VOL 12.1

PRODUCTS AND SERVICES GUIDEENVIRONMENTAL MONITORING • NON-DESTRUCTIVE TESTING

REMOTE VISUAL INSPECTION • CEMS & SPECIALTY GAS

Call Today!800-242-3910

© 2

011,

Cas

ella

USA

, All

right

s re

serv

ed.

CASELLA BRAND SAMPLE PUMPS Intrinsically Safe

REAL TIME PARTICULATES Multi-Range Available

HEAT STRESS MONITOR Hand-Held WBGT

DATA MANAGEMENT SOFTWARE

CEL BRAND SOUND LEVEL METERS Octave & 1/3 Octave

NOISE DOSIMETERS Miniature Shoulder-Worn

CONSIDER casellausa.com800.366.2966

A Subsidiary of IDEAL INDUSTRIES, INC.

“Casella delivers easy to use instruments with exceptional

service... we should give them a call”

CEL

CORPORATE HEADQUARTERS 10635 Richmond Ave., Suite 100 Houston, TX 77042 Phone 832 308 7600Fax 713 339 1823

UNITED STATES / CANADA

10201 McKalla Place, Suite EAustin, TX 78758 Phone 800 242 3910

14141 Airline Highway Oak Alley Bldg. #4, Suites P/Q Baton Rouge, LA 70817 Phone 225 610 1270 Fax 225 610 1271

If you would like more information on the product lines or services Ashtead Technology offers in addition to what you see in this catalog, please contact any of our offices listed below or visit our website at www.ashtead-technology.com.

3528-78 Avenue NW Edmonton, Alberta T6B 2X9 Phone 780 643 2680 Fax 780 468 3050

1450 Elmhurst Rd. Elk Grove Village, IL 60007 Phone 847 718 1246 Fax 847 718 1423

CEMs / Specialty Gases1474 Elmhurst Rd. Elk Grove Village, IL 60007 Toll Free 877 GAS RENT Phone 847 631 0002 Fax 847 758 2089

883 Airport Park Rd., Suite D Glen Burnie, MD 21061 Phone 410 766 2874Fax 410 766 2919

23575 Cabot Blvd., Suite 203 Hayward, CA 94545 Phone 510 732 6591 Fax 510 732 6595

10635 Richmond Ave., Suite 100 Houston, TX 77042 Phone 713 331 3924 Fax 713 331 3934

Park 100, 7144 Zionsville Rd., Bldg. 106 Indianapolis, IN 46268 Phone 317 238 3441 Fax 317 388 1124

18195 McDurmott E., Suites A/B Irvine, CA 92614 Phone 949 955 3930 Fax 949 955 3932

1016 West Eight Ave., Suite C King of Prussia, PA 19406 Phone 484 690 1001 Fax 484 690 1002

1395 S. Marietta Parkway Bldg. 100, Suite 122 Marietta, GA 30067 Phone 770 427 8533 Fax 770 427 8558

3505 Laird Rd., Unit 18 Mississauga, Ontario L5L 5Y7 Phone 905 607 9639 Fax 905 607 8592

3311 Preston Rd. Pasadena, TX 77505 Phone 281 991 1448 Fax 281 991 1449

1057 East Henrietta Rd. Rochester, NY 14623 Phone 585 424 2140 Fax 585 424 2166

2627 Metro Blvd. St. Louis, MO 63043 Phone 314 344 1079 Fax 314 344 5074

New locations are coming soon! Please check our website for more information.

www.ashtead-technology.com

WHO WE ARE With offices spanning the globe, Ashtead Technology is one of the world’s leading providers of specialty inspection, testing and monitoring instrumentation. Our customers are found in industries as diverse as construction, power, manufacturing, survey, geotechnical, oil and gas and telecommunications, which means that we are accustomed to meeting tight deadlines and providing unique solutions to daily challenges.

As you will find in this Products and Services Guide, we specialize in Environmental Monitoring, Non-Destructive Testing (NDT), Remote Visual Inspection (RVI) and CEMS and Specialty Gas. We dedicate all of our resources to staying ahead of the ever advancing technologies these fields require for testing, sampling, monitoring, detecting or analyzing.

