micom p441, p442 & p444

MiCOM P441/P442 & P444 Numerical Distance Protection

P44x/EN T/I95

Software Version: C7.x, D4.x, D5.x & D6.x Hardware Version: J, K

Technical Guide

Note: The technical manual for this device gives instructions for its installation, commissioning, and operation. However, the manual cannot cover all conceivable circumstances or include detailed information on all topics. In the event of questions or specific problems, do not take any action without proper authorization. Contact the appropriate Schneider Electric technical sales office and request the necessary information.

Any agreements, commitments, and legal relationships and any obligations on the part of Schneider Electric including settlements of warranties, result solely from the applicable purchase contract, which is not affected by the contents of the technical manual.

This device MUST NOT be modified. If any modification is made without the express permission of Schneider Electric, it will invalidate the warranty, and may render the product unsafe.

The Schneider Electric logo and any alternative version thereof are trademarks and service marks of Schneider Electric.

MiCOM is a registered trademark of Schneider Electric. All trade names or trademarks mentioned herein whether registered or not, are the property of their owners.

This manual is provided for informational use only and is subject to change without notice.

2012, Schneider Electric. All rights reserved.

CONTENTS

SS Safety Section Pxxx/EN SS/G11

Section 1 Introduction P44x/EN IT/I95

Section 2 Technical Data P44x/EN TD/I95

Section 3 Getting Started P44x/EN GS/I95

Section 4 Settings P44x/EN ST/I95

Section 5 Application Notes P44x/EN AP/I95

Section 6 Programmable Logic P44x/EN PL/I95

Section 7 Measurements and Recording P44x/EN MR/I95

Section 8 Firmware Design P44x/EN FD/I95

Section 9 Commissioning P44x/EN CM/I95

Section 10 Maintenance P44x/EN MT/H85

Section 11 Troubleshooting P44x/EN TS/H85

Section 12 SCADA Communications P44x/EN SC/I95

Section 13 Symbols and Glossary P44x/EN SG/I95

Section 14 Installation P44x/EN IN/I95

Section 15 Cyber Security P44x/EN CS/H85

Section 16 SW/HW Version History and Compatibility P44x/EN VH/I95

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

Pxxx/EN SS/G11

SAFETY SECTION

Pxxx/EN SS/G11 Safety Section Page 1/8

STANDARD SAFETY STATEMENTS AND EXTERNAL LABEL INFORMATION FOR SCHNEIDER ELECTRIC EQUIPMENT

1. INTRODUCTION 3

2. HEALTH AND SAFETY 3

3. SYMBOLS AND EXTERNAL LABELS ON THE EQUIPMENT 4

3.1 Symbols 4 3.2 Labels 4 4. INSTALLING, COMMISSIONING AND SERVICING 4

5. DECOMMISSIONING AND DISPOSAL 7

6. TECHNICAL SPECIFICATIONS FOR SAFETY 8

6.1 Protective fuse rating 8 6.2 Protective Class 8 6.3 Installation Category 8 6.4 Environment 8

Pxxx/EN SS/G11 Page 2/8 Safety Section

BLANK PAGE


1. INTRODUCTION This guide and the relevant equipment documentation provide full information on safe handling, commissioning and testing of this equipment. This Safety Guide also includes descriptions of equipment label markings.

Documentation for equipment ordered from Schneider Electric is despatched separately from manufactured goods and may not be received at the same time. Therefore this guide is provided to ensure that printed information which may be present on the equipment is fully understood by the recipient.

The technical data in this safety guide is typical only, see the technical data section of the relevant product publication(s) for data specific to a particular equipment.

Before carrying out any work on the equipment the user should be familiar with the contents of this Safety Guide and the ratings on the equipments rating label.

Reference should be made to the external connection diagram before the equipment is installed, commissioned or serviced.

Language specific, self-adhesive User Interface labels are provided in a bag for some equipment.

2. HEALTH AND SAFETY The information in the Safety Section of the equipment documentation is intended to ensure that equipment is properly installed and handled in order to maintain it in a safe condition.

It is assumed that everyone who will be associated with the equipment will be familiar with the contents of that Safety Section, or this Safety Guide.

When electrical equipment is in operation, dangerous voltages will be present in certain parts of the equipment. Failure to observe warning notices, incorrect use, or improper use may endanger personnel and equipment and also cause personal injury or physical damage.

Before working in the terminal strip area, the equipment must be isolated.

Proper and safe operation of the equipment depends on appropriate shipping and handling, proper storage, installation and commissioning, and on careful operation, maintenance and servicing. For this reason only qualified personnel may work on or operate the equipment.

Qualified personnel are individuals who:

Are familiar with the installation, commissioning, and operation of the equipment and of the system to which it is being connected;

Are able to safely perform switching operations in accordance with accepted safety engineering practices and are authorised to energize and de-energize equipment and to isolate, ground, and label it;

Are trained in the care and use of safety apparatus in accordance with safety engineering practices;

Are trained in emergency procedures (first aid).

The equipment documentation gives instructions for its installation, commissioning, and operation. However, the manual cannot cover all conceivable circumstances or include detailed information on all topics. In the event of questions or specific problems, do not take any action without proper authorization. Contact the appropriate Schneider Electric technical sales office and request the necessary information.


3. SYMBOLS AND EXTERNAL LABELS ON THE EQUIPMENT For safety reasons the following symbols and external labels, which may be used on the equipment or referred to in the equipment documentation, should be understood before the equipment is installed or commissioned.

3.1 Symbols

Caution: refer to equipment documentation

Caution: risk of electric shock

Protective Conductor (*Earth) terminal

Functional/Protective Conductor (*Earth) terminal. Note: This symbol may also be used for a Protective Conductor (Earth) Terminal if that terminal is part of a terminal block or sub-assembly e.g. power supply.

*NOTE: THE TERM EARTH USED THROUGHOUT THIS GUIDE IS THE DIRECT EQUIVALENT OF THE NORTH AMERICAN TERM GROUND.

3.2 Labels

See Safety Guide (SFTY/4L M/G11) for equipment labelling information.

4. INSTALLING, COMMISSIONING AND SERVICING

Equipment connections

Personnel undertaking installation, commissioning or servicing work for this equipment should be aware of the correct working procedures to ensure safety.

The equipment documentation should be consulted before installing, commissioning, or servicing the equipment.

Terminals exposed during installation, commissioning and maintenance may present a hazardous voltage unless the equipment is electrically isolated.

The clamping screws of all terminal block connectors, for field wiring, using M4 screws shall be tightened to a nominal torque of 1.3 Nm.

Equipment intended for rack or panel mounting is for use on a flat surface of a Type 1 enclosure, as defined by Underwriters Laboratories (UL).

Any disassembly of the equipment may expose parts at hazardous voltage, also electronic parts may be damaged if suitable electrostatic voltage discharge (ESD) precautions are not taken.

If there is unlocked access to the rear of the equipment, care should be taken by all personnel to avoid electric shock or energy hazards.

Voltage and current connections shall be made using insulated crimp terminations to ensure that terminal block insulation requirements are maintained for safety.

Watchdog (self-monitoring) contacts are provided in numerical relays to indicate the health of the device. Schneider Electric strongly recommends that these contacts are hardwired into the substation's automation system, for alarm purposes.


To ensure that wires are correctly terminated the correct crimp terminal and tool for the wire size should be used.

The equipment must be connected in accordance with the appropriate connection diagram.

Protection Class I Equipment

- Before energizing the equipment it must be earthed using the protective conductor terminal, if provided, or the appropriate termination of the supply plug in the case of plug connected equipment.

- The protective conductor (earth) connection must not be removed since the protection against electric shock provided by the equipment would be lost.

- When the protective (earth) conductor terminal (PCT) is also used to terminate cable screens, etc., it is essential that the integrity of the protective (earth) conductor is checked after the addition or removal of such functional earth connections. For M4 stud PCTs the integrity of the protective (earth) connections should be ensured by use of a locknut or similar.

The recommended minimum protective conductor (earth) wire size is 2.5 mm (3.3 mm for North America) unless otherwise stated in the technical data section of the equipment documentation, or otherwise required by local or country wiring regulations.

The protective conductor (earth) connection must be low-inductance and as short as possible.

All connections to the equipment must have a defined potential. Connections that are pre-wired, but not used, should preferably be grounded when binary inputs and output relays are isolated. When binary inputs and output relays are connected to common potential, the pre-wired but unused connections should be connected to the common potential of the grouped connections.

Before energizing the equipment, the following should be checked:

- Voltage rating/polarity (rating label/equipment documentation),

- CT circuit rating (rating label) and integrity of connections,

- Protective fuse rating,

- Integrity of the protective conductor (earth) connection (where applicable),

- Voltage and current rating of external wiring, applicable to the application.

Accidental touching of exposed terminals

If working in an area of restricted space, such as a cubicle, where there is a risk of electric shock due to accidental touching of terminals which do not comply with IP20 rating, then a suitable protective barrier should be provided.

Equipment use

If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.

Removal of the equipment front panel/cover

Removal of the equipment front panel/cover may expose hazardous live parts, which must not be touched until the electrical power is removed.


UL and CSA/CUL Listed or Recognized equipment

To maintain UL and CSA/CUL Listing/Recognized status for North America the equipment should be installed using UL or CSA Listed or Recognized parts for the following items: connection cables, protective fuses/fuseholders or circuit breakers, insulation crimp terminals and replacement internal battery, as specified in the equipment documentation.

For external protective fuses a UL or CSA Listed fuse shall be used. The Listed type shall be a Class J time delay fuse, with a maximum current rating of 15 A and a minimum d.c. rating of 250 Vd.c., for example type AJT15.

Where UL or CSA Listing of the equipment is not required, a high rupture capacity (HRC) fuse type with a maximum current rating of 16 Amps and a minimum d.c. rating of 250 Vd.c. may be used, for example Red Spot type NIT or TIA.

Equipment operating conditions

The equipment should be operated within the specified electrical and environmental limits.

Current transformer circuits

Do not open the secondary circuit of a live CT since the high voltage produced may be lethal to personnel and could damage insulation. Generally, for safety, the secondary of the line CT must be shorted before opening any connections to it.

