10Q703 F-10Q800 I-6Q900 H-10Q902 F-10Q906 G-10Q907 G-10

Ref. No. Location

21 21

CDX-V3800

CDX-V3800

3-9. SCHEMATIC DIAGRAM MAIN SECTION (1/3) Refer to page 26 for IC Block Diagram.

IC B/D

D60

0

JR6

L400

L602

Q400

JR10

C430

C618

C424

C425

C428

C452

C426

C619

C453

Q401 D400

C612

C614

R615

C620

C416 C417

C421

C420

R416

R415

R421

R420

R419

R414

C423

C422

R417

R418

R442

R440

R441

C450

C451 R443

C437 R427

C438

C444

R429

R432

C440 R431

R302 C303

R468

C436

IC401

R424

D301

C435

C439

C443

R401

R400

R606

R604

R603

R608

R607

PJ601

TUX601Q601

R402

R403

D702

Q407

Q406

Q402

Q403

Q404

Q405

C433

C434

R425 R426

R428 R430

C414

C411

C410

C409

C408

C413

C454

C412

R404

R406

R405

R407

R409

R411

R412

R436R435

R408R413

(Page 23)

(Page 22)

2222

CDX-V3800

CDX-V3800

Q902

C106

C922

D918

D921

D922

D91

9

C908

FB901

FB902

C706

R825R448

C441

C446 R447

C113

C993 C991

C990

R903

R902 R904 R912

R913

R931

C992

C994

C447

C111

R932

D912

F901

CNP901

C107

C101

IC100

C109

D914

L900

R824

Q906

Q907

D915Q900

D90

2

D90

3

D90

4

D90

6

D90

7

D90

8

D91

7

D91

6

D90

5

D90

9

R928

R917

3-10. SCHEMATIC DIAGRAM MAIN SECTION (2/3)

(Page 21)

(Page 23)

23 23

CDX-V3800

CDX-V3800

Refer to page 16 for Waveforms.

3-11. SCHEMATIC DIAGRAM MAIN SECTION (3/3) Refer to page 30 for IC Pin Description of IC801.

IC802

L701

R853R936

C809

C813

X801D801

TP11

R708

CN751

C701

C704

C707

C711

D820

R813

X800

Q701

C709

R833

R702

R701C807 R826

R927

R814

R849

R804

R801

C821

R818

R834 R832

R705

C822

R848

C812

C815

R437

R925

R901

FB702

L702

C705

CNP800

R805

R806

D802

R819

R828

R830

R854

JR12

R816

C825R837

R836

R860

R845

S800

R815

Q800

S802

JR5

D701

R709

R703

R843

L700

L703

Q703

R800R809

R812

R817

R835

R916

C816 C817

D80

8

R846

R847

R810

C810

IC801

R850

R873

D81

7

D81

5

D81

6

D81

4

D81

3

D81

2

D81

1

D82

3

D82

5

R822

R823

R821

R83

9

R84

0

R84

1

(Page 21)

(Page 18)

(Page 25)

(Page 22)

2424

CDX-V3800

CDX-V3800

1

A

B

C

D

E

F

G

H

2 3 4 5 6 7 8 9 10 11 12 13 14

LCD501LIQUID CRYSTAL DISPLAY PANEL

DSPLATT

EJECT MODE SEL 5/OSD1/REP 4/AUDIO 6/PAUSE3/SLOW2/SHUF SENS/ ALBUM BTM/+ SCRL

EQ3

EJECT

OFF

SEEK

LED515,S503

LED516,S514

LED517,S513

SOURCE

1-865-782- 11

MAIN BOARD CNP800

B

1-865-782- 11

LED507,S509

LED521,S507

LED520,S508

(VOLUME)

1

4

2

3

LED513,S516

LED501(LCD BACK LIGHT)

LED502(LCD BACK LIGHT)

LED514,S515

LED522

LED503(CD WINDOW)

LED

515

LED525

S522 (OPEN) LED

502

LED524

LED514

LED

501

IC502

LED518LED504LED505 LED506

LED

507

LED508LED509LED510LED511

LED512

LED513

LED516

LED517

LED520

LED521

S507

S508

S502 LED524,S504 LED525,S505

S516

LED522,S506 LED505,S511 LED504,S512 LED511,S521 LED510,S520 LED509,S519 LED508,S518 LED506,S510 LED518,S523 LED512,S517

S515

S513 S503

S514

S501 IC502

FMB3

FMB4

CN901

R555

D55

1

R55

2

D50

2

R576

R577

R579

R578

R516

D55

2

R51

7

R56

1

R56

0

D505

D50

4

R553

C551

C553

D50

3

R57

3

R513

R55

1

R558

R55

4

R519

R502

R503

R504

R505

R506

R509 R510

R57

1

R574

R518

R580

R501

R511

R575

R514

R515

Q502

R572

R512

R55

9

R508

R507

R536R537

R531R532

R533

R535

C960

R557

IC501

2 12

1 11

3-12. PRINTED WIRING BOARD DISPLAY SECTION Refer to page 15 for Circuit Boards Location. : Uses unleaded solder.

(Page 20)

Ref. No. LocationD502 F-13D503 G-11D504 F-13D505 G-12D551 H-10D552 G-10

IC501 G-7IC502 D-14

Semiconductor LocationRef. No. LocationLED501 C-4LED502 C-12LED503 B-7LED504 D-6LED505 D-6LED506 D-11LED507 A-2LED508 D-10LED509 D-9

Ref. No. LocationLED510 D-8LED511 D-7LED512 D-12LED513 C-3LED514 C-12LED515 A-14LED516 C-14LED517 B-13LED518 D-11

LED520 D-2LED521 B-2LED522 D-5LED524 D-3LED525 D-4

Q502 G-10

Ref. No. Location

25 25

CDX-V3800

CDX-V3800

3-13. SCHEMATIC DIAGRAM DISPLAY SECTION

LED501

LED502

CN901

R531

R532

R533

R535

R536

R537

S522

R501 R502 R504 R505 R506 R507 R508 R509 R510

R511 R512 R513 R514 R515 R503 R516 R517 R518 R519

R552

R551

R553

R554

R558

R559

R560

IC501

R555

R561

C960

C551IC502

C553 R557

LCD501

D552

D55

1

LED503

LED515

LED517

LED514

LED516 LED508

LED506

LED518

LED512 LED509

LED510

LED504

LED505

LED522

LED525

LED524

LED513

LED521

LED507

LED520

R571 R573 R575 R577 R579

R572 R574 R576 R578 R580

Q502

LED511

D50

2

D50

3

D50

4

D50

5

S517S514 S519 S520S515 S521S516 S518 S505 S523S513

S508 S509S504 S506 S507S503S502 S511S510 S512S501

(Page 23)

2626

CDX-V3800

CDX-V3800

IC500 BU9536KS2 (SERVO Board (1/2))

IC BLOCK DIAGRAMS

51 5052

1

RF SIGNAL GEN.

DIGITALSIGNAL

PROCESSOR

APC

AVDD

ACBD

VBIASEF

AGND

FENFEOPKCBTCPDLD

EFLAG

EQO

RFI

CAGC

TEN

TEO

SC TZCR

FMRF

RPRF

N

JUM

POTD

OUT

SDIN

SDOU

TFD

OUT

CLVO

UT CLK

LON

CLK8

8

ASY

FCO

PCO

MCK

DGND

XO XI DVDD

XPLC

K

XBUFO

DCKLRCKDOUTAWFCKSUBCK

SUBDATASUBSYQ

BUSYRESETXR/WDIO

SERV

O SI

GNAL

GEN.

