KG-1096 RATCHETING PEX CLAMP CINCH TOOL

One master cinch tool installs all sizes from 3/8" to 1" of Cinch Clamps.

With a unique “tab” design, the Cinch Tool goes into those hard-to-reach spaces.

Ratchet design releases only when the cinch clamp tab is properly pinched, thus ensuring a leak-proof connection.

Meets ASTM F-2098 specifications.

Compresses Stainless Steel Clamp Rings to secure PEX or PE-RT tubing to brass or poly crimp fittings.

WARNING! This product contains chemicals including DEHP, which is known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. For more information, go to www.P65Warnings.ca.gov.

OPERATION

1. Cut PEX tubing squarely, leaving a clean, even edge. Remove burrs.

2.Slide PEX cinch clamp over tubing and insert fitting. Place cinch damp l/8"-l/4

3.Place PEX cinch clampnub between tool jaws and ratchet the clamp until the PEX Cinch Clamp Tool auto-releases.

4. Pressure test the PEX tubing and inspect before normal use. If there are any signs of leaks, repeat the total procedure.

1/8"to1/4"

FEATURES

NOTE: Do not use with Zurn Quickclamp PEX crimp PEX crimp rings.R TM

SPECSTubing Compatibility: PEX

Fitting System Compatibility: clamp

Application:

Type:

3/8"PEX1/2"PEX5/8"PEX3/4"PEX

1"PEX

TOOL

CALIBRATION MODEL NO:KG1096

KG-1096 RATCHETING PEX CLAMP CINCH TOOL

ECCENTRICSTUD

RORATE COUNTER-CLOCKWISE TO INCREASE JAW GAP

ADJUSTMENTNUT

IN THE EVENT OF A JAWCOMPRESS HANDLES TORELIEVE PRESSURE ONRATCHET PULL RELEASELEVERIN DIRCTION OF ARROW

Do not use this tool to remove the clamps. Any use other than installation will void any and all warranties.

Clean tool per iodical ly to remove rust and dir t . Lubricate all parts after cleaning to provide a light protective coating of oil.

If tool operate becomes sluggish at any time, lubricate prior to further use.

Attention:

Do not use the Cinch Tool if it has been damaged, as this may result in an improper cinch. After repeated use of the Cinch Tool, it may require calibration. For convenience, a calibration gauge is provided in the tool box..

CLOSE HANDLETO STOP POINT INSERT GAGEINTO JAW GAP GAGE MUSTSTOP AT NO-GO IF GAGE GOESBEYOND THIS POINT RE-CALIBRATE TOOL

NO

-GO

GAGE

HOW TO REMOVE

1.loosen adjustment nut. 2.place go portion of gauge into jaw gap.

3.rotate eccentric stud counter-clockwise until jaws contact gage.

4.tighten nut. 5. check tool with gauge the first and last crimp on each job site.

IF IT’S IWISS, IT’S SECUREIF IT’S IWISS, IT’S SECUREIF IT’S IWISS, IT’S SECURE

Purchase the right toolis the key factor when tacking a large PEX project. Find what you will need from our wide selection of PEX tools.

WATER HEATER SOLUTION REPIPE PROGRAMNEW CONSTRUCTION

F1807 COPPER RING CRIMP TOOL

When connections are done properly, this should be a relatively last and inexpensive way of connecting PEX. There are a variety of different tools and crimp-ring manufacturers, and these products are relatively easy to purchase at a variety of retailers. The tools are generally one size fits all, so a 1/2-inch connection and a 1-inch connection can be made with no adjustment to the tool.

Benefits of PEX Clamp

IWS-FAS1/2",3/4",1"

IWS-FA 1/2’’, 3/4’’, 1’’

IWS-1234W 1/2’’,3/4’’

IWS-C 1/2",3/4"

F877 STAINLESS STEEL RING/V-GROOVED RING PRESS TOOL

IWS-1S 1"

IWS-34S 3/4"

IWS-12S 1/2"

IWS-S1234 1/2",3/4"

F2098 CLAMP RING CINCH TOOL

KG1096-K3/8" TO 1"

KG-1096 3/8" TO 1"

BJ0010C 3/8" TO 1"

F1960 EXPANSION RING EXPANDING TOOL

IWS-F1960MC 3/8", 1/2",3/4", 1"

IWS-F1960 1/2", 3/4", 1"