For most equipment with ring-terminal connections, the threaded terminal block for current transformer termination has automatic CT shorting on removal of the module. Therefore external shorting of the CTs may not be required, the equipment documentation should be checked to see if this applies.

For equipment with pin-terminal connections, the threaded terminal block for current transformer termination does NOT have automatic CT shorting on removal of the module.

External resistors, including voltage dependent resistors (VDRs)

Where external resistors, including voltage dependent resistors (VDRs), are fitted to the equipment, these may present a risk of electric shock or burns, if touched.

Battery replacement

Where internal batteries are fitted they should be replaced with the recommended type and be installed with the correct polarity to avoid possible damage to the equipment, buildings and persons.

Insulation and dielectric strength testing

Insulation testing may leave capacitors charged up to a hazardous voltage. At the end of each part of the test, the voltage should be gradually reduced to zero, to discharge capacitors, before the test leads are disconnected.

Insertion of modules and pcb cards

Modules and PCB cards must not be inserted into or withdrawn from the equipment whilst it is energized, since this may result in damage.

Insertion and withdrawal of extender cards

Extender cards are available for some equipment. If an extender card is used, this should not be inserted or withdrawn from the equipment whilst it is energized. This is to avoid possible shock or damage hazards. Hazardous live voltages may be accessible on the extender card.


External test blocks and test plugs

Great care should be taken when using external test blocks and test plugs such as the MMLG, MMLB and MiCOM P990 types, hazardous voltages may be accessible when using these. *CT shorting links must be in place before the insertion or removal of MMLB test plugs, to avoid potentially lethal voltages.

*Note: When a MiCOM P992 Test Plug is inserted into the MiCOM P991 Test Block, the secondaries of the line CTs are automatically shorted, making them safe.

Fiber optic communication

Where fiber optic communication devices are fitted, these should not be viewed directly. Optical power meters should be used to determine the operation or signal level of the device.

Cleaning

The equipment may be cleaned using a lint free cloth dampened with clean water, when no connections are energized. Contact fingers of test plugs are normally protected by petroleum jelly, which should not be removed.

5. DECOMMISSIONING AND DISPOSAL

De-commissioning The supply input (auxiliary) for the equipment may include capacitors across the supply or to earth. To avoid electric shock or energy hazards, after completely isolating the supplies to the equipment (both poles of any dc supply), the capacitors should be safely discharged via the external terminals prior to de-commissioning.

Disposal

It is recommended that incineration and disposal to water courses is avoided. The equipment should be disposed of in a safe manner. Any equipment containing batteries should have them removed before disposal, taking precautions to avoid short circuits. Particular regulations within the country of operation, may apply to the disposal of the equipment.


6. TECHNICAL SPECIFICATIONS FOR SAFETY Unless otherwise stated in the equipment technical manual, the following data is applicable.

6.1 Protective fuse rating The recommended maximum rating of the external protective fuse for equipments is 16A, high rupture capacity (HRC) Red Spot type NIT, or TIA, or equivalent. Unless otherwise stated in equipment technical manual, the following data is applicable. The protective fuse should be located as close to the unit as possible.

CAUTION - CTs must NOT be fused since open circuiting them may produce lethal hazardous voltages.

6.2 Protective Class

IEC 60255-27: 2005

EN 60255-27: 2006

Class I (unless otherwise specified in the equipment documentation). This equipment requires a protective conductor (earth) connection to ensure user safety.

6.3 Installation Category

IEC 60255-27: 2005

EN 60255-27: 2006

Installation Category III (Overvoltage Category III):

Distribution level, fixed installation.

Equipment in this category is qualification tested at 5 kV peak, 1.2/50 s, 500 , 0.5 J, between all supply circuits and earth and also between independent circuits.

6.4 Environment

The equipment is intended for indoor installation and use only. If it is required for use in an outdoor environment then it must be mounted in a specific cabinet or housing which will enable it to meet the requirements of IEC 60529 with the classification of degree of protection IP54 (dust and splashing water protected).

Pollution Degree - Pollution Degree 2 Compliance is demonstrated by reference Altitude - Operation up to 2000m to safety standards.

IEC 60255-27:2005

EN 60255-27: 2006

Introduction P44x/EN IT/I95 MiCOM P441, P442 & P444

IT

INTRODUCTION

Date: 2012 Hardware Suffix: J, K Software Version: C7.x, D4.x & D5.x, D6.x

Introduction P44x/EN IT/I95 MiCOM P441, P442 & P444 (IT) 1-1

IT

CONTENTS

1. INTRODUCTION TO MiCOM GUIDES 3

2. INTRODUCTION TO MiCOM 5

3. PRODUCT SCOPE 6

3.1 Ordering options 10

P44x/EN IT/I95 Introduction (IT) 1-2 MiCOM P441, P442 & P444

SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH


IT

1. INTRODUCTION TO MiCOM GUIDES The manual provides a functional and technical description of the MiCOM protection relay and a comprehensive set of instructions for the relays use and application.

The section contents are summarized below:

Safety Guide

P44x/EN IT Introduction

A guide to the MiCOM range of relays and the documentation structure. General safety aspects of handling Electronic Equipment is discussed with particular reference to relay safety symbols. Also a general functional overview of the relay and brief application summary is given.

P44x/EN TD Technical Data

Technical data including setting ranges, accuracy limits, recommended operating conditions, ratings and performance data. Compliance with norms and international standards is quoted where appropriate.

P44x/EN GS Getting Started

A guide to the different user interfaces of the protection relay describing how to start using it. This section provides detailed information regarding the communication interfaces of the relay, including a detailed description of how to access the settings database stored within the relay.

P44x/EN ST Settings

List of all relay settings, including ranges, step sizes and defaults, together with a brief explanation of each setting.

P44x/EN AP Application Notes

This section includes a description of common power system applications of the relay, calculation of suitable settings, some typical worked examples, and how to apply the settings to the relay.

P44x/EN PL Programmable Logic

Overview of the programmable scheme logic and a description of each logical node. This section includes the factory default (PSL) and an explanation of typical applications.

P44x/EN MR Measurements and Recording

Detailed description of the relays recording and measurements functions including the configuration of the event and disturbance recorder and measurement functions.

P44x/EN FD Firmware Design

Overview of the operation of the relays hardware and software. This section includes information on the self-checking features and diagnostics of the relay.

P44x/EN CM Commissioning

Instructions on how to commission the relay, comprising checks on the calibration and functionality of the relay.

P44x/EN MT Maintenance

A general maintenance policy for the relay is outlined.

P44x/EN TS Troubleshooting

Advice on how to recognize failure modes and the recommended course of action. Includes guidance on whom within Schneider Electric to contact for advice.


SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

P44x/EN SC SCADA Communications

This section provides an overview regarding the SCADA communication interfaces of the relay. Detailed protocol mappings, semantics, profiles and interoperability tables are not provided within this manual. Separate documents are available per protocol, available for download from our website.

P44x/EN SG Symbols and Glossary

List of common technical abbreviations found within the product documentation.

P44x/EN IN Installation

Recommendations on unpacking, handling, inspection and storage of the relay. A guide to the mechanical and electrical installation of the relay is provided, incorporating earthing recommendations. All external wiring connections to the relay are indicated.

P44x/EN CS Cyber security (Software Version C7.x only, hardware suffix K)

This section provides an overview about cyber security protection (to secure communication and equipment within substations environment). Cyber security standards and implementaion are decribed.

P44x/EN VH Firmware and Service Manual Version History

History of all hardware and software releases for the product.


IT

2. INTRODUCTION TO MiCOM MiCOM is a comprehensive solution capable of meeting all electricity supply requirements. It comprises a range of components, systems and services from Schneider Electric.

Central to the MiCOM concept is flexibility.

MiCOM provides the ability to define an application solution and, through extensive communication capabilities, to integrate it with your power supply control system.

The components within MiCOM are:

P range protection relays;

C range control products;

M range measurement products for accurate metering and monitoring;

S range versatile PC support and substation control packages.

MiCOM products include extensive facilities for recording information on the state and behaviour of the power system using disturbance and fault records. They can also provide measurements of the system at regular intervals to a control centre enabling remote monitoring and control to take place.

For up-to-date information on any MiCOM product, visit our website:

www.schneider-electric.com

http://www.schneider-electric.com/


SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

3. PRODUCT SCOPE MiCOM P441, P442 and P444 Numerical Full Scheme Distance Relays provide comprehensive distance protection for different applications like: lines, cables, tapped lines, lines with multiple zero sequence sources, non-homogeneous lines, series compensated lines and parallel lines.

The independently settable resistive reach for each zone allows easy application to short lines and cable protection. Using well-proven, patented techniques to directionalise, and making full use of digital memory, the relays can be applied in situations that can cause classic distance implementations to maloperate (crosscountry faults, close-up faults, etc.).

The MiCOM P441, P442 and P444 are in-built with a library of channel aided scheme logic, supplementary and back-up protection. It provides complete protection (4 alternative setting groups) to solidly earthed systems from distribution to transmission voltage levels.

Three phase tripping with faulted phase indication is provided for all protection functions. In addition models P442 and P444 allow single-phase tripping for the distance protection and the channel aided DEF protection (67N).