2

49 48 47 46 45 44 43 42 41 40

3456

7

89

10111213

14 15 16

272829303132

363738

333435

39

17 18 19 20 21 22 26252423

PLL

DIGITALSERVOFILTER

DIGITAL SERVOSIGNAL

PROCESSOR

16KSRAM

COMMANDINTERFACE

+

+ +

REV

FWD

OUT F

OUT R

+

+

+

+

+

+

MUTE

+ + +

+ + + +

LEVELSHIFT

LEVELSHIFT

+

LEVELSHIFT +

LEVELSHIFT

+

+

VCC

LOADING DRIVER

24 23 22 21 20 19 18 17 16 15

4 5 6 7 8 9 10 11 12 13 1421 3

2728 26 25

REV

OPIN

4(+)

OPIN

4()

OPOU

T4

OPIN

3(+)

OPIN

3()

OPOU

T3

MUT

E

BIAS

GND

VO3(

)

VO3(

+)

VO4(

)

VO4(

+)

FWD

OPIN

1(+)

OPIN

1()

OPOU

T1

OPIN

2(+)

OPIN

2()

OPOU

T2

VCC

VOL(

)

VOL(

+)

VO2(

)

VO2(

+)

VO1(

)

VO1(

+)

SERIALINTERFACE

DIGITALFILTER

LRCINDIN

BCKIN

NC

CAP

VOUTR

GND

DIGITALSIGMA-DELTAMODULATOR

SWICHEDCAPACITOR

DAC

12

3

4

5

6

7

DIGITALSIGMA-DELTAMODULATOR

SWICHEDCAPACITOR

DAC

SCKIFORMAT

DEEMPH

MUTENC

VOUTL

VDD

1413

12

1011

9

8

FSADJUSTDATA7DATA6DATA5DATA4DATA3DATA2DATA1DATA0

CVBS

/Y

32

AGND

31

TEST

30

HSYN

C

29

VSYN

C

28

VDD

27

DGND

26

CLKO

UT

25

SLEE

P

9

9

LUM

A

10

CBSW

P

11

MAS

TER

12

MOD

EA

13

MOD

EB

14

CLK

15

XTAL

O

16

1

COMP 2

VREFOUT 4

VAA 3

VBIAS 6VREFIN 5

DAC

LATCH

1.3MHzLPF

2XUPSAMPLE

MOD.ANDMIXER

INTERNALVREF

7AGND 8

VBIGENERATOR

2423222120191817

32 31 30 29 28 27 26 25 24 23 22

I2C BUSLOGIC

VCO

MIX

FADER(0~-58,-dB)

FADER(0~-58,-dB)

FADER(0~-58,-dB)

FADER(0~-58,-dB)

VOLUME(+23~-79dB,-dB

1dB STEP)

VOLUME(+23~-79dB,-dB

1dB STEP)

INPUT GAIN(0~15dB,1dB STEP)

INPUT SELECTOR(4 STEREO INCLUDE 1 ISOLATION INPUT)

INPUT GAIN(0~15dB,1dB STEP)

ANTI-ALIASINGFILTER

ANTI-ALIASINGFILTER

MUTE

fc:40kHz fc:40kHz

MUTE

6 7 8 9 10 113 4 521

DGND

AGND FI

L

AN AP2

AP1 B1 B2 C1 C2 NC NC NC NC NC NC NC

12 14 1613 15

SDA

SCL

MUT

E

SEL

ADJ

VCC

OUTF

1

OUTR

1

OUTF

2

OUTR

2

NC NC NC OUTS

1

OUTS

2

21 20 19 18 17

VCC

VCC/2

TONEPASS

BASSfo:60,70,80,100,120,140,160,200HzQ:0.5,0.75,1,1.25

MIDDLEfo:500Hz,1kHzQ:1

TABLEfo:5,7.5,10,12.5kHz

TONEPASS

EFFECT (0dB~+20dB,2dB STEP)

EFFECT (0dB~+20dB,2dB STEP) 2ND ORDER

LPF

2ND ORDER LPFfc:OFF,80,120,160HzQ: 0.707

BASS,TREBLE, MIDDLE(-15dB~+15dB,1dB STEP)

BASS,TREBLE, MIDDLE(-15dB~+15dB,1dB STEP)

GAIN+ATT(+10~-29,

-dB)

IC401 BD3806FS-E2 (MAIN Board (1/3))

IC700 WM8726GED/R (SERVO Board (1/2)) IC400 SPCA717A-HL211 (SERVO Board (2/2))

IC600 BA5966FP-FE2 (SERVO Board (1/2))

27

CDX-V3800

IC PIN DESCRIPTIONS IC500 BU9536KS2 (RF AMP, DIGITAL SERVO) (SERVO BOARD (1/2))

Pin No. Pin Name I/O Pin Description

1 AVDD1 Analog power supply pin (+3.3 V)

2 AC I A+C voltage signal input from optical pick-up block

3 BD I B+D voltage signal input from optical pick-up block

4 VBIAS O Bias level (VDD/2) signal output

5 E I E voltage signal input from optical pick-up block

6 F I F voltage signal input from optical pick-up block

7 AGND1 Analog ground pin

8 FEN I Focus error amplifier feedback signal input

9 FEO O Focus error signal output

10 PKC O RF signal peak detection capacitance connected pin

11 BTC O RF signal bottom detection capacitance connected pin

12 PD I APC photo detecter signal input

13 LD O APC laser drive signal output

14 PCO O PLL PCO signal output

15 FCO O PLL FCO-DAC signal output

16 ASY I Asymmetry revice and ccomparator slice capacitor install pin

17 JUMPO O Tracking jump pulse signal output

18 TDOUT O Tracking drive signal output

19 SDIN I Sled signal input

20 SDOUT O Sled drive signal output

21 FDOUT O Focus drive signal output

22 CLVOUT O CLV drive signal output

23 CLK88 O Clock signal output for driver IC Not used in this set. (Open)

24 LON O Laser on control signal output

25 CLK O Clock signal output Not used in this set. (Open)

26 MCK I Transfer clock signal input for sub Q and command

27 DIN/DOUT I/O Command signal input/status, sub-Q signal output

28 R/W I Read/write signal input for command

29 RESETX I System reset signal input L: reset

30 BUSY O Busy signal output

31 SUBSYQ O Sub cord synchronizing signal output

32 SUBDATA O Sub cord data signal output

33 SUBCK I Sub cord bit clock signal input Not used in this set. (Fixed at L.)

34 WFCK O Disc frame synchronizing signal output

35 DOUTA O Audio serial data signal output

36 LRCK O Audio LR signal output

37 DCK O Audio serial bit clock signal output

38 EFLAG I/O Error flag signal input/output

39 BUFO O X'tal 16.9344 MHz buffer signal output Not used in this set. (Open)

40 XPLCK I/O XPLCK signal input/output Not used in this set. (Open)

41 DVDD Digital power supply pin (+3.3 V)

42 XI I X'tal 16.9344 MHz connect input

43 XO O X'tal 16.9344 MHz connect output

44 DGND Digital ground pin

45 RFRPPFM O RFRP capacitor install pin or RF test monitor signal output

46 TZCRFM O TZC capacitor install pin or RF monitor signal output

47 SC I Scratch depth adjustment resistor connected pin

48 TEO O Tracking error signal output

28

CDX-V3800

Pin No. Pin Name I/O Pin Description

49 TEN I Tracking error amplifier feedback signal input

50 CAGC I RFAGC capacitor install pin

51 RFI I RF signal input

52 EQO O RF equalizer signal output

29

CDX-V3800

IC400 SPCA717A-HL211 (VIDEO SIGNAL PROCESSOR) (SERVO BOARD (2/2))Pin No. Pin Name I/O Pin Description

1 FSADJUST Full-Scale adjust control pin The Full-Scale current of D/A converters can be

adjusted by connecting a resistor (RESET) between this pin and ground.

