pannello comandi thermo ebm thermo ebm control panel · 2020. 4. 16. · it - 5 - 2. descrizione...
TRANSCRIPT
Pannello comandi Thermo EBMThermo EBM control panel (Efficient Boiler Management)
Manuale istruzioniInstruction manual
Pannello comandi EBMManuale istruzioni
EBM control panelInstruction manual
IT
GB
pag. 4
pag. 70
cod. 35454020 - 06/2013
- 3 -
- 4 -
INDICE
1. Introduzione ................................................................................... pag. 05
2. Descrizione del pannello ............................................................... pag. 05
3. Conformità ....................................................................................... pag. 05
4. Dati tecnici ........................................................................................ pag. 05
5. Fornitura e Identificazione ................................................................ pag. 06
5.1 Accessori .................................................................................. pag. 06
6. Struttura ............................................................................................ pag. 06
7. Gestione funzioni .............................................................................. pag. 07
8. Montaggio/installazione .................................................................... pag. 07
9. Schema elettrico interno ................................................................... pag. 08
10. Legenda simboli/componenti schema elettrico ............................... pag. 09
11. Collegamenti al regolatore ............................................................... pag. 10
12. Collegamenti elettrici pannello-bruciatore ....................................... pag. 11
12.1 Pannello-bruciatore monostadio ............................................... pag. 11
12.2 Pannello-bruciatore bistadio ..................................................... pag. 11
12.3 Pannello-bruciatore modulante 3 punti ..................................... pag. 12
12.4 Pannello-bruciatore Modulante 3 punti FERROLI ..................... pag. 12
13. Gestione massima impianti .............................................................. pag. 13
14. Collegamento di generatori in cascata ............................................ pag. 14
15. Sonde ............................................................................................... pag. 15
16. Sonda esterna .................................................................................. pag. 15
17. Interfaccia AVS 37.294 ..................................................................... pag. 17
18. Impostazioni e programmazione ...................................................... pag. 21
18.1 Prima messa in servizio ............................................................. pag. 21
18.2 Scelta della lingua ..................................................................... pag. 21
18.3 Regolazione dell’ora e della data .............................................. pag. 22
19. Programmazione .............................................................................. pag. 23
19.1 Procedura di accesso ai menu e ai sottomenu ......................... pag. 23
19.2 Procedura di accesso ai sottomenu ......................................... pag. 23
20. Configurazione per la gestione del bruciatore ................................. pag. 24
20.1 Bruciatore modulante ................................................................ pag. 24
21. Configurazione dei limiti di funzionamento della caldaia ................ pag. 25
21.1 Regolazione limiti di funzionamento OEM della caldaia ........... pag. 25
22. Gestione circuiti riscaldamento ........................................................ pag. 25
22.1 Controllo valvola miscelatrice ................................................... pag. 26
22.2 Attivazione funzionamento senza unità ambiente digitale ........ pag. 26
23. Gestione acqua calda sanitaria (ACS) ............................................. pag. 27
23.1 Controllo della ricarica .............................................................. pag. 27
23.2 Carico accellerato dell'accumulatore ACS ............................... pag. 27
24. Curve climatiche - temperatura scorrevole ...................................... pag. 28
24.1 Adattamento curve climatiche .................................................. pag. 28
25. Anticondensa ................................................................................... pag. 29
25.1 Configurazione del ricircolo anticondensa ............................... pag. 29
26. Configurazione per la gestione di generatori in cascata ................. pag. 30
26.1 Cenni strategia gestione caldaie in cascata ............................. pag. 31
27. Mantenimento in temperatura della mandata ....................................... pag. 31
28. Configurazione per l'integrazione del solare termico ........................ pag. 32
28.1 Integrazione solare termico con un solo collettore .................... pag. 32
28.2 Integrazione solare termico con collettore e serbatoio separato .... pag. 33
28.3 Integrazione solare termico con due collettori ........................... pag. 33
28.4 Cenni sulle impostazioni di carico dell'accumulatore sanitario ...... pag. 34
28.5 Protezione antigelo collettore ..................................................... pag. 34
28.6 Protezione surriscaldamento collettore ...................................... pag. 34
29. Caldaia a combustibile solido ........................................................... pag. 35
29.1 Modalità di funzionamento ......................................................... pag. 35
29.2 Setpoint ...................................................................................... pag. 35
29.3 Controllo caldaia/bruciatore ....................................................... pag. 35
30. Visualizzazione gestione dei parametri ............................................. pag. 36
31. Codici di errore/guasto ...................................................................... pag. 51
31.1 Legenda codici .......................................................................... pag. 51
32. Esempi di schemi realizzabili (diagrammi e funzioni) ....................... pag. 53
32.1 Legenda schemi ........................................................................ pag. 53
32.2 Schemi ....................................................................................... pag. 54
IT
- 5 -
2. DESCRIZIONE DEL PANNELLOIl Pannello Comandi Thermo EBM è un regolatore climatico, dotato di sonda per la misura della temperatura esterna, per la gestione ed il controllo di installazioni
e sistemi complessi costituiti da una o più caldaie in cascata, impianti integrati con pannelli solari e a tipologie diverse di generatori di calore.
L’impiego della sonda esterna permette di generare solo il calore necessario in base alla richiesta evitando gli sprechi. Il Pannello può gestire, per la genera-
zione del calore, caldaie equipaggiate con bruciatori monostadio, bistadio e modulanti a tre punti o 0-10V e, per l’utilizzo del calore, due impianti miscelati, un
impianto diretto ed un bollitore per l’Acqua Calda Sanitaria (ACS).
3. CONFORMITÀ
4. DATI TECNICI
Il Pannello Thermo EBM è conforme a:
- Direttiva Bassa Tensione 2006/95/CE
- Direttiva Compatibilità elettromagnetica 2004/108/CEE
Alimentazione elettrica 230V - 50/60 Hz
Uscite di comando dei carichi 230V - 2A
Relè modulazione bruciatore 230V - 10A
Grado di protezione elettrica IP 20
Fusibile F 8A L 250V
Termostato sicurezza caldaia 110 (0/-6)°C
Assorbimento massimo 8A
1. INTRODUZIONEQuesto manuale integra i manuali degli apparecchi sui quali viene installato il Pannello Comandi Thermo EBM e deve quindi essere conservato con cura per
ogni ulteriore consultazione.
A tali manuali si rimanda per i Divieti e le Regole di sicurezza.
Il Pannello deve essere destinato all’uso previsto da Ferroli S.p.A. che non è responsabile per danni causati a persone, animali o cose, da errori d’installazione,
di regolazione, di manutenzione e da usi impropri.
ATTENZIONE
•L’installazionedelPannelloThermoEBMdeveessereeffettuatadapersonaleprofessionalmentequalificatoodaunServizioTecnicoAutorizzato
Ferroli in conformità alle Norme Tecniche e alla Legislazione, nazionale e locale, in vigore.
•Devonoessereosservate,inoltre,leindicazionisullasicurezza,l’installazione,lamanutenzioneel’usoriportateinquestomanuale.
DIVIETO
•ÈVIETATOfareeffettuareleregolazionidell’apparecchioaibambinioallepersoneinabilinonassistite.
- 6 -
5. FORNITURA E IDENTIFICAZIONE
6. STRUTTURA
Il Pannello Thermo EBM viene fornito in un imballo di cartone.
È identificabile:
- dall’etichetta con descrizione e codice a barre sull’imballo
- dalla Targetta Tecnica applicata all’involucro
Il Pannello Thermo EBM è composto da:
1-InterruttoreOn/Offcaldaia(SB1)esegnalazioneluminosaverde(HL1)
2 - Interruttore di consenso “start bruciatore” (SB2)
3 - Termostato Sicurezza Caldaia (TSC), a riarmo manuale, con pulsante di sblocco e segnalazione luminosa rossa (HL2)
4 - Interfaccia Utente AVS37.294
La confezione contiene inoltre:
- n° 1 Manuale di istruzione
- n° 1 Sonda Esterna QAC34/101 (B9) (NTC 1 kΩ)
- n° 1 Cavo per collegamento a bruciatore modulante Ferroli
- n° 1 Sonda QAZ36 (NTC 10 kΩ)
NOTA
Nel Pannello Thermo EBM sono già installati il Termostato Sicurezza Caldaia (TSC), la
Sonda di mandata caldaia QAZ36 (NTC 10 kΩ) e il Relè per modulazione a 3 punti KA1.
Dopo aver tolto l’imballo assicurarsi dell’integrità e della completezza della fornitura
ed in caso di non rispondenza, rivolgersi alla Ferroli SpA o all’Agenzia Ferroli che ha
venduto il Pannello.
5.1 ACCESSORI
- Kit sonda a collare collettore cascata (B 10) QAD 36/101 (NTC 10 kΩ)
- Kit sonda a immersione QAZ 36 (NTC 10 kΩ)
Regolatore RVS 63.238
Morsettiera MP
Asole per passaggio cavi
4 13 2
Etichette
Targhetta tecnica
- 7 -
IT
7. GESTIONE FUNZIONI
8. MONTAGGIO/INSTALLAZIONE
Per il montaggio del Pannello:
- Rimuovere le due viti laterali e sollevare il coperchio.
- Fissare il Pannello alla mantellatura della caldaia utilizzando i 4 fori predisposti.
FUNZIONI
LATO GENERATORE LATO IMPIANTO
CRP-DIRETTO
CR1-MISCELATO
CR2-MISCELATO
GESTIONEPRODUZIONEACS
1
1-2
GESTIONEBRUCIATOREMONOSTADIO
GESTIONEBRUCIATORIBISTADIO
GESTIONEBRUCIATOREMODULANTE
GESTIONEBRUCIATORIGENERATORIINCASCATA
FUNZIONAMENTOTEMPSCORREVOLE(CURVA CLIMATICA)
GESTIONEIMPIANTOMISTOABBINATOAGENERATOREACOMBUSTIBILESOLIDO
GESTIONEIMPIANTOMISTOABBINATOACOLLETTORISOLARI
M
1
2
MAS
SIM
ACO
NFIG
URAZ
IONE
ATTENZIONE: Il Pannello deve essere montato su caldaia. In ogni altro caso, prevedere le adeguate protezioni per il passaggio dei cavi elettrici ed evitare l'accesso a parti in ten-sione, attraverso i fori presenti nella parte inferiore dell'ap-parecchio.
- 8 -
9. SCHEMA ELETTRICO INTERNO
1
- 9 -
IT
10. LEGENDA SIMBOLI/COMPONENTI SCHEMA ELETTRICO
Sim.\ Sym. Sigla \ Item Funzione \ Use type
B2BM
Sonda temperatura acqua mandata caldaia
Boiler water flow temperature probe
Sonda temperatura esterna
Outside temperature probe
Bruciatore
Burner
Lampada alimentazione pannello 230Vac
230Vac panel power supply lamp
Lampada allarme intervento termostato di sicurezza
Safety thermostat alarm lamp
Relè disponibile per bruciatore modulante a 3 punti
3-points modulation burner available relay
Regolatore RVS 63.283/109
RVS 63.283/109 regulator
Interfaccia operatore AVS 37.294
AVS 37.294 operator panel
Interruttore accensione pannello
Panel ignition switch
Interruttore consenso start bruciatore
Burner start switch consent
Termostato di sicurezza caldaia
Boiler safety thermostat
Segnale disponibile allarme TSC (230Vac)
TSC alarm available signal (230Vac)
BUS di comunicazione caldaie in cascata
Boiler cascade comunication BUS
B9BM
BU1BM
HL1QG
HL2QG
KA1QG
N1QG
N2QG
SB1QG
SB2QG
TSCQG
XT1BM
Signal for external Apparatus
Segnalazioni per Apparecchiature
esterne
Segnale a cascata a:Cascade Signal to:MASTER/SLAVE
RVS 63.283/109
XT2BM
- 10 -
11. COLLEGAMENTI AL REGOLATORE
061107B000020
RV
S63.283/109
1PR
VS
63.283/109
S061107000020
USCITA RELÈ (config. LP 5894)
USCITA RELÈ (config. LP 5892)
USCITA RELÈ (config. LP 5891)
VALVOLA MISCELATRICE IMPIANTO CR 2
POMPA IMPIANTO CR 2
USCITA RELÈ (config. LP 5890)
POMPA IMPIANTO CR 1
POMPA DI CARICO BOLLITORE SANITARIO
VALVOLA MISCELATRICE IMPIANTO CR 1
COLLEGAMENTO BRUCIATORE(GIÀ CABLATO)
ALIMENTAZIONE(GIÀ CABLATA)
USCITA DIGITALE / 0-10V - (config. LP 6070)
INGRESSO SONDA (config. LP 5933)
INGRESSO SONDA (config. LP 5932)
INGRESSO SONDA (config. LP 5931)
INGRESSO SONDA (config. LP 5930)
INGRESSO DIGITALE / 0-10V - (config. LP 5960)
INGRESSO DIGITALE / 0-10V - (config. LP 5950)
SONDA ESTERNA
SONDA BOLLITORE ACS
SONDA MANDATA GENERATORE (GIÀ CABLATA)
COLLEGAMENTO BUS GENERATORI IN CASCATA
SONDA MANDATA IMPIANTO CR 2
SONDA MANDATA IMPIANTO CR 1
AVVERTENZE
Èobbligatorio:
•L’impiegodiuninterruttoremagnetotermicoonnipolare,sezionatoredilinea,conaperturadeicontattidialmeno3mm,conformealleNormeEN.IT
•RispettareilcollegamentoL(Fase)-N(Neutro).
•NONutilizzarecavidisezioneinferiorea1,5mm2.
•Lasciareilconduttorediterrapiùlungodialmeno2cmrispettoaquellidiL(Fase)-N(Neutro).
•Riferirsiaglischemielettricidiquestomanualeperqualsiasiinterventodinaturaelettrica.
•Effettuareicollegamentiadunefficaceimpiantodimessaaterra(*).
•NONutilizzareitubidell’acquaperlamessaaterradell’apparecchio.
(*)Il costruttore non è responsabile di eventuali danni causati dalla mancanza di messa a terra dell’apparecchio e dall’inosservanza di
quanto riportato negli schemi elettrici.
LEGENDALP: Linea/parametroCR1: Circuito riscaldamento miscelato 1CR2: Circuito riscaldamento miscelato 2ACS: Circuito acqua calda sanitaria
- 11 -
IT
12. COLLEGAMENTI ELETTRICI PANNELLO-BRUCIATORE
Collegamenti a cura dell’installatore.
12.1 PANNELLO - BRUCIATORE MONOSTADIO
12.2 PANNELLO - BRUCIATORE BISTADIO
- 12 -
12.3 PANNELLO - BRUCIATORE MODULANTE 3 PUNTI
12.4 PANNELLO - BRUCIATORE MODULANTE 3 PUNTI FERROLI
- 13 -
IT
13. GESTIONE MASSIMA IMPIANTI
IMPORTANTE:
Lo schema di impianto riportato in questa pagina è esem-
plificativo e non contempla le apparecchiature di sicurezza
previste dalla normativa in vigore.