The P441, P442 and P444 distance relays equipped with 150MHz CPU and coprocessor board have been enhanced as described in the following table:


IT

Protection Functions Overview

ANSI IEC 61850 Features P441 P442 P444 21P PDIS Quadrilatral full scheme phase distance (6 zones) 21G PDIS Quadrilatral full scheme ground distance (6 zones) 50/51/67 OcpPTOC /

RDIR Directional / non-directional phase overcurrent (2 stages)

50N / 51N / 67N

EfdPTOC / RDIR

Directional / non-directional stand by earth fault (2 stages)

67N EfaPSCH Channel aided directional earth fault protection (DEF) 32N Directional zero sequence power protection 67/46 NgcPTOC /

RDIR Directional / non-directional negative sequence overcurrent

27 PTUV Undervoltage (4 stages, 1st stage DT and IDMT) 59 PTOV Overvoltage (4 stages, 1st stage DT and IDMT) 37 3-phase undercurrent (2 stages) 81U Underfrequency (4 stages) 81O Overfrequency (2 stages) 49 PTTR Thermal overload protection 50 / 27 PSOF Switch on to fault / trip on reclose (SOTF/TOR) 78 / 68 RPSB Power swing blocking & Out of step tripping (using PSL) 85 PSCH Channel aided schemes (PUP, POP, Blocking) Weak Infeed (WI) Echo logic Accelerated trip feature: Loss of Load - Zx extension 46BC Broken conductor (open jumper) 50ST OcpPTOC Stub bus protection 50BF RBRF Circuit breaker failure PTRC Tripping 3p 1/3p 1/3p 79 RREC Autoreclose (4 shots) 3p 1/3p 1/3p 25 RSYN Check synchronism option option optionVTS Voltage Transformer Supervision

(1, 2 & 3 phase fuse failure detection)

CTS Current Transformer Supervision CVTS Capacitive Voltage Transformer Supervision 51FF PTOC Emergency Overcurrent on VT failure OptGGIO Digital inputs 8 16 24 RlyGGIO Output relays (fast output optional) 14 21 32 or

46 SV IEC61850-9-2 sampled values Front communication port (RS232/K-bus) Rear communication port (RS485/Optic/Ethernet) * Second rear communication port (RS232/RS485/K-

Bus)* NA option option

Time synchronisation port (IRIG-B) * NA option option IEC 61850-9-2-LE Sampled Analogue values Ethernet

board NA NA option

* It may be possible to get all in one particular model. NA:Not applicable


SS

To complement the wide range of protection functions listed in the table, the P441, P442 and P444 relays are provided with the following measurement, control, monitoring, post fault analysis and self-diagnostic functions.

Fault locator

Display of instantaneous measured and derived values

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

Circuit breaker control, status & condition monitoring.

Trip circuit and coil supervision

4 alternative setting groups

Programmable scheme logic

Sequence of event recording

Comprehensive disturbance recording (waveform capture)

User configurable LEDs

Local and remote communication ports

Multiple communication protocol and interface options

Time synchronisation

Fully customisable menu texts

Multi level password protection

Test facilities

Power-up diagnostics and continuous self monitoring of the relay

User friendly setting and analysis software (MiCOM S1 Studio)

Application overview

FIGURE 1: FUNCTIONAL DIAGRAM


IT

Rating options

Auxiliary Voltage Rating options

Features P441 P442 P444 24 48 Vdc only 48 110 Vdc (30 100Vac) 110 250Vdc (100 240Vac)

In/Vn Rating boards options

Features P441 P442 P444 Dual rated CT (1&5A: 100-120V) Module Sum (1A / PXDB) IEC 61850-9-2-LE Sampled Analogue values Ethernet board

Communication protocol options

Communication protocol options

Features P441 P442 P444 K-Bus / Courier MODBUS VDEW (IEC 60870-5-103) (RS485 or Fibre Optic) DNP3.0 IEC 61850 + Courier via rear RS485 port IEC 61850 + IEC60870-5-103 via rear RS485 port DNP3.0 over Ethernet and Courier via rear K-Bus/RS485 IEC 61850-9-2-LE


SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

3.1 Ordering options

Relay Type (Distance protection 3 Pole tripping / reclosing with 8 inputs & 14 outputs)) P441

Auxiliary Voltage Rating 24 48V dc only 48 110V dc (30 100V ac) 110 250V dc (100 240V ac)

1 2 3

In/Vn RatingBoards Dual rated CT (1&5A: 100-120V) Module Sum (1A / PXDB)

1 5

Hardware options Standard version 1

Software options Without check synchronism With check synchronism

A B

Protocol Options K-Bus/Courier MODBUS VDEW (IEC 60870-5-103) (RS485 or Fibre Optic) DNP3.0

1 2 3 4

Mounting

Panel / flush Mounting M

Language English, French, German, Spanish English, French, German, Italian Chinese, English or French via HMI, with English or French only via Communications port

0 4

C

Software Version

Unless specified the latest version will be delivered * *

Settings File Standard version Customer Specific: other characters

8 --

Hardware Suffix

Original J


IT

Relay Type (Distance protection relay) P442 Auxiliary Voltage Rating 24 48V dc only 48 110V dc (30 100V ac) 110 250V dc (100 240V ac)

1 2 3

In/Vn RatingBoards Dual rated CT (1&5A: 100-120V) Module Sum (1A / PXDB)

1 5

Hardware options Nothing IRIG-B input Fibre Optic Converter only (IEC60870-5-103) IRIG-B input+ Fibre Optic Converter (IEC60870-5-103) Single Ethernet (100Mbps) only Rear Comms + InterMiCOM Rear comms + IRIG-B (modulated) + InterMiCOM Single Ethernet (100Mbps) + IRIG-B (modulated) Single Ethernet (100Mbps) + IRIG-B (demodulated) IRIG-B demodulated only InterMiCOM + Courier rear port InterMiCOM + Courier rear port + IRIG-B modulated

1 2 3 4 6 7 8 A B C D E

Redundant Ethernet (SHR) 2 multi-mode fibre ports + IRIG-B (modulated) Redundant Ethernet (SHR) 2 multi-mode fibre ports + IRIG-B (un-modul.) Redundant Ethernet (RSTP) 2 multi-mode fibre ports + IRIG-B (modulated)Redundant Ethernet (RSTP) 2 multi-mode fibre ports + IRIG-B (un-modul.) Redundant Ethernet (DHS) 2 multi-mode fibre ports + IRIG-B (modulated) Redundant Ethernet (DHS) 2 multi-mode fibre ports + IRIG-B (un-modul.)

G H J K L M

Product Specific 16 logic imputs & 21 Relay Outputs without check synchronism 16 logic imputs & 21 Relay Outputs with check synchronism 16 logic imputs & 18 Relay Outputs (4 high break) with check synchronism 16 logic imputs & 21 Relay Outputs (3 fast trip) with check synchronism 16 logic imputs & 21 Relay Outputs (6 fast trip) with check synchronism

A B CDE

Protocol Options K-Bus/Courier MODBUS VDEW (IEC 60870-5-103) (RS485 or Fibre Optic) DNP3.0 IEC 61850 + Courier via rear RS485 port IEC 61850 + IEC60870-5-103 via rear RS485 port DNP3.0 over Ethernet and Courier via rear K-Bus/RS485

1 2 3 4 6 7 8

Mounting

Panel / flush Mounting M


0 4

C

Software Version



8 --

Hardware Suffix

Original --I = Logic input(s), O=Relay outputs


SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

Relay Type (Distance protection relay) P444 Auxiliary Voltage Rating 24 48V dc only 48 110V dc (30 100V ac) 110 250V dc (100 240V ac)

1 2 3

In/Vn RatingBoards Dual rated CT (1&5A: 100-120V) IEC 61850-9-2-LE Sampled Analogue values Ethernet board Module Sum (1A / PXDB)

1 A 5

Hardware options Nothing IRIG-B input Fibre Optic Converter only (IEC60870-5-103) IRIG-B input+ Fibre Optic Converter (IEC60870-5-103) Single Ethernet (100Mbps) only Rear Comms + InterMiCOM Rear comms + IRIG-B (modulated) + InterMiCOM Single Ethernet (100Mbps) + IRIG-B (modulated) Single Ethernet (100Mbps) + IRIG-B (demodulated) IRIG-B demodulated only InterMiCOM + Courier rear port InterMiCOM + Courier rear port + IRIG-B modulated

1 2 3 4 6 7 8 A B C D E

Redundant Ethernet (SHR) 2 multi-mode fibre ports + IRIG-B (modulated) Redundant Ethernet (SHR) 2 multi-mode fibre ports + IRIG-B (un-modul.) Redundant Ethernet (RSTP) 2 multi-mode fibre ports + IRIG-B (modulated)Redundant Ethernet (RSTP) 2 multi-mode fibre ports + IRIG-B (un-modul.) Redundant Ethernet (DHS) 2 multi-mode fibre ports + IRIG-B (modulated) Redundant Ethernet (DHS) 2 multi-mode fibre ports + IRIG-B (un-modul.)

G H J K L M

Product Specific 1 & 3 Pole tripping/reclosing with 24I & 32O without check synchronism (C/S) 1 & 3 Pole tripping/reclosing with 24I & 32O with C/S 1 & 3 Pole tripping/reclosing with 24I & 34O (12 high break) with C/S 1 & 3 Pole tripping/reclosing with 24I & 32O with C/S+1 fast+standard trip PCB 1 & 3 Pole tripping/reclosing with 24I & 32O with C/S+2 fast+standard trip PCB 1 & 3 Pole tripping/reclosing with 24I & 46O without C/S 1 & 3 Pole tripping/reclosing with 24I & 46O with C/S 1 & 3 Pole tripping/reclosing with 24I & 46O with C/S+1 fast+standard trip PCB 1 & 3 Pole tripping/reclosing with 24I & 46O with C/S+2 fast+standard trip PCB

A B CDE HJ K L

Protocol Options K-Bus/Courier MODBUS VDEW (IEC 60870-5-103) (RS485 or Fibre Optic) DNP3.0 IEC 61850 + Courier via rear RS485 port IEC 61850 + IEC60870-5-103 via rear RS485 port DNP3.0 over Ethernet and Courier via rear K-Bus/RS485

1 2 3 4 6 7 8

Mounting Panel / flush Mounting Rack mounting

MN


0 4

C

Software Version



8 --

Hardware Suffix

Original --I = Logic input(s), O=Relay outputs

Technical Data P44x/EN TD/I95 MiCOM P441/P442 & P444

SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

TECHNICAL DATA


Technical Data P44x/EN TD/I95 MiCOM P441/P442 & P444 (TD) 2-1

SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

Technical Data P441, P442 & P444 Numerical Distance Protection: 3 Pole tripping/reclosing (P441) 1 & 3 Pole tripping/reclosing (P442 & P444)

In/Vn rating (ordering option): Dual rated CT (1&5A: 100-120V) Module sum (1A / PXDB) IEC 61850-9-2LE Sampled Analogue

Values Ethernet board (P444 only).

Input / Output (I/O) P441: 8I/14O P442 (with or without Check Synchronism): 16I/21O, 18I/18O (4 high break) 16I/21O (3 or 6 Fast Trip) P444 (with or without Check Synchronism): 24I/32O, 24I/46O, 24I/34O (12 high break).