2 COMP Compensation pin A0.1 F ceramic capacitor must be used to bypass this pin to VAA.

The lead length must be kept as short as possible to avoid noise.

3 AVCC Analog power supply pin (+3.3 V)

4 VREF OUT OVoltage reference signal output It generates typical 1.2 V voltage reference and may

be used to drive pin 5 (VREF IN) directly.

Voltage reference signal input An external voltage reference must supply typical

5 VREF IN I1.235 V to this pin. A0.1 F ceramic capacitor must be used to de-couple this input

to ground. The decoupling capacitor must be as closed as possible to minimize the

length of the load. The pin may be connected derectry to pin 4 (VREF OUT).

6 VBIAS DAC bias voltage Potential normally 0.7 V less than pin 2 (COMP).

7 NC Not used. (Open)

8 AGND Analog ground pin

Power save mode A logic high on this pin puts the chip into power-down mode. This

9 SLEEP I pin is equal to reset pin. An external logic high pulse should input to the pin when

power on.

10 SVIDEO IVideo signal selection pin A logic high selects Y output. A logic low selects

composite video output. Not used in this set. (Fixed at L.)

11 CBSWAP ICr and Cb pixel sequence configuration pin A logic high swap the Cr and Cb sequence.

Not used in this set. (Fixed at L.)

12 MASTER IMaster/Slave mode selection A logical high for master mode operation. A logical 0

for slave mode operation. Not used in this set. (+3.3 V)

13 MODEA I Mode configuration pin Not used in this set. (Fixed at L.)

14 MODEB I Mode configuration pin

15 CLK I27 MHz crystal oscillator input A crystal with 27 MHz clock frequency can be

connected between this pin and pin qh (XTALO).

16 XTALO O Crystal oscillator output Not used in this set. (Open)

17 to 24 P0 to P7 IYCrCb pixel inputs

They are latched on the rising edge of CLK.

25 CLKOUT O Pixel clock signal output Not used in this set. (Open)

26 DGND Digital ground pin

27 VDD Digital power supply pin (+3.3 V)

28 VSYNC I/OVertical sync input/output

VSYNC is latched/output following the rising edge of CLK.

29 HSYNC I/OHorizontal sync input/output

HSYNC is latched/output following the rising edge of CLK.

30 TEST I Test pin These pins must be connected to digital ground.

31 AGND Analog ground pin.

32 CVBSY OComposite/Luminance output. This is a high-impedance current source output. The

output format can be selected by the PAL pin. The CVBSY can drive a 37.5 load.

30

CDX-V3800

IC801 MB90488BPF-G-135-BNDE1 (SYSTEM CONTROL) (MAIN BOARD (3/3))Pin No. Pin Name I/O Pin Description

1 LINE ATT O Audio mute control signal output

2 to 4 NC Not used in this set. (Open)

5 BEEP O Beep signal output to power amp IC

6 VOL ATT O Electrical volume ATT control signal output

7 to 10 NC Not used in this set. (Open)

11 VSS Ground pin

12 to 14 NC Not used in this set. (Open)

15 TU ATT O Tuner mute control signal output

16, 17 NC Not used in this set. (Open)

18 CD SI I CD servo serial data signal input

19 CD SO O CD servo serial data signal output

20 CD SCK O CD servo serial clock signal output

21, 22 NC Not used in this set. (Open)

23 VCC+3.3 Power supply pin (+3.3 V)

24 EEP SIO I/O Serial data signal input/output for EEPROM communication

25 EEP SCK O Serial clock signal output for EEPROM communication

26 SHUT SW IShutter switch open/close detect signal input

L: Panel open, H: Panel close Not used in this set. (Open)

27 LCD CE O Chip enable signal output to LCD driver IC

28 LCD SO O Serial data signal output to LCD driver IC Flash: UART serial out

29 LCD SCK O Serial clock signal output to LCD driver IC

30 NC Not used in this set. (Open)

31 STB O Standby signal output to power amp IC

32 AUX Not used in this set. (Open)

33 IIC SCK O IIC bus serial clock signal output

34 IIC SIO I/O IIC bus serial data signal input/output

35 VCC+3.3 Power supply pin (+3.3 V) (for A/D converter)

36 AVRH+3.3 External reference power supply (+3.3 V) (for A/D converter)

37 AVSS Ground pin (for A/D converter)

38, 39 KEY IN0, 1 I Key signal input

40 NC Not used in this set. (Open)

41 NC Not used in this set. (Fixed at H.)

42 VSS Ground pin

43, 44 NC Not used in this set. (Fixed at L.)

45 VSM I S meter voltage detect signal input

46 DST SEL I Destination select pin

47 KEY ACK I Key acknowledge detect signal input

48 NC Not used in this set. (Open)

49, 50 MD0, 1 I Input for operation mode designation (Fixed at H.)

51 MD2 I Input for operation mode designation (Fixed at L.)

52 NC Not used in this set. (Open)

53 BU IN I Back up power supply detect signal input

54 SP O SP mode select signal output

55 CD SELFSW I CD mechanism self load position detect switch signal input

56 DIAG I Condition input from power amp IC

57 NC Not used in this set. (Open)

58 UNI SI I Serial data signal input

59 UNI SO O Serial data signal output

60 UNI SCK O Serial clock signal output Not used in this set. (Open)

61 BUS ON O Bus on signal output

62 SYS RST O System reset signal output

63 NC Not used in this set. (Open)

31

CDX-V3800

Pin No. Pin Name I/O Pin Description

64 ACC IN I Accessory power supply detect signal input

65 SIRCS I Remote control signal (infrared rays) input

66 NC Not used in this set. (Fixed at L.)

67 PAK BK I Test mode detect signal input

68 FLASH W IMemory mode changeover signal input

Normally H input (single chip mode) L after reset: Flash write mode

69 to 71 NC Not used in this set. (Open)

72 DOOR SW IFront panel open/close detect signal input

L input: Panel close, H input: Panel open

73, 74 NC Not used in this set. (Fixed at H.)

