data sheet 2600t series pressure transmitters · 2018-05-10 · data sheet ss/s264_8 wide range of...

Data SheetSS/S264_8

■ Wide range of remote seal types- allow optimum design for each application

without compromise of performance

■ Large selection of options, materials and fillfluids- meet nearly all process requirements

■ All welded constructions- combine an economically feasible and technically

sound solution ensuring total reliability at linepressure down to full vacuum

■ Special designed remote seals for individualprocess solutions- add flexibility for most demanding services

2600T Series Pressure Transmitters

Models S264 Remote Seals

ABB 2600T SeriesEngineered solutions

for all applications

2600T Pressure TransmittersModels S264 SS/S264_8

2

Remote Seals OverviewThe S264x seals are used in combination with 2600T transmitters,allowing differential, gauge or absolute pressure measurements.Connection of the seal(s) to the relevant transmitter can beachieved as follows :- directly mounted with a short capillary connecting the "integral"

seal to the transmitter sensor;- through a capillary system which link the transmitter sensor to

a "remote" seal of any version.Using remote seal the transmitter can be selected with- two seals using same fill fluid, capillary and diaphragm size- one seal having the other side configured with a process flange

for wet/dry leg connection or a blind flange providing vacuum oratmospheric reference.

Model 264HR/NR transmitters have always one remote seal only,with a selectable reference to atmosphere or vacuum respectivelyfor gauge or absolute pressure measurements.The S264x Series Seal System is a protective device used toisolate 2600T series transmitters from the process fluid.The seal system provides a flexible diaphragm seal between theprocess fluid and a liquid filled capillary tube connected to thebody of the transmitter. The diaphragm isolates the process fluidwhile the filled capillary tube hydraulically transmits the processpressure to the transmitter sensor. The capillary of remote seal iscorrosion-resistant with robust costruction in stainless steel withspiral armour protection, also PVC jacket; PVC protection isalways recommended except for high temperature application,where stainless steel armour is suggested.The all welded construction assures reliable operation over thewidest range of operating temperature and under vacuumconditions.For certain applications, use of seal is necessary to prevent theprocess fluid from leaving its enclosure, due to reasons such as :• the process fluid has solids in suspension or is highly viscous

and can foul impulse lines.• the process fluid can solidify in impulse lines or the

transmitter.• the process fluid is too hazardous to enter the control area

where the transmitter is located.• the process temperature exceeds the recommended limits

for the transmitter.• the application is interface level or density measurement.

Remote seals offer the required constant and equal specificgravity of the pressure transfer fluid on the high and low sidesof the transmitter.

• the transmitter must be located away from the process foreasier maintenance.

The S264x series is available with process connections for ASMEor EN pipe flanges, wedge flow elements, chemical tees, andthreaded pipe fittings. Extended diaphragm remote seals,suitable for connection to 2in - 3in or 4in flanged tank nozzles orflanged tees, permit the seal diaphragm to be located flush withthe inside of a tank or pipe. Sanitary type seals meet the stringentrequirements of sanitary food, dairy, pharmaceutical and BioTech applications, offering FDA approved fillings and compliancewith 3-A Sanitary Standards.Fill fluids with FDA are defined as food fills and are GenerallyRecognized As Safe (GRAS) by the US Food and DrugAdministration (FDA).

Seal system selection criteriaApplication of an S264x system in direct mount or remote sealconfiguration to 2600T transmitters affects performances oforiginal devices. Effects are evident in:- Accuracy- Temperature effects- Dynamic response

• AccuracyAccuracy is only marginally affected when seal diaphragmstiffness is relevant compared with sensor stiffness. This is theonly characteristic of the S264x system which has role onaccuracy performance. High stiffness of diaphragm associatedwith low URL might produce increased errors of linearity,hysteresis, and long term stability; when diaphragm stiffness isaccuracy related also temperature effects are significantlyaffected. Some basic considerations on diaphragm stiffness helpunderstanding effects introduced by S264x system associatedwith transmitters. This is physically defined by the ratio betweenthe pressure variation applied to the diaphragm and thecorresponding volume variation. The stiffness is not linear alongthe whole diaphragm volumetric displacement, but the S264xdesign is such to maintain the system linear within the serviceconditions of the transmitter such as:- Operating pressure range- Operating static pressure (for differential transmitters)- Ambient & process temperature limitsDiaphragm stiffness is a function of material & thickness (elasticcoefficient), diameter (type), convolution shape and geometry(design defined)

• Temperature effectsS26 system has effect on temperature performance of the com-plete transmitter. This effect is mostly on zero of the instrumentand is produced by the expansion of the fill fluid into the closedvolume formed by the transmitter flange cavity the capillaryvolume and the remote seal volume. This volume filled with a fluidwith specific expansion coefficient; change in temperature of themeasuring device produce a volume variation which is absorbedby the remote diaphragm, whose stiffness produces a change inthe fluid pressure: this is the zero error. In real application thetransmitter/seal system is not the same and stable temperature.Therefore the errors referred in this document for each type ofdiaphragm and different fluids should be taken as a reference forqualitatively evaluation and not a true behaviour in normalapplication conditions. Should again be recognized that thestiffness of diaphragm and in this case, the thermal coefficient offluid are the parameter to take into account.

• Time responseApplication of S264x seal to transmitters increases the originaltime response. The amount of the increase depends from thenumber of elements and condition of the instrument as follows :- transmitter sensor range- physical configuration (i.e. a remote seal on other side)- type of measure/number of seal (one or two)- fill fluid viscosity of the S264x system applied- ambient temperature (affects the transmitter and the capillary)

and process temperature on the seal diaphragm- capillary length


3

The delay introduced by the seal may be considered as an addedconstant time to the one of the associated transmitterFor obtaining the best application solution :• choose sensor code with URL closest to application SPAN• select largest diameter diaphragm seal related to URL.• keep the capillary length as short as possible• select the fill fluid that suits the most extreme process

conditions expected (highest temperature and lowestpressure) and it is compatible with the process fluid.

• In vacuum application, choose always the all welded versionand mount the transmitter primary 30 cm/12 inches or morebelow the bottom seal connection.

• In a two-seal system use the same diaphragm size, capillarylength and fill fluid on each side of the transmitter.

Ordering InformationThe transmitter and each seal system are each identified by aproduct code number. These code numbers are stamped on thetransmitter nameplate and each character identifies specificproduct features. Refer to ordering information for a detailedexplanation of the product code numbers.A typical example of the product code stamping is as follows :

Transmitter Product Code 264DRFSSA1AH–V1E1D3Seal System Product Code S264WHBCDFSBES1NNN

Industrial application in chemical, sanitary, food and any otherprocess industries may require seal configurations and/orprocess connection different from those reported in thisdocument. Each “special” should be evaluated by ABB to checkthe correctness and its level of functionality. Ask for the “S264xseries seal form” to define precisely the measuring problem andapplication requirements.

The following table shows the types of standard seals consideredin this leaflet. The mnemonics will be used as shortest crossreferences with the transmitter data sheet which should be read inconjunction with this data sheet.

ABB can also cooperate with you by developing a special remote seal for problems requiring individual solutions.

PLEASE CONTACT YOUR LOCAL ABB OFFICE OR REPRESENTATIVE FOR ADDITIONAL INFORMATION, SPECIFIC SEAL DATAAND APPLICABILITY.

Absolute viscosity (cP) = Kinematic Viscosity (cSt) x Specific gravity at specified temperature.The absolute viscosity value is used for response time calculation.

SEALS DIMENSIONS ON FOLLOWING PAGES ARE IN mm (in)

FILL FLUID CHARACTERISTICS (Table A)

ledoM epytlaeS eziS cinomenM

W462SrefaW

)doof(refaW

1 1/2 04ND/ni05ND/ni208ND/ni3

5.1P2P3P

C462SeetlacimehC

degnalfni3 3P

A462SE462SG462SR462S

degnalFmgarhpaidhsulftnioJgniRosla(

)dradnatsSIJdna

-1 1/2 )ylnoJREMSA(ni05A/05ND/ni2

/001-08ND/ni4-3001-08A

5.1P2P3P

degnalFdednetxemgarhpaid

05ND/ni208ND/ni3001ND/ni4

2E3E3P

U462S noinU 1 1/2 ni 5.1Z

T462S enil-ffodedaerhT 2 1/2 ni 5.2T

M462S enil-ffodegnalF 2 1/2 ni 5.2T

S462S

tunnoinUpmalcirT

lerruByrrehCcitpesA,yratinaS

05F/ni208F/ni3

ni4

2S3S3S

B462S nottuB ni1 1B

P462SecivresaerU

degnalf1 1/2 ni2 1/2 ni

5.1U5.2U

SDIULFLLIF)NOITACILPPA(

SNOITIDNOCGNITAREPO )F°77(C°52TANOITACIFICEPS

xamTfo>sbaP@

nimPsbarabm

)aisp(

xamTnimP@

nimT cificepSytivarg

citameniKytisocsiv

)tSc(

lamrehTnoisnapxe

01x( 3- )C°/™002CD-lioenociliS

)esopruplareneG()093(002rabm53@

7.0)10.0(

061)023(

04–)04–(

439.0 01 80.1

™041NA-lioenociliS)erutarepmethgiH(

)617(083rab1@

7.0)10.0(

003)275(

5–)32+(

70.1 04 46.0

™TLXmrehtlyS–remyloPenociliS)erutarepmetwoL(

)212(001rabm011@

2)30.0(

02)86(

001–)841–(

258.0 4.1 1

™02-MeeboeN-lioelbategeVADF)yratinaS-dooF(

)093(002rab1@

031)9.1(

051)003(

81–)0(

29.0 8.9 2.1

)%07(retaWnirecylGADF)yratinaS-dooF(

)002(39rab1@

0001)5.41(

39)002(

7–)02+(

80.1 2.2 63.0

™28LOCRAM-liolareniMADF)yratinaS-dooF(

)093(002rabm002@

33)5.0(

04)401(

04–)04–(

48.0 62 40.1

™nedlaG–trenI)ecivreSnegyxO(

)023(061rab1@

2)30.0(

07)851(

02–)4–(

28.1 4.4 1.1

2.4™nobracolaH–trenI)ecivreSnegyxO(

)653(081rabm004@

4)60.0(

07)851(

02–)4–(

78.1 3.6 468.0


4

S264W Model Wafer Remote SealThe wafer remote seal is designed to be clamped between two ASME or EN raised face flanges. The diaphragm side of the seal facesthe process flange and a blind back-up flange is used on the other side of the seal.The wafer variant is also available as food design for 11/2in and 3in sizes.

