introduction - applied btu | hvac technical ... vimco is pleased and excited to release our newest...
TRANSCRIPT
INTRODUCTION
VIMCO is pleased and excited to release our newest marketing literature: the G-1010 booklet. This booklet providescondensed information on our entire range of vibration and noise isolation products. The information includesproduct features, application information, dimensional data and model selection tables. We expect this booklet to bean invaluable resource for engineers, representatives, distributors and contractors.
One new tool that we are introducing in this latest literature is our exclusive isolator 5 star rating system . Vibrationisolation efficiency is directly related to the amount of deflection (compression) of the isolating element. The isolationefficiency chart below illustrates the theoretical relationship between isolation efficiency, disturbing frequency andisolator static deflection
Disturbing frequency is the frequency of vibration produced by an unbalanced,rotating or reciprocating movement in mass.Natural frequency is the number of complete cycles of oscillation a mass will vibratein a given unit of time if a force displaces it from its equilibrium position and allows itto vibrate freely.Static deflection is the distance an isolator will deflect under the static or dead weightof the equipment.Isolation efficiency is the percentage reduction in the amplitude of the transmittedmechanical vibration.
We have classified our range of vibration isolators in 5 category's based on their isolation efficiency as detailed below.Each isolator selection table within this catalog indicates the isolator star rating.
* Isolator efficiencies are nominal based on equipment disturbing frequency of 1800rpm
www.vimco.biz G-1010 Rev. 2 (page 2)
Star rating Isolator Deflection Isolator efficiency Performance classification
more than 2.50"from 1.51" to 2.50"from 0.51" to 1.50"from 0.21" to 0.50"
up to 0.20" 92%96%98%99%
99.5%
BasicModerate
GoodVery GoodExcellent
Housed Spring Mounts
Features + Application Information1. Powder coated cast iron housings (70-110 micron ASTMD4138-07a) 5. Adjust mounting so that upper housing clears lower housing by2. Internal elastomeric snubbers prevent metal to metal contact at least 1/4" but not more than 1/2"3. Anti-skid elastomeric acoustical pad 6. Spring elements color-coded for easy field verification4. Built-in leveling device 7. Consult spring chart on page 22 for isolator performance data
Dimensional + Model Selection Data (Refer to page 2 for isolator star rating system)
ZA / ZB / ZC / ZD models 1" deflection series
(*) Free height 'H' indicated in table
is for ZA isolator. For free height of
ZB/ZC models, add 1/4". For free
height of ZD model add 1/2".
AA-1 / AB-1 / AC-1 / AD-1 models
(*) Free height 'H' indicated in table
is for AA-1 isolator. For free height
of AB-1/AC-1 models, add 3/8". For
free height of AD-1 model add 5/8".
AA-2 / AB-2 / AC-2 / AD-2 models
2" deflection series
(*) Free height 'H' indicated in table
is for AA-2 isolator. For free height
of AB-2/AC-2 models, add 1/2". For
free height of AD-2 model add 3/4".
AA-4 / AB-4 / AC-4 / AD-4 models
(*) Free height 'H' indicated in table
is for AA-4 isolator. For free height
of AB-4/AC-4 models, add 1/2". For While ordering specify mounting style model in place of "x" free height of AD-4 model add 3/4". e.g. for pin top internal adjustment order A B -1-110
www.vimco.biz G-1010 Rev. 2 (page 5)
Model AA-2:External adjustment
Model AB-2:Internal adjustment, pin top
Model ZA:External adjustment
Model ZB:Internal adjustment, pin top
Model AA-1:External adjustment
Model AB-1:Internal adjustment, pin top
Model AC-4:Internal adjustment, flat top
Model AD-4:Internal adjustment, neoprene top
Model ZC:Internal adjustment, flat top
Model ZD:Internal adjustment, neoprene top
Model AC-2:Internal adjustment, flat top
Model AD-2:Internal adjustment, neoprene top
Model AA-4:External adjustment
Model AB-4:Internal adjustment, pin top
Model AC-1:Internal adjustment, flat top
Model AD-1:Internal adjustment, neoprene top
6-1/2"
6-3/4"
7"
Due to our policy of continual product development and improvement, all specifications
311 to 410Ax-1-144 411 to 595
Ax-1-141-146B 596 to 647Ax-1-147
are subject to change without prior notice. Please consult your local rep. for updates.
Model Load RangeAx-1-140 1 to 80Ax-1-141 81 to 160Ax-1-142 161 to 310Ax-1-143
648 to 1190Ax-1-148A 1191 to 1576
Ax-1-147-146B 1577 to 1690
2381 to 3152Ax-2-147-146B 3153 to 3380
Ax-1-148A-146B 1691 to 2076
Ax-2-147 2077 to 2380
5-3/4"
6"
Zx-121
Ax-2-148A-146B 3381 to 4152
H (*)
4"
5-1/2"
2161 to 25002501 to 2660
Ax-4-147-146B 6306 to 6760
5331 to 55305531 to 62006201 to 7330
Ax-4-147 4153 to 4760Ax-4-148A 4761 to 6305
Ax-2-148A
Ax-4-148A-146B 6761 to 8305
3101 to 3665
3666 to 43304331 to 50005001 to 5330
Ax-4-110-113Ax-4-111-113Ax-4-112-113
Ax-2-112-113
1251 to 1330
2661 to 27602761 to 3100
1331 to 13801381 to 15501551 to 1832
1833 to 2160
131 to 210
751 to 910911 to 1080
1081 to 1250
211 to 300301 to 370371 to 700
701 to 750
Ax-4-109-113
Ax-2-112Ax-2-109-113Ax-2-110-113Ax-2-111-113
Ax-1-112-113
Ax-2-111
Ax-4-111Ax-4-112
Ax-1-112Ax-1-109-113Ax-1-110-113Ax-1-111-113
Zx-127
Ax-1-109Ax-1-110Ax-1-111
Zx-124
Model
Zx-125Zx-126
Load Range (lbs) H (*)
Zx-122Zx-123
1 to 5051 to 80
81 to 130
Free Standing Spring Mounts
Features + Application Information1. Large diameter laterally stable springs 5. Consult spring chart on page 22 for isolator performance data2. Anti-skid elastomeric acoustical cup / pad3. Built-in leveling device4. Spring elements color-coded for easy field verification
Dimensional + Model Selection Data (Refer to page 2 for isolator star rating system)
BA / BB / BD / BE / BG / BH / BN / BO / BP models WELD FREE CONSTRUCTION*WELD FREE CONSTRUCTION 1" deflection series
A B C D E F J Kn/a n/a n/a n/a 2 3/8" 3/8" 5/8" n/a
n/a n/a n/a n/a 2 7/8" 3/8" 5/8" n/a
6" 4" 5" 5/8" 2 3/8" 3/8" 5/8" 1/8" 3" deflection series6" 4" 5" 5/8" 2 7/8" 3/8" 5/8" 1/8"n/a n/a n/a n/a 2 3/8" n/a n/a n/a
n/a n/a n/a n/a 2 7/8" n/a n/a n/a
n/a n/a n/a n/a 1 1/2" 1/4" 3/8" n/a
4" 2" 3" 3/8" 1 1/2" 1/4" 3/8" n/a
n/a n/a n/a n/a 1 1/2" n/a n/a 1/8"
OSM-1A models*WELDED CONSTRUCTION
(CUP TYPE) WELDED CONSTRUCTION*Mounting holes furnished standard 1" deflection series*Galvanized finish
OSM-1B models*WELDED CONSTRUCTION
(CUP TYPE)
*Mounting holes furnished standard
*Galvanized finish 3" deflection series
www.vimco.biz G-1010 Rev. 2 (page 6)
7-3/4"
OSM-1B-186-199 1158 to 1470OSM-1B-187-199 1471 to 1825
333 to 580OSM-1B-186 581 to 850
211 to 332
OSM-1B-181
OSM-1B-157 751 to 910
131 to 210
HModel Load Range
4-1/2"(BA/BD models)
3-3/4"(BG models)
5-1/2"(BB/BE models)
4-3/4"(BH models)
H
BB-186-199 / BE-186-199 / BH-186-199 1158 to 1470
7-7/8"(BB/BE models)
7-1/8"(BH models)
BA-124 / BD-124 / BG-124 186 to 210BA-125 / BD-125 / BG-125 211 to 300
H
3-3/4"
5-5/8"
BNBOBP
301 to 370
OSM-1B-159-161 2083 to 2603
911 to 1500
BEBGBH
Model BP/BG/BH:w/o height adjustmentor anchoring option
Mount Series
BABBBD
Model BN/BA/BB:w/o base plate
are subject to change without prior notice. Please consult your local rep. for updates.