75 XKEY ON O Key power supply control signal output Pin rj (KEY ACK) active: L output

76 NC Not used in this set. (Open)

77 RESET I Reset signal input

78 NC Not used in this set. (Open)

79 X1A Oscillator connect pin (32.768 kHz)

80 X0A Oscillator connect pin (32.768 kHz)

81 VSS Ground pin

82 X0 Oscillator connect pin (3.68 MHz)

83 X1 Oscillator connect pin (3.68 MHz)

84 VCC+3.3 Power supply pin (+3.3 V)

85, 86 NC Not used in this set. (Open)

87 CD ON O CD power on/off control signal output

88 NC Not used in this set. (Open)

89 TEST MODE I Test mode pin

90 MP O MP mode select signal output

91 NC Not used in this set. (Open)

92 CD IN SW I CD mechanism IN-SW detect signal input

93 CD LOAD O CD mechanism loading motor control signal output

94 EJECT O CD mechanism eject motor control signal output

95 D SW I CD mechanism DSW detect signal input

69, 97 NC Not used in this set. (Open)

98 CD XRST O CD servo reset signal output

99 NC Not used in this set. (Open)

100 NC Not used in this set. (Open)

32

CDX-V3800

Ref. No. Part No. Description Remark

4-1. MAIN SECTION

Ref. No. Part No. Description Remark

1 X-3384-407-1 PANEL (1) ASSY, SUB2 3-231-472-02 SCREW (+B 2X4)3 X-3382-588-1 LOCK ASSY (S)

* 4 3-246-006-31 COVER5 3-922-535-11 SCREW (+BTT)

6 1-829-847-11 CABLE, FLAT (FFC) 26P7 A-1096-245-A MAIN BOARD, COMPLETE

8 1-792-194-61 CORD (WITH CONNECTOR) (POWER)9 1-829-836-12 CORD, CONNECTION (VIDEO OUT)10 2-178-708-01 SHEET, SHIELDF901 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10ATUX601 A-3220-961-A TUNER UNIT (TUX-032)

#1 7-685-792-09 SCREW +PTT 2.6X6 (S)#2 7-685-793-09 SCREW +PTT 2.6X8 (S)

SECTION 4EXPLODED VIEWS

NOTE: The mechanical parts with no reference

number in the exploded views are not supplied. Items marked * are not stocked since

they are seldom required for routine service.Some delay should be anticipatedwhen ordering these items.

-XX and -X mean standardized parts, sothey may have some difference from theoriginal one.

Color Indication of Appearance PartsExample :

KNOB, BALANCE (WHITE) ... (RED)

Parts Color Cabinets Color Accessories are given in the last of this

parts list.

R R

The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.

F901

not supplied

TUX601

not supplied

not supplied

#1

#1

#1

#1

#2

#2

#1

MG-611MM-186//K

A

A

B

B

1

2

34

5

86

9

10

7

33

CDX-V3800

4-2. FRONT PANEL SECTION

Ref. No. Part No. Description RemarkRef. No. Part No. Description Remark

51 X-2024-914-1 PANEL (BASE) ASSY, FRONT52 3-258-879-01 FILTER (IR)53 1-780-120-11 CONDUCTIVE BOARD, CONNECTION54 X-3384-622-1 SHUTTER ASSY55 X-3384-457-2 BUTTON ASSY (S)

56 3-246-211-01 SPRING (RELEASE)57 3-258-884-01 SHEET (ILLUMINATOR)58 3-258-880-01 PLATE (CD), LIGHT GUIDE59 3-258-869-02 PANEL, FRONT BACK

60 X-3378-390-3 CASE ASSY (for FRONT PANEL)61 A-1096-248-A PANEL COMPLETED ASSY, FRONT62 3-258-874-12 BUTTON (SEEK)63 3-258-873-12 BUTTON (+.)64 X-3384-621-2 RETRACTABLE ASSY

65 3-258-875-31 BUTTON (PRESET)LCD501 1-805-451-11 DISPLAY PANEL, LIQUID CRYSTAL#3 7-685-105-19 SCREW +P 2X8 TYPE2 NON-SLIT

LCD501

not supplied

not supplied

#3

#3

not supplied

not supplied

not supplied

not supplied

not supplied

not supplied(DISPLAY board)

not supplied

51

62

6364

52

54

56 655553

57

58 59

6061

34

CDX-V3800

4-3. CD MECHANISM SECTION (1)(MG-611MM-186//K)

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

101 A-3372-455-A CHASSIS (T) SUB ASSY102 3-253-729-01 SPRING (LTR), TENSION COIL103 3-253-746-14 SPRING (DAMPER), COMPRESSION104 3-253-746-03 SPRING (DAMPER), COMPRESSION

105 2-345-767-01 SPRING (KF60), TENSION106 3-253-748-01 DAMPER (S)107 A-1107-620-A SERVO BOARD, COMPLETE#4 7-627-552-87 SCREW, PRECISION +P 1.7X2.2

not supplied(SENSOR board)

not supplied

not supplied

not supplied

not supplied

#4

#4

101102

103

104

105

106

107

35

CDX-V3800

4-4. CD MECHANISM SECTION (2)(MG-611MM-186//K)

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

151 A-1075-786-A CHASSIS (OP) COMPLETE ASSY152 3-316-938-91 SCREW (B1.4X5), TAPPING

0153 8-820-207-12 OPTICAL PICK-UP (KSS1000E/K1RP)154 A-1075-787-A CHASSIS (OP) SUB ASSY (including M901)155 A-3337-641-A ARM SUB ASSY, CHUCKING

156 A-3337-639-A LEVER (SL) SUB ASSY

157 X-3383-454-3 LEVER (SL) ASSY158 3-261-959-02 SPRING (SL), TORSIONM902 A-3337-638-A MOTOR ASSY, SL (SLED)SW4 1-571-099-11 SWITCH (1 KEY) (LIMIT)#5 7-627-850-77 SCREW, PRECISION +P 1.4X1.8

The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.

not supplied

SW4

not supplied

not suppliednot supplied

#5

M902

151152

153

154(including M901)

155

156

157

158

36

CDX-V3800

4-5. CD MECHANISM SECTION (3)(MG-611MM-186//K)

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

201 3-262-755-01 WASHER (1.1-2.5)202 2-186-699-11 GEAR (RA1)203 A-1075-789-A ARM ASSY, ROLLER204 3-259-455-02 SPRING (RAL)205 3-253-713-01 SPRING (RAR)

206 3-259-469-01 SPRING (LE), LEAF207 2-134-636-31 SCREW (M1.7X2.5)

208 2-186-696-11 BRACKET (LEM-N)209 3-345-648-91 SCREW (M1.4), TOOTHED LOCK210 A-1083-637-A GEAR (LE) ASSY211 2-186-697-11 BEARING (LEB-N)M903 A-1075-792-A MOTOR ASSY, LE (LOADING)

#4 7-627-552-87 SCREW, PRECISION +P 1.7X2.2

#4

M903

208 210

211

209

207

207

207

201202

203

204

205

206

37

CDX-V3800

4-6. CD MECHANISM SECTION (4)(MG-611MM-186//K)

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

251 2-186-700-11 GEAR (CHK1)252 3-344-223-01 WASHER253 3-259-470-01 GEAR (LE1)254 3-253-755-02 LEVER (D)

255 3-899-829-01 WASHER (SLIT)256 3-259-032-01 GEAR (LE2)257 A-1075-791-A CHASSIS (M) BLOCK ASSY

251

252

252254

255

256

257

253

38

CDX-V3800SECTION 5

ELECTRICAL PARTS LIST

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

DISPLAY BOARD**************

1-780-120-11 CONDUCTIVE BOARD, CONNECTION3-258-884-01 SHEET (ILLUMINATOR)

< CAPACITOR >

C551 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC553 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10VC960 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

< CONNECTOR >

CN901 1-794-312-21 PIN, CONNECTOR 12P

< DIODE >

D502 8-719-977-12 DIODE DTZ6.8BD503 8-719-977-12 DIODE DTZ6.8BD504 8-719-977-12 DIODE DTZ6.8BD505 8-719-977-12 DIODE DTZ6.8BD551 8-719-080-28 DIODE KDZ5.1V

D552 8-719-988-61 DIODE 1SS355TE-17

< IC >

IC501 6-707-063-01 IC LC75826WH-US-EIC502 6-600-384-01 IC KSM-401E (IR)

