lok sabha sound system

TECHNOLOGY YOU CAN TRUST

INTERNATIONAL

Why do you go for sonic?We manufacture it with open mind to provide immediate replacement of

defective plug in modules.

We will not give an opportunity to write about the defects in the System by Engineer In Charge.

Tested in most sensitive places like Lok Sabha, Rajya Sabha, Bhopal Vidhan Sabha and Chhatisgarh Vidhan Sabha.

Technicians who have assembled and tested the equipment are available during running session.

INTERNATIONAL

ANNOUNCES A DRAMATIC NEW CONCEPT IN LISTENINGProfessional Launch

Unmatched performance and reliability have always been the hallmarks of as product and its designs. Any product should be built to last and withstand the rigors of daily usage.

We at Sonic understand this better than others. Our philosophy is to design and manufacture products capable of withstanding the most rigorous conditions. Years of association with the best in the world has taught us that both

Power and Sound are serious business.

Thus at Sonic we are dedicated to building superior quality Professional Amplifiers, Mixers, Equalizers, Tape Ampli deck, Reverb / Echo amplifier, Conference system, etc.

Products may look alike.........with Sonic the difference is in the design.

You will agree that Sonic is indeed superior.

SONIC INTERNATIONAL, C-38, 2nd FLOOR, STREET NO. 13, MADHU VIHAR, DELHI-110 092

Phone No. : 011-43628002, 65747203, 22247226 Mob No. +91 9810367083

Fax 42182282, E- mail: [email protected]

Website : www.sonicinternational.org

SONIC INTERNATIONALMAJOR INSTALLATION

*****

RAIL BHAVAN, PHD CHAMBER OF COMMERCE, JNU,

MAUSAM BHAVAN, DARBAR HALL BARODA HOUSE, DAV SCHOOL, NE RAILWAYS ETC

About us• Lok Sabha and Rajya Sabha sound system works on Sonic

International's equipment for over 15 years. It is an indigenous, custom built work horse system. The technology of sound system, digital microphone management, digital voting, and interpretation systems have been exclusively developed for specific needs of the Sabha(s) only by our company.

• All the installed system has a proven track record of zero failure for

the last 15 years. Our specially engineered custom-built digital automatic voting system installed with real time information on solid state display board is rated best in the world and maintained by our Company trained professionals who have manufactured the system. Installed hardware is not only future software intelligent but also completely fit for next / more than 5 years.

DELEGATE UNIT (CDU – 200)

A. Model CDU - 200 B. Type of Microphone Condenser electretsC. Polar response CardioidsD. Frequency response 125Hz - 12.5Khz.E. Type of Mic shaft Heavy duty rigid tube with goose-

neck piece 150 mm Shaft.F. Message Indication.G. Screen Printing of dial plate, Hindi / EnglishH. Single PCB designI. Distance between switches minimum 20 mm.J. Potential free contact for both hand use during voting.K. Touch Switch Mic: Mic-request / Mic-on

Voting PresentYesNoAbstain

L. Indicators Mic: Request / Mic-onVoting Vote nowYes (Green LED)No (Red LED)Abstain (Orange LED)Present (Amber LED)

M. Monitoring Floor channel by external low level LS with muting.N. Size 110 x 180 mm (back rows)

130 x 180 mm (two front rows)

Unique program technique.No SMD Components.

Replacement in 2 minutes.

CDU-200

Make Model No. List Price / MRP Sold Price for CPWD Date

SONIC CDU – 200 34,500/- 29,875/- 09/08/2012

CHAIRMAN UNIT (CCCU – 2000)

A. Model CCCU-200B. Type of Microphone Condenser ElectretsC. Polar response CardioidsD. Frequency response 125Hz - 12.5Khz.E. Type of Mic shaft heavy duty rigid tube with goose-neck

piece 380/450 mm Shaft.F. Screen Printing of dial plate, Hindi / EnglishG. Single PCB designH. Distance between switches minimum 20 mm.I. Intercom handset for private communication between Chairman and secretary. J. Touch Switch Mic: Mic-on / Mic-off

PriorityCancel all requestSpeaking Time

Screen: Mic / VotePage

K. Indicators Mic: Mic-onSpeaking Time activePriority

Voting Vote activeL. Monitoring floor channel by external low level

LS with muting

CCCU-2000


SONIC CCCU – 2000 2,05,000/- 1,75,000/- 11/03/2010

SECRETARY GENERAL UNIT (CCSG – 2000)A. Model CCSG - 2000B. Type of Microphone condenser electretsC. Polar response CordioidD. Frequency response 125Hz - 12.5Khz.E. Type of Mic shaft heavy duty rigid tube with

goose-neck piece 380/450 mm Shaft.

