owner's manual - Škoda auto...preface this owner's manual is provided for the...
TRANSCRIPT
SIMPLY CLEVER
OWNER'S MANUALOWNER'S MANUAL
Infotainment Swing
5E0012720DG
Preface
This Owner's Manual is provided for the Infotainment Swing (hereinafter re-ferred to only as a device).
Please read this Owner's Manual carefully, because the operation in accord-ance with these instructions is a prerequisite for proper use of the unit.
5E
00
1272
0D
G
Table of Contents
Important information about this Owner'sManual 3
Explanations and further information 4
Abbreviations
Introductory information
Important notes 6
Unit overview 7
Device operation and settings
Device operation 8
Device settings 10
Radio
Operation 12
Settings 14
Media
Operation 15
Audio sources 17
Telephone
Introductory information 20
Pair and connect 21
Telephone functions 22
Vehicle systems
CAR - vehicle setting 26
Adjustment of the heating and coolingsystem 30
Index
2 Table of Contents
Important information about this Owner's Manual
This Owner's Manual is valid for the different versions of the InfotainmentSwing (hereinafter referred to only as device). The device may vary in both itsappearance and in the controls arrangement, depending on the vehicle modelin which it is installed.
This Owner's Manual describes all possible device functions without identify-ing them as special equipment, model variants or market-dependent equip-ment. Consequently, the device in your vehicle does not need to contain all ofthe functions described in this Owner's Manual.
For example, if the vehicle is not factory equipped with the sound system, themenu points ŠKODA Surround and Virtual Subwoofer are not displayed in the soundsettings menu.
For information about the device, e.g. with respect to its compatibility withexternal devices or the software update, please refer to the following web-sites.
http://go.skoda.eu/infotainment
The availability of some features described in this Owner's Manual dependson the type of external devices (for example, telephone, music player, etc.).
The illustrations in this Owner's Manual are for illustrative purposes only. Theillustrations can differ in minor details from your vehicle; they are only inten-ded to provide general information.
ŠKODA AUTO pursues a policy of ongoing product and model developmentwith all vehicles. Changes in terms of supply scope are possible at any timewith regard to design, equipment and technology. The information provided inthis Owner's Manual corresponds to the information available at the time ofpublishing.
Therefore, legal claims cannot be made based on the technical data, illustra-tions and information contained in this Owner's Manual.
We recommend that the web pages that are referred to in this Owner's Man-ual are displayed using the classic view. If the web pages are displayed usingthe mobile view, they may not contain all necessary information.
Screen texts that appear in this Owner´s Manual may differ slightly dependingon the texts show on the device screen.
Declaration of conformityŠKODA AUTO hereby declares that the ŠKODA Infotainment systems meet thebasic requirements and additional provisions of the 1999/5/EC Directive withreference to radio equipment and telecommunications devices.
3Important information about this Owner's Manual
Explanations and further information
Structure of this Owner´s ManualThe Owner´s Manual is hierarchically divided into the following areas.
■ Main chapters (e.g. Introductory information) - the title of the main chapter isalways shown on the lower right side of the page■ Chapter (e.g. Equipment overview)
■ Module (for example, Switching the unit on/off)
Information searchWhen searching for information in the Owner´s Manual, we recommend usingthe Index at the end of the manual.
Text notes- Short press (e.g. a button) within 1 s
- Long press (e.g. a button) for more than 1 s
Text Symbols® Registered trademark
™ Registered trademark
→ Marker to the next operation step
The text symbol used for the right control dial
WARNINGTexts with this symbol draw attention to threats of a serious accident, in-jury or loss of life.
CAUTIONTexts with this symbol draw attention to the risk of vehicle damage or possibleinoperability of some systems.
NoteTexts with this symbol contain additional information.
“Press”“Hold”
4 Explanations and further information
Abbreviations
Abbreviation Definition
A2DPa Bluetooth® profile for the one-sided audio data transmis-sion
ACC Adaptive cruise control
AF Alternative frequencies for the current radio station
AM Identification of the radio-frequency range
TCS Traction Control of the drive wheels
AVRCPa Bluetooth® profile for the operation associated with thetransmission of audio data multimedia functions
BTBluetooth ® - wireless communication for reception andtransmission of voice and data information
CNG Compressed natural gas
DAB Digital radio reception
DRMa system for monitoring or restricting the use of digital me-dia content
ESC Electronic Stability Control
FM Identification of the radio-frequency range
ID3 tagan additional feature of a music file, which allows for the dis-play of artist, title, album name, etc.
mp3 compressed audio format
PIN personal identification number
PTY Type of broadcast program
RDSa system for the transmission of additional information forFM radio reception
SIM card a card for the identification of the mobile network operator
TP Identification of a traffic information station
USB MSCa software profile for transferring files between two devices(sometimes referred to as EMS)
VBR variable bit rate with files that have data compression
VIN Vehicle identification number
wma compressed audio format
5Abbreviations
Introductory information
Important notes
Introduction to the subject
WARNING■ Concentrate fully at all times on your driving! As the driver you are fullyresponsible for the operation of your vehicle.■ Use the device only so that you have the vehicle fully under control in anytraffic situation, for example, the telephone does not couple or connect,does not work with the contact list, etc. - risk of accident!
WARNING■ Adjust the volume to ensure that acoustic signals from outside the vehi-cle, e.g. sirens from emergency vehicles, can be heard at all times.■ High volumes can cause hearing damage.
WARNING■ Never leave a communication device, e.g. mobile phone, audio sources, inthe deployment area of an airbag, on a seat, on the dashboard or any an-other area, from which it can be thrown during a sudden braking manoeu-vre, an accident or a collision - risk of injury!■ Never connect or disconnect an external device while driving - risk of ac-cident!■ Always route the connection cable of the external device such that isdoes not restrict you when driving.
CAUTIONIn some countries, some unit features can no longer be selected when the ve-hicle is running faster than a certain speed. This is not a malfunction, but com-plies with the national legal regulations.
External devices and applications
The availability of some of the functions described in this Owner´s Manualdepends on the type of device to be connected and the applications installedin it.
Mobile phonesOn the following pages, check to see if the device is compatible with the selec-ted mobile phones.
http://go.skoda.eu/compatibility
Due to the large number of mobile phones as well as the ongoing develop-ment of these devices, ŠKODA AUTO cannot always ensure compatibility withthe device unconditionally. It is always recommended to physically check thefunction on the associated vehicle, including the ŠKODA Partners, beforehand.
Only those versions of the selected phones will be tested and supported whichoriginate from the official distribution network. The same also applies to theirfirmware and software.
The functions of the mobile phone to be tested may differ from the same typeof mobile phone depending on the specification for the respective country orthe specific service.
Mobile phones with the operating system and in the version available at thetime of these tests will be tested. In this regard, it could be the case that thefunctions of a mobile phone may differ with a different operating system ver-sion compared to the one used with the tested phone.
ŠKODA AUTO can accept no responsibility for the continuous changes made bythe mobile phone manufacturers and application vendors.
The function of some mobile applications may be affected by the quality of theInternet connection at the respective location.
ŠKODA AUTO does not accept any liability for any damage to the device or ve-hicle due to the use of incorrect or illegal applications or the improper or unau-thorized use of mobile phones.
6 Introductory information
Unit overview
Description of the device
The device may differ depending on the vehicle model, in which it is installedin both its appearance and in the arrangement of the controls.
Fig. 1 Illustrative device overview
Left control dial for switching the device on and off; volume adjustmentControl dial for calls and confirmations - Radio menu » page 12 - Media menu » page 15Depending on equipment fitted:▶ - Muting▶ - Telephone menu » page 20 - Unit settings » page 10 - Sound settings » page 10
1
2
3
4
5
Depending on equipment fitted:▶ - Setting the vehicle systems » page 26 (not applicable for Yeti)▶ - Activating/deactivating the Traffic Monitoring » page 14 (applies
to Yeti)Touchscreen » page 8SD card slot » page 17
Touch screen
The device is equipped with a touch screen that can be operated by light fin-ger pressure on the screen surface.