L’alimentazione di rete e la sonda di mandata caldaia (B2)
sono già cablati di serie.
UTS
B9
Q3
B3ACS
RMB2
Q12 B7
TSC
B1
Q2
Y1/Y2
TSX
CR1
Q20
B12
Q6
Y5/Y6
TSX
CR2
CRP
CONNESSIONI ELETTRICHE AL REGOLATORE RVS63.283
Gli schemi sottoriportati indicano i collegamenti che l’installatore deve eseguire per la massima gestione impianti del Pannello Thermo EBM.
061107B000020RVS63.283/109
1PRVS63.283/109
S061107000020
MY1/Y2 Q2Q6Q20Q12 Q3
B9 B3 B2B1B12
MY5/Y6
BRUC
IATO
RE
ALIM
ENTA
ZION
E
QX
2
BX
1
B7 H1
LEGENDA
UTS Uscita tubo di sicurezza
M Mandata impianto
R Ritorno impianto
Circuito idraulico
Collegamento elettrico
TSX Termostato sicurezza impianto
(a cura cliente)
CR1 Circuito riscaldamento miscelato 1
CR2 Circuito riscaldamento miscelato 2
CRP Circuito riscaldamento diretto
ACS Circuito acqua calda sanitaria
B2 Sonda mandata caldaia
B9 Sonda esterna
TSC Termostato di sicurezza caldaia
B3 Sonda bollitore
Q3 Pompa bollitore
B1 Sonda mandata impianto CR1
Q2 Pompa CR1
Y1/Y2 Valvola miscelatrice CR1
B12 Sonda mandata impianto CR1
Q6 Pompa CR2
Q12 Pompa by-pass caldaia
Y5/Y6 Valvola miscelatrice CR2
Q20 Pompa CRP
- 14 -
14. COLLEGAMENTO DI GENERATORI IN CASCATA
Il Pannello comandi Thermo EBM, consente la gestione integrata fino ad un massimo di 16 generatori in cascata.
OgnicaldaiadovràessereequipaggiataconunpannellocollegatotramiteuncavoBUSsecondoloschemadiquestapagina.
MASTER
B9
GENERATORE 1
COLLEGAMENTO BUS
GENERATORE 2 GENERATORE N
COLLETTOREMANDATACOMUNE
COLLETTORERITORNOCOMUNE
B10
SLAVE SLAVE
Q1 Q1 Q1
B2 B2 B2
GENERATORE 1(master)
061107B000020RVS63.283/109
1PRVS63.283/109
S061107000020
Q1
GENERATORE 2(slave)
061107B000020RVS63.283/109
1PRVS63.283/109
S061107000020
GENERATORE 3(slave)
061107B000020RVS63.283/109
1PRVS63.283/109
S061107000020
BUS BUS BUS
BRUCIATORE ALIMENTAZIONE
QX
2
B9B10 B2 B2
Q1 Q1BRUCIATORE ALIMENTAZIONE BRUCIATORE ALIMENTAZIONE
QX
2
B2
LegendaB2 Sonda mandata caldaiaB9 Sonda esternaB10 Sonda mandata collettoreQ1 Pompe mandate caldaie Circuito idraulico Collegamento elettrico
IMPORTANTE: Gli schemi di impianto riportati in questa pagina sono esemplificativi e non contemplano le appa-recchiature di sicurezza previste dalla normativa in vigore.Collegamenti bruciatore, alimentazione, B2 sonda mandata generatore già cablati di serie e da ripetere per ogni generatore della cascata.
Collegamento/ConfigurazioneQ1 Su morsetto Qx2 da impostare - LP 5891B10 Su morsetto Bx1 da impostare - LP 5930
Nota - ÈammessoilcollegamentoincascatadipiùgeneratoriconunicapompadicircolazioneQ25 comandata dal regolatore master. In tal caso utilizzare una delle uscite Qx (ad esempio Qx2) del regolatore master per pilotare Q25, impostare la linea di programma LP opportuna (ad esempio LP 5891). Per approfondimenti si rimanda agli schemi idraulici del paragrafo "Esempi di schemi realizzabili" e al paragrafo "Visualizzazione e gestione dei parametri".
Lunghezza ammessa dei cavi bipolari BUS LPB (rame)Con alimentazione BUS tramite
regolatore (punto a punto) Con alimentazione BUS centrale
Sezione cavo 1,5 mm2
Lunghezza max 250 m 460 m
Nota - Rispettare la polarità dei fili del cavo BUS LPB.
- 15 -
IT
15. SONDE
16. SONDA ESTERNA
Le sonde utilizzabili con il Pannello Thermo EBM sono riportate in tabella.
Per il buon funzionamento del sistema è importante che le sonde siano posizionate e collegate correttamente e che eventuali canalizzazioni dei cavi di colle-
gamento siano separate da quelle dei cavi in tensione (230 Vac).
ELENCO DELLE SONDE
Per il buon funzionamento del Pannello è molto importante l’impiego della sonda esterna (B9) che deve essere installata all’esterno dell’edificio da riscaldare,
seguendo le indicazioni riportate sulla confezione della sonda. Per il collegamento elettrico tra la sonda esterna ed il Pannello Thermo EBM utilizzare i morsetti
dedicati M-B9 del regolatore RVS 63-283.
B1 Sonda mandata CR1 B22 Sonda caldaia comb. solido (mandata) B70 Sonda ritorno cascata
B2 Sonda di caldaia (mandata) B31 Sonda bollitore ACS (accumulo, in basso) B73 Sonda di ritorno comune dal circuito primario
B3 Sonda bollitore ACS (accumulo, in alto) B35 Sonda temperatura mandata ACS
B4 Sonda serbatoio di riserva Buffer (in alto) B36 Sonda carico ACS (accumulo)
B6 Sonda collettore solare B38 Sonda uscita riscaldatore istantaneo ACS
B7 Sonda ritorno caldaia B39 Sonda circolazione ACS
B8 Sonda temperatura fumi B41 Sonda serbatoio di riserva Buffer (in basso)
B9 Sonda esterna B42 Sonda serbatoio di riserva Buffer (intermedia)
B10 Sonda mandata comune (cascata) B61 Sonda 2° collettore solare
B12 Sonda mandata CR2 B63 Sonda mandata solare
B13 Sonda piscina B64 Sonda ritorno solare
AVVERTENZE
•Lasondavaposizionatasullatonordonord-ovestdell'edificio
•Lasondavapostainuntrattodimuroliscio;incasodimattoniavistaodipareteirregolare,vaprevistaun’areadicontattoliscia.
•Ilcavodicollegamentotrasondaesternaequadrodicomandonondeveaveregiunte;nelcasofosseronecessarie,devonoesserestagnateeadegua-
tamente protette.
•Eventualicanalizzazionidelcavodicollegamentodevonoessereseparatedacaviintensione(230Vac).
Lunghezza ammessa dei cavi delle sonde (rame)
Sezione del cavo 0,75 1,0 1,5 mm2
Lunghezza max 60 80 120 m
- 16 -
TABELLA DI CORRISPONDENZA
Temperatura rilevata (°C) - Valore resistivo della sonda (Ω).
•Sonda esterna NTC 1 k Ω (B9)
T (°C) R (Ω) T (°C) R (Ω) T (°C) R (Ω) T (°C) R (Ω)-30,0 13’034 -9,0 4’358 12.0 1’690 33.0 740
-29,0 12’324 -8,0 4’152 13.0 1’621 34.0 713
-28,0 11’657 -7,0 3’958 14.0 1’555 35.0 687
-27,0 11’031 -6,0 3’774 15.0 1’492 36.0 663
-26,0 10’442 -5,0 3’600 16.0 1’433 37.0 640
-25,0 9’889 -4,0 3’435 17.0 1’375 38.0 617
-24,0 9’369 -3,0 3’279 18.0 1’320 39.0 595
-23,0 8’880 -2,0 3’131 19.0 1’268 40.0 575
-22,0 8’420 -1,0 2’990 20.0 1’218 41.0 555
-21,0 7’986 0.0 2’857 21.0 1’170 42.0 536
-20,0 7’578 1.0 2’730 22.0 1’125 43.0 517
-19,0 7’193 2.0 2’610 23.0 1’081 44.0 500
-18,0 6’831 3.0 2’496 24.0 1’040 45.0 483
-17,0 6’489 4.0 2’387 25.0 1’000 46.0 466
-16,0 6’166 5.0 2’284 26.0 962 47.0 451
-15,0 5’861 6.0 2’186 27.0 926 48.0 436
-14,0 5’574 7.0 2’093 28.0 892 49.0 421
-13,0 5’303 8.0 2’004 29.0 859 50.0 407
-12,0 5’046 9.0 1’920 30.0 827
-11,0 4’804 10.0 1’840 31.0 796
-10,0 4’574 11.0 1’763 32.0 767
- 17 -
IT
17. INTERFACCIA AVS 37.294
L’interfacciapuòessereutilizzatadall’Utente,dalServizioTecnicoedall’Installatore,chiamatipersemplicità“Operatore”,pereffettuareleoperazionide-
scritte nelle pagine seguenti.
L’interfaccia è collegata, con cavo flat, al regolatore RVS 63.283 ed è costituita da:
OKESC
0 4 8 12 16 20 24
AUTO
Selezione riscaldamento ACS
Display Selezione regime di funzionamento
Informazioni
Conferma la selezionee/o la modifica effettuata
Funzione spazzacaminoe/o test TSC
Funzione manualeAnnulla la selezionee/o la modifica effettuata
Connettore di servizio (BSB)
Navigazione, impostazione parametri, modifica valori
Display
LegendaRiscaldamento al setpoint Comfort
Riscaldamento al setpoint ridotto
Riscaldamento al setpoint protezione antigelo
In elaborazione - prego attendere
Bruciatore in funzione (solo bruciaore olio/gas)
Livello info attivo Riscaldamento al setpoint ridotto
Programmazione attiva
SistemariscaldamentotemporaneamenteOFF
funzioniECOattive
Funzione vacanza attiva
Riferimento al circuito di riscaldamento
Modalità speciale / manutenzione
Messaggio d’errore
Xxxxxxxxxxxxxxxxxxxxxxxx
XxxxxxxxxxxxxxxxxxxxxxxxXxxxxxxxxxxxxxxxxxxxxxxx
INFO PROG ECO
No.8 8 8 8
1 8 8 8 8 81
- 18 -
Selezione regime di funzionamento
Auto
Funzionamento Automatico
Il funzionamento automatico controlla la temperatura ambiente in base al programma orario impostato.
Caratteristiche del funzionamento automatico:
•Modalitàriscaldamentoinbasealprogrammaorario
•Setpointditemperaturasecondoilprogramma“SetpointComfort”oppureil“Setpointridotto”
•Funzionidiprotezioneattive
•Commutazioneautomaticaestate/inverno(funzioniECO)
Funzionamento Continuo oppure
Il funzionamento continuo mantiene la temperatura ambiente al livello regolato.
Riscaldamento al setpoint Comfort
Riscaldamento al setpoint ridotto
Caratteristiche del funzionamento Continuo:
•Riscaldamentosenzaconsiderazionedelprogrammaorario
•Funzionidiprotezioneattive
•Commutazioneautomaticaestate/invernoelimite24orediriscaldamentononattivo,incasodifunzionamento
continuo con setpoint Comfort
Modalità Protezione
In modalità protezione il riscaldamento non è attivo.
Sono attive le protezioni antigelo (deve essere allacciata l’alimentazione elettrica).
Caratteristiche modalità Protezione:
•Riscaldamentooff
•Temperaturaalsetpointprotezioneantigelo
•Funzionidiprotezioneattive
Auto
- 19 -
IT
Modalità ACS
•On:L’acquasanitariaèriscaldatasecondoilprogrammaorarioimpostato
•Off:Ilriscaldamentodell’acquasanitarianonvieneeffettuato;lafunzionediprotezioneantigeloèattiva
La modalità ACS può essere attivata anche quando i circuiti di riscaldamento sono in modalità vacanza.
Nota
In caso di necessità è possibile effettuare il riscaldamento rapido di un carico bollitore tenendo premuto
il tasto per circa 4 secondi.
Il tasto informazioni:
a - se premuto brevemente, dalla pagina base, permette di visualizzare:
•Eventualimessaggidierroreoallarmidimanutenzione
•Eventualimessaggispeciali
oppure
•Temperaturadicaldaia
•Temperaturaesterna
•Temperaturaesternaminima
•Temperaturaesternamassima
•TemperaturaACS
•Statocircuitoriscaldamento1
•Statocircuitoriscaldamento2
•StatocircuitoriscaldamentoP
•StatoACS
•Statocaldaia
•Statosolare
•Statocaldaiaacombust.solido
•Statodell’accumulobuffer
•Ora/datadelgiorno
•Telefonoassistenzaclienti
b - se premuto per circa 4 secondi, dopo la pressione del tasto permette di entrare nel menu.
Selezione regime di riscaldamento ACS
Informazioni
temperatura ambiente
20.518:28
INFO
0 4 8 12 16 20 24
AUTO
Errore30: Sensore di flusso 1
02.0.1
INFO
0 4 8 12 16 20 24
AUTO
303: funzione spazzacamino
02.0.1
INFO
0 4 8 12 16 20 24
AUTO
room temperature
20.518:28
INFO
0 4 8 12 16 20 24
AUTO
Error30: Flow sensor 1
02.0.1
INFO
0 4 8 12 16 20 24
AUTO
303: chimney sweep function
02.0.1
INFO
0 4 8 12 16 20 24
AUTO
OK ESC
- 20 -
La funzione spazzacamino si attiva premendo per circa 3 secondi il tasto .
Essa produce lo stato di funzionamento necessario che consente allo specialista di effettuare l’analisi dei
fumi di scarico.
In caso di messaggi speciali il display visualizza uno dei seguenti simboli:
Messaggio d’errore
Si è verificato un errore di impianto.
Premere il tasto per ottenere ulteriori informazioni.
Modo manutenzione o speciale
Si è verificato un allarme manutenzione oppure l’impianto è passato
in modalità speciale.
Premere il tasto per ottenere ulteriori informazioni.
LafunzionediresetpericontatoriedalcuniparametrièconsigliatovengaeffettuatoSOLOdallospecialistare-
sponsabile della manutenzione. Quando questa funzione è consentita sul display viene visualizzata l’opzione Si/No.
Dopo il reset i parametri riprendono le impostazioni di fabbrica (default).
Quando il controllo manuale è attivo, i relè non sono più alimentati e disattivati secondo il regime di funziona-
mento impostato ma, in base alle loro funzioni, conformemente allo stato di funzionamento manuale predefinito.
Il relè del bruciatore, alimentato tramite controllo manuale, può essere disalimentato attraverso il regolatore di
temperatura elettronico (TR).
Messaggi speciali
Funzione Reset
Controllo manuale
Funzione spazzacamino
Test TSC
Correzione Setpoint con controllo manuale
siReset ?
Il controllo manuale si attiva con il tasto e sul display appare il simbolo modalità manutenzione/speciale.
