introduction - centurylink

1

Congratulations! You have purchasedone of the most sophisticated cordlesstelephones on the market! The QW1734has been designed to offer a newstandard in cordless telephonetechnology.

Unlike most other cordless phones,the QW1734 digitizes your voice usingadvanced digital voice coding to providenoise and distortion free performance.In most conditions you will not be able totell you are using a cordless phone.Gone are the annoyances of static,interference and having to listen to otherpeople’s conversations on your cordlessphone.

The QW1734 scrambles your voicebefore it transmits it. This allows you thesecurity of knowing that no one can tunein and eavesdrop on your conversations.

The QW1734 decodes and displaysname and number Caller ID (CID)information where available and whensubscribed to. The alpha-numericdisplay will show both the name andnumber of the calling party (whenavailable). Up to 15 name charactersand/or 11 phone number digits can bedisplayed on the LCD.

With the QW1734, the user can easilyanswer a call by pressing any key otherthan the OFF, VOLUME keys or 3Services keys. In addition, the handsetkeypad and LCD illuminate while thehandset rings to signal an incoming call.This is very useful in a dark environment.

The QW1734 includes aSpeakerphone and keypad on the BaseUnit. This enables you to make andreceive calls hands-free at the Base. In

INTRODUCTION

addition, the Intercom feature allowstwo-way communication between theHandset and Base Unit. PressingINTERCOM on the Base can also assistyou in locating a misplaced Handset.

The QW1734 uses special memory inboth the Base Unit and Handset which isnot susceptible to power failures. Thisprovides permanent storage of all speeddial numbers, CID information as well asthe Base Unit and Handset securitycodes.

When a spare battery(not included) isinstalled in the Base Unit, the QW1734uses this battery to provide operationalbackup in case of power failure. In thisway, you have access to all normalphone functions during a total poweroutage. Calls can still be placed andreceived without interruption. More than4 hours backup will be possible with afully charged battery in the Base Unit.

The phone will also alert you whenyou are Out of Range even when you'renot using the phone!

2

SPECIAL FEATURES• 900 MHz Operation.• Direct Sequence Spread Spectrum

- Digital Cordless Telephone.• Digitally-Scrambled Voice

Communication.• Simultaneous display of Name,

Number, and Time/Date stamp forCaller ID.

• 50 Caller ID memory locations.• Voice announce Caller ID• 4-row by 16-character dot matrix

alphanumeric display.• Backlit display on handset.• Backlit handset keypad.• Three Soft Keys which allow the user

to access different functions,depending on which mode the phoneis currently in (i.e. Caller ID, MemoryProgramming, etc.).

• Smart Dialing from Caller ID memoryeliminates the need to pre-programyour local area code.

• 25 locations Programmable Memoryfor 16-Digit Phone Number. Eachlocation can also be assigned up toa 15 character name.

• Out of Range indication while thehandset is in use or in standby mode.

• Handset speakerphone.• Speakerphone and keypad on the

Base Unit.• Two-way intercom between Handset

and Base Unit.• Removable handset battery pack.• Spare battery charger in the base

unit.• Complete battery back-up in case of

power failure (with additional batterypack installed in base).

• Face up or down Handset charging.• Easy answer - When the phone

INTRODUCTION

rings, simply press any key otherthan OFF, the Volume keys or the3 Services keys on the handset toanswer.

• Pressing the OFF key on handsetduring incoming ring will stop theringing.

• Auto hang up when returning thehandset to the base cradle.

• 24-Bit Digital Security Code.• Low Battery Detect and Warning

indicator.• Tone or Pulse dialing.• Visual Message Waiting Indication

(VMWI) for use with voicemailservice.

• Up to 7 hours of continuous talk timeor 14 days standby time.

• 8-level Volume control on Handset.• Programmable Ringer Tones and

Volume.• Headset Compatible, for use with

2.5mm headsets.

This manual is designed to familiarizeyou with the QW1734. We stronglyrecommend you read the manual beforeusing your phone.

3

PARTS CHECK LIST

1.Base Unit, Handset, Belt Clip and AC adapter2.One-Line Telephone Cord

3.Battery Pack4.Wall mount accessory

INTRODUCTION

4

FCC REGULATIONS

This equipment complies with Parts15 and 68 of the FederalCommunications Commission (FCC)rules for the United States. Operation issubject to the following two conditions:(1) this device may not causeinterference, and (2) this device mustaccept any interference, includinginterference that may cause undesiredoperation of the device.

The underside of the Base Unitcontaining engravements of either theFCC registration number and RingerEquivalence Number (REN), or the ICregistration number . You must, uponrequest, provide this information to yourlocal telephone company.

This equipment is compatible withinductively coupled hearing aids.

Should you experience trouble withthis telephone equipment, pleasecontact:

Customer Service at 800-651-6791

The telephone company may ask youto disconnect this equipment from theline network until the problem has beencorrected.

FCC Part 15

Warning: Changes or modificationsto this unit not expressly approved bythe party responsible for compliance'scould void the user’s authority to operatethe equipment.

The equipment has been tested andfound to comply with part 15 of the FCC

rules. These limits are designed toprovide reasonable protection againstharmful interference in a residentialinstallation. This equipment generates,uses and can radiate radio frequencyenergy and, if not installed and used inaccordance with the instructions, maycause harmful interference to radiocommunications. However, there is noguarantee that interference will not occurin a particular installation. If thisequipment does cause harmfulinterference to radio or televisionreception, which can be determined byturning the equipment off and on, theuser is encouraged to try and correct theinterference by one or more of thefollowing measures:

- Reorient or relocate the receivingantenna.

- Increase the separation between theequipment and receiver.

- Connect the equipment into an outletor on a circuit different from that towhich the receiver is connected.

- Consult the dealer or an experiencedradio/TV technician for help.

5

FCC REGULATIONS

FCC Part 68

The FCC requires that you connectyour cordless telephone to thenationwide telephone network througha modular telephone jack (USOCRJ11C, RJ11W or RJ14).

Your telephone company maydiscontinue your service if yourequipment causes harm to the telephonenetwork. They will notify you in advanceof disconnection, if possible. Duringnotification, you will be informed of yourright to file a complaint with the FCC.

Occasionally, your telephonecompany may make changes in itsfacilities, equipment, operation, orprocedures that could affect theoperation of your equipment. If so, youwill be given advance notice of thechange to give you an opportunity tomaintain uninterrupted service.

The Base Unit contains no userserviceable parts. The Handset containsa user replaceable battery pack.

If it is determined that your telephoneequipment is malfunctioning, the FCCrequires that it not be used and that it beunplugged from the modular jack untilthe problem has been corrected.Repairs to this telephone equipment canonly be made by the manufacturer or itsauthorized agents or by others whomay be authorized by the FCC. Forrepair procedures, follow the instructionsoutlined under the Limited Warranty.

This equipment may not be used oncoin service provided by the phonecompany or Party Lines.

The REN is useful in determining thenumber of devices you may connect toyour telephone line and still enable thedevices to ring when you receive a call.The general rule is that the REN valueshould not exceed 5.0 total; however,contact your local telephone companyfor the specific number in your area.

6

When using your telephoneequipment, basic safety precautionsshould always be followed to reduce therisk of fire, electric shock and injury topersons, including the following:

1.Read and understand all instructions.

2.Follow all warnings and instructionsmarked on the product.