134

(5.3

)

B

A /

A1

C

D

Flushing ring(OPTION)

25 (0.98) for 1/4 NPT

33 (1.30) for 1/2 NPTflushing thread(s)

Capillary toinstrument


Gasket seat finish

23 (0.9);25 (0.98)

for 1-1/2in food

eziS

)ni(mmSNOISNEMID

)aid(A.hpaid

1AgnihsulF

.aid.tnignir

)aid(B C D

1 1/2 ni )79.1(05 )50.2(25 )78.2(37 )20.3(8.67

6.1)60.0(

ni2 )63.2(06 )44.2(26 )26.3(29 )77.3(8.59

ni3 )5.3(98 )26.3(29 )5(7218.031)51.5(

04ND )79.1(05 )50.2(25 )64.3(88 )26.3(29

3)21.0(

05ND )63.2(06 )44.2(26201

)20.4()71.4(601

08ND )5.3(98 )26.3(29831

)34.5()95.5(241

1 1/2 ni)doof(

)79.1(05 )50.2(25 )78.2(37 )20.3(8.67 .A.N

ni3)doof(

)5.3(98 )26.3(29 )5(7218.031)51.5(

7.3)51.0(


5

Maximum Working Pressure

WAFER SEAL ELEMENT : 16 MPa, 160 bar, 2320 psi but notgreater than the backup flange rating (not supplied).

Vacuum Service

Full vacuum subject to fill fluid limits. Refer to table A.

Minimum pressure with tantalum diaphragm is 1kPa abs, 10mbar abs,0.15psia.

Process Temperature Limits

Same as fill fluid limits. Refer to table A.

260°C (500°F) for Tantalum diaphragm.

204°C (400°F) for use with Teflon anti-stick coating.

320°C (608°F) for AISI gold plated diaphragm.

Limits for gaskets of flushing rings

Gasket seat finish

Smooth (ASME or EN): 0.8µm (Ra)

Serrated (ASME): 3.2 to 6.3µm (Ra)

Serrated (EN 1092-1 Type B1; up to PN40): 3.2 to 12.5 µm (Ra)

Serrated (EN 1092-1 Type B2; PN63 - 100): 0.8 to 3.2 µm (Ra)

Temperature effect

The following table shows the temperature effect for 20K (36°F)change, detailed separately for

a) the seal (one element)

b) the capillary per meter

c) the system (transmitter sensor when combined with a seal ofspecific size/type)

referred to silicone oil (DC 200) filling and AISI 316 L ss diaphragmmaterials.

For filling different from silicone oil (DC200) the errors can be multipliedby ratio between the thermal expansion coefficients of the selectedfilling divided by the one of DC200, listed in the fill fluid characteristicstable.

THE ERRORS IN TABLE CAN BE CONSIDERED DIVIDED BY 4 FORTRANSMITTERS USING SAME REMOTE SEAL ON THE TWO SIDES

eziSlaeSrefaW rorrelaeS rorrEyrallipaCm1 rorrE)rosneS(metsyS

1 1/2 04ND/ni Hni5.3,rabm7.8,aPk78.0 2O Hni2.1,rabm3,aPk3.0 2O Hni6.3,rabm9,aPk9.0 2O

05ND/ni2 Hni61.1,rabm9.2,aPk92.0 2O Hni82.0,rabm7.0,aPk70.0 2O Hni8.0,rabm2,aPk2.0 2O

08ND/ni3 Hni63.0,rabm9.0,aPk90.0 2O Hni21.0,rabm3.0,aPk30.0 2O Hni21.0,rabm3.0,aPk30.0 2O

lairetaM erusserP).xam(

erutarepmeT).nim().xam(

timilTxP

kcolraG,rab96,aPM9.6

isp0001C°402

)F°004(C°37–

)F°001–(000052

)ispxF°(

etihparG,rab52,aPM5.2

isp263C°083

)F°617(C°001–

)F°841–(

EFTP,rab06,aPM6

isp078C°052

)F°284(C°001–

)F°841–(


6

BASIC ORDERING INFORMATION model S264W Wafer Remote SealSelect one character or set of characters from each category and specify complete catalog number.

LEDOMESAB 1– ts 5ot ht sretcarahc S 2 6 4 W X X X X F X X X X X d'tnoC

laeSetomeRrefaW

–noitcennocfoedisrettimsnarT 6 ht retcarahcedishgiHediswoL

HL

metsysgniretneC 7– ht retcarahc)egnalfpukcabEMSArofelbatius(retemaidkcabnotaeS B

eziS – 8 ht retcarahc

1 1/2 EMSAniEMSAni2EMSAni3

1 1/2 ngiseddoofEMSAningiseddoofEMSAni3

04NDNE05NDNE08NDNE

ABC12DEF

hsiniftaeS 9– ht retcarahc

)EMSArofelbatius(hsinifdetarreS)EMSArofelbatius(hsinifhtoomS

04NPotpu;1BepyT1-2901NEothsinifdetarreS001NPot36NP;2BepyT1-2901NEothsinifdetarreS

)NErofelbatius(hsinifhtoomS

)2,1setoN()1etoN(

)3,2setoN()3,2setoN()3,2setoN(

DERST

edocesU 01– ht retcarahc F

lairetammgarhpaiD 11– ht retcarahc

ssL613ISIA™672CyolletsaH

™0002CyolletsaH526lenocnI

mulatnaTdetalpdlogssL613ISIA

gnitaockcits–itnahtiwssL613ISIAgnitaockcits–itnahtiw™672CyolletsaH

gnitaockcits-itnadnanoisorroc-itnahtiwssL613ISIA)tnemtaertnoisarbAitnAhtiwISIA(xelfaiD

)974ASMTSAot05723SSNU(ssxelpudrepuS

)4,2setoN()4,2setoN()4,2setoN()4,2setoN()4,2setoN()4,2setoN()4,2setoN()4,2setoN(

)2etoN()2etoN(

ECANECANECANECAN

ECANECANECANECANECANECAN

SHMLTNKYWFE

noitcetorpyrallipaC 21– ht retcarahc

ruomrassL613ISIArevocevitcetorpCVPhtiwruomrassL613ISIA

)ERUTAREPMETHGIHROFDEDNEMMOCER( AB

)teef(mhtgnelyrallipaC 31– ht retcarahc

)3(1)5(5.1

)7(2)8(5.2)01(3

)21(5.3)31(4

)51(5.4)71(5

)81(5.5)02(6

)22(5.6)32(7

)52(5.7)72(8)03(9

)33(01)04(21)74(41)35(61

ABCDEFGHJKLMNPQRSTUV

diulflliF 41– ht retcarahc

lioenociliSnedlaG-diulftrenI

nobracolaH-diulftrenIerutarepmethgihroflioenocilIS

erutarepmetwolrofremylopenociliS)devorppaADF(liolareniM

)devorppaADF(lioelbategeV)devorppaADF(retaw-nirecylG

)5,2setoN()5,2setoN(

)2etoN()2etoN()6etoN()6etoN()6etoN(

SNDHCWAB

noitacifitreC 51– ht retcarahc

enoN 1


7

Note 1: Not available with EN size code D, E, F

Note 2: Not available with food design size code 1, 2

Note 3: Not available with ASME size code A, B, C

Note 4: Not available with serrated seat finish code D, R, S

Note 5: Suitable for oxygen service

Note 6: Suitable for food application

Note 7: Not available with flushing ring - hole and thread code 2, 3, 4, 5

Note 8: Not available with flushing ring - hole and thread code N

Note 9: Not available with flushing ring material code H

Note 10: Not available with AISI 316L flushing ring material code A

W462SNOITAMROFNIGNIREDROCISAB X X X

daerhtdnaeloh:gnirgnihsulF 61– ht retcarahc

enoNTPNni2/1-eloh1TPNni2/1-seloh2

TPNni4/1-eloh1TPNni4/1-seloh2

N2345

lairetamgnirgnihsulF 71– ht retcarahc

enoNssL613ISIA

672CyolletsaH

)7etoN()8etoN(

)8,4setoN(ECANECAN

NAH

teksagdnagulp:gnirgnihsulF 81– ht retcarahc

teksagon-gulpoNkcolrag-gulpoN

EFTP-gulpoNetihparg-gulpoN

teksagon-ssL613ISIAkcolrag-ssL613ISIA

EFTP-ssL613ISIAetihparg-ssL613ISIA

teksagon-672CyolletsaHkcolrag-672CyolletsaH

EFTP-672CyolletsaHetihparg-672CyolletsaH

)8etoN()8etoN()8etoN(

)9,8setoN()9,8setoN()9,8setoN()9,8setoN(

)01,8setoN()01,8setoN()01,8setoN()01,8setoN(

NABCDEFGHLMP


8

S264C Model Chemical Tee Remote SealThe chemical tee remote seal is designed to connect to a Wedge Flow Element or to any process fitting with appropriate matingcondition.Chemical tee elements cannot be connected to a standard ASME or DIN pipe flange.


2 MPa, 20 bar, 300 psi

Vacuum Service

Full vacuum subject to fill fluid limits.

Refer to table A.




–100°C (–148°F) to 260°C (500°F) with PTFE gasket

–100°C (–148°F) to 340°C (645°F) with graphite gasket

Temperature effect







THE ERRORS IN TABLE CAN BE CONSIDERED DIVIDED BY 4FOR TRANSMITTERS USING SAME REMOTE SEAL ON THE TWOSIDES

Capillary to instrument

DiaphragmSurface

eeTlacimehCeziSlaeS

rorrelaeS rorrEyrallipaCm1 rorrE)rosneS(metsyS

ni3 Hni63.0,rabm9.0,aPk90.0 2O Hni21.0,rabm3.0,aPk30.0 2O Hni21.0,rabm3.0,aPk30.0 2O

dia 127 (5)

dia

89 (3

.5)

8 Mounting Holesdia 8.73 (0.34)Equally Spaced

134 (5.3)

25 (1)12 (0.47)

dia 111 (4.38)


9

BASIC ORDERING INFORMATION model S264C Chemical Tee Remote SealSelect one character or set of characters from each category and specify complete catalog number.