Protocol options: K-Bus Modbus, VDEW (IEC 60870-5-103) DNP3.0 + (P442 and P444 only): IEC61850 + Courier via rear RS485 port IEC61850 + IEC 60870-5-103 via rear

RS485 port DNP3 over Ethernet with Courier rear port

K-Bus/RS485 protocol

Hardware options (P442 & P444): IRIG-B input Fibre optic converter (IEC60870-5-103) IRIG-B input and Fibre optic converter

(IEC60870-5-103) Single Ethernet 100Mbit/s Rear Comms + InterMiCOM Rear Comms + IRIB-B + InterMiCOM Single Ethernet (100Mbit/s) plus IRIG-B

(Modulated) Single Ethernet (100Mbit/s) plus IRIG-B

(De-modulated) IRIG-B (De-modulated) InterMiCOM + Courier Rear Port * InterMiCOM + Courier Rear Port + IRIG-B

modulated * Redundant Ethernet Self-Healing Ring, 2

multi-mode fibre ports + Modulated IRIG-B Redundant Ethernet Self-Healing Ring, 2

multi-mode fibre ports + Un-modulated IRIG-B

Redundant Ethernet RSTP, 2 multi-mode fibre ports + Modulated IRIG-B

Redundant Ethernet RSTP, 2 multi-mode fibre ports + Un-modulated IRIG-B

Redundant Ethernet Dual-Homing Star, 2 multi-mode fibre ports + Modulated IRIG-B

Redundant Ethernet Dual-Homing Star, 2 multi-mode fibre ports + Un-modulated IRIG-B

Mechanical Specification Design Modular MiCOM Px40 platform relay available in three different case sizes: P441 40TE (8), P442 60TE (12), P444 80TE (16). Mounting: front of panel flush mounting, rack mounted (19 ordering option).

Enclosure Protection Per IEC 60529: 1989 IP 52 Protection (front panel) against dust and dripping water, IP 50 Protection for the rear and sides of the case against dust, IP 10 Product safety protection for the rear due to live connections on the terminal block.

Weight 40TE: approx. 7.3kg 60TE: approx. 9.2kg 80TE: approx. 11.0kg

Terminals AC Current and Voltage Measuring Inputs Located on heavy duty (black) terminal block: Threaded M4 terminals, for ring lug connection. CT inputs have integral safety shorting, upon removal of the terminal block.

General Input/Output Terminals For power supply, opto inputs, output contacts and COM1 & optional COM2 rear communications. Located on general purpose (grey) blocks: Threaded M4 terminals, for ring lug connection.

Case Protective Earth Connection Rear stud connection, threaded M4. Must be earthed (grounded) using the protective (earth) conductor for safety, minimum earth wire size 2.5mm.

Front Port Serial PC Interface EIA RS232 DTE, 9 pin D-type female connector. Courier protocol for interface to MiCOM S1 Studio software. PEB* rated Maximum cable length 15m. Front Download/Monitor Port EIA RS232, 25 pin D-type female connector. For firmware downloads. PEB* rated circuit. Isolation to ELV level.

P44x/EN TD/I95 Technical Data (TD) 2-2 MiCOM P441/P442 & P444

SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

Rear Communications Port K-Bus/EIA(RS485) signal levels, two wire Connections located on general purpose block, M4 screw. For screened twisted pair cable, multidrop, 1000m max. SELV* rated circuit. Ethernet (copper & fibre)

Optional Rear IRIG-B Interface modulated or un-modulated BNC socket SELV* rated circuit. 50 ohms coaxial cable. Optional Rear Fiber Connection for SCADA/DCS BFOC 2.5-(ST)-interface for multi-mode glass fibre type 62.5, as per IEC874-10, 850nm short-haul fibers, one Tx and one Rx. Optical budget: 5.6 dB Data rate: 2.5 Mbits Max Length: 1000 m

Optional Rear Ethernet Connection for IEC 61850 10 Base T / 100 Base TX Communications Interface in accordance with IEEE802.3 and IEC61850 Isolation: 1.5kV. Connector type: RJ45 Cable type: Screened Twisted Pair (STP) Max. cable length: 100m 100 Base FX Interface Interface in accordance with IEEE802.3 and IEC61850 Wavelength: 1300nm Fiber: multi-mode 50/125m or 62.5/125m Connector style: BFOC 2.5 - (ST)

Optional Second Rear Communication Port EIA(RS)

232, 9 pin D-type female connector, socket SK4. Courier protocol: K-Bus, or EIA(RS)485 or EIA(RS)232. Maximum cable length: 15m. *: PEB = Protective equipotential bonded *: SELV = Safety/Separated extra low voltage Both PEB and SELV circuits are safe to touch after a single fault condition.

Optional Rear redundant Ethernet connection for IEC 61850 100 Base FX Interface Interface in accordance with IEEE802.3 and IEC61850 Wavelength: 1300nm Fiber: multi-mode 50/125m or 62.5/125m Connector style: BFOC 2.5 - (ST) Fiber defect connector (watchdog relay) Redundant Ethernet board Connector (3 terminals): 2NC contacts Rated voltage: 250 V Continuous current: 5 A Short duration current: 30 A for 3 s Breaking capacity

DC: 50 W resistive DC: 25 W resistive AC: 1500 VA resistive (cos = unity) AC: 1500 VA inductive (cos = unity)

Subject to maxima of 5 A and 250 V


SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

Ratings AC Measuring Inputs Nominal frequency: 50 and 60 Hz (settable) Operating range: 45 to 65Hz

AC Current Nominal current (In): 1 and 5 A dual rated (separate terminals

are provided for the 1A and 5A windings, with the neutral input of each winding sharing one terminal)

Nominal burden per phase 1 A:


SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

Output Contacts Standard Contacts General purpose relay outputs for signalling, tripping and alarming: Rated voltage: 300V Continuous current: 10A Short-duration current: 30A for 3s Making capacity: 250A for 30ms 10A continuous. Breaking capacity: DC: 50W resistive DC: 62.5W inductive (L/R = 50ms) AC: 2500VA resistive (cos = unity) AC: 2500VA inductive (cos = 0.7) Response to command: < 5ms Durability: Loaded contact: 10000 operations

minimum, Unloaded contact: 100000 operations

minimum.

Fast operation and High Break Contacts Dedicated purpose relay outputs for tripping: Uses IGBT technology Make and Carry: 30 Amps for 3 sec, 30A @ 250V resistive Carry: 250 Amps dc for 30ms Continuous Carry: 10 Amps dc Break Capacity: 10 Amps @ 250V resistive (10,000

operations) 10 Amps @ 250V L/R=40ms Operating time: 100M at 500Vdc (Using only electronic/brushless insulation tester).

Creepage Distances and Clearances Per IEC 60255-27: 2005 Pollution degree 3, overvoltage category III, impulse test voltage 5 kV.


SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

High Voltage (Dielectric) Withstand (EIA RS232 ports excepted). (i) Per IEC 60255-27: 2005, 2 kV rms, AC, 1 minute: Between all case terminals connected together and the case earth. Also, between all terminals of independent circuits. 1kV rms AC for 1 minute, across open

watchdog contacts and across open contacts of changeover output relays.

(ii) Per ANSI/IEEE C37.90-1989 (reaffirmed 1994): 1.5 kV rms AC for 1 minute, across open

contacts of changeover output relays.

Impulse Voltage Withstand Test Per IEC 60255-27: 2005 Front time: 1.2 s, Time to half-value: 50 s, Peak value: 5 kV, 0.5J Between all terminals, and all terminals and case earth. Electromagnetic Compatibility (EMC) 1 MHz Burst High Frequency Disturbance Test Per IEC 60255-22-1: 2008, Class III, Common-mode test voltage: 2.5 kV, Differential test voltage: 1.0 kV, Test duration: 2 s, Source impedance: 200 (EIA RS232 ports excepted).

100 kHz Damped oscillatory Test Per EN 61000-4-18: 2007, Level 3, Common-mode test voltage: 2.5 kV, Differential test voltage: 1.0 kV,

Immunity to Electrostatic Discharge Per IEC 60255-22-2: 1997, Class 4, 15kV discharge in air to user interface,

display, and exposed metalwork. Per IEC 60255-22-2: 1997, Class 3, 8kV discharge in air to all communication

ports. 6kV point contact discharge to any part of

the front of the product.

Electrical Fast Transient or Burst Requirements Per IEC 60255-22-4: 2002 and EN 61000-4-4: 2004. Test severity: Class III and IV: Amplitude: 2 kV, burst frequency 5kHz (Class III), Amplitude: 4 kV, burst frequency 2.5kHz (Class IV). Applied directly to auxiliary supply, and applied to all other inputs. (EIA RS232 ports excepted). Amplitude: 4 kV, burst frequency 5kHz (Class IV). Applied directly to auxiliary supply.

Fast transient disturbances on power supply (common mode only): 4 kV, 5 ns rise time, 50 ns decay time, 5 kHz repetition frequency, 15 ms burst, repeated every 300 ms for 1 min in each polarity, with a 50 source impedance Fast transient disturbances on I/O signal, data and control lines (common mode only): 4 kV, 5 ns rise time, 50 ns decay time, 5 kHz repetition frequency, 15 ms burst, repeated every 300 ms for 1 min in each polarity, with a 50 source impedance.

Surge Withstand Capability Per IEEE/ANSI C37.90.1: 2002: 4kV fast transient and 2.5kV oscillatory applied directly across each output contact, optically isolated input, and power supply circuit.

Surge Immunity Test (EIA RS232 ports excepted). Per IEC 61000-4-5: 2006 Level 4, Time to half-value: 1.2 / 50 s, Amplitude: 4kV between all groups and

case earth, Amplitude: 2kV between terminals of each

group.

Immunity to Radiated Electromagnetic Energy Per IEC 60255-22-3: 2000, Class III: Test field strength, frequency band 80 to 1000 MHz: 10 V/m, Test using AM: 1 kHz / 80%, Spot tests at 80, 160, 450, 900 MHz Per IEEE/ANSI C37.90.2: 2004: 25MHz to 1000MHz, zero and 100% square wave modulated. Field strength of 35V/m.