3. Unplug this product from the walloutlet before cleaning. Do not useliquid cleaners or aerosol cleaners.Use a damp cloth for cleaning.

4.Do not use this product near water(for example, near a bath tub, kitchensink, or swimming pool).

5. Do not place this product on anunstable cart, stand, or table. Theproduct may fall, causing seriousdamage to the product.

6.Slots and openings in the cabinet onthe back or bottom are provided forventilation.To protect it fromoverheating, these openings mustnot be blocked by placing the producton a bed, sofa, rug, or other similarsurface. This product should neverbe placed near or over a radiator orheat register. This product should notbe placed in a built-in installationwhere proper ventilation is notprovided.

7.This product should be operated onlyfrom the type of power sourceindicated on the marking label. If youare not sure of the type of powersupply to your home, consult yourdealer or local power company.

IMPORTANT SAFETY INSTRUCTIONS

8.Do not allow anything to rest on thepower cord. Do not locate thisproduct where the cord will beabused by persons walking on it.

9.Never push objects of any kind intothis product through cabinet slots asthey may touch dangerous voltagepoints or short out parts that couldresult in a risk of fire or electric shock.Never spill liquid of any kind on theproduct.

10.To reduce the risk of electric shock,do not disassemble this product, buttake it to an authorized servicefacility. Opening or removing cabinetparts other than specified accessdoors may expose you to dangerousvoltage or other risks. Incorrectreassembling can cause electricshock when the appliance issubsequently used.

11.Do not overload wall outlets andextension cords as this can result inthe risk of fire or electric shock.

12. Unplug this product from the walloutlet and refer servicing to anauthorized service facility under thefollowing conditions:

A. When the power supply cord or plugis damaged or frayed.

B. If liquid has been spilled into theproduct.

C.If the product has been exposed torain or water.

7

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

D.If the product does not operatenormally by following the operatinginstructions. Adjust only thosecontrols that are covered by theoperating instructions, becauseimproper adjustment of other controlsmay result in damage and will oftenrequire extensive work by anauthorized technician to restore theproduct to normal operation.

E. If the product has been dropped andthe cabinet has been damaged.

F. If the product exhibits a distinctchange in performance.

13.Avoid using a telephone (other thana cordless type) during an electricalstorm. There may be a remote riskof electric shock from lighting.

14.Do not use the telephone to reporta gas leak in the vicinity of the leak.

CTIONS

8

The Handset of your QW1734 ispowered by a rechargeable battery pack.It charges automatically whenever theHandset is in the Base Unit. You shouldcharge the battery pack for 16 hourswhen you first receive your phone. You’llknow the battery pack needs chargingwhen:

• The low battery message is displayed:

• The Handset seems completely dead,the LCD is completely clear and doesnot activate when you press thekeys.

TO CHARGE THE BATTERYPACK

To charge the battery pack, place theHandset in the Base Unit. TheCHARGING indicator will light to showthe Handset is seated properly and thebattery pack is charging. It isrecommended that the battery pack becharged for at least 16 hours initially.Afterwards, 8 hours of maintenancecharging should be sufficient. You canuse your telephone before that withdiminished capacity, but it is best tocharge the battery pack fully. It will takeseveral recharge cycles to maximizethe charge capacity of your battery pack.The maximum battery life betweencharges is 7 hours of continuous talktime or 14 days of stand by.

INSTALLING THE BATTERY PACK

Alternatively, if a spare battery packhas been charging in the Base Unit,simply exchange the drained Handsetbattery pack with the fully chargedreplacement battery pack from the BaseUnit charger. Place the drained Handsetbattery pack into the Base Unit chargerso that it will charge.

The Base Unit spare battery chargerdoes NOT charge a battery pack asquickly as the main Handset batterycharger. A full charge requires 24 hours.

A WORD ABOUTRECHARGEABLE BATTERIES

Your Ni-Cd battery pack rechargeswhenever the Handset is returned to theBase Unit.

IT’S IMPOSSIBLE TOOVERCHARGE THE BATTERYPACK

The battery pack can be rechargedmany times but if you get a low-batterysignal even after 8 hours of charging inthe Base Unit cradle (or 24 hours in theBase Unit spare battery charger), thebattery pack(s) should be replaced.

Replacement batteries can bepurchased from many retail storesthat carry electronic equipment.

9

INSTALLING THE BATTERY PACK

REPLACING THE HANDSETBATTERY PACK

Follow the steps below:1.Remove the battery case cover by

pressing on the ridged lines andsliding downward.

2.Discard the old battery pack. Don’tput the old battery pack in a trashcompactor or a fire - it could burst.Please recycle.

3.Place the new battery pack in itshousing with the metal contactsfacing down.

4.Replace the battery case cover bysliding the cover upwards.

5.If the new battery pack is not alreadycharged, place the Handset in thecradle of the Base Unit to allow it tocharge for 16 hours.

CAUTION: To Reduce the Risk ofFire or Injury, Read and Follow theInstructions

1.Use only the supplied rechargeablebattery pack, or equivalent.

2.Do not dispose of the battery packin a fire. The cell may explode.

IMPORTANT: Do not dispose of thisbattery pack into household garbage.For information on recycling or properdisposal, consult your local solidwaste collection or disposalorganization.

3.Do not open or mutilate the batterypack. Released electrolyte iscorrosive and may cause damage tothe eyes or skin. It may be toxic ifswallowed.

4.Exercise care in handling batteries inorder not to short the battery withconducting materials such as rings,bracelets, and keys. The batterypack or conductor may overheat andcause burns.

Replacement batteries can bepurchased from many retail storesthat carry electronic equipment.

SPARE BATTERY CHARGER/POWER BACKUP FUNCTION

When an optional, Spare Battery packis installed in the Base Unit, the QW1734uses this battery to provide operationalbackup in case of a power failure. If youhave a fully charged battery pack in theSpare Battery charger and there is apower outage, you will still be able toplace and receive calls on the QW1734Handset for up to 4 hours.

The Spare Battery pack can also beused to replace a drained Handsetbattery to ensure uninterrupted use. Besure to put the drained battery pack inthe Spare Battery charger.

1 0

GETTING STARTED

SETTING UP AC POWERADAPTERPlug the AC power adaptor into an

electrical outlet and the DC connectorto the back of the Base Unit.

CAUTION: USE CLASS 2, 9VDC POWER SUPPLY ONLY.

SETTING RINGERThe Handset ringer is programmed

ON as the factory default setting. Tochange ringer settings, see RINGERTONE / VOLUME.

The Base Unit ringer is controlledindependently, by a switch located onthe front, right hand side (antenna side)of the Base.

The Base ringer has 3 settings; high,low and off.

TONE/PULSE SELECTIONYour QW1734 is preset for Tone

dialing. If you have rotary (pulse)service, program the Handsetaccordingly. See SET TONE/PULSEfor details.

CHARGE THE HANDSETBATTERY PACK BEFORE USE.The battery pack recharges

automatically whenever the Handset isin the Base Unit. The battery pack mustbe charged for 16 hours before usingyour phone for the first time.

CONNECT THE TELEPHONELINE CORDPlug one end of the telephone line

cord into the jack on the back of theBase Unit, plug the other end of this cordinto the wall jack.

CHECK FOR A DIAL TONEAfter the battery is charged, rotate the

Base Unit antenna to upright position.Now press PHONE on the Handset.PHONE ON will appear on the LCD,and you will hear a dial tone. If not, seeIN CASE OF DIFFICULTY.