< LIQUID CRYSTAL DISPLAY >

LCD501 1-805-451-11 DISPLAY PANEL, LIQUID CRYSTAL

< DIODE >

LED501 6-500-459-01 LED NSCW505T-ARS (LCD BACK LIGHT)LED502 6-500-459-01 LED NSCW505T-ARS (LCD BACK LIGHT)LED503 8-719-053-09 LED SML-310VTT86 (CD WINDOW)LED504 8-719-053-09 LED SML-310VTT86 (2/SHUF)LED505 8-719-053-09 LED SML-310VTT86 (1/REP)

LED506 8-719-053-09 LED SML-310VTT86 (SENS/ALBUM )LED507 8-719-053-09 LED SML-310VTT86 (ATT)LED508 8-719-053-09 LED SML-310VTT86 (6/PAUSE)LED509 8-719-053-09 LED SML-310VTT86 (5/OSD)LED510 8-719-053-09 LED SML-310VTT86 (4/AUDIO)

LED511 8-719-053-09 LED SML-310VTT86 (3/SLOW)LED512 8-719-053-09 LED SML-310VTT86 (SCRL)LED513 8-719-053-09 LED SML-310VTT86 (DSPL)LED514 8-719-053-09 LED SML-310VTT86 (EQ3)

LED515 8-719-053-09 LED SML-310VTT86 (OFF)LED516 8-719-053-09 LED SML-310VTT86 (SEEK /m .)LED517 8-719-053-09 LED SML-310VTT86 (SEEK +/> M)LED518 8-719-053-09 LED SML-310VTT86 (BTM/ALBUM +)LED520 8-719-053-09 LED SML-310VTT86 (VOL )

LED521 8-719-053-09 LED SML-310VTT86 (VOL +)LED522 8-719-053-09 LED SML-310VTT86 (SEL)LED524 8-719-053-09 LED SML-310VTT86 (SOURCE)LED525 8-719-053-09 LED SML-310VTT86 (MODE)

< TRANSISTOR >

Q502 8-729-038-67 TRANSISTOR KRC102S

< RESISTOR >

R501 1-216-819-11 METAL CHIP 680 5% 1/10WR502 1-216-819-11 METAL CHIP 680 5% 1/10WR503 1-216-823-11 METAL CHIP 1.5K 5% 1/10WR504 1-216-819-11 METAL CHIP 680 5% 1/10WR505 1-216-821-11 METAL CHIP 1K 5% 1/10W

R506 1-216-823-11 METAL CHIP 1.5K 5% 1/10WR507 1-216-823-11 METAL CHIP 1.5K 5% 1/10WR508 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR509 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR510 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R511 1-216-819-11 METAL CHIP 680 5% 1/10WR512 1-216-819-11 METAL CHIP 680 5% 1/10WR513 1-216-819-11 METAL CHIP 680 5% 1/10WR514 1-216-821-11 METAL CHIP 1K 5% 1/10WR515 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R516 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR517 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR518 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR519 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10WR531 1-216-813-11 METAL CHIP 220 5% 1/10W

R532 1-216-813-11 METAL CHIP 220 5% 1/10WR533 1-216-813-11 METAL CHIP 220 5% 1/10WR535 1-216-815-11 METAL CHIP 330 5% 1/10WR536 1-216-809-11 METAL CHIP 100 5% 1/10WR537 1-216-809-11 METAL CHIP 100 5% 1/10W

R551 1-216-815-11 METAL CHIP 330 5% 1/10WR552 1-216-815-11 METAL CHIP 330 5% 1/10WR553 1-216-821-11 METAL CHIP 1K 5% 1/10WR554 1-216-821-11 METAL CHIP 1K 5% 1/10WR555 1-216-821-11 METAL CHIP 1K 5% 1/10W

NOTE: Due to standardization, replacements in

the parts list may be different from theparts specified in the diagrams or thecomponents used on the set.

-XX and -X mean standardized parts, sothey may have some difference from theoriginal one.

RESISTORSAll resistors are in ohms.METAL:Metal-film resistor.METAL OXIDE: Metal oxide-film resistor.F:nonflammable

Items marked * are not stocked sincethey are seldom required for routine service.Some delay should be anticipatedwhen ordering these items.

SEMICONDUCTORSIn each case, u : , for example:uA.. : A.. uPA.. : PA..uPB.. : PB.. uPC.. : PC.. uPD.. : PD..

CAPACITORSuF : F

COILSuH : H

The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.

When indicating parts by referencenumber, please include the board.

DISPLAY

39

CDX-V3800

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

R557 1-216-821-11 METAL CHIP 1K 5% 1/10WR558 1-216-821-11 METAL CHIP 1K 5% 1/10WR559 1-216-821-11 METAL CHIP 1K 5% 1/10WR560 1-216-821-11 METAL CHIP 1K 5% 1/10WR561 1-216-857-11 METAL CHIP 1M 5% 1/10W

R571 1-216-809-11 METAL CHIP 100 5% 1/10WR572 1-216-809-11 METAL CHIP 100 5% 1/10WR573 1-216-809-11 METAL CHIP 100 5% 1/10WR574 1-216-809-11 METAL CHIP 100 5% 1/10WR575 1-216-809-11 METAL CHIP 100 5% 1/10W

R576 1-216-809-11 METAL CHIP 100 5% 1/10WR577 1-216-809-11 METAL CHIP 100 5% 1/10WR578 1-216-809-11 METAL CHIP 100 5% 1/10WR579 1-216-809-11 METAL CHIP 100 5% 1/10WR580 1-216-809-11 METAL CHIP 100 5% 1/10W

< SWITCH >

S501 1-786-763-11 SWITCH, TACTILE (EJECT)S502 1-786-763-11 SWITCH, TACTILE (EJECT)S503 1-786-763-11 SWITCH, TACTILE (OFF)S504 1-786-763-11 SWITCH, TACTILE (SOURCE)S505 1-786-763-11 SWITCH, TACTILE (MODE)

S506 1-786-763-11 SWITCH, TACTILE (SEL)S507 1-786-763-11 SWITCH, TACTILE (VOL +)S508 1-786-763-11 SWITCH, TACTILE (VOL )S509 1-786-763-11 SWITCH, TACTILE (ATT)S510 1-786-763-11 SWITCH, TACTILE (SENS/ALBUM )

S511 1-786-763-11 SWITCH, TACTILE (1/REP)S512 1-786-763-11 SWITCH, TACTILE (2/SHUF)S513 1-786-763-11 SWITCH, TACTILE (SEEK +/> M)S514 1-786-763-11 SWITCH, TACTILE (SEEK /m .)S515 1-786-763-11 SWITCH, TACTILE (EQ3)

S516 1-786-763-11 SWITCH, TACTILE (DSPL)S517 1-786-763-11 SWITCH, TACTILE (SCRL)S518 1-786-763-11 SWITCH, TACTILE (6/PAUSE)S519 1-786-763-11 SWITCH, TACTILE (5/OSD)S520 1-786-763-11 SWITCH, TACTILE (4/AUDIO)

S521 1-786-763-11 SWITCH, TACTILE (3/SLOW)S522 1-529-566-61 SWITCH, PUSH (1 KEY) (OPEN)S523 1-786-763-11 SWITCH, TACTILE (BTM/ALBUM +)

*************************************************************

A-1096-245-A MAIN BOARD, COMPLETE(including SPEAKER BOARD)

*********************

7-621-284-40 SCREW +P 2.6X107-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT7-685-793-09 SCREW +PTT 2.6X8 (S)7-685-795-09 SCREW +PTT 2.6X12 (S)