In June 2008 the management team, with backing from Phoenix Equity Partners (based London) successfully acquired the business in a management buyout from Ashtead Group plc., making Ashtead Technology a truly independent company. The Group is totally focused and committed to putting technical equipment into the hands of those who need it, either through short, medium or long term rental, as well as alternative financial offerings, including innovative programs such as our Rent To Own (RTO) and Perpetual Rental Program (PRP).

Throughout our development, we have invested heavily in our equipment – keeping the fleet up-to-date, in top condition and always ensuring that we have what you need available at short notice. Our commitment to the customer is simple – we provide technical advice on what to rent and how to use it; our availability of equipment is second to none and all our equipment is tested and ready for use.

800-242-3910

THE ADVANTAGE OF RENTINGRenting is the most cost-effective way to utilize a piece of equipment without incurring all of the expenses associated with ownership, allowing your financial resources to be dedicated to your company’s core activities. Projects, deadlines and your requirements change, so it’s important to have all of the required equipment at hand. More and more organizations are switching to renting because of the economical advantages and convenience.

ASHTEAD TECHNOLOGY’S PERPETUAL RENTAL PROGRAMOur Perpetual Rental Program takes the benefits of renting even further by completely eliminating the return process. What is even better, this plan comes at a fraction of our standard monthly rate and still gives you continued access to our 24/7 technical support. Our PRP allows you to have all of the benefits of ownership and all of the advantages of renting.

RENT-TO-OWN AND SALESAshtead Technology now offers the option of rent-to-own as well as new and used equipment sales. Call us now to speak with a customer service representative about your equipment needs or visit our website for an updated list of instruments for sale.

REPAIR AND CALIBRATION SERVICEIn order for your equipment to function properly it requires routine calibration and maintenance. This process often requires your instrument to be sent back to the manufacturer, which can be expensive and cause you to be without your equipment for extended periods of time. Time you may not have. Let Ashtead Technology perform this service for you! Our factory trained technicians can diagnose and repair your equipment at our ISO: 9001 certified facility.

800-242-3910

2 Ambient Air Monitoring

3 Cleanroom Performance Testing

5 Confined Space Entry

8 Global Positioning

9 Hazardous Waste Investigation

11 HVAC Instruments

14 Indoor Air Quality

21 Industrial Hygiene

27 Positive Material Identification (PMI)

28 Sound, Noise & Vibration Monitoring

31 Toxic Gas Monitoring

36 Underground Location

37 Water Monitoring Instruments

43 Water Quality Instruments

44 Specialty Instruments

VTABLE OF CONTENTS

ENVIRONMENTAL MONITORING NON-DESTRUCTIVE TESTING

REMOTE VISUAL INSPECTION

CEMS

68 Videoprobes

69 Thermal Cameras

70 Pipe Inspection Cameras/Tractors

74 High Speed Video Cameras & RVI Accessories

48 Coating Inspection/Ultrasonic Thickness

50 Ultrasonic Flaw Detectors

55 ACFM

56 Eddy Current

58 Ground Penetrating Radar

59 Concrete Testing

60 Positive Material Identification (PMI)

62 Tank Inspection

63 Hardness Testers

65 Specialty Instruments

76 EPA Protocol Gases

78 Ambient Air Analyzers

81 EPA Source Analyzers NO/NO2/NOX

82 EPA Source Analyzers NO/NO2/NOX/O2/CO

83 EPA Source Analyzers NOX/SO2/CO/CO2/O2

84 EPA Source Analyzers O2/CO2

85 Total Hydrocarbon Analyzers (FID)

88 Combustion Analyzers

89 Probes, Conditioning Equipment & Accessories

APPENDIXi Metric Conversions

ii SapphIRe Library

v INNOV-X Library

vii Niton Library

x Niton XLt 898 Library

xi Glossary

xxi Category Index

xxiii Product Index Don’t miss our list of consumables on the last page of the catalog.

CEMS75

Our Continuous Emission Monitoring (CEMs) facility is manned by a highly-skilled team of technicians, with more than 20 years of combined experience working within the CEMs industry. In addition to rentals, repair service and calibration as well as technical support and complete turn key solutions are all available.