Due to our policy of continual product development and improvement, all specifications
OSM-1A-127
OSM-1B-158
Model
BA-126 / BD-126 / BG-126
Dimensions
OSM-1A-126
BB-187-199 / BE-187-199 / BH-187-199
Model BO/BD/BE:with base plate
1471 to 1825
OSM-1B-159 1501 to 2082
371 to 700OSM-1B-156 701 to 750
OSM-1A-125 211 to 300
OSM-1A-122
OSM-1B-187 851 to 1157
1 to 100OSM-1B-182 101 to 150OSM-1B-183 151 to 210OSM-1B-184OSM-1B-185
51 to 80OSM-1A-123 81 to 130OSM-1A-124
Load Range (lbs)OSM-1A-121 1 to 50
Model Load Range (lbs)
BN-043 / BO-043 / BP-043 36 to 65BN-044 / BO-044 / BP-044 66 to 90BN-045 / BO-045 / BP-045
HBN-041 / BO-041 / BP-041 1 to 15BN-042 / BO-042 / BP-042 16 to 35
3-1/4"(BN/BO models)
2-3/4"(BP models)91 to 185
301 to 370BA-127 / BD-127 / BG-127 371 to 700BB-156 / BE-156 / BH-156 701 to 750BB-157 / BE-157 / BH-157 751 to 910BB-158 / BE-158 / BH-158 911 to 1500
BB-159-161 / BE-159-161 / BH-159-161 2083 to 2603BB-159 / BE-159 / BH-159 1501 to 2082
Model Load RangeBB-181 / BE-181 / BH-181 1 to 100BB-182 / BE-182 / BH-182 101 to 150BB-183 / BE-183 / BH-183 151 to 210BB-184 / BE-184 / BH-184 211 to 332BB-185 / BE-185 / BH-185 333 to 580BB-186 / BE-186 / BH-186 581 to 850BB-187 / BE-187 / BH-187 851 to 1157
Free Standing Spring Mounts
Features + Application Information1. Large diameter laterally stable springs 5. Built-in leveling device2. Welded steel construction & galvanized finish 6. Spring elements color-coded for easy field verification3. Anti-skid elastomeric acoustical pad 7. Consult spring chart on page 22 for isolator performance data4. Mounting holes furnished as standard
Dimensional + Model Selection DataOSM-1 models
OSM-2 models
OSM-4 models
www.vimco.biz G-1010 Rev. 2 (page 7)are subject to change without prior notice. Please consult your local rep. for updates.
Due to our policy of continual product development and improvement, all specifications
Model Load Range (lbs)
271 to 370OSM-1-154 371 to 500OSM-1-155 501 to 600OSM-1-156
H
1"
de
fle
cti
on
se
rie
s
OSM-1-150 1 to 100
4-7/8"
OSM-1-151 101 to 180OSM-1-152 181 to 270OSM-1-153
601 to 750OSM-1-157 751 to 910OSM-1-158 911 to 1500OSM-1-159 1501 to 2082
OSM-1-159-161 2083 to 2603
OSM-2-158 2604 to 30004-7/8"OSM-2-159 3001 to 4165
OSM-2-159-161 4166 to 5207
OSM-4-158 5208 to 60005-1/8"OSM-4-159 6001 to 8330
OSM-4-159-161 8331 to 10415Model Load Range (lbs) H
2"
de
fle
cti
on
se
rie
s
OSM-1-140 1 to 80
6-1/4"
OSM-1-141 81 to 160OSM-1-142 161 to 310OSM-1-143 311 to 410OSM-1-144 411 to 595
OSM-1-141-146B 596 to 647OSM-1-147 648 to 1190
OSM-1-148A 1191 to 1576OSM-1-147-146B 1577 to 1690
OSM-1-148A-146B 1691 to 2076
OSM-2-147 2077 to 2380
6-1/4"OSM-2-148A 2381 to 3152
OSM-2-147-146B 3153 to 3380OSM-2-148A-146B 3381 to 4152
OSM-4-147 4153 to 4760
6-1/2"OSM-4-148A 4761 to 6305
OSM-4-147-146B 6306 to 6760OSM-4-148A-146B 6761 to 8305
Model Load Range (lbs) H
3"
de
fle
cti
on
se
rie
s
.
OSM-1-181 1 to 100
7-1/4"
OSM-1-182 101 to 150OSM-1-183 151 to 210OSM-1-184 211 to 332OSM-1-185 333 to 580OSM-1-186 581 to 850OSM-1-187 851 to 1157
OSM-1-186-199 1158 to 1470OSM-1-187-199 1471 to 1825
OSM-2-187 1826 to 23167-1/4"OSM-2-186-199 2317 to 2950
OSM-2-187-199 2951 to 3650
OSM-4-187 3651 to 46327-1/2"OSM-4-186-199 4633 to 5910
OSM-4-187-199 5911 to 7300
Vertically Restrained Spring Mounts
Features + Application Information1. Applications requiring vertical restraint due to reduced equipment 4. Elastomeric 'non-short circuiting' grommets loads or large external forces e.g. wind 5. Built-in leveling device2. Welded steel construction & galvanized finish 6. Spring elements color-coded for easy field verification3. Mounting holes furnished as standard 7. Consult spring chart on page 22 for isolator performance data
Dimensional + Model Selection DataRSM-1 models
RSM-2 models
RSM-4 models
* RESTRICTO TM assembly limits vertical movement due to reduced
loads or external forces (wind loads)
* Adjust RESTRICTO TM assembly vertical limiting nuts as per clearance
levels specified by project engineer (standard: 1/4", maximum: 1/2")
www.vimco.biz G-1010 Rev. 2 (page 8)are subject to change without prior notice. Please consult your local rep. for updates.
Due to our policy of continual product development and improvement, all specifications
RSM-4-187 3651 to 46328-7/8"RSM-4-186-199 4633 to 5910
RSM-4-187-199 5911 to 7300
RSM-2-187 1826 to 23168-3/8"RSM-2-186-199 2317 to 2950
RSM-2-187-199 2951 to 3650
RSM-1-186-199 1158 to 1470RSM-1-187-199 1471 to 1825
RSM-1-186 581 to 850RSM-1-187 851 to 1157
151 to 210RSM-1-184 211 to 332RSM-1-185 333 to 580
Model Load Range (lbs) H
3"
de
fle
cti
on
se
rie
s
.
RSM-1-181 1 to 100
8-1/4"
RSM-1-182 101 to 150RSM-1-183
RSM-4-147 4153 to 4760
7-7/8"RSM-4-148A 4761 to 6305
RSM-4-147-146B 6306 to 6760RSM-4-148A-146B 6761 to 8305
7-3/8"RSM-2-148A 2381 to 3152
RSM-2-147-146B 3153 to 3380RSM-2-148A-146B 3381 to 4152
RSM-1-148A-146B 1691 to 2076
RSM-2-147 2077 to 2380
RSM-1-148A 1191 to 1576RSM-1-147-146B 1577 to 1690
RSM-1-141-146B 596 to 647RSM-1-147 648 to 1190
161 to 310RSM-1-143 311 to 410RSM-1-144 411 to 595
Model Load Range (lbs) H
2"
de
fle
cti
on
se
rie
s
RSM-1-140 1 to 80
7-1/4"
RSM-1-141 81 to 160RSM-1-142
RSM-4-158 5208 to 60006-1/2"RSM-4-159 6001 to 8330
RSM-4-159-161 8331 to 10415
RSM-2-158 2604 to 30006"RSM-2-159 3001 to 4165
RSM-2-159-161 4166 to 5207
RSM-1-159 1501 to 2082RSM-1-159-161 2083 to 2603
RSM-1-157 751 to 910RSM-1-158 911 to 1500
RSM-1-155 501 to 600RSM-1-156 601 to 750
181 to 270RSM-1-153 271 to 370RSM-1-154 371 to 500
Model Load Range (lbs) H
1"
de
fle
cti
on
se
rie
s
RSM-1-150 1 to 100
5-7/8"
RSM-1-151 101 to 180RSM-1-152
Seismic Restrained Spring Mounts (All-Directional)
Features + Application Information1. Large diameter laterally stable springs 5. All isolators certified to withstand minimum 1.39 G force2. Welded steel construction 6. Suitable for most seismic zone IV applications3. Built-in leveling device 7. Spring elements color-coded for easy field verification4. Mounting holes furnished as standard 8. Consult spring chart on page 22 for isolator performance data
Dimensional + Model Selection Data (Refer to page 2 for isolator star rating system)
SSMA-1 models 1" deflection series
2" deflection series
*Powder coated housing (50-70 micron ASTMD4138-07a)
*Housing will be elevated from ground when installed.
Pull down to floor with anchor bolts.
B C6" 3" 3" deflection series7" 4"
SSM-1 models
Select SSM-1 models instead of SSMB-1 where higher 'G' ratings are required.
'G' ratings for SSMA-1 based on shake table testing at ISO 17025 accredited
laboratory in accordance with ASCE 7-05 design parameters under OSHPD
Special Seismic Certification Preapproval (OSP) program.
'G' ratings for SSM-1, SSMB-1 based on attachment to steel. For concrete
ratings will be controlled by attachment methods + concrete strength.
*Zinc metallized housing
www.vimco.biz G-1010 Rev. 2 (page 9)
2.14 / 2.991.74 / 2.43
5.59 / 7.81
1.39 / 1.94
'G' Rating
3.03 / 4.242.29 / 3.2
648 to 11901191 to 1576
21.77 / 30.4211.58 / 16.188.69 / 12.15
6.08 / 8.5
81 to 160
are subject to change without prior notice. Please consult your local rep. for updates.
Due to our policy of continual product development and improvement, all specifications
32.5019.6911.817.515.284.332.32
3.95 / 5.524.82 / 6.74
1577 to 1690
311 to 410411 to 595
2.41 / 3.371.73 / 2.42
1691 to 2076
43.87 / 61.31
SSMB-1-143 / SSM-1-143SSMB-1-144 / SSM-1-144
SMB-1-148A-146B / SSM-1-148A-146
Load Range (lbs)1 to 80
1501 to 2082
SSMB-1-147-146B / SSM-1-147-146B
SSMB-1-140 / SSM-1-140SSMB-1-141 / SSM-1-141
SSMB-1-147 / SSM-1-147
SSMB-1-159-161 / SSM-1-159-161
SSMB-1-148A / SSM-1-148A
371 to 700
701 to 750
2083 to 2603
SSMB-1-141-146BSM-1-141-146B 596 to 647
161 to 310
Model
SSMA-1-127
SSMB-1-156 / SSM-1-156SSMB-1-157 / SSM-1-157
Model
SSMA-1-125SSMA-1-126
SSMA-1-121SSMA-1-122SSMA-1-123
SSMB-1-158 / SSM-1-158
SSMA-1-124
SSMB-1-142 / SSM-1-142
SSMB-1-159 / SSM-1-159
'G' Rating
131 to 210
751 to 910911 to 1500
211 to 300
1 to 5051 to 80
81 to 130
Load Range (lbs)
301 to 370
'G' RatingSSM-1-181 1 to 100 47.05
Model Load Range
30.42SSM-1-183 151 to 210 22.48SSM-1-182 101 to 150
15.21SSM-1-185 333 to 580 8.32SSM-1-184 211 to 332
581 to 850 5.67SSM-1-187 851 to 1157 4.37SSM-1-186
1158 to 1470 3.28SSM-1-187-199 1471 to 1825 2.77SSM-1-186-199
Mount Series
DimensionsA D E
1-1/2"SSMB-1 7-3/8" 5-1/2" 2-1/2"SSMA-1 4-5/8" 4-1/2"
Vibration Isolation Pads
Features + Application Information1. Simple field installation2. Wherever bolting is to be avoided and minor, non-critical vibration conditions exist (pumps, motors, a/c units, generators etc.)
Dimensional + Model Selection Data (Refer to page 2 for isolator star rating system)
3RFP series Defl.* Higher deflection than conventional pads
* Excellent resistance to oil, water, ozone
(suitable / recommended for outdoor use)
* Closed cell construction with excellent sound
attenuation capability
* Free from sulfur, halogens, formaldehydes,
phthalates and other toxins
* Lifetime warranty against core separation
Maximum loading: 70 psi
Material: closed cell, chemically cross-linked HD rubber foam (with LD core)
RMP series* Alternate high-low rib construction
* High quality ozone + water resistant elastomer
Maximum loading: 60 psi
Material: 55 duro elastomer blend
CRMP series* Alternate high-low rib construction
* Environment friendly 100% natural cork core
* Excellent sound attenuation capability
* High quality ozone + water resistant elastomer
Maximum loading: 60 psi
Material: Low density cork, elastomer blend
ECRMP series* New 1" modules offer greater versatility at
jobsite to cut to exact size requirements.
* Easy cut construction (by hand or utility knife)
* Waffle pad design with inbuilt suction cups
* High quality ozone + water resistant elastomer
Maximum loading: 60 psi
Material: 55 duro elastomer blend
SRMP series
* High quality ozone + water resistant elastomer
Maximum loading: 60 psi Contact factory for non-standard sizesMaterial: 55 duro elastomer blend, Galvanized steel plate
www.vimco.biz G-1010 Rev. 2 (page 10)
Alternate high-low rib construction Waffle pad design with inbuilt suction cups
are subject to change without prior notice. Please consult your local rep. for updates.
Due to our policy of continual product development and improvement, all specifications
SRMP-2R SRMP-3R SRMP-2E SRMP-3E
SR
MP
ser
ies
SRMP-2R 0606
Model Size Max load (lbs)
3RF
P s
erie
s
3RFP 181801 18" x 18" x 1" 22680
3RFP 030301 3" x 3" x 1" 630
.25"
3RFP 121201 12" x 12" x 1" 100803RFP 060601 6" x 6" x 1" 25203RFP 040401 4" x 4" x 1" 1120
3RFP 020201 2" x 2" x 1" 2803RFP 181802 18" x 18" x 2" 22680
.50"
3RFP 121202 12" x 12" x 2" 100803RFP 080802 8" x 8" x 2" 44803RFP 060602 6" x 6" x 2" 25203RFP 040402 4" x 4" x 2" 11203RFP 030302 3" x 3" x 2" 6303RFP 020202 2" x 2" x 2" 280
RM
P s
erie
s .
RMP 181838 18" x 18" x 3/8" 19440
RMP 030338 3" x 3" x 3/8" 540
.11"
RMP 121238 12" x 12" x 3/8" 8640RMP 060638 6" x 6" x 3/8" 2160RMP 040438 4" x 4" x 3/8" 960
RMP 020238 2" x 2" x 3/8" 240
CR
MP
ser
ies
CRMP 181801 18" x 18" x 1" 19440
CRMP 030301 3" x 3" x 1" 540
.18"
CRMP 121201 12" x 12" x 1" 8640CRMP 060601 6" x 6" x 1" 2160CRMP 040401 4" x 4" x 1" 960
CRMP 020201 2" x 2" x 1" 240CRMP 181802 18" x 18" x 2" 19440
.20"
CRMP 121202 12" x 12" x 2" 8640CRMP 060602 6" x 6" x 2" 2160CRMP 040402 4" x 4" x 2" 960CRMP 030302 3" x 3" x 2" 540CRMP 020202 2" x 2" x 2" 240
EC
RM
P s
erie
s
ECRMP 181834 18" x 18" x 3/4" 19440
ECRMP 020234 2" x 2" x 3/4" 240ECRMP 010134 1" x 1" x 3/4" 60
.18"
ECRMP 060634 6" x 6" x 3/4" 2160ECRMP 040434 4" x 4" x 3/4" 960ECRMP 030334 3" x 3" x 3/4" 540
.22"SRMP-2R 0404 4" x 4" x 13/16" 960SRMP-2R 0303 3" x 3" x 13/16" 540
6" x 6" x 13/16" 2160
.33"SRMP-3R 0404 4" x 4" x 1 1/4" 960SRMP-3R 0303 3" x 3" x 1 1/4" 540
SRMP-3R 0606 6" x 6" x 1 1/4" 2160
.36"SRMP-2E 0404 4" x 4" x 1 9/16" 960SRMP-2E 0303 3" x 3" x 1 9/16" 540
SRMP-2E 0606 6" x 6" x 1 9/16" 2160
SRMP-3E 0606 6" x 6" x 2 3/8" 2160.54"SRMP-3E 0404 4" x 4" x 2 3/8" 960
SRMP-3E 0303 3" x 3" x 2 3/8" 540
Double Deflection, Rubber-in-shear Mounts
Features + Application Information1. Anti-skid top and bottom surfaces 5. High deflection, low natural frequency2. Mounting holes furnished as standard 6. Elements color-coded for easy field verification3. Embedded steel plates for uniform loading (Color coding can be by 'dot' or 'complete element')4. Ozone + water resistant elastomer 7. Optional lock-down bolt and washer available
Dimensional + Model Selection DataFMD models (Refer to page 2 for isolator star rating system)
0.5" deflection series
A B C D E F G H
*Models FMD-E and FMD-F have
rectangular bases.
Light Duty Hangers
Features + Application Information1. Elements incorporate projected collar to prevent 4. AVHM provides up to 17dB(A) noise reduction metal to metal contact between rod and bracket 5. AVHM series designed for use with all thread rod2. Includes steel cups / plates for uniform loading 6. HNW series designed for use with wire, strap e.g. false ceiling, suspended3. Ozone + water resistant elastomer attic equipmentDimensional + Model Selection DataAVHM models HNW models
(Refer to page 2 for isolator star rating system) (Refer to page 2 for isolator star rating system)
AVHM series HNW series
A B C 1/5 0.43 0.73 1.28 1/5 1/5 0.43 1.02 1.67 1/5
1/5
www.vimco.biz G-1010 Rev. 2 (page 11)
Typical installation Typical installation
ModelLoad range
(lbs)Defl.(inch)
Color
HNW-1 1 to 65 REDHNW-2 66 to 120 BLACKHNW-3 121 to 200 BLUE
ModelLoad Range
(lbs)Defl.(inch)
Dimensions (in.)
AVHM-50 1 to 110AVHM-100 111 to 220
Model
FMD-A-1FMD-A-2FMD-A-3FMD-A-4
FMD-B-1FMD-B-2FMD-B-3
FMD-F-2FMD-F-3FMD-F-4
FMD-B-4
FMD-E-3FMD-E-4
FMD-F-1 501 to 750751 to 1000
1001 to 1500
236 to 375
376 to 400
116 to 130131 to 165166 to 235
401 to 500
1 to 3031 to 4041 to 70
71 to 115
1501 to 2200
Isolator Dimensions (inches)
1 3/4 2 3/8 3 1/8 5/16 11/32 1 1/4 1 3/8 3/16
2 3/8 3 3 7/8 3/8 11/32 1 3/4 1 3/4 7/32
1 3/4 1/42 3/8 3 1/8 4 3/8
ColorLoad Range (lbs)
BLUE
9/16 3 1/2 2 3/4 3/83 5/8 4 3/4 5 7/8
REDGREENBLACK
BLUERED
GREENBLACK
GREEN
BLACK
Due to our policy of continual product development and improvement, all specifications
are subject to change without prior notice. Please consult your local rep. for updates.
BLACK
BLUERED
GREEN1/2
1/2 2
Double Deflection, Rubber-in-shear Hangers
Features + Application Information1. Powder coated steel bracket (50-70 micron ASTM D4138-07a) 4. Ozone + water resistant elastomer2. Element incorporates projected collar to prevent 5. High deflection, low natural frequency metal to metal contact between rod and bracket 6. Elements color-coded for easy field verification3. Embedded steel plate(s) for uniform loading (Color coding can be by 'dot/stripe' or 'complete element')
Dimensional + Model Selection Data (Refer to page 2 for isolator star rating system)
APH / HND models 0.5" deflection series APH-A, HND-A, APH-B series have nominal 0.4" deflection
A B C D E
APHE / HNDE models 0.5" deflection series APHE-A, HNDE-A, APHE-B series have nominal 0.4" deflection
ColorA B C E H NH N NC
* Bottom washer only provided on HNDE
series elements
www.vimco.biz G-1010 Rev. 2 (page 12)
3 1/8 1/4 1 1/8 1.313 4 7/8 3/4
3 1/8 1 1/8 1 3/8 1.312 1/2 3 1/2 7/8 1/2
0.11 1.00 1.16
1 7/8 2 1/4 7/8 5/8 1.69 1/4 1 1/8
3/4
6 3 1/4 3 1/2 4
5/8
2.82 1.57 1.77 1.77
REDHND-A-3 41 to 70 GREEN
2 2 1/4 1/2
BLUE
BLACK
HND-A-1
BLACK
REDGREENBLACK
GREEN
BLACK
GREENBLACK
BLUERED
GREEN
GREENBLACK
BLUE
BLACK
REDGREEN
7/8 1/2
1.48 1.57 0.76 3/8
1 1/4 1 3/4
121 to 175
APHE-A-2 96 to 120
HNDE-A-1 1 to 30HNDE-A-2 31 to 40HNDE-A-3 41 to 70
71 to 120
3001 to 4200HNDE-D-3 2241 to 3000HNDE-D-4
HNDE-D-2 1308 to 2240
HNDE-B-4 376 to 572
HNDE-C-3 573 to 745HNDE-C-4 746 to 1307
HNDE-B-2 166 to 235
176 to 320
HNDE-B-3 236 to 375
Model Load Range (lbs)
0.59 3/80.81 1.18APHE-A-1 1 to 95
1.10 .840.710.11
1.31
APHE-B-1APHE-B-2
HNDE-A-4
HNDE-B-1 121 to 165
1/4 1 1/8 1.311 1/4
HND-C-4 746 to 1307 BLACK
Isolator dimensions (inches)Color
5/8
6 3 1/4 4 4 1/2
1.34
HND-D-2 1308 to 2240 REDHND-D-3 2241 to 3000 GREENHND-D-4 3001 to 4200 BLACK
HND-B-4 376 to 572 BLACK
HND-C-3 573 to 745 GREEN
4 1/2 1 7/8 2 1/4 3HND-B-3 236 to 375 GREEN
176 to 320
HND-B-1 121 to 165 BLUEHND-B-2 166 to 235 RED
APH-B-1 121 to 175 GREEN1/2
GREENAPH-A-2 96 to 120 BLACK
2.41 3/81.29APH-A-1 1 to 95
Color
are subject to change without prior notice. Please consult your local rep. for updates.
Due to our policy of continual product development and improvement, all specifications
Model Load Range (lbs)Isolator dimensions (inches)
1.65 1.77
APH-B-2 BLACK
1 to 30
3 1 3/8
HND-A-4 71 to 120
HND-A-2 31 to 40
Spring Hangers
Features + Application Information1. Powder coated steel bracket (50-70 micron ASTM D4138-07a) 5. Consult spring chart on page 22 for isolator performance data2. Load distribution steel washer3. Nuts, washers & rods by others4. Spring elements color-coded for easy field verification
Dimensional + Model Selection Data (Refer to page 2 for isolator star rating system)
3/4" deflection seriesE
1" deflection seriesE
n/a2" deflection series
E
n/a
3" deflection seriesE
www.vimco.biz G-1010 Rev. 2 (page 13)
4-1/8"34°
H
HSB-141
Model
2083 to 2603HSD-159-161
1 to 80Load Range (lbs)
HSB-148A-146B
Load Range (lbs)
1691 to 2076
333 to 580
596 to 647
1 to 100
81 to 160161 to 310
648 to 11901191 to 15761577 to 1690
28°
n/a
H
5-5/8"
28°
HSB-147HSB-148A
HSB-147-146B
6-1/2"30°
HSE-182 101 to 150
n/a
HSE-184 211 to 332151 to 210
D1/2"1/2"5/8"5/8"3/4"3/4"
30°
23°
46°
28°
311 to 410411 to 595
H
HSE-187HSE-186 581 to 850
1471 to 1825HSE-186-199 1158 to 1470
851 to 1157
Model Load Range (lbs)
36 to 6516 to 35
HSF-043
HSB-109HSB-110
1251 to 1500HSD-159
HSB-112
1501 to 2082
HSB-142
911 to 10801081 to 1250
186 to 210211 to 300301 to 370
751 to 910HSB-111
HSA-127
HSB-140
ModelHSS-021
Load Range (lbs)
26 to 55HSS-022
371 to 700701 to 750
1.8"
1 to 25
3-1/8"
4-5/8"
HSS-023
HSD-158
HSA-124HSA-125HSA-126
HSS-024
HSF-041
HSF-044HSF-045
HSF-042
H
2.3"66 to 90
86 to 125
1 to 15
91 to 185
56 to 85
Hanger Series
Dimensions
HSB-143
A B C
HSF 3.47" 2.15" 1.5"
are subject to change without prior notice. Please consult your local rep. for updates.
Due to our policy of continual product development and improvement, all specifications
HSE-183
HSB-144HSB-141-146B
ModelHSE-181
HSE-187-199
HSE-185
HSS 2.72" 2.15" 1.5"
HSB 7-1/2" 3" 2-3/4"HSA 4-1/2" 3" 2-1/4"
HSE 8-3/4" 3-1/2" 2-3/4"HSD 6-3/8" 3-1/2" 2-3/4"
Neo-SpringTM Hangers
Features + Application Information1. Powder coated steel bracket (50-70 micron ASTM D4138-07a) 5. Ozone & water resistant elastomer elements with embedded2. Load distribution steel washer + embedded steel plates steel plates and incorporating projected collar to prevent metal3. High deflection, low natural frequency to metal contact between rod and bracket4. Spring / rubber elements color-coded for easy field verification 6. Consult spring chart on page 22 for isolator performance data
Dimensional + Model Selection Data (Refer to page 2 for isolator star rating system)
1.5" deflection seriesH 1 E
n/a2" deflection series
2.5" deflection seriesH 1 E
1-1/4"
n/a
(Refer to page 2 for isolator star rating system)
1" deflection series 3.5" deflection seriesH 1 H 2 E H 1 E
1-1/4"
www.vimco.biz G-1010 Rev. 2 (page 14)
3/4"HNSE-Dx 11-13/16" 4-1/8" 4"
1/2"HNSE-B/Cx 11-13/16" 4-1/8" 4" 5/8"HNSE-Ax 11-13/16" 4-1/8" 4"
28°
2.3" 23°
3-3/8" 46°
Model Load Range (lbs)HNSF-HM-041 1 to 15
3" 28°
n/a
28°
5/8"
4-5/8"
4-1/8"
3"
1" 5-5/8"HSB-HM-142 161 to 310
1/2"5/8"
HNSB-B/C/Dx 10-3/16" 4-1/2" 4"
30°
n/a
46°
28°
34°
28°
H 2
3-3/8"
H 2
5-5/8"
H 2
6-1/2"
1-3/4"
3"
1-1/4"
1-3/4"
1-3/4"
HSB-HM-112 1081 to 1250
HSB-HM-109 701 to 750HSB-HM-110 751 to 910
131 to 210HSB-HM-125 211 to 300
4-5/8"
HSB-HM-126 301 to 370HSB-HM-127 371 to 700
HSB-HM-111 911 to 1080
1"
HNSF-HM-045 91 to 185
HNSF-HM-042
HSB-HM-124
16 to 35HNSF-HM-043 36 to 65HNSF-HM-044 66 to 90
are subject to change without prior notice. Please consult your local rep. for updates.
Due to our policy of continual product development and improvement, all specifications
Hanger Series
DimensionsA B C D
3/8"HSB-HM 7-1/2" 3" 2-3/4" 3/8"
HNSF-HM 4.85" 2.15" 1.5"
2-3/4"HNSA-Bx 8" 3" 2-3/4"
HNSE-D2-159 1501 to 2082
1/2"HNSB-Ax 10-3/16" 4-1/2" 4"
HNSA-Ax 8" 3"
Model Load Range (lbs)
HNSB-C3-108 583 to 620
HNSA-A3-121 1 to 50HNSA-A4-122 51 to 80HNSA-B1-123 81 to 130HNSA-B2-124 131 to 210HNSA-B3-125 211 to 300HNSA-B3-126 301 to 370HNSA-B4-127 371 to 582
HNSB-C4-111 911 to 1080
HNSB-C4-109 621 to 750HNSB-C4-110 751 to 910
HNSB-C4-112 1081 to 1250
1 to 80HSB-HM-141 81 to 160HSB-HM-140
HNSE-D3-159-161 2083 to 2603
HNSE-D2-158 1251 to 1500
HSB-HM-143 311 to 410
1 to 80HNSB-B1-141 81 to 160
HSB-HM-144 411 to 595HSB-HM-147 648 to 1190
Model Load RangeHNSB-A4-140
411 to 595HNSB-C3-141-146B 596 to 647
HNSB-B3-142 161 to 310HNSB-B4-143 311 to 410HNSB-C3-144
648 to 1190HNSB-D2-148A 1191 to 1576
HNSB-D2-147-146B 1577 to 1690
HNSB-C4-147
HNSB-D2-148A-146B 1691 to 2076
Model Load Range (lbs)HNSE-A4-181 1 to 100
HNSE-B3-184 211 to 332
HNSE-B1-182 101 to 150
HNSE-C4-186 581 to 850HNSE-C4-187 851 to 1157
HNSE-C3-185 333 to 580
HNSE-B2-183 151 to 210
HNSE-D2-187-199 1471 to 18251158 to 1470HNSE-D2-186-199
Union/Screwed Connection, Rubber Expansion Joints
Features + Application Information1. Reduces noise and vibration transmission 7. Synthetic fiber reinforcement2. Eliminates stress due to thermal expansion and piping misalignment 8. Corrosion resistant materials3. Precision molded of synthetic rubber 9. Easy field installation4. Threading standard as per customer specifications (NPT, BSPT)5. Applicable fluids for standard construction: water (cold, hot or sea), weak acids, alkalis, compressed air etc.6. Different elastomers are available for other fluids (e.g. oil). Contact factory for technical assistance
Dimensional + Model Selection Data
FCU models (twin bellow) FCU series (twin bellow)Size Length Axial Axial Transverse Angular Operating Burst
L compression elongation deflection deflection pressure pressure
(inches) (inches) (inches) (inches) (inches) (deg) (psig) (psig)
1/2 8 7/8 1/4 7/8 30° 150 7003/4 8 7/8 1/4 7/8 30° 150 7001 8 7/8 1/4 7/8 25° 150 700
1 1/4 8 7/8 1/4 7/8 25° 150 7001 1/2 8 7/8 1/4 7/8 20° 150 700
2 8 7/8 1/4 7/8 15° 150 700Materials (see figure) Ratings indicated above are for constant pressures at 100°F. For pulsating pressures use 1/2 of
No. rating; for surge pressures use 1/6 of rating. For elevated temperature ratings, consult factory.
1 Expansion joints must be installed per FSA technical handbook guidelines.
23
FCU-T / FCU-TH models (twin bellow) FCU-T series (twin bellow)Size Length Axial Axial Transverse Angular Operating Burst
(F/F) compression elongation deflection deflection pressure pressure
(inches) (inches) (inches) (inches) (inches) (deg) (psig) (psig)
1/2 8 7/8 1/4 7/8 30° 232 7253/4 8 7/8 1/4 7/8 30° 232 7251 8 7/8 1/4 7/8 25° 232 725
1 1/4 8 7/8 1/4 7/8 25° 232 7251 1/2 8 7/8 1/4 7/8 20° 232 725
2 8 7/8 1/4 7/8 15° 232 725FCU-SH models (single bellow) FCU-TH series (twin bellow)
Size Length Axial Axial Transverse Angular Operating Burst
(F/F) compression elongation deflection deflection pressure pressure
(inches) (inches) (inches) (inches) (inches) (deg) (psig) (psig)
1/2 6.30 3/5 2/5 3/5 20° 355 10663/4 6.30 3/5 2/5 3/5 20° 355 10661 6.30 3/5 2/5 3/5 20° 355 1066
1 1/4 8.35 3/5 2/5 4/5 30° 355 10661 1/2 8.35 3/5 2/5 4/5 30° 355 1066
2 8.78 3/5 2/5 4/5 30° 355 1066Materials (see figures) FCU-SH series (single bellow)No. Size Length Axial Axial Transverse Angular Operating Burst
1,2 (F/F) compression elongation deflection deflection pressure pressure
3,4 (inches) (inches) (inches) (inches) (inches) (deg) (psig) (psig)
5 1/2 5.12 5/16 5/32 5/16 15° 355 10666 3/4 5.12 5/16 5/32 5/16 15° 355 10667 1 5.12 5/16 5/32 5/16 15° 355 10668 1 1/4 5.35 5/16 5/32 5/16 15° 355 1066
1 1/2 5.35 5/16 5/32 5/16 15° 355 10662 5.98 5/16 5/32 5/16 15° 355 1066
Ratings indicated above are for constant pressures at 100°F. For pulsating pressures use 1/2 of
rating; for surge pressures use 1/6 of rating. For elevated temperature ratings, consult factory.
Expansion joints must be installed per FSA technical handbook guidelines.
www.vimco.biz G-1010 Rev. 2 (page 15)
FCU-SH-7FCU-SH-10FCU-SH-12FCU-SH-15
Model
FCU-SH-5
BoltsReinforcing fabric
are subject to change without prior notice. Please consult your local rep. for updates.
Due to our policy of continual product development and improvement, all specifications
PolyesterZinc plated carbon steel
FCU-SH-20
Model
FCU-5FCU-7
FCU-10FCU-12FCU-15FCU-20
Model
FCU-T-5FCU-T-7
FCU-T-10FCU-T-12FCU-T-15FCU-T-20
Model
FCU-TH-5FCU-TH-7
FCU-TH-10FCU-TH-12FCU-TH-15FCU-TH-20
Threaded union Cast SUS 201EPDMZinc plated carbon steel
Cast SUS 201MaterialPart
FlangesNutsTube
Part
Tube EPDM
MaterialUnion Malleable ironReinforcing fabric Polyester
Temp.
range
(°F)
-4 to 212-4 to 212-4 to 212-4 to 212-4 to 212-4 to 212
Temp.
range
(°F)
14 to 15814 to 15814 to 15814 to 15814 to 15814 to 158
Temp.
range
(°F)
14 to 15814 to 15814 to 15814 to 15814 to 15814 to 158
Temp.
range
(°F)
14 to 15814 to 15814 to 15814 to 15814 to 15814 to 158
Flanged Connection, Rubber Expansion Joints
Features + Application Information1. Reduces noise and vibration transmission 7. Synthetic fiber reinforcement2. Eliminates stress due to thermal expansion and piping misalignment 8. Corrosion resistant materials3. Precision molded of synthetic rubber 9. Easy field installation4. Floating flanges drilling standards as per customer specifications (ANSI, BS, DIN, JIS)5. Applicable fluids for standard construction: water (cold, hot or sea), weak acids, alkalis, compressed air etc.6. Different elastomers are available for other fluids (e.g. oil). Contact factory for technical assistance
Dimensional + Model Selection Data
Materials (see figures) Control unit composition:No.1
234
Pipe Axial Axial Transverse Angular Axial Axial Transverse Angular
Size L D F compression elongation deflection deflection compression elongation deflection deflection PSIG(inches (inches) (inches) (inches) (inches) (inches) (inches) (deg) (inches) (inches) (inches) (deg) 215
1151 1/4 6 1.58 2.72 1/2 3/8 1/2 15° 0.31 0.15 0.31 15° 3621 1/2 6 1.58 2.72 1/2 3/8 1/2 15° 0.31 0.15 0.31 15° 232
2 6 2.05 3.39 1/2 3/8 1/2 15° 0.31 0.19 0.31 15° 2272 1/2 6 2.68 4.18 1/2 3/8 1/2 15° 0.47 0.23 0.39 15° 113
3 6 3.00 4.57 1/2 3/8 1/2 15° 0.47 0.23 0.39 15° 3554 6 4.06 5.91 5/8 3/8 1/2 15° 0.70 0.39 0.47 15° 2275 6 5.04 7.09 5/8 3/8 1/2 15° 0.70 0.39 0.47 15° Ratings indicated above are for constant
6 6 5.99 8.23 5/8 3/8 1/2 15° 0.70 0.39 0.47 15° pressures at 100°F. For pulsating
8 6 7.64 10.24 5/8 3/8 1/2 15° 0.98 0.55 0.86 15° pressures use 1/2 of rating; for surge
10 8 9.85 12.60 3/4 1/2 3/4 15° 0.98 0.55 0.86 15° pressures use 1/6 of rating. For elevated
12 8 11.82 14.45 3/4 1/2 3/4 15° 0.98 0.55 0.86 15° temperature ratings, consult factory.
14 8 12.60 16.07 3/4 1/2 3/4 15° 0.98 0.62 0.86 15° Operating temp. range16 8 14.65 18.59 3/4 1/2 3/4 15° 0.98 0.62 0.86 15°
18 8 16.34 20.56 3/4 1/2 3/4 15° 0.98 0.62 0.86 15°
20 8 17.88 22.45 3/4 1/2 3/4 15° 0.98 0.62 0.86 15°
24 10 22.45 27.40 3/4 1/2 3/4 15° 0.98 0.62 0.86 15°28 10 26.77 31.49 3/4 1/2 3/4 15° 0.98 0.62 0.86 15°
1 1/2 7 1.58 2.72 2 3/4 1 3/4 35° 1 3/5 1 30° Control Units2 7 2.05 3.39 2 3/4 1 3/4 35° 1 3/5 1 30°
2 1/2 7 2.68 4.18 2 3/4 1 3/4 35° 1 3/5 1 30°
3 7 3.00 4.57 2 3/4 1 3/4 35° 1 3/5 1 30°
4 9 4.06 5.91 2 1 1 1/2 35° 1 3/4 3/4 30° Control units must be installed on
5 9 5.04 7.09 2 1 1 1/2 35° 1 3/4 3/4 30° unanchored systems or when test /
6 9 5.99 8.23 2 1 1 1/2 35° 1 3/4 3/4 30° surge / operating pressure exceeds
8 13 7.64 10.24 2 1/4 1 1 1/4 30° 1 3/4 3/4 30° the rating below:
10 13 9.85 12.60 2 1/4 1 1 1/4 30° 1 3/4 3/4 30°
12 13 11.82 14.45 2 1/4 1 1 1/4 30° 1 3/4 3/4 30°
14 14 12.60 16.07 1 1/2 3/4 1 1/4 20° 3/4 3/4 3/4 20°
16 14 14.65 18.59 1 1/2 3/4 1 1/4 20° 3/4 3/4 3/4 20°
18 14 16.34 20.56 1 1/2 3/4 1 1/4 20° 3/4 3/4 3/4 20°
20 14 17.88 22.45 1 1/2 3/4 1 1/4 20° 3/4 3/4 3/4 20° Expansion joints must be installed per
24 14 22.84 27.17 1 1/2 3/4 1 1/4 20° 3/4 3/4 3/4 20° FSA technical handbook guidelines.
www.vimco.biz G-1010 Rev. 2 (page 16)
FCT-240-H
2up to 8"Size Units / Joint
FCT-140-H
FCT-160-H
FCT-180-H
FCT-200-H
FCT-80-H
FCS models (single bellow)
FCT-180
FCT-200
FCT-240
Dimensions
Reinforcing fabric
Galvanized steel (drilling available as per ANSI/BS/DIN/JIS)Carbon steel wire strand
PartFlange
4
CRU models (control units)
2
FCT models (twin bellow)
Item Quantity12
MaterialTie Rod
Reinforcing ringTube
Polyester
are subject to change without prior notice. Please consult your local rep. for updates.
Due to our policy of continual product development and improvement, all specifications
Steel / Rubber washer
FCT-60
FCT-80
FCT-100
FCT-120
GussetNutsEPDM
FCT-60-H
FCT-Hup to 12"14" to 24"
FCT-50 FCT-50-H
FCS-180
FCT-100-H
FCT-120-H
FCT-140
FCT-160
FCS-160 FCS-160-H
FCS-100 FCS-100-H
FCS-140-H
Model
FCS-15 14" to 28"FCS-H
up to 12"FCS-15-H
FCT-40 FCT-40-H
FCT-20
FCT-25
FCT-30 FCT-30-H
FCT-20-H
FCT-25-H
Model
FCT-15
FCT
FCT-15-H
FCS-25-H
FCS-30 FCS-30-H
FCS-40 FCS-40-H
FCS-240-H
14" to 24"
FCS-280
FCS-180-H
FCS-280-H
FCS-140
FCS-80-H
FCS-200-H FCS-H
FCS-25
FCS-240
Twin Bellow: FCT series
Operating pressureSeries Size
FCSup to 12"14" to 28"
FCT-H series
FCS-200
16" thru 24" 45 psig
10" to 24" 4
5" thru 10" 135 psig12" thru 14" 90 psig
Size Pressure
Series °F
FCS-20 FCS-20-H
FCS-50-H
FCS-120 FCS-120-H
FCS-60 FCS-60-H
up to 12"
FCS-80
Single Bellow: FCS series FCS-H seriesFCS-12 FCS-12-H
FCS-50
up to 4" 150 psig
FCS 14 to 24014 to 194
FCT -4 to 212FCT-H 14 to 170
Stainless Steel Expansion Joints
Features + Application Information1. Reduces noise and vibration transmission 5. Corrosion resistant materials2. Vibration absorption and piping misalignment correction 6. Easy field installation3. Eliminates stress due to thermal expansion and piping misalignment4. Engineered bellow design ensures equal stress distribution through entire length
Dimensional + Model Selection Data
JF-500-T models JF-500-T series (threaded connection)Totallength
(inches)
10
10
10
10
12
12
Materials (see figure) Pressure ratings indicated above are based on 68°F ambient temperature. For elevatedNo. temperature ratings, consult factory.123
JF-500 / JF-500-H models JF-500 / JF-500-H series (flanged connection)Totallength
(inches)
6
6
6
6
6
6
8
8
89
6
6
6
6
6
6
8
8
8
9
Materials (see figure) Pressure ratings indicated above are based on 68°F ambient temperature. For elevatedNo. temperature ratings, consult factory.1223
www.vimco.biz G-1010 Rev. 2 (page 17)
JF-500-T-7
JF-500-T-10
JF-500-T-12
are subject to change without prior notice. Please consult your local rep. for updates.
Due to our policy of continual product development and improvement, all specifications
JF-500-H-30
JF-500-H-50
JF-500-H-80
JF-500-H-120
JF-500-T-15
Model
JF-500-T-5
JF-500-T-20
JF-500-120
JF-500-H-20
3/4
1
1 1/4
1 1/2
JF-500-80
JF-500-30
JF-500-50
5
8
12
Nominalbore
(inches)
1/2
2.762
12
2
8
3
5
3.99
9.21
2.75
1.06
1.28
1.81
2.20
BellowsO.D.
(inches)
0.75 ± 0.60
Axialmovement
(inches)
.59± 0.60
± 0.60
± 0.60
± 0.60
± 0.60
.78
.78
.70
.62
Max. lateraloffset
(inches)
.78
Operatingpressure
(psi)
300
-122 to +780300
300
300
300
300
-122 to +780
-122 to +780
-122 to +780
-122 to +780
Temp.range
(°F)
-122 to +780
PartBellowsBraidsTube end
JF-500-20 2
DescriptionSUS304 (SUS316 option)
SUS304
SUS304
Model Nominal
2.75 ± 0.60 .59 150
JF-500-25 2 1/2 3.40 ± 0.60
-122 to +780
.55 150 -122 to +780
JF-500-40 4 5.03 ± 0.60 -122 to +780
± 0.60 .47
-122 to +780
150
.31 150
-122 to +780
.39 150
JF-500-60 6 7.22 ± 0.60 .23 150 -122 to +780
6.16 ± 0.60
± 0.60 .31 150
.19 15013.42 ± 0.60
-122 to +780
JF-500-100 10 11.37 ± 0.60 .23 150 -122 to +780
JF-500-140 14 15.43 ± 0.60-122 to +780
.19 150 -122 to +780
JF-500-H-25 2 1/2 3.40 ± 0.60 -122 to +780
± 0.60 .59
-122 to +780
370
.47 370
-122 to +780
.55 370
-122 to +780
3.99 ± 0.60
JF-500-H-40 4 5.03 ± 0.60
3
.31 370
.39 370
-122 to +780
JF-500-H-60 6 7.22 ± 0.60 .23 370 -122 to +780
6.16 ± 0.60
-122 to +780
JF-500-H-100 10 11.37 ± 0.60 .23 370 -122 to +780
9.21 ± 0.60
-122 to +780
13.42 ± 0.60 .19 370
Max. lateral Operating
JF-500-H-140 14 15.58 ± 0.60 .19 370
.31 370
Temp.bore O.D. movement offset pressure range
Bellows Axial
(inches) (psi) (°F)
Part Description
(inches) (inches) (inches)
-122 to +780
Bellows SUS304 (SUS316 option)
Flange AISI 1015 (SUS304 option)
Tie Rods S25C
Gasket Rubber
Floating Floors
Features + Application InformationVIMCO floating floors provide a solution to the problem where the transmission loss of the standard structural floor is not sufficientto prevent noise from passing from mechanical rooms to noise-sensitive areas above or below it. Floating floors primarilycontrol airborne sound transmissions; they are not intended to be used in place of vibration isolators and/or inertia bases.
VIMCO floating floors perform acoustically on the sameprinciple as a double-glazed window : The separation of themasses, with an air gap, gives a much greater transmissionloss than if the two masses are combined into a continuousfloor. The "enclosed air cavity" is the primary isolator.
Vibration Management Corporation prefers and recommends a form-work floating floor construction over the lift slab / jack-upsystem offered by other manufacturers.
All types of floating floor construction perform the same acoustically as long as the dynamic natural frequency of the isolationmount, the air gap, and masses are the same. The choice of construction method therefore depends on economy, reliability, andease of installation. Jack-up system manufacturers generally claim lower installed costs. This cost differential tends to disappearthough, for larger areas where many equipment are supported on the floor, or where many plinths project through the floating floorfor equipment, piping support. In both cases the number of canisters has to be increased to provide proper edge and weightsupport. Most jack-up systems are designed for a 4" floating floor, with thicker slabs resulting in higher costs, not only due toextensions required on the canisters, but again in causing canister spacing to decrease. The VIMCO form-work system easilyaccommodates thicker floating floors with correct isolator selection. The form-work construction also offers the provision of afiberglass infill which in addition to preventing a sound tunneling effect, provides extra transmission loss. Independent lab tests bya competitor show that a 2" air gap with fiberglass infill gives a STC rating increase equivalent to doubling the air gap to 4" !!!
MaterialsVIMCO's form-work floating floor systemconsists of the following materials :
1. Roll-out isolation material provided with neoprene pads2. Closed cell perimeter isolating boards3. Plywood / cement board form-work4. Polyethylene bond-breaker sheeting5. Polyurethane perimeter sealant6. Neoprene contact adhesive7. Floating floor isolated drains8. Neoprene high load pads
VNRM-xx (xx denotes pad spacing in inches): Roll-out isolation materialVIMCO roll-out isolation material consists of low-density fiberglass with 2" high, resilient, neoprene isolation pads, embedded at24" centers as standard. Closer spacing between pads can be factory installed, or achieved at site using additional high load pads.VPPI-xx (xx denotes height in inches): Perimeter isolating boardsVIMCO incorporates closed cell expanded polyethylene sheets for perimeter isolation. These sheets have excellent weather-resistant characteristics and aid in preventing flanking noise along the edges of the floating floor area, by completing the isolationof the floating floor from the building structure.VNHP : High load padsVIMCO provides individual neoprene isolation pads for areas with additional, uneven loading. These pads can be factory installedwith the roll-out isolation material or can be furnished separately for installation at site, by a VIMCO authorized representative.VID-xx (xx denotes drain inlet size in inches): Isolated drainsVIMCO floating floor isolated drains consist of a two member housing, to drain water from the floating floor down to existingdrainage piping system, without compromising the structural isolation.Ancillary materials :Depending on economic considerations, local availability, the following materials may either be supplied by VIMCO or sourcedby your local VIMCO representative. Materials must however comply to VIMCO specifications to ensure proper installation.
Plywood / Cement board Neoprene spray adhesivePolyethylene sheeting Polyurethane sealant
www.vimco.biz G-1010 Rev. 2 (page 18)are subject to change without prior notice. Please consult your local rep. for updates.
Due to our policy of continual product development and improvement, all specifications
VIMCO form-work floating floor
Air Mounts
Features + Application Information1. Air-cushioned isolation 5. Heavy wall construction2. Low natural frequency (3~5 Hz at operating load) 6. High lateral stability3. High deflection 7. Low maintenance4. Neoprene padded top and bottom base 9. Combined resiliency and air prevents drift or permanent set
Dimensional + Model Selection Data (Refer to page 2 for isolator star rating system)
AMA models AMA series
A B C D E0.47 1.97 3.94 3.90 3.100.47 2.36 3.94 3.90 3.100.47 3.54 5.43 3.90 3.100.47 4.33 6.46 3.90 3.100.55 5.91 8.35 3.90 3.100.55 9.45 12.36 3.90 3.100.55 12.99 16.22 3.90 3.10
Roof Curb Isolation Rails
Features + Application InformationVIMCO model AR aluminum spring rails are specifically designed and engineered as a vibration control system for curb mounted equipmentinstalled on the roof. The rails are custom designed to fit between standard roof curb and equipment, providing continuous support and an airand watertight seal. The system is adaptable to all curb systems and equipment without any modifications to either curb or equipment. Theassembly provides a cost effective method of providing vibration control for rooftop equipment in a lightweight and weatherproof unit.1. Construction - "Heavy wall" aluminum extrusion2. Sizes - 84" x 180" and smaller shipped in one piece. Units up to 85" x 450" shipped with splice kits for field assembly3. Springs - spaced and selected to provide uniform deflection after equipment is installed4. Corners - mitered and continuously welded exterior surface for complete weatherability5. Seal - weatherproof gasket is not exposed to elements. This eliminates deterioration of material6. Curb cap - flat bottom design adapts to all curb configurations7. Available in 1" and 2" deflectionsOptionsCable restraintsPictorial DescriptionTypical installation Cutaway view Section
Other Bases / Curbs
Cooling tower rails.Structural steel fan bases.** NEW ** Isolation curbs (roof curbs with integral spring isolators) now available. Contact factory for details.
www.vimco.biz G-1010 Rev. 2 (page 19)Due to our policy of continual product development and improvement, all specifications
are subject to change without prior notice. Please consult your local rep. for updates.
Model Load Range (lbs)Part Dimensions (inches)
AMA-4 200 to 400
AMA-15 800 to 1500
AMA-45
Bolt Size
AMA-2 100 to 200 M10 x 40M12 x 50
AMA-8 400 to 800 M12 x 50M12 x 50
AMA-25 1400 to 2500 M16 x 60
Materials:
2400 to 4500 M16 x 60AMA-75 4000 to 7500 M16 x 60
Environmental Data -20 °F to + 180 °F
Resilient Element NeopreneMetal Structure Structural Steel
Bolted Inertia Bases
Features + Application InformationVIMCO model BIB bolted inertia bases are constructed of factory formed steel members. The modular construction design allows 6" intervallengths/widths and all standard thickness (4", 6", 8", 10", 12"). Inertia base components are supplied loose as standard for easy shipping andtransportation at jobsite. Bases can also be supplied fully assembled as an option. VIMCO offers free of cost engineering services to size baseand reinforcement per VIMCO / industry guidelines or project specifications. Job specific submittals are provided for each base, detailingload calculations and itemized component bill of materials. Standard design guidelines are: 1. Minimum 1:1 ratio between inertia base weight and equipment weight2. Base thickness shall be minimum 8% of the longest span between isolators3. Concrete reinforcement by 1/2" rebar at 8" center to center spacing4. (4) Adjustable height saving isolator mounting brackets supplied as standard5. Inertia bases are designed for post-drill concrete anchor boltsOptions(8) isolator mounting brackets instead of (4)T shaped basesPreassembled shipment
Pictorial DescriptionIso view Plan view Section
Welded Inertia Bases
Features + Application InformationVIMCO model IB inertia bases are specifically designed and engineered to receive poured concrete, for use in supporting mechanicalequipment requiring a reinforced concrete inertia base. Bases are available in 6", 8", 10" 12" thicknesses. VIMCO offers free of costengineering services to size base and reinforcement per VIMCO / industry guidelines or project specifications. Standard design guidelines are: 1. Minimum 1:1 ratio between inertia base weight and equipment weight2. Base thickness shall be minimum 8% of the longest span between isolators3. Concrete reinforcement by 3/8" rebar at 8" center to center spacing4. Height saving isolator mounting brackets supplied as standard5. Inertia bases are designed for post-drill concrete anchor boltsOptionsAnchor bolts or anchor bolt templates(6), (8) isolator mounting brackets instead of (4)T shaped bases
Pictorial DescriptionIso view Plan view Section
www.vimco.biz G-1010 Rev. 2 (page 20)Due to our policy of continual product development and improvement, all specifications
are subject to change without prior notice. Please consult your local rep. for updates.
Seismic Snubber
Features + Application InformationVIMCO model SNB3-3050 is an all-directional (3-axis) device designed to restrain and decelerate motion of resiliently mountedequipment resulting from external loads or seismic activity, to acceptable limits. The device consists of interlocking welded steelmembers, separated by a molded neoprene insert. Neoprene element is designed to prevent direct metal to metal contact between2 steel members, and provide a minimum of 3/4" snubbing material in all directions. Device is manufactured to allow freeunrestricted movement of equipment of not less than 1/8", limited to a maximum of 1/4" before coming in to contact with energyabsorbing neoprene insert. Design also allows for removal of neoprene element for visual inspection and/or replacement.
Dimensional + Model Selection Data
Seismic Cable Restraint SystemApplication Information1. For permanent attachment of cable brace to structure / equipment / hanger2. Designed for use with 7x19 strand core pre-stretched galvanized aircraft cableSCRS models SCRS series
DIA. Code Size(") 04 3/8"
4-5/16 2 SC-01 1/8 975 05 1/2"5 2-1/4 SC-02 3/16 2050 06 5/8"5 2-5/8 SC-03 1/4 3150 07 3/4"
Features:Typical installation details 1. Quick installation (no shackles, thimbles, u-bolts, clevis angles....)
2. Cable easily slides into oversized front arch opening3. Breakaway hex nuts assure verification of proper installation4. Will swivel to final installation angle5. Low carbon steel, electro-galvanized finish6. Maximum load rating based on cable breaking strength
While ordering specify rod/bolt size code in place of "xx" e.g. for 1/8" cable with 3/8" bolt order SCRS-01- 04
SCRSA models SCRSA series
Model DIA. Code Size Code SizeSC-00 3/32" 600 02 1/4" 07 3/4"SC-01 1/8" 1100 04 3/8" 08 7/8"SC-02 3/16" 2667 05 1/2" 10 1"SC-03 1/4" 4400 06 5/8" 12 1-1/4"
Typical connection details Features:1. Complies with ASCE 19 and SMACNA Restraint Manual as required by FEMA, NEHRP, IBC, OSHPD, UNC, BOCA, SBCCI, other Building Codes2. Permanent end fitting3. Maintains break strength of cable and does not require thimbles4. (2) SCRSA's can be stacked on single rod to make a 4-way brace 5. Simple installation6. Maximum load rating based on cable breaking strength7. Supplied with 1 or 2 oval sleeves (depending on application)
www.vimco.biz G-1010 Rev. 2 (page 21)
SCRSA-03-xx 1/4" to 1-1/4"
Connection to structureConnection to equipment Connection to structure
Rod/Bolt codesModel
Rod / Bolt size (")
Cable Max Design Load
are subject to change without prior notice. Please consult your local rep. for updates.
Due to our policy of continual product development and improvement, all specifications
While ordering specify rod/bolt size code in place of "xx" e.g. for 3/32" cable with 3/8" bolt order SCRSA-00- 04
/ support member (concrete deck) (steel beam)
Model
Part Dimensions (inches)
SCRS-02-xx 3/8" to 3/4"
SCRS-01-xx 3/8" to 3/4"
SCRSA-02-xx 1/4" to 1-1/4"
SCRS-03-xx 3/8" to 3/4"
SCRSA-00-xx 1/4" to 1-1/4"
SCRSA-01-xx 1/4" to 1-1/4"
Rod/Bolt
ROD / BOLT A B Model
Cable Max Design Load (lbs)
MAXIMUM APPROVED LOADS:HORIZONTAL: 3050 lbs
VERTICAL: 3050 lbs
Springs
Features + Application Information1. High deflection, low natural frequency2. Springs should be selected in the range of minus 30% to plus 25% of rated load (RL)3. Springs electrogalvanized in accordance with ASTM B633-13 Type II, Class 2
Dimensional + Model Selection Data (Refer to page 2 for isolator star rating system)
SL: Load at which spring will become solid or theoretical maximum loadRL: Rated load based on ASHRAE defined 50% additional travel to solid
FSH: Free spring height
www.vimco.biz G-1010 Rev. 2 (page 22)
Deflection at SL(inches)
Spring constant(lb/inch)
RL(lbs)
SL(lbs)Main Stripe
ColorSpring no.
are subject to change without prior notice. Please consult your local rep. for updates.
Due to our policy of continual product development and improvement, all specifications
045101102103104105
110111
1 1/4
1 1/4 2 1/4
1 1/2
5
2
1 5/32
2 2 3/4
4
2
1 1/4
2 1/2
1 5/16
041042043044
106107108109
021022023024
112113121122123124125126127140141142143144147
148A146B150151152153154155156157158159161181182183184185186187199 SILVER
SILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVER
BLUERED
YELLOWWHITEBLUERED
YELLOWWHITEPINKPINK
BLACKBLUE
YELLOWBROWN
REDPURPLEORANGEGREENGRAYWHITEGOLD
NILBLUE
ORANGEBROWNBLACK
YELLOWRED
GREENBLUE
BLACKRED
GREENGRAYWHITE
YELLOWWHITE
BROWNORANGEGREEN
REDBLACKWHITEGRAYBLUEGOLD
NILREDPINK
GREENBLUE
YELLOWBROWN
REDWHITEBLACK
204470
10015335776
1485676
113150216300400500600733866
10004664066
11017324630056066
133250333476953
126140083
150216300400500600733
1200166641686
133180266486713926533
3066
105150235086
11522285
115170225325450600750900
11001300150070060
100165260370450840100200375500714
14301892600125225325450600750900
110018002500625130200270400730
10701390800
0.750.750.750.75
1.401.301.30
1.541.481.391.33
1.301.201.201.201.101.000.800.801.001.001.301.301.201.000.800.501.152.252.252.002.002.002.002.002.001.301.301.201.201.201.101.000.901.001.001.004.304.003.603.203.603.003.003.00
6189
131
15346287
174271375500682900
1375162515007004777
1382604639007314589
188250357715946
682900
30097
174271
267
305075
125
3 5/8
200350464
122318002500625
375500
GALVANIZED STEEL SPRINGS
Rating
168
4088
140200
1.33
O.D. FSH
2 1/2
1 11/16
6
LIMITED WARRANTY
Subject to terms and conditions herein, Vibration Management Corporation ("VIMCO") warrants to the original ownerat the original installation site that products manufactured by VIMCO ("Products") comply, at the time of manufacture,with VIMCO literature, and will be free from defects in materials and workmanship for a period of 12 months after thedate of start-up or 18 months after the date of shipment from factory, whichever shall be less (the "Warranty Period")
REMEDYA. The sole remedy for breach of this warranty is expressly limited to either the repair / ex-factory replacement, or
refund of VIMCO ex-factory sale price (at VIMCO's sole option), of any Product found to have manufacturingdefects under conditions of normal use within the Warranty Period. Installation is not included.
B. The owner must notify the original installer of the Product and VIMCO (Attn: Warranty Claims, 5930 Thomas RoadHouston, TX 77041), in writing, within the Warranty Period, providing a detailed description of all claimed defects.Transportation to factory or other designated facility for repairs of any Products or components of Products allegeddefective shall, in all events, be the responsibility and at the cost of the owner.
EXCLUSIONSVIMCO shall have no liability for:A. Incidental, special or consequential damages such as loss of the use of products, facilities or production,
inconvenience, loss of time or labor expense involved in repairing or replacing the alleged defective Product.B. The performance of any Product under conditions varying materially from those under which such Product is
usually tested under industry standards as of the time of shipment.C. Any damage to the Product due to abrasion, erosion, corrosion, deterioration, abnormal temperatures or the
influence of foreign matter or energy.D. The design or operation of owner's plant or equipment or of any facility or system of which any Product
may be made a part.E. The suitability of any Product for any particular application.F. Any failure resulting from misuse, modification not authorized by VIMCO in writing, improper installation
or lack of proper maintenance.G. Equipment furnished by owner, either mounted or unmounted, or when contracted for by the owner to be
installed or handled.
VIMCO's liability under this warranty shall not in any case exceed the VIMCO ex-factory sale price for the Productfound to be defective.
THIRD-PARTY WARRANTIESFor goods or components not manufactured by VIMCO, above mentioned warranty obligations of VIMCO shall be limitedby the warranty actually extended to VIMCO by its vendors.
SEVERABILITYTo the extent that any provision of this warranty would be void or prohibited under applicable law, such provisions shall be limited in effect to the minimum extent necessary to render the remaining provisions hereof enforceable.
NO OTHER WARRANTIESVIMCO makes no implied warranty of merchantability or fitness for particular purpose, or other warranties with respectto any products or services except as expressly set forth in this limited warranty.
www.vimco.biz G-1010 Rev. 2 (page 23)
T: +1-713-460-VIMCO F: +1-713-460-1100 E: [email protected] +1-713-460-8462
Houston - Texas 77041, USA