F. Screen Printing of dial plate, Hindi / EnglishG. Single PCB designH. Distance between switches minimum 20 mm.I. Mechanical Switch Key for Voting.J. Intercom handset for private communication between Chairman and secretary. K. Touch Switch Mic Mic-request / Mic-on

Screen: Mic/VotePage

Voting: Start votingStop votingOpen / Secret votingAttendance checkClear resultStart / Free Voting

L. Indicators Mic: Mic-onVoting Vote activeSecret Voting

M. Monitoring floor channel by external low level LS with muting.

CCSG- 2000


SONIC CCSG – 2000 2,35,000/- 1,63,000/- 14/03/2012

ADDITIONAL UNIT (CDU – 200 B)

Additional Units for Hon’ble Speaker, PM, FM, Leader of Opposition, Oath & witness: -

A. Oath & witness:

Handheld Microphone without request switch.Microphone connection socket.Digital Interface as required.Floor Stand,

B. Hon’ble Chairman Unit:

Flush mounted as per existing layout.Gooseneck microphone with 380/450 mm Shaft.Microphone connection socket.Digital Interface unit as required.

C. Hon’ble PM, FM, Leader of Opposition:

Flush mounted as per existing layout.Gooseneck microphone with 380/450 mm Shaft.Microphone connection socket.Digital Interface unit as required.

CDU – 200 B


SONIC CDU– 200 B 34,500/- 30,050/- 10/11/2011

REPORTER UNITa. Language selector with headphone.b. Low level Loudspeaker.

I). LANGUAGE SELECTORS - LS - 1000A. Model LS-1000B. No. of channels 4 (OR+3)C. Connector type 3.5 mm jackD. Frequency response according to IEC 914E. Max. power output 100mWF. Size 50 x 120mm2). HEAD PHONE - K - 15A. Unbreakable Construction.B. Type : Dynamic.C. Frequency response : 125 Hz to 12.5 Khz.D. Impedance : 300 Ohms.E. Power handling capacity : 250 mw.F. Sensitivity : (1KHz)102db.G. 3.5 mm mono plug with 1½ meter cable.H. Foams can be replaced easily.3). CEILING SPEAKER - CS - 16Operating Power : 9 Watt RMS. Maximum Power : 16 Watt RMSFrequency Response : 85Hz to 16KHz (-10db)

90Hz to 12KHz (-3db)Power Tapping : 5W, 10W, 15WDimensions (mm) : 230 Ø X H75Weight : 0.80 Kg

LS-1000

K-15

CS-16


SONICSONICSONIC

LS-1000K-15

CS-16

1, 800/-1, 800/-1, 800/-

1, 555/-1, 555/-2,400/-

09/08/201209/08/201214/04/2010

Interpreter Desk Units DIC-82 (8 Language Dual Interpreter Console).

Interpreter desk unit with LED displayGooseneck microphone with min 300 mm shafts.Dynamic interpreter Headphone.Intercom handset for private communication with operator.

Simultaneous Interpretation System (SIS) control console MAPU-200/MAC-4The SIS control console is a 19" rack mounted module witch will hold all necessary electronics and amplifier for the control and distribution of up to 8 channels (Original +7 interpreted languages).The distribution will be wire bound.Not used channels will be automatically switched to the original language.The states of each channel can be monitored on this console by two LED indicators “OR/INT” showing if the channel is occupied by an interpreter.The console is connected to the interpreter stations and to the channel-selector-unit in single cable technology. Simultaneous Interpretation facilityEach delegate will be provided with

- a headphone- a volume control- a selector switch

For seven interpreted and one floor languages.Changeover console for interpretation system (MAC-200)

DIC-82

MAC-200

MAC-4

INTERPRETER UNIT


SONICSONICSONIC

DIC-82MSC-200

MAC-4

95,000/-68,500/-

1,10,500/-

81,590/-59,950/-83,900/-

26/08/201006/07/200401/12/2011

FEATURES

1) System shall record analogue audio signal in the form of digital.

2) 8 bit / 16bit /32bit/64bit.

3) Every 5 minutes /10 minutes audio file shall be created automatically in MP3 format.

4) 12 digit file name shall be created automatically.

5) Up to one minute buffer can be added to any recorded MP3 file automatically.