Radiated Immunity from Digital Communications Per EN61000-4-3: 2002, Level 4: Test field strength, frequency band 800 to 960 MHz, and 1.4 to 2.0 GHz: 30 V/m, Test using AM: 1 kHz / 80%.

Radiated Immunity from Digital Radio Telephones Per EN 61000-4-3: 2002 10 V/m, 900MHz and 1.89GHz.

Immunity to Conducted Disturbances Induced by Radio Frequency Fields Per IEC 61000-4-6: 1996, Level 3, Disturbing test voltage: 10 Vrms at 1kHz 80% am., 0.15 to 80MHz


SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

Power Frequency Magnetic Field Immunity Per IEC 61000-4-8: 2001, Level 5, 100A/m applied continuously, 1000A/m applied for 3s. Per IEC 61000-4-9: 2001, Level 5, 1000A/m applied in all planes. Per IEC 61000-4-10: 2001, Level 5, 100A/m applied in all planes at

100kHz/1MHz with a burst duration of 2s.

Conducted Emissions Per EN 55022: 1998: 0.15 0.5MHz, 79dBV (quasi peak)

66dBV (average) 0.5 30MHz, 73dBV (quasi peak)

60dBV (average).

Radiated Emissions Per EN 55022: 1998: 30 - 230MHz, 40dBV/m at 10m

measurement distance 230 1GHz, 47dBV/m at 10m

measurement distance.

EU Directives EMC Compliance Per 2004/108/EC: Compliance to the European Commission Directive on EMC is claimed via the Technical Construction File route. Product Specific Standards were used to establish conformity: EN50263: 2000

Product Safety Per 2006/95/EC: Compliance with European Commission Low Voltage Directive. Compliance is demonstrated by reference to generic safety standards: IEC 60255-27:2005

CE R&TTE compliance Radio and telecommunication terminal equipment (R&TTE) directive 99/5/EC. Compliance demonstrated by compliance to both the EMC directives on low voltage directive down to 0V. Applicable to rear communication ports.

Mechanical Robustness Vibration Test Per IEC 60255-21-1: 1996 Response Class 2 Endurance Class 2

Shock and Bump Per IEC 60255-21-2: 1995 Shock response Class 2 Shock withstand Class 1 Bump Class 1

Seismic Test Per IEC 60255-21-3: 1995 Class 2

Cyber Security (where applicable)

Implementation Following measures have been implemented: Four level access, Password strengthening, Disabling of unused application and

physical ports, Inactivity timer, Storage of security events, NERC-compliant default display.

Standards NERC CIP (North American Electric

Reliability Corporation Critical Infrastructure Protection, USA): CIP-002-1, CIP-003-1, CIP-004-1, CIP-005-1, CIP-006-1, CIP-007-1, CIP-008-1 and CIP-009-1

BDEW (Germany), ANSI ISA 99 (USA), IEEE 1686, IEC 62351, ISO/IEC 27002, NIST SP800-53 (National Institute of

Standards and Technology, USA), CPNI Guidelines (Centre for the Protection

of National Infrastructure, UK).

IEC 61850-9-2 Ethernet board (option) connexion RJ45 or optical fibre Antialiasing filter Number of logical nodes: up to 6 Time-delay at message

reception: 0 to 3ms Safety control:

- presence test alarm, - synchronization alarm, - quality alarm, independent per logical node


SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

Timing and Accuracy

PERFORMANCE DATA For all accuracies specified, the repeatibility is 5%, unless otherwise specified

DISTANCE PROTECTION All quoted operating times include the closure of the trip output contact.

50Hz Operation Minimum tripping time: 13ms (SIR = 5) 14ms (SIR = 30) Maximum tripping time: 18ms (SIR = 5) 21ms (SIR = 30) Typical tripping time: 17ms (SIR = 5) 17.5ms (SIR = 30) 100% of faults up to 75% of Zone 1 reach setting trip subcycle at SIR=5. 99% of faults up to 75% of Zone 1 reach setting trip subcycle at SIR=30.

60Hz Operation Minimum tripping time: 13ms (SIR = 5) 13ms (SIR = 30) Maximum tripping time: 16.5ms (SIR = 5) 18ms (SIR = 30) Typical tripping time: 14ms (SIR = 5) 16ms (SIR = 30) 100% of faults up to 75% of Zone 1 reach setting trip subcycle at SIR=5. 88% of faults up to 75% of Zone 1 reach setting trip subcycle at SIR=30.

Accuracy Characteristic shape, up to SIR = 30: 5% for on-angle fault (the set line angle) 10% for off-angle (Example: For a 70 degree set line angle, injection testing at 40 degrees would be referred to as off-angle). Zone time delay deviations:

20ms or 2%, whichever is greater

Sensitivity Settings < 5/In : (0.05In*5/(setting*In)) 5% Settings > 5/In : 0.05 In 5%

Distance elements Pick-up: Setting 5% Zone timer deviation:

20ms or 2%, whichever is greater Timer accuracy: 2ms Minimum trip level for IDMT elements:

1.05 Setting 5% Inverse time stages:

40ms or 5%, whichever is greater Definite time stages:

40ms or 2%, whichever is greater Repeatability: 5%

Sensitivity Settings < 5/In : (0.05In*5/(setting*In)) 5% Settings > 5/In : 0.05 In 5%

Transient Overreach: Additional tolerance due to increasing X/R ratios: 5% over the X/R ratio from 1 to 90 Breaker fail timers accuracy:


DIRECTIONAL AND NON-DIRECTIONAL OVERCURRENT (I>1, I>2, I>3 or I>4)

Accuracy DT Pick-up: Setting 5% IDMT Pick-up 1.05 Setting 5% DT reset: 0.95 Setting 2% IDMT reset: 0.95 Setting 5% Definite time stages:

20ms or 2%, whichever is greater Inverse time stages:


NEGATIVE SEQUENCE OVERCURRENT (I2>1, I2>2, I2>3 or I2>4)

Accuracy Zone 1: Pick-up: Setting 5% Reset: 0.95 Setting 5% Definite time stages:


BROKEN CONDUCTOR DETECTION

Accuracy (I2/I1) Pick-up: Setting 2.5% Reset: 0.95 Setting 2.5% Definite time stages:



SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

DIRECTIONAL AND NON-DIRECTIONAL EARTH FAULT PROTECTION (IN>1, IN>2, IN>3 or IN>4)

Accuracy DT Pick-up: Setting 5% IDMT Pick-up 1.05 Setting 5% Drop-off: 0.95 setting 5% Definite time stages:

20ms or 2%, whichever is greater DT reset: 0.95 Setting 2% Inverse time stages:

40ms or 5%, whichever is greater IDMT reset: 0.95 Setting 5%

AIDED DIRECTIONAL EARTH FAULT (D.E.F.) PROTECTION

Accuracy Zero Sequence Polarisation

pick-up: Setting 10% with relay characterist angle = 90

Negative Sequence Polarisation pick-up: Setting 5%

THERMAL OVERLOAD

Accuracy Thermal alarm pick-up: Calculated trip time 10% Thermal overload pick-up: Calculated trip time 10% Cooling time accuracy 15% of theoretical Repeatability: 1, VN>2)

Accuracy DT Pick-up: Setting 5% IDMT Pick-up: 1.05 x setting 5% Definite time operation: 20ms or 2%, whichever is greater Instantaneous operation:


SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

CURRENT TRANSFORMER SUPERVISION

Accuracy IN> Pick-up: Setting 5% VN< Pick-up: Setting 5% IN> Drop-off: 0.9 setting 5% VN< Drop-off:

(1.05 setting) 5% or 1V whichever is greater

Time delay operation: Setting 2% or 20ms whichever is greater

CTS block operation:


SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

FAULT AND DISTURBANCE RECORDS

Accuracy Time and date stamping: 2ms of applied fault/event Fault clearance time: 2% CB operating time: 5ms Protection operating time: 2% Waveshape: Comparable with applied quantities, 5% of applied quantities Trigger positions: 2% Record length: 8 records each of 1.8s duration

(1.5s at 60Hz)

FAULT LOCATOR

Accuracy Fault location: 2% of line length (under

reference conditions)* * Reference conditions solid fault applied on

line.

REFERENCE CONDITIONS Ambient temperature: 20C

FREQUENCY TRACKING RANGE 45 to 65Hz

BREAKER FAILURE Accuracy Reset time < 40ms 2% Thresholds: settings 5%

Ethernet data (where applicable) 10 Base T /100 Base TX Communications Interface in accordance with IEEE802.3 and IEC61850 Isolation 1.5kV Cable type: Screened twisted pair STP Max length: 100m

100 Base FX Interface Interface in accordance with IEEE802.3 and IEC61850 Wavelength: 1300nm Fibre: multi-mode 50/125m or 62.5/125m Connector style: ST

Transmitter Optical Characteristics (TA = 0C to 70C, VCC = 4.75 V to 5.25 V) BOL= Beginning of Life, EOL= End of Life

Parameter Sym Min. Typ. Max Unit Output Optical Power BOL 62.5/125 m, NA = 0.275 Fiber EOL

PO -19 -20 -16.8 -14 dBm avg.

Output Optical Power BOL 50/125 m, NA = 0.20 Fiber EOL

PO -22.5 -23.5 -20.3 -14 dBm avg.

Optical Extinction Ratio

10 -10

% dB

Output Optical Power at Logic 0 State

PO (0) -45 dBm avg.

BOL Beginning of life EOL End of life

Receive Optical Characteristics (TA = 0C to 70C, VCC = 4.75 V to 5.25 V)

Parameter Sym Min. Typ. Max. Unit Input Optical Power Minimum at Window Edge

PIN Min. (W)

-33.5 31 dBm avg.

Input Optical Power Minimum at Eye Center

PIN Min. (C)

-34.5 -31.8 Bm avg.

Input Optical Power Maximum

PIN Max. -14 -11.8 dBm avg.

InterMiCOM64 fiber optic teleprotection (where applicable) End-end operation: Table below shows bit transfer time (for multiplexed links, MUX denotes the multiplexer delay).

