foundations worldwide inc

Member of the SGS Group

Test Report

No. VNHL2007015002TY

Date: August 25, 2020 of 11

This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx . Attention is drawn to the limitations of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law.

Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.

SGS Vietnam Ltd Lot III/21, 19/5A St, Industrial Group III, Tan Binh IZ, Tan Phu District, HCMC, S.R. Vietnam t (84-28) 3816 0999 f (84-28) 3816 0996

FOUNDATIONS WORLDWIDE INC. 5216 PORTSIDE DRIVE MEDINA, OH 44256 USA The following sample was submitted and identified on behalf of the client as below:

Result Summary

Test Requested Conclusion

I. PHYSICAL TEST --

CPSIA 103 Tracking Labels For Children Products Pass/See result

ASTM F1821-19E1+16 CFR 1217 Standard Consumer Safety Specification For Toddler Beds

Pass/See result

ASTM F1169-19 – Standard Consumer Safety Specification For Full-Size Baby Cribs Pass/See result

16 CFR 1219 – Safety Standard for Full-Size Baby Cribs Pass/See result

II. CHEMICAL TEST --

CPSIA section 101(f) - Lead in paint/similar surface coating material Pass/See result

CPSIA section 101(a)(2) - Lead in accessible substrate materials Pass/See result

CPSIA section 108 – Phthalates 8P Pass/See result

Signed for and on behalf of SGS Vietnam LTD

______________________________ Ung Thanh Van Hardline Lab Manager

SGS Job No. : VNHL2007015002TY

Sample Description : CHILD CRAFT REDMOND ll FULL SIZE CRIB

Characteristic : WOOD

Style / Item No. : F32802

Manufacturer : “DAI TIN”

Country of Origin : VIETNAM

Country of Destination : US

Sample Receiving Date : JULY 30, 2020

Final confirmed Date : JULY 30, 2020

Testing Period : JULY 30, 2020 TO AUGUST 25, 2020

Test Requested : PLEASE REFER TO THE RESULT SUMMARY

Test Results : PLEASE REFER TO NEXT PAGE(S)


Test Report






Test results: Sample Description:

No. Component Material Color

1 CHILD CRAFT REDMOND II FULL SIZE CRIB 1 FINISHED

PRODUCT/WOOD BROWN

2 CHILD CRAFT REDMOND II FULL SIZE CRIB - MAIN BROWN COATING ON WOOD

COATING ON WOOD BROWN

3 CHILD CRAFT REDMOND II FULL SIZE CRIB - METAL SUBSTATE OF FRAME

METAL BLACK SURFACED

4 CHILD CRAFT REDMOND II FULL SIZE CRIB - BLACK COATING ON METAL FRAME

COATING ON METAL BLACK

I. PHYSICAL TEST CPSIA 103 TRACKING LABELS FOR CHILDREN PRODUCTS

Clause Relevant to Sample.

Requirement Rating

1

Scope Children’s Products – for 12 years of age or younger (including Toys) Remark: All FDA regulated products such as cosmetic and food containers are exempted from the tracking label requirements even if it is defined as Children’s Products Default Position – Accept any code as a tracking label

NA

If the tracking label is visible on the product through disposable packaging, there is no need for the label to be on the packaging. If so, “N/A” the whole rating column under “On Packaging” section.

On Packaging

Present on packaging PASS

Permanent PASS

Manufacturer or private labeler PASS

Location of production (City and country) PASS

Date of production (month and year) PASS

Cohort information NA

On Product

Present on product PASS

Permanent PASS

Location of production (City and country) PASS

Date of production (month and year) PASS

Manufacturer or private labeler PASS

Cohort information NA

Note: NA = Not Applicable Remark: This / these test(s) was / were performed by SGS Vietnam’s Hardline lab


Test Report






ASTM F1821-19E1+16 CFR 1217 Standard Consumer Safety Specification For Toddler Beds

Section Parameter/Requirement Results

1

5 General Requirement

5.1 The bed shall conform to the regulations specified in Section 2 of this specification before and after testing.

PASS

5.2 Sharp point or edge PASS

5.3 Small part PASS

5.4 Chemical requirements PASS (See Result #1)

5.5 Prior to testing, any exposed wood parts shall be smooth and free from splinters. PASS

5.6 Scissoring, Shearing, and Pinching PASS

5.7 Protective Components PASS

5.8 Openings PASS

5.9 Labeling PASS

5.10 Corner Post Extensions PASS

6 Performance Requirement PASS

6.1 Mattress Support System PASS

6.2 Mattress Support System Attachment to End Structures PASS

6.3 Mattress Support System Openings PASS

6.4 Guardrails PASS

6.5 End Structures and Side Rails PASS

6.6 Partially Bounded Openings PASS

6.7 Spindle/Slat Static Load Strength PASS

8 Marking and Labeling PASS

9 Instructional Literature PASS

Note: NA = Not Applicable Remark: This/ these test(s) was/ were performed by SGS Vietnam’s Hardline lab.

The above test was accredited ISO 17025:2017 by VILAS

The test results are considered as conform to specification based on the general consideration simple acceptance as stated in ISO/IEC GUIDE 98-4:2012


Test Report






ASTM F1169-19 – Standard Consumer Safety Specification For Full-Size Baby Cribs

Clause Test Method/ Requirement Result

1

5 General Requirements

5.1 Wooden part. PASS

5.2 Surface coating PASS

(See Result #1)

5.3 Small part PASS

5.4 Corner Posts PASS

5.5 Slat construction PASS

5.6 Crib Side Configurations PASS

5.7 Full-Size Baby Cribs – Dimensions PASS

5.8 Spacing of Crib Components PASS

5.9 Toe Holds PASS

5.10 Hardware and Fasteners PASS

5.11 Toy accessories attached to, removed from, or sold with a product, as well as their means of attachment, must meet applicable requirements of Consumer Safety Specification F963.

NA

5.12 Record keeping /

5.13 Except as noted in 6.7, before and after testing, the product shall comply with all the requirements of Section 5.

PASS

5.14 Sharp Points Or Edges PASS

5.15 Flammability. PASS

5.16 Openings PASS

5.17 Scissoring, Shearing, or Pinching PASS

5.18 Labeling PASS

5.19 Cord/Strap Length NA

5.20 Cribs that Fold for Storage or Transport NA

6 Performance Requirements

6.1 Plastic Teething Rail Test Requirement NA

6.2 Cycle Testing PASS

6.3 Crib Side Latch Test Requirements NA

6.4 Mattress Support System Vertical Impact Test Requirements PASS

6.5 Mattress Support System Test Requirement PASS

6.6 Crib Side Test Requirements PASS

6.7 Spindle/Slat Strength Testing PASS

6.8 Cutouts PASS

6.9 Entrapment in Accessories NA


8 Marking and Labeling PASS



Test Report








The test results are considered as conform to specification based on the general consideration simple acceptance as stated in ISO/IEC GUIDE 98-4:2012

16 CFR 1219 – SAFETY STANDARDFOR FULL-SIZE BABY CRIBS

SEC# in F1169

Parameter/ Requirement Result

1

5 General Requirements –

5.1 Wooden part. PASS

5.2 Surface coating PASS

(See Result #1)

5.3 There shall be no small parts as defined by 16 CFR 1501 before testing or liberated as a result of testing to this specification.

PASS

5.4 Corner posts PASS

5.5 Slats shall not contain any lateral/transverse joints such as finger-joints, and other means of joining pieces of lumber end-to-end are not permitted.

PASS

5.6 Crib Side Configurations PASS

5.7 Full-Size Baby Cribs—Dimensions PASS

5.8 Spacing of Crib Components PASS

5.9 Toe Holds PASS

5.10 Hardware and Fastener PASS

5.11 Toy accessories attached to, removed from, or sold with a product, as well as their means of attachment, must meet applicable requirements of Consumer Safety Specification F963.

NA

5.13 Before and after testing, the product shall comply with all the requirements of Section 5.

PASS

5.14 There shall be no hazardous sharp points or edges as defined by 16 CFR 1500.48 and 16 CFR 1500.49 before or after testing to this specification.

PASS

5.15 There shall be no flammable solids as defined in 16CFR 1500.3 (c) (6) (vi) before or after testing in accordance with this specification.

