installation manual - viladonis.gr · installation manual proximity card reader kdh-c330u/h/m-black...
TRANSCRIPT
Installation Manual
PROXIMITY CARD READER
KDH-C330U/H/M-BLACK KDH-C330U/H/M-IVORY KDH-CK330U/H/M-BLACK KDH-CK330U/H/M-IVORY
WERSJA 1.0
Proximity card reader – Installation manual
All rights reserved. © AAT HOLDING S.A. 2
1. Introduction
KDH-C330U/H/M-BLACK_IVORY KDH-CK330U/H/M-BLACK_IVORY Proximity card reader type KDH-C330_CK330U/H/M is designed for use in access control systems. It can be installed inside or outdoors. It has a housing made of ABS plastic meets the requirements of IP66 (waterproof) and tamper protection. Reader is designed to work with controllers with Wiegand interface. The device reads the card Unique (125 kHz), HID Prox (125 KHz) and Mifare Classic (13.56 MHz). Switch-able Wiegand format and two-color housing mean that this product is universal for vari-ous installations. The range of the proximity card reading is from 2 to 10 cm depending on the type of card. Characteristics reader - For cooperation with controllers with Wiegand port - Proximity card types - Unique and HID Prox 26 bits (125 kHz) Mifare Classic (13.56 MHz) - Available model with keypad for PIN+card option (CK330) - Waterproof, meets the requirements of IP66 - Built-in tamper switch the type of LDR - activates the buzzer - Built-in sounder and optical-red / green LED - Power supply 12 VDC
Technical specifications
Name of parameters or function Parameters value or description
- Supply power 12 VDC +/- 10%
- Current load : C330U/H/M / CK330U/H/M < 25 mA / < 35 mA
- Proximity card read range Od 2 do 10 cm (depend of card type)
- Card type UNIQUE, HID Prox (125 kHz), Mifare (13,56 MHz)
- switched Wiegand card format - switched Wiegand keypad format (only for model CK330)
26/34 (Unique, Mifare), 26 i 37 (HID Prox) auto. 4/8 bits
- Wiegand port D0, D1
- Environments For indoor and outdoor, IP66
- Operating temperature range Od –40°C do +60°C
- Operating humidity range 10% - 95% RH
- Dimensions C330U/H/M CK330U/H/M
120 x 48 x 20 mm 125 x 50 x 21 mm
Proximity card reader – Installation manual
All rights reserved. © AAT HOLDING S.A. 3
READER INSTALLATION
Separate the back cover with holes and use as a template Drill 2 holes (A, C) in the wall of the bolt and one under the cable Insert the bolt holes (A, C) attached dowels Screw the rear part of the housing to the wall using the screws Bring out the controller cables through the hole (B) Mount the controller on the base and secure it from below with a special
screw
Wiring Diagram
Red +12V DC
Black GND
Green D0
White D1
Brown LED
Yellow Buzzer
Change card Wiegand output format procedure: - 26 bit Wiegand (Unique, Mifare) - * 1 2 3 4 5 6 # 7 2 26 # * * - exit - 34 bit Wiegand (Unique, Mifare) - * 1 2 3 4 5 6 # 7 2 34 # * * - exit - 26 & 37 bitów (HID Prox) - automatic, depend of card number Change PIN output format procedure: - Virtual card number format - * (1 2 3 4 5 6) # 7 3 0 # * * - exit - 4 bit format (KaDe) - * (1 2 3 4 5 6) # 7 3 1 # * * - exit - 8 bit format (Kantech) - * (1 2 3 4 5 6) # 7 3 2 # * * - exit