6) Five minute proceeding in one floppy disk (1.1MB).

7) Quality of sound shall be good and it can be played in any computer.

COMPUTER

SONIC DIGI-PRO SOFTWARE 1.4

DIGITAL RECORDING AND TRANSCRIPTION SYSTEM (DRS-200)

From analogOutput of

Distributionamplifier


SONICSONIC

DRS-200SOFTWAREDIGI-PRO

7,25,000/-2,12,000/-

7,15,000/-2,08,075/-

08/11/200608/11/2006

DESCRIPTION DDSP-200 System consists of two number of Digital Signal Processor (DSP-200) along with auto manual switch.One processor will act as main processor and other processor will act as true hot standby. The changeover from one processor to another is very smooth and a 9 pin data connector is available for connecting. DDU-200 which can be plugged/removed without any disturbance to the system.Hence it consists of two numbers of Central Processor Module (PM-1), along with 4 nos. of control processor module (PM-2) and 4 nos. of Switched Mode Power Supply PSU-110.Central Processor Module (PM-1) Uses 8751 Processor as master & can drive up to 2 control modules. 4 process elements can be identified and controlled through software.Control Processor Module (PM-2) Uses 8751 Processor as slave with (PM-1). It can also drive 32 Process elements through software.Switched Mode Power Supply (PSU-110)The PSU-110 Series of compact, open PCB constructed with AC-DC switching power supplies are capable of delivering 110 watts of continuous power at 25°C FM forced air cooling or 80 watts air convection cooling. They operate at 85 to 280 VAC input voltage without changing the Jumper, all outputs are fully regulated. This PSU-110 is quite suitable for DSP with micro controllers.Extra FeaturesThe power supply switch, the address dip switch, auto manual switch are brought in the front LED indication for two power supply conditions, data status, for both the processors. Powder painted aluminum extruded chassis. It occupies 3U size and suitable for 19” rack.

COMPUTER CONTROLLED CONFERENCE SYSTEMSYSTEM ELEMENTS - DUAL DIGITAL SIGNAL PROCESSOR (DDSP-200)


SONIC DDSP-200 6,35,000/- 5,82,000/- 13/02/2009

DESCRIPTION

Display Driver Unit DDU-200 is capable of sending Voting and Attendance digital data’s of 128 members in the form of Ayes, Noes, Abstain (O), and Presence to the individual Result Display Board (IRD).In order to achieve a real time display it uses one master processor 8031 with a special address and two slave processors around micro controller 8031. All the processor modules (one master processor and two salve processors) are with 62 pin

gold contacts for proper digital transmission.The processor printed circuit boards are computer design stimulated boards with minimum track width of 0.4mm. The processor boards are plug in type and the slave boards are interchangeable.Uses the ISA sockets for our entire plug in processor cards for firm connection. All the ICs are inserted in round IC sockets for easy replacement.Since the member can changes vote results are many times during the voting cycle the main along with slave processor uses high speed data handing EPROM’s around 15mS. The data is updated in every 15 mS for displaying the results in the display board. The output of this unit is in RS232 format.Uses our Switched Mode Power Supply SMPS-PSU-110. The status of power supply +24V, 5V are indicated by LED‘s at the front. Flashing LED monitors the output data.One more Digital display driver DDU-200 (1 master processor modules + 2 salve processor + motherboard + SMPS) in the same 2U chassis with auto / manual changeover. Model no. DDDU-200.Uses Black powder painted die cast Aluminum channel chassis.Suitable for 19" rack with 2U size.

COMPUTER CONTROLLED CONFERENCE SYSTEMSYSTEM ELEMENTS - DUAL DISPLAY DRIVER UNIT DDDU-200

Make Model No. List Price/MRP Sold Price for CPWD Date

SONIC DDDU-200 5,90,000/- 5,66,000/- 23/09/2008

FEATURES

• Geographic keyboard is designed on the basis of latest digital technology.

• Touch switches along with 3mm LED’s are arranged as per the seating arrangements (geographic fashion) so that the operator can switch ON/OFF any microphone in AUTO or MANUAL mode.

• When the member presses the red button from his delegate unit a corresponding LED starts flashing in the geo graphic key board. The microphone will be put ON by the operator and the LED corresponding to the unit lights up in the geographic board. The operator can switch OFF his microphone (in case the member forgets to switch OFF after the speech is over) by pressing the corresponding touch switch. The microphone can also be actuated ON from the geographic keyboard without the request of the member.