The brightness of the screen can be set → Screen → Brightness:.
CAUTION■ The screen can only be operated by a slight touch of a finger. If there is toomuch pressure there is a risk of damage to the screen!■ To protect the screen, you can use a suitable screen protector for touch padsthat does not affect its functionality.■ Dirt can be removed from the screen by using a soft cloth and, if necessary,methylated spirits.
Software update
Current information on the compatibility of external devices can be found onthe following ŠKODAInternet pages.
http://go.skoda.eu/infotainment
▶To display the software information, press the button, then tap on theSystem information function surface.
▶To start the software update, tap on the Update software function surface inthe displayed menu.
Turn device on/off
› To power on/off the device, press .
Automatic Power On of the deviceIf the device was not switched off using the controller prior to switching offthe Ignition, this automatically switches on after the ignition is switched on.
6
7
8
7Introductory information
Automatic Power Off of the deviceIf the vehicle key is pulled out of the ignition lock while the unit is switched on,the device will switch off automatically.
If the vehicle is fitted with the starter button, the device will switch off auto-matically after the engine is switched off and the door is opened.
With the ignition off, the device will automatically turn off after about 30 mi-nutes.
The device turns off automatically under certain circumstances. The device in-forms of this via a text message on the device display.
Adjusting the volume
Every change in volume is displayed on the screen.
› To increase the volume, turn the controller clockwise.› To reduce volume, turn the controller anticlockwise.› To mute, turn the controller to the left to 0.› or: press the button.
The following symbol appears in the display when the sound is muted .
If, at the time of muting, sound is played from the source in the media menu,then the playback is interrupted (pause)1).
CAUTION■ High volumes can cause sound resonance in the vehicle.■ When changing or connecting an audio source, this may cause suddenchanges in volume. Reduce the volume before changing or connecting an au-dio source.
Device operation and settings
Device operation
Operating principles
Fig. 2 Screen area / screen display
Description of the display » Fig. 2Status line with time and outdoor temperature information and other in-formationInformation and the operation of the current menuFunction surfaces of the current menuIdentification of the current menuReturn to the higher-level menu Open a sub menu of the menu item with the “pop-up window”Menu item with “Checkbox”▶ - Function is switched on▶ - Function is switched offScroll symbol - positioning and moving in the menu is possible by movingfingers on the scroll symbol up or down▶ Finger touch above the scroll symbol - changes to the next screen im-
age up▶ Finger touch below the scroll symbol - changes to the next screen down
A
B
C
D
E
F
G
H
1) Does not apply for AUX.
8 Device operation and settings
Function surfacesThe screen areas which confirm a function or a menu are called “function sur-faces”.▶White text - the surface is active and thus selectable▶Grey text - the surface is inactive and thus not selectable▶Green frame - currently selected surface
Selecting menu/menu item/function▶By tapping on the function surface or .▶Turning the knob .
Confirming menu/menu item/function▶By tapping on the function surface.▶Press the wheel .
Returning to higher-level menu▶By tapping on the function surface .▶By tapping on the screen outside of the “pop-up window”.▶By pressing the corresponding button next to the screen (e.g. in the menu
Media, by pressing the button).
Select the menu item / function value▶ - Selected menu item / function value▶ - Deselected menu item / function value
Set value▶By pressing the function surface with one of the following symbols , , , ,, .
▶By touching or moving your finger over the scale.▶Turning the knob .
NoteDepending on the equipment, the device can be operated with the operatinglever or via the buttons on the multifunction steering wheel. Additional infor-mation » Vehicle Owner´s Manual.
Alphanumeric with keyboard
Fig. 3 Example of the keyboard display
The alphanumeric keypad is used to enter characters.
Description of the alphanumeric keyboard » Fig. 3Input lineContext-dependent:▶ - Switch to capital letters▶ - Switch to special characters▶ - Switch to numbersContext-dependent:▶ - Switch to numbers▶ - Switch to Latin letters▶ - Switch to Cyrillic lettersContext-dependent:▶ - Confirmation of the entered character▶ - Display of searched entries (the number of searched entries is dis-
played in the function surface)Return to the higher-level menuErase the entered charactersBy holding the variants of each type are displayed.Exchange between the more keyboard languagesEnters a blankMove the cursor within the input line to the leftMove the cursor within the input line to the right
SearchWhile entering characters, a search is made for corresponding entries.
The entry such as a telephone contact to be searched for must be enteredalong with the special characters (diacritics).
A
B
C
D
9Device operation and settings
By tapping on the function surface a list of matching entries opens. If fewerthan 4 entries are found, a list of the found entries opens automatically.
Device settings
Configuration wizard
Fig. 4 Configuration wizard
The Configuration wizard is automatically displayed if there are at least twonon-selected menu items after turning on the device, or if a new user accountin personalisation is selected.
Disable the automatic display of the Configuration wizard by tapping the func-tion surface Don´t show again.
› For manual display, press the button, then tap the function surface Con-figuration wizard.
The Configuration wizard allows you to set the following menu items in se-quence.
Renaming the user account of personalisation » Vehicle - Owner´s Man-ualTime setting (not applicable for Yeti)Date setting (not applicable for Yeti)Storing the radio stations with the currently strongest reception signalin the first memory group of each individual broadcast areaPairing and connecting a phone to the device
The selected menu item is provided with the symbol.
Menu items which are not set can be set by tapping on the respective functionsurface in the A » Fig. 4 area.
Sound settings
› Press the button.
■ Volume - Volume settings■ Max. switch-on volume - Sets the maximum volume when the device is turned
on■ Announcements - Adjustment of traffic announcements volume (TP)■ Speed-dep. vol.adjust - volume increases as speed increases■ Entert. entertain. - Lowers the audio volume (e.g. radio volume) with activated
parking aid■ AUX volume: - Sets the volume for the device connected through AUX■ BT audio: - Volume setting of the device connected via Bluetooth ® audio
profile■ Balance - Fader - Sets the balance between left and right, front and rear■ Bass - Mid - Treble - setting the equalizer■ ŠKODA Surround - Switching the surround sound■ Virtual Subwoofer- Switching the virtual sub woofer■ Confirmation tone - switch on/off audible tone when touching the screen
Screen settings
› Press the button, then tap the function surface Screen.
■ Screen off (in 10 s) - activate/deactivate the automatic screen off function1)
■ Brightness: - Adjusts the brightness of the screen■ Confirmation tone - Switch on/off audible tone when touching the screen■ Show clock in stdby mode - Time and date displayed on the screen when the igni-
tion is switched on and the unit is switched off
Time and date settings
Does not apply to Yeti.
› Press the button, then tap the function surface Time and date.
■ Time: - Time settings■ Time format: - Set the time format
1) The unit turns the screen off when no touch screen is performed or none of the keys are pressed / rota-ted for more than 10 seconds.
10 Device operation and settings
■ Summer time - Switches the summer setting on/off■ Automatic summer time - switch on/off the automatic daylight savings time
change■ Date: - Date settings■ Date format: - Set the date format
Setting the device language
› Press the button, then tap the function surface Language.› Select the device language or tap the function surface Automatic to set the
MAXI DOT display matching language (applies to the Yeti).
Additional keypad language settings
› Press the button, then tap the function surface Add. keyboard languages.
In this menu, a keyboard language set can be added to allow the entering ofcharacters other than those in the currently selected language (function sur-face ).
Unit settings
Does not apply to Yeti.
› Press the button, then tap the function surface Units.
■ Distance: - Distance units■ Speed: - Speed units■ Temperature: - Temperature units■ Volume: - Volume units■ Consumption: - Fuel consumption units■ CNG consump.: - CNG consumption units■ Pressure: - Pressure units for tyre pressure
Safe removal of the data source
› Press the button, then tap the function surface Remove SD card safely / Re-move USB Safely.
The appropriate message concerning the safe removal of the source is dis-played in the screen.
Now the external source can be removed or separated.