IM64 Cmd Applic. Typical Delay (ms)

Max (ms) Note

Direct fiber 3 to 7 9 No NoisePermissive Via MUX 5 to 8 + MUX

12 + MUX

BER 10-3

Direct fiber 4 to 8 10 No NoiseDir. Intertrip Via MUX 6 to 8 + MUX

13 + MUX

BER 10-3

BER Bit Error Rate for Channel


SS

IT

TD

GS

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

STZ1 (Impedance reach:) 0.001/In to 500/In (step 0.001/In )

SETTINGS, MEASUREMENTS AND RECORDS LIST

SETTINGS LIST

GLOBAL SETTINGS (SYSTEM DATA): Language:

English/French/German/Spanish/Italian/ Chinese (ordering option)

Frequency: 50/60Hz

CONFIGURATION Setting Group: Select via Menu Select via Opto Active Settings: Group 1/2/3/4 Setting Group 1: Disabled/Enabled Setting Group 2: Disabled/Enabled Setting Group 3: Disabled/Enabled Setting Group 4: Disabled/Enabled Distance Protection: Disabled/Enabled Power Swing: Disabled/Enabled Back-Up I>: Disabled/Enabled Negative Sequence overcurrent: Disabled/Enabled Broken Conductor: Disabled/Enabled Earth Fault overcurrent protection: Disabled/ Zero sequence power/ Earth fault overcurrent Aided Directional Earth Fault (DEF): Disabled/Enabled Voltage Protection: Disabled/Enabled Circuit Breaker Fail & I


SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

Zone Setting other parameters Serial Compensated Line: Enabled/Disabled Overlap Z mode: Enabled/Disabled Z1m Tilt Angle: 45 to +45 (step 1) Z1p Tilt Angle: 45 to +45 (step 1) Z2/Zp/Zq Tilt Angle 45 to +45 (step 1) Fwd Z Chgt Delay: 0 to 100ms (step 1ms) Volt. Memory Validity: 0 to 10s (step 10ms) Earth Current detection: 0 to 0.1I1 (step 0.01I1) Fault locator: KZm mutual Comp: 0 to 7 (step1) KZm Angle: 0 to 360 (step 1) Smart Zone 0 to 100 % (step 1%)

Busbar isolation modeBusbar status Enabled/Disabled : D6.x

Distance Scheme setting Program mode Standard or open scheme Standard Modes: Basic + Z1X, POP Z1, POP Z2, PUP Z2, PUP Forward, BOP Z1, BOP Z2. POP = Permissive Overreach Protection PUP = Permissive Underreach Protection BOP = Blocking Overreach Protection Fault type: Phase to Ground, Phase to Phase, Both enabled. Trip Mode: Force 3 Pole, 1 Pole Z1 and Carrier Received (CR), POP Z1 Z2 and CR. Signal sent from a zone to the relays setting (open scheme): CsZ1 (Carrier sent by Z1), CsZ2, CsZ4. Aided scheme on Carrier receipt Dist CR (open scheme): None, PermZ1: Permissive Z1 (Z1 can trip without

waiting the end of tZ1 timout), PermZ2, PermFwd (forward), Blocking Z1 (BlkZ1) (Z1 can only trip if a

Carrier is not received), BlkZ2. Additional time-delay for PUP Z2, PUP FWD, POP Z1 and POP Z2 schemes: 0 to 1s (stem 2ms) tReversal Guard: 0 to 0.15s (step 2ms)

Unblocking schemes (with permissive schemes): None, Loss of Guard mode, Loss of Carrier mode. TOR (Trip On Reclose)SOTF (Switch On To Fault) modes enabled or disabled for: TOR logic in case of fault in Z1, Z2, Z3 or

All Zones, SOTF logic in case of fault in Z1, Z2, Z3 or

All Zones, TOR or SOTF in Distance scheme, SOTF logic in case of fault Z1+Rev,

Z2+Rev or I>3 Enabled, SOTF initiated by level detectors, SOTF Delay: 10 to 3600s (step 1s) Z1X extension on channel fail: Enabled/Disabled

Weak Infeed Mode Status: Disabled/Echo/WI Trip & Echo/PAP Single Pole: Disabled/Enabled V< Threshold: 10 to 70V (step 5V) Trip time delay: 0 to 1s (step 2ms)

Loss of Load (LoL) Mode Status: Enabled/Disabled LoL on Channel failed: Enabled/Disabled I (%max) 10% to 100% (step 1%) I2> Status: Enabled/Disabled I2> (%max) 10% to 100% (step 1%) Imax line Status: Enabled/Disabled Imax line> (%max):

1In to 20In (step 0.01In) Delta I Status: Enabled/Disabled Unblocking time-delay: 0 to 30s (step 0.1s) Blocking zones: Z1/Z1X Block: Yes/No Z2 Block: Yes/No Zp Block: yes/No Zq Block: Yes/No Z3 Block: Yes/No Z4 Block Yes/No Out of Step (OOS): 1 to 255 (step 1) Stable swing: 1 to 255 (step 1)


SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

IEEE Moderately Inverse,

DIRECTIONAL AND NON DIRECTIONAL OVERCURRENT PROTECTION (Back-up I>) Directional and non directional I> protections: I>1, I>2 (range 0.0810In) Non directional I> protections: I>3, I>4 (range 0.0832In) I>1 Function / I>2 Function: Disabled, Definite Time (DT), IEC Standard inverse IEC Very inverse IEC Extremely inverse UK Long Time Inverse, IEEE Moderately Inverse, IEEE Very Inverse IEEE Extremely Inverse US Inverse US Short Time Inverse IN> (%max) 10% to 100% (step 1%) I>1 / I>2 Directional: Non-directional, Directional forward Directional reverse I>1 / I>2 VTS Block: Block/Non-directional I>1 / I>2 current set: 0.08In to 10.00In (step 0.01In) I>1 / I>2 Time-delay: 0 to 100s (step 0.01s) I>1 / I>2 Time-delay VTS: 0 to 100s (step 0.01s) I>1 / I>2 Time Multiplier Setting (TMS): 0.025 to 1.2 (step 0.005) I>1 / I>2 Time Dial: 0.5 to 15 (step 0.1) I>1 / I>2 Reset characteristics: DT or Inverse I>1 / I>2 tReset 0 to 100s (step 0.01s) I>3 Status / I>4 Status: Enabled/Disabled I>3 / I>4 current set: 0.08In to 32.00In (step 0.01In) I>3 / I>4 Time-delay: 0 to 100s (step 0.01s)

NEGATIVE SEQUENCE OVERCURRENT PROTECTION Directional and non directional I2> protections: I2>1, I2>2 (range 0.084In) Non directional I2> protections: I2>3, I2>4 (range 0.084In) I2>1 Function / I2>2 Function: Disabled, Definite Time (DT), IEC Standard inverse IEC Very inverse IEC Extremely inverse UK Long Time Inverse,

IEEE Very Inverse IEEE Extremely Inverse

US Inverse US Short Time Inverse IN> (%max) 10% to 100% (step 1%) I2>1 / I2>2 Directional: Non-directional, Directional forward Directional reverse I2>1 / I2>2 VTS Block: Block/Non-directional I2>1 / I2>2 current set: 0.08In to 4.00In (step 0.01In) I2>1 / I2>2 Time-delay:0 to 100s (step 0.01s) I2>1 / I2>2 Time VTS: 0 to 100s (step 0.01s) I2>1 / I2>2 TMS: 0.025 to 1.2 (step 0.005) I2>1 / I2>2 Time Dial: 0.01 to 100 (step 0.01) I2>1 / I2>2 Reset characteristics: DT or Inverse I2>1 / I2>2 tReset 0 to 100s (step 0.01s) I2>3 Status / I2>4 Status: Enabled/Disabled I2>3 / I2>4 Directional: Non-directional, Directional forward Directional reverse I2>3 / I2>4 VTS Block: Block/Non-directional I2>3 / I2>4 current set: 0.08In to 32.00In (step 0.01In) I2>3 / I2>4 Time-delay:0 to 100s (step 0.01s) I2>3 / I2>4 Time VTS: 0 to 100s (step 0.01s) I>2 Char angle 95 to +95 (step 1)

MAXIMUM OF RESIDUAL POWER ZERO SEQUENCE POWER Zero Sequence Power Status: Activated/Disabled K Time delay factor: 0 to 2 (step 0.2) Basis Time Delay: 0 to 10s (step 0.01s) Residual current: 0.05In to 1In (step 0.01In) P0 threshold: 0.3 to 6.0VA (step 30mVA)

BROKEN CONDUCTOR DETECTION Broken conductor: Enabled/Disabled I2/I1 setting: 0.2 to 1 (step 0.01) I2/I1Time Delay: 0 to 100s (step 1s) I2/I1 Trip: Enabled/Disabled


SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

DIRECTIONAL AND NON-DIRECTIONAL EARTH FAULT OVERCURRENT PROTECTION Earth Fault O/C Directional and non directional IN> protections: IN>1, IN>2 (range 0.0810In) Non directional IN> protections: IN>3, IN>4 (range 0.0832In) IN>1 Function / IN>2 Function: Disabled, Definite Time (DT), IEC Standard inverse IEC Very inverse IEC Extremely inverse UK Long Time Inverse, IEEE Moderately Inverse, IEEE Very Inverse IEEE Extremely Inverse US Inverse US Short Time Inverse IN> (%max) 10% to 100% (step 1%) IN>1 / IN>2 Directional: Non-directional, Directional forward Directional reverse IN>1 / IN>2 VTS Block: Block/Non-directional IN>1 / IN>2 current set: 0.08In to 10.00In (step 0.01In) IN>1 / IN>2 Time-delay:0 to 200s (step 0.01s) IN>1 / IN>2 Time VTS: 0 to 200s (step 0.01s) IN>1 / IN>2 TMS: 0.025 to 1.2 (step 0.005) IN>1 / IN>2 Time Dial: 0.5 to 15 (step 0.01) IN>1 / IN>2 Reset characteristics: DT or Inverse IN>1 / IN>2 tReset 0 to 100s (step 0.01s) IN>3 Status / IN>4 Status: Enabled/Disabled IN>3 / IN>4 Directional: Non-directional, Directional forward Directional reverse IN>3 / IN>4 VTS Block: Block/Non-directional IN>3 / IN>4 current set: 0.08In to 32.00In (step 0.01In) IN>3 / IN>4 Time-delay:0 to 200s (step 0.01s) IN>3 / IN>4 Time VTS: 0 to 200s (step 0.01s) IN> Directional IN2 Char angle 95 to +95 (step 1) Polarisation: Zero Sequence, Negative Sequence. IN> Blocking IN> Block Pole Dead Enabled/Disabled (C7.x and D6.x)