* It uses three number of interface controller like sonic PM-3.

• One monitor speaker along with level control is provided in the geographic key-board. •Chairman unit’s audio level control and Delegate unit’s audio level control are also provided in the geographic key-board, as these are voltage controlled.

• Sleek in design, thus occupies less space in the control room.

DIGITAL GEOGRAPHIC KEY BOARD- (GMFB-575)

GMFB-575


SONIC GMFB-575 14,45,000/- 14,02,789/- 14/03/2012

FEATURES

Sonic Introduces new range of audio processors digital and analog.

• Sonic VCM-28 is one among the special featured analog audio processor for distributing the audio signals for long distances without introducing electromechanical noise pickup. The frequency response is also maintained as original. Special toroidal transformer is used to improve the signal to ratio noise. Voltage controlled amplifiers (VCA) are introduced in the audio chain to increase or decrease the audio level without introducing the carbon track noise of rotary control. Since the audio level is controlled from VCA, the mixer can be controlled remotely without using shield cables. Inputs and outputs through Stereo 1/4 inch phono connectors. VCM-28 has two inputs to accept 0dB audio signal which is mixable and provides eight transformer isolated outputs of 0dB. 5 LED Array for monitoring all the eight outputs. Each input/output can be monitored by a headphone. Eight VCA rotary controls for adjusting the level of outgoing audio signals. Two more rotary controls for adjusting the level of inputs. Uses regulated plus and minus power supply voltage status indicated by green and orange LED’s in the front. Can be used as Zone selector. Our Wireless Interface WI - 200 / Audio Processor Mixer APC - 82 can be connected to the mixer for additional features. 9 Pin D Type Connector for remote operation. Standard 19 inch rack mounting facility.

Specification

• Line input Imp : 10 Kohm • Line gain range : 0 to + 20 db Freq response : 50Hz to 15KHz Output Impedance : 200 ohm Output Over Drive: 24 dbv THD + Noise: < 0.02% S/N Ratio > 85db Weight: 5kg

AUDIO PROCESSOR - VOLTAGE CONTROLLED MIXER - (VCM - 28)


SONIC VCM-28 72,000/- 57,181/- 14/03/2010

FEATURES

Sonic Introduces new range of audio processors/ changeover for digital and analog.

• Sonic M85 changeover / VCM-28C is one among the special featured analog audio processor changeover for distributing the audio signals for long distances without introducing electromechanical noise pickup. The frequency response is also maintained as original.

• Basically it changes the main and standby audio processor inputs and outputs through relays.• Since the audio level is controlled from VCA, the mixer can be controlled remotely without using shield cables.• Inputs and outputs through Stereo 1/4 inch phono connectors.• 2 inputs and 8 outputs are switched through omran relays for noiseless changeover of processors through switches.• Uses regulated plus and minus power supply voltage status indicated by green and orange LED’s in the front.• Our Wireless Interface WI - 200 / Audio Processor Mixer APC - 82 / Voltage Controller Mixer VCM - 28 can be

connected to the mixer changeover for additional features. • 9 Pin D Type Connector for remote operation through CHINTCO.• Standard 19 inch rack mounting facility.• Weight: 4kg.

AUDIO PROCESSOR CHANGEOVER M85 CHANGEOVER / VCM28C


SONIC VCM-28 C 46,500/- 35,027/- 14/03/2010

FEATURES

Sonic Introduces new range of audio processors digital and analog.• Sonic APC-82 is one among the special featured analog audio processor for distributing the audio signals with 8 nos of

Zero Ohm amplifiers for long distances without introducing electromechanical noise pickup. The frequency response is also maintained as original. Special toroidal transformer is used to improve the signal to ratio noise. Voltage controlled amplifiers (VCA) are introduced in the audio chain to increase or decrease the audio level without introducing the carbon track noise of rotary control. Since the audio level is controlled from VCA, the mixer can be controlled remotely without using shield cables. Inputs and outputs through Stereo 1/4 inch phono connectors. APC-82 has six inputs to accept MIC-A and MIC-B balanced outputs of delegate units (max-128 nos.) from 4 Port of Sonic DDPS-200 and two inputs to accept MIC-A and MIC-B of chairman units(max-64 VVIP units) from 2 Port of Sonic DDPS-200. Both the inputs are not mixable and provides 2 independent output suitable for Voltage controlled amplifier Sonic VCM-28.. 5 LED Array for monitoring all the eight inputs. Each input/output can be monitored by a headphone. Eight VCA rotary controls for adjusting the level of input audio signals. Two more rotary controls for adjusting the level of mixed 6 inputs level and mixed 2 inputs. Uses regulated plus and minus power supply voltage status indicated by green and orange LED’s in the front. Can be used as Zone selector. Our Wireless Interface WI - 200 can be connected to the mixer for additional features. 9 Pin D Type Connector for remote operation. Standard 19 inch rack mounting facility.