Restore factory settings
› Press the button, then tap the function surface Factory settings.
In this menu individual settings or all settings can be restored at the sametime.
Bluetooth® settings
› Press the button, then tap the function surface Bluetooth.
■ Bluetooth - Switch on/off Bluetooth® function■ Visibility: - switch on/off the visibility of the Bluetooth® device for other devi-
ces■ Name - change the device name■ Paired devices - display the list of paired Bluetooth ® devices■ Find devices - searches for available devices■ BT audio (A2DP/AVRCP) - switch on/off the connection options for external audio
devices
System information
› Press the button, then tap the function surface System information.
■ Update software - update software (e.g. Bluetooth®) » page 7■ Bluetooth: ... - version number of the Bluetooth ® software■ Device part number: ... - Part number of the device■ Hardware: ... - Version of the hardware used■ Software: ... - Version of the software used
The information on available software updates is obtained from a ŠKODA Part-ner or from the following ŠKODA Internet pages.
http://go.skoda.eu/infotainment
11Device operation and settings
Radio
Operation
Introduction to the subject
The device allows analogue radio reception of FM and AM frequency ranges aswell as DAB digital radio reception.
CAUTION■ For vehicles with window antennas do not stick foil or metal coated stickersto the window as this can lead to interference.■ Car parks, tunnels, tall buildings or mountains can interfere with the radiosignal even causing it to fail completely.
Main menu
Fig. 5 Main menu
› To display the main menu, press the button.
Main menu » Fig. 5The selected radio station (description or frequency)Radio Text (AM, FM) / Description of the group (DAB)Preset station buttons for favourite channelsChoice of radio range (FM / AM / DAB)Choice of storage groups of the preferred station in the selected broad-casting ranges (e.g. FM1, FM2 or FM3)Changing the station
Manual / semi-automatic station searchRadio Text displayRadio main menu settings
A
B
C
D
Information symbol in the status lineSymbol Meaning
Traffic information station
Traffic information signals are not available or the selected sta-tion is not a traffic information station
Signal is not available (DAB)
RDS function is switched off (FM)
AF Alternative frequency is switched off (FM)
If the displayed station name continuously changes (dynamic text), then it ispossible to fix the current text by holding your finger on the device screen inthe station name area. The station name is shown in full by holding your fingerin the area of the station name again (FM).
Search for station and select frequency
Station search› Tap on the Radio function surface in the main menu.
Depending on the setting → Arrow buttons: will set an available station fromthe Stations list or a station of the current broadcast range on the Stationsbuttons.
Select frequency› Tap on the Radio function surface. It current frequency range appears in
the scale.› To set the desired frequency value, tap the function surface or at the
bottom of the screen or rotate the controller or use your finger to movethe scale.
The frequency selection is terminated by pressing the controller.
Scan through the stations one after the other (scan)The function scans through all the available stations in the current frequencyrange in succession, for a few seconds each.
› To start/finish the automatic play of the available stations, press the control-ler in the Radio main menu.
12 Radio
List of available stations
Fig. 6 Example of a list of available FM/DAB stations (hierarchical sorting)
› To display the list of available stations of the currently selected broadcastingarea, rotate the controller in the Radio main menu.
› To play, tap on the function surface of the desired station.› To filter the stations according to programme type (e.g. culture, music, sport
etc.) in the FM 1) and DAB2) station list, tap on the function surface » Fig. 6 -.
Information symbols
Station is stored under one of the preset station buttons
Currently played stations
Traffic information station
(e.g.) Type of programme being broadcast (FM and DAB)
(e.g.) Type the regional broadcast (FM)
Signal reception is not available (DAB)
Signal reception is not safe (DAB)
Update the list of stationsIn the FM area, the station list is updated automatically.
In the AM and DAB area, a manual update is carried out by tapping on thefunction surface » Fig. 6 - .
Sort the stations in the station listThe FM station list can be sorted depending on the settings of the menu item → Advanced settings → Sort stations:.
The AM station list is sorted according to the frequency of the received sta-tion.
The DAB station list can be sorted depending on the settings of the menu item → Kind of stat. list:.
Station buttons for your favourite stations
Each radio range includes 12 station buttons for saving preferred stations.These are each divided into three groups.
A station can be stored in the device memory in one of the following ways.
› To save a station on the main menu Radio, hold down the desired functionsurface C » Fig. 5 on page 12 until an acoustic signal sounds.
› To save a station in the station list, keep the function surface of the desiredstation held down, select the memory group, and then tap the desired sta-tion button.
If a station is saved on an already assigned station button, this station buttonwill be overwritten.
Station logos
The station key of a preferred station can contain the name and the stationlogo.
Assign a station logo› Tap on the Radio function surface → Station logos.› Tap on an occupied station button and select the data carrier (SD card, USB).› Search for and select the desired station logo on the respective data carrier.
Remove station logo› Tap on the Radio function surface → Station logos.› Tap on the station button from which you want to remove a logo.› Or:: tap on the function surface All to delete the logos of all the station
buttons simultaneously.› Confirm / cancel the removal.
1) Applies with activated RDS function.2) Applies to selected global sorting of the station list.
13Radio
Note■ The following image formats are supported: jpg, gif, png, bmp (we recom-mend using the png format).■ Maximum resolution 400x240 pixels.
TP Traffic programme
› To switch on/off the traffic monitoring in the main menu Radio, tap on thefunction surface → Traffic program (TP).
During a traffic announcement, it is possible to cancel the current announce-ment if necessary by deactivating the traffic monitoring.
Note■ Should this station not transmit traffic reports or the signal is not available,then the device automatically searches in the background for another TP sta-tion.■ During playback in Media main menu or a station in the AM radio range, traf-fic news is received from the previously selected station in the FM radio range.
Settings
Settings
› Tap on the Radio main menu function surface.
■ Scan - auto-play all available stations in the current frequency band foraround five seconds each
■ Arrow buttons: - setting the function of the station change (function surfaces )■ Presets- Change between stations stored under the preset buttons■ Stations - Change between all available stations of the selected broadcast-
ing range■ Traffic program (TP) - Switches traffic programme on/off■ Radio text - Switching the text display radio (FM and DAB) on and off■ Kind of stat. list: - Sort types of radio stations in the station list (DAB)
■ Global - alphanumeric station sorting with the filtering ability according tothe transmitted program type
■ Hierarchical - station sorting according to their assigned parent stationgroups (Ensemble) - Tree structure of the list
■ Station logos - manual management of station logos■ Delete presets - Delete the stations stored under preset buttons■ Advanced settings - further settings that are different depending on the selec-
ted broadcasting range(FM and DAB)
Advanced Settings (FM)
› Select the FM band in the Radio main menu and tap on the function surface → Advanced settings.
■ RDS Regional: - Switch on/off the automatic tracking of related regional sta-tions■ Automatic - auto-selects the station with the best reception at the moment.
If you lose reception the region, the unit will automatically set anotheravailable region.
■ Fixed - Maintains the selected regional station continuously. When the sig-nal is lost, another regional station must be set manually.
■ Alternative frequency (AF) - Search for alternative frequencies of the station cur-rently being played to on/off
■ Radio Data System (RDS) - enable/disable RDS function (receiving additional in-formation from the station)1)
■ Sort stations: - Sort types of radio stations in the station list (FM)■ Group - Sort by transmitted program type■ ABC - alphabetical order according to station name
Advanced Settings (DAB)
› In the Radio main menu, select the DAB range and tap on the function sur-face → Advanced settings.
■ DAB traffic messages - Switch on/off DAB announcements■ Other DAB messages - Switch on/off other announcements (e.g., warnings, re-
gional weather, sports reports, financial news)■ DAB station tracking - Switch on/off automatic DAB station tracking on another
frequency or in other station groups■ Auto. DAB - FM switching - switches on/off auto-switching from DAB to the FM
frequency band if the DAB signal is lost
1) Only valid for some countries.