< CAPACITOR >

C101 1-126-964-11 ELECT 10uF 20% 50VC106 1-126-965-11 ELECT 22uF 20% 50VC107 1-126-964-11 ELECT 10uF 20% 50VC109 1-104-665-11 ELECT 100uF 20% 25VC111 1-126-964-11 ELECT 10uF 20% 50V

C113 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16VC303 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC408 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V

C409 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10VC410 1-126-960-11 ELECT 1uF 20% 50VC411 1-126-960-11 ELECT 1uF 20% 50VC412 1-126-960-11 ELECT 1uF 20% 50VC413 1-126-960-11 ELECT 1uF 20% 50V

C414 1-126-964-11 ELECT 10uF 20% 50VC416 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC417 1-126-947-11 ELECT 47uF 20% 35VC420 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC421 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C422 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC423 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC424 1-126-964-11 ELECT 10uF 20% 50VC425 1-126-964-11 ELECT 10uF 20% 50VC426 1-126-964-11 ELECT 10uF 20% 50V

C428 1-126-964-11 ELECT 10uF 20% 50VC430 1-126-947-11 ELECT 47uF 20% 35VC433 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC434 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC435 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C436 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC437 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16VC438 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16VC439 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC440 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V

C441 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10VC443 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC444 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16VC446 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC447 1-126-961-11 ELECT 2.2uF 20% 50V

C450 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC451 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC452 1-126-964-11 ELECT 10uF 20% 50VC453 1-126-964-11 ELECT 10uF 20% 50VC454 1-126-964-11 ELECT 10uF 20% 50V

C612 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC614 1-115-156-11 CERAMIC CHIP 1uF 10VC618 1-126-947-11 ELECT 47uF 20% 35VC619 1-126-964-11 ELECT 10uF 20% 50VC620 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C701 1-124-584-00 ELECT 100uF 20% 10VC704 1-124-584-00 ELECT 100uF 20% 10VC705 1-124-584-00 ELECT 100uF 20% 10VC706 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC707 1-124-584-00 ELECT 100uF 20% 10V

C709 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC711 1-124-589-11 ELECT 47uF 20% 16VC807 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC809 1-104-665-11 ELECT 100uF 20% 25VC810 1-125-701-11 DOUBLE LAYERS 0.047F 5.5V

C812 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC813 1-104-665-11 ELECT 100uF 20% 25VC815 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC816 1-162-917-11 CERAMIC CHIP 15PF 5% 50VC817 1-162-917-11 CERAMIC CHIP 15PF 5% 50V

C821 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC822 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC825 1-104-665-11 ELECT 100uF 20% 25V

DISPLAY MAIN

40

CDX-V3800

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

C908 1-123-611-61 ELECT 1uF 20% 50VC922 1-131-868-81 ELECT 3300uF 20% 16VC990 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25VC991 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25VC992 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V

C993 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25VC994 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V

< CONNECTOR >

CN751 1-779-294-11 CONNECTOR, FFC (LIF(NON-ZIF)) 26PCNP800 1-794-311-21 PLUG, CONNECTOR 12PCNP901 1-774-701-21 PIN, CONNECTOR 16P

< DIODE >

D301 8-719-977-12 DIODE DTZ6.8BD400 8-719-080-34 DIODE SDS511D600 8-719-069-55 DIODE UDZSTE-175.6BD701 8-719-080-34 DIODE SDS511D702 8-719-080-34 DIODE SDS511

D801 8-719-080-34 DIODE SDS511D802 8-719-058-24 DIODE RB501V-40TE-17D808 8-719-977-12 DIODE DTZ6.8BD811 8-719-109-97 DIODE RD6.8ESB2D812 8-719-109-97 DIODE RD6.8ESB2

D813 8-719-109-97 DIODE RD6.8ESB2D814 8-719-109-97 DIODE RD6.8ESB2D815 8-719-109-97 DIODE RD6.8ESB2D816 8-719-109-97 DIODE RD6.8ESB2D817 8-719-109-97 DIODE RD6.8ESB2

D820 8-719-991-33 DIODE 1SS133T-77D823 8-719-083-66 DIODE UDZSTE-1718BD825 8-719-083-66 DIODE UDZSTE-1718BD902 8-719-053-18 DIODE 1SR154-400TE-25D903 8-719-053-18 DIODE 1SR154-400TE-25

D904 6-500-522-01 DIODE 10EDB40-TA1B2D905 6-500-522-01 DIODE 10EDB40-TA1B2D906 6-500-522-01 DIODE 10EDB40-TA1B2D907 6-500-522-01 DIODE 10EDB40-TA1B2D908 6-500-522-01 DIODE 10EDB40-TA1B2

D909 6-500-522-01 DIODE 10EDB40-TA1B2D912 8-719-083-66 DIODE UDZSTE-1718BD914 8-719-977-12 DIODE DTZ6.8BD915 8-719-056-84 DIODE UDZ-TE-17-7.5BD916 6-500-522-01 DIODE 10EDB40-TA1B2

D917 6-500-522-01 DIODE 10EDB40-TA1B2D918 8-719-987-69 DIODE DAN217D919 8-719-049-38 DIODE 1N5404TUD921 6-500-522-01 DIODE 10EDB40-TA1B2D922 6-500-522-01 DIODE 10EDB40-TA1B2

< FERRITE BEAD >

FB702 1-414-813-11 FERRITE, EMI (SMD) (2012)FB901 1-414-813-11 FERRITE, EMI (SMD) (2012)FB902 1-414-813-11 FERRITE, EMI (SMD) (2012)

< IC >

IC100 6-705-360-02 IC TDA8588BJ/N2/R1IC401 6-705-372-01 IC BD3808FS-FE2

IC801 6-805-155-01 IC MB90488BPF-G-135-BNDE1IC802 8-759-659-13 IC PST3428UL

< JUMPER RESISTOR >

JR5 1-216-864-11 SHORT CHIP 0JR6 1-216-864-11 SHORT CHIP 0JR10 1-414-227-11 INDUCTOR, FERRITE BEADJR12 1-216-864-11 SHORT CHIP 0

< COIL >

L400 1-414-398-11 INDUCTOR 10uHL602 1-414-394-41 INDUCTOR 2.2uHL700 1-410-509-11 INDUCTOR 10uHL701 1-410-501-11 INDUCTOR 2.2uHL702 1-410-509-11 INDUCTOR 10uH

L703 1-414-813-11 FERRITE, EMI (SMD) (2012)L900 1-456-617-11 COIL, CHOKE

< JACK >

PJ401 1-774-700-11 JACK, PIN 6P (AUX IN,AUDIO OUT REAR/FRONT)

PJ601 1-793-598-11 JACK (ANTENNA)

< TRANSISTOR >

Q400 8-729-038-71 TRANSISTOR KRC107SQ401 8-729-038-55 TRANSISTOR KRA103SQ402 6-551-070-01 TRANSISTOR KRC283S-B-RPK/PQ403 6-551-070-01 TRANSISTOR KRC283S-B-RPK/PQ404 6-551-070-01 TRANSISTOR KRC283S-B-RPK/P

Q405 6-551-070-01 TRANSISTOR KRC283S-B-RPK/PQ406 6-551-070-01 TRANSISTOR KRC283S-B-RPK/PQ407 6-551-070-01 TRANSISTOR KRC283S-B-RPK/PQ601 8-729-920-85 TRANSISTOR 2SD1664-QRQ701 8-729-106-60 TRANSISTOR 2SB1115A-YQ