AIDED DIRECTIONAL EARTH FAULT (DEF) OVERVOLTAGE PROTECTION Aided DEF Status: Enabled/Disabled Polarisation: Zero Sequence, Negative Sequence. V> Voltage set: 0.5V to 20V (step 0.01V) IN Forward: 0.05In to 4In (step0.01In) Time delay: 0s to 10s (step 0.1s) Scheme logic: Shared/Blocking/Permissive Tripping: Three Phase/Single Phase Tp: 0 to 1000ms (step 2ms) IN Rev Factor: 0 to 1 (step 0.1)

THERMAL OVERLOAD Thermal characteristics: Disabled/Single/Dual Thermal trip: 0.08In to 3.2In (step 0.01In) Thermal alarm: 50% to 100% (step 1%) Time constant 1: 1 mn to 200mn (step 1mn) Time constant 2: 1 mn to 200mn (step 1mn)

RESIDUAL OVERVOLTAGE VN Type: Residual/HomopolarVN>1 function: Disabled/DT/IDMT VN>1 voltage set: 1V to 180V (step 1V) homopolar: 0.5V to 60V (step 0.5V)VN>1 Time delay: 0s to 100s (step 0.01s) VN>1 TMS: 0.5 to 100 (step 0.5) VN>1 tReset: 0 to 100s (step 0.5s) VN>2 Status: Enaled/Disabled VN>2 voltage set: 1V to 180V (step 1V) homopolar: 0.5V to 60V (step 0.5V)VN>2 Time delay: 0s to 100s (step 0.01s) (software version C7.x only)

UNDERCURRENT PROTECTION I< mode (threshold activation): I


SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

VOLTAGE PROTECTION V< & V> modes (threshold activation): V4 status: activated/deactivated Undervoltage V< Measurement mode: PhaseNeutrel, PhasePhase V3 or V>4 Time Delay: 0s to 100s (step 0.01s) *: C7.x and D6.x

FREQUENCY PROTECTION Underfrequency F


SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

CB CONTROL CB Control by: Disabled, Local, Remote, Local + Remote, Opto-input, Opto input + Local, Opto input + Remote, Opto input + Local + Remote. Close Pulse Time: 0.1s to 10s (step 0.01s) Trip Pulse Time: 0.1s to 5s (step 0.01s) Man Close Delay: 0.01s to 600s (step 0.01s) Healthy Window: 0.01s to 9999s (step 0.01s) Check Synchronizing (C/S) Window: 0.01s to 9999s (step 0.01s) A/R Single Pole: Enabled/Disabled A/R Three Pole: Enabled/Disabled

CT AND VT RATIOS Main VT ratios: 100V to 1MV (step 1V) Main VTs Secondary: 80V to 140V (step 1V) Check Synchronizing (C/S) VT: Primary: 100V to 1MV (step 1V) Secondary 80V to 140V (step 1V) Phase CT: Primary: 1A to 30kA (step 1A) Secondary 1A/5A Mutual Compensation CT: Primary: 1A to 30kA (step 1A) Secondary 1A/5A Check Synchronizing (C/S) input: A (phase A)N (Neutral)/ BB/CN/AB/BC/CA Main VT Location: Line/Bus CT polarity: Standard/Inverted

SEQUENCE OF EVENT RECORDER (RECORD CONTROL) Clear Events: Enabled/Disabled Clear Faults: Enabled/Disabled Clear Maint: Enabled/Disabled Alarm Event: Enabled/Disabled Relay O/P Event: Enabled/Disabled Opto Input Event: Enabled/Disabled System Event: Enabled/Disabled Fault Rec Event: Enabled/Disabled Maint Rec Event: Enabled/Disabled Protection Event: Enabled/Disabled DDB 31 0: (up to): DDB 2047 2016: Binary function link strings, selecting which

DDB signals will be stored as events, and which will be filtered out

MEASURED OPERATING DATA (MEASURE'T SETUP) Default Display: Description Plant reference, U I Freq, P Q, Date and Time. Local Values: Primary/Secondary Remote Values: Primary/Secondary Measurement Ref: VA/VB/VC/IA/IB/IC Measurement Mode: 0/1/2/3 Demand Interval: 199mn (step 1mn) Distance Unit: Miles/Kilometres Fault Location: Distance Ohms % of Line

COMMUNICATIONS COLUMN Courier protocol: Protocol indicated RP1 Address: 7 to 34 (step 1) RP1 Inactiv timer: 1mn to 30 mn (step 1mn) Physical link: RS485, Fibre optic RP1 Status RP1 Port configuration: Kbus/EIA(RS)485 RP1 comms mode: IEC60870 FT1.2 10-Bit no parity RP1 Baud Rate: 9600/19200/38400 bits/s IEC60870-5-103 protocol: Protocol indicated RP1 Address: 7 to 34 (step 1) RP1 Inactiv timer: 1mn to 30 mn (step 1mn) Baud Rate: 9600/19200/38400 bits/s Measurement period: 1 to 60s (step 1s) CS103 blocking: Disabled, Monitor blocking, Command blocking. RP1 Status RP1 Port configuration: Kbus/EIA(RS)485 RP1 comms mode: IEC60870 FT1.2 10-Bit no parity RP1 Baud Rate: 9600/19200/38400 bits/s Modbus protocol: Protocol indicated RP1 Address: 7 to 34 (step 1) RP1 Inactiv timer: 1mn to 30 mn (step 1mn) Baud Rate: 9600/19200/38400 bits/s Parity: Odd/Even/None Physical link: RS485/Fibre optic Date/Time Format: Enabled/Disabled RP1 Status RP1 Port configuration: Kbus/EIA(RS)485 RP1 comms mode: IEC60870 FT1.2 10-Bit no parity RP1 Baud Rate: 9600/19200/38400 bits/s


SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

RP2 Inactivity timer: 1 to 30mn (step 1mn)

DNP3.0 protocol: Protocol indicated RP1 Address: 7 to 34 (step 1) RP1 Inactiv timer: 1mn to 30 mn (step 1mn) Baud Rate: 9600/19200/38400 bits/s Parity: Odd/Even/None Measurement period: 1 to 60s (step 1s) Physical link: RS485/Fibre optic Time Synhronization: Enabled/Disabled RP1 Status RP1 Port configuration: Kbus/EIA(RS)485 RP1 comms mode: IEC60870 FT1.2/10-Bit no parity RP1 Baud Rate: 9600/19200/38400 bits/s Scale Value indicated Message Gap: 0 to 50ms (step 1ms) DNP Need Time: 1 to 30 (step 1) DNP Application fragment size: 100 to 2048 (step 1) DNP Application fragment timeout: 1s to 120s (step 1s) DNB SBO timeout: 1s to 10s (step 1s) DNP link timeout: 0 to 120s (step 1s) Ethernet port, IEC61850 protocol: Protocol indicated Protocol & Scale value indicated, Network Interface Card (NIC) protocol: Courier/IEC60870-5-103/Modbus/DNP3.0 NIC MAC Adress indicated, NIC tunnel timeout: 1 to 30mn (step 1mn) NIC Link Report: Alarm/Even/None Ethernet port, DNP3.0 protocol: Protocol, IP address, subnet mask, NIC MAC address and Gateway address indicated, DNP time synchro: Enabled/Disabled DNP Meas scaling: Primary/Secondary/Normalized RP1 Address: 7 to 34 (step 1) RP1 Inactiv timer: 1mn to 30 mn (step 1mn) Baud Rate: 9600/19200/38400 bits/s Parity: Odd/Even/None NIC tunnel timeout: 1 to 30mn (step 1mn) NIC Link Report: Alarm/Even/None SNTP parameters: Primary and Secondary SNTP addresses displayed SNTP poll rate: 64 to 1024s (step 1s) SNTP need time: 1 to 30mn (step 1mn) SNTP Application Fragment size: 100 to 2048 (step 1) SNTP Application fragment timeout: 1s to 120s (step 1s) SNTP SBO timeout: 1s to 10s (step 1s) Second rear port connection setting: Protocol and Status indicated RP2 Port configuration: Kbus/EIA(RS)485/EIA RS232 RP2 comms mode: IEC60870 FT1.2/10-Bit no parity RP2 Address: 0 to 255 (step 1)

RP2 Baud Rate: 9600/19200/38400 bits/s

COMMISSIONING TESTS Status of opto-isolated inputs indication, Status of output relays indication, Status of test port indication, Status of LEDs indication, Monitor Bit 1(up to 8): Binary function link strings, selecting which

DDB signals have their status visible in the Commissioning menu, for test purposes

Test Mode: Enabled or Disabled 87BB and 50BF trip blocked per zone Test Pattern: Configuration of which output contacts are to

be energized when the contact test is applied.

Contact test: No operation/Apply test/Remove test

LEDs test, Autoreclose test: No operation/ 3-pole test/ Pole A, B or C test Red or Green LED status visible, DDB31-0 to DDB 2047-2016 status visible.

OPTO CONFIGURATION Opto input voltage range: 24-27V 30-34V 48-54V 110-125V 220-250V Custom Opto Input 1 (up to # = max. opto no. fitted) Custom options allow independent thresholds to be set per opto, from the same range as above

HOTKEYS AND CONTROL INPUTS Control Inputs operation (CTRL inputs menu)menu: Status of control inputs indication, Control inputs operation: Set/Reset/No operation Control Inputs configuration (CTRL I/P config. Menu): The control inputs can be individually assigned to the hotkeys by stetting, Control input configuration: Latched/Pulsed Following text displayed in the hotkey menu can be set: Set/Reset / In/Out / Enabled/Disabled / On/Off Opto Input Labels (Opto I/P Labels menu) User defined text string to describe the function of the particular opto input.


SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

Logical Nodes: 4

Teleprotection (InterMiCOM comms) Source Address: 0 to 10 (step 1) Received Address: 0 to 10 (step 1) Baud rate: 600 Baud 1200 Baud 2400 Baud 4800 Baud 9600 Baud 19200 Baud Channels statistics: Visible/Invisible Nbr of tripping messages received Nbr blocking messages received, Number of messages received: tripping,

blocking, total and incorrect, Lost messages, Elapsed time, Reset statistics: Yes/No Channel diagnostics: Visible/Invisible Data carrier detect status, Frame synchronization status, Message status, Channel status, InterMiCOM hardware status. Loopback Mode: Internal/External/Disabled Configuration of which InterMiCOM signals

are to be energized when the loopback test is applied.

User defined test pattern, Loopback status

InterMiCOM configuration IM Msg Alarm Level: 0 to 100.0% (step 1%) InterMiCOM command Types: IM1, IM2, IM3 and IM4 Command types:

Disabled/Direct/Blocking IM5 Cmd Type:

Disabled/Permissive/Direct IM6, IM7 and IM8 Command types:

Disabled/Permissive/Direct Fallback mode:

Default/Latched Default value: 0/1 Frame Synchronization Time:

10ms to 1.50s (step 10ms)

Function keys 10 function keys: Status: Disabled/Locked/Unlocked Mode: toggled/Normal Label: User defined

Ethernet NCIT (MiCOM P444 relays with IEC61850-9-2 board only) Physical Link: Copper/Fibre optic AntiAlaising Filter: Enabled/Disabled Merge Unit Delay: 0 to 3ms (step 250s) Logical Nodes (LN) Arrangement:

VL,IL,IN / VL,IL,IN2 / VL,IL,IN,VB/ VL,IL,IN2,VB / VL,IL,IN2,IN,VB VL,Sum(2xIL) / VL,IL,IN,2xVB VL,IL,IN2,2xVB

IED configurator (IEC61850) MiCOM P442 & P444 only Switch between active or inactive configuration banks, MiCOM Configuration Language (MCL) files restoration. IEC 61850 configuration data displayed: Active / inactive Memory banks, Configuration revision number of Active or

inactive Memory bank, IP address, mask and Gateway conneced, SNTP: IP address of the primary and

secondary servers, IED name, IEC61850 GOOSE GOENA setting, test mode, Ignore test flag option

Supervision VT Supervision Time-delay: 1 to 20s (step: 1s) I2&I0 inhibition: 0 to 1A (step: 1mA) I> inhibition(D6.x): 0.08In to 32 In

(step: 0.01 In) 3P voltage detection: Enabled/Disabled Threshold 3P 10 to 70V (step 1V) CT Supervision Status: Enabled/Disabled VN< Inhibition:

0.5 to 22V (step 0.5V) or 2V to 88V (step 2V)

IN> setting 0.08In to 4In (step 0.01In) Time-delay: 0 to 10s (step 1s) CVT Supervision Status: Enabled/Disabled VN>: 0.5 to 22V (step 0.5V) Time-delay: 0 to 300s (step 0.01s)

Check Synchronization (system check menu Check Synchronism for autoreclosure or Manual CB closure: Live bus/dead line: Yes/No Dead bus /Live line: Yes/No Live bus / Live line: Yes/No V< Dead line: 5 to 30V (step 1V) V> Live line: 30 to 120V (step 1V) V< Dead bus: 5 to 30V (step 1V) V> live bus: 30 to 120V (step 1V) Differential voltage: 0.5V to 40V (step 0.1V) Diff. frequency: 0.02Hz to 1Hz (step 0.01Hz) Diff phase 5 to 90 (step 2.5) Bus-Line time-delay: 0.1s to 2s (step 0.1s)


SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

Autorecloser Autoreclose mode: Number of shots: 1P trip mode: 1, 1/3, 1/3/3 or 1/3/3/3 3P trip mode: 3, 3/3, 3/3/3 or 3/3/3/3 1P Dead time 1 0.1s to 5s (step 0.01s) 1P Dead time 1 0.1s to 60s (step 0.01s) Dead time 2 1s to 3600s (step 1s) Dead time 3 1s to 3600s (step 1s) Dead time 4 1s to 3600s (step 1s) Reclaim time: 1 to 600s (step 1s) Reclose time-delay: 0.1s to 10s (step 0.1s) Discrimination time: 0.1s to 5s (step 0.01s) A/R Inhibit window: 1s to 3600s (step 1s) C/S on 3P reclosure during Dead time 1: Enabled/Disabled Autoreclose lockout Autoreclose is blocked when user defined fault occurs: at T2, t2, Tzp or Tzq for Loss of Load Trip for I>1 or I>2 Trip for V4 Trip for IN>1, IN>2, IN>3 or IN>4 Trip for Aided D.E.F Trip for Zero Sequence Power Trip for PAP Trip (specific customer engineered

function) for Thermal Trip for I2>1, I2>2, I2>3 or I2>4 Trip for VN>1 or VN>2 Trip for I


SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

BLANK PAGE

Getting Started P44x/EN GS/I95 MiCOM P441/P442 & P444

SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

GETTING STARTED


Getting Started P44x/EN GS/I95 MiCOM P441/P442 & P444 (GS) 3-1

TD

SS

IT

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

CONTENTS

1. GETTING STARTED 3

1.1 User interfaces and menu structure 3 1.2 Introduction to the relay 3 1.2.1 Front panel 3 1.2.2 Relay rear panel 5 1.3 Relay connection and power-up 7 1.4 Introduction to the user interfaces and settings options 8 1.5 Menu structure 9 1.5.1 Protection settings 10 1.5.2 Disturbance recorder settings 10 1.5.3 Control and support settings 10 1.6 Password protection 11 1.7 Relay configuration 12 1.8 Front panel user interface (keypad and LCD) 13 1.8.1 Default display and menu time-out 14 1.8.2 Menu navigation and setting browsing 15 1.8.3 Hotkey menu navigation 16 1.8.4 Password entry 17 1.8.5 Reading and clearing of alarm messages and fault records 18 1.8.6 Setting changes 18 1.9 Front communication port user interface 19 1.10 MiCOM S1 Studio relay communications basics 20 1.10.1 PC requirements 20 1.10.2 Connecting to the P44x relay using MiCOM S1 Studio 21

2. P44X RELAY MENU MAP 29

P44x/EN GS/I95 Getting Started (GS) 3-2 MiCOM P441/P442 & P444

SS

IT

TD

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

BLANK PAGE

Getting Started P44x/EN GS/I95 MiCOM P441/P442 & P444 (GS) 3-3

SS

IT

TD

1. GETTING STARTED BEFORE CARRYING OUT ANY WORK ON THE EQUIPMENT, THE USER

SHOULD BE FAMILIAR WITH THE CONTENTS OF THE SAFETY SECTION/SAFETY GUIDE SFTY/4LM/E11 OR LATER ISSUE, THE TECHNICAL DATA SECTION AND THE RATINGS ON THE EQUIPMENT RATING LABEL.

1.1 User interfaces and menu structure

The settings and functions of the MiCOM protection relay can be accessed both from the front panel keypad and LCD, and via the front and rear communication ports. Information on each of these methods is given in this section to describe how to get started using the relay.

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

1.2 Introduction to the relay

1.2.1 Front panel

The front panel of the relay is shown in the following figures, with the hinged covers at the top and bottom of the relay shown open. Extra physical protection for the front panel can be provided by an optional transparent front cover. With the cover in place read only access to the user interface is possible. Removal of the cover does not compromise the environmental withstand capability of the product, but allows access to the relay settings. When full access to the relay keypad is required, to edit the settings, the transparent cover can be unclipped and removed when the top and bottom covers are open. If the lower cover is secured with a wire seal, this will need to be removed. Using the side flanges of the transparent cover, pull the bottom edge away from the relay front panel until it is clear of the seal tab.

The cover can then be moved vertically down to release the two fixing lugs from their recesses in the front panel.

!"

#

#$ ! %&

'$

(

)*$

FIGURE 1 - MiCOM P441 RELAY FRONT VIEW ARRANGEMENT (hardware J)

MiCOM P442 and P444 relay (hardware J) front views arrangements are equivallent to thnot represented in this technical manual.

P44x/EN GS/I95 Getting Started (GS) 3-4 MiCOM P441/P442 & P444

SS

IT

TD

User programmable

function LEDs (tricolor)

Serial No. Model

No. And Ratings

User programmable function

LEDs (tri-color)

Top cover HotkeysFixed

function LEDs

Bottom

cover

Function

Keypad

LCD

Battery compartment Front comms port Download/monitor port

P0103ENf

GS

ST

AP

PL

MR

FD

CM

MT

TS

SC

SG

IN

CS

VH

FIGURE 2 MICOM P442 & P444 RELAY FRONT VIEW (hardware K)

The front panel of the relay includes the following:

a 16-character by 2- or 3-line (alphanumeric liquid crystal display (LCD).

a keypad comprising 4 arrow keys ( , , and ), an enter key ( ), a clear key ( ), and a read key ( ) and two additive hotkeys.

12 LEDs; 4 fixed function LEDs on the left hand side of the front panel and 8 programmable function LEDs on the right hand side.

10 additional function keys plus 10 additional LEDs .

Hotkey functionality (figures 1 and 2):

SCROLL: Starts scrolling through the various default displays.

STOP: Stops scrolling the default display

for control of setting groups, control inputs and circuit breaker operation.

Function key functionality (figure 2):

The relay front panel, features control pushbutton switches with programmable LEDs that facilitate local control. Factory default settings associate specific relay functions with these 10 direct-action pushbuttons and LEDs e.g. Enable/Disable the auto-recloser function. Using programmable scheme logic, the user can readily change the default direct-action pushbutton functions and LED indications to fit specific control and operational needs.

Under the top hinged cover:

the relay serial number, and the relays current and voltage rating information*.

Under the bottom hinged cover:

battery compartment to hold the AA size battery which is used for memory back-up for the real time clock, event, fault and disturbance records.

a 9-pin female D-type front port for communication with a PC locally to the relay (distance of up to 15m) via an EIA(RS)232 serial data connection.

a 25-pin female D-type port providing internal signal monitoring and high speed local downloading of software and language text via a parallel data connection.

Getting Started P44x/EN GS/I95 MiCOM P441/P442 & P444

micom p441, p442 & p444

Documents