Fill in the telephone number card onthe Base Unit.

CAUTION:1. Never install telephone wiring during

a lightning storm.

2. Never install telephone jacks in wetlocations unless the jack isspecifically designed for wetlocations.

3. Never touch uninsulated telephonewires or terminals unless thetelephone line has been disconnectedat the network interface.

4. Use caution when installing ormodifying telephone lines.

1 1

USING THE WALL MOUNTADAPTOR

1. Position the wall mount bracketon the Base Unit.Line up the tabs on the wall mountadaptor with the holes on the bottomof the Base Unit . Snap the wallmount bracket firmly in place.

2. Mount the Base Unit on the wall.Position the Base Unit so themounting studs will fit into the holeson the bottom of the Base Unit.Position the power cord to extenddown the wall the phone is to bemounted on. Slide the Base Unitdown on the mounting studs until itlocks into place.

3. Plug in the AC adaptor.Plug the AC adaptor into an electricaloutlet, and the DC connector to theback of the Base Unit. If the Handsetbattery pack has not been chargedpreviously, place the Handset inthe Base Unit cradle, and allow itto charge for 16 hours.

WALL MOUNTING

4. Connect the telephone line cord.The telephone line cord has asnap-in plug at each end. Insert oneof the plugs into the jack on thebottom of the Base Unit. Insert theother end of the plug into the walljack.

1 2

HANDSET LAYOUT

1 3

BASE LAYOUT

1 4

QUICK REFERENCE GUIDE

Here is a brief guide to the featuresand functions of your QW1734 cordlesstelephone:

SET-UP

• Plug AC adaptor into a standardelectrical outlet.

• Let Handset battery pack charge for16 hours before first use.

• Set Dial Mode setting in MENU toPULSE or TONE. The unit is factoryset to TONE.

• Connect telephone line cord to BaseUnit and telephone jack.

SETTING TIME

With the Handset in the idle (off) mode:• Press MENU

• Use the / soft keys to scrolluntil 5. Set Time is highlighted

• Press ENTER

• Enter the current hour. A single-digithour must be preceded by a 0.

• Next, enter the minute.

• Next, select the Hour Presentation(12-hour or 24-hour format) bypressing the key directly below the12 or 24 icon in the handset display.

• Press SAVE. The display will confirmthat the time has been updated.

• The time setting will alsoautomatically be updated when Time/Date information is received fromCaller ID.

MAKING CALLS

FROM THE HANDSET

• Press PHONE. The Handset willbriefly display CONNECTING, thenPHONE ON. Listen for dial tone.Using the keypad, dial the desirednumber. To end your call, pressOFF, or return the handset to thebase unit.

-OR-

• First, dial the desired number. Then,press PHONE. After accessing dialtone, the phone number will bedialed. To end your call, press OFF,or return the handset to the baseunit.

1 5

When you end your call by pressingOFF or returning the handset to thebase unit, the phone will return tothe rotary (PULSE) mode.

VOLUME CONTROL

FROM THE HANDSET

• The phone must be ON.

• Located on the side of the Handset,press the VOLUME UP or VOLUMEDOWN keys to raise or lower theearpiece volume. There are 8volume levels.

FROM THE BASE• The Base Unit has its own volume

control. The VOL Up and Downkeys are located directly above theSPEAKERPHONE key.

RINGER CONTROL

FROM THE HANDSETWith the Handset in the idle (off) mode:

• Press MENU

• Using the / soft keys, scrolluntil 3. Ringer Tone/Vol ishighlighted.

FROM THE BASE• Press SPEAKERPHONE, then wait

for dial tone. Dial the desired phonenumber.

• To end your call, pressSPEAKERPHONE again.

ANSWERING CALLS

• When there is an incoming phonecall, pressing OFF key on thehandset can stop the ringing.You canalso answer the call simply bypressing any key except OFF,VOLUME, INTERCOM and the 3Services keys.

FROM THE HANDSET:• Press any key except OFF, Volume,

INTERCOM and the 3 Services keys.

• Press OFF to end your call.

FROM THE BASE:• Press SPEAKERPHONE. To end

your call, press SPEAKERPHONEagain.

TEMPORARY TONE

• If your local telephone servicerequires rotary (PULSE) dialing,you can temporarily switch to TONEdialing for such purposes asaccessing answering machines,bank-by-phone services, and usingcalling cards.

• To switch from rotary to tone dialing

during a call, press the *TONE key.


1 6

• Press ENTER• Use the RING soft key to select the

Ringer Type (there are 4 ring styles)and Vol soft key to select the ringervolume (High, Low or Off).

• Press SAVE to store your ringersettings

• To exit programming mode at anytime, press OFF key .

FROM THE BASE• The Base Unit ringer is controlled

independently, by a switch locatedon the front, right hand side (antennaside) of the Base.

• The Base ringer has (3) settings:High, Low and Off.

HOLD

FROM THE HANDSET

• Press the HOLD soft key to placean active call on hold. Press theTALK soft key or the PHONE keyto return to your call.

• If an extension phone is activatedwhile the QW1734 has a call onHOLD, the QW1734 will release thecall and turn itself OFF.

FROM THE BASE

• During a Speakerphone call, pressHOLD on the Base Unit. The redlight (LED) buit into theSPEAKERPHONE key, will flash

rapidly while your call is on hold.

• Press either HOLD orSPEAKERPHONE to return toyour call.

MUTE

FROM THE HANDSET• Press the MUTE soft key to disable

the Handset microphone during anactive call. Press the TALK softkey to return to normal 2-wayconversation.

FROM THE BASE• During a Speakerphone call, press

MUTE to disable the Base Unitmicrophone. The red light (LED) buitinto the MUTE key, will glow.

• Press MUTE again to return to atwo-way conversation.

REDIAL WITH THE HANDSETON

• Press the RDL soft key to displaythe last three telephone numbersyou dialed.


1 7

• Using the / soft keys, selectthe number from the list and thenpress DIAL soft key.

REDIAL WITH THE HANDSETOFF

• Press RDL. The Handset will displaylast 3 phone numbers dialed.

• Use the / soft keys tohighlight the desired phone number.

• Press PHONE. The QW1734 willaccess dial tone, and dial thenumber.

PAGE/HANDSET LOCATOR

• To page the Handset from the BaseUnit, press INTERCOM. TheHandset will emit a special beeptone for up to 60 seconds, Inaddition, the Handset will displayBASE PAGING.

• To answer the page, pressINTERCOM on the Handset. Youare now in intercom mode.

• To terminate the page, press OFFon the Handset,or INTERCOM onthe Base Unit.

INTERCOM BETWEENHANDSET AND BASE

FROM THE HANDSET (WHENHANDSET IS OFF)

• Press the INTERCOM key. TheBase Unit will emit 2 short tonesand then enter Intercom mode. Youcan now talk to the person at theBase Unit.

• The Handset will display as:


1 8

• Press the MUTE softkey to mute thehandset microphone.

• You can return to the intercomconversation with the Base bypressing the TALK softkey.

• Press the OFF key to end theintercom mode.

FROM THE HANDSET (WHENHANDSET IS ON)

• You can use the intercom when youare on a call.

• Press the INTERCOM key, then youcan talk to the Base unit.

• At the same time, your active call willbe placed on HOLD.

• You can press the MUTE softkey tomute the handset microphone.

• You can return to the intercomconversation with the Base bypressing the TALK softkey.

• Press the OFF key to end theintercom mode. But, at this time, yourcall is still on hold. You need to pressthe TALK softkey or the PHONEkey to return to your call.

• Anytime in the intercom mode, youcan press the PHONE key to endthe intercom and return to your call.


FROM THE BASE (WHENSPEAKERPHONE IS OFF)

• Press INTERCOM key to page theHandset.

• After the Handset receives the pagefrom the Base, press the INTERCOMkey on the Handset to establishconversatiion.

• During the intercom, you can pressthe MUTE key to mute themicrophone on the Base.

• Press the MUTE key once again torelease the mute function.

• Press INTERCOM key to exit theintercom mode.

FROM THE BASE (WHENSPEAKERPHONE IS ON)

• You can use intercom during a call• Press INTERCOM key to page the

Handset. You will be on hold.• After the Handset receives the page

from the Base, press the INTERCOMkey on the Handset to establishconversation.

• During the intercom, you can pressthe MUTE key to mute themicrophone on the Base.

• Press the MUTE key once again torelease the mute function.

• Press INTERCOM and thenSPEAKERPHONE key to exit theintercom mode and return to the call.

• Or simply press SPEAKERPHONEto exit the intercom mode and returnto the call.

1 9


CONFERENCE

Your QW1734 allows you to establisha 3 party conference between theHandset, Base and the incoming call:1) Use either the Base or the Handset

to make a call.2) If you are using the Base to make

the call, the Handset can join theconference by pressing PHONE.Or, press the SPEAKERPHONEkey on the Base if you use theHandset to make the call.

3) If either the Handset or the Baseparties want to leave the conference,either side can press OFF (on theHandset) or SPEAKERPHONE(onthe Base) to leave.

REVIEWING CALLER IDRECORDS

NOTE: Caller ID and Call Waiting IDare subscription services, availablethrough most local telephone serviceproviders. These are optional services;you are not required to subscribe tothem. However, to receive Caller ID onyour QW1734, subscription through yourlocal phone company is required.

When the Handset is not on a call:• Press MENU

• Using the / soft keys scrolluntil 1. Caller ID is highlighted

• Press the ENTER soft key.

• Use the / soft keys to scrollthrough the Caller ID records. TheQW1734 will store the last 50 CallerID records to come in.The latestone will be in #01.

• Press OFF to exit Caller ID mode.

MEMORY DIALING

FROM THE HANDSETWhen the Handset is not on a call:

• Press the MEM soft key.

• Enter Memory Location (01-25).Assoon as you enter the second digit,the contents of the selected MemoryLocation will be displayed.

• Press PHONE key or the DIAL softkey to dial the displayed phonenumber.

2 0


When the Handset is on a call:

• Press PHONE. Listen for dial tone.

• Press the MEM soft key.

• Enter Memory Location (01-25).

• Press the PHONE or DIAL key.

FROM THE BASE• Press SPEAKERPHONE to get

the dial tone.• Press MEMORY key, then enter 2

digit location number (01-25).

• You will then hear the dialingsequence.

FLASH

• You can use your QW1734 withservices such as Call Waiting.Simply press the PHONE key toflash the line on the Handset, ORpress FLASH on the Base.

HANDSET SPEAKERPHONEFEATURE

Press the SPEAKER to make oranswer a call using the HandsetSpeakerphone. The Handset displaysHS SPEAKER. You can now talkhands-free away from the Base Unit.Press OFF to end a call.

Call Waiting: If you hear a Call Waitingtone during a speakerphone call,press the SPEAKER key to answerit. (Do not use the PHONE key toanswer Call Waiting while using thespeakerphone.)

Switching from Speakerphone toEarpiece: At any time during aHandset speaker call, you canpress PHONE to switch to anon-speaker call. The Handset willdisplay PHONE ON, and you canhold the handset to your ear normally.Press Speaker whenever you wantto change back to theSpeakerphone. The Handset willdisplay HS SPEAKER.

2 1

SOFT MENU FUNCTIONS

The QW1734 has an advanced designwhich uses a menu system and softkeys to access all of the built in features.

Example of the idle mode display:

NEW: The number of Caller ID recordsnot previously viewed

TOTAL: The total number of storedCaller ID records (50 max.)

RDL (Redial)Press RDL to display the last 3

telephone numbers dialed. The numberon the top line is the most recent numberdialed. The display will look like:

• Use the / soft keys to selectdesired number.

• Once highlighted, press PHONE todial.

• To save the phone number in thephone book directory, press SAVE.The LCD will display:

• Press PSE if you want to add a 2second pause in the dialing sequence.

• Press CLR to backspace

• Press SAVE to save the phonenumber in the Phone Book directory.The LCD will display:

• Using the keypad, enter the desiredname (15 character maximum)

• Press to advance the cursor to thenext space. You won’t have toadvance the cursor if the next letterof the name is not on the same keyas the previous letter; it will advanceautomatically.

• Press CLR to backspace

• Press SAVE when you finishedentering the desired name. The LCDwill display:

• The 2-digit location displayed is thesmallest, unoccupied directorylocation. If you want to save thephone number in a different location,press CLR, and then enter the twodigit directory location you desire(01-25).

• Press SAVE to confirm your locationselection. The screen will display:

2 2

SOFT MENU FUNCTIONS

Then the display shows:

You can record your voice saying theperson's name. If you subscribe to CallerID, the phone will play your recordingwhen this person calls, so that you canhear who's calling without seeing theCaller ID display.

If you do not want to record a name:• Press NO.To record a name:• Press YES and speak after the beep.

• You can press # when you're finishedspeaking, OR just wait-recording endsafter 4 seconds.

The Handset shows:

To hear your recording:• Press ENTER while1. Play Back VA

is highlighted.To make a new recording of the name:

• Press until 2. Redo VA ishighlighted.

• Press ENTER and speak after thebeep.You can re-record as many times as

you want. Each time you re-record orreview the name, the Handset shows:

When you are satisfied with yourrecording:• Press EXIT.

MEM (Memory)

From the idle mode display,pressMEM, the screen will now display:

Enter the 2-digit location coderepresenting the Phone Book directoryrecord you wish to access. The screenwill display the contents of that record. Ifthe contents of the selected record areempty, the screen will display:

and then ask for another 2-digit locationcode.

With the contents of the Phone Bookrecord displayed, press:

• DIAL to access the line and dial thedisplayed phone number,

• CLR to clear the display and allowyou to enter another location number,

• EXIT to exit Memory Dialing, andreturn to the idle mode display.

2 3

SOFT MENU FUNCTIONS

You can also access directory recordsby entering the name of the desiredparty. See PHONE BOOK for details.

MENU

With the Handset in the idle (OFF)mode, press the MENU key to accessthe following options:1. Caller ID2. Phone Book3. Ringer Tone/Vol4. KeyBeep On/Off5. Set Time6. Clear ALL MEM7. AutoAns (Auto Answer) On/Off8. Set Tone/Pulse9. Del (Delete) MSG Icon*. Voice Announce

Use the / keys to select thedesired option, then press ENTER.

Because there are only three lines todisplay information, only three of themenu options will be displayed at a time.The first screen displayed is:1. Caller ID2. Phone Book3. Ringer Tone/Vol

The second screen is:4. KeyBeep On/Off5. Set Time6. Clear ALL MEM

The third screen is:7. AutoAns (Auto Answer) On/Off8. Set Tone/Pulse9. Del (delete) MSG IconAnd the fourth screen is:*. Voice Announce

The following sections detail how toaccess and operate the ten MENUfunctions.

Note: You do not have to use the

/ soft keys to select menuoptions. Instead, you can simply pressthe number key that corresponds tothe desired feature.

For an example, if you want to access the

Set Time function, using the / softkeys you would do the following:• Press MENU

• Using the / keys, scroll until5. Set Time is highlighted

• Press ENTER

• Then follow the on-screen promptsHowever, using the shortcut, all you

would need to do is:• Press MENU• Press the 5 key to enter the Set

Time function

• Then follow the on-screen prompts.

2 4

CALLER ID

Once you have chosen CALLER ID(Menu selection #1), the screen willdisplay:

• If an N in a shaded box appears in theupper right hand corner of the CallerID screen, this indicates that it is anew(not previously viewed) record.If a number in a shaded box appearsin the upper right hand corner of theCaller ID screen, this indicates thatyou have received multiple calls fromthis party. For example, a 3 indicatesthat the party has called 3 additionaltimes since the initial call. This repeatindicator can go to a maximum of 9.

• Use the / keys to scroll throughthe records.

• Once you have found the desiredrecord, press PICK.

You now have 3 options:• SAVE the phone number (and name)

in the Phone Book directory,• DIAL the phone number, or• DEL (delete) the Caller ID record from

memory.

SAVEPress SAVE while reviewing a Caller ID

record. The screen will display:

• Press PSE if you want to add a 2second pause in the dialing sequence

• Press CLR to backspace• Press SAVE to save the phone

number in the Phone Book directory.The LCD will display:

• Press to advance the cursor to thenext space. You won’t have to advancethe cursor if the next letter of thename is not on the same key as theprevious letter; it will advanceautomatically.

• Press CLR to backspace• Press SAVE when you finish entering

the desired name.The LCD will display:

• If you want to save the phone numberin a different location, press CLR,and then enter the two-digit directorylocation you desire (01-25).

• Press SAVE.The screen will confirmyour location selection.Then the display shows:

You can record your voice saying theperson's name. If you subscribe to CallerID, the phone will play your recordingwhen this person calls, so that you canhear who's calling without seeing theCaller ID display.

2 5

If you do not want to record a name:• Press NO.

To record a name:• Press YES and speak after the beep.• You can press # when you're finished

speaking, OR just wait-recording endsafter 4 seconds.The Handset shows:

To hear your recording:• Press ENTER while 1. Play Back VA is

highlighted.To make a new recording of the name:

• Press until 2. Redo VA ishighlighted.



When you are satisfied with yourrecording:• Press EXIT.

NOTE: To cancel the operation,press EXIT to return to the idle modedisplay at any time. The screen willdisplay:

DIALPress DIAL or PHONE when reviewing

a Caller ID record. The screen will displayup to 4 dialing options: (examples)

1. 555-1212Local# only (7 digits)

2. 1-503-555-1212Long Distance (11 digits)

3. 503-555-1212Area Code+ local# (10 digits)

4. 1-555-1212“Local” Long distance (8 digits)

• To dial, use the / scroll keysto select the desired dialing option,then press DIAL or PHONE;

- OR -

• Enter the desired number key, 1through 4. The QW1734 will accessdial tone, and dial the selectedsequence.

DEL (Delete)Press DEL while reviewing a Caller

ID record. The screen will display:

CALLER ID

• Press YES to delete the displayedCaller ID record. The screen will say:

• Press NO to cancel the deletion, andreturn to the main display.

CALLER ID - CALL WAITINGIDYour QW1734 is capable of displaying

the name and/or number of the partycalling before you answer the phone(Caller ID). It is also capable of displayingCaller ID information in conjunction with aCall Waiting alert signal (Call WaitingID). With Call Waiting ID, the Caller IDdata will help you decide whether to switchto the incoming call, or continue with yourcurrent conversation.

NOTES ABOUT CALLER ID& CALL WAITING IDThese are subscription services,

provided by most regional telephoneservice providers. You must subscribe tothese services to get the benefits of thesefeatures. If you do not subscribe to CallerID services, you can still use yourQW1734 and the other features it offers.

Due to regional incompatibilities, CallerID information may not be available forevery call you receive. In addition, thecalling party may block their name andphone number from being sent.

VOICE ANNOUNCE CALLERIDIf you subscribe to Caller ID, the unit

can be programmed to announce thecaller's name or number from the Base

CALLER ID

Unit speaker, while displaying the CallerID information on the Handset.

If you want the phone to announcenames, you must record a name with thenumbers in your Phone Book. See thesection" PHONE BOOK: ADDING NEWPHONE BOOK RECORDS AND VOICEANNOUNCE RECORDS".

NOTE: Phonebook entries must includethe AREA CODE in order for caller'sname to be announced.

If an inbound call has the Caller IDinformation blocked, the Base Unit willannounce " PRIVATE CALLER".

If the Caller ID information unavailable(both name and number), the Base Unitwill announce " UNKNOWN CALLER".

You can choose to turn off VoiceAnnounce, or to announce only yourpre-recorded names. The Handset willstill display all Caller ID information.

To turn Voice Announce ON or OFF:• Press MENU.

• Using the / keys, scroll until *.Voice Announce is highlighted.

• Press ENTER, you will see one of threeannouncement options:

ON: Announce names that you haverecorded, and phone numbers for allother callers. This is the factory default.

NAMES ONLY: Announce names thatyou have recorded. If you have notrecorded a caller's name, you will nothear anything.

OFF: Nothing is announced aloud.• Press ANN until the desired option is

displayed.• Press SAVE, the Handset will beep.

2 6

PHONE BOOK

The names and phone numbers of 25frequently called parties can be stored inthe QW1734 Phone Book directory. Youwill find instructions for programmingnames and numbers into the directory inthe section, ADDING NEW PHONEBOOK RECORDS.

Once you have chosen PHONE BOOK(Menu selection #2), the screen willdisplay:

Using the numeric keys, enter the firstletter of the desired name. The Handsetwill display either the exact record, or aclose match. If it is not the desired

record, press the / scroll keys tosearch.

If the phone book record is savedwith Voice Announce Recording, anicon will be displayed at the topright corner.

Once you are viewing the desiredrecord, press PICK. You now have thefollowing options:• EDIT – if you want to change the

name or phone number• DIAL – to access the line and dial the

phone number• DEL - to delete the record from the

directory. You will then be promptedto press YES to confirm deletion orNO to cancel and return to the idlemode display.

EDITING PHONE BOOKRECORDS & VOICEANNOUNCE RECORDSIf you press EDIT, the Handset will

display:

• Press PSE if you want to add a2-second pause in the dialing sequence



• Press to advance the cursor to thenext space. You won’t have toadvance the cursor if the next letterof the name is not on the same keyas the previous letter; it will advanceautomatically.

• Press CLR to backspace• Press SAVE when you finish entering

the desired name. The LCD willdisplay:

The 2-digit location displayed is itsoriginal location.

If you want to save the phone numberin a different location, press CLR, andthen enter the two-digit location number.

Press SAVE to confirm your locationselection. The screen will display:

2 7

PHONE BOOK

2 8

If you are saving an edited record in itsoriginal directory location, you will seethe following message after pressingSAVE:

If you press NO, the Handset will returnto:

You can choose a new location, orpress EXIT to return to the idle modedisplay.

If you press YES, the Handset willdisplay:

If the phone book record has a VoiceAnnounce Recording, after you havesaved the edited record, the LCD willdisplay :

You can playback, redo or erase therecording by selecting from the abovemenu. For detail operation, please seepage 29.

For a phone book record without aVoice Announce Recording, the Handsetwill prompt you:

Press YES if you want to record a nameor NO if you do not.

ADDING NEW PHONE BOOKRECORDS & VOICEANNOUNCE RECORDSStarting from the idle mode (off) display,

enter the number you want to store in thePhone Book directory. Then:• To save the phone number in the

phone book directory, press SAVE.The LCD will display:

• Press PSE if you want to add a 2-secondpause in the dialing sequence



Each of the number keys has a specificset of characters. Each press of aparticular number key causes charactersto be displayed in the following order:

PHONE BOOK

2 9

Number Key Characters (in order)1 ..................... & ' , . 12 ..................... A B C 23 ..................... D E F 34 ..................... G H I 45 ..................... J K L 56 ..................... M N O 67 ..................... P Q R S 78 ..................... T U V 89 ..................... W X Y Z 90 ..................... 0

• Press to advance the cursor to thenext space.You won’t have to advancethe cursor if the next letter of thename is not on the same key as theprevious letter;it will advanceautomatically.

• Press CLR to backspace• Press SAVE when you're finished

entering the desired name. The LCDwill display:

• The 2-digit location displayed is thesmallest, unoccupied directorylocation. If you want to save thephone number in a different location,press CLR, and then enter the twodigit directory location you desire(01-25).

• Press SAVE to confirm your locationselection.The screen will display:

Then the display shows:

In your own Voice you can record theperson's name associated with this record.If you subscribe to Caller ID, the phonewill play your recording when this personcalls, so that you can hear who's callingwithout seeing the Caller ID display.

If you do not want to record a name:• Press NO.

To record a name:• Press YES and speak after the beep.• You can press # when you're finished

speaking, OR just wait-recording endsafter 4 seconds.The Handset shows:

To hear your recording:• Press ENTER while 1. Play Back VA is

highlighted.To make a new recording of the name:

• Press until 2.Redo VA ishighlighted.



When you are satisfied with yourrecording:• Press EXIT.To erase the recording,• Press ENTER while 3. Erase VA is

highlighted.• A confirmation tone will be heard.• Press EXIT when you're finished. You

will see the is removed on the PhoneBook record.

OTHER MENU SETTINGS

RINGER TONE / VOLUME

You can adjust the Handset ringerstyle and volume level. There are 4ringer styles and 3 volume levels: HI,LO, and OFF.

Once you have selected RINGERTONE/VOL (Menu selection #3), theHandset will display:

To select a ringer style, press theRING soft key.

To adjust ringer volume, press theVOL soft key.

Press SAVE to confirm yourselections. The screen will displaySetting Updated, and return to the idlemode display.

If you select Ringer Volume HI , theidle mode screen will display'' ''.

If you select Ringer Volume LO, theidle mode screen will display'' ''.

If you select Ringer Volume OFF,the idle mode screen will display '' ''.

KEY BEEP ON/OFF

As you use your QW1734, you willhear a quiet beep with each key press.You can turn this feature off, if you chooseKEY BEEP to be OFF.

Once you have selected KEY BEEPON/OFF (Menu selection #4), theHandset will display:

Press ON or OFF, depending on yourpreference, then press SAVE. Thescreen will display Setting Updated,and return to the idle mode display.

Factory default setting is Key BeepON.

3 0

SET TIME

Once you have selected SET TIME(Menu selection #5), the Handset willdisplay:

For detail operation, please see" SettingTime" on Page 14.

After pressing SAVE to confirm yourselections, the Handset will displaySetting Updated, and return to the idlemode display.

CLEAR ALL MEM

This feature allows you to erase theentire contents of the PHONE BOOKand/or CALLER ID memory.

Once you have chosen CLEAR ALLMEM, (Menu selection #6), the Handsetwill display:

Use the / scroll keys to makeyour selection, then press ENTER.

The screen will ask you to confirmyour decision to delete the entire contentsof Caller ID or Phone Book memory; forexample:

3 1

OTHER MENU SETTINGS

Press YES to confirm. The screenwill display:

If you change your mind and do notwant to delete all records, press NO.You will be returned to the idle modedisplay.

AUTO ANSWER ON/OFF

Factory default setting is AutoAnswer OFF.

With Auto Answer set to OFF,when the phone is on cradle, youcannot simply pick up the phone toanswer incoming call, you must pressPHONE to answer the call. This allowsyou to review the Caller ID informationbefore answering. However, if youprefer to have your Handsetautomatically answer the call whenremoved from the Base cradle:

Select AutoAns On/Off (Menuselection #7). The Handset will display:

Press ON (or OFF if you’re cancelingAuto Answer), then SAVE. The screenwill display Setting Updated, and returnto the idle mode display.

SET TONE /PULSE

Your QW1734 is preset for tonedialing.To change the dialing modesetting, choose SET TONE/PULSE(Menu selection #8), the screen willdisplay:

Press TONE or PULSE, dependingon the requirements of your localtelephone provider.If you are not sure,contact your local phone company.

Press SAVE. The screen will confirmthat the dialing mode is updated, andthen return to the idle mode display.

DELETE MSG ICON

Refer to MESSAGE WAITINGINDICATOR on page 34 for anexplanation of this feature.

3 2

OTHER MENU SETTINGS

HEADSET OPERATION

Your QW1734 is equipped with a2.5mm Headset Jack for use with anoptional accessory Headset for handsfree operation.

If you choose to use the Headsetoption, you must obtain an optionalaccessory Headset, which is compatiblewith the QW1734.

To purchase a Headset, call800-244-1111.

Once you have a compatible 2.5mmHeadset, locate the Headset Jack onthe QW1734 Handset. Connect theplug on the Headset cord to the jack onthe cordless Handset. The plug shouldfit securely. Do not force the connection.

OPERATION

NOTE: Whenever a compatibleHeadset is connected to the cordlessHandset, the microphone on the Handsetwill be muted. This is done to limit theeffect of background noise.

The following operationalcharacteristics apply to compatibleHeadsets. The same may also apply toother headsets, but QWEST assumesno responsibility for their performance.

BELT CLIP

The QW1734 is also equipped with adetachable belt clip. Align the pins onthe inside edge of the clip with the notcheson the sides of the QW1734 Handset.The belt clip should snap securely intoplace. Do not force the connection.

3 3

ADDITIONAL OPERATING TIPS

OUT OF RANGE INDICATION

When the handset is in Phone Onmode and moved to a point where it andthe Base Unit can no longercommunicate, the Handset will beeptwice and display OUT OF RANGE:

and attempt to re-link with the Base. Ifthis occurs while you’re on a call, movecloser to the Base Unit.

If the Handset does not re-establishcontact with the Base within 30 secondsof losing contact, the Handset willautomatically drop the call and turn off.

If you walk out of range while theHandset is not in use, the Handset willbeep twice and display OUT OFRANGE until the user presses any key.

NOTE: If the Base Unit is withoutpower, the Handset will behave as if itis out of range. Therefore, if thehandset beeps, the display OUT OFRANGE occurs, and moving closer tothe Base does not help, check theBase Unit to make sure it has power.

MESSAGE WAITINGINDICATOR (for use withVoicemail)

Your QW1734 is capable of detectinga visual Message Waiting signal,generated by many phone service

providers. If you subscribe to Voicemailservice from your local telephonecompany, and a visual message waitingsignal is provided, the QW1734 willdisplay on the right side of theHandset LCD to alert you to new,unplayed messages.

On the Base, the red MESSAGE LEDwill light up to alert you to new unplayedmessages.

Once you have reviewed all of yournew voicemail messages and hang upthe phone, the QW1734 will turn off theHandset and Base indicatorsautomatically. Note that there is a delayfor the indicators to turn off, as theQW1734 is waiting for an update signalfrom the telephone network.

After all new voicemail messages havebeen reviewed, if the MESSAGEWAITING indicator (icon or Base LED)remains on, you can manually clear theindications as follows:

• Press MENU, scroll to 9. Del MSGIcon. Press ENTER

• Press YES to turn off the Handseticon and Base LED.

3 4


NOTE: Message Waiting indicatorworks in conjunction with Voicemailservice from many local phonecompanies. This is an optional service:you are not required to subscribe to it.

ONE-TOUCH SERVICE KEYS

3 custom pay-per-use services areaccessible using one-touch keyslocated on the QW1734 Handset andBase Unit respectively:

On the Handset,AUTO CALL RETURN3-WAY CALLINGAUTO BUSY REDIAL

On the Base Unit,MESSAGES 3-WAY CALLINGCANCEL CALL WAITING

AUTO CALL RETURN dials the lastparty who called you, whether or notyou answered the call. A charge isadded to your phone bill each time youuse this feature.

3-WAY Calling allows you to talk with2 separate parties from a single line.The set-up procedure is as follows:

1) Call your first party; after the partyanswers,

2) Press 3-WAY Calling. Wait for dialtone.

3) Call your second party; after the callis answered.

4) Press 3-WAY Calling again.

In most areas, the 3-Way Calling serviceis available as a subscription service oras a pay-per-use service. If you do nothave the subscription service for 3-WayCalling, pay-per-use charges may apply.

AUTO BUSY REDIAL repeatedly dialsthe last number you called, over a timeinterval determined by your localcompany. This is useful in reaching aparty whose line is busy A charge isadded to your phone bill each time thisservice is used.

MESSAGES dials *98, which is thecode to access Qwest Voice Messagingfrom your home in the Qwest region. Ifyou subsc r i be t o Qwes t Vo i ceMessaging, when you see the theMessage Waiting Indicator pressMESSAGES on the Base to listent o y o u r m e s s a g e s .

C A N C E L C A L L W A I T I N G w i l ldeactivate Call Waiting before placingan important call. Press CANCEL CALLWAITING before dialing. During that call,there will be no interruption from CallWaiting. After you hang up, Call Waitingwill be reactivated for your next call.

CUSTOM FEATURES

Your QW1734 gives you easy accessto 5 popular custom features offered bymany telephone companies:

1. Return Call2. Repeat Dial3. No Call Wait4. Call FWD ON5. Call FWD OFF

To use a custom feature, do the following:

• Press PHONE. Listen for dial tone.• Press the SERV soft key.• Using the / soft keys, scroll

until the desired custom feature ishighlighted.

• Press ENTER.

3 5


NOTE: It is likely that your localtelephone company will assess chargesto use custom features. You shouldcheck with your local service providerregarding which custom services areavailable in your area and the associatedcosts for the intentional or unintentionaluse of pay-per-use services. Your localtelephone company may provide amonthly subscription to an individualservice or a package of services thatgives you unlimited usage for a smallmonthly fee.If you have pulse dialing selected onyour phone, the one-touch services andthe custom features may not be available.

LOW BATTERY INDICATION

During a Low Battery condition, theHandset LCD will display:

When this occurs, you should eitherreturn the Handset to the Base Unit forrecharging, or exchange the drainedHandset battery with a fully chargedbattery from the Spare Battery charger.

CHECK AC POWERINDICATION

A charged battery installed in the BaseUnit will allow you to make and receivecalls from the Handset in the event of apower failure, for approximately 4hours.During power back-up mode, theHandset will display:

3 6

If your QW1734 displays thismessage, and AC power is present,check the electrical outlet and the ACadapter, ensuring that it is firmlyconnected to the outlet and the BaseUnit.

MAINTENANCE

TAKING CARE OF YOURTELEPHONE.

Your cordless telephone containssophisticated electronic parts, so itmust be treated with care.

AVOID ROUGH TREATMENTPlace the Handset down gently. Savethe original packing materials to protectyour telephone if you ever need toship it.

AVOID WATERYour telephone can be damaged if it getswet. Do not use the Handset outdoorsin the rain, or handle it with wet hands.Do not install your Base Unit near a sink,bathtub or shower.

ELECTRICAL STORMSElectrical storms can sometimes causepower surges harmful to electronicequipment.For your own safety, be cautious whenusing electrical appliances duringstorms.

CLEANING YOURTELEPHONEYour telephone has a durable plastic

casing that should retain its luster formany years. Clean it only with a softcloth slightly dampened with water or amild soap. Do not use excess water orcleaning solvents of any kind.

Remember that electrical appliancescan cause serious injury if used whenyou are wet or standing in water. If yourbase unit should fall into water, DO NOTRETRIEVE IT UNTIL YOU UNPLUGTHE POWER CORD ANDTELEPHONE LINE CORDS FROMTHE WALL. Then pull the unit out bythe unplugged cords.

3 7

3 8

IN CASE OF DIFFICULTY

If you have difficulty operating yourphone, the suggestions below shouldsolve the problem. If you still have difficultyafter trying these suggestions, call theCustomer Service at 800-651-6791.

THE PHONE DOESN’T WORK ATALL.

• Make sure the Power Cord is pluggedin.

• Make sure the telephone line cord isplugged firmly into the Base Unit andthe telephone wall jack.

• Make sure the battery pack is properlycharged. If the "LOW BATTERY"message is shown, the battery packneeds charging.

NO DIAL TONE.• First check all the suggestions above.• If you still don’t hear a dial tone,

disconnect the Base Unit from thetelephone jack and connect a differentphone. If there is no dial tone on thatphone either, the problem is in yourwiring or local service. Call your localtelephone company.

YOU GET NOISE, STATIC, OR AWEAK SIGNAL EVEN WHENYOU’RE NEAR THE BASE UNIT.

• Household appliances plugged intothe same circuit as the Base Unit cansometimes cause interference. Trymoving the appliance or the BaseUnit to another outlet.

YOU GET NOISE, STATIC, OR AWEAK SIGNAL WHEN YOU’REAWAY FROM THE BASE UNIT.

• You may be out of range.Either moveclose to or relocate the Base Unit.

• The layout of your home may belimiting the range. Try moving theBase Unit to another position.

THE HANDSET DOES NOT RINGWHEN YOU RECEIVE A CALL.

• Make sure you have the Handsetringer activated.

• Make sure the telephone line cord isplugged firmly into the Base Unit andthe telephone jack. Make sure thepower cord is plugged in.

• You may be too far from the BaseUnit. And the "OUT OF RANGE"message is shown on LCD.

• You may have too many extensionphones on your telephone line toallow all of them to ring.Try unpluggingsome of the other phones.

YOU HEAR OTHER CALLS WHILEUSING YOUR PHONE.

• Disconnect your Base Unit from thetelephone jack, and plug in a regulartelephone. If you still hear other calls,the problem is probably in your wiringor local service. Call your localtelephone company.

YOU HEAR NOISE IN THEHANDSET, AND NONE OF THEKEYS OR BUTTONS WORK.

• Make sure the power cord is pluggedin.

COMMON CURE FORELECTRONIC EQUIPMENTIf the unit does not seem to be

responding normally, then try putting theHandset in the cradle. If it does notseem to respond, do the following(in theorder listed):1. Disconnest the power to the base.2. Disconnect the Handset battery, and

spare battery pack, if applicable.3. Wait a few minutes.4. Connect power to the Base.5. Re-install the battery pack(s).6. Try using your phone again.

3 9

WARRANTY STATEMENT

WHAT DOES OUR WARRANTY COVERS?• Any defect in material or workmanship.FOR HOW LONG AFTER THE ORIGINAL PURCHASE?• To the original purchaser only - ONE YEAR.WHAT WILL WE DO?• At our option, repair or replace your unit.WHO DO I SEND MY UNIT, IN OR OUT OF WARRANTY?• In the U.S. call Customer Service for Return Authorization

at: 800-651-6791.• Properly pack your unit. Include any cables & accessories which were

originally provided with the product. We recommend using the originalcarton and packing materials.

• Include in the package a copy of the sales receit or other evidence of dateof original pruchase(if the unit was purchased within the last twelvemonths).

• Print your name and address, along with a description of the defect, andinclude this in the package.

• Include payment for any service or repair not by warranty, as determinedby Qwest Customer Service.

• Ship the unit via UPS insured, or equivalent to the address provided byQwest Customer Service.

Qwest assumes no responsibility for units sentwithout prior Return Authorization.

WHAT DOES OUR WARRANTY NOT COVER?• Batteries• Damage from misuse, neglect, or acts of nature (lightning, floods, power

surges, etc.)• Products with may have been modified or incorporated into other products• Products purchased and/or operated outside the USA, its territories.• Products serviced by the owner or a service facility not expressly authorized

by Qwest Customer Service.• Products purchased more than 12 months from current date• Units purchased in "AS IS" condition, or units purchased as "Distressed

Merchandise".HOW DOES STATE LAW OR PROVINCIAL LAW RELATE TO THIS WARRANTY?• This warranty gives you specific rights. You may also have other rights

which vary from state to state.

Qwest Customer Service

4 0

TECHNICAL SPECIFICATIONS

FREQUENCY CONTROLCrystal Controlled Dual PLL Synthesizer

TRANSMIT FREQUENCYHandset :

904.20 MHz to 925.80 MHz( All 20 channels within thisrange)

Base Unit:904.20 MHz to 925.80 MHz(All 20 channels within thisrange)

RECEIVE FREQUENCYHandset :

904.20 MHz to 925.80 MHz( All 20 channels within thisrange)

Base Unit:904.20 MHz to 925.80MHz( All 20 channels within thisrange)

NOMINAL EFFECTIVERANGEMaximum power allowed by FCC and

IC. Actual operating range may varyaccording to environmental conditionsat the time of use.

SIZEHandset :

19 x 6 x 3.5cm (L x W xT)Maximum (Antennaexcluded)

Base Unit:21.5 x 16.5 x 5cm (L x W xT) Maximum (Antennaexcluded)

WEIGHTHandset :

250 grams

Base Unit:415 grams

POWER REQUIREMENTSHandset :

Self-contained nickel-cadmium rechargeablebattery supply, 3.6V nominal,600mAh capacity.

Base Unit:9VDC @ 500mA

MEMORYSpeed Dial:

25 Memory locations16 digits and 15 charactersper location.

CID:Alpha Numeric Display 50Memory locations

SPECIFICATIONS ARETYPICAL AND MAY CHANGEWITHOUT NOTICE.

4 1

91-5357-20-00ISSUED 0Printed in China

4 2

INTRODUCTION.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1SPECIAL FEATURES...........................................................................2

PARTS CHECKLIST... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

FCC REGULATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4IMPORTANT SAFETY INSTRUCTIONS.... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6INSTALLING THE BATTERY PACK.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

TO CHARGE THE BATTERY PACK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8A WORD ABOUT RECHARGEABLE BATTERIES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8REPLACING THE HANDSET BATTERY PACK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

SPARE BATTERY CHARGER/POWER BACK UP FUNCTION...... . . . . . . . . . . . . .9

GETTING STARTED..............................................................................10WALL MOUNTING.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11HANDSET LAYOUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12BASE LAYOUT... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13QUICK REFERENCE GUIDE...... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

SET-UP.... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14SETTING TIME.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14MAKING CALLS..................................................................................14ANSWERING CALLS................................................................................15TEMPORARY TONE.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15VOLUME CONTROL..............................................................................15RINGER CONTROL...... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15H O L D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 6MUTE.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16R E D I A L W I T H T H E H A N D S E T O N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 6R E D I A L W I T H T H E H A N D S E T O F F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 7PAGE/HANDSET LOCATOR... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17INTERCOM BETWEEN THE HANDSET AND THE BASE .. . . . . . . . . . . . . . . . . . . . .17CONFERENCE.... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19REVIEWING THE CALLER ID RECORDS..................................................19MEMORY DIALING....... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19FLASH................................................................................... ......................20

HANDSET SPEAKERPHONE FEATURE.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

SOFT MENU FUNCTIONS..................................................................21RDL(Redia l ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21MEM(Memory)......................................................................................22

MENU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

CALLER ID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24S A V E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 4D IAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25D E L ( D e l e t e ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 5CALLER ID - CALL WAIT ING ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26NOTES ABOUT CALLER ID & CALL WAITING ID. . . . . . . . . . . . . . . . . . . . . . . . . . . .26

TABLE OF CONTENTS

4 3

V O I C E A N N O U N C E C A L L E R I D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 6

P H O N E B O O K . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 7EDITING PHONE BOOK RECORDS& VOICE ANNOUNCE RECORDS........27

ADDING NEW PHONE BOOK RECORDS & VOICE ANNOUNCE RECORDS......28

O T H E R M E N U S E T T I N G S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 0R I N G E R T O N E / V O L U M E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 0K E Y B E E P O N / O F F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 0SET TIME. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31CLEAR ALL MEMORY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31AUTO ANSWER ON/OFF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32S E T T O N E / P U L S E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2

D E L E T E M S G I C O N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2

HEADSET OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33ADDIT IONAL OPERATING T IPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

OUT OF RANGE INDICATION.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34MESSAGE WAITING INDICATOR(for use with Voicemail)........................34O N E - T O U C H S E R V I C E K E Y S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 5CUSTOM FEATURES ........................................................................35LOW BATTERY INDICATION....................................................................36

CHECK AC POWER INDICATION.............................................................36

MAINTENANCE........ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37IN CASE OF DIFFICULTY............................................................38WARRANTY STATEMENT...... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39TECHNICAL SPECIFICATIONS.......................................................40

TABLE OF CONTENTS

introduction - centurylink

Documents