14 Radio
DAB station trackingWhen a DAB transmitter is a part of several broadcast stations and if the cur-rent station group is not available on any other frequency, then when the sig-nal is poor, the same station will be searched in another channel group.
Automatic change from DAB to FMWith bad DAB reception the device tries to find an FM transmitter.
The station name is followed by () while the station is being received on theFM band. The () marker disappears when the relevant DAB station can be re-ceived again.
If a DAB station is also not available in the FM band due to poor reception, thedevice will be switched to mute.
Media
Operation
Main menu
Fig. 7 Main menu
› To display the main menu, press the button.
Main menu » Fig. 7Information on playing trackPlayback timeline with a sliderSelect the audio sourceDepending on the audio source type:▶ Folder / Title list▶ Multimedia databaseSettings of the main menu Media
Note■ Information concerning the given title appears on the screen, if they are stor-ed as so-called ID3 Tag on the audio source. If no ID3 tag is available, only thetitle name is displayed.■ The remaining playback time indicated does not correspond to the actual re-maining playback time for titles with variable bitrates.
A
B
C
15Media
Select audio source
Fig. 8 Select the audio source
› In the Media main menu, tap on the function surface A » Fig. 8 and selectthe desired audio source.
› or: in the folder/track list and in the multimedia database hold down thefunction surface B and select the desired audio source.
By selecting an audio source, playback of titles available starts (not for AUX).
Use play
The unit will play the contents of the connected audio source according to thealphabetically sequenced directory and file name.
Operation Action
Play / Pause Tap
Play the previous titleTap (within 3 seconds after the
start of the track playback)
Plays the current track from the startTap (after about 3 seconds after
the start of the track playback)
Fast-reverse within the title Press and hold
Fast-forward within the title Press and hold
Play the next title Tap
Switch on/off the random playbackfrom the current album or folder
Tap
Operation Action
Switch on/off the repeat playbackfrom the current album or folder
Tap
Switch on/off repeat playback of spe-cific track
Tap
The movement within the track is possible by finger touching the timeline B» Fig. 7 on page 15.
Folder / track list
Fig. 9 Folder / Title list
› To display the folder / track list on the Media main menu, tap on the function surface.
The content of an audio source is displayed in alphabetical order in the fold-er/track list.
Folder/Title list » Fig. 9Selected audio source / audio source folder (movement within the folder iscarried out by pressing the function surface for the folder)Select the audio sourceFolderPlaylist
Currently playing title / track playback stoppedThe title cannot be played (tapping on the function surface shows thecause).
A
16 Media
Note■ With more than 1,000 tracks in the folder only the first 1,000 tracks with theoldest creation date are displayed.■ The scanning speed of the folder / track list depends on the connectionspeed and volume of data.
Multimedia database
Fig. 10 Multimedia database
For some Apple devices connected via USB, the multimedia database is dis-played instead of the folders and title lists.
In the multimedia database, the tracks are sorted according to individual cate-gories B » Fig. 10.
› To display the multimedia database, in the Media main menu tap on thefunction surface.
› To playback, select the category and then the title.
Multimedia database » Fig. 10Selected audio source / Selected category / folder of the audio sourceTap - selection of the parent folder / Hold - selection of the audio sourceSorting categories
Media settings
› Tap on the function surface in the Media main menu.
■ Mix/repeat inc. subfolders - Switch on/off the title display including subfolders■ Bluetooth - Settings for the Bluetooth® function■ Traffic program (TP) - Switches traffic programme on/off■ Activate AUX - Enables / disables the AUX input
A
B
■ Remove SD card safely - Safe removal of the inserted SD storage card■ Remove USB safely - safe removal of external devices connected to the USB in-
put
Audio sources
Introduction to the subject
› To play, first connect the desired audio source or insert it into the device andthen select the audio source from the list » page 16. Playback starts auto-matically (does not apply to AUX).
If AUX is selected as the audio source, the playback must be started on theconnected device.
CAUTION■ Do not save any important data or that which has not been backed up on theconnected audio sources. ŠKODA assumes no responsibility for lost or dam-aged files or connected audio sources.■ When changing or connecting an audio source, this may cause suddenchanges in volume. Reduce the volume before changing or connecting an au-dio source.
SD-card
Fig. 11 Insert the SD card
› Insert the SD card in the slot in the direction of arrow (with the cut end fac-ing right), until this “locks” » Fig. 11.
› To remove the SD card, tap on the Media main menu function surface →Remove SD card safely. Please wait... → SD can now be removed. appears on the screen.
› Press on the inserted SD memory card. The SD card “jumps” into the ejectposition.
17Media
CAUTION■ Do not use an SD card with a broken write protection slide - there is a risk ofdamage to the SD card reader!■ When using an SD card with an adapter, vehicle vibrations might cause thecard to fall out of the adapter.
USB input
The USB input (shown with the symbol ) is located in the front centre con-sole. The exact location of the input » Vehicle - Owner´s Manual.
The USB input audio source can be connected directly or via a connecting ca-ble.
› To connect, insert the USB audio source into the appropriate input.› To disconnect the USB audio source, tap on the Media main menu function
surface → Remove USB safely. Please wait... → USB device can be removed. appearson the screen.
› Disconnect the audio source from the corresponding USB input.
Charge USB audio sourceWith the ignition on after connecting the USB audio source, the charging proc-ess is automatically started (applies for audio sources where charging via theUSB connector is possible).
The charging efficiency can differ compared to the charging from the usualmains power supply.
Some connected audio sources may not be recognised and cannot be charged.
CAUTIONUSB extension cords, or reducers may impair the function of the connected au-dio source.
NoteWe recommend that you use extension cords from ŠKODA Original Accesso-ries.
Bluetooth®player
The unit allows audio files of a connected Bluetooth® player to play using theA2DP and AVRCP audio profile.
› To connect the Bluetooth® player with the device - follow the same instruc-tions as for pairing the device with a telephone» page 21.
› To disconnect the Bluetooth®player, end the connection in the list of paireddevices » page 22.
Apple deviceIf an Apple device is connected as a Bluetooth® player, and this is connected tothe USB input, then the Bluetooth ® connection is not dropped. If playback iscancelled, playback must be started again. Only if USB is selected as the audiosource will the Apple device disconnect as a Bluetooth® player. In this regard,an appropriate warning message appears on the device screen.
If an Apple device is connected to the USB input and playback is switched on,this device cannot be connected as a Bluetooth® player. In this regard, an ap-propriate warning message appears on the device screen.
AUX - input
The AUX input (marked with the lettering) is located in the front centreconsole. The exact location of the input » Vehicle - Owner´s Manual.
› To connect, insert the plug of the AUX audio source into the appropriate con-nector.
› To disconnect, pull the plug out of the AUX audio source.
CAUTION■ The AUX input must only be used for audio devices!■ If an external audio source is connected to the AUX input, which is equippedwith an adapter for external power supply, the sound may be impaired.
Note■ The 3.5 mm stereo jack plug is used for the AUX input.■ We recommend that you use extension cords from ŠKODA Original Accesso-ries.
18 Media
Supported audio sources and file formats
Supported audio sources
Source Interface Type Specification File system
SD card SD readerStandard
sizeSD, SDHC, SDXC
FAT16VFATFAT32exFAT
USB-devices
USB 1.x; 2.xand 3.x or
higher withsupport of
USB 2.x
MSC
USB stick;HDD (without any spe-
cial software);The MSC mode sup-ports USB devices
MTP
Devices with the An-droid operating system
or Windows mobile(mobile phone, tablet)
AppleDevices with the iOS
operating system(iPhone, iPod, iPad)
Bluetooth®
Player- -
Bluetooth proto-colsA2DPand AVRCP
(1.0 - 1.4)-
Supported audio file formats
Codec type(File formats)
File suffix Max bit rateMaximumsampling
ratePlaylists
Windows MediaAudio 9 and 10
wma 384 kbit / s 96 kHz m3uplswplasx
MPEG-1; 2 and 2.5(Layer-3)
mp3 320 kbit / s 48 kHz
Note■ The GPT standards (GUID partition table) method structured audio sourcesare not supported by the device.■ Files that are protected by Digital Rights Management (DRM) technologycannot be played back by the device.
