construction material finish - rotary connectors · 2 construction material finish shell alluminium...
TRANSCRIPT
2
CONSTRUCTION MATERIAL FINISH
Shell Alluminium Alloy Cadmium Olive Drab over Electroless Nickle Electroless NickleInsert Engineering Plastic NaturalO-ring Silicone Rubber NaturalContact Retainer Beryllium Copper NaturalContact Copper Alloy 1.27 µ Gold PlatedRetainer Alloy Steel PassivatedRivet Stainless Steel PassivatedGrounding Ring Beryllium Copper Natural
MECHANICAL
Endurance : 500 Cyclesfor MS 3475 : 250 Cycles
Size: 20 16 12Contact Retention Force (N) 88N 111N 133N
Vibration Random : Peak 41 G at 50 to 2000hz
Shock : 300g, 3ms
Connector EngagementForce (Torque) (MAX) : 0.9 to 4.95 Nm
Connector DisengagementForce (Torque) (min) : 0.112 to 0.78 Nm
CLIMATIC
Working Temperature: Class W : -55˚ to 175˚ CClasss L : -55˚ to 200˚ C
Resistance to Salt Spray:Class W : 500 hrs at 35˚ CClasss L : 48 hrs at 38˚ C
Shell Style
0 - Receptacle Square Flange1 - Receptacle Cable Mounting4 - Receptacle Jam Nut5- Plug RFI Shielded6 - Plug
Contact
P- Pin contact Crimp typeS- Socket contact Crimp typeA- Pin style less pin contactB- Socket style less socket contact
Rotary reserves the right to make any engineering refinement, alterations or improvements deemed necessary on its products. The dimensions appearing in this catalogue are thus subject to change without notice. When dimensions are critical, detailed drawings should be requested.
Orientation
Normal orientationno marking
W,X,Y,Z Alternative position Refer page - 5
Class
W- Cadmium Olive DrabL - Electroless Nickle
Shell Size
8, 10, 12, 14,16, 18, 20, 22, 24
Insert Arrangement
Ref P - 4
MS347 - X - X - XX - XX - X - X
ELECTRICAL
Voltate Rating AC Vrms
Service Rating At Sea Level At 70,000 Ft
I 1500V rms 375
II 2300V rms 500
Insulation Resistance : > 5000 MΩat 500vdc
Contact Size Current Rating (A)
20 7.5
16 13
8 23
Shell to Shell ConductivityWith RFI Spring fingure < 5 mΩWithout RFI Spring fingure < 200 mΩ
SPECIFICATIONS
CONFIGURATION
For other plating finish contact factory
3
JAM NUT RECEPTACLE
SHELL ØA B C L S F Q Thread SIZE MAX MAX MAX FLAT
8 12.03 17.95 2.87 30.85 24.20 13.34 1/2-20UNEF
10 15.01 17.95 2.87 30.85 27.40 16.51 5/8-24UNEF
12 19.07 17.95 2.87 30.85 32.15 20.55 3/4-20UNEF
14 22.25 17.95 2.87 30.85 35.35 23.8 7/8-20UNEF
16 25.42 17.95 2.87 30.85 38.50 26.95 1/20UNEF
18 28.60 17.95 2.87 30.85 41.65 30.12 1-1/16-18UNEF
20 31.77 19.60 3.76 32.40 46.60 33.3 1-3/16-18UNEF
22 34.95 19.60 3.76 32.40 49.60 36.47 1-5/16-18UNEF
24 38.12 19.60 3.76 32.40 52.75 39.65 1-7/16-18UNEF
PLUG
SHELL ØA L Q Thread SIZE MAX MAX
8 19.85 31.25 1/2-20UNEF
10 23.5 31.25 5/8-24UNEF
12 26.5 31.25 3/4-20UNEF
14 30.05 31.25 7/8-20UNEF
16 33.15 31.25 1-20UNEF
18 35.30 31.25 1-1/16-18UNEF
20 38.9 31.25 1-3/16-18UNEF
22 42.05 31.25 1-5/16-18UNEF
24 45.15 31.25 1-7/16-18UNEF
NARROW FLANGE RECEPTACLE
SHELL ØA B C E F ØT L Q Thread SIZE MAX MAX [TP] MAX MAX
8 12.03 11.70 1.95 15.09 21.03 3.05 36.5 1/2-20UNEF
10 15.01 11.70 1.95 18.26 24.23 3.05 36.5 5/8-24UNEF
12 19.07 11.70 1.95 20.62 26.59 3.05 36.5 3/4-20UNEF
14 22.25 11.70 1.95 23.01 28.98 3.05 36.5 7/8-20UNEF
16 25.42 11.70 1.95 24.61 31.34 3.05 36.5 1/20UNEF
18 28.60 11.70 1.95 26.97 33.73 3.05 36.5 1-1/16-18UNEF
20 31.77 14.35 2.75 29.36 36.91 3.05 36.5 1-3/16-18UNEF
22 34.95 14.35 2.75 31.75 40.08 3.05 36.5 1-5/16-18UNEF
24 38.12 15.25 2.75 34.92 43.26 3.73 38.1 1-7/16-18UNEF
CABLE CONNECTING RECEPTACLE
SHELL ØA B C P R L Q Thread SIZE MAX MAX MAX MAX MAX
8 12.03 11.70 1.57 21.05 24.35 30.86 1/2-20UNEF
10 15.01 11.70 1.57 24.25 27.50 30.86 5/8-24UNEF
12 19.07 11.70 1.57 26.60 29.90 30.86 3/4-20UNEF
14 22.25 11.70 1.57 30.00 32.25 30.86 7/8-20UNEF
16 25.42 11.70 1.57 31.35 34.65 30.86 1/20UNEF
18 28.60 11.70 1.57 33.75 37.00 30.86 1-1/16-18UNEF
20 31.77 14.90 2.39 36.90 40.20 32.40 1-3/16-18UNEF
22 34.95 14.90 2.39 40.10 43.30 32.40 1-5/16-18UNEF
24 38.12 15.75 2.39 43.25 46.50 32.40 1-7/16-18UNEF
CONTACT LAYOUT
VIEWED FROM THE FRONT FACE OF MALE INSULATOR
Note : * Insert arrangement available.4
ORIENTATION
VIEWED FROM THE FACE OF THE PIN INSERT
NOTE : 1) The position of the insert is rotated clock wise from the normal position (N) to the required angle “W” or “X” or “Y” or “Z”.