CEMS & SPECIALTY GAS

To compliment our wide selection of emissions monitoring and ambient air instrumentation, Ashtead Technology has partnered with Airgas to offer EPA Protocol and other emission monitoring gases that can be used for engineering studies and non-compliance audits. Examples include: propane, methane, carbon monoxide, nitrogen dioxide, sulfur dioxide, hydrogen chloride, oxygen, percent level gases and more.

In line with the company’s policy to deliver market leading rental instrumentation that is tested, calibrated and in perfect working condition every time, Ashtead Technology has developed a testing facility to ensure accuracy in Protocol gas handling and air emission monitoring equipment that we supply to stack testing professionals all over the United States.

800-242-3910

CEMS 76EPA PROTOCOL GASES

Ashtead Technology offers certified calibration gases that can be used for engineering studies and non-compliance audits. Examples include: Propane, Methane, Carbon Monoxide, Nitrogen Dioxide, Sulfur Dioxide, Hydrogen Chloride and Oxygen. Percent level gases available upon request. Ashtead Technology also has a large selection of pure gases for specific industry process applications. In addition to our pure gases, Ashtead Technology carries certified Zero gases and FID fuel blends available for next day shipping. Call today to find out more!

PROTOCOL PROPANE (C4H6)

Protocol Propane Gases in balance air are available in span ranges from 0-10 ppm up to 10% (100,000 ppm). Propane standards are used to calibrate FID instruments designed to measure Total Hydrocarbon Emission for compliance reporting. Applicable EPA methods: USEPA Method 25A & CFR 40 Part 60 Performance Specification 8A.

PROTOCOL METHANE (CH4) Protocol Methane Gases in balance air are available in span ranges from 0-10 ppm up to 10% (100,000 ppm). Methane standards are used to calibrate FID instruments and for determining total gaseous non-methane organics for compliance reporting. Applicable EPA methods: USEPA Method 25A & CFR 40 Part 60 Performance Specification 8A.

PROTOCOL CARBON MONOXIDE (CO)

Protocol Carbon Monoxide Gases in balance Nitrogen are available in span ranges from 0-10 ppm up to 10% (100,000 ppm). Carbon Monoxide standards are used to calibrate Continuous Emission Monitors designed to measure CO for compliance reporting. Applicable EPA methods: USEPA Method 10 & CFR 40 Part 60 Performance Specification 4.

PROTOCOL CARBON DIOXIDE (CO2) Protocol Carbon Dioxide Gases are available in span ranges from 0-25%. Carbon Dioxide standards are used to calibrate Continuous Emission Monitors designed to measure CO2 for compliance reporting. Applicable EPA methods: USEPA Method 3, CFR 40 Part 60 Performance Specification 3 & CFR 40 Part 75.

PROTOCOL OXYGEN (O2) Protocol Oxygen Gases are available in span ranges from 0-25%. Oxygen standards are used to calibrate Continuous Emission Monitors designed to measure O2 for compliance reporting. Applicable EPA methods: USEPA Method 3 & CFR 40 Part 60 Performance Specification 3.

PROTOCOL NITRIC OXIDE (NO) Protocol Nitric Oxide Gases in balance Nitrogen are available in span ranges from 0-10 ppm up to 1% (10,000 ppm). Nitric Oxide standards are used to calibrate Continuous Emission Monitors designed to measure NOx for compliance reporting. Applicable EPA methods: USEPA Method 7E, CFR 40 Part 60 Performance Specification 2 & CFR 40 Part 75.

PROTOCOL SULFUR DIOXIDE (SO2)

Protocol Sulfur Dioxide Gases in balance Nitrogen are available in span ranges from 0-50 ppm up to 1% (10,000 ppm). Sulfur Dioxide standards are used to calibrate Continuous Emission Monitors designed to measure SO2 for compliance reporting. Applicable EPA methods: USEPA Method 6C, CFR 40 Part 60 Performance Specification 2 & CFR 40 Part 75.