Specification• Line input Imp : 10 Kohm • Line gain range : 0 to + 20 db Freq response : 50Hz to 15KHz Output Impedance : 200 ohm Output Over Drive: 24 dbv THD + Noise: < 0.02% S/N RatiO > 85db Weight: 5kg

AUDIO PROCESSOR - VOLTAGE CONTROLLED MIXER - (APC-82)


SONIC APC-82 3,35,000/- 2,62,701/- 14/03/2010

FEATURES

Sonic Introduces new range of audio processors digital and analog.

• Sonic WI - 200 is one among the special featured analog audio processor for accepting the audio signals from different audio sources (four) without introducing electromechanical noise pickup. The frequency response is also maintained as original. Special toroidal transformer is used to improve the signal to ratio noise. Compressor Limiters are introduced in each and every audio chain to take care of feedback without introducing the carbon track noise of rotary control. The audio level of each input is controlled through rotary control and indicated by an LED. Each input can be put on and off by a touch switch. Inputs and outputs through Stereo 1/4 inch phono connectors.WI-200 has four inputs to accept from -10 dB to +3 dB audio signal which is mixable and provides one balanced output suitable for Zero ohm amplifier like VCM - 28. FM Receiver/USB Audio is also provided as one of the inputs. Uses regulated plus and minus power supply voltage status indicated by green and orange LED’s in the front. Our Voltage Controlled Mixer VCM - 28 / Audio Processor Mixer APC - 82 can be connected to the interface for additional features. Wireless microphone can be connected without any feedback. Standard 19 inch rack mounting facility.

Specification• Line input Imp : 10 Kohm • Line gain range : 0 to + 20 Db Freq response : 50Hz to 15KHz Output

Impedance : 200 ohm Output Over Drive: 24 dbv THD + Noise : < 0.02% S/N Ratio > 85db Weight: 5kg

WIRELESS INTERFACE- (WI-200)


SONIC WI-200 60,000/- 52,540/- 14/03/2010

PROFESSIONAL MOSFET AMPLIFIER (MOSA-1000)

SPECIFICATIONS:Output Power: 8 OHMS Stereo 300+300

Watts: 4 OHMS BTL600 Watts

Power Bandwidth: 20Hz to 20KHz

Frequency Response: 10Hz to 20KHz at Full

Rated Output Power

Slow ratio: 2 Micro seconds

IMD: Less than 0.01% from

250mW to full rated

power. 60Hz to 7 KHz

4:1SMPTE

THD: Before clip 20Hz to 20KHz

at all load impedance THD

typically at 0.005% at 8O

HMS before Clip.

Tone switches: Loudness +5db at 100Hz

Cut Below 30Hz -12dB/ Octave Cut -12dB/ Octave

below 30Hz

70V line capability: BTL Mode 8 OHMS

Hum and noise: 110dB below the full

rated output. A Weighed

Output Devices: Fully complimentary circuit

design utilizing 8x150 watts

mosfets.

Connections: 2x 1/4” phono jacks Balanced

and unbalanced 2x XLR Locking

Connectors Balanced and un-balanced 5 way bending post output.

Input Impedance: Balanced 20 KOHMS Unbalanced

10 KOHMS

Protections: Failure supply is indicated by RED

LED on top of the fuse.

Power cord: 14 GAUGE

Construction: Rugged. Frame type.


SONIC MOSA-1000 35,000/- 33,317/- 05/07/2008

DISTRIBUTION AMPLIFIER - (DA - 82)

FEATURES:Sonic Introduces new range of audio processors

digital and analog.• Sonic DA-82 is one among the special featured analog audio

processor for distributing the audio signals for long distances without introducing electromechanical noise pickup. The frequency response is also maintained as original.

• Special toroidal transformer is used to improve the signal to ratio noise.

• Voltage controlled amplifiers (VCA) are introduced in the audio chain to increase or decrease the audio level without introducing the carbon track noise of rotary control.