19Media
Telephone
Introductory information
Introduction to the subject
This chapter covers the operation of a Bluetooth® device connected to the tel-ephone.
If a telephone is connected to the device with multiple SIM cards, then callscan be accepted by all SIM cards of the connected phone.
For outgoing calls, it depends on the type of connected telephone, either onlythe primary SIM card or one of the other SIM cards can be selected.
PhoneboxThe storage compartment in the front centre console can be equipped withthe Phonebox function » Vehicle - Owner´s Manual.
If a telephone is directed, with its rear side downwards, on the pad in the stor-age compartment, the phone signal is amplified by the roof antenna.
Telephones that support the Qi standard for wireless charging, can also becharged wirelessly in the storage compartment. At the start of the wirelesscharging, the appropriate message appears on the device screen.
WARNINGThe general binding country-specific regulations for operating mobilephones in the vehicle must be observed.
Telephone
Fig. 12 Main menu
› To display, press the button.
The Telephone main menu appears when a telephone is connected to the de-vice.
Home page - information and function surfaces » Fig. 12Name of the telephone service provider (with active roaming, the symbolappears before the name )Display the list of paired telephones (the name of the connected tele-phone appears in the function surface)Function surfaces of preferred contactsEmergency number dialling or function surface of the preferred contact» page 23, Manage preferred contacts (favourites)Select a group of function surfaces for preferred contactsEnter the telephone numberDisplay the telephone contact listDisplay the call list (missed calls, in addition to the function surface, thenumber of calls when absent is displayed)Menu settings for Telephone
Symbols in the status barSignal strength of the telephone service networkCharge status of the telephone batteryMissed callCurrent call
Settings
› In the main menu Telephone, tap on the function surface.
■ Hands-free - switch a call to the telephone / back to the device (the menu itemis displayed during a call)
■ Select telephone - Search for available telephones/list of paired telephones/se-lect telephone■ Find - search for available phones
■ Bluetooth - Bluetooth® settings » page 11■ User profile - user profile settings
■ Manage favourites - set the function surfaces for your favourite contacts■ Sort by: - Arrangement of telephone contact list
■ Surname - sort by contact name■ Name - sort by contact first name
■ Imp. contacts - Import telephone contacts■ Select ringtone - Selecting the ring tone
A
B
C
D
20 Telephone
■ Remember your mobile - Turn on/off the warning mode before forgetting thephone in the vehicle (if the phone was connected to the device)
■ Simultaneous calls - enable/disable the option to hold two concurrent calls
Pair and connect
Introduction to the subject
The range of the connection to the hands-free system is limited to the passen-ger compartment.
To pair a telephone with the device using Bluetooth®, it is necessary to pairthe two devices.
The pairing process is dependent on whether another telephone is connectedor not connected to the device at the time of pairing.
A telephone and a Bluetooth®player can be connected to the device. The tele-phone can also be a player at the same time.
Up to 20 external devices can be paired with the device. After reaching themaximum number, the pairing of the next external device will replace that ofthe device that has not been used for the longest period of time.
A connection with a telephone that is already paired does not require pairing.It is enough to find the telephone that has been paired in the list of pairedphones and make the connection.
WARNINGPair and connect a telephone to the device only when the vehicle is at astandstill - there is risk of accident!
conditions for pairing
The telephone can be paired with the device under the following conditions.
The ignition is switched on.The Bluetooth® function of the device and the telephone is switched on.The visibility of the device and the telephone is switched on.The telephone is within range of the Bluetooth® signal of the device.The telephone is compatible with the device.The telephone is connected to an external Bluetooth® device (e.g. “head-set”).
The pairing can be initiated from the device or from the telephone.
During the pairing and connection process, information messages are dis-played in the device screen and the telephone screen. These messages mustbe observed and if necessary confirmed (e.g. enabling the contact import orconnecting the Bluetooth® player among others).
Please refer to the compatibility of telephones as well as updates which areavailable for the Bluetooth® device, and are available on the ŠKODA Internetpages.
http://go.skoda.eu/infotainment
Pairing and connection process
Pair the telephone with the device› Search available Bluetooth® devices in your telephone.› Select the device (name of the device → Bluetooth → Name:).› Confirm or enter the PIN code to confirm the pairing.
The telephone is connected to the device or merely paired, depending onwhether one or no other external device is already connected.
Pair the device with the telephone› If there is no telephone connected to the device, then press the button
then tap the function surface Find telephone.› If a telephone is connected to the device, press the button, then tap on
the function surface → Find telephone.› Select the desired telephone from the list of selected external Bluetooth®
devices.› Confirm or enter the PIN code to confirm the pairing.
If external Bluetooth® devices are already connected to the device, then dur-ing the pairing and connection process messages and options for the possibleconnection type (e.g. replacement of the connected external Bluetooth® de-vice) are displayed.
21Telephone
Managing paired devices
Fig. 13 List of paired devices / Bluetooth ® profiles
› In the Telephone main menu, tap on the function surface → Bluetooth →Paired devices.
In the list of paired external devices, the following symbols of the Bluetooth ®
profile may appear for the individual external devices» Fig. 13 .
SymbolSymbolcolour
Operation
White External device can be connected as telephone
Green External device is connected as telephone
White
External device can be connected as Bluetooth® play-er
Green External device is connected as Bluetooth® player
Connection set-up▶Select the desired external device from the list of paired external devices.▶Select the desired profile from the list of available Bluetooth® profiles
» Fig. 13 - .
If external Bluetooth® devices are already connected to the device, then dur-ing the connection process messages and options for the possible connectiontype (e.g. replacement of the connected external Bluetooth® device) are dis-played.
Disconnection▶Select the desired external device from the list of paired external devices.▶Select the desired profile from the list of available Bluetooth® profiles
» Fig. 13 - .
Delete the paired external device▶To delete, tap on one of the following function surfaces.
- Delete all external devices- Delete the desired external device
▶Confirm the deletion by tapping on the function surface Delete.
NoteThe Bluetooth® audio profile can be switched on/off by pressing the but-ton and then tapping on the function surface → Bluetooth → BT-Audio(A2DP/AVRCP).
Telephone functions
Enter telephone number and select
Fig. 14 Numeric keypad / editing the telephone number
Enter a telephone number and dial› In the Telephone main menu, tap on the function surface.› Enter the telephone number using the numeric keypad » Fig. 14 - .› Select the number entered by tapping on the function surface .
Function surfaces of the numerical keyboardEnter the last dialled number / dial the telephone number enteredDialling the emergency number (valid only in certain countries)Dial the breakdown number in case of breakdownDial the info number (for information regarding the products and serv-ices of the brand ŠKODA )Selection of the mailbox number is not supported by the device
All
22 Telephone
Delete the last number enteredDisplay of function surfaces / for the movement of the cursor in theinput line » Fig. 14 -
Breakdown and info numbersThe breakdown and info numbers are free of charge. Charges are only madefor a telephone call in accordance with the fare conditions of your telephoneservice provider.
The phone numbers are already set at the factory. If you want to change thenumbers, then consult a ŠKODA service partner.
If no breakdown or Info calls can be made then a ŠKODA service partner shouldbe consulted.
Search for a contact using the numeric keypadThe numeric keypad can also be used for a contact search.
For example, if you enter 32, the unit will display contacts with the letter se-quence DA, FA, EB, etc. next to the numerical keypad in areas A » Fig. 14.
List of telephone contacts
Fig. 15 List of telephone contacts / contact details
› In the Telephone main menu, tap on the function surface, a list of tele-phone contacts is displayed » Fig. 15- .
Function surfacesContact searchSelect a number in the telephone contact list - if a telephone contact con-tains several telephone numbers, the system displays a menu containingthe telephone numbers for this contact after selecting the contact.Display the contact details » Fig. 15 -
A
B
Select the number in the contact detailsProcessing the telephone number of the contact before dialling
Import listAfter the first connection of your telephone with the device the import the tel-ephone contacts to the device memory starts. The import can take several mi-nutes.