PROTOCOL HYDROGEN CHLORIDE (HCL) Protocol Hydrogen Chloride Gases in balance Nitrogen are available in span ranges from 0-50 ppm up to .5% (5,000 ppm). Hydrogen Chloride standards are used to calibrate instruments designed to measure HCL for compliance reporting. Applicable EPA methods: USEPA Method 321.

cai_ad_8.375x5.375_ashtead_Layout 1 8/22/11 4:13 PM Page 1

800-242-3910

CEMS 78

NO/NO2/NOX Analyzers • Thermo 42c • Teledyne API 200A The NO/ NO2/NOX analyzers from Thermo and Teledyne utilize the chemiluminescence method to provide sensitive and accurate measurements for ambient monitoring.The Thermo 42c includes a user-friendly interface and extended troubleshooting diagnostics to provide instantaneous indication of instrument operating status. The Teledyne API 200A features built-in data logging and continuous auto-zero to eliminate drift. Measurements are automatically compensated for temperature, pressure and flow rate. The Thermo 42i is also available upon request.

THERMO 42C TELEDYNE API 200A

Ranges Detection Limit 0 to 1000ppb; 0.4ppb 0 to 100ppm; user selectable 0 to 50ppb; 0.4ppb 0 to 20,000ppb full scale; user selectable independent NO, NO2, NOXranges; auto-ranging supported

AMBIENT AIR ANALYZERS

Thermo 42c NO/NO2/NOX Analyzer

Thermo 49i O3 Analyzers The 49i ozone analyzer from Thermo uses the UV photometric method to allow users to assure worker safety in environments where ozone is suspected. This instrument meets EPA standards.The Thermo 49i features an Ethernet port as well as flash memory for increased data storage and field upgrades. Users can set alarm levels for concentration and for a wide variety of internal diagnostics. Dual range and auto range are standard features, as is temperature and pressure correction. Because the instrument has both sample and reference flowing at the same time, a response time of 20 seconds can be achieved.

THERMO 49i

Ranges Detection Limit 0-0.5 to 200ppm; 0.5ppb 0-0.1 to 400mg/m3; user selectable

Thermo 49i O3 Analyzer

www.ashtead-technology.com

CEMS79

Thermo 43i SO2 Analyzer

SO2 Analyzers • Thermo 43i• Teledyne API 100AH/EH The sulfur dioxide analyzers from Thermo and Teledyne use the UV fluorescence principle to detect low levels of sulfur dioxide. The Thermo 43i utilizes reflective bandpass filters which are less subject to photochemical degradation and more selective in wavelength isolation. This unit features an Ethernet port as well as flash memory. The Teledyne API 100AH/EH uses microprocessor technology to gather and store accurate measurements. A hydrocarbon “kicker” and advanced optical design prevent inaccuracies due to interference.

THERMO 43i TELEDYNE API 100A

Ranges Detection Limit 0-0.05 to 10ppm; 0.5ppb 0 to 50ppb; 0.4ppb 0 to 20,000ppb full scale user selectable; dual ranges and auto ranging supported

AMBIENT AIR ANALYZERS

Teledyne API 300E CO Analyzer

Teledyne API 300E CO Analyzer • Gas filter correlation• EPA approval RCFA 1093-99• Built-in data acquisition allows the logging

of multiple parameters

Ranges Zero Noise Span Noise Lower Detectable Limit Zero Drift Span Drift Precision Datalogging Serial Output

0 to 1, to 0 to 1000ppm CO Full scale, user selectable. Dual ranges and auto ranging supported <0.02ppm <0.5% of reading above 5ppm 0.04ppm <0.1ppm/24 hours, <0.2ppm/7 days <1%/7 days 0.5% of reading Up to 8000 records, date and time stamped RS-232 port

800-242-3910

CEMS 80

Thermo 450i H2S/SO2 Analyzer • Pulsed fluorescent technology is used to detect SO2

molecules formed by catalytic conversion of H2S• Simultaneous measurement readings of H2S and

SO2 provide reliable data capture on a constant basis

• Reflective bandpass filters are more selective in wavelength isolation, minimizing photochemical degradation

Ranges Zero Drift Span Drift Sample Flow Rate Precision

0-0.05 to 100ppm Less than 1ppb ±1% full scale 1.0 liter/min. 1% of reading or 1ppb (whichever is greater)