• Two more rotary controls for adjusting the level of two inputs.• Uses regulated plus and minus power supply voltage status

indicated by green and orange LED’s in the front.• 2 Aux inputs of 200mV is also provided at the rear.

• 25 Pin D Type Connector for remote operation.• Standard 19 inch rack mounting facility• Two more rotary controls for adjusting the

level of two inputs.

SPECIFICATION:

• Line input Imp : 10 Kohm

• Line gain range : 0 to + 20 db

• Freq response : 50Hz to 15KHz

• Output Impedance : 200 ohm

• Output Over Drive : 24 dbv

• THD + Noise : < 0.02%

• S/N Ration : > 85db


SONIC DA-82 71,000/- 64,500/- 15/03/2006

FEATURES

Six doom cameras in the chamber can constantly provide video outputs. The Moment a member starts speaking the hex output corresponding to his/her seat in the geographic location switches ON the corresponding camera and focuses the member whose mic is ON which is programmed in our PM-3 Interface.

Since Lok Sabha TV is already having a HD digital cameras in the chamber, the RS 232 Serial data of the camera and the HEX output of the delegate unit can be synchronized by programming in PM-3 Module.

2 nos. of PM-3 Module, one as main and other as standby is housed in a 2U chassis for 19” rack facility.

AUTOMATIC CAMERA CONTROL AND DISPLAY - ACS-2000


SONIC ACS-2000 7,25,000/- DEMO STAGE 2011

INDIVIDUAL RESULTS DISPLAY PANEL

It displays the individual results like Ayes, Noes, Abstain and Present results. ‘Vote Now’ lamps are provided on both side of the board.IRD boards located on either side of the presiding officer’s seat, arranged in a geographical

layout similar to the seating arrangement of the voting system. For each member, the corresponding division number is indicated on the panel along with LED display array which shows:

— a green “A” for “AYES”— a red “N” for “NO”— a yellow “O” for “ABSTAIN”— a amber “P” for “PRESENT”

Individual results will be shown instantaneously changing while voting and will be “frozen” at the end of voting. Individual results are shown by the three characters “A”, “N” or “O” on the individual result display panel.

TOTAL RESULTS DISPLAY PANEL (TRD)

It displays the final results after the voting period is over.Each LED Display Board has five lines as in the following illustration:

AYES 002 NOES 001 ABEST 001 TOTAL 004 TIME

INDIVIDUAL + TOTAL RESULT DISPLAY (IRD + TRD)

IRD+TRD+LAMP(test mode)

TRD(test mode)

Make Model No. List Price/MRP Sold Price Date

SONICSONIC

TRD-4332IRD-5600

9,50,000/-20,00,000/-

DEMODEMO

20052005

VOTING TIME DISPLAY (DTDU-200)

Voting Time Display to show the count down timing from 10sec to 0sec with synchronization with the digital signal processor.

SPEAKING TIME CLOCK (STC-200)

There are 3 buttons in the clock remote switching console, the functions are as follows The chairman/operator has to START the speaking time clock every time when the microphone is ON and OFF.

The PAUSE button has to be pressed in case some one interrupts for adding the speaking time.

The CLEAR / RESET button to be pressed before the start the next member.

TIME DISPLAY UNIT(2 DIGIT) - DTDU-200 LARGE SACLE HALL DISPLAY (LSHD)

VOTING TIME DISPLAY

LSHD

LARGE SCALE HALL DISPLAY (LSHD-200)

It display with five/six lines and 22 characters per line to display in Hindi/English in following mode. It accepts the signal from PM3 in RS 232 format.

1. Manual Mode

2. Automatic Mode

3.Voting Mode

4. Message Mode

5. Speaking Time Mode

Make Model No. List Price/MRP Sold Price for CPA BHOPAL Date

SONICSONICSONIC

DTDU-200STC-200

LSHD-200

1,38,000/-3,50,000/-

20,00,000/-

1,25,000/- (CPWD)3,21,600/- (CPWD)

19,50,000/- (CPA, BPL)

10/03/200615/10/200704/07/2007

INTERCOM FACILITY FOR MARSHAL

Intercom facility for Marshal:

A. Intercom Handset for private communication with Operator with interface unit (DDI) etc as required.

B. Talking Phone: Up to 5KM.C. Can Communicate with all brands Radio.D. Non-License Walkie talkie.E. Selective ChannelsF. LCD Backlit DisplayG. Auto Channel Scan.H. Page Tone AlertI. Low Battery Alert.