2) The different orientation is used when more than one connector with same contact layout is used. It avoids coupling of the connectors with its neighbour.
5
ANGLES IN DEGREES
W X Y Z
8
2 58 122 - - 3 60 210 - - 4 45 - - - 33 90 - - - 98 - - - -
10 6 90 - - -
7 - - - - 98 90 180 240 270
12
3 - - 180 - 8 90 112 203 292 10 60 115 270 295 14 - - - -
14
4 45 - - - 5 40 92 184 273 9 15 90 180 240 12 43 90 - - 15 17 110 155 234 18 15 90 180 270 19 30 165 315 - 22 45 - - -
16
8 54 152 180 331 14 25 78 180 240 23 158 270 - - 26 60 - 275 338 99 66 156 223 340
18
8 180 - - - 11 62 119 241 340 30 180 193 285 350 32 85 138 222 265 85 45 90 180 240
20
16 238 318 333 347 24 70 145 215 290 27 72 144 216 288 39 63 114 252 333 41 45 126 225 - 90 18 60 240 270
22
12 - - - - 19 15 90 225 308 21 16 135 175 349 32 72 145 215 228 34 62 142 218 298 41 39 135 264 - 55 30 142 226 314 95 26 180 266 -
24
19 30 165 315 - 27 45 110 140 225 31 90 225 255 - 61 90 180 270 324
LAYOUTSH
ELL
Accessories for Connector, Circular, Miniature, Bayonet Coupling, MIL-DTL-26482 Series II
6
80 - Cap for Plug81 - Cap for Receptacle
W - Cadmiun, Olive Drab FinishL - Electroless NckleA - Anodized Black
L - Chain or rope with length of 5.000+ .500/- .250 inchesin lieu of standard lengthfor standard length no markingC - With Chain
N - With chain & Ring (only for MS 3181)R - With Rope (Stainless Steel)
Shell size
MS31 X - X - X - X - X
Shell size
RE911 - FG - X
Ordering information for Flange Mounting gasket
PANEL CUTOUTS
WALL MOUNTING RECEPTACLE JAM NUT RECEPTACLE SHELL A B C E F SIZE
8 14.43 15.09 3.81 14.53 13.61
10 17.40 18.26 3.81 17.70 16.79
12 21.95 20.62 3.81 22.73 20.93
14 25.12 23.01 3.81 25.65 24.08
16 28.27 24.61 3.81 28.83 27.23
18 31.45 26.97 3.81 32.00 30.40
20 34.62 29.36 3.81 35.18 33.58
22 37.80 31.75 3.81 38.35 36.75
24 41.02 34.93 3.81 41.53 39.93
Shell F E A Size MAX DIA 8 20.62 15.08 12.90
10 23.82 18.26 16.07
12 26.18 20.65 19.25
14 28.57 23.01 22.42
16 31.96 24.61 25.60
18 33.32 27.00 28.77
20 36.52 29.36 31.95
22 39.70 31.75 35.13
24 42.87 34.92 38.30
7
Contacts Filler Plugs Insertion & Extraction Tool
Contacts Contact Part Number Specs Color Mil Spec Insert Color Extract size Type
20 Male M39029/4-110 MS 27488-2 Red M81969/14-02 Red White Female M39029/5-115
16 Male M39029/4-111 MS 27488-2 Blue M81969/14-03 Blue White Female M39029/5-116
12 Male M39029/4-113 MS 27488-2 Yellow M81969/14-04 Yellow White Female M39029/5-118
CONTACTS, FILLER PLUGS, INSERTION & EXTRACTION TOOL
MIL TYPES RE PART NO. DESCRIPTION
M85049/31S RE85049/31-XX-X Back Nut
M85049/52S RE85049/52S-XX-X Strain relief clamp straight
M85049/60-1 RE85049/60-1-XX-X Heat shrink boot adaptor
M85049/26-1 RE85049/26-1-XX-X RFI shielding, Crimp adaptor
M85049/26-2 RE85049/26-2-XX-X Crimping ring only
M85049/82 RE85049/82-XX-X Banding adaptor straight
M85049/83 RE85049/83-XX-X Banding adaptor 450 bend
M85049/84 RE85049/84-XX-X Banding adaptor 900 bend
W - Cadmium, Olive Drab FinishL - Electro less NickleA - Black Anodized
Shell sizeType
M85049 / XX - XX - Finish
Back Shells for Connectors Ordering Information