AMBIENT AIR ANALYZERS

Thermo 450i H2S/SO2 Analyzer

California Analytical 602D CO2 PPM Analyzer

California Analytical 602D CO2 PPM Analyzer • Based on the infrared absorption characteristics of

gases by using a single infrared beam to measure gas concentrations

• Features dual IR detectors for two simultaneous sample screens

• Temperature and pressure compensation• Ideal for combustion efficiency monitoring, process

chemical gas analysis, personal safety and vehicle emission studies

Ranges 0 to 1000, 2000, 3000ppm, user selectable

Call 800-242-3910 to request a rate schedule for any equipment seen in this catalog!Want to

know more?

www.ashtead-technology.com

CEMS81

Thermo 42iHL NO/NO2/NOX Analyzer

Thermo 42iHL and 42CHL NO/NO2/NOX Analyzers • Measures the amount of nitrogen oxides in the air

from sub-ppm levels up to 100ppm• Single chamber, single photomultiplier tube design

that cycles between the NO, NOX modes• Independent outputs for NO, NO2 and NOX (each

can also be calibrated separately)• User Defined Ranges 0-10ppm to 5000ppm • Auto Ranging• EPA Compliant

Detection Method Range Detection Limit Selectable Outputs

Chemiluminescence 0 to 10ppm up to 5000ppm 50ppb 0-10 MV; 0-100 mV; 1 V; 5 V; 10 V voltage outputs, user selectable and RS 232 communication port

EPA SOURCE ANALYZERS

Thermo 42i-LS Low Source NO-NO2-NOx Analyzer

Thermo 42i-LS Low Source NO/NO2/NOX Analyzers • Measures the amount of nitrogen oxides in the air

from sub-ppb levels up to 500ppm• Single chamber, single photomultiplier tube design

that cycles between the NO and NOx modes• Independent outputs for NO, NO2 and NOx (each

can be calibrated separately)• Auto Ranging• EPA Compliant

Detection Method

Ranges

Detection Limit Zero Drift Span Drift Flowrate

Chemiluminescence

0-0.5ppm to 0-500ppm or 0-2mg/m3 to 0-750 mg/m3

±0.01ppm ±0.005ppm ±1% full scale

Approx. 110 cc/min.

800-242-3910

CEMS 82

NO/NO2/NOX Analyzers • Teledyne API 200AH/EH • CAI 650 CLD

The Teledyne API 200AH/EH High Range NO/NO2/NOX analyzer uses the field-proven chemiluminescent technique for monitoring high levels of oxides of nitrogen. User-selectable ranges of 5 ppm to 5000 ppm make it ideal for a wide variety of applications including CEM, stack testing, and process control. The CAI 650 CLD analyzer is designed around a state-of-the-art 16 bit microprocessor, with 16 digital inputs, 16 digital outputs, 16 analog inputs and 4 analog outputs. It is ideal for a wide variety of applications including CEM, combustion efficiency, power plant de-nitrification, and fuel cell analysis. The CAI 650 also measures O2

Detection Method Selectable Ranges Teledyne API 200

CAI 650 Selectable Outputs Teledyne API 200

CAI 650

Chemiluminescence

0 to5ppm; 0 to 5,000ppm full scale; user selectable; Independent NO, NO2, NOX ranges; auto-ranging supported

0 to3ppm; 0 to 3,000ppm NO/NOx (Other Ranges Available) 4 user selectable ranges.0 to 25% for 02

0-1 V; 5 V; 10 V, 0 - 100mV, Bipolar

0-1 V; 5 V; 10 V, 0 - 100mV, Selectable

EPA SOURCE ANALYZERS

Thermo API 200AH High Range NO/NO2/NOX Analyzer

CO Analyzers • Thermo 48C• Thermo 48CHL• California Analytical (Fuji) 3300 The carbon monoxide analyzers from Thermo and California Analytical are ideal for CO detection applications such as monitoring gasoline or diesel vehicles. These instruments utilize the non dispersive infrared (NDIR) method.