J. Optional Accessories:- Rechargeable Battery ( 4 X AAA Size)- Charging Adaptor- Ear Phone.WT-200

Make Model No. List Price/MRP Sold Price for CPA BHOPAL Date

SONIC WT-200 12,800/- 12,500/- 23/09/2004

DESCRIPTION

It is a Professional Dynamic Mixer with remote operation. It is having 15 identical channels and the channels are tuned for the Shure mic SM48/SM58. Each channel is balanced in nature for noise free pickup. The special circuit with digital technology makes the switching without any noise. The channel level can be adjusted from the front for mic or line input without changing the input jacks. The output is available in two levels. The mixer can be cascaded with another mixer using the mixer bus, which is provided at the rear of the equipment. The output level is indicated by a 5 LED array as well as can be monitored by a headphone an LED indication is provided at the front to show the status of the mic whether the microphone is ON or OFF. The switching logic is taken out through 36 pin ceotronics connector which is suitable for Sonic GMFB-100. The equipment is made out of Aluminums channel chassis for less RF interference. The equipment occupies 2 U size in 19 inch rack. It also uses the toroidal transformer for improved S/N ratio.

REMOTE DYNAMIC MIXER (RDM-15)

T.E.I.N. (DIN Audio)MIC input, 150 Ohms source : -128.5dBLINE input, 10 Ohms source : -98.5dBmT.H.D and NOISE : <0.08%FREQUENCY RESPONSE : +0-1dB0dBm, 600 Ohms MIC input toL/R output : 25 Hz to 19 KHzIMPEDENCEMIC input : Typically 2K Ohms

LINE input : 20K Ohms (balanced)10K Ohms (balanced)

L/R output : <50 OhmsAux sends : <50 OhmsAux returns : >10K OhmsTape records : <2K OhmsTape playback : >20K OhmsGAIN RANCEMIC input : 62dBLINE input : 42dB


SONIC RDM-15 92,000/- 75,300/- 16/09/2003

PLUG IN MODULES WITH GOLD CONTACTS

SOLID STATE DISPLAY BOARDUsing LED Module.

LOK SABHA CONTROL RACK

Sound System,Interpretation System

& Voting System.

All equipments manufactured by

SONIC INTERNATIONAL

MP Vidhan SabhaCONTROL RACK

Sound System,Interpretation

System & Voting System.


SONIC INTERNATIONAL

Chattisgarh Vidhan Sabha

CONTROL RACKSound System,Interpretation

System & Voting System.


SONIC INTERNATIONAL

Available improvementsThe following slides give a detailed description of the improvements possible in

The existing system. Click on the link below to view.

Video Interface http://www.slideshare.net/sonicinternational1994/videointerface

Real Time System http://www.slideshare.net/sonicinternational1994/real-time-15381048

Time management and Speaking time clockhttp://www.slideshare.net/sonicinternational1994/time-management-15380976

Digital Recording System http://www.slideshare.net/sonicinternational1994/digital-recording-15380440

Demo Voting System

http://www.slideshare.net/sonicinternational1994/demo-voting

Interpreter monitoring System

already implemented in Lok Sabha Sound System.

http://www.slideshare.net/sonicinternational1994/videointerface

http://www.slideshare.net/sonicinternational1994/real-time-15381048

http://www.slideshare.net/sonicinternational1994/time-management-15380976

http://www.slideshare.net/sonicinternational1994/digital-recording-15380440

http://www.slideshare.net/sonicinternational1994/demo-voting

Digital Lab

Video Interface

TRD IRD

LSHD TRD IRD

Control Rack

Standby Equipments

GMFB Stimulation

DSP Stimulation

Advantage over the Imported Equipments

• Distance from the speaking person to the microphone-2 feet (max).• Delegate unit replacement in 2 minutes time when the system is in

offline.• No programming of Delegate Units is required.• Inter connection of Delegate Units by 1mm terminal silver pins and

loop cable by 9 pin D type connectors.• If microphone is mishandled, it will still work properly.• All equipments with plug-in module facility.• All equipments PCB’s with minimum 0.4 mm copper track

thickness.• All equipments with virtual service kit facility for immediate

rectification.• Equipments like Delegate units, SG unit, Chairman unit, Language

selectors, Interpreter units are designed in such a way that there is no modification in the existing wooden furniture.

• SI (Simultaneous Interpretation System) functionality is monitored by the Data Time Log System.

• IRD (Individual Result Display System), TRD (Total Result Display System) and LSHD (Large Hall Display System) are all solid state design from safety point of view in the chamber.

• Digital recording facility with time overlap suitable for Reporters.• Functionality of the entire control equipments by LED’s visual

indication.• Number of loop cables are very less.• All the components in the control system equipments are easily

available in the market.• All equipments are indigenously developed to meet the Indian

custom built environment.• No SMD (surface mount component) components.• No special tool is required for servicing of equipment.• Cables are manufactured in such a way that there can be no pest-

infestation.

• Single cable technology - Full system with A10 Cable.• All the equipments can withstand all types of voltage fluctuation.• Technicians who have assembled, wired and tested the

equipments are available during the running session for maintenance.

• Specialist who designed the system is available during sensitive electronic voting.

• Maintenance charge is very low.• Voting Free - option from SG’s unit.• Solid State Digital Geographic keyboard with special functional

keys for easy operation.• 575 microphones cannot be operated by touch screen monitor when

more than 20 microphones need to be switched “ON” at different location of the chamber at the same time.

• Stand-by sound system of the Lok Sabha is also operated by the geographic keyboard.

• Virus cannot attack the system computer.• Processor speed 2.8 GHz.

• System boot time 15 seconds.• The system can be operated with Windows 98/ XP / 7 /8.• Proven record of 15 years old for analog and digital Service

centre in 12 km distance.• Since all control equipments from a single company, matching is not

a problem.• Indian equipments for Indian Parliament.• The low level speakers which are in front of the members act as re-

enforced sound systems for the main as well as the stand-by system.

• The audio chamber is distributed through 5 DDPS, hence, in case of a failure of any row, the front and the back row microphones can be switched on with negligible time lag and will be unnoticeable.

• Digital voting system with solid state real time display is fully functional only in Indian parliament.

• High-end professional conference system for any sensitive installation in India is always accompanied by highly reliable Ahuja dynamic microphone, but since our systems are reliable, no such addition is incorporated.

• 575 microphones are distributed through 8 numbers of zero ohm amplifiers, hence the total 24 microphones can be put ON without any noticeable difference in audio level/quality.

• Microphone management system, simultaneous interpretation system and voting system are all independent. Low level sound re-enforcement system speakers are driven by a separate power amplifier, hence the speaker system is also independent of the above three systems.

• During the running session, serviceability below the chamber is not permissible , hence our system doesn’t use any active electronic equipment below the chamber, which could cause any disturbance.

• Our special SMPS PSU-100 has a unique current sensing circuit, suitable for Indian power fluctuations.

• During short-circuit or humid environment, it shuts down the power mosfet driver and prevents smoke and fire inside the chamber.

• SI system with four languages is switched through 100 matrix switches and low level speakers with 25 matrix switches to isolate the faulty loop.

• SI with 8 language interpretation system is working without any special software.

• In a running session, the Speaker can mute his/her microphones when there is a verbal communication with the Secretary General or the Marshal.

• Voting cycle can be initiated from 2 places, either from the Secretary General Unit or from system computer in the sound control room. In case of failure of the Secretary General unit, the voting can be initialed from the sound control room.

• In case the main audio processor or main SI unit or main sound system or main interpreter system fails it goes to standby processor by flick of an A/M switch.

• In case the main Digital Processor or Digital Display Unit or main system computer fails, it goes to the hot Standby Unit automatically.

• Many improvements are possible in the existing system and demo is available.

• 24 microphones in the chamber can be switched “ON” at a time.• Sound clarity in the chamber can be improved by 3dB app by using

the same chairman mic capsule to delegate mics. • Since the audio bus is separate, failure/short of digital bus will not

affect the microphone management system.• The service time for the chamber in the morning is 1 hr (max), the

present “audio test “ in front of the microphone is the best option.• Original audio is reproduced.

• Record of 48 hrs of non-stop operation with electronic voting at the end.

• Voting result can be printed out using a laser printer in one minute with result of 50 members in one page.

• Press and Visitor’s gallery uses cost-effective, reliable heavy duty language selectors.

• No wall mounted or line array column speaker in the chamber, hence the chamber aesthetic is not disturbed.

• No failure reported even when the electric power supply along with UPS failed 14 times since installation.

• We have set standard for Lok Sabha, Rajya Sabha and Vidhan Sabha.

• Maintenance without spare equipments for over 15 years, based on confidence in our products.

• Saved crores of rupees for the past 10 years.• Can save public money @ Rs.1 crore per year.

THANKYOU!

lok sabha sound system

Technology