Premere il pulsante per passare alla visualizzazione info “Controllo manuale”, e per poter modificare quindi il setpoint.
temperatura ambiente
20.518:28
INFO
0 4 8 12 16 20 24
AUTO
Errore30: Sensore di flusso 1
02.0.1
INFO
0 4 8 12 16 20 24
AUTO
303: funzione spazzacamino
02.0.1
INFO
0 4 8 12 16 20 24
AUTO
room temperature
20.518:28
INFO
0 4 8 12 16 20 24
AUTO
Error30: Flow sensor 1
02.0.1
INFO
0 4 8 12 16 20 24
AUTO
303: chimney sweep function
02.0.1
INFO
0 4 8 12 16 20 24
AUTO
temperatura ambiente
20.518:28
INFO
0 4 8 12 16 20 24
AUTO
Errore30: Sensore di flusso 1
02.0.1
INFO
0 4 8 12 16 20 24
AUTO
303: funzione spazzacamino
02.0.1
INFO
0 4 8 12 16 20 24
AUTO
room temperature
20.518:28
INFO
0 4 8 12 16 20 24
AUTO
Error30: Flow sensor 1
02.0.1
INFO
0 4 8 12 16 20 24
AUTO
303: chimney sweep function
02.0.1
INFO
0 4 8 12 16 20 24
AUTO
Per effettuare il test TSC (Termostato Sicurezza Caldaia) tenere premuto il tasto .
Il test TSC deve essere effettuato SOLAMENTE dallo Specialista responsabile della manutenzione poichè
la temperatura dell’acqua in caldaia viene innalzata fino al suo limite massimo.
È VIETATO a qualunque altro operatore eseguire questo test.
- 21 -
IT
Premere il tasto Per entrare nella pagina successiva
Ruotare la manopolaPer selezionare la riga “Bedieneinheit” (“Unità di comando”)
Premere 2 volte il tasto
Per:- Confermare la riga selezionata- Entrare nella pagina della lingua (Sprache) per
consentire la modifica della lingua selezionata (lampeggiante)
Ruotare la manopola Per selezionare la lingua preferita (es. italiano)
Premere il tasto Per confermare la lingua selezionata
Premere il tasto Per tornare al sottomenu "utente finale"
Il Regolatore del Pannello Thermo EBM è organizzato in “pagine e righe” e per navigare, effettuare le impostazioni dei parametri, le regolazioni/modifiche dei
valori, si usano fondamentalmente i tasti seguenti:
IlRegolatoredelPannelloThermoEBMèconfiguratoinfabbricaperiltedesco.ÈperòpossibilecambiarelalinguaselezionandoquellapreferitatraInglese,
Tedesco,Francese,Italiano,Olandese,Spagnolo,Portoghese,Danese,Finlandese,Svedese.
Per selezionare la lingua preferita, partendo dalla “pagina di base”:
18. IMPOSTAZIONI E PROGRAMMAZIONE
18.2 SCELTA DELLA LINGUA
Per:
- selezionare le righe/parametri di interesse
- modificare i valori e abilitare/disabilitare le funzioni
Per confermare la riga selezionata ed entrare nella pagina corrispondente
Per tornare alla pagina precedente senza memorizzare la modifica effettuata
Per:
- visualizzare le informazioni
- selezionare i menu, se è tenuto premuto per circa 4 secondi, dopo aver premuto il tasto dalla “pagina di base”
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
ItalianoSprache
PROG
No. 20
Unità di comando
ItalianoLingua
PROG
No. 20
Ora e dataUnità di comando
PROG
Ora e data
Ore / minuti
PROG
No. 1
01:2521.2
1
Temperatura caldaia
21.2
Ora e data
Ore / minuti
PROG
No. 1
14:17
Ora e data
Giorno / mese
PROG
No. 2
05:03
Ora e data
Anno
PROG
No. 3
2013
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
ItalianoSprache
PROG
No. 20
Unità di comando
ItalianoLingua
PROG
No. 20
Ora e dataUnità di comando
PROG
Ora e data
Ore / minuti
PROG
No. 1
01:2521.2
1
Temperatura caldaia
21.2
Ora e data
Ore / minuti
PROG
No. 1
14:17
Ora e data
Giorno / mese
PROG
No. 2
05:03
Ora e data
Anno
PROG
No. 3
2013
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
ItalianoSprache
PROG
No. 20
Unità di comando
ItalianoLingua
PROG
No. 20
Ora e dataUnità di comando
PROG
Ora e data
Ore / minuti
PROG
No. 1
01:2521.2
1
Temperatura caldaia
21.2
Ora e data
Ore / minuti
PROG
No. 1
14:17
Ora e data
Giorno / mese
PROG
No. 2
05:03
Ora e data
Anno
PROG
No. 3
2013
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
ItalianoSprache
PROG
No. 20
Unità di comando
ItalianoLingua
PROG
No. 20
Ora e dataUnità di comando
PROG
Ora e data
Ore / minuti
PROG
No. 1
01:2521.2
1
Temperatura caldaia
21.2
Ora e data
Ore / minuti
PROG
No. 1
14:17
Ora e data
Giorno / mese
PROG
No. 2
05:03
Ora e data
Anno
PROG
No. 3
2013
Per effettuare la prima messa in servizio del Pannello Thermo EBM:
18.1 PRIMA MESSA IN SERVIZIO
-Accertarsichel’interruttore(2)“consensostartbruciatore”siainposizione“noninserito”(OFF)
-Posizionaresu“ON”l’interruttoregeneraledelquadroelettricodiCentrale
- Premere l’interruttore (1) (accensione della segnalazione verde) per alimentare il Pannello
- Attendere l’aggiornamento automatico del sistema fino alla visualizzazione della “pagina di base”.
Nel caso in cui la visualizzazione non fosse quella di base premere il tasto
34 2 1
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
ItalianoSprache
PROG
No. 20
Unità di comando
ItalianoLingua
PROG
No. 20
Ora e dataUnità di comando
PROG
Ora e data
Ore / minuti
PROG
No. 1
01:2521.2
1
Temperatura caldaia
21.2
Ora e data
Ore / minuti
PROG
No. 1
14:17
Ora e data
Giorno / mese
PROG
No. 2
05:03
Ora e data
Anno
PROG
No. 3
2013
OK ESC
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
ItalianoSprache
PROG
No. 20
Unità di comando
ItalianoLingua
PROG
No. 20
Ora e dataUnità di comando
PROG
Ora e data
Ore / minuti
PROG
No. 1
01:2521.2
1
Temperatura caldaia
21.2
Ora e data
Ore / minuti
PROG
No. 1
14:17
Ora e data
Giorno / mese
PROG
No. 2
05:03
Ora e data
Anno
PROG
No. 3
2013
OK ESC
- 22 -
18.3 REGOLAZIONE DELL'ORA E DELLA DATA
Premere il tasto
Ruotare la manopola
Per selezionare la pagina precedente
Perselezionarelariga“Oraedata”
Premere 2 volte il tasto Per:-confermarelariga“Oraedata”- selezionare l’ora (lampeggiante) per la regolazione
Ruotare la manopola
Premere il tasto
Ruotare la manopola
Premere il tasto
Per regolare l’ora
Per confermare la regolazione effettuata e passare ai “minuti” (lampeggiante)
Per regolare i “minuti”
Per confermare la regolazione effettuata
Ruotare la manopola
Premere il tasto
Ruotare la manopola
Premere il tasto
Ruotare la manopola
Premere il tasto
Per selezionare la pagina del “giorno/mese” correnti
Per selezionare il “mese” (lampeggiante)
Per regolare il “mese corrente” (es. 03)
Per confermare la regolazione effettuata e passare al “giorno”
Per regolare il “giorno corrente” (es. 05)
Per confermare la regolazione effettuata
Ruotare la manopola
Premere il tasto
Ruotare la manopola
Premere il tasto
Per selezionare la pagina ”anno”
Per selezionare ”anno” (lampeggiante)
Per regolare l’”anno” corrente (es. 2013)
Per confermare la regolazione effettuata
Premere 2 volte il tasto Per ritornare alla pagina base
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
ItalianoSprache
PROG
No. 20
Unità di comando
ItalianoLingua
PROG
No. 20
Ora e dataUnità di comando
PROG
Ora e data
Ore / minuti
PROG
No. 1
01:2521.2
1
Temperatura caldaia
21.2
Ora e data
Ore / minuti
PROG
No. 1
14:17
Ora e data
Giorno / mese
PROG
No. 2
05:03
Ora e data
Anno
PROG
No. 3
2013
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
ItalianoSprache
PROG
No. 20
Unità di comando
ItalianoLingua
PROG
No. 20
Ora e dataUnità di comando
PROG
Ora e data
Ore / minuti
PROG
No. 1
01:2521.2
1
Temperatura caldaia
21.2
Ora e data
Ore / minuti
PROG
No. 1
14:17
Ora e data
Giorno / mese
PROG
No. 2
05:03
Ora e data
Anno
PROG
No. 3
2013
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
ItalianoSprache
PROG
No. 20
Unità di comando
ItalianoLingua
PROG
No. 20
Ora e dataUnità di comando
PROG
Ora e data
Ore / minuti
PROG
No. 1
01:2521.2
1
Temperatura caldaia
21.2
Ora e data
Ore / minuti
PROG
No. 1
14:17
Ora e data
Giorno / mese
PROG
No. 2
05:03
Ora e data
Anno
PROG
No. 3
2013
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
ItalianoSprache
PROG
No. 20
Unità di comando
ItalianoLingua
PROG
No. 20
Ora e dataUnità di comando
PROG
Ora e data
Ore / minuti
PROG
No. 1
01:2521.2
1
Temperatura caldaia
21.2
Ora e data
Ore / minuti
PROG
No. 1
14:17
Ora e data
Giorno / mese
PROG
No. 2
05:03
Ora e data
Anno
PROG
No. 3
2013
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
ItalianoSprache
PROG
No. 20
Unità di comando
ItalianoLingua
PROG
No. 20
Ora e dataUnità di comando
PROG
Ora e data
Ore / minuti
PROG
No. 1
01:2521.2
1
Temperatura caldaia
21.2
Ora e data
Ore / minuti
PROG
No. 1
14:17
Ora e data
Giorno / mese
PROG
No. 2
05:03
Ora e data
Anno
PROG
No. 3
2013
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
ItalianoSprache
PROG
No. 20
Unità di comando
ItalianoLingua
PROG
No. 20
Ora e dataUnità di comando
PROG
Ora e data
Ore / minuti
PROG
No. 1
01:2521.2
1
Temperatura caldaia
21.2
Ora e data
Ore / minuti
PROG
No. 1
14:17
Ora e data
Giorno / mese
PROG
No. 2
05:03
Ora e data
Anno
PROG
No. 3
2013
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
- 23 -
IT
19. PROGRAMMAZIONE
19.1 PROCEDURA DI ACCESSO RAPIDO AI SOTTOMENU DELL'UTENTE FINALE
19.2 PROCEDURA DI ACCESSO AI SOTTOMENU
All’accensione del Pannello, sul display si visualizza la pagina base.
Premere il tasto per accedere direttamente ai sottomenu.
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
ItalianoSprache
PROG
No. 20
Unità di comando
ItalianoLingua
PROG
No. 20
Ora e dataUnità di comando
PROG
Ora e data
Ore / minuti
PROG
No. 1
01:2521.2
1
Temperatura caldaia
21.2
Ora e data
Ore / minuti
PROG
No. 1
14:17
Ora e data
Giorno / mese
PROG
No. 2
05:03
Ora e data
Anno
PROG
No. 3
2013
UTENTE FINALE
SO
TTO
MEN
UOraedata
Unità di comando
Programma orario CR1
Programma orario CR2
Programma orario 4/ACS
Programma orario 5
Vacanze CR1
Vacanze CR2
Circuito riscaldamento 1
Circuito riscaldamento 2
Funz. Manutenzione/service
Parametri diagnostica
OK ESC
MENUUtente finale Messa in servizio Specialista OEM
SO
TTO
MEN
U
Oraedata Oraedata Oraedata
Di c
ompe
tenz
a es
clus
iva
di F
ERRO
LI S
.p.A
.
Unità di comando Unità di comando Unità di comando
Programma orario CR1 Programma orario CR1 Programma orario CR1
Programma orario CR2 Programma orario CR2 Programma orario CR2
Programma orario 4/ACS Programma orario 4/ACS Programma orario 4/ACS
Programma orario 5 Programma orario 5 Programma orario 5
Vacanze CR1 Vacanze CR1 Vacanze CR1
Vacanze CR2 Vacanze CR2 Vacanze CR2
Circuito riscaldamento 1 Circuito riscaldamento 1 Circuito riscaldamento 1
Circuito riscaldamento 2 Circuito riscaldamento 2 Circuito riscaldamento 2
- - Caldaia
- Configurazione Configurazione
- LPB LPB
- Guasto Guasto
Funz. Manuten/service Funzion. Manuten/service Funzion. Manuten/service
- Test input/output Test input/output
- Stato Stato
Parametri diagnostica Parametri diagnostica Parametri diagnostica
- Diagnostica utenze Diagnostica utenze
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
ItalianoSprache
PROG
No. 20
Unità di comando
ItalianoLingua
PROG
No. 20
Ora e dataUnità di comando
PROG
Ora e data
Ore / minuti
PROG
No. 1
01:2521.2
1
Temperatura caldaia
21.2
Ora e data
Ore / minuti
PROG
No. 1
14:17
Ora e data
Giorno / mese
PROG
No. 2
05:03
Ora e data
Anno
PROG
No. 3
2013
All’accensione del Pannello, sul display si visualizza la pagina base.
Premere il tasto
Tenere premuto il tasto per 4 secondi per accedere ai menu.
Ruotare la rotella per selezionare il menu desiderato.
Premere il tasto per accedere ai sottomenu seguenti.
OK ESC
OK ESC
OK ESC
IMPORTANTE: Il Menu OEM è protetto da password e la gestione dei Sottomenu e delle Linee/ParametrisonodicompetenzaSOLOdiFerroliS.p.A.
Per l’eventuali modifiche contattare il Centro Assistenza Ferroli Autorizzato di competenza oppure il Servizio Assistenza Ferroli.
- 24 -
Attenzione! Togliere l’alimentazione prima di effettuare i collegamenti del bruciatore.
Effettuare le connessioni elettriche tra pannello e bruciatore secondo quanto indicato al paragrafo “COLLEGAMENTIELETTRICIPANNELLO-BRUCIATORE”.
Attenzione! Effettuare queste impostazioni con bruciatore disattivato e alimentazione pannello attiva.
Menù Messa in servizio (Specialista) - Sottomenù Configurazione
20. CONFIGURAZIONE PER LA GESTIONE DEL BRUCIATORE
20.1 BRUCIATORE MODULANTE
L’installazione di un bruciatore modulante implica la regolazione ottimale dell’azione di regolazione della fiamma.
Vietato! Queste impostazioni devono essere eseguite solo da specialisti esperti (tecnico bruciatorista e Sevizio Assistenza Tecnica
Ferroli). I seguenti parametri sono protetti da password (interpellare il Sevizio Assistenza Tecnica Ferroli).