THERMO 48C THERMO 48C-HL CALIFORNIA ANALYTICAL (FUJI) 3300

Ranges Detection Limit 0-1ppm to 10,000ppm; 0.04ppm user selectable 0-50ppm to 20,000ppm; 4.0ppm user selectable 0-2%; 0-5%; 1% of scale user selectable

CAI 650 CLD NO/NO2/NOX /O2 Analyzer

www.ashtead-technology.com

CEMS83

Ametek/Western Research 921M

SO2 Analyzers • Ametek/Western Research 921M/9000 Series• Teledyne API 100AH The Ametek 921M/9000 Series utilizes the dual wavelength/nondispersive UV methods to perform simultaneous dual range analysis on a continuous basis. It has a sealed gas reference cell for increased stability and accuracy.The Teledyne API 100AH uses UV fluorescence technology to offer the highest measurement range and interferent rejection required for extractive source sampling. Special optical filtering reduces the effects of NO interference. This unit features built in data acquisition for logging of multiple parameters.

EPA SOURCE ANALYZERS

AMETEK 921M

TELEDYNE API 100AH

Ranges Detection Limit 0-100 to 0-5000ppm 0.25ppm full scale; user selectable

0-10 to 0-5000ppm 0.1ppm full scale; user selectable; dual ranges and auto ranging supported

Horiba PG250 Gas Analyzer Multi Component CEM

Horiba PG250 Gas Analyzer Multi Component CEM • Portable and MCERTS approved• Capable of measuring five components:

NOX, SO2, CO, CO2 and O2

Detection Methods NOX CO, SO2, CO2 O2 Ranges O2 CO NOX CO2 SO2 Selectable Outputs

Chemiluminescence NDIR Galvanic Fuel Cell 0-5, 10%, 25% 0-200 to 5000ppm 0-25ppm to 0-2500ppm 0-5%, 10%, 20% 0-200ppm to 3000ppm RS-232 port, 4-20mA,0 - 1 Volts

800-242-3910

CEMS 84

MKS MultiGas 2030 FTIR Continuous Gas Analyzer

An FTIR based gas analyzer capable of percent level detection as well as ppb sensitivity for multiple gas species in a variety of applications. Capability of simultaneously analyzing and displaying more than 30 gases.

EPA SOURCE ANALYZERS

Servomex 1400 Series O2 and CO2 Analyzer

MKS MultiGas 2030 FTIR Continuous Gas Analyzer

Servomex 1400 Series O2 and CO2 Analyzers • 1420C O2 Analyzer• 1415C CO2 Analyzer The 1400 STD series analyzers from Servomex are available for non-flammable, non-toxic gases. The STD version analyzers are comprised of one or two measurement modules, a low flow alarm and an Automatic Flow Control Device (AFCD) to control the sample flow through the analyzer.

1420C O2 1415C CO2

Detection Ranges Detection Method Limit Paramagnetic 0 to 25%; 0.1% Cell 0 to 100% IR 0 to 20%; 1% of scale 0 to 25%

Applications

Ranges Spectral Resolution

Scan Time

Scan Speed

Gases and Vapors Measurable

Automobile, stack monitoring, process monitoring, development and optimization, Ambient air analysis (industrial hygiene), bulk gas purity analysis, contamination in CO2 Sequestration, SCR performance monitoring

Concentration setting between 10ppb and 100% full scale, depending on the application

0.5-128cm-1

1-300 sec

1 scan/sec @ 0.5cm-1

Most molecules except for N2, H2, and O2

www.ashtead-technology.com

CEMS85

J.U.M. 3-500 FID THC Analyzer

J.U.M. 3-300 and 3-500FID THC Analyzers • Uses a hydrogen flame ionization detector (FID) in a

heated oven to provide highly reliable performance• Applicable in the analysis of trace level

contaminants in high purity gases or air• Built in burner air supply so no extra bottles for

burner air are needed

Detection Method Ranges Detection Limit Selectable Outputs Fuel Requirements

Flame Ionization (FID) 0 to 10ppm; up to 100,000ppm 1.0ppm CH4 0 to 10V; 4 to 20mA 100% hydrogen; optional 60/40 blend

TOTAL HYDROCARBON ANALYZERS (FID)

VIG 20 Single Channel Heated FID THC Analyzer

VIG 20 Single Channel and 20/2 Dual Channel Heated FID THC Analyzers • VIG 20 Single Channel FID• VIG 20/2 Dual Channel FID The 20 and 20/2 are microprocessor based, oven heated total hydrocarbon (THC) analyzers. The VIG 20 is designed to continuously measure one sample stream and the VIG 20/2 is a dual FID which can measure two sample streams simultaneously. The flame ionization detectors, sample filters, all sample lines, solenoid valves, pump heads, capillaries, and other components that come in contact with the samples are maintained in a temperature-controlled heated oven to prevent condensation, and to provide repeatable, reliable performance in the analysis of a wide varieties of hydrocarbon concentrations in gaseous mixtures or in ambient air.Specs shown below are identical for both models.