The device telephone book contains 2000 memory locations for imported tele-phone contacts. Each contact can contain up to 5 telephone numbers.
The number of imported contacts can be viewed in the menu item → → User profile → Imp. contacts.
If an error occurs during the import, an appropriate message appears on thescreen.
Refresh listWhen the telephone reconnects with the device the list is automatically upda-ted.
The update can be performed manually as follows.
▶Press the button, then tap on the function surface → User profile →Imp. contacts.
During updating, the number of imported contacts to the device memory/thenumber of contacts in the telephone is displayed.
After updating the number of contacts imported / 2000 (maximum number ofcontacts imported) is displayed.
Manage preferred contacts (favourites)
Fig. 16 Favourite contacts
The function surfaces A » Fig. 16 allow an immediate selection of the prefer-red contact telephone number.
C
23Telephone
Function surface for emergency callThe function surface 4 in the first favourite group is configured by the fac-tory with the emergency number, but can be replaced by another contact.
To restore the emergency number, it is necessary to remove the telephonefrom the list of paired external devices » page 22 and then to pair and connectagain.
Assigning favourites› In the main menu Telephone, tap on the desired function surface A » Fig. 16.› Select the desired contact (if necessary one of the contact numbers).
Select a favourite groupThere are 2 groups available. Each group contains 4 function surfaces for pre-ferred contacts.
› Tap on the function surface and select the desired group.
Connecting to a favourite› Tap on the desired function surface A » Fig. 16.
Change allocated favourites› In the Telephone menu, hold the desired function surface A » Fig. 16.› Select the desired contact (if necessary one of the contact numbers).
Delete a favourite› Press the button, then tap on the function surface → User profile →
Manage favourites.› Press the desired function surface of the preferred contact and confirm the
deletion.
You can delete all contacts by tapping on the function surface All and con-firm the deletion.
Call list
Fig. 17 Call history / Contact details
› In the Telephone main menu, tap on the function surface, a call list is dis-played » Fig. 17 - .
Function surfaces and symbolsSetting the display depending on the type of call▶ All - List of all calls▶ Missed - List of missed calls▶ Dialled - List of dialled numbers▶ Received - List of received callsDial a number from the call listDisplay the contact details » Fig. 17 - Select the number in the contact detailsAnswered callOutgoing callMissed call
A
B
C
24 Telephone
Telephone conversation
Fig. 18 Incoming call / Current conversation
Fig. 19 Next incoming call / Call on hold
Depending on the conversation context, the following functions can be execu-ted.
End dialling / reject incoming call / end callAccept incoming call / return to held callSwitch on/off ringerHold a callSwitch off/on microphone
Switch on/off hands-free (call to the telephone / switch to device)▶To switch off the hands-free system, in the Telephone main menu, tap on
the function surface → Hands-free during a call.▶To switch off the hands-free system, tap on the function surface during a
call.
25Telephone
Vehicle systems
CAR - vehicle setting
Introduction to the subject
In the menu CAR travel data and information displayed on the vehicle andsome vehicle systems can be set.
Description of the individual systems » Vehicle Owner's Manual .
NoteSettings relating to the vehicle systems can only be made when the ignition isswitched on.
Main menu
Fig. 20 Function surfaces in the mainmenu
Function surfaces in the main menu » Fig. 20Selecting the following menu points▶ Driving data▶ DriveGreen▶ Convenience consumers▶ Veh. status
Operation of the media / radio playbackSet the auxiliary heater and ventilationVehicle system settings
Driving data
Fig. 21 Driving data
› Press the button, then tap on the function surface → Driving data.
Screen display » Fig. 21Distance travelledDriving timeAverage speedAverage fuel consumptionTransit point rating (DriveGreenFunction)Approximate range1)
Range (if the estimated range is less than 300 km, the vehicle starts to ap-proach the symbol)
Use the function surfaces to select one of the following presets.▶Since start - Driving data for the individual trip▶Long-term - Long-term driving data▶Since refuelling - Data since refuelling
DriveGreen
› Press the button, then tap on the function surface → DriveGreen.
DriveGreen - the driving efficiency is evaluated based on the information regard-ing the driving style.
A
B
C
D
E
F
G
1) For vehicles with CNG drive the approximate range with gasoline and CNG is displayed separately.
26 Vehicle systems
Convenience consumer
› Press the button, then tap on the function surface → Convenience con-sumer.
The screen displays up to three consumers that currently have the largestshare of fuel consumption (e.g. air conditioning or similar). A display also ap-pears which shows the fuel used for the operation of all convenience systems.
Vehicle condition
Fig. 22 Vehicle condition
› Press the button, then tap on the function surface → Veh. status.
In the screen, information regarding vehicle condition or function of the tyrepressure monitor is displayed.
› Using the function surfaces , select the menu item Veh. status.
Function surfaces and display » Fig. 22
A Vehicle representation (the zones of the vehicle are shown in differentcolours, corresponding to any warning messages that occur. The warn-ing messages are displayed once you touch the “vehicle”)
No message/warning messages relating to vehicle status and the num-ber (if there is only one message, one warning message text is dis-played)
Display information about the status of the START-STOP system
Personalisation - Display / change the user account
ESC and TCS systems
› Press the button, then tap on the function surface → ESC system:.
■ Active - activation on all components of the ESC system■ ASR off - Switch off the ASR system■ ESC Sport - activation of ESC Sport
Tyres
› Press the button, then tap on the function surface → Tyres.
■ Tyre Pressure Loss Indicator - Tyre pressure monitoring function■ SET - Storage of the tire pressure values
■ Winter tyres - Setting an alarm on reaching the speed limit for winter tyres■ Speed warning - Switching the function Winter tyres on and off■ Warning at - Sets the speed for the warning
Driver profiles (personalisation)
› Press the button, then tap on the function surface → Driver accounts.
Description of the personalisation settings » Vehicle - Owner's Manual.
Assistance systems
› Press the button, then tap on the function surface → Driver assistance.
■ ACC (cruise control) - Sets the adaptive cruise control■ Driving progr.: - Set the vehicle acceleration when adaptive cruise control is
activated1)
■ Eco - Economical■ Normal - Normal■ Sport - Sports
■ Last dialled selected - Switch on/off of the last distance selected■ Distance: - Set the distance monitoring to the vehicles ahead
■ Very close - Very small distance■ Close - Small distance■ Medium - Medium distance■ Far - Large distance■ Very far - Very large distance
1) On vehicles with the choice of travel mode, this setting is carried out » Vehicle - Owner's Manual, chap-ter Selection of travel mode.
27Vehicle systems
■ Front Assist - Sets the assistant for monitoring the distance to the vehiclesahead■ Active - Activate/deactivate the assistant■ Advance warning (Version 1) - Activate/deactivate advance warning■ Advance warning (Version 2) - Activating/deactivating and setting the distance
level at which a warning occurs■ Early - Longer distance■ Medium - Medium distance■ Late - Short distance■ Off - Deactivation of the warning
■ Display distance warning - Activate/deactivate distance warnings■ Lane Assist - Settings for Lane Assist
■ Active - Activate/deactivate the assistant■ Adaptive lane guidance - Activate/deactivate adaptive lane guidance
■ Blind Spot Monitor - Activation / deactivation of the assistant “Blind SpotMonitor”
■ Driver Alert System - Activate/deactivate the driver alert system■ Proactive pass. protection - Activate/deactivate proactive passenger protec-
tion
Parking and manoeuvring
› Press the button, then tap on the function surface → Parking and ma-noeuvring.