Menù OEM (Protetto da password) - Sottomenù Configurazione
Prog N°(sul
display)
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
Setup
5770 Tipo di generatore 2 stadi in relazione al tipo di bruciatore
Tempo di apertura dell’attuatore di smorzamento. Per assicurare il controllo ottimale del sistema di modulazione del bruciatore, configurare il tempo di apertura dell’attuatore di smorzamento.
Esempio: Tempo di apertura dell’attuatore di smorzamento (90°) = 120 secondi Posizione minima dell’attuatore di smorzamento = 20° Posizione massima dell’attuatore di smorzamento = 80° Pertanto, l’effettivo tempo di apertura dell’attuatore della serranda aria del bruciatore utilizzabile per il controllo è il seguente:
120 s x (80°-20°) = 80 s 90° Impulsi di posizionamento: Il controllo avviene per mezzo di impulsi di posizionamento della serranda. La durata minima di questi impulsi in funzione del tempo di apertura dell’attua-
tore di smorzamento risultano definiti come segue: Tempo di apertura dell'attuatore TS Lunghezza minima dell'impulso 7.5 s - 14.5 s circa 200 ms 15 s - 29.5 s circa 300 ms 30 s - 59.5 s circa 500 ms 60 s - 119.5 s circa 1.10 s > 120 s circa 2.20 s
Modulazione Xp. Xp influenza l’azione proporzionale del regolatore.
Impostando una corretta banda proporzionale, la modulazione del bruciatore viene adattata al comportamento dell’impianto.
Modulazione Tn. Tn influenza l’azione integrale del regolatore.
Impostando il corretto tempo di azione integrale, la modulazione del bruciatore viene adattata al comportamento dell’impianto.
Modulazione Tv. Tv influenza l’azione derivativa del regolatore. Con Tv = 0, l’azione derivativa viene disattivata.
Impostando un corretto tempo di azione derivativo, la modulazione del bruciatore viene adattata al comportamento dell’impianto.
Prog N°(sul
display)
Presenzanel menu
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
CampoUnità
di misuraMin Max
Caldaia
2232 OEM Tempo di apertura dell’attuatore di smorzamento 60 7.5 480 s
2233 OEM Modulazione Xp 20 1 200 °C
2234 OEM Modulazione Tn 150 10 873 s
2235 OEM Modulazione Tv 4.5 0 30 s
- 25 -
ITSi consiglia verificare i parametri 2210 (limite minimo del setpoint di temperatura di caldaia) e 2212 (limite massimo del setpoint di temperatura di caldaia).
Modificarli a seconda delle esigenze del proprio impianto.
Menù specialista - Sottomenù Caldaia
21. CONFIGURAZIONE DEI LIMITI DI FUNZIONAMENTO DELLA CALDAIA
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
Setup
2210 Setpoint minimo 40°C 40°C
2212 Setpoint massimo 80°C 80°C
Si rimanda alla lista completa dei parametri del regolatore per maggiori informazioni.
22. GESTIONE CIRCUITI RISCALDAMENTO
Di seguito elenchiamo alcuni consigli ed indicazioni per la messa in servizio degli impianti di riscaldamento miscelati. Per il collegamento delle sonde di man-
datadegliimpianti,lepompedicircolazioneelevalvolemiscelatricidegliimpiantiCR1eCR2fareriferimentoalparagrafo“GESTIONEMASSIMAIMPIANTI”.
Attenzione! Togliere l’alimentazione del pannello prima di effettuare i collegamenti delle sonde e dei carichi.
Attenzione! Prima di attivare il funzionamento del bruciatore, verificare se i circuiti di riscaldamento miscelato interessano un impianto a pa-
vimento. La massima temperatura di mandata del circuito (vedere tabella successiva) dovrà attenersi alle indicazioni fornite dal costruttore della
pavimentazione. Il corretto funzionamento è assicurato solo in impianti adeguatamente installati (sistema idraulico, installazione elettrica, imposta-
zione parametri). In caso di mancata osservanza di quanto sopra, il pavimento potrebbe subire danni!
Nel caso di riscaldamento “pronto posa” si menziona la possibilità di usufruire della “funzione massetto” che consente di seguire determinati profili
di temperatura in funzione del tempo (per maggiori informazioni consultare la lista completa dei parametri e/o contattare il Servizio Assistenza Ferroli).
Menù Messa in servizio (Specialista) - Sottomenù Circuito riscaldamento CR1, CR2, CRP
21.1 REGOLAZIONE LIMITI DI FUNZIONAMENTO OEM DELLA CALDAIA
In particolari situazioni, quando il modello di caldaia lo consente, si possono richiedere temperature di funzionamento massime più elevate e/o temperature
di funzionamento minime inferiori rispetto le impostazioni di fabbrica. Come già indicato i parametri 2210 e 2212 possono essere modificati per adattare il
funzionamento in base alle esigenze d’impianto. Sono ammesse variazioni di questi parametri entro determinati limiti. Questi limiti sono rappresentati dai
parametri 2211 e 2213. Sono parametri protetti da password, eventuali modifiche devono essere effettuate dal costruttore.
Vietato! Queste impostazioni devono essere eseguite solo da specialisti esperti (Installatore e Sevizio Assistenza Tecnica Ferroli).
I seguenti parametri sono protetti da password (interpellare il Sevizio Assistenza Tecnica Ferroli).
Menu OEM (Protetto da password) - Sottomenu Caldaia
Punti di funzionamento minimo / massimo OEM. Rappresentano i limiti inferiore e superiore oltre i quali non possono essere modificati i parametri 2210 e 2212.
Prog N°(sul
display)
Presenzanel menu
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
CampoUnità
di misuraMin Max
Caldaia
2211 OEM PuntodifunzionamentominimoOEM 40 8 95 °C
2213 OEM PuntodifunzionamentomassimoOEM 85 8 120 °C
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
Setup
740, 1040, 1340Setpoint temperatura di mandata minima CR1, CR2, CRP
8°C 8°C
741, 1041, 1341Setpoint temperatura di mandata massima CR1, CR2, CRP
80°CImpostare in base alla massima temperatura impianto ammessa
- 26 -
Se è necessaria la gestione di un ulteriore Impianto di riscaldamento diretto, è possibile utilizzare una delle uscite QX ed impostarla come alimentazione
o consenso funzionamento Pompa circuito diretto Q20 (vedere tabella seguente e lista completa dei parametri).
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
Setup
5710 Circuito riscaldamento 1 On On/Offasecondadelleesigenze
5715 Circuito riscaldamento 2 On On/Offasecondadelleesigenze
Menù Messa in servizio (Specialista) - Sottomenù Configurazione
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
Setup
5890, 5891, 5892, 5894 Uscite relè QX1, QX2, QX3, QX4 Nessuno Pompa CRP Q20
N.B. Le uscite QX1, QX2, QX3 sono attive con tensione 230Vac mentre QX4 è un’uscita contatti puliti in scambio (FX4 è il comune).
Menù Messa in servizio (Specialista) - Sottomenù Configurazione
22.1 CONTROLLO VALVOLA MISCELATRICE
Qualora si utilizzino valvole miscelatrici nei circuiti di riscaldamento miscelati, andrebbero verificati e modificati i seguenti parametri:
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
Setup
830, 1130 Boost valvola miscelatrice 5°C Configurare a seconda delle esigenze
832, 1132 Tipo attuatore 3-punti3-punti oppure 2-punti
a seconda del tipo di attuatore
833, 1133DifferenzialeCommutazione 2 pos
2°CVerificare le caratteristiche dell’attuatore a 2 posizioni
834, 1134 Tempo di corsa attuatore 120s Verificare le caratteristiche dell’attuatore
Si deve selezionare il tipo di attuatore (“3-punti” o “2-punti”) e nel caso di attuatore “2-punti” si deve adattare il differenziale di commutazione in funzione
delle caratteristiche dello stesso. Per una corretta miscelazione, il valore attuale della temperatura di mandata di caldaia deve essere maggiore del setpoint
dellatemperaturadimandatadellavalvolamiscelatrice;diversamente,taletemperaturanonpuòesserecontrollata.Ilregolatoregeneralatemperaturadi
mandata di caldaia in funzione dell’incremento qui impostato e secondo il setpoint attuale di mandata. Adattare il tempo di azionamento del regolatore (pa-
rametri 834 e/o 1134) in funzione del tempo di corsa dell’attuatore (fare riferimento alle caratteristiche dell’attuatore stesso).
22.2 ATTIVAZIONE FUNZIONAMENTO SENZA UNITÀ AMBIENTE DIGITALE
Il funzionamento della caldaia senza unità ambiente digitale viene attivato tramite gli ingressi H1 e H3 del regolatore. Il regolatore è già impostato per un
funzionamento continuo della caldaia. Tuttavia è possibile collegare termostati ambiente (contatti normalmente aperti) ad H1 e/o H3 per abilitare il funziona-
mento su richiesta di calore. L’ingresso HX prescelto dovrà essere assoggettato ad alcune impostazioni tra cui la scelta dell’azione e la logica del contatto
(NO“NormalmenteAperto”oppureNC“NormalmenteChiuso”).Adesempio,perattivareilfunzionamentoinfunzionedellatemperaturaambiente,collegare
il contatto normalmente aperto del termostato ambiente all’ingresso H1 (vedere paragrafo “Gestione massima impianti”) e modificare i seguenti parametri:
Menù Specialista - Sottomenù Circuito riscaldamento CR1, CR2
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
Setup
5950 Funzione input H1Commutaz. regime
CR+ACSCommutaz. regime CR
5951 Logica contatto H1 Normalmente aperto Normalmente chiuso
N.B. La richiesta di calore avviene quando il contatto del termostato si chiude.
ÈpossibileagiresolamenteneiconfrontidiCR1,CR2oCRPmodificandoopportunamenteilparametro5950(vederelistacompletadeiparametri).
La stessa azione può essere svolta da H3 (vedere parametri 5960 e 5961).
Menù Messa in servizio (Specialista) - Sottomenù Configurazione
Attivare o disattivare CR1 e/o CR2 a seconda del tipo di impianto
- 27 -
IT
Elencodeiparametridaconfigurareperlagestionedell'impiantoACS.
Menù Messa in servizio (Specialista) - Sottomenù Configurazione
23. GESTIONE ACQUA CALDA SANITARIA (ACS)
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
Setup
5730 Sensore ACS B3 Sonda Sonda o Termostato in relazione al sensore impiegato
5731 Attuatore ACS Q3 Pompa carico Pompa di carico o valv. deviatrice in relazione al tipo di impianto
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
Setup
1610 Setpoint nominale 55°C Configurare a seconda delle esigenze
Menù Messa in servizio (Tutti) - Sottomenù ACS
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
Setup
1612 Setpoint ridotto 40°C Configurare a seconda delle esigenze
Menù Messa in servizio (Specialista) - Sottomenù ACS
Il funzionamento ACS segue il programma orario impostato secondo il “Programma orario 4/ACS” (vedere lista completa dei parametri).
23.1 CONTROLLO DELLA RICARICAL’attivazione del carico ACS per il mantenimento del setpoint nominale o ridotto avviene in relazione ad un opportuno differenziale di temperatura. Quando la tempe-ratura misurata dalla sonda ACS (B3) scende sotto il setpoint effettivo di un intervallo di temperatura maggiore a questo differenziale (parametro 5024), viene attivata la richiesta di calore per ACS fino al raggiungimento del setpoint stesso. Il differenziale in questione può essere modificato dal costruttore (è protetto da password).
Attenzione! Queste impostazioni devono essere eseguite solo da specialisti esperti (Installatore e Sevizio Assistenza Tecnica
Ferroli). I seguenti parametri sono protetti da password (interpellare il Sevizio Assistenza Tecnica Ferroli).
Menù OEM (Protetto da password) - Sottomenù Accumulo ACS
Prog N°(sul
display)
Presenzanel menu
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
CampoUnità
di misuraMin Max
Caldaia
5024 OEM Differenziale di commutazione 5 0 20 °C
23.2 CARICO ACCELERATO DELL’ACCUMULATORE ACSCome indicato nel paragrafo “INTERFACCIA AVS 37.294 - Selezione regime di riscaldamento ACS ”, si può attivare manualmente il carico accelerato dell’ac-cumulatore ACS dal setpoint ridotto premendo il pulsante dedicato per un tempo di 4 secondi. Il carico avviene per una sola volta fino al raggiungimento del setpoint nominale, dopodiché il riscaldamento avviene nuovamente in funzione del setpoint ridotto. La spinta di carico accelerato dell’accumulatore ACS può avvenire automaticamente in relazione all’impostazione del parametro 5070 (vedere tabella successiva).
Attenzione! Queste impostazioni devono essere eseguite solo da specialisti esperti (Installatore e Sevizio Assistenza Tecnica
Ferroli). I seguenti parametri sono protetti da password (interpellare il Sevizio Assistenza Tecnica Ferroli).
Menù OEM (Protetto da password) - Sottomenù Accumulo ACS
Prog N°(sul
display)
Presenzanel menu
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
CampoUnità
di misuraMin Max
Caldaia
5070 OEM Carico automatico acceleratoOff ¦ On
On -
Carico automatico accelerato. Il carico accelerato ACS può essere attivato manualmente o automaticamente. In tal caso, l’ACS viene riscaldato per una volta fino al punto di funzionamento nominale.
Off. Il carico accelerato ACS deve essere attivato manualmente.
On. Se la temperatura ACS scende al di sotto del punto di funzionamento ridotto (Linea di Funzionamento 1612) di almeno 2 volte il differenziale di commutazione
(Linea di Funzionamento 5024), verrà effettuata la ricarica accelerata fino al punto di funzionamento nominale dell’ACS (Linea di Funzionamento 1610).
Nota: Il carico automatico ACS accelerato funziona solamente quando la modalità di funzionamento dell’ACS è attivata.
- 28 -
24. CURVE CLIMATICHE - TEMPERATURA SCORREVOLEL’impiego della sonda esterna consente al generatore di funzionare a temperatura scorrevole cioè di alimentare gli impianti alla temperatura ottimale calcolata
inbaseallatemperaturaesterna.IlPannelloTHERMOEBMpermettediselezionarelacurvaclimaticapiùadattaperognicircuitodiriscaldamento.
La curva climatica selezionata si riferisce ad un setpoint ambiente di 20°C. Se viene modificato il setpoint ambiente la curva climatica si adatta automaticamente.
Le impostazioni di fabbrica sono:
Linea/Prog. 720 (CR1 miscelato): 1,5
Linea/Prog. 1020 (CR2 miscelato): 1,5
Linea/Prog. 1320 (CRP diretto): 1,5
20 10
100
90
80
70
60
50
40
30
0 -10 -20 -30
0,25
0,5
0,75
1
1,25
1,5
1,75
2
4 3,5 3 2,75 2,5 2,25
°C
°C
24.1. ADATTAMENTO CURVE CLIMATICHESi allegano alcune indicazioni per l’adattamento delle curve climatiche dei circuiti di riscaldamento.