Ranges Detection Limit Fuel Requirements

0 to 100ppm; up to 100,000ppm; user selectable 1.0% of full scale 100% hydrogen (combustion air required)

800-242-3910

CEMS 86

J.U.M. 109L

The J.U.M. Engineering 109L non-methane hydrocarbon (NMHC) analyzer is a compact analysis system using the FID (Flame Ionization Detector) principle. There is no additional sample handling equipment required and It features a dual detector/dual electrometer design which provides three continuous, simultaneous signals of: total hydrocarbons, methane/only and total hydrocarbons less methane.

TOTAL HYDROCARBON ANALYZERS (FID)

J.U.M. 109L FID Methane/Non-Methane THC Analyzer

CAI 600 Series M HFID

The CAI Model 600M HFID Analyzer is designed to continuously measure the total concentration of hydrocarbons or methane within a gaseous sample. The analyzers exhibit superior sensitivity and response time. The gaseous sample can be exhaust gases from an internal combustion engine, a combustion process or VOC abatement systems. This instrument can measure THC or CH4 in the ppm or percent levels. All internal components are maintained at the oven set temperature preventing condensation. Options for Internal Heated Sample Pump and Internal Zero/Span Solenoid Values are available.

Ranges

Detection Limit

0 to 500, 1000, 2000, or 5000 ppm user selectable

0.0500ppm CH4; 0.050 NMHCApplications

THC Ranges

Response Time Resolution Detection Limit

EPA Method compliance monitoring, stack gases, VOC abatement, fermentation monitoring, vehicle emissions, carbon bed breakthrough detection, personal safety

Four user definable ranges from 0-3 ppm to 0-30,000 ppm

90% Full Scale in 1.5 seconds

10 ppb CAI 600M HFID Total Hydrocarbon/Methane/Non-Methane Hydrocarbon Analyzer

www.ashtead-technology.com

CEMS87 TOTAL HYDROCARBON ANALYZERS (FID)

VIG Heated FID Model 210 Total Hydrocarbon/Methane/Ethane

VIG Heated FID Model 210 Total Hydrocarbon/Methane/Ethane • Microprocessor based, oven-heated, dual

channel FID• GC Column used for Methane & Ethane separation• Features djustable alarm and oven settings and

built in internal combustion air pump• EPA Compliant for Method 25A & Method 18

Ranges Detection Limit Response Time

0 to 10, 100, 1000, 10000 or 100000ppm LDL 0.1ppm • Total Hydrocarbons: Within 5 seconds to 90% of final reading (continuous real- time reading) • Methane: Approximately 40 seconds, updated every 3 minutes • Ethane: Approximately 55 seconds, updated every 3 minutes • Non methane: Approximately 90 seconds, updated every 3 minutes

Thermo 55i /C

The Thermo 55i direct methane, non-methane hydrocarbon analyzer is configured for continuous, fully automated operation using the back-flush gas chromatography (GC) system. The GC allows for reliable measurement at sub-ppm concentrations, even in the presence of much higher methane concentrations.

Ranges Detection Limit

0 to10, 100, 1.000, 10.000, 100.000ppm, user selectable 0.1ppm CH4

Thermo 55i

800-242-3910

CEMS 88

ECOM J2KN Portable Combustion Analzyer The ECOM J2KN features wireless remote control which is ideal for combustion controls located away from the flue test port on large combustion systems. This unit features zoom display and plug-in memory up to 256MB. The J2KN can be fitted with up to 5 gas sensors to measure O2, CO, NO, NO2, SO2, and Combustibles, along with gas and ambient temperatures, stack draft & pressure, plus calculations of CO2, efficiency, excess air, and oxygen correction to 20%. Standard J2KN features include high flow pump with flowmeter, integral impact printer, and thermo-electric gas cooler with automatic condensate drain. The J2KN also offers wireless transmission of real time data via remote receiver connected to your laptop PC using ECOM’s Advanced DAS & VETS software programs. Available with optional THC sensor.