■ ParkPilot - Settings for the parking aid■ Activate automatically - Activate/deactivate the compact parking aid display
(when driving forward)■ Front volume - Adjust the volume of the beeps for obstacle detection in front■ Front tone setting - Setting the pitch of the beeps for obstacle detection in
front■ Rear volume - Set the volume level of the beeps for the rear obstacle detec-
tion■ Rear tone setting - Setting the pitch of the beeps for the rear obstacle detec-
tion■ Entert. entertain. - Lowers the audio volume (e.g. radio volume) with activated
parking aid■ Rear Traffic Alert - Activate/deactivate the Rear Traffic Alert
Light
› Press the button, then tap on the function surface → Light.
■ Background lighting - Sets the interior lighting■ Instrument panel - Sets the brightness of the instrument/switch lighting■ Footwell lighting - Sets the brightness of the footwell lighting
■ Light assistance - Setting of outdoor lighting■ Dynamic Light Assist - Activation/deactivation of the function Dynamic Light
Assist■ Light Assist - Activation / deactivation of the Light Assist function■ Switch-on time: - Sensitivity adjustment of the sensor for the automatic head-
light control■ Early - High sensibility■ Medium - Medium sensibility■ Late - Low sensibility
■ Aut. headlight contr. (rain) - Activate/deactivate automatic headlight control inrain
■ Comfort turn signal - Activate/deactivate lane change flashing■ Travel mode: - Light setting for the right/left-hand traffic
■ Left - For left-hand traffic■ Right - For right-hand traffic
■ Light Assist - headlight range control for the Halogen headlights■ “Coming/leaving home” - Setting the COMING HOME / LEAVING HOME-func-
tion■ Coming home - Set the period that the lights remain on after you leave the
vehicle (0 - 30 seconds; 0 = function deactivated)■ Leaving home - Sets the period that the lights remain on after you unlock the
vehicle (0 - 30 seconds; 0 = function deactivated)
Interior lighting (background lighting)
› Press the button, then tap on the function surface → Background light-ing.
■ Colour - Illumination colour selection■ Active - activate/deactivate the personalisation■ Colour - select the illumination colour
■ Areas - Brightness adjustment■ All - Brightness setting for all areas at the same time■ Instrument panel - Brightness setting for the control panel area■ Doors - Brightness setting for the door area■ Footwell lighting - Brightness setting for the footwell area
28 Vehicle systems
Mirror and wiper
› Press the button, then tap on the function surface → Mirrors and wipers.
■ Mirrors - Adjusts the mirrors■ Synchronous adjustment - Activate/deactivate synchronous mirror adjustment■ Lowering (reverse) - Activation / deactivation of the lowering of the front pas-
senger's mirror when reversing■ Fold in (when parked) - Activation / deactivation of the full collapse of the mir-
ror housing when the vehicle is locked■ Wipers - Adjusts the windscreen wipers
■ Automatic wiping (rain) - Activate/deactivate automatic windscreen wiping inrain
■ Automatic rear wiper - Activate/deactivate automatic rear window wiping
Open and close
› Press the button, then tap on the function surface → Opening and clos-ing.
■ Window operation - Window operation settings■ Conven. open.: - Set the convenience opening feature
■ All - All windows■ Driver - Driver's window only■ Off - Deactivates the convenience opening
■ Central locking - Settings for opening and closing of doors■ Door unlock.: - Set the door unlocking feature
■ All - All doors■ Single door - Driver's or passenger's door (when unlocking via the sensor in
the passenger door handle)■ Side - Doors on the driver or passenger side (when unlocking via the sen-
sor in the passenger door handle)■ Automatic locking - Activate/deactivate automatic locking when starting off■ “Easy Open” - activation/deactivation of the contactless opening of the boot
lid■ Auto. lugg. comp. cover - Enable / disable automatic reeling of the roll-up cargo
cover
Seats
› Press the button, then tap on the function surface → Seats.
■ Store seat position - Storage of the driver's seat and exterior mirror positionsin the remote control key when locking the vehicle■ Vehicle key activated - Activate/deactivate storing the driver's seat position
and exterior mirror position when locking the vehicle
Instrument cluster (multifunction display)
› Press the button, then tap on the function surface → Instrument cluster.
In this menu it is possible to hide/show the appearance of the menu items inthe instrument cluster multifunction display and reset the trip data.
■ Current consumption - Display of current fuel consumption on/off■ Average consumption - Display of average fuel consumption on/off■ Refuel quantity - Display of refuel quantity on/off■ Convenience consumers - Display of fuel consumption of convenience consumers
on/off■ Eco tips - Switch on/off the display for tips on saving fuel■ Travelling time - Display of travelling time on/off■ Distance - Display of distance travelled on/off■ Average speed - Display of average speed on/off■ Digital speed display - Display of current speed on/off■ Speed warning - Winter tyres warning on/off■ Oil temperature - Oil temperature on/off■ Reset "Since start" data - Reset the single-trip memory in the device screen and
in the display of the instrument cluster■ Reset "Long-term" data - Reset the long-term memory in the device screen and
in the display of the instrument cluster
Time, date and unit setting
› Press the button, then tap the function surface Time and date.
Description of the time and date settings » page 10.
› Press the button, then tap the function surface Units.
Description of unit settings » page 11.
Service
› Press the button, then tap on the function surface → Service.
29Vehicle systems
■ VIN: ... - Display of the vehicle identification number■ Inspection: in … or … days - number of km/days until the next inspection■ Oil change service: in ... or ... days - number of km/days until the next oil
change
Reset to factory settings
› Press the button, then tap on the function surface → Factory settings.
In this menu you have the possibility to reset the menu items in the settings ofthe vehicle systems to factory settings.
■ All settings■ All settings - Restoration of the settings all menu items
■ Individual settings■ Driver assistance - Restoration of the Driver assistance menus■ Parking and manoeuvring - Restoration of the Parking and manoeuvring menu items■ Light - Restoration of the Light menus■ Background lighting - Restoration of the Background lighting menu■ Mirrors and wipers - Restoration of the Mirrors and wipers menu■ Opening and closing - Restoration of the Opening and closing menu■ Instrument cluster - Restoration of the Instrument cluster menu■ Driver accounts - Restoration of the Personalisation menu
If one of the above menu items is selected, the system will ask you whetheryou really want to restore the settings.
■ Cancel - Return to higher-level menu■ Reset - Restore the settings
Adjustment of the heating and cooling system
Introduction to the subject
Applies to Superb and Octavia
In the display some of the settings for the Climatronic, the auxiliary heatingand ventilation can be made.
Description of the individual systems » Vehicle Owner's Manual .
NoteThe settings can only be made when the ignition is switched on.
Climatronic (automatic air conditioning)
Fig. 23 Climatronic - main menu
Call up the main menu› Press the button on the Climatronic control panel.
Function surfaces and display » Fig. 23
A Set the desired temperature (front - left side)
B Set the desired temperature (front - right side)
C Displays the current operation mode (or set the operation mode)of the Climatronic
D Setting the power in operationLight - low power, quiet operationMedium - basic powerStrong - high power
E Switching on/off and adjusting the fan speed, cooling system, airdistribution and the air recirculationa)b)
F Set the desired temperature (rear)a)
Colour representation of the air flow from the air vents at thefront(Blue colour - temperature reduction / red colour - temperature in-crease)
Lock / unlock the temperature setting using the rear controlsa)b)
Switch on/off the windscreen heatingb)
Switching on/off the Climatronic
Switch on / off the temperature synchronisation throughout theinterior of the vehicle according to the temperature setting on thedriver's sideb)
30 Vehicle systems
Set the auxiliary heater and ventilation
Climatronic settings
a) Applies for the Superb.b) When switched on, the symbol in the function surface is green.
Climatronic settingsPress the button, then tap on the function surface.■ Air-cond. profile: - Setting the power in operation
■ Light - Low power, quiet operation■ Medium - Base power■ High - High power
■ Automatic air recirculation - Automatic re-circulated air mode on/off■ Automatic auxiliary heater - Quick interior heating on/off■ Automatic windscreen heating - activates/deactivates the automatic windscreen
heating
NoteIf you do not operate the unit for longer than 10 seconds in the "Climatronic"menu and it was switched off before the menu was opened, the unit willswitch itself off.
Auxiliary heating and ventilation
Fig. 24 Auxiliary heater: Main menu/set preset time
Call up the main menu› Press the button on the Climatronic control panel, then tap on the func-
tion surface .
Or vehicles with manual air conditioning
› Press the button, then tap on the function surface .
Function surfaces and display » Fig. 24Departure time - Day and time when the vehicle is to be ready for useSetting the operating mode (heating / ventilation)List of pre-selected times, activation / deactivation of the preset timeSet the preset times 1 to 3 and the duration (10 - 60 minutes)When heating the windows are shown in red / with continuous aeration,the windows are shown in blueCurrently displayed preset timeActivation of the currently displayed preset timeSetting the departure time: Day, hour, minute
Only one preset time can be active. The activated preset time will be deactiva-ted again after it has started automatically. For the next start, activate one ofthe preset times.
The switched on system switches off on expiration of the operating durationor can be deactivated by pressing the icon for direct switch on/off or switchoff via radio remote control.
Note■ In the selection of the day in the preset time, there is an option betweenSunday and Monday without the specified day. If this setting is selected, thevehicle will be ready for use at the selected time, regardless of the current day.■ If a different time is set » page 10, Time and date settings, the activated pre-set time is automatically deactivated. The preset time must be reactivated.
A
B
C
D
E
F
G
H
31Vehicle systems
Index
A
ACC 27Additional keyboard languages 11Air conditioning 30Alphanumeric with keyboard 9AM 12Assistance systems 27Audio
Media 15Radio 12
Audio source 17Automatic air conditioning 30Automatic air recirculation 30Automatic cruise control 27Automatic driving light when raining 28Automatic locking 29Automatic rear window wiper 29Automatic turning off of the device 7Automatic wiping when raining 29AUX 18Auxiliary heating 31
B
Background lighting 28Blind spot monitoring 27Bluetooth
Settings 11Switch on/off 11Update 7Updates 11Visibility 11
Bluetooth Player 18Bluetooth profile 22Breakdown service 22Button CAR 26
C
Call listCall list 24
CAR 26Climatronic
Automatic mode 30Operating mode 30
Close 29Comfort turn signal 28COMING HOME 28Conditions for pairing 21Configuration wizard 10Convenience consumer 27Cooling system 30
D
DAB 12Settings 14
Date 10Description of the device 7Device
connect to the telephone 21Software update 7
Device language 11Device menu
CAR 26Media (Audio) 15Radio 12
Device MenuTelephone 20
Device operation 8Device screen 8
device screenkeyboard 9
Device screen 10Areas 8important information 7
Maintenance 7Operation 8
Digital radio receptionSettings 14
Disclaimer 6Door lock 29Door unlocking 29DriveGreen 26Driver Alert System 27Driver assistance 27Driver profiles 27driving abroad - light 28Driving data
Display 26Power on/off 29
Driving light when raining 28
E
Easy open 29Eco Tips - Multi-function display 29Emergency call 22ESC sport 27ESC system 27External devices 6
F
Factory settings 11, 30File formats 19
Prerequisites and restrictions 19FM 12
Settings 14Front Assist 27Function surfaces 8
H
Headlights - headlight range control 28Heated windscreen 30Heating 30, 31
32 Index
I
Important notes 6Import contacts 20Information service 22Input screen
Language characters 11Input screen with keyboard 9Inspection 29Instrument cluster 29Instrument lighting 28Interior - lighting 28Interior lighting 28Introductory information 6
K
Key - memory function 29keyboard 9
L
Lane Assist 27LEAVING HOME 28Light 28Light range 28Light sensor - switch-on of the lights 28List
Available stations 13Media 16of telephone contacts 23
List of paired devices 22Luggage compartment - open 29
M
Main beam 28Main menu
CAR 26Media 15Radio 12
Manage favourites 20Managing paired devices 22Manoeuvring 28Media 15
Audio source 17AUX 18Bluetooth Audio 18File formats 19Foreword 15List 16Main menu 15Multimedia database 17Operation 15Prerequisites and restrictions 19Safe removal of the data source 11SD-card 17Select audio source 16Settings 17Supported media 19USB 18Use play 16
Memory function of remote control key 29Menu
Device settings 8Set up 10
Menu CAR 26MFL
See Owner´s Manual 8Mirror
Fold in when parked 29Lower while reversing 29Synchronous adjustment 29
Mobile phone 6Multi-function display 29Multi-media
AUX 18Multifunction steering wheel
See Owner´s Manual 8Multimedia
USB 18
Multimedia databaseMedia 17
Mute 8
O
Open 29Operating lever
See Owner´s Manual 8Operation
Media 15Radio 12Telephone 20
P
Pairing process 21Parking 28Parking aid 28ParkPilot 28Personalisation 27
Configuration wizard 10Phonebox 20Play
Media 16Preferred contacts 23Principles of device operation 8Proactive occupant protection 27PTY filter 13
R
Radio 12DAB - settings 14FM - settings 14List of available stations 13Main menu 12Operation 12Preface 12Radio station Logo 13Save station 13Scan 12
33Index
Search for station 12Select frequency 12Settings 14Station buttons 13Traffic programme (TP) 14
Radio rangeSee main menu 12
Radio stationLogo 13Search for station 12Select station 12
Radio station logo 13Radio stations
Save station 13Station buttons 13
Rear Traffic Alert 28Rear window - automatic wiping 29Recirculation mode 30Reset - vehicle settings 30
S
Safe removal of the data source 11Save station 13Screen
see device screen 7Screen display 8SD-card 17SD card
Safe removal 11Seats
Setting 29Select radio range
See main menu 12Select radio station
See main menu 12Select source
Media 16Service 29
SettingsAdditional keyboard languages 11Bluetooth 11Configuration wizard 10DAB 14Device 10Device language 11Device screen 10FM 14Manage favourites 23Media 17Menus 8Radio 14Restore factory settings 11Software update 7Software updates 11Sound 10System information 7, 11Telephone 20Time and date 10Units 11User profile 23Vehicle 26Volume 8
Set up 10Software update 7Software updates 11Sound 10Speedlimit for winter tyres 27START-STOP 27Station logos
Update 7Stations
See main menu 12Status line 8
Telephone 20Switch telephone conversation
To the device 25to the telephone 25
Synchronous adjustment of both mirrors 29
System information 7, 11
T
TCS 27telephone
conditions for pairing 21Telephone 20
Bluetooth profile 22Breakdown service 22Call list 24connect to the device 21Dialling the telephone number 22Emergency call 22Enter telephone number 22Functions 22Import contacts 20Information service 22Main menu 20Manage favourites 20Operation 20pair 21Pairing process 21Phonebox 20Preferred contacts 23Settings 20Telephone 20Telephone book 23Telephone conversation 25User profile 20
Telephone book 23Telephone conversation 25Telephone functions 22Telephone number 22Time 10Touch screen 7Traffic programme (TP) 14Travel mode - light 28Turning off the device 7Turning on the device 7Tyre pressure values 27
34 Index
Tyres 27
U
Unit overview 7Units 11USB 18
Safe removal 11User account
Configuration wizard 10User profile 20
V
Vehicle - settings 26Vehicle condition 27Vehicle identification number 29Vehicle systems 26Ventilation 31VIN number 29Volume 8Volume setting 8
W
Warning messages 27Window - operation 29Window convenience operation 29Window operation 29Windscreen
Automatic wiping when raining 29Heating 30
Wiper 29
35Index
Reprinting, reproduction, translation, or any other use, either in whole or inpart, is not permitted without the written consent of ŠKODA AUTO a.s..
ŠKODA AUTO a.s. expressly reserves all rights relating to copyright laws.
Subject to change.
Issued by: ŠKODA AUTO a.s.
© ŠKODA AUTO a.s. 2016
www.skoda-auto.com
Swing: Fabia, Rapid, Rapid Spaceback, Yei, Octavia, Superbanglicky 05.2016S00.5614.39.205E0012720DG
5E0012720DG