LEDOMESAB 1– ts 5ot ht sretcarahc S 2 6 4 C X X X P X X X X X

laeSetomeReeTlacimehC


HL

egnalfgnitnuoM 7– ht retcarahclaeshtiwlargetnI P

eziS 8– ht retcarahc)gnitarrab02;dradnatsyrateirporp(ni3 G

edocesU 9– ht retcarahc




gnitaockcits-itnadnanoisorroc-itnahtiwssL613ISIA

ECANECANECANECANECAN

SHKYW





)3(1)5(5.1

)7(2)8(5.2)01(3

)21(5.3)31(4

)51(5.4)71(5

)81(5.5)02(6

)22(5.6)32(7

)52(5.7)72(8)03(9

)33(01

ABCDEFGHJKLMNPQRS






)1etoN()1etoN(


SNDHCWAB

teksaG 41– ht retcarahc

enoNrellifaciliShtiwEFTP

etihparG

167


10

S264F Model Flanged Extended and Flush Diaphragm Remote SealThe extended and flush diaphragm remote seal is designed to connect to ASME or EN flanged pipe fitting. For liquid levelmeasurement installations the seal connects to an ASME or EN flanged tank nozzle (Schedule 40).The sealing is provided by a selectable smooth or serrated gasket seat surface finish.

Flanged Extended Diaphragm Seal Flanged Flush Diaphragm Seal

Capillary toInstrument


158 (6.22)

E

C A B

F G

D

158 (6.22)

B

F G

C

E

A D

50, 100 or 150mm(1.97, 3.94 or 5.91)

insertion length is available

gnitaR/eziS gnitaR/eziS gnitaR/eziS gnitaR/eziS gnitaR/eziS

)ni(mmsnoisnemiD )ni(mmsnoisnemiD )ni(mmsnoisnemiD )ni(mmsnoisnemiD )ni(mmsnoisnemiDfo°N fo°N fo°N fo°N fo°Nseloh seloh seloh seloh seloh)aid(A )aid(A )aid(A )aid(A )aid(A

)aid(B )aid(B )aid(B )aid(B )aid(B )aid(C )aid(C )aid(C )aid(C )aid(C )aid(D )aid(D )aid(D )aid(D )aid(D )aid(E )aid(E )aid(E )aid(E )aid(E FFFFF GGGGGhsulf hsulf hsulf hsulf hsulf dednetxe dednetxe dednetxe dednetxe dednetxe

61NPNE05ND04NPNE05ND36NPNE05ND001NPNE05ND

61NPNE08ND04NPNE08ND36NPNE08ND001NPNE08ND61NPNE001ND04NPNE001ND

)63.2(06)63.2(06)63.2(06)63.2(06

)5.3(98)5.3(98)5.3(98)5.3(98)5.3(98)5.3(98

)9.1(84)9.1(84

ANAN

)38.2(27)38.2(27

ANAN

)7.3(49)7.3(49

)20.4(201)20.4(201)20.4(201)20.4(201)34.5(831)34.5(831)34.5(831)34.5(831)22.6(851)83.6(261

)29.4(521)29.4(521)13.5(531)17.5(541

)3.6(061)3.6(061)7.6(071)80.7(081)80.7(081)84.7(091

)5.6(561)5.6(561)80.7(081)76.7(591)78.7(002)78.7(002)64.8(512)50.9(032)66.8(022)52.9(532

)17.0(81)17.0(81)68.0(22)20.1(62)17.0(81)17.0(81)68.0(22)20.1(62)17.0(81)68.0(22

)97.0(02)97.0(02)20.1(62

)1.1(82)97.0(02)49.0(42

)1.1(82)62.1(23)97.0(02)49.0(42

)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9

4444888888



)aid(B )aid(B )aid(B )aid(B )aid(B )aid(C )aid(C )aid(C )aid(C )aid(C )aid(D )aid(D )aid(D )aid(D )aid(D )aid(E )aid(E )aid(E )aid(E )aid(E FFFFF GGGGGhsulf hsulf hsulf hsulf hsulf dednetxe dednetxe dednetxe dednetxe dednetxe

051LCEMSAni2003LCEMSAni2006LCEMSAni2009LCEMSAni2051LCEMSAni3003LCEMSAni3006LCEMSAni3009LCEMSAni3051LCEMSAni4003LCEMSAni4

)63.2(06)63.2(06)63.2(06)63.2(06

)5.3(98)5.3(98)5.3(98)5.3(98)5.3(98)5.3(98

)9.1(84)9.1(84

ANAN

)38.2(27)38.2(27

ANAN

)7.3(49)7.3(49

)26.3(29)26.3(29)26.3(29)26.3(29

)5(721)5(721)5(721)5(721

)2.6(2.751)2.6(2.751

)57.4(56.021)5(721)5(721

)5.6(561)6(4.251

)26.6(51.861)26.6(51.861

)5.7(5.091)5.7(5.091

)88.7(2.002

)6(4.251)5.6(1.561)5.6(1.561)5.8(9.512)5.7(5.091

)52.8(55.902)52.8(55.902

)84.9(142)9(6.822)01(452

)97.0(02)97.0(02)97.0(02)20.1(62)97.0(02)68.0(22)68.0(22)20.1(62)97.0(02)68.0(22

)57.0(50.91)88.0(53.22

)1(4.52)5.1(1.83

)49.0(78.32)21.1(44.82)52.1(57.13

)05.1(1.83)49.0(42)62.1(23

)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9

4888488888


11


The pressure limit decreases with increasing temperature above120°C for carbon steel or 20°C for AISI 316 stainless steel,according to DIN 2401 standards.

The pressure limit decreases with increasing temperature above100°F (38°C), according to ASME B16.5 standards.

Vacuum Service



dednetxEdegnalFmgarhpaiDeziSlaeS


05ND/ni2 Hni2.1,rabm3,aPk3.0 2O Hni4.0,rabm1,aPk1.0 2O Hn2.1,rabm3,aPk3.0 2O



hsulFdegnalFmgarhpaiDeziSlaeS





Flanged Extended Diaphragm Remote Seal

Flanged Flush Diaphragm Remote Seal





Gasket seat finish





Temperature effect




c) the system (transmitter sensor when combined with a sealof specific size/type)




ssalC/gnitaR1-2901NEot

leetSnobraCC°021@

leetSsselniatS613ISIAC°02@

61NP rab61 rab61

04NP rab04 rab04

36NP rab36 rab36

001NP rab001 rab001

ssalC/gnitaR5.61BEMSAot

leetSnobraC)C°83(F°001@

leetSsselniatS613ISIA)C°83(F°001@

051ssalC isp582 isp572





12

BASIC ORDERING INFORMATION model S264F Flanged Remote Seal (flush and extended)Select one character or set of characters from each category and specify complete catalog number.

LEDOMESAB 1– ts 5ot ht sretcarahc S 2 6 4 F X X X X X X X d'tnoC

)dednetxednahsulf(laesetomeRdegnalF


HL

egnalfgnitnuoM 7– ht retcarahcgnitatoR R


ni2ni2ni2ni2ni3

ngiseddoofni3ni3ni3ni3ni4ni4

05ND05ND05ND08ND08ND08ND08ND001ND001ND

051LCEMSA003LCEMSA006LCEMSA009LCEMSA051LCEMSA051LCEMSA003LCEMSA006LCEMSA009LCEMSA051LCEMSA003LCEMSA

04/61NPNE36NPNE

001NPNE61NPNE04NPNE36NPNE

001NPNE61NPNE04NPNE

ADGJB1EHKCFMPRNLQSTU

)laes(mroftaeS/egnalfgnitnuoM 9– ht retcarahc

leetsnobraCleetsnobraCleetsnobraCleetsnobraC

ss613ISIAss613ISIAss613ISIAss613ISIA

hsinifdetarres–)ecafdesiar(FRmroFhsinifhtooms–)ecafdesiar(FRmroF

hsinifdetarres–2B/1BepyT1-2901NEhsinifhtooms–2B/1BepyT1-2901NE

hsinifdetarres–)ecafdesiar(FRmroFhsinifhtooms–)ecafdesiar(FRmroF

hsinifdetarres–2B/1BepyT1-2901NEhsinifhtooms–2B/1BepyT1-2901NE

)3,1setoN()3,1setoN()3,2setoN()3,2setoN()3,1setoN(

)1etoN()3,2setoN()3,2setoN(

ABGPDELQ

lairetamdnahtgnelsnoisnetxE 01– ht retcarahc

)lairetammgarhpaidroftxenees(hsulF)ni2(mm05)ni2(mm05)ni4(mm001)ni4(mm001)ni6(mm051)ni6(mm051

ssL613ISIA™672yolletsaH



)4,3setoN()6,4,3setoN(



F123456

)laes(lairetammgarhpaiD 11– ht retcarahc


mulatnaTgnitaockcits–itnahtiwssL613ISIA

gnitaockcits–itnahtiw™672CyolletsaHgnitaockcits-itnadnanoisorroc-itnahtiwssL613ISIA

)5etoN()6etoN(



ECANECAN

ECANECANECAN

SHTKYW





13

Note 1: Not available with EN mounting flange code M, P, R, N, L, Q, S, T, U

Note 2: Not available with ASME mounting flange code A, D, G, J, B, E, H, K, C, F

Note 3: Not available with 3in ASME CL150 food design size code 1

Note 4: Not available with ASME CL 600 and CL 900 mounting flange rating code G, J, H, K and with EN PN63, PN100

mounting flange code P, R, Q, S

Note 5: Not available with Hastelloy C276 extension code 2, 4, 6

Note 6: Not available with serrated seat finish code A, G, D, L

Note 7: Not available with extension code 1, 2, 3, 4, 5, 6

Note 8: Not available with 2in, DN50, DN80, DN100 mounting flange code A, D, G, J, M, P, R, N, L, Q, S, T, U



F462SNOITAMROFNIGNIREDROCISAB X X X


)3(1)5(5.1

)7(2)8(5.2)01(3

)21(5.3)31(4

)51(5.4)71(5

)81(5.5)02(6

)22(5.6)32(7

)52(5.7)72(8)03(9

)33(01)04(21)74(41)35(61








)3etoN()3etoN(


SNDHCWAB


enoN 1


14

S264A - S264E Models Flanged Extended and Flush Diaphragm Remote SealThe extended and flush diaphragm remote seal is designed to connect to flanged pipe fitting, according to ASME (mod. S264A) orEN (mod. S264E) standards. For liquid level measurement installations the seal connects to an ASME or EN flanged tank nozzle(Schedule 40). The sealing is provided by a selectable smooth or serrated gasket seat surface finish.

Flanged Extended Diaphragm Seal Flanged Flush Diaphragm Seal



158 (6.22)

E

C A B

F G

D50, 100 or 150mm(1.97, 3.94 or 5.91)

insertion length is available



)aid(B )aid(B )aid(B )aid(B )aid(B )aid(C )aid(C )aid(C )aid(C )aid(C )aid(D )aid(D )aid(D )aid(D )aid(D )aid(E )aid(E )aid(E )aid(E )aid(E FFFFF GGGGGdednetxe dednetxe dednetxe dednetxe dednetxemgarhpaid mgarhpaid mgarhpaid mgarhpaid mgarhpaid

hsulf hsulf hsulf hsulf hsulfmgarhpaid mgarhpaid mgarhpaid mgarhpaid mgarhpaid

gnirgnihsulf gnirgnihsulf gnirgnihsulf gnirgnihsulf gnirgnihsulfaidlanretni aidlanretni aidlanretni aidlanretni aidlanretni

051LCEMSAni2003LCEMSAni2006LCEMSAni2009LCEMSAni20051LCEMSAni2

051LCEMSAni3003LCEMSAni3006LCEMSAni3009LCEMSAni30051LCEMSAni3051LCEMSAni4003LCEMSAni4

)9.1(84)9.1(84

ANANAN

)38.2(27)38.2(27

ANANAN

)7.3(49)7.3(49

)63.2(06)63.2(06)63.2(06)63.2(06)63.2(06

)5.3(98)5.3(98)5.3(98)5.3(98)5.3(98)5.3(98)5.3(98

)44.2(26)44.2(26)44.2(26)44.2(26)44.2(26)26.3(29)26.3(29)26.3(29)26.3(29)26.3(29)26.3(29)26.3(29

)26.3(29)26.3(29)26.3(29)26.3(29)26.3(29

)5(721)5(721)5(721)5(721)5(721

)2.6(2.751)2.6(2.751

)57.4(56.021)5(721)5(721)5.6(561)5.6(561)6(4.251

)26.6(51.861)26.6(51.861

)5.7(5.091)8(2.302)5.7(5.091)88.7(2.002

)6(4.251)5.6(1.561)5.6(1.561)5.8(9.512)5.8(9.512)5.7(5.091)52.8(55.902)52.8(55.902

)84.9(142)5.01(7.662

)9(6.822)01(452

)97.0(02)97.0(02)97.0(02)20.1(62)20.1(62)97.0(02)68.0(22)68.0(22)20.1(62

)52.1(57.13)97.0(02)68.0(22

)57.0(50.91)88.0(53.22

)1(4.52)5.1(1.83)5.1(1.83)49.0(78.32)21.1(44.82)52.1(57.13

)05.1(1.83)88.1(8.74

)49.0(42)62.1(23

)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9

488884888888



)aid(B )aid(B )aid(B )aid(B )aid(B )aid(C )aid(C )aid(C )aid(C )aid(C )aid(D )aid(D )aid(D )aid(D )aid(D )aid(E )aid(E )aid(E )aid(E )aid(E FFFFF GGGGGdednetxe dednetxe dednetxe dednetxe dednetxemgarhpaid mgarhpaid mgarhpaid mgarhpaid mgarhpaid


gnirgnihsulf gnirgnihsulf gnirgnihsulf gnirgnihsulf gnirgnihsulfaidlanretni aidlanretni aidlanretni aidlanretni aidlanretni

61NPNE05ND04NPNE05ND36NPNE05ND001NPNE05ND

61NPNE08ND04NPNE08ND36NPNE08ND001NPNE08ND61NPNE001ND04NPNE001ND

)9.1(84)9.1(84

ANAN

)38.2(27)38.2(27

ANAN

)7.3(49)7.3(49

)63.2(06)63.2(06)63.2(06)63.2(06

)5.3(98)5.3(98)5.3(98)5.3(98)5.3(98)5.3(98

)44.2(26)44.2(26)44.2(26)44.2(26)26.3(29)26.3(29)26.3(29)26.3(29)26.3(29)26.3(29

)20.4(201)20.4(201)20.4(201)20.4(201)34.5(831)34.5(831)34.5(831)34.5(831)22.6(851)83.6(261

)29.4(521)29.4(521)13.5(531)17.5(541)3.6(061)3.6(061)7.6(071)80.7(081)80.7(081)84.7(091

)5.6(561)5.6(561)80.7(081)76.7(591)78.7(002)78.7(002)64.8(512)50.9(032)66.8(022)52.9(532

)17.0(81)17.0(81)68.0(22)20.1(62)17.0(81)17.0(81)68.0(22)20.1(62)17.0(81)68.0(22

)97.0(02)97.0(02)20.1(62)1.1(82)97.0(02)49.0(42)1.1(82)62.1(23)97.0(02)49.0(42

)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9

4444888888

25 (0.98) for 1/4 NPT

33 (1.30) for 1/2 NPTflushing thread(s)

Flushing ring(OPTION)

158 (6.22)

B

F G

C

E

A D


15


The pressure limit decreases with increasing temperature above120°C for carbon steel or 20°C for AISI 316 stainless steel,according to DIN 2401 standards.


Vacuum Service


Minimum pressure with tantalum diaphragm is 1kPa abs,10mbar abs, 0.15psia.






dednetxEdegnalFmgarhpaiDeziSlaeS


05ND/ni2 Hni2.1,rabm3,aPk3.0 2O Hni4.0,rabm1,aPk1.0 2O Hn2.1,rabm3,aPk3.0 2O








Flanged Extended Diaphragm Remote Seal


Gasket seat finish





Temperature effect








ssalC/gnitaR1-2901NEot

leetSnobraCC°021@


61NP rab61 rab61

04NP rab04 rab04

36NP rab36 rab36

001NP rab001 rab001









Limits for gaskets of flushing rings

lairetaM erusserP).xam(

erutarepmeT).nim().xam(

timilTxP

kcolraG,rab96,aPM9.6

isp0001C°402

)F°004(C°37–

)F°001–(000052

)ispxF°(

etihparG,rab52,aPM5.2

isp263C°083

)F°617(C°001–

)F°841–(

EFTP,rab06,aPM6

isp078C°052

)F°284(C°001–

)F°841–(


16

BASIC ORDERING INFORMATION model S264A Flanged Remote Seal (flush and extended)Select one character or set of characters from each category and specify complete catalog number.

LEDOMESAB 1– ts 5ot ht sretcarahc S 2 6 4 A X X X X X X X X X X d'tnoC

5.61BEMSAot)dednetxednahsulf(laesetomeRdegnalF

–noitcennocfoedisrettimsnarT 6 ht retcarahc

edishgiHediswoL

HL

egnalfgnitnuoM 7– ht retcarahc

gnitatoR R


ni2ni3ni4

CDE

gnitaR – 9 ht retcarahc

051LCEMSA003LCEMSA006LCEMSA009LCEMSA

0051LCEMSA

)ezisni4htiwelbaliavatoN()ezisni4htiwelbaliavatoN()ezisni4htiwelbaliavatoN(


12345

lairetamegnalfgnitnuoM 01– ht retcarahc

leetsnobraCss613ISIA

AB






)2etoN()2etoN()2etoN()2etoN()2etoN()2etoN(

F123456



)smgarhpaiddednetxerofton(-™0002CyolletsaH)smgarhpaiddednetxerofton(-526lenocnI

)smgarhpaiddednetxerofton(-mulatnaT)smgarhpaiddednetxerofton(-detalpdlogssL613ISIA



)smgarhpaiddednetxerofton(-)974ASMTSAot05723SSNU(ssxelpudrepuS

)3etoN(

)4etoN()4etoN()4etoN()4etoN()3etoN(


ECANECANECANECAN

ECANECANECAN

SHMLTNKYWFE

hsinifecafruslaeS 31– ht retcarahc

detarreShtoomS

)5,3setoN( 12





)3(1)5(5.1

)7(2)8(5.2)01(3

)21(5.3)31(4

)51(5.4)71(5

)81(5.5)02(6

)22(5.6)32(7

)52(5.7)72(8)03(9

)33(01)04(21)74(41)35(61



17

Note 1: Not available with size code E

Note 2: Not available with mounting flange rating code 3, 4, 5

Note 3: Not available with extensions length and material code 2, 4, 6

Note 4: Not available with extensions length and material code 1, 2, 3, 4, 5, 6

Note 5: Not available with diaphragm material code M, L, T, N, K, Y, W and H when selected with extension length and material code F, 2, 4, 6



Note 8: Not available with Flushing ring: hole and thread code 2, 3, 4, 5

Note 9: Not available with Flushing ring: hole and thread code N

Note 10: Not available with seal surface finish code 1 (serrated)



A462SNOITAMROFNIGNIREDROCISAB X X X X X






)6etoN()6etoN(


SNDHCWAB


enoN 1


)SNOISREVDEDNETXEROFDETCELESEBOT(enoNTPNni2/1-eloh1TPNni2/1-seloh2


)4etoN()4etoN()4etoN()4etoN(

N2345


enoNssL613ISIA

672CyolletsaH

)8etoN()9etoN(

)01,9setoN(ECANECAN

NAH










NABCDEFGHLMP


18

BASIC ORDERING INFORMATION model S264E Flanged Remote Seal (flush and extended)Select one character or set of characters from each category and specify complete catalog number.

LEDOMESAB 1– ts 5ot ht sretcarahc S 2 6 4 E X X X X X X X X X X d'tnoC

1-2901NEot)dednetxednahsulf(laesetomeRdegnalF


edishgiHediswoL

HL


gnitatoR R


05ND08ND

001ND

CDE


61NP04NP36NP

001NP)ezis001NDroftoN()ezis001NDroftoN(

)1etoN()1etoN(

1234



AB






)2etoN()2etoN()2etoN()2etoN()2etoN()2etoN(

F123456



)mgarhpaiddednetxerofton(-™0002CyolletsaH)mgarhpaiddednetxerofton(-526lenocnI

)mgarhpaiddednetxerofton(-mulatnaT)mgarhpaiddednetxerofton(-detalpdlogssL613ISIA

gnitaockcits-itnahtiwssL613ISIAgnitaockcits-itnahtiw™672CyolletsaH


)mgarhpaiddednetxerofton(-)974ASMTSAot05723SSNU(ssxelpudrepuS

)3etoN(

)4etoN()4etoN(

)4etoN()3etoN(


ECANECANECANECAN

ECANECANECAN

SHMLTNKYWFE


detarreShtoomS

)5,3setoN( 12





)3(1)5(5.1

)7(2)8(5.2)01(3

)21(5.3)31(4

)51(5.4)71(5

)81(5.5)02(6

)22(5.6)32(7

)52(5.7)72(8)03(9

)33(01)04(21)74(41)35(61



19

Note 1: Not available with size code E

Note 2: Not available with mounting flange rating code 3, 4

Note 3: Not available with extensions length and material code 2, 4, 6

Note 4: Not available with extensions length and material code 1, 2, 3, 4, 5, 6

Note 5: Not available with diaphragm material code M, L, T, N, K, Y, W and H when selected with extension length and material code F, 2, 4, 6



Note 8: Not available with Flushing ring: hole and thread code 2, 3, 4, 5

Note 9: Not available with Flushing ring: hole and thread code N

Note 10: Not available with seat surface finish code 1 (serrated)



E462SNOITAMROFNIGNIREDROCISAB X X X X X






)6etoN()6etoN(


SNDHCWAB


enoN 1


)SNOISREVDEDNETXEROFDETCELESEBOT(enoNTPNni2/1-eloh1TPNni2/1-seloh2



N2345


enoNssL613ISIA

672CyolletsaH

)8etoN()9etoN(

)01,9setoN(ECANECAN

NAH










NABCDEFGHLMP


20

S264G Model Flanged Flush Diaphragm Remote Seal to JISThis model identifies a diaphragm remote seal designed to connect to flanged pipe fitting, according to JIS standards.For liquid level measurement installations, the seal connects to an JIS flanged tank nozzle. The sealing is provided by a selectablesmooth or serrated gasket seat surface finish.


158 (6.22)

B

F G

C

E

A D




)aid(B )aid(B )aid(B )aid(B )aid(B )aid(C )aid(C )aid(C )aid(C )aid(C )aid(D )aid(D )aid(D )aid(D )aid(D )aid(E )aid(E )aid(E )aid(E )aid(E FFFFF GGGGG

K01ssalC05AK02ssalC05AK04ssalC05AK01ssalC08AK02ssalC08AK04ssalC08AK01ssalC001AK02ssalC001A

)63.2(06)63.2(06)63.2(06

)5.3(98)5.3(98)5.3(98)5.3(98)5.3(98

)87.3(69)87.3(69

)11.4(3.401)69.4(621

)2.5(231)94.5(4.931

)49.5(151)3.6(061

)27.4(021)27.4(021)21.5(031)19.5(051

)3.6(061)96.6(071)98.6(571)82.7(581

)1.6(551)1.6(551)5.6(561)82.7(581)78.7(002)72.8(012)72.8(012)68.8(522

)95.0(51)57.0(91)57.0(91)95.0(51)19.0(32)19.0(32)57.0(91)19.0(32

)36.0(61)17.0(81)20.1(62)17.0(81)78.0(22)62.1(23)17.0(81)49.0(42

)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9

44888888


21


The pressure limit decreases with increasing temperature above120°C according to JIS B 2220 standards.

Vacuum Service


Minimum pressure with tantalum diaphragm is 1kPa abs,10mbar abs, 0.15psia.







Gasket seat finish

Smooth : 0.8µm (Ra)

Serrated : 3.2 to 6.3µm (Ra)

Temperature effect








ssalC/gnitaR0222BSIJot

leetSnobraCC°021@


K01 rab41 rab41

K02 rab63 rab63

K04 rab86 rab86



05A Hni61.1,rabm9.2,aPk92.0 2O Hni82.0,rabm7.0,aPk70.0 2O Hni8.0,rabm2,aPk2.0 2O

08A Hni63.0,rabm9.0,aPk90.0 2O Hni21.0,rabm3.0,aPk30.0 2O Hni21.0,rabm3.0,aPk30.0 2O

001A Hni63.0,rabm9.0,aPk90.0 2O Hni21.0,rabm3.0,aPk30.0 2O Hni21.0,rabm3.0,aPk30.0 2O


22

BASIC ORDERING INFORMATION model S264G Flanged Flush Remote Seal to JISSelect one character or set of characters from each category and specify complete catalog number.

LEDOMESAB 1– ts 5ot ht sretcarahc S 2 6 4 G X X X X X X X X X X d'tnoC

SIJotlaesetomeRhsulFdegnalF


edishgiHediswoL

HL


gnitatoR R


05A08A001A

BCD


K01K02K04 )1etoN(

246



AB


)lairetammgarhpaidroftxenees(hsulF F


ssL613ISIA™672CyolletsaH™0002CyolletsaH

526lenocnImulatnaT

detalpdlogssL613ISIAgnitaockcits–itnahtiwssL613ISIA

gnitaockcits–itnahtiw™672CyolletsaHgnitaockcits-itnadnanoisorroc-itnahtiwssL613ISIA

)974ASMTSAot05723SSNU(ssxelpudrepuS

ECANECANECANECAN

ECANECANECANECANECAN

SHMLTNKYWE


detarreShtoomS

)2etoN( 12





)3(1)5(5.1

)7(2)8(5.2)01(3

)21(5.3)31(4

)51(5.4)71(5

)81(5.5)02(6

)22(5.6)32(7

)52(5.7)72(8)03(9)33(01)04(21)74(41)35(61



23

Note 1: Not available with A100 size code D

Note 2: Not available with diaphragm material code H, M, L, T, N, K, Y, W



G462SNOITAMROFNIGNIREDROCISAB X X X X X






)3etoN()3etoN(


SNDHCWAB


enoN 1


enoN N


enoN N


teksagon-gulpoN N


24

This flush diaphragm remote seal is designed to connect to ASME flanged pipe fitting, the sealing is provided by a metal ring in theprovided groove. For liquid level measurement installations the seal connects to an ASME flanged tank nozzle (Schedule 40).


158 (6.22)

B

F G

C

E

A DH


)ni(mmsnoisnemiD )ni(mmsnoisnemiD )ni(mmsnoisnemiD )ni(mmsnoisnemiD )ni(mmsnoisnemiD

RRRRRfo°N fo°N fo°N fo°N fo°Nseloh seloh seloh seloh seloh

)aid(A )aid(A )aid(A )aid(A )aid(A )aid(B )aid(B )aid(B )aid(B )aid(B )aid(C )aid(C )aid(C )aid(C )aid(C )aid(D )aid(D )aid(D )aid(D )aid(D )aid(E )aid(E )aid(E )aid(E )aid(E FFFFF GGGGG )aid(H )aid(H )aid(H )aid(H )aid(H

051LCEMSAni2/1-1003LCEMSAni2/1-1006LCEMSAni2/1-1

0051/009LCEMSAni2/1-10052LCEMSAni2/1-1

051LCEMSAni2003LCEMSAni2006LCEMSAni2

0051/009LCEMSAni20052LCEMSAni2

051LCEMSAni3003LCEMSAni3006LCEMSAni3009LCEMSAni30051LCEMSAni30052LCEMSAni3

)98.1(84)98.1(84)98.1(84)98.1(84)98.1(84)63.2(06)63.2(06)63.2(06)63.2(06)63.2(06

)5.3(98)5.3(98)5.3(98)5.3(98)5.3(98)5.3(98

)72.3(38)45.3(09)45.3(09)26.3(29)94.4(411)20.4(201)52.4(801)52.4(801)88.4(421)42.5(331)42.5(331)57.5(641)57.5(641)01.6(551)16.6(861)16.6(861

)88.3(6.89)5.4(3.411)5.4(3.411

)88.4(421)57.5(1.641)57.4(56.021

)5(721)5(721

)5.6(561)57.6(5.171

)6(4.251)26.6(51.861)26.6(51.861

)5.7(5.091)8(2.302)9(6.822

)5(721)21.6(5.551)21.6(5.551

)7(8.771)8(2.302)6(4.251

)5.6(1.561)5.6(1.561)5.8(9.512

)52.9(532)5.7(5.091

)52.8(55.902)52.8(55.902

)5.9(3.142)5.01(7.662

)21(8.403

)26.0(57.51)88.0(53.22)88.0(53.22)21.1(54.82)52.1(57.13)57.0(50.91)57.0(50.91)57.0(50.91

)1(4.52)21.1(54.82)57.0(50.91)88.0(53.22)88.0(53.22

)1(4.52)52.1(57.13)83.1(50.53

)96.0(5.71)18.0(6.02)88.0(4.22)52.1(8.13)57.1(5.44)57.0(50.91)88.0(53.22

)1(4.52)5.1(1.83

)2(8.05)49.0(78.32)21.1(44.82)52.1(57.13

)05.1(1.83)88.1(8.74)26.2(5.66

)86.0(3.71)86.0(3.71)86.0(3.71)28.0(8.02)28.0(8.02)86.0(3.71)86.0(3.71)86.0(3.71)28.0(8.02)28.0(8.02)86.0(3.71)86.0(3.71)86.0(3.71)28.0(8.02)28.0(8.02)28.0(8.02

)65.2(1.56)96.2(3.86)96.2(3.86)96.2(3.86)52.3(6.28)52.3(6.28)52.3(6.28)52.3(6.28)57.3(3.59

)4(6.101)5.4(3.411)78.4(8.321)78.4(8.321)78.4(8.321)73.5(5.631

)5(721

91R02R02R02R32R22R32R32R42R62R92R13R13R13R53R23R

4444448888488888

S264R Model Flanged Flush Diaphragm Remote Seal - Ring Joint


25



Flanged Flush Diaphragm Remote Seal - Ring Joint










Vacuum Service




Temperature effect








hsulFdegnalFmgarhpaiD

eziSlaeStnioJgniRrorrelaeS rorrEyrallipaCm1 rorrE)rosneS(metsyS

1 1/2 ni Hni5.3,rabm7.8,aPk78.0 2O Hni2.1,rabm3,aPk3.0 2O Hni6.3,rabm9,aPk9.0 2O

ni2 Hni61.1,rabm9.2,aPk92.0 2O Hni82.0,rabm7.0,aPk70.0 2O Hni8.0,rabm2,aPk2.0 2O



26

BASIC ORDERING INFORMATION model S264R Flanged Remote Seal - Ring JointSelect one character or set of characters from each category and specify complete catalog number.

LEDOMESAB 1– ts 5ot ht sretcarahc S 2 6 4 R X X X X X X X X X X d'tnoC

5.61BEMSAottniojgniRlaesetomeRdegnalF


edishgiHediswoL

HL


gnitatoR R


ni2/1-1ni2ni3

BCD


051LCEMSA003LCEMSA006LCEMSA009LCEMSA

0051LCEMSA0052LCEMSA

123456



AB


)lairetammgarhpaidroftxenees(hsulF F



526lenocnI

ECANECANECAN

SHL


tniojgniR 3





)3(1)5(5.1

)7(2)8(5.2)01(3

)21(5.3)31(4

)51(5.4)71(5

)81(5.5)02(6

)22(5.6)32(7

)52(5.7)72(8)03(9

)33(01)04(21)74(41)35(61



27



R462SNOITAMROFNIGNIREDROCISAB X X X X X






)1etoN()1etoN(


SNDHCWAB


enoN 1


dettiftoN N


enoN N


enoN N


28

S264T Model Off-line Threaded Connection Remote SealThe off-line threaded connection remote seals are designed to connect directly to a process pipe via the NPT connection in the lowerhousing . These elements are available with a flushing connection, on request, in the lower housing.


16 MPa, 160 bar, 2320 psi @ 20°C (68°F)

The pressure limit decreases with increasing temperature above 20°C(68°F)

Vacuum Service





260°C (500°F) for Tantalum diaphragm

320°C (608°F) for AISI gold plated diaphragm


–20°C (-4°F) to 200°C (392°F) with Viton gasket

360°C (680°F) with Graphite gasket

Mounting flange

AISI 316 L ss, Hastelloy C

Gasket (flange to seal)

Viton, PTFE, Graphite

Bolts

AISI 316 ss bolts Class A4-80 and nuts Class A4-70 per EN ISO3506;Carbon steel bolts Class 8.8 per EN ISO 4014 and nuts Class 8 perEN ISO 898/2;Alloy steel bolts per ASTM-A-193-77a grade B7M and nuts perASTM A194/A 194 M-90 grade 2HM, in compliance with NACEMR0175 Class II.

Temperature effect








Gasket

DiaphragmProcess

Connection

Lower Housing

1/4in NPT-fFlushing connection

(option)

dedaerhTeniL-ffOeziSlaeS


2 1/2 ni Hni82.1,rabm2.3,aPk23.0 2O Hni27.0,rabm8.1,aPk81.0 2O Hni6.0,rabm5.1,aPk51.0 2O

Q

D

134

(5.3

) eziS)ni(mmsnoisnemiD

)aid(D Q

1/4 TPNni )3.4(2.901 )1.2(3.35

1/2 TPNni )3.4(2.901 )1.2(3.35

3/4 TPNni )3.4(2.901 )5.2(5.36

TPNni1 )3.4(2.901 )5.2(5.36

1 1/2 TPNni )3.4(2.901 )5.2(5.36


29

BASIC ORDERING INFORMATION model S264T Off-Line Threaded Connection Remote Seal



Note 3: Not available with Size code 4

Select one character or set of characters from each category and specify complete catalog number.LEDOMESAB 1– ts 5ot ht sretcarahc S 2 6 4 T X X X X X X X X X X

laesetomerdedaerhtenil-ffO


HL

eziS 7– ht retcarahc1/4 f-TPNni1/2 f-TPNni3/4 f-TPNni

f-TPNni1-1 1/2 f-TPNni

12534

stloB – 8 ht retcarahc

ss613ISIAleetsnobraC

leetsyollA ECAN

123

lairetamegnalF 9– ht retcarahc


ECANECAN

12





ECANECANECANECAN

SHMLTN





)3(1)5(5.1

)7(2)8(5.2)01(3

)21(5.3)31(4

)51(5.4)71(5

)81(5.5)02(6

)22(5.6)32(7

)52(5.7)72(8)03(9

ABCDEFGHJKLMNPQR






)1etoN()1etoN(


SNDHCWAB

snoitcennocgnihsulF 41– ht retcarahc

deriuqertoNdedivorP )3etoN(

1Q


EFTP™notiV

etihparG

237


30

The off-line flanged connection remote seals are designed toconnect directly to ASME or EN flanged tank nozzles.These elements are available with a flushing connection in thelower housing, selectable on request in the ordering code.


Class 150 to ASME B16.5: 230psi @ 100°F (38°C)

Class 300 to ASME B16.5: 600psi @ 100°F (38°C)

PN16-40 to EN 1092-1: 34bar @ 20°C

The pressure limit decreases with increasing temperature above to thespecified values respectively for ASME B16.5 or EN 1092-1 std.

Vacuum Service





260°C (500°F) for Tantalum diaphragm

320°C (608°F) for AISI gold plated diaphragm


–20°C (-4°F) to 200°C (392°F) with Viton gasket

360°C (680°F) with Graphite gasket

Gasket seat finish (flange to process)

serrated (ASME): 3.2 to 6.3µm (Ra)

serrated (EN 1092-1 Type B1): 3.2 to 12.5µm (Ra)

Mounting flange

AISI 316 L ss, Hastelloy C

Gasket (flange to seal)

Viton, PTFE, Graphite

Bolts

bolts (seal/flange): AISI 316 ss Class A4-70 per EN ISO 3506;

studs with nuts (flange/process): AISI 3xx per ASTM-SA-193/194grade B8C or B8T

Temperature effect






For filling different from silicone oil (DC200) the errors can be multipliedby ratio between the thermal expansion coefficients of the selectedfilling divided by the one of DC200, listed in the fluid characteristics table.

THE ERRORS IN TABLE CAN BE CONSIDERED DIVIDED BY 4 FORTRANSMITTERS USING SAME REMOTE SEAL ON THE TWO SIDES.

1/4in NPT-fFlushing connections(2 opposite at 180°

as option)

GasketSeatfinish

degnalFeniL-ffOeziSlaeS

rorrelaeS rorrEyrallipaCm1rorrE)rosneS(metsyS

2 1/2 ni Hni82.1,rabm2.3,aPk23.0 2O Hni27.0,rabm8.1,aPk81.0 2O Hni6.0,rabm5.1,aPk51.0 2O

63.5

(2.5

)

dia 110 (4.33)

B

E

D

F

A

C

134

(5.3

)

S264M Model Off-line Flanged Connection Remote Seal

noitcennoC )ni(mmsnoisnemiD

eziS dradnatS )aid(A )aid(B)sduts4(C

)aid(D )aid(E FhtgneL daerhT

1/2 ni051LCEMSA )33.4(011 )83.2(5.06 )35.1(93 CNU31–ni2/1

)83.1(1.53 )26.0(8.51 )60.0(6.1003LCEMSA )33.4(011 )26.2(5.66 )35.1(93 CNU31–ni2/1

ni1051LCEMSA )33.4(011 )21.3(4.97 )35.1(93 CNU31–ni2/1

)2(8.05 )50.1(7.62 )60.0(6.1003LCEMSA )88.4(421 )5.3(9.88 )2(15 CNU11–ni8/5

1 1/2 ni051LCEMSA )5(721 )78.3(4.89 )35.1(93 CNU31–ni2/1

)78.2(37 )16.1(14 )60.0(6.1003LCEMSA )1.6(551 )5.4(3.411 )42.2(75 CNU01–ni4/3

52ND 04-61NPNE )25.4(511 )43.3(58 )56.1(24 21M )76.2(86 )21.1(5.82 )70.0(204ND 04-61NPNE )9.5(051 )33.4(011 )98.1(84 61M )64.3(88 )96.1(1.34 )21.0(3


31

BASIC ORDERING INFORMATION model S264M Off-line Flanged Connection Remote SealSelect one character or set of characters from each category and specify complete catalog number.

Note 1: Not available with EN mounting flange code M, N

Note 2: Not available with ASME mounting flange code A, B, C, D, 6, 7



LEDOMESAB 1– ts 5ot ht sretcarahc S 2 6 4 M X X X X X X X X X X

laesetomerdegnalf-inimenil-ffO


HL

egnalfgnitnuoM 7– ht retcarahclaeshtiwlargetnI P

gnitaregnalfgnitnuoM/eziS – 8 ht retcarahc

1/2 ni1/2 ni

ni1ni1

1 1/2 ni1 1/2 ni

52ND04ND

051LCEMSA003LCEMSA051LCEMSA003LCEMSA051LCEMSA003LCEMSA

04/61NPNE04/61NPNE

67ACBDMN

)laes(mroftaeS/egnalfgnitnuoM 9– ht retcarahc

ssL613ISIAssL613ISIA

™672CyolletsaH™672CyolletsaH

hsinifdetarres–)ecafdesiar(FRmroFhsinifdetarres–1BepyT1-2901NE

hsinifdetarres–)ecafdesiar(FRmroFhsinifdetarres–1BepyT1-2901NE


ECANECANECANECAN

DLUV





ECANECANECANECAN

SHMLTN





)3(1)5(5.1

)7(2)8(5.2)01(3

)21(5.3)31(4

)51(5.4)71(5

)81(5.5)02(6

)22(5.6)32(7

)52(5.7)72(8)03(9

ABCDEFGHJKLMNPQR






)3etoN()3etoN(


SNDHCWAB

snoitcennocgnihsulF 41– ht retcarahc

deriuqertoNdedivorP

1Q


EFTP™notiV

etihparG

237


32

S264U Model Union Connection Remote Seal (To be used only for gauge pressure)The union connection remote seal are used exclusively for pressure measurement with gauge pressure transmitter.The seal is available with an optional weld bushing, or with an optional chemical tee flange.The remote seal with a weld bushing,includes a bushing which provides the mating surface for the seal element. The union connection seal with a chemical tee flange, isdesigned to connect to any process fitting which accepts a chemical tee seal element (refer to Chemical Tee Seal for more information).The union seal connects to the chemical tee flange which serves as an adaptor to permit connection of the union seal to a chemical teetype fitting.


Union Connection: 10.3 MPa, 103 bar, 1500 psi

With Chemical Tee Flange : 2 MPa, 20 bar, 300 psi

Vacuum Service


Refer to table A.


Same as fill fluid limits.

Refer to table A.

–50°C (–58°F) to 204°C (400°F) with silicone rubber gasket


Temperature effect








DiaphragmSurface

WeldingBushing



UnionConnection Seal

UnionConnection

DiaphragmSurface

Chemical TeeFlange

O-Ring

noitcennoCnoinUeziSlaeS


1 1/2 ni Hni5.3,rabm7.8,aPk78.0 2O Hni2.1,rabm3,aPk3.0 2O Hni6.3,rabm9,aPk9.0 2O

Union Connection Seal without weld bushing

Union Connection Sealwith chemical tee flange

Union Connection Sealwith weld bushing

120 (4.7) 25 (1)

dia

42 (1

.65)

dia

89 (3

.5)

UnionConnection

57 (2.25)

120 (4.7) 25 (1)

12 (0.47)

dia

96 (3

.78)

dia

42 (1

.65)

dia

127

(5)

8 Mounting Holes dia 8.7 (0.34)Equally Spaced on 111.125 (4.37)

Bolt Circle

dia

41 (1

.61)

dia

42 (1

.65)

dia

51 (2

) 29 (1.14)

134 (5.3)

16 (0.63)

9 (0.35)14 (0.55)

45°

5 (0.19)

5 (0.19)

4 (0.16)

dia

42 (1

.65)

2 (0.08)

54 (2.12) - 16N210 (0.39) Full Thread


33

BASIC ORDERING INFORMATION model S264U Union Connection Remote SealSelect one character or set of characters from each category and specify complete catalog number.



LEDOMESAB 1– ts 5ot ht sretcarahc S 2 6 4 U X X X X X X X X

)RETTIMSNARTHCAEROFYLNOENOEBTSUM(laesetomernoitcennocnoinU


HL

eziS 7– ht retcarahc1 1/2 ni L



ECANECAN

SH





)3(1)5(5.1

)7(2)8(5.2

)01(3

ABCDE






)1etoN()1etoN(


SNDHCWAB

snoitpO 21– ht retcarahc

enoNgnihsubdlewss613ISIA

egnalfeetlacimehC

134


rebburenociliSEFTP

58


34

S264S Food and Sanitary Remote SealsThe Union Nut and Triclamp remote seals are designed for connection by Union Nut according to DIN 11851 - F50 or F80 and 2 in,3 in, 4 in Triclamp sanitary fittings. A variety of gaskets and clamp rings for the seals are available.

pmalcirT

ni2 ni3 ni4

)aid(A )2.2(3.65 )62.3(38 )43.4(3.011

)aid(B )5.2(46 )85.3(19 86.4(911

Union Nut Seal (to DIN 11851)

Triclamp Seal

The Cherry Burrell remote seals are designed for connection to 2in, 3in or 4in Cherry Burrell I-Line sanitary fittings.A 4in V-band clamp is optionally available for the 4in variant.

tuNnoinU

05F 08F

)aid(A )86.2(86 )39.3(001

)DR(B )70.3(87 )33.4(011

C )36.0(61 )47.0(91

A

B

C13

4 (5

.3)

27 (1

.06)A

B

20

(0.7

9)

2.8

5 (0

.11)

134

(5.3

)

E

FH

G

B

A

C

D

eziS)ni(mmSNOISNEMID

)aid(A )aid(B )aid(C )aid(D E F G H

ni2 )46.2(76 )2.2(65 )56.1(24 )42.2(75 )31.0(2.3 )62.0(5.6 )94.0(5.21 )21.0(3

ni3 )78.3(4.89 )91.3(18 )58.2(24.27 )3.3(8.38 )90.0(4.2 )13.0(9.7 )95.0(51 )21.0(3

ni4 )88.4(421 )83.4(52.111 )58.2(24.27 )3.4(3.901 90.0(4.2 )13.0(9.7 )95.0(51 )21.0(3

Note: seal model not3-A authorized


35

The sanitary remote seal with flush diaphragm is designed to connect to a 4in sanitary tank spud. The tank spud and process gasketare available as options with the seal suitable V-band clamp is also available on request.NOTE: The tank spud required for connection of this seal element must be welded to the process vessel prior to connecting the seal,following a recommended welding and pressure testing procedure.

The sanitary remote seal with extended diaphragm is designed to connect to a 4in sanitary tank spud. The tank spud and processgasket are available with the seal.NOTE: The tank spud required for connection of this seal element must be welded to the process vessel prior to connecting the seal,following a recommended welding and pressure testing procedure.

eziS)ni(mmsnoisnemiD

A

ni2 )1.2(3.35

ni4 )1.4(1.401

ni6 )1.6(9.451

dia 72 (2.83)

dia 110 (4.33)

dia 152.4 (6)

19.3

(0.7

5)

18.5

(0.7

2)

8 (0

.31)

for

thin

wal

l

13 (0

.51)

for

thic

k w

all

dia 119 (4.68)

dia 85.5 (3.36)dia 36 (1.41)

dia 72 (2.83)dia 100 (3.93)dia 152 (5.98)

A10

(0.3

9)

5.6

(0.2

2)

dia 132.6 (5.22)


36

The sanitary aseptic remote seal is designed to connect to a 4in sanitary fitting: either an aseptic tank spud or a 4in Cherry Burrellaseptic ferrule. The tank spud, gaskets and V-band clamp are available option with the seal element.NOTE: The tank spud or ferrule required for connection of this seal element must be welded to the process vessel prior toconnecting the element, following recommended welding and pressure testing procedure. Weld the Cherry Burrell ferrule to theprocess vessel in accordance with manufacturers recommandations.

4in Aseptic Flanged Connection

4in Cherry Burrell Aseptic

Maximum Working Pressure @ 20°C (68°F)

2 in Triclamp : 3.8 MPa, 38 bar, 550 psi



F50/F80 Union nut : 2.5 MPa, 25 bar, 360 psi

Cherry Burrell: 1.9MPa, 19bar, 275psi

4in Sanitary flush or extended or aseptic: 1.9MPa, 19bar, 275psi

4in V-band clamp option: 1MPa, 10bar, 145psi

4in schedule 5 V-band clamp option: 0.7MPa, 7bar, 100psi @ 21°C.



Process Gasket Temperature Limits

Ethylene Propylene EPDM 3-A 18-03 Class II:–40 to 121°C (–40 to 250°F)

Ethylene Propylene: –40 to149°C (–40 to 300°F)

Vacuum Service


Temperature effect








,llerruByrrehC,pmalcirT,tuNnoinUeziSlaeScitpesAdnayratinaS


05F/ni2 Hn8.2,rabm7,aPk7.0 2O Hni7.1,rabm2.4,aPk24.0 2O Hni6.5,rabm41,aPk4.1 2O

08F/ni3 Hni42.0,rabm6.0,aPk60.0 2O Hni21.0,rabm3.0,aPk30.0 2O Hni21.0,rabm3.0,aPk30.0 2O


2 holes 1/8in–27NPT(180° symmetrical for steam connection)

dia 119 (4.68)

dia 105 (4.13)

dia 85.5 (3.36)

dia 79.6 (3.13)dia 62 (2.44)

4.2

(0.1

6)

19.3

(0.7

5)

11.2

(0.7

5)

dia 72.4 (2.85)

dia 82.6 (3.25)

dia 111.25 (4.37)

dia 124 (4.88)

2.4

(0.0

9)

7.9

(0.3

1)3

(0.1

1)

15 (0

.59)


37

BASIC ORDERING INFORMATION model S264S Food and Sanitary Remote SealsSelect one character or set of characters from each category and specify complete catalog number.

Note 1: Union nut DIN 11851 (F50 and F80) are not 3-A authorized models


LEDOMESAB 1– ts 5ot ht sretcarahc S 2 6 4 S X X X X X X X X

slaesetomeryratinaSdnadooF


HL

noitcennocgnitnuoM 7– ht retcarahc05F–15811NIDtunnoinU08F–15811NIDtunnoinU

pmalcirTni2pmalcirTni3pmalcirTni4

llerruByrrehCni2llerruByrrehCni3llerruByrrehCni4

mgarhpaidhsulfyratinaSni4mgarhpaid)ni2(dednetxeyratinaSni4mgarhpaid)ni4(dednetxeyratinaSni4mgarhpaid)ni6(dednetxeyratinaSni4

citpesallerruByrrehCni4noitcennocdegnalfcitpesani4

)1etoN()1etoN(

ABFGHLMNPQRSWJ

lairetammgarhpaidlaeS – 8 ht retcarahc

ssL613ISIA S





)3(1)5(5.1

)7(2)8(5.2

)01(3)21(5.3

)31(4)51(5.4

)71(5)81(5.5

)02(6)22(5.6

)32(7)52(5.7

)72(8)03(9

)33(01

ABCDEFGHJKLMNPQRS


lioenociliS)devorppaADF(liolareniM



SWAB

sgnittiF/pmalC 21– ht retcarahc

enoN)pmalcirTni2rof(pmalCdnab-Vni2)pmalcirTni3rof(pmalCdnab-Vni3

)degnalfcitpesani4dnahsulfyratinaSni4,llerruByrrehCni4,pmalcirTni4rof(pmalCdnab-Vni4)laeshsulfyratinaSni4rof(pmalCdnab-Vni4dna)81.0(mm7.4otpullawknat,dupsknaTni4)laeshsulfyratinaSni4rof(pmalCdnab-Vni4dna)73.0(mm5.9otpullawknat,dupsknaTni4

)laesdednetxeyratinaSni4rof(pmalcdnab-V5eludehcsni4)laesni2dednetxeyratinaSni4rof(pmalcdnab-V5eludehcsni4dnanoisnetxeni2rofdupsknaT)laesni4dednetxeyratinaSni4rof(pmalcdnab-V5eludehcsni4dnanoisnetxeni4rofdupsknaT)laesni6dednetxeyratinaSni4rof(pmalcdnab-V5eludehcsni4dnanoisnetxeni6rofdupsknaT

)laesdegnalfcitpesani4rof(dupsknatcitpesA

1ABCDEFGHJP


enoN)IIssalC30-81A-3MDPE(-)laesdednetxeyratinaSni4rof(001NDteksagenelyporpenelyhtE

)laestunnoinU05Frof(05NDteksagenelyporpenelyhtE)laestunnoinU08Frof(08NDteksagenelyporpenelyhtE

)IIssalC30-81A-3MDPE(-)laesdegnalfcitpesadnahsulfyratinasni4rof(teksagenelyporpenelyhtE

1ACDG


38

S264P Remote seal(s) for Urea Service

Maximum Working Pressure @ 20°C (68°F)

3in, ASME 600 flange:

- 8 MPa, 80 bar, 1160 psi

2in ASME 2500 threaded flange:

- 32 MPa, 320 bar, 4640 psi

Vacuum Service




Temperature effect








Flange ASME 600, 3in Threaded Flange ASME 2500, 2in

ecivreSaerUeziSlaeSdegnalF


1 1/2 ni Hni6.5,rabm41,aPk4.1 2O Hni42.2,rabm6.5,aPk65.0 2O Hni2.7,rabm81,aPk8.1 2O

2 1/2 ni Hni88.0,rabm2.2,aPk22.0 2O Hni4.0,rabm1,aPk1.0 2O Hni63.0,rabm9.0,aPk90.0 2O

131

(5.1

6)45

(1.7

7)

dia 155 (6.10)

no. 4 holesdia 25.4 (1)

dia 53(2.08)

dia37.5(1.47)

~15

(0.5

9)

dia 110 (4.33)

dia 60(2.36)

2(0.07) ANSI B2.1 NPS

69 or 94(2.71 or 3.7)

69(2.71)

dia 127 (5)

3.5

(0.1

4)

31.8

(1.2

5)

6.4

(0.2

5)

40.3

(1.

59)

dia 168.3 (6.63)

dia 209.6 (8.25)

no. 8 holesdia 22.2 (0.87)


39

BASIC ORDERING INFORMATION model S264P Remote Seal for Urea ServiceSelect one character or set of characters from each category and specify complete catalog number.

Note 1: Not available with Size/Mounting flange code J

Note 2: Not available with Size/Mounting flange code H

LEDOMESAB 1– ts 5ot ht sretcarahc S 2 6 4 P X X X X X X X X

ecivreSaerUroflaesetomeR


HL

lairetaM/gnitargnitnuoM/eziS 7– ht retcarahcni3ni2

FR006EMSAegnalfdedaerhT

edarGaerUssL613ISIAleetsnobraC

HJ

retemaiD/htgnelnoisnetxE – 8 ht retcarahc

)ni95.1(mm3.04)ni95.1(mm3.04

)ni61.5(mm131

ni7.2(mm96)ni17.3(mm49

)ni74.1(mm5.73


RST


edarGaerUssL613ISIA S





)3(1)5(5.1

)7(2)8(5.2

)01(3)21(5.3

)31(4)51(5.4

)71(5)81(5.5

)02(6

ABCDEFGHJKL


lioenociliSerutarepmethgihroflioenocilIS

SH

noitpO 31– ht retcarahc

enoNtsetyeuH

13


40

S264B Model Button Type Remote Seal (To be used only for gauge pressure)These remote seals are designed to connect directly to a process pipe via the NPT threaded connection or to match pipe fitting withan interface suitable for the provided mating flange. The button seals, due to their design, are dedicated for measurement with medium/high calibrated span (2 MPa/20 bar/290 psi approx. or greater).

3 1/4in flange extended - type 91

3 1/2in flange extended - type 91 modified

1 1/2in threaded uniontype 92/92 modified

Flange

Spacer

Flange Spacer

6.35 (1/4)

13.49 (17/32)

19 (3/4)

2.3 (3/32)Thick Gasket

146 (5-3/4)

dia

83 (3

-1/4

)

4 Holes equally spaced33/64in dia on2-1/8in dia Bolt Circle

2 Holes5/16-18NC–2 on2-1/8in Dia Bolt Circle

51 (2)

dia 24 (15/16)dia 23 (59/64)

dia

35 (1

-3/8

)di

a 34

(1-2

3/64

)

dia 24 (15/16)dia 23 (59/64)

6.35 (1/4)

13.49 (17/32)

128 (5-1/32)25 (1)


212 (8-11/32) Max

dia

89 (3

-1/2

)

4 Holes equally spaced17/32in dia on2-1/2in dia Bolt Circle

2 Holes1/2-13NC–2 on2-1/2in Dia Bolt Circle

dia

35 (1

-3/8

)di

a 34

(1-2

3/64

)

dia 24 (15/16)dia 23 (59/64)

19 (3/4) 38 (1-1/2)

146 (5-3/4)


dia

24 (1

5/16

)di

a 23

(59/

64)

76 (3) 6.35 (1/4)

13.49 (17/32)

1-1/2 16N-2 for Type 921-1/2 12FG for Type 92 modified


41

Maximum Working Pressure (20 to 120°C; 68 to 248°F)

Types 89, 90 and 92: 42MPa, 420bar, 6090psi

Types 91: 35MPa, 350bar, 5075psi

Vacuum Service


Refer to table A.



Temperature effect





referred to silicone oil for high temperature filling and Hastelloy C276diaphragm materials.

epyTnottuBeziSlaeS


ni1 Hni23,rabm08,aPk8 2O Hni27,rabm81,aPk8.1 2O Hni8.21,rabm23,aPk2.3 2O


Bracket – type 89

Universal– type 90

dia 24 (15/16)dia 23 (59/64)

13.49 (17/32)

28.58 (1-1/8) 2.3 (3/32)Thick Gasket

dia 33.34 (1-5/16 )

6.35 (1/4)

125.41 (4-15/16)

138.

11 (5

-7/1

6)

dia 22.23 (7/8)

95.25 (3-3/4)

60.33 (2-3/8)

47.6 (1-7/8) 30.16 (1-3/16)

21.4

3 (2

7/32

)

42.8

6 (1

-11/

16)

2 Holesdia 17.46 (11/16)

6.35 (1/4)

13 (17/32)

78 (3-1/16)

52 (2-1/16)

146 (5-3/4)


dia 24 (15/16)dia 23 (59/64)


42

BASIC ORDERING INFORMATION model S264B Button Type Remote SealSelect one character or set of characters from each category and specify complete catalog number.

Note 1: Only available with Bracket type 89 version and suitable for food application

LEDOMESAB 1– ts 5ot ht sretcarahc S 2 6 4 B X X X X X X X X X

)RETTIMSNARTHCAEROFYLNOENOEBTSUM(laesetomerepytnottuB


HL

eziS 7– ht retcarahcni1 M

epytnoitcennocgnitnuoM – 8 ht retcarahc

3 1/4 19epyt–dednetxeegnalfni3 1/2 deifidom19epyt–dednetxeegnalfni1 1/2 29epyt–noinudedaerht2-N61ni1 1/2 deifidom29epyt–noinudedaerhtFN21ni

98epyt–tekcarB09epyt–lasrevinU

ABCFDE


™672CyolletsaH H





)3(1)5(5.1

)7(2)8(5.2)01(3

ABCDE


lioenociliSerutarepmethgihroflioenocilIS

)devorppaADF(liolareniM )1etoN(

SHW

noitpO 31– ht retcarahc

deriuqertoN)98epytrofton(ssecorproflavomerlaesrofralloctuokcaJ

12


enoNmuinimulA

ss613ISIA

1EF


43

™ Hastelloy C276 is a Cabot Corporation trademark

™ Hastelloy C2000 is an Haynes International trademark

™ Monel is an International Nickel Co. trademark

™ Viton is a Dupont de Nemour trademark

™ DC200 is a Dow Corning Corporation trademark

™ Galden is a Montefluos trademark

™ Halocarbon is a Halocarbon Products Co. trademark

™ AN140 is a Wacker-Chemie trademark

™ Neobee M20 is a Stepan Company trademark

™ Marcol is a Esso Italiana trademark

™ Syltherm is a Dow Chemical Company trademark

2600T Pressure TransmittersModel S264

SS

/S26

4_8

ABB has Sales & Customer Supportexpertise in over 100 countries worldwide

www.abb.com/instrumentation

The Company’s policy is one of continuous productimprovement and the right is reserved to modify the

information contained herein without notice.

Printed in Italy (12.2008)

© ABB 2008

ABB LtdHoward Road, St. NeotsCambridgeshire, PE19 8EUUKTel: +44(0)1480 475321Fax: +44(0)1480 217948

ABB Inc.125 E. County Line RoadWarminster, PA 18974USATel: +1 215 674 6000Fax: +1 215 674 7183

ABB SACEA division of ABB S.p.A.Via Statale 11322016 Lenno (CO) ItalyTel: +39 0344 58111Fax: +39 0344 56278

data sheet 2600t series pressure transmitters · 2018-05-10 · data sheet ss/s264_8 wide range of...

Documents