Ranges O2: 0.0 to 21.0% CO: 0 to 40,000ppm CO2: Calculated value NOX: 0 to 4000ppm NO2: 0 to 500ppm SO2: 0 to 4000ppm

Portable Emission Analyzers • ECOM AC• Testo 350XL The ECOM AC is a popular system for maintenance and trouble shooting of commercial and industrial combustion systems. The AC features an internal pump sampling line probe with thermocouple, smoke testing capability, an on board flow meter and a built in printer. The Testo 350XL features sample conditioning technology, electrochemical sensors and is ideal for short term industrial stack gas monitoring and combustion analysis. This unit features built in printing and a complete Peltier gas preparation unit for controlled condensate removal.

ECOM AC TESTO 350XL

O2: 0.0 to 21.0% CO: 0 to 40,000ppm CO2: Calculated value NOX: 0 to 4000ppm NO2: 0 to 500ppm SO2: 0 to 5000ppm

O2: 0.0 to 25% CO: 0 to 10,000ppm CO2: Calculated value NOX: 0 to 3000ppm NO2: 0 to 500ppm SO2: 0 to 5000ppm

COMBUSTION ANALYZERS

ECOM J2KN Portable Combustion Analyzer

Testo 350XL Portable Emission Analyzer

www.ashtead-technology.com

CEMS89

PM 2.5/10 Cyclone Kit with Nozzles RM201A

Thermo EPM 300 Series Dilution Probe • Designed for wet basis measurement using dilution

extractive technology• The critical functions performed prepare the

sample from the stack so that it can be accurately and precisely measured by the analyzer

• Processed samples can be transported to the analyzer up to 300 feet via an unheated sample line

• Easy in-situ calibration of total dilution system

PROBES, CONDITIONING SYSTEMS & ACCESSORIES

PM 2.5/10 Cyclone Kit with Nozzles RM201A • PM10/PM2.5 Method applies to in-stack

measurement of particulate matter equal to or less than an aerodynamic diameter of nominally 10 (PM10) and 2.5 (PM2.5 ) microns from stationary sources

• Sampling train and operation is identical to Method 201A except that PM2.5 cyclone is inserted between the PM cyclone and the filter.

• PM10 cyclone collects particulate matter greater than PM10 while PM2.5 collects PM less than PM10 and greater than PM2.5.

• In-line filter collects PM less than PM2.5. • Depends on O ring used: Viton up to 425°F, Stainless

Steel up to 1300°FHeated Sample Line • Ideal for preventing below dew point temperature

in stack gas sampling• Maintains minimum operating temperature of

300ºF in any weather conditions• Supplied in 10’, 25’, 50’ and 100’ lengths • Operates on standard 115V power

Technical Heated Sample Line

800-242-3910

CEMS 90

Universal Analyzer 3050/3080/514 Sample Cooler • Utilizes the “Peltier Effect”: Heat transfer blocks cool

by thermoelectric elements• Efficiently removes water content

Sample Flow Rate Stainless Steel Heat Exchange Kynar/Glass Heat Exchange

0 to 8L/M (at STP) 700ºF (371ºC) 280ºF (138ºC)

PROBES, CONDITIONING SYSTEMS & ACCESSORIES

Universal Analyzer 3050 Sample Cooler

PermaPure Mini-GASS Dryer System

PermaPure Mini-GASS Dryer System • Portable sampling system designed for stack

testing and intermittent use• Removes water, acid mists and particulates without

effecting sample gas• 0.1 micron coalescing/particulate filter • Designed to process highly corrosive and difficult

samples including gas streams containing high levels of HCl, HF, NOX or SOX

• Yields sample dew points as low as -25ºC

800 242 3910 / www.ashtead-technology.com

ISO 9001 Certified

Did you know...Ashtead Technology stocks a full line of consumables?

For more information, please scan: