installation instructions k-6098in-s vitreous china...
TRANSCRIPT
Silicon SealantMeasuring Tape
RECOMMENDED TOOLS AND MATERIALS
Teflon Tape
File
Hacksaw Spirit Level 10” Adjustable Wrench
K-6088IN P-Trap
BEFORE YOU BEGIN
RECOMMENDED TANKS
WARNING: Risk of personal injury or product damage. Handle with care.Vitreous China can break or chip if the bolts and nuts are over-tightened, or if the product is handled carelessly.
Observe all local plumbing and building codes. Carefully inspect the new toilet for any damage. If the Inwall tank is not installed, refer to the manufacturer’s instructions before installation.
ORDERING INFORMATIONReplay Wall-hung Toilet....................................K-6098IN-S*
Includes Toilet Bowl.....................................K-6088IN*Includes Quiet-close Toilet Seat...................K-6091IN*
1206314-IN01-A -1-
ROUGHING-IN
Description Inwall Tank Cover/ Face Plate
Ÿ All dimensions in inches (cm). Fixture dimensions are nominal and conform to tolerances as per ASME Standard A112. 19.2M.Ÿ Product illustrations shown are representative only; actual products may vary.Ÿ Kohler reserves the right to make changes in product characteristics, packaging or availability at any time without notice.
CAUTION : Do not use white cement or high lime-content cements to install this toilet. The expansion of cement due to rise in temperature may cause the toilet to use of cement.crack or be damaged. Kohler is not responsible for any damage due to installation with the
REPLAYINSTALLATION INSTRUCTIONS
K-6098IN-SVITREOUS CHINA WALL-HUNG P-TRAP TOILET
* Available in “-0 (White)” & “-96 (Biscuit)”
K-4177IN-2-CP/ K-8857IN-2-CPK-4178IN-2-NAHydro Tower 310 In-wall tank 3/6 L
7-1/8" (18.1 cm)*
13-1
3/1
6"
(35 c
m)
12-3
/8"
(31.5
cm
)*
8-1
/2"
(21.5
cm
)
16-15/16"
9-3
/4"
(25.2
cm
)
8"
(20 c
m)
14-1/4" (36 cm)
21-1/4" (54 cm)
11-1
5/1
6"
(30.3
cm
)
14-7
/16"
(37.1
cm
)
(43 cm)
Ø4"
Ø2-3
/16"
15-3
/4"
(40 c
m)
(10.2
cm
) (
5.5
cm
)
Unit: Inches (cm)* Bowl mounting dimensions
NOTE:- Use appropriate Steel Frame / Chair Bracket / Rack Bolts (M12 min.) for load bearing, as required.
Hydro Tower 310 In-wall tank 3/4.5 L K-4179IN-2-NAHydro Tower 310 In-wall tank 3/6 L Side InletHydro Tower 310 In-wall tank 3/4.5 L Side Inlet
K-4178IN-2S-NAK-4179IN-2S-NA
K-8857IN-2-B07K-8857IN-2-MS1K-8857IN-2-B04
TM
Cut bolts if needed. File bolt ends.
35mm
in
Inds
Mount the sleeve on the bolts and remove inlet plug.
5Inds
6Slide the inlet pipe into the wall openingsfor water inlet. Test fit the toilet.
7 Remove the toilet. Cut and file the inlet pipeto the proper length by removing excess
8
Inds
13
Mount the toilet on the wall.
14accessories using allen key. Close the installation holes using the caps.
Flush the toilet. Check for leaks. Seal connections if required.
15 Seal around the edges. Do not use cement.
9
Slide the outlet pipe into the wall openings for waste pipe. Test fit the toilet.
Inds
10 11Remove the toilet. Cut and file the outlet length by removing pipe to the proper
12Add silicon sealant in the gasket grooves.
Recommended Installation Parts
1206314-IN01-A -2-
INSTALLATION GUIDELINE
Note: Dimension A and B ( as shown in picture 6 to 10 above) to be adjusted as per specific site requirements.
in
Toll Free 1800 103 2244 Outlet Connection*
Inlet Connection*
Wall Installation Kit**
E5534-CP
*Installation parts shown above are not supplied with the product and are procured separately. **Wall Installation kit shown above is supplied with toilet.
1112180 / 1045092
Level the toilet and tighten
Note the distance between the wall and the toilet at the location shown.Measure excess length “A” for the inlet pipe.
Note the distance between the wall and the toilet at the location shown. Measure
excess length “B” for the outlet pipe.
Install the accessory kit into the
installation hole of the toilet.
10
Slide the gaskets on the inlet & outlet pipeas shown.
3
1046327 (includes 1169520)
length “A”.
excess length “B”.
1169520 1046327-S