diy wine rack book ends - learn.kregtool.com
TRANSCRIPT
![Page 1: DIY Wine Rack Book Ends - learn.kregtool.com](https://reader031.vdocuments.net/reader031/viewer/2022013001/61ca76388d5fb001020ecabd/html5/thumbnails/1.jpg)
DIY Wine Rack Book Ends
What’s better than a wine rack? A wine rack that does more than just hold wine! Create this pair of multifunctional Wine
Rack Book Ends in just a few easy steps and for right under $20 in lumber!
Difficulty
Easy
Page 1 of 9
![Page 2: DIY Wine Rack Book Ends - learn.kregtool.com](https://reader031.vdocuments.net/reader031/viewer/2022013001/61ca76388d5fb001020ecabd/html5/thumbnails/2.jpg)
ToolsKreg Tools
Kreg Pocket-Hole Jig® 720
Other Tools
Miter Saw
Tape Measure
3.25 Inch Hole Saw
Drill (cordless)
Sander
MaterialsWood Products
Board , 1x6 , 48"1
Board , 1x10 , 48"1
Hardware & Supplies
Wood Stain1
1 1/4" Pocket Hole Screws8
Wood Glue1
Page 2 of 9
![Page 3: DIY Wine Rack Book Ends - learn.kregtool.com](https://reader031.vdocuments.net/reader031/viewer/2022013001/61ca76388d5fb001020ecabd/html5/thumbnails/3.jpg)
Cut List & PartsFaces , 10x10 (See Diagram)4
Back Panels , 10 X 6 (See Diagram)2
Bottom Panels , 9 1/4" X 6 (See Diagram)2
Page 3 of 9
![Page 4: DIY Wine Rack Book Ends - learn.kregtool.com](https://reader031.vdocuments.net/reader031/viewer/2022013001/61ca76388d5fb001020ecabd/html5/thumbnails/4.jpg)
DirectionsCheck Dimensions & Cut ListThe plans for this project outline the steps to make one of the two wine holders in the set. To make a set of two, be sure to
follow all steps twice. Check all dimensions and the cut list before starting.
1
Page 4 of 9
![Page 5: DIY Wine Rack Book Ends - learn.kregtool.com](https://reader031.vdocuments.net/reader031/viewer/2022013001/61ca76388d5fb001020ecabd/html5/thumbnails/5.jpg)
Create HolesDrill holes into all of the faces of your wine racks using a 3 1/2" hole saw. Use a ruler to find the center of each face.2
Page 5 of 9
![Page 6: DIY Wine Rack Book Ends - learn.kregtool.com](https://reader031.vdocuments.net/reader031/viewer/2022013001/61ca76388d5fb001020ecabd/html5/thumbnails/6.jpg)
Add Back PanelAdd the 10" tall back panel to the wine rack. Be sure that you have cut the top of the panel at a 45 degree angle (with the
longest side being the 10" side). Attach the panel using pocket 1 1/4" pocket holes screws and wood glue.
3
Page 6 of 9
![Page 7: DIY Wine Rack Book Ends - learn.kregtool.com](https://reader031.vdocuments.net/reader031/viewer/2022013001/61ca76388d5fb001020ecabd/html5/thumbnails/7.jpg)
Add Bottom PanelAttach the panel using pocket holes, 1 1/4" pocket holes screws and wood glue.4
Page 7 of 9
![Page 8: DIY Wine Rack Book Ends - learn.kregtool.com](https://reader031.vdocuments.net/reader031/viewer/2022013001/61ca76388d5fb001020ecabd/html5/thumbnails/8.jpg)
Fit Bottom PanelMake sure to dry fit the back panel prior to attaching. One edge should be cut at 45 degrees, making the longest edge 9 1/
4" long.
5
Page 8 of 9
![Page 9: DIY Wine Rack Book Ends - learn.kregtool.com](https://reader031.vdocuments.net/reader031/viewer/2022013001/61ca76388d5fb001020ecabd/html5/thumbnails/9.jpg)
Finishing TouchesUse wood putty to fill pocket holes. Once dry, sand, and then stain your rack.6
Page 9 of 9