Q703 8-729-027-46 TRANSISTOR DTC114YKA-T146Q800 8-729-038-55 TRANSISTOR KRA103SQ900 8-729-034-51 TRANSISTOR KTC3875Q902 8-729-038-67 TRANSISTOR KRC102SQ906 8-729-034-51 TRANSISTOR KTC3875

Q907 8-729-038-67 TRANSISTOR KRC102S

< RESISTOR >

R302 1-216-809-11 METAL CHIP 100 5% 1/10WR402 1-216-864-11 SHORT CHIP 0R403 1-216-864-11 SHORT CHIP 0R404 1-216-809-11 METAL CHIP 100 5% 1/10WR405 1-216-809-11 METAL CHIP 100 5% 1/10W

R406 1-216-809-11 METAL CHIP 100 5% 1/10WR407 1-216-809-11 METAL CHIP 100 5% 1/10WR408 1-216-864-11 SHORT CHIP 0R409 1-218-881-11 METAL CHIP 27K 0.5% 1/10WR411 1-216-809-11 METAL CHIP 100 5% 1/10W

R412 1-216-809-11 METAL CHIP 100 5% 1/10WR413 1-216-864-11 SHORT CHIP 0R414 1-216-809-11 METAL CHIP 100 5% 1/10WR415 1-216-809-11 METAL CHIP 100 5% 1/10WR416 1-216-809-11 METAL CHIP 100 5% 1/10W

MAIN

41

CDX-V3800

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

R417 1-216-809-11 METAL CHIP 100 5% 1/10WR418 1-216-841-11 METAL CHIP 47K 5% 1/10WR419 1-216-841-11 METAL CHIP 47K 5% 1/10WR420 1-216-841-11 METAL CHIP 47K 5% 1/10WR421 1-216-841-11 METAL CHIP 47K 5% 1/10W

R424 1-216-805-11 METAL CHIP 47 5% 1/10WR425 1-216-833-11 METAL CHIP 10K 5% 1/10WR426 1-216-824-11 METAL CHIP 1.8K 5% 1/10WR427 1-216-809-11 METAL CHIP 100 5% 1/10WR428 1-216-833-11 METAL CHIP 10K 5% 1/10W

R429 1-247-807-31 CARBON 100 5% 1/4WR430 1-216-824-11 METAL CHIP 1.8K 5% 1/10WR431 1-247-807-31 CARBON 100 5% 1/4WR432 1-216-809-11 METAL CHIP 100 5% 1/10WR435 1-216-809-11 METAL CHIP 100 5% 1/10W

R436 1-216-809-11 METAL CHIP 100 5% 1/10WR437 1-216-821-11 METAL CHIP 1K 5% 1/10WR440 1-216-809-11 METAL CHIP 100 5% 1/10WR441 1-216-809-11 METAL CHIP 100 5% 1/10WR442 1-216-841-11 METAL CHIP 47K 5% 1/10W

R443 1-216-841-11 METAL CHIP 47K 5% 1/10WR447 1-216-811-11 METAL CHIP 150 5% 1/10WR448 1-216-841-11 METAL CHIP 47K 5% 1/10WR468 1-216-789-11 METAL CHIP 2.2 5% 1/10WR603 1-247-807-31 CARBON 100 5% 1/4W

R604 1-247-807-31 CARBON 100 5% 1/4WR606 1-216-809-11 METAL CHIP 100 5% 1/10WR607 1-216-809-11 METAL CHIP 100 5% 1/10WR608 1-216-809-11 METAL CHIP 100 5% 1/10WR615 1-216-821-11 METAL CHIP 1K 5% 1/10W

R701 1-216-057-00 RES-CHIP 2.2K 5% 1/10WR702 1-216-033-00 RES-CHIP 220 5% 1/10WR703 1-216-864-11 SHORT CHIP 0R705 1-216-809-11 METAL CHIP 100 5% 1/10WR708 1-216-864-11 SHORT CHIP 0

R709 1-216-864-11 SHORT CHIP 0R800 1-216-864-11 SHORT CHIP 0R801 1-216-809-11 METAL CHIP 100 5% 1/10WR804 1-216-809-11 METAL CHIP 100 5% 1/10WR805 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R806 1-218-871-11 METAL CHIP 10K 0.5% 1/10WR809 1-216-845-11 METAL CHIP 100K 5% 1/10WR810 1-216-845-11 METAL CHIP 100K 5% 1/10WR812 1-216-845-11 METAL CHIP 100K 5% 1/10WR813 1-216-845-11 METAL CHIP 100K 5% 1/10W

R814 1-216-845-11 METAL CHIP 100K 5% 1/10WR815 1-249-435-11 CARBON 33K 5% 1/4WR816 1-216-821-11 METAL CHIP 1K 5% 1/10WR817 1-216-821-11 METAL CHIP 1K 5% 1/10WR818 1-216-809-11 METAL CHIP 100 5% 1/10W

R819 1-216-809-11 METAL CHIP 100 5% 1/10WR821 1-216-817-11 METAL CHIP 470 5% 1/10WR822 1-216-817-11 METAL CHIP 470 5% 1/10WR823 1-216-817-11 METAL CHIP 470 5% 1/10WR824 1-216-849-11 METAL CHIP 220K 5% 1/10W

R825 1-216-849-11 METAL CHIP 220K 5% 1/10WR826 1-216-843-11 METAL CHIP 68K 5% 1/10WR828 1-216-809-11 METAL CHIP 100 5% 1/10W

R830 1-216-809-11 METAL CHIP 100 5% 1/10WR832 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR833 1-249-417-11 CARBON 1K 5% 1/4WR834 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR835 1-216-845-11 METAL CHIP 100K 5% 1/10W

R836 1-216-845-11 METAL CHIP 100K 5% 1/10WR837 1-216-821-11 METAL CHIP 1K 5% 1/10WR839 1-216-809-11 METAL CHIP 100 5% 1/10WR840 1-216-809-11 METAL CHIP 100 5% 1/10WR841 1-216-809-11 METAL CHIP 100 5% 1/10W

R843 1-216-809-11 METAL CHIP 100 5% 1/10WR846 1-216-845-11 METAL CHIP 100K 5% 1/10WR847 1-216-845-11 METAL CHIP 100K 5% 1/10WR848 1-216-845-11 METAL CHIP 100K 5% 1/10WR849 1-216-841-11 METAL CHIP 47K 5% 1/10W

R850 1-218-871-11 METAL CHIP 10K 0.5% 1/10WR853 1-216-864-11 SHORT CHIP 0R854 1-216-864-11 SHORT CHIP 0R860 1-216-845-11 METAL CHIP 100K 5% 1/10WR873 1-216-845-11 METAL CHIP 100K 5% 1/10W

R901 1-216-845-11 METAL CHIP 100K 5% 1/10WR902 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR903 1-216-841-11 METAL CHIP 47K 5% 1/10WR904 1-216-841-11 METAL CHIP 47K 5% 1/10WR912 1-249-417-11 CARBON 1K 5% 1/4W

R913 1-216-821-11 METAL CHIP 1K 5% 1/10WR916 1-216-864-11 SHORT CHIP 0R917 1-249-421-11 CARBON 2.2K 5% 1/4WR925 1-216-845-11 METAL CHIP 100K 5% 1/10WR927 1-216-833-11 METAL CHIP 10K 5% 1/10W

R928 1-249-421-11 CARBON 2.2K 5% 1/4WR931 1-216-073-00 RES-CHIP 10K 5% 1/10WR932 1-216-073-00 RES-CHIP 10K 5% 1/10WR936 1-216-864-11 SHORT CHIP 0

< SWITCH >

S800 1-571-850-51 SWITCH, SLIDE (FREQUENCY SELECT)S802 1-762-638-21 SWITCH, TACTILE (RESET)

< TUNER >

TUX601 A-3220-961-A TUNER UNIT (TUX-032)

< VIBRATOR >

X800 1-813-524-21 VIBRATOR, CERAMIC (18.432MHz)X801 1-813-202-11 VIBRATOR, CRYSTAL (32.768kHz)

*************************************************************

SENSOR BOARD**************

< SWITCH >

SW2 1-529-566-61 SWITCH, PUSH (1 KEY) (SELF)SW3 1-529-566-61 SWITCH, PUSH (1 KEY) (DISC IN)

*************************************************************

MAIN SENSOR

42

CDX-V3800

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

A-1107-620-A SERVO BOARD, COMPLETE**********************

< CAPACITOR >

C102 1-104-609-11 ELECT CHIP 100uF 20% 4VC103 1-126-208-21 ELECT CHIP 47uF 20% 4VC111 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC112 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC131 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C132 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC133 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC160 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC161 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC162 1-164-378-11 CERAMIC CHIP 30PF 5% 50V

C163 1-110-563-11 CERAMIC CHIP 0.068uF 10% 16VC164 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC165 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC166 1-164-935-11 CERAMIC CHIP 470PF 10% 50VC180 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

C181 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC182 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC183 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC201 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3VC202 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C301 1-126-208-21 ELECT CHIP 47uF 20% 4VC302 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC303 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC304 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC305 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C312 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC313 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC400 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC401 1-104-609-11 ELECT CHIP 100uF 20% 4VC402 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C403 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC404 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC405 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC406 1-162-909-11 CERAMIC CHIP 4PF 0.25PF 50VC407 1-162-909-11 CERAMIC CHIP 4PF 0.25PF 50V

C410 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC501 1-104-609-11 ELECT CHIP 100uF 20% 4VC502 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC503 1-162-928-11 CERAMIC CHIP 120PF 5% 50VC504 1-162-962-11 CERAMIC CHIP 470PF 10% 50V

C505 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC506 1-104-609-11 ELECT CHIP 100uF 20% 4VC507 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC508 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC509 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V

C510 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC511 1-126-602-11 ELECT CHIP 3.3uF 20% 50VC512 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16VC513 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC514 1-100-381-11 ELECT CHIP 10uF 20% 16V

C515 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC516 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC517 1-104-609-11 ELECT CHIP 100uF 20% 4VC518 1-104-609-11 ELECT CHIP 100uF 20% 4V

C519 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC521 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC531 1-126-208-21 ELECT CHIP 47uF 20% 4VC540 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC541 1-164-217-11 CERAMIC CHIP 150PF 5% 50V

C542 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50VC543 1-164-217-11 CERAMIC CHIP 150PF 5% 50VC544 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3VC545 1-162-921-11 CERAMIC CHIP 33PF 5% 50VC546 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V

C547 1-164-854-11 CERAMIC CHIP 15PF 5% 50VC548 1-164-854-11 CERAMIC CHIP 15PF 5% 50VC551 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC600 1-128-995-21 ELECT CHIP 100uF 20% 10VC605 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C705 1-126-208-21 ELECT CHIP 47uF 20% 4VC706 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC707 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC708 1-126-208-21 ELECT CHIP 47uF 20% 4VC709 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

< CONNECTOR >

CN1 1-784-876-21 CONNECTOR, FFC (LIF(NON-ZIF)) 26P* CN401 1-695-320-21 PIN, CONNECTOR (1.5mm) (SMD) 2P

CN500 1-815-016-21 CONNECTOR, FFC/FPC (ZIF) 16P

< DIODE >

D101 8-719-053-18 DIODE 1SR154-400TE-25D906 6-500-812-01 DIODE RLZTE-113.6BD907 8-719-083-57 DIODE UDZSTE-173.6BD909 8-719-083-57 DIODE UDZSTE-173.6BD910 8-719-083-57 DIODE UDZSTE-173.6B

< FERRITE BEAD >

FB501 1-216-864-11 SHORT CHIP 0FB502 1-414-595-11 INDUCTOR, FERRITE BEADFB503 1-469-777-21 INDUCTOR, FERRITE BEADFB504 1-216-864-11 SHORT CHIP 0

< IC >

IC100 6-706-599-01 IC SPCA716A-HL111IC200 6-805-375-01 IC M29W400DB55N6E-V200IC300 6-705-992-11 IC HY57V161610ETP-7DRIC400 6-706-600-01 IC SPCA717A-HL211IC500 6-706-601-01 IC BU9536KS2

IC600 6-705-002-01 IC BA5966FP-FE2IC700 6-707-146-01 IC WM8726GED/R

< COIL >

L401 1-414-404-41 INDUCTOR 100uH

< TRANSISTOR >

Q501 8-729-904-87 TRANSISTOR 2SB1197K-RQ502 8-729-928-90 TRANSISTOR DTC114EE

< RESISTOR >

R101 1-218-933-11 RES-CHIP 22 5% 1/16WR102 1-218-933-11 RES-CHIP 22 5% 1/16W

SERVO

43

CDX-V3800

R103 1-218-933-11 RES-CHIP 22 5% 1/16WR104 1-218-933-11 RES-CHIP 22 5% 1/16WR105 1-218-933-11 RES-CHIP 22 5% 1/16WR106 1-218-941-81 RES-CHIP 100 5% 1/16WR107 1-218-941-81 RES-CHIP 100 5% 1/16W

R108 1-218-941-81 RES-CHIP 100 5% 1/16WR109 1-218-933-11 RES-CHIP 22 5% 1/16WR110 1-218-933-11 RES-CHIP 22 5% 1/16WR111 1-218-933-11 RES-CHIP 22 5% 1/16WR112 1-218-933-11 RES-CHIP 22 5% 1/16W

R113 1-218-933-11 RES-CHIP 22 5% 1/16WR114 1-218-933-11 RES-CHIP 22 5% 1/16WR161 1-218-941-81 RES-CHIP 100 5% 1/16WR162 1-218-941-81 RES-CHIP 100 5% 1/16WR163 1-218-935-11 RES-CHIP 33 5% 1/16W

R164 1-220-199-81 RES-CHIP 24K 5% 1/16WR165 1-218-935-11 RES-CHIP 33 5% 1/16WR166 1-218-941-81 RES-CHIP 100 5% 1/16WR167 1-218-973-11 RES-CHIP 47K 5% 1/16WR168 1-218-941-81 RES-CHIP 100 5% 1/16W

R169 1-218-973-11 RES-CHIP 47K 5% 1/16WR170 1-218-941-81 RES-CHIP 100 5% 1/16WR171 1-218-973-11 RES-CHIP 47K 5% 1/16WR172 1-218-941-81 RES-CHIP 100 5% 1/16WR173 1-218-973-11 RES-CHIP 47K 5% 1/16W

R175 1-218-973-11 RES-CHIP 47K 5% 1/16WR176 1-218-945-11 RES-CHIP 220 5% 1/16WR177 1-218-973-11 RES-CHIP 47K 5% 1/16WR178 1-218-945-11 RES-CHIP 220 5% 1/16WR180 1-218-953-11 RES-CHIP 1K 5% 1/16W

R181 1-218-973-11 R