creating a simple motor. open office only
TRANSCRIPT
![Page 1: Creating a simple motor. open office only](https://reader030.vdocuments.net/reader030/viewer/2022032420/55a4482f1a28ab34748b4594/html5/thumbnails/1.jpg)
PrePared by: Melchor cariñob.S.i.T(icT)
iTfndS1 Thu 11:30 – 2:00
creaTing a SiMPle MoTorcreaTing a SiMPle MoTor
![Page 2: Creating a simple motor. open office only](https://reader030.vdocuments.net/reader030/viewer/2022032420/55a4482f1a28ab34748b4594/html5/thumbnails/2.jpg)
creaTing a SiMPle MoTor iS juST SiMPle.
brief deScriPTionbrief deScriPTion
![Page 3: Creating a simple motor. open office only](https://reader030.vdocuments.net/reader030/viewer/2022032420/55a4482f1a28ab34748b4594/html5/thumbnails/3.jpg)
MaTerialSMaTerialS
● Battery
● Thumb Tacks
● Insulated Copper
● Wood
● Two 3 and 1/2 inch nails
● Paper Clip
● Knife, Cutter, or Scissor
● Electrical Tape
● Long-Nose Plier
![Page 4: Creating a simple motor. open office only](https://reader030.vdocuments.net/reader030/viewer/2022032420/55a4482f1a28ab34748b4594/html5/thumbnails/4.jpg)
STeP 1STeP 1
Bend each clip using the long-nose Pliers
Get two of the clips
This is the Process
![Page 5: Creating a simple motor. open office only](https://reader030.vdocuments.net/reader030/viewer/2022032420/55a4482f1a28ab34748b4594/html5/thumbnails/5.jpg)
STeP2STeP2Place the first clipPlace 2 thumb tacksPlace the second clip with a distance of 1 inch
![Page 6: Creating a simple motor. open office only](https://reader030.vdocuments.net/reader030/viewer/2022032420/55a4482f1a28ab34748b4594/html5/thumbnails/6.jpg)
STeP 3STeP 3Get the third clipBend both ends Perpendicularly
Use the insulated copper to wind the clip tightly
20 turns
20 turns
Wrap the electrical tape on both ends as shown belowUse the knife or cutter to
remove the insulator Cut both ends of the copper
![Page 7: Creating a simple motor. open office only](https://reader030.vdocuments.net/reader030/viewer/2022032420/55a4482f1a28ab34748b4594/html5/thumbnails/7.jpg)
STeP 4STeP 4Get the two Nails
Wrap each nail with wire leaving about 9 inch of wire
Wrap each nail leaving 6 inch going up to the middle
Remove the Insulator using knife or cutter
![Page 8: Creating a simple motor. open office only](https://reader030.vdocuments.net/reader030/viewer/2022032420/55a4482f1a28ab34748b4594/html5/thumbnails/8.jpg)
STeP 5STeP 5Put the rotor clipGet the two electromagnet nails
and put it beside the arrow shown below
Hammer it down
![Page 9: Creating a simple motor. open office only](https://reader030.vdocuments.net/reader030/viewer/2022032420/55a4482f1a28ab34748b4594/html5/thumbnails/9.jpg)
STeP 6STeP 6Put the wire that will be
connected to the rotor clip Put thumb tacks on it Connect A and B
D
A
BC
-
+
Connect C and DThe 2 connections that are left will serve as + and – for the
battery
![Page 10: Creating a simple motor. open office only](https://reader030.vdocuments.net/reader030/viewer/2022032420/55a4482f1a28ab34748b4594/html5/thumbnails/10.jpg)
ouTcoMeouTcoMe