PASS

5.16 Openings PASS

5.17 Scissoring, Shearing, or Pinching PASS

5.18 Labeling PASS

5.19 Cord/Strap Length NA

5.20 Cribs that Fold for Storage or Transport NA

6 Performance Requirements

6.1 Plastic Teething Rail Test Requirement NA

6.2 Cycle Testing PASS

6.3 Crib Side Latch Test Requirements NA

6.4 Mattress Support System Vertical Impact Test Requirements PASS

6.5 Mattress Support System Test Requirement PASS


Test Report






SEC# in F1169

Parameter/ Requirement Result

1

6.6 Crib Side Test Requirements PASS

6.7 Spindle/Slat Strength Testing PASS

6.8 Cutouts PASS

6.9 Entrapment in Accessories NA


8 Labeling PASS




The test results are considered as conform to specification based on the general consideration simple

acceptance as stated in ISO/IEC GUIDE 98-4:2012.


Test Report






II. CHEMICAL TEST Result #1 CPSIA section 101(f) - Lead in paint/similar surface coating material Test Method: CPSC-CH-E1003-09.1 ‘Standard Operating Procedure for Determining Lead (Pb) in Paint and Other Similar Surface Coatings’. Analysis was performed by ICP-MS.

Test item Result (mg/kg) Method detection

Limit (mg/kg) Permissible

Limit (mg/kg) 2 4

Lead (Pb) ND ND 10 90

Comment PASS PASS --- ---

Note : 1. mg/kg = milligram(s) per kilogram= ppm= part(s) per million 2. ND = Not detected

3. With reference to Test Method CPSC-CH-E1003-09.1 dated Feb 25, 2011 the result is calculated using the minimum sample weight.

Remark: The test results are considered as conform to specification based on the general consideration simple acceptance as stated in ISO/IEC GUIDE 98-4:2012. These tests were accredited ISO 17025:2017 by VILAS. These tests were performed by SGS Vietnam’s Chemical lab.

CPSIA section 101(a)(2) - Lead in accessible substrate materials Test Method (metal materials): With reference to CPSC-CH-E1001-08.3. Analysis was performed by ICP-OES.

Test item Result (mg/kg) Method Detection Limit

(mg/kg) Permissible Limit

(mg/kg) 3

Lead (Pb) 11 10 100

Conclusion PASS -- --

Note: 1. % = percentage by weight 2. 1% = 10000ppm (mg/kg) 3. ND = not detected Remark: The test results are considered as conform to specification based on the general consideration

simple acceptance as stated in ISO/IEC GUIDE 98-4:2012. This / these test(s) was / were accredited ISO 17025:2017 by VILAS. This / these test(s) was / were performed by SGS Vietnam’s chemical lab.


Test Report






CPSIA section 108 – Phthalates 8P: Test Method: With reference to CPSC-CH-C1001-09.4. Analysis was performed by GC-MS.

Test item CAS No. Results (%) Method Detection

Limit (%) Permissible

Limit (%) 2 4

Dibutyl Phthalate (DBP) 84-74-2 ND ND 0.005 0.1

Benzylbutyl Phthalate (BBP) 85-68-7 ND ND 0.005 0.1

Bis-(2-ethylhexyl) Phthalate (DEHP)

117-81-7 0.005 ND 0.005 0.1

Di-isononylphthalate (DINP) 28553-12-0 /68515-48-0

ND ND 0.005 0.1

Di-cyclohexylphthalate (DCHP) 84-61-7 ND ND 0.005 0.1

Di-n-Hexylphthalate (DnHP) 84-75-3 ND ND 0.005 0.1

Diisobutyl phthalate (DIBP) 84-69-5 ND ND 0.005 0.1

Di-n-pentylphthalate (DnPP) 131-18-0 ND ND 0.005 0.1

Conclusion -- PASS PASS -- --

Note: 1. % = percentage by weight

2. 1% = 10000ppm (mg/kg) 3. ND = Not Detected

Remark: The test results are considered as conform to specification based on the general consideration

simple acceptance as stated in ISO/IEC GUIDE 98-4:2012. This / these test(s) was / were accredited ISO 17025:2017 by VILAS. This / these test(s) was / were performed by SGS Vietnam’s chemical lab.


Test Report






PHOTO OF SUBMITTED SAMPLE FOR TESTING


Test Report







Test Report






CARTON LAYOUT REGISTRATION CARD (1)

REGISTRATION CARD (2)

REPORT RESULTS REFER TO SUBMITTED SAMPLE (S) ONLY

*** End of Report ***