Menù Utente finale - Sottomenù Circuito riscaldamento CR1, CR2, CRP
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
Setup
720, 1020, 1320 Pendenza curva caratteristica 1.5Modificare in base alle esigenze e alle caratteristiche dell’impianto
La curva di riscaldamento viene utilizzata per determinare il setpoint della temperatura di mandata opportuno al fine di mantenere un adeguato livello di
temperatura di mandata in funzione delle condizioni climatiche. La curva può essere adattata sfruttando alcuni parametri al fine di adeguare la produzione di
calore e la temperatura ambiente in funzione delle esigenze individuali.
Pendenza curva caratteristica. Se la temperatura ambiente non è corretta a fronte di basse temperature esterne ed è invece adeguata nel caso di temperature esterne elevate, si deve
apportare una modifica alla pendenza della curva. - Incremento della pendenza: Aumenta la temperatura di mandata, specialmente a fronte di basse temperature esterne. - Decremento della pendenza: Diminuisce la temperatura di mandata, specialmente a fronte di basse temperature esterne. Nota: La curva di riscaldamento di default si riferisce ad un setpoint ambiente di 20°C. Quando il setpoint ambiente viene modificato, la curve di riscalda-
mento si adatta automaticamente al nuovo valore.
Slittamento parallelo della curva caratteristica Lo slittamento parallelo della curva di riscaldamento è utilizzato per modificare in modo omogeneo la temperatura di mandata lungo l’intera scala della
temperatura esterna. In altre parole, se la temperatura ambiente è sempre troppo alta o troppo bassa, si deve effettuare una correzione della curva muo-vendola parallelamente all’interno nel grafico.
Adattamento della curva L’adattamento della curva di riscaldamento è utilizzato dal regolatore per adattare la curva in modo automatico alle condizioni climatiche prevalenti. In questo caso
unacorrezionedellapendenzae/ounoslittamentoparallelodellacurvacaratteristicanonsononecessari.Èpossibilesoloattivarliodisattivarli(“on”o“off”). Nota: Questa funzione ha senso se: -Vienecollegataalregolatorealmenoun’unitàambientedigitale; - L’ "Influenza ambiente" è impostata tra 1 e 99. - Non sono presenti valvole termostatiche nell’ambiente di riferimento (lo stesso in cui è collocato il sensore ambiente). Nel caso siano presenti,
devono essere regolate in completa apertura.
Menù Specialista - Sottomenù Circuito riscaldamento CR1, CR2, CRP
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
Setup
721, 1021, 1321 Slittamento curva 0Modificare in base alle esigenze e alle caratteristiche dell’impianto
726, 1026, 1326 Adattamento curva OffModificare in base alle esigenze e alle caratteristiche dell’impianto
- 29 -
IT
25. ANTICONDENSAPer gestire la messa a regime dell’impianto è consigliato installare una pompa anticondensa e la sonda di ritorno ad immersione “B7”, inserita in pozzetto
portasonda da posizionarsi sul tubo di ritorno a 3÷5 diametri a monte di eventuali innesti idraulici. In alternativa è possibile utilizzare una “sonda a bracciale”
con caratteristiche analoghe.
NOTA: Èammessoilmantenimentodellaminimatemperaturadiritornoincaldaia(ricircoloanticondensa)tramiteunavalvolamiscelatriceconcomandoa
trepunti.IntalcasolasondaB7andrebbeposizionatainunpuntodiverso.Deveessererilevatalatemperaturadell'acquamiscelatanellatubazione
diritornoincaldaia.AlpostodellapompaQ12,siutilizzeràunavalvolamiscelatricedicaratteristicheopportune,collegandolaall'uscitaY1/Y2oppure
Y5/Y6delregolatore.ImpostarelalineadiprogrammaLP6014("Funzionegruppomix1")oppureLP6015("Funzionegruppomix2")confunzione
"Controllo temperatura ritorno". Per approfondimenti si rimanda agli schemi idraulici del paragrafo "Esempi di schemi realizzabili (diagrammi parziali
e funzioni ausiliarie)" e al paragrafo "Visualizzazione e gestione dei parametri".
NOTA: L'utilizzo di una valvola miscelatrice per il mantenimento della temperatura di ritorno riduce necessariamente il numero massimo di
circuiti riscaldamento miscelati che possono essere gestiti (uno anziché due).
Q 12D
B 7
3 ÷
5 D
25.1 CONFIGURAZIONE DEL RICIRCOLO ANTICONDENSA
La gestione della pompa di ricircolo acqua in caldaia Q12 per il mantenimento della temperatura di ritorno della caldaia, soprattutto nelle fasi transitorie di
funzionamento,necessitadialcuneimpostazioni.ÈpossibileutilizzareunadelleusciteQXeconfigurarlacomealimentazioneoconsensofunzionamento
Pompa by-pass Q12. La sonda di misura della temperatura di ritorno B7 deve essere collegata ad uno degli ingressi BX libero, programmandolo in modo
opportuno. Per le programmazioni vedere tabella seguente e lista completa dei parametri.
Menù Messa in servizio (Specialista) - Sottomenù Configurazione
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
Setup
5890, 5891, 5892, 5894 Uscite relè QX1, QX2, QX3, QX4 Nessuna Pompa by-pass Q12
5930, 5931, 5932, 5933 Ingresso sonda BX1, BX2, BX3, BX4 Nessuna Sonda ritorno B7
N.B. Le uscite QX1, QX2, QX3 sono attive con tensione 230Vac mentre QX4 è un’uscita contatti puliti in scambio (FX4 è il comune).
Menù Specialista - Sottomenù Caldaia
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
Setup
2270 Setpoint ritorno minimo 8°CImpostare in relazione al tipo di
combustibile e alla minima temperatura desiderata di ritorno in caldaia
- 30 -
26. CONFIGURAZIONE PER LA GESTIONE DI GENERATORI IN CASCATA
La gestione di più generatori di calore in cascata necessita di alcune impostazioni, accessori e connessioni elettriche secondo lo schema di collegamento
generale. Per quello che riguarda il Regolatore Master, si deve collegare la sonda di mandata comune caldaie B10 ad uno degli ingressi BX disponibili. Si
collega anche la sonda temperatura esterna B9 all’ingresso dedicato.
Naturalmente ai pannelli Master e Slave si devono collegare anche la sonda di mandata della caldaia B2 e la pompa di circolazione caldaia Q1.
La comunicazione tra i diversi regolatori avviene tramite BUS LPB utilizzando i morsetti MB e DB (rispettivamente “Terra LPB“ e “Dati LPB“), rispettando le
polarità e le sezioni dei cavi elettrici in funzione della lunghezza (vedere tabella specifica). Ciascun regolatore della caldaia sarà individuato da un particolare
indirizzo che deve essere scelto durante la messa in servizio.
Nota: Qualora si decida di utilizzare una sola pompa di circolazione per l’intera cascata di caldaie Q25, questa dovrà essere collegata al Regolatore Master
(vedere lista completa dei parametri e lista completa delle configurazioni circuitali).
REGOLATORE MASTER
Menù Messa in servizio (Specialista) - Sottomenù Configurazione
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
Setup
5890, 5891, 5892, 5894 Uscite relè QX1, QX2, QX3, QX4 Nessuna Pompa caldaia Q1
5930, 5931, 5932, 5933 Ingresso sonda BX1, BX2, BX3, BX4 Nessuna Sonda mandata comune B10
N.B. Le uscite QX1, QX2, QX3 sono attive con tensione 230Vac mentre QX4 è un’uscita contatti puliti in scambio (FX4 è il comune).
Menù Messa in servizio (Specialista) - Sottomenù LPB
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
Setup
6600 Indirizzo apparecchio1
0 è per un apparecchio unico (stand alone)
1
REGOLATORE SLAVE
Menù Messa in servizio (Specialista) - Sottomenù Configurazione
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
Setup
5890, 5891, 5892, 5894 Uscite relè QX1,QX2, QX3, QX4 Nessuna Pompa caldaia Q1
N.B. Le uscite QX1, QX2, QX3 sono attive con tensione 230Vac mentre QX4 è un’uscita contatti puliti in scambio (FX4 è il comune).
Menù Messa in servizio (Specialista) - Sottomenù LPB
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
Setup
6600 Indirizzo apparecchio 1( 0 è per apparecchio stand alone)
2,3... 16 a seconda del numero di generatori
- 31 -
IT
26.1 CENNI STRATEGIA GESTIONE CALDAIE IN CASCATA
Di seguito si elencano alcuni parametri che possono essere utili per la gestione efficiente del collegamento dei generatori in cascata.
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
3532 Blocco riavvio
3533 Ritardo all’accensione
3540 Sequenza automatica della sorgente
3541 Esclusione sequenziale automatica della sorgente
3544 Sorgente principale
Blocco riavvio Consente di evitare che una sorgente di calore disattivata venga attivata nuovamente prima di un intervallo di tempo definito. Ciò consente di evitare azioni di commutazione delle sorgenti di calore troppo frequenti e garantisce condizioni di funzionamento stabili per l’impianto.
Ritardo all’accensione Una corretta impostazione del ritardo di accensione assicura che le condizioni operative dell’impianto si mantengano stabili. Consente di evitare frequenti commutazioni delle sorgenti di calore. Con le richieste ACS, il periodo di ritardo viene fissato ad 1 minuto
Sequenza automatica della sorgente Consente di impostare l’ordine di priorità tra le diverse sorgenti:
- Ordine fisso: L’impostazione − − − consente di impostare un ordine fisso di commutazione. In tal caso, la sorgente di calore principale può essere selezionata mediante la linea programma 3544 e le rimanenti sorgenti di calore verranno quindi
accese o spente nello stesso ordine degli indirizzi del dispositivo LPB.
- Ordine basato sul numero di ore di funzionamento È consentito modificare secondo le esigenze il numero di ore oltre il quale viene scambiata la priorità di accensione dei generatori. L'impostazionedifabbricaè500ore.Loscambiodiprioritàavvienesecondol'ordinediindirizzodeidispositivi.
Esclusione sequenziale automatica della sorgente Può essere utilizzata solamente in combinazione con il parametro “Sequenza automatica della sorgente” (3540). Consente di escludere dalla commutazione automatica la prima e/o l’ultima sorgente di calore.
Sorgente principale Può essere utilizzata solamente in combinazione con il parametro “Sequenza automatica della sorgente” (3540). La sorgente di calore definita come sorgente di calore principale è sempre la prima ad essere accesa e l’ultima ad essere spenta. Le altre sorgenti di calore vengono accese e spente nello stesso ordine degli indirizzi del dispositivo LPB.
Menù specialista - Sottomenù Generatori di calore in cascata
27. MANTENIMENTO IN TEMPERATURA DELLA MANDATA SENZA SONDE DI TEMPERATURA AMBIENTE/ESTERNAIn taluni casi si richiede il mantenimento in temperatura di un anello idraulico di distribuzione del calore senza alcuna richiesta esterna di calore o termostati
ambiente o sonde esterne. La produzione di calore può essere affidata ad un solo generatore (configurazione “stand-alone”) oppure a più generatori di calore
collegati in cascata (configurazione “in cascata”). In quest’ultimo caso valgono le considerazioni fatte nel paragrafo “FUNZIONAMENTODIGENERATORIIN
CASCATA”. I circuiti CR1, CR2, se non utilizzati, devono essere disattivati (LP5710 e LP5715).
A tale scopo si possono sfruttare gli ingressi H1 e H3 configurando i parametri che competono come indicato nella seguente tabella:
Menù Messa in servizio (Specialista) - Sottomenù Configurazione
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
Setup
5950, 5960 Funzione input H1, H3Commutaz. regime
CR+ACSSetpoint minimo mandata
5951, 5961 Logica contatto H1, H3 Normalmente aperto Normalmente aperto
5952, 5962 Setpoint minimo mandata H1, H3 70°CModificare in base alle esigenze
e ai limiti d’impianto
Si devono collegare interruttori agli ingressi H1 e/o H3.La chiusura dei contatti degli interruttori attiveranno la produzione di calore.
ÈpossibileattivarelaproduzionecontinuadicalorecollegandodeiponticelliagliingressiH1e/oH3.
Èsufficientecollegarel'interruttoreoilponticelloaunosolodeidueingressisummenzionatiperattivareilsistema.
- 32 -
28.1 INTEGRAZIONE SOLARE TERMICO CON UN SOLO COLLETTORE
B31
B3
B6
Q5
Menù Messa in servizio (Specialista) - Sottomenù Configurazione
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
Setup
5890, 5891, 5892, 5894 Uscite relè QX1,QX2, QX3, QX4 Nessuna Pompa collettore Q5
5930, 5931, 5932, 5933 Ingresso sonda BX1,BX2, BX3, BX4 Nessuna Sonda collettore B6
5930, 5931, 5932, 5933 Ingresso sonda BX1,BX2, BX3, BX4 Nessuna Sonda ACS B31
N.B. Le uscite QX1, QX2, QX3 sono attive con tensione 230Vac mentre QX4 è un’uscita contatti puliti in scambio (FX4 è il comune).
28. CONFIGURAZIONE PER L'INTEGRAZIONE DEL SOLARE TERMICOSi allegano le configurazioni circuitali e la lista dei parametri da configurare per la gestione e l’integrazione di alcuni tipi di impianto a riscaldamento solare.
Si raccomanda di posizionare le sonde e le pompe di circolazione necessarie come indicato nelle figure allegate.
Menù Messa in servizio (Specialista) - Sottomenù Configurazione
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
Setup
5840 Elemento di controllo solare Pompa caricoPompa di carico o valvola deviatrice in
relazione al tipo di impianto solare
5841 Scambiatore solare esterno InsiemeConfigurare in base alle esigenze e alle
caratteristichedell'impianto
Elemento di controllo solare Al posto della pompa del collettore e delle valvole deviatrici, per integrare i serbatoi di accumulo è possibile gestire l’impianto solare con le pompe di carico
dell’impianto di generazione e gestione del calore. Se si utilizza una valvola deviatrice, si può utilizzare un solo scambiatore di calore alla volta. In questo caso è ammesso solamente il funzionamento alternato. Se si utilizza una pompa carico, si possono utilizzare contemporaneamente tutti gli scambiatori di calore. In questo caso è possibile il funzionamento in
parallelo o alternato.
Scambiatore solare esterno Nel caso di impianti solari dotati di due serbatoi di accumulo, è necessario indicare se lo scambiatore di calore esterno verrà utilizzato per l’ACS e per il
serbatoio di riserva, oppure esclusivamente per uno dei due.
- 33 -
IT
28.3 INTEGRAZIONE SOLARE TERMICO CON DUE COLLETTORI
B31
B3
Q5 Q16
B6 B61
Menù Messa in servizio (Specialista) - Sottomenù Configurazione
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
Setup
5890, 5891, 5892, 5894 Uscite relè QX1, QX2, QX3, QX4 Nessuna Pompa collettore Q5
5890, 5891, 5892, 5894 Uscite relè QX1, QX2, QX3, QX4 Nessuna Pompa collettore 2 Q16
5930, 5931, 5932, 5933 Ingresso sonda BX1, BX2, BX3, BX4 Nessuna Sonda collettore B6
5930, 5931, 5932, 5933 Ingresso sonda BX1, BX2, BX3, BX4 Nessuna Sonda ACS B31
5930, 5931, 5932, 5933 Ingresso sonda BX1, BX2, BX3, BX4 Nessuna Sonda collettore 2 B61
N.B. Le uscite QX1, QX2, QX3 sono attive con tensione 230Vac mentre QX4 è un’uscita contatti puliti in scambio (FX4 è il comune).
28.2 INTEGRAZIONE SOLARE TERMICO CON UN COLLETTORE E UN SERBATOIO DI RISERVA SEPARATO
B3
Q5
B31
B6
Menù Messa in servizio (Specialista) - Sottomenù Configurazione
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
Setup
5890, 5891, 5892, 5894 Uscite relè QX1,QX2, QX3, QX4 Nessuna Pompa collettore Q5
5930, 5931, 5932, 5933 Ingresso sonda BX1,BX2, BX3, BX4 Nessuna Sonda collettore B6
5930, 5931, 5932, 5933 Ingresso sonda BX1,BX2, BX3, BX4 Nessuna Sonda ACS B31
N.B. Le uscite QX1, QX2, QX3 sono attive con tensione 230Vac mentre QX4 è un’uscita contatti puliti in scambio (FX4 è il comune).
- 34 -
Per le programmazioni e approfondimenti vedere la lista completa
dei parametri e/o contattare il servizio assistenza tecnica Ferroli.
28.5 PROTEZIONE ANTIGELO COLLETTORE
Quando sussiste il rischio di gelo in corrispondenza del collettore solare, la pompa del collettore viene attivata per evitare il congelamento del termovettore.
Menù specialista - Sottomenù Collettore solare
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
3840 Protezione antigelo collettore
28.6 PROTEZIONE SURRISCALDAMENTO COLLETTORE
In caso di rischio di surriscaldamento del collettore, il carico dell’accumulatore (attivazione pompa collettore) viene proseguito al fine di ridurre il calore in
eccesso. Una volta raggiunta la temperatura di sicurezza nell’accumulatore, il caricamento viene interrotto.
Menù specialista - Sottomenù Collettore solare
Per le programmazioni e approfondimenti vedere la lista completa
dei parametri e/o contattare il servizio assistenza tecnica Ferroli.
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
3850 Protezione antisurriscaldamento collettore
Nota: TLmin si riferisce ai parametri 3812, 3815 (anche 3818 “Minima temperatura di riscaldamento piscina”, non trattato in questo manuale).
Per le programmazioni e approfondimenti vedere la lista completa
dei parametri e/o contattare il servizio assistenza tecnica Ferroli.
28.4 CENNI SULLE IMPOSTAZIONI DI CARICO DELL’ACCUMULATORE SANITARIO TRAMITE SCAMBIATORE DI INTEGRAZIONE SOLARE TERMICO
Regolatore di carico (dT)
Per caricare l’accumulatore del sanitario tramite scambiatore di calore, è richiesto un differenziale di temperatura tra il collettore e l’accumulatore e deve essere rag-
giunta la temperatura minima di carico. Si osservi la lista dei parametri e la figura seguente per adattare il comportamento del sistema in base alle proprie esigenze.
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
3810 DifferenzialetemperaturacollettoreON
3811 DifferenzialetemperaturacollettoreOFF
3812 Minima temperatura di riscaldamento bollitore ACS
3815 Minima temperatura di risc. serbatoio di accumulo
Menù specialista - Sottomenù Collettore solare
ON
OFF
SdOn
SdOff
TSp
TLmin
t
TTkol
ON
OFF
SDon
SDoff
BX
t
TTkx
LegendaT Tkol Temperatura collettoreON/OFF Pompa collettoreSdOn DifferenzialetemperaturaONSdOff DifferenzialetemperaturaOFFTSp Temperatura accumulatoreTLmin Temperatura minima di ricarica al serbatoio ACS/buffer/piscina
- 35 -
IT
29.1 MODALITÀ DI FUNZIONAMENTOMenù specialista - Sottomenù Caldaia a combustibile solido
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
Setup
4102 Blocco altre fonti di riscaldamento On On/Offasecondadelleesigenze
Blocco altre fonti di riscaldamento Quando viene messa in funzione la caldaia a combustibile solido, le altre sorgenti di calore, quali le caldaie a olio / gas, verranno bloccate. Il blocco si verifica non appena la temperatura della caldaia aumenta ad un livello tale da far presagire il superamento della temperatura di confronto. Questa funzione di anticipo consente alle sorgenti di calore bloccate di concludere l’operazione di arresto delle pompe prima dell’attivazione della pompa
caldaia a combustibile solido. Inoltre, nel caso di un camino comune, consente di accertarsi di mettere in funzione una sola caldaia alla volta.
29.2 SETPOINTMenù specialista - Sottomenù Caldaia a combustibile solido
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
Setup
4110 Setpoint minimo 40°C Impostare in base alle esigenze
Setpoint minimo Qualora il parametro 4133 “Temperatura comparativa” (vedere tabella successiva) è impostato come “Setpoint min”, la pompa della caldaia Q10 verrà
messa in funzione solo quando la temperatura della caldaia a combustibile solido ha raggiunto un livello minimo di temperatura definito da questo para-metro, più un opportuno differenziale (parametri 4130 e 4131).
29.3 CONTROLLO CALDAIA / BRUCIATOREMenù specialista - Sottomenù Caldaia a combustibile solido
Prog N°(sul display)
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
Setup
4130 DifferenzialeditempON 8°C Impostare in base alle esigenze
4131 DifferenzialeditempOFF 4°C Impostare in base alle esigenze
4133 Temperatura comparativa Setpoint minimoModificare in base alle esigenze e alle caratteristiche dell’impianto
Regolatore differenziale (dT) Affinché entri in funzione la pompa della caldaia Q10, è richiesto un differenziale di temperatura sufficientemente grande tra la temperatura della caldaia
e la temperatura di confronto (questo differenziale è definito per mezzo dei parametri 4130 e 4131).
ON
OFF
SdOn
SdOff
TSp
TLmin
t
TTkol
ON
OFF
SDon
SDoff
BX
t
TTkx
LegendaT Tkx Temperatura caldaiaBx Valore effettivo della temperatura di confrontoON/OFF Pompa della caldaiaSDon DifferenzialetemperaturaONSDoff DifferenzialetemperaturaOFF
29. CALDAIA A COMBUSTIBILE SOLIDOSi allega la lista dei parametri ed alcune indicazioni per la corretta gestione ed integrazione all’impianto di generazione di calore di una caldaia a combustibile solido.
Per le programmazioni e approfondimenti vedere la lista completa
dei parametri e/o contattare il servizio assistenza tecnica Ferroli.
Q10
B22 T
- 36 -
La tabella riporta:
-Tuttelelinee/parametri(sulDisplayvisualizzaticonProg.No)diogniSottomenu;
- In quale Menu, si trova ogni Sottomenu (T=Tutti;M=Messainservizio(assistenzatecnica);S=Specialista(installatore));
- La funzione di ogni parametro, la sua Impostazione di fabbrica e il campo di regolazione.
Nota: Le Linee/Parametri sono visualizzati sul display con "Prog. NOFF" e abbreviati con "LP.+ NOFF" (es. LP5770)
Prog N°(sul
display)
Presenzanel menu
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
CampoUnità
di misuraMin Max
Ora e data1 T ora/minuti - 0:00 23:59 hh:mm
2 T Mese, giorno - 01.01 31.12 gg.mm
3 T Anno - 2004 2099 aaaa
5 S Inizio ora legale 25.03 01.01 31.12 gg.mm
6 S Fine ora legale 25.10 01.01 31.12 gg.mmUnità di comando
20 TLinguaEN ¦ Deutsch - D ¦ FR ¦ IT ¦ NL ¦ ES ¦ PO ¦ DK ¦ SU ¦ S ¦
Deutsch (Tedesco) -
22 S InformazioneTemporanea ¦ Permanente
Temporanea -
26 S Blocco comandiOff ¦ On
Off -
27 S Blocco ProgrammazioneOff ¦ On
Off -
28 M-S Regolazione direttaSalvataggio automatico ¦ Salvataggio con conferma
Salvataggio con conferma -
29 M-S Unità di comando°C, bar ¦ °F, PSI
°C, bar -
44 M-SFunzionamento CR2Insieme a CR1 ¦ Indipendente
Insieme a CR1 -
46 M-SFunzionamento CR3/PInsieme a CR1 ¦ Indipendente
Insieme a CR1 -
70 S Versione software 06.1 T 99.9 -
Radio (non utilizzato)
Programma orario CR 1
500 T PreselezioneLu-Do ¦ Lu-Ve ¦ Sa-Do ¦ Lu ¦ Ma ¦ Me ¦ Gio ¦ Ve ¦ Sa ¦ Do
Lu - Do
501 T 1°periodoOn 6:00 00:00 24:00 hh:mm
502 T 1°periodoOff 22:00 00:00 24:00 hh:mm
503 T 2°periodoOn --:-- 00:00 24:00 hh:mm
504 T 2°periodoOff --:-- 00:00 24:00 hh:mm
505 T 3°periodoOn --:-- 00:00 24:00 hh:mm
506 T 3°periodoOff --:-- 00:00 24:00 hh:mm
516 T Valori standardNo ¦ Si
No
Programma orario CR 2520.....536
T (stesso programma orario del CR1)
30. VISUALIZZAZIONE E GESTIONE DEI PARAMETRI
- 37 -
IT
Prog N°(sul
display)
Presenzanel menu
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
CampoUnità
di misuraMin Max
Programma orario 3/CRP540.....556
T (stesso programma orario del CR1)
Programma orario 4/ACS550.....576
T (stesso programma orario del CR1)
Programma orario 5600.....616
T (stesso programma orario del CR1)
Vacanze CR 1
641 TPreselezionePeriodo 1 ¦ Periodo 2 ¦ Periodo 3 ¦ Periodo 4 ¦ Periodo 5 ¦ Periodo 6 ¦ Periodo 7 ¦ Periodo 8
Periodo 1
642 T Inizio --:-- 01.01 31.12 gg.mm
643 T Fine --:-- 01.01 31.12 gg.mm
648 T Livello operativoProtezione antigelo ¦ Ridotto
Protezione antigelo
Vacanze CR 2651.....658
T (stesso programma orario del CR1)
Vacanze CRP661.....668
T (stesso programma orario del CR1)
Circuito riscaldamento 1710 T Setpoint comfort 20.0 LP716 LP716 °C
712 T Setpoint ridotto 16 LP714 LP710 °C
714 T Setpoint protezione antigelo 10.0 4 LP712 °C
716 S Setpoint comfort max 35.0 LP710 35 °C
720 T Pendenza curva caratteristica 1.50 0.10 4.00 °C
721 S Slittamento curva 0.0 -4.5 4.5 °C
726 S Adattamento curva Off ¦ On
Off -
730 T Valore limite commutazione estate/inverno 18 ---/8 30 °C
732 S Valore limite riscaldamento diurno -3 ---/-10 10 °C
740 M-S Setpoint di mandata min 8 8 LP741 °C
741 M-S Setpoint di mandata max 80 LP740 95 °C
750 S Influenza ambiente 20 ---/1 100 %
760 S Limitazione temperatura ambiente 1 ---/0.5 4 °C
770 S Riscaldamento accellerato 5 ---/0 20 °C
780 S Riduzione accellerataOff ¦ Fino a setpoint ridotto ¦ Fino a setpoint antigelo
Fino a Setpoint ridotto -
790 S Ottimizzazioneall’accensione 0 0 360 min
791 S OttimizzazioneallospegnimentoMax 0 0 360 min
800 S Inizio aumento setpoint ridotto --- ---/-3 10 °C
801 S Fine aumento setpoint ridotto -15 -30 LP800 °C
820 S Protezione circuito pompaOff ¦ On
On -
- 38 -
Prog N°(sul
display)
Presenzanel menu
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
CampoUnità
di misuraMin Max
830 S Boost valvola miscelatrice 5 0 50 °C
832 S Tipo attuatore2 punti ¦ 3 punti
3 punti -
833 S Differenziale commutazione 2 pos 2 0 20 °C
834 S Tempo di corsa attuatore 120 30 873 s
850 T
Funzione massettoOff ¦ Riscaldamento funzionale ¦ Riscaldamento pronto posa ¦ Risc. funzionale/pronto posa ¦ Risc. pronto posa/funzionale ¦ Manuale
Off -
851 T Setpoint massetto manuale 25 0 95 °C
861 S Dissipazione del calore in eccessoOff ¦ Regime riscaldamento ¦ Sempre
Sempre -
870 S Con bollitoreNo ¦ Si
Si -
872 S Con regolatore primario/pompa di sistemaNo ¦ Si
Si -
882 S Velocità pompa - minima 100 0 100 %
883 S Velocità pompa - massima 100 0 100 %
900 S Commutazione regimeNessuna ¦ Protezione ¦ Ridotto ¦ Comfort ¦ Automatico
Modalità protezione -
Circuito di riscaldamento 21010 T Setpoint comfort 20.0 LP716 LP716 °C
1012 T Setpoint ridotto 16 LP714 LP710 °C
1014 T Setpoint protezione antigelo 10.0 4 LP712 °C
1016 S Setpoint comfort max 35.0 LP710 35 °C
1020 T Pendenza curva caratteristica 1.50 0.10 4.00 °C
1021 S Slittamento curva 0.0 -4.5 4.5 °C
1026 S Adattamento curva Off ¦ On
Off -
1030 T Valore limite commutazione estate/inverno 18 ---/8 30 °C
1032 S Valore limite riscaldamento diurno -3 ---/-10 10 °C
1040 M-S Setpoint di mandata min 8 8 LP741 °C
1041 M-S Setpoint di mandata max 80 NP740 95 °C
1050 S Influenza ambiente 20 ---/1 100 %
1060 S Limitazione temp. ambiente 1 ---/0.5 4 °C
1070 S Riscaldamento accellerato 5 ---/0 20 °C
1080 S RIduzione accelerataOff ¦ Fino a setpoint ridotto ¦ Fino a setpoint antigelo
Fino a Setpoint ridotto -
1090 S Ottimizzazioneall’accensione 0 0 360 min
1091 S OttimizzazioneallospegnimentoMax 0 0 360 min
1100 S Inizio aumento setpoint ridotto --- ---/-3 10 °C
1101 S Fine aumento setpoint ridotto -15 -30 LP800 °C
1120 S Protezione pompa CROff ¦ On
On -
1130 S Differenziale di maggiorazione Setpoint di confronto 5 0 50 °C
1132 S Tipo attuatore2 punti ¦ 3 punti
3 punti -
1133 S Differenziale commutazione 2 2 0 20 °C
1134 S Tempo di corsa attuatore 120 30 873 s
1150 M-SFunzione massettoOff ¦ Riscaldamento funzionale ¦ Risc. pronto posa ¦ Risc. funzionale/pronto posa ¦ Risc. pronto posa/funzionale
Off -
- 39 -
IT
Prog N°(sul
display)
Presenzanel menu
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
CampoUnità
di misuraMin Max
1151 M-S Setpoint massetto manuale 25 0 95 °C
1161 S Dissipazione del calore in eccessoOff ¦ Regime riscaldamento ¦ Sempre
Sempre -
1170 S Con bollitoreNo ¦ Si
Si -
1172 S Con regolatore primario/pompa di sistemaNo ¦ Si
Si -
1182 S Velocità pompa - minima 100 0 100 %
1183 S Velocità pompa - massima 100 0 100 %
1200 S Commutazione regimeNessuna ¦ Protezione ¦ Ridotto ¦ Comfort ¦ Automatico
Modalità protezione -
Circuito di riscaldamento CRP
1300 T Modalità operativaProtezione ¦ Automatico ¦ Ridotto ¦ Comfort
Modalità automatico -
1310 T Setpoint comfort 20.0 LP716 LP716 °C
1312 T Setpoint ridotto 16 LP714 LP710 °C
1314 T Setpoint protezione antigelo 10.0 4 LP712 °C
1316 S Setpoint comfort max 35.0 LP710 35 °C
1320 T Pendenza curva caratteristica 1.50 0.10 4.00 °C
1321 S Slittamento curva 0.0 -4.5 4.5 °C
1326 S Adattamento curva Off ¦ On
Off -
1330 T Limite commutazione estate/inverno 18 ---/8 30 °C
1332 M-S Limite riscaldamento 24 ore -3 ---/-10 10 °C
1340 M-S Setpoint temperatura di mandata min 8 8 LP741 °C
1341 M-S Setpoint temperatura di mandata max 80 NP740 95 °C
1350 S Influenza ambiente 20 ---/1 100 %
1360 S Limitazione temp. ambiente 1 ---/0.5 4 °C
1370 S Riscaldamento accellerato 5 ---/0 20 °C
1380 S RIduzione accelerataOff ¦ Fino a setpoint ridotto ¦ Fino a setpoint antigelo
Fino a Setpoint ridotto -
1390 S Ottimizzazioneall’accensione 0 0 360 min
1391 S Ottimizzazioneallospegnimento 0 0 360 min
1400 S Inizio aumento setpoint ridotto --- ---/-3 10 °C
1401 S Fine aumento setpoint ridotto -15 -30 LP800 °C
1420 S Antisurriscaldamento pompa CROff ¦ On
On -
1450 M-SFunzione massettoOff ¦ Riscaldamento funzionale ¦ Risc. pronto posa ¦ Risc. funzionale/pronto posa ¦ Manuale
Off -
1451 M-S Setpoint massetto manuale 25 0 95 °C
1455 ISetpoint massetto attualeGiorno massetto attuale
0 0 95 °C
1461 S Dissipazione smaltimento del calore in eccessoOff ¦ Modalità di riscaldamento ¦ Sempre
Sempre -
1470 S Con bollitoreNo ¦ Si
Si -
1472 S Con regolatore primario/pompa di sistemaNo ¦ Si
Si -
1482 S Velocità pompa - minima 100 0 100 %
1483 S Velocità pompa - massima 100 0 100 %
1500 S Commutazione regimeNessuna ¦ Protezione ¦ Ridotto ¦ Comfort ¦ Automatico
Modalità protezione -
- 40 -
ACS
1610 T Setpoint nominale 55 LP 1612LP 1614
OEM°C
1612 S Setpoint ridotto 40 8 LP 1610 °C
1620 S ConsensoProgram. orario 4/CR ¦ Program. orario CR ¦ 24 ore/giorno
Program. orario CR
1630 M-SPriorità di carico Assoluta ¦ Slittante ¦ Nessuna ¦ Circuito miscelatore slittante/circuito diretto assoluto
Circuito miscelato slittante/circuito diretto assoluto
-
1640 S Funzione antilegionellaOff ¦ Periodica ¦ Giorno fisso della settimana
Giorno fisso della settimana
-
1641 S Funzione antilegionella 3 1 7 Giorno
1642 SFunzione antilegionella giornaliera Lunedì ¦ Martedì ¦ Mercoledì ¦ Giovedì ¦ Venerdì ¦ Sabato ¦ Domenica
Lunedì
1644 S Orariofunzioneantilegionella --- ---/ 00:00 23:50 hh:mm
1645 S Setpoint funzione antilegionella 65 55 95 °C
1646 S Durata funzione antilegionella 30 ---/10 360 min
1647 S Pompa di circolazione funz. antilegionellaOff ¦ On
On -
1660 SConsenso pompa ricircolazioneProgramma orario 3/CRP ¦ Consenso ACS ¦ Programma orario 4/ACS
Consenso ACS -
1661 S Intermittenza pompa di circolazioneOff ¦ On
On -
1663 S Setpoint di ricircolazione 45 8 80 °C
Pompa Hx
2010 S H1 dissipazione del calore in eccessoOff ¦ On
On -
2012 S H1 con accumuloNo ¦ Si
Si -
2014 S H1 regolatore prim/pompa di sistemaNo ¦ Si
Si -
2035 S H2 dissipazione del calore in eccessoOff ¦ On
On -
2037 S H2 con accumuloNo ¦ Si
Si -
2039 S H2 regolatore prim/pompa di sistemaNo ¦ Si
Si -
2046 S H3 dissipazione del calore in eccessoOff ¦ On
On
2048 S H3 con accumuloNo ¦ Si
Si
2050 S H3 regolatore prim/pompa di sistemaNo ¦ Si
Si
Piscina2055 T Setpoint riscaldamento solare 26 8 80 °C
2056 T Setpoint riscaldamento sorgente non solare 22 8 80 °C
2065 S Priorità di riscaldamento solareNo ¦ Si
No
2080 S Con collegamento solareNo ¦ Si
Si
Regolatore primario di sistema
2150 T Regolatore primario/pompa di sistemaPrima accumulo ¦ cisterna di deposito buffer ¦ Dopo
Dopo accumulo -
Prog N°(sul
display)
Presenzanel menu
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
CampoUnità
di misuraMin Max
- 41 -
IT
Caldaia2203 S Consenso sotto temp. Est. --- ---/-50 50 °C
2205 S Con modo ecoOff ¦ On ACS ¦ On
Off
2208 S Carico completo bollitoreOff ¦ On
Off
2210 S Setpoint minimo 40LP 2211
OEM
Controllomanualesetpoint
°C
2212 S Setpoint massimo 80Controllomanualesetpoint
LP 2213OEM
°C
2270 S Setpoint ritorno minimo 8 8 95 °C
2330 S Outputnominale 50 0 1000 kW
2331 S Outputstadiobase 30 0 1000 kW
2340 SSequenza auto cascata 2x1Frequenza scambio della caldaia in cascata 2x1
500 ---/10 990 h
Generatori di calore in cascata3532 S Blocco riavvio 300 0 1800 s
3533 S Ritardoall'accensione 5 0 120 min
3540 S Sequenza automatica della sorgente 500 ---/10 990 h
3541 S Esclusione sequenziale automatica della sorgentenessuno ¦ primo ¦ ultimo ¦ primo e ultimo
Nessuno
3544 S Sorgente principaleFonte 1 ¦ Fonte 2 ¦ ... ¦ Fonte 16
Fonte 1
3560 S Setpoint della temperatura minima di ritorno 8 8 95 °C
Collettore solare3810 S DifferenzialetemperaturacollettoreON 8 0 40 °C
3811 S DifferenzialetemperaturacollettoreOFF 4 0 40 °C
3812 S Minima temperatura di riscaldamento bollitore ACS --- ---/8 95 °C
3815 S Minima temperatura di riscaldamento serbatoio di accumulo --- ---/8 95 °C
3818 S Minima temperatura di riscaldamento piscina --- ---/8 95 °C
3822 S Impostazione priorità del riscaldamento solarenessuno ¦ bollitore acqua sanitaria ¦ serbatoio d'accumulo
Bollitore acqua sanitaria
3825 S Tempo di riscaldamento del circuito prioritario --- ---/2 60 min
3826 S Tempo di attesa del circuito prioritario 5 1 40 min
3827 S Tempo di attesa funzionamento del parallelo --- ---/0 40 min
3828 S Tempo di ritardo attivazione pompa secondaria 60 0 600 s
3831 S Tempo minimo funz. pompa collettore 20 5 120 s
3834 S Funzione gradiente per avvio pompa collettore --- ---/1 20 min/ °C
3840 S Protezione antigelo collettore --- ---/-20 5 °C
3850 S Protezione antisurriscaldamento collettore --- ---/30 350 °C
3860 S Evaporatore fluido termovettore --- ---/60 350 °C
3870 S Minimo numero di giri della pompa 40 0 100 %
3871 S Massimo numero di giri della pompa 100 0 100 %
3880 S Tipo di protezione antigelo-glicolenessuno ¦ etilenico ¦ polietilenico ¦ etilenico e polietilenico
Nessuno
3881 S Concentrazione antigelo 30 1 100 %
3884 S Flusso della pompa 200 0 1500 l/h
Prog N°(sul
display)
Presenzanel menu
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
CampoUnità
di misuraMin Max
- 42 -
Caldaia a combustibile solido
4102 S Blocco altre fonti di riscaldamentoOff ¦ On
On -
4110 S Setpoint minimo 40 8 120 °C
4130 S DifferenzialeditempON 8 1 40 °C
4131 S DifferenzialeditempOFF 4 0 40 °C
4133 STemperatura comparativaB3 sensore acqua sanitaria ¦ B31 sensore acqua sanitaria ¦ B4 sensore accumulo ¦ B41 sensore accumulo ¦ Setpoint temp flusso ¦ Setpoint min.
Setpoint minimo
Accumulo di deposito buffer
4720 S Blocco generazione automaticaNessuno ¦ Con B4 ¦ Con B4 e B42/41
con B4
4722 S Diff. temperatura accumulo circuito riscaldamento -5 -20 20 °C
4724 S Temperatura minima del serbatoio in modalità riscaldamento --- ---/8 95 °C
4750 S Temperatura di riscaldamento massima 80 8 95 °C
4755 S Temperatura di raffreddamento 60 8 95 °C
4756 S Raffreddamento ACS/CR riscaldamento Off ¦ On
Off -
4757 S Raffreddamento per circolazione su collettoriOff ¦ Estate ¦ Sempre
Off
4783 S Con integrazione solareNo ¦ Si
No
4790 S DifftemperaturaONperdeviazionesulritorno 10 0 40 °C
4791 S DifftemperaturaOFFperdeviazionesulritorno 5 0 40 °C
4795 S Temperatura di confronto su deviazione ritornoB4 ¦ B41 ¦ B42
B42
4796 S OpzionesudeviazioneritornoAumento di temp. ¦ Diminuzione di temp.
Aumento di temperatura
4800 S Setpoint di riscaldamento parziale --- ---/8 95 °C
Accumulo ACS5020 S Incremento Setpoint mandata 16 0 30 °C
5021 S Boost trasferimento 8 0 30 °C
5022 S Tipo caricocon B3 ¦ con B3/B31 ¦ con B3, legion B3/B31
con B3/B31 -
5050 S Temperatura massima di carico 80 8LP 5051
OEM°C
5055 S Temp. di raffreddamento 80 8 95 °C
5056 S Raffreddamento caldaia / CROff ¦ On
Off -
5057 S Raffreddamento collettoreOff ¦ Estate ¦ Sempre
Off -
5060 S Regime resistenza elettricaSostituzione ¦ Estate ¦ Sempre
Sostituzione -
5061 SFunzionamento resistenza elettrica24 ore/giorno ¦ Consenso ACS ¦ Programma orario 4/ACS
Consenso ACS -
5062 S Controllo resistenza elettricaTermostato esterno ¦ Sensore ACS
Sensore ACS -
5085 S Smaltimento eccesso caloreOff ¦ On
On -
5090 S Con bollitoreNo ¦ Si
No -
5092 S Con regolatore primario/pompa di sistemaNo ¦ Si
No -
5093 S Con integratore solareNo ¦ Si
Si -
5101 S Velocità pompa minima 40 0 100 %
5102 S Velocità pompa massima 100 0 100 %
Prog N°(sul
display)
Presenzanel menu
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
CampoUnità
di misuraMin Max
- 43 -
ITRiscaldatore istantaneo ACS5406 S Minimo differenziale di Setpoint 4 0 20 °C
5544 S Tempo di apertura attuatore 60 7.5 480 s
Configurazione
5710 M-S Circuito riscaldamento 1Off ¦ On
On -
5715 M-S Circuito riscaldamento 2Off ¦ On
Off -
5730 M-S Sensore ACS B3Sonda ¦ Termostato
Sonda -
5731 M-S Attuatore ACS Q3Nessuna richiesta carico ¦ Pompa carico ¦ Valvola deviatrice
Pompa carico -
5736 M-S Circuito separato ACSOff ¦ On
Off -
5770 M-STipo di generatore1 stadio ¦ 2 stadi ¦ Mod. 3 punti ¦ Modulante UX ¦ Senza sonda caldaia ¦ cascata 2 x 1
2 stadi -
5840 M-S Elemento di controllo solarePompa carico ¦ Valvola deviatrice
Pompa carico -
5841 M-S Scambiatore solare esternoInsieme ¦ Serbatoio ACS ¦ Buffer
Insieme -
5890 M-S
Uscita relè QX1Nessuna ¦ Pompa di ricircolo Q4 ¦ Resistenza elettrica ACS K6 ¦ Pompa collettore Q5 ¦ Pompa H1 Q15 ¦ Pompa caldaia Q1 ¦ Pompa by-pass Q12 ¦ Uscita allarme K10 ¦ Velocità pompa CR1 Q21 ¦ Velocità pompa CR2 Q22 ¦ Velocità pompa CRP Q23 ¦ Pompa CRP Q20 ¦ Pompa H2 Q18 ¦ Pompa sistema Q14 ¦ Valvola deviatrice Y4 ¦ Pompa caldaia a legna Q10 ¦ Programma orario 5 K13 ¦ Valvola ritorno buffer Y15 ¦ Pompa scambiatore ester-no solare K9 ¦ Elem. controllo solare bollitore K8 ¦ Elem. controllo solare piscina K18 ¦ Pompa collettore 2 Q16 ¦ H3 pompa Q19 ¦ Relè fumi K17 ¦ Ventil comb assistita K30 ¦ Pompa cascata Q25 ¦ Pompa trasf bollitore Q11 ¦ Pompa mix ACS Q35 ¦ Pompa interm. ACS Q33 ¦ Richie-sta calore K27
Nessuna -
5891 M-S Uscita relè QX2(come "uscita relè QX1")
Nessuna
5892 M-S Uscita relè QX3(come "uscita relè QX1")
Nessuna
5894 M-S Uscita relè QX4(come "uscita relè QX1")
Nessuna
5930 M-S
Ingresso sonda BX1Nessuna ¦ Sonda ACS B31 ¦ Sonda collettore B6 ¦ Sonda ritorno B7 ¦ Sonda circolazione ACS B39 ¦ Sonda buffer B4 ¦ Sonda buffer B41 ¦ Sonda temp. fumi B8 ¦ Sonda mandata comune B10 ¦ Sonda caldaia a legna B22 ¦ Sonda carico ACS B36 ¦ Sonda buffer B42 ¦ Sonda ri-torno comune B73 ¦ Sonda riotrno cascata B70 ¦ Sonda piscina B13 ¦ Sonda collettore 2 B61 ¦ Sonda mandata solare B63 ¦ Sonda ritorno solare B64
Nessuna -
5931 M-S Ingresso sonda BX2(come "ingresso sonda BX1")
Nessuna
5932 M-S Ingresso sonda BX3(come "ingresso sonda BX1")
Nessuna
5933 M-S Ingresso sonda BX4(come "ingresso sonda BX1")
Nessuna
Prog N°(sul
display)
Presenzanel menu
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
CampoUnità
di misuraMin Max
- 44 -
5950 M-S
Funzione input H1Commutaz. regime CR+ACS ¦ Commutaz. regime CR ¦ Commutaz. regime CR1 ¦ Commutaz. regime CR2 ¦ Commutaz. regime CRP ¦ Blocco produzione calore ¦ Errore/messaggio allarme ¦ Setpoint minimo mandata ¦ Smaltimento calore in eccesso ¦ Consenso piscina ¦ Richiesta di calore 10V ¦ Misurazione pressione 10V
Commutazione regimeCR+ACS
5951 M-S Logica contatto H1Normalmente chiuso ¦ Normalmente aperto
Normalmente aperto -
5952 M-S Setpoint minimo mandata H1 70 8 120 °C
5954 M-S Valore temperatura 10V H1 100 5 130 °C
5956 M-S Valore pressione 3.5V H1 5.0 0.0 10.0 bar
5960 M-S
Funzione input H3Commutaz. regime CR+ACS ¦ Commutaz. regime CR ¦ Commutaz. regime CR1 ¦ Commutaz. regime CR2 ¦ Commutaz. regime CRP ¦ Blocco produzione calore ¦ Errore/messaggio allarme ¦ Setpoint minimo mandata ¦ Smaltimento calore in eccesso ¦ Consenso piscina ¦ Richiesta di calore 10V ¦ Misurazione pressione 10V
Commutazione regimeCR+ACS
-
5961 M-S Logica contatto H3Normalmente chiuso ¦ Normalmente aperto
Normalmente aperto -
5962 M-S Setpoint minimo mandata H3 70 8 120 °C
5964 M-S Valore temperatura 10V H3 100 5 130 °C
5966 M-S Valore pressione 3.5V H3 5.0 0.0 10.0 bar
5982 M-S
Funzione ingresso EX2Contatore 2° stadio bruciatore ¦ Blocco generazione produzione calore ¦ Errore/messaggio allarme ¦ Messag-gio errore SLTì ¦ Smaltimento calore in eccesso
Contatore 2° stadio bruciatore
-
5983 M-S Logica input EX2Normalmente chiuso ¦ Normalmente aperto
Normalmente aperto
6014 M-S
Funzione gruppo mix1Circuito riscaldamento 1 ¦ Contr. temp. ritorno ¦ Contr. prim/pompa sistema ¦ Contr. carico ACS ¦ ACS istanta-nea ¦ Controllo ritorno cascata
Circuito ricaldamento 1
6015 M-S
Funzione gruppo mix2Circuito riscaldamento 2 ¦ Contr. temp. ritorno ¦ Contr. prim/pompa sistema ¦ Contr. carico ACS ¦ ACS istanta-nea ¦ Controllo ritorno cascata
Circuito riscaldamento 2
6020 M-S
Funzionemodulod'estensione1Nessuno ¦ Multifunzionale ¦ Circuito riscaldamento 2 ¦ Controllo temp. ritorno ¦ Solare ACS ¦ Contr.prim/ pompa sist. ¦ Contr. carico ACS ¦ ACS istantanea ¦ Controllo ritorno cascata
Nessuno -
6021 M-S
Funzionemodulod'estensione2Nessuno ¦ Multifunzionale ¦ Circuito riscaldamento 2 ¦ Controllo temp. ritorno ¦ Solare ACS ¦ Contr.prim/ pompa sist. ¦ Contr. carico ACS ¦ ACS istantanea ¦ Controllo ritorno cascata
Nessuno -
6030 M-S
Relè QX21Nessuna ¦ Pompa di ricircolo Q4 ¦ Resistenza elettrica ACS K6 ¦ Pompa collettore Q5 ¦ Pompa H1 Q15 ¦ Pompa caldaia Q1 ¦ Pompa by-pass Q12 ¦ Uscita allarme K10 ¦ Velocità pompa CR1 Q21 ¦ Velocità pompa CR2 Q22 ¦ Velocità pompa CRP Q23 ¦ Pompa CRP Q20 ¦ Pompa H2 Q18 ¦ Pompa sistema Q14 ¦ Valvola deviatrice Y4 ¦ Pompa caldaia a legna Q10 ¦ Programma orario 5 K13 ¦ Valvola ritorno buffer Y15 ¦ Pompa scambiatore esterno solare K9 ¦ Elem. controllo solare bollitore K8 ¦ Elem. controllo solare piscina K18 ¦ Pompa collettore 2 Q16 ¦ H3 pompa Q19 ¦ Relè fumi K17 ¦ Ventil comb assistita K30 ¦ Pompa ca-scata Q25 ¦ Pompa trasf bollitore Q11 ¦ Pompa mix ACS Q35 ¦ Pompa interm. ACS Q33 ¦ Richiesta calore K27
Nessuna
6031 M-S OutputrelèQX22(come "Relè QX21")
Nessuna
Prog N°(sul
display)
Presenzanel
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
CampoUnità
di misuraMin Max
- 45 -
IT
6032 M-S M-S OutputrelèQX23(come "Relè QX21")
nessuna
6040 M-S
Sonda input BX21Nessuna ¦ Sonda ACS B31 ¦ Sonda collettore B6 ¦ Sonda ritorno B7 ¦ Sonda circolazione ACS B39 ¦ Sonda buffer B4 ¦ Sonda buffer B41 ¦ Sonda temp. fumi B8 ¦ Sonda mandata comune B10 ¦ Sonda caldaia a legna B22 ¦ Sonda carico ACS B36 ¦ Sonda buffer B42 ¦ Sonda ri-torno comune B73 ¦ Sonda riotrno cascata B70 ¦ Sonda piscina B13 ¦ Sonda collettore 2 B61 ¦ Sonda mandata solare B63 ¦ Sonda ritorno solare B64
nessuna
6041 M-S Sonda input BX22(come "sonda input BX21")
nessuna
6046 M-S
Funzione input H2Commutaz. regime CR+ACS ¦ Commutaz. regime CR ¦ Commutaz. regime CR1 ¦ Commutaz. regime CR2 ¦ Commutaz. regime CRP ¦ Blocco produzione calore ¦ Errore/messaggio allarme ¦ Setpoint minimo mandata ¦ Smaltimento calore in eccesso ¦ Consenso piscina ¦ Richiesta di calore 10V ¦ Misurazione pressione 10V
Commutazione regimeCR+ACS
6047 M-S Logica contatto H2Normalmente chiuso ¦ Normalmente aperto
Normalmente aperto
6048 M-S Setpoint minimo mandata H2 70 8 120 °C
6050 M-S Valore temperatura 10V H2 100 5 130 °C
6052 M-S Valore pressione 3.5V H2 5.0 0.0 10.0 bar
6070 M-S
Funzione output UXNessuna ¦ Pompa caldaia Q1 ¦ Pompa ACS Q3 ¦ Pompa interm. ACS Q33 ¦ Pompa circ.risc. 1 Q2 ¦ Pompa CR2 Q6 ¦ Pompa CRP Q20 ¦ Pompa collettore Q5 ¦ Pompa scamb. est. solare K9 ¦ Pompa sol. bollitore K8 ¦ Pompa sol. piscina K18 ¦ Pompa collettore 2 Q16 ¦ Setpoint caldaia ¦ Setpoint output ¦ Richiesta calore
Nessuna
6071 M-S Logica output UXstandard ¦ invertito
Standard
6075 M-S Valore temperatura 10V UX 100 5 130 °C
6097 S Tipo sonda temp collettoreNTC ¦ Platinum 100
NTC -
6098 S Correzione sonda collettore 0 -20 20 °C
6099 S Correzione sensore 2 collettore 0 -20 20 °C
6100 S Correzione sonda esterna 0.0 -3.0 3.0 °C
6101 S Tipo sonda temperatura fumiNTC ¦ PT 100
NTC -
6102 S Correzione sonda temperatura fumi 0 -20 20 °C
6110 S Costante di tempo edificio 15 0 50 h
6120 S Protezione antigelo impiantoOff ¦ On
Off -
6128 S Richiesta calore sotto temperatura estiva -- ---/-50 50 °C
6129 S Richiesta calore sopra temperatura estiva -- ---/-50 50 °C
6131 S Richiesta di calore in modalità ecoOff ¦ ACS On ¦ On
Off
6200 M-S Memorizzazione sondaNo ¦ Si
No -
6205 S Ripristinare parametri (di fabbrica/default)No ¦ Si
No -
6212 M-S Check N. generatore 1 - 0 199999 -
6213 M-S Check N. generatore 2 - 0 199999 -
6215 M-S Check N. bollitore - 0 199999 -
Prog N°(sul
display)
Presenzanel menu
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
CampoUnità
di misuraMin Max
- 46 -
6217 M-S Check N. circuiti riscaldamento - 0 199999 -
6220 S Versione software - 0 99.9 -
LPB6600 M-S Indirizzo apparecchio 1 0 16 -
6601 S Indirizzo segmento 0 0 14 -
6604 S Funzione alimentazione del BusOff ¦ Automatico
Automatico -
6605 S Stato alimentazione del BusOff ¦ On
On -
6620 S Azione commutazioniSegmento ¦ Sistema
Sistema -
6621 S Commutazione estateLocalmente ¦ Centrale
Localmente -
6623 S Commutazione regimeLocalmente ¦ Centrale
Centrale
6624 S Blocco generatore manualeLocalmente ¦ Centrale
Localmente
6625 SAssegnazione sanitarioTutti i cir. riscald. locali ¦ Tutti i cir. riscald. nel segmento ¦ Tutti i cir. riscald. nel sistema
Tutti i circuiti di riscaldamento nel sistema
-
6631 S Sorgente est. in modalità EcoOff ¦ ACS ON ¦ On
Off
6640 M-S Modo orologioAutonomo ¦ Slave senza imp. remota ¦ Slave con imp. remota ¦ Master
Autonomo -
6650 S Acquisizione temperatura esterna 0 0 239 -
Guasto
6710 M-S Reset relè di allarmeNo ¦ Si
No
6740 S Allarme temp. mandata 1 --- ---/10 240 min
6741 S Allarme temp. mandata 2 --- ---/10 240 min
6743 S Allarme temp. caldaia --- ---/10 240 min
6745 S Allarme carico ACS ---- ---/10 48 h
6800 S Cronologia 1Codice errore 1
- 0 255 -
6802 S Cronologia 2Codice errore 2
- 0 255 -
6804 S Cronologia 3Codice errore 3
- 0 255 -
6806 S Cronologia 4Codice errore 4
- 0 255 -
6808 S Cronologia 5Codice errore 5
- 0 255255 -
6810 S Cronologia 6Codice errore 6
- 0 255 -
6812 S Cronologia 7Codice errore 7
- 0 255 -
6814 S Cronologia 8Codice errore 8
- 0 255 -
6816 S Cronologia 9Codice errore 9
- 0 255 -
6818 S Cronologia 10Codice errore 10
- 0 255 -
Funzione Manutenzione/Service7040 S Intervallo ore funzionamento bruciatore --- ---/10 10000 h
7041 S Orefunzionamentobruciatoredopomanutenzione 0 0 10000 h
7042 S Intervallo avviamenti bruciatore --- ---/60 65535 -
7043 S Avviamenti bruciatore dopo manutenzione 0 0 65535 -
7044 S Intervallo di manutenzione --- ---/1 240 mesi
7045 S Tempo trascorso dopo manutenzione 0 0 240 mesi
Prog N°(sul
display)
Presenzanel menu
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
CampoUnità
di misuraMin Max
- 47 -
IT7053 S Limite temperatura fumi --- ---/0 350 °C
7054 S Ritardo allarme temperatura fumi 0 0 120 min
7119 S FunzioneECOBloccato ¦ Abilitato
Bloccato
7120 T ModalitàECOOff ¦ On
Off
7130 T Funzione spazzacaminoOff ¦ On
Off -
7140 T Funzionamento manualeOff ¦ On
Off -
7150 M-S Simulazione temperatura esterna - -50.0 50 °C
7170 M-S Telefono servizio clienti - -
Test input/output
7700 M-S
Test relèNessun test ¦ Tutto off ¦ 1° stadio bruciatore T2 ¦ stadio 1-2 bruc. T2/QX4 ¦ Pompa ACS Q3 ¦ Pompa CR Q2 ¦ Miscelatore CR aperto Y1 ¦ Miscelatore CR chiuso Y2 ¦ Pompa CR Q6 ¦ Miscelatore CR aperto Y5 ¦ Miscelatore CR chiuso Y6 ¦ Uscita relè QX1 ¦ Uscita relè QX2 ¦ Uscita relè QX 3 ¦ Uscita relè QX4 ¦ Uscita relè QX21 modulo 1 ¦ Uscita relè QX22 modulo 1 ¦ Uscita relè QX23 modulo 1 ¦ Uscita relè QX21 modulo 2 ¦ Uscita relè QX22 modulo 2 ¦ Uscita relè QX23 modulo 2
Nessun test -
7710 M-S Test uscita UX - 0 100 5
7711 M-S Valvole tensione UX 0 0 10 Volt
7730 M-S Temperatura esterna B9 - -50.0 50 °C
7732 M-S Temperatura di mandata B1 - 0.0 140 °C
7734 M-S Temperatura di mandata B12 - 0.0 140 °C
7750 M-S Temperatura ACS B3 - 0.0 140 °C
7760 M-S Temperatura di caldaia B2 - 0.0 140 °C
7820 M-S Sonda temperatura BX1 - -28.00 350 °C
7821 M-S Sonda temperatura BX2 - -28.00 350 °C
7822 M-S Sonda temperatura BX3 0 -28 350 °C
7823 M-S Sonda temperatura BX4 0 -28 350 °C
7830 M-S Sonda temperatura BX21 modulo 1 0 -28 350 °C
7831 M-S Sonda temperatura BX22 modulo 1 0 -28 3,50 °C
7832 M-S Sonda temperatura BX21 modulo 2 0 -28 350 °C
7833 M-S Sonda temperatura BX22 modulo 2 0 -28 350 °C
7840 M-S Segnale di tensione H1 - 0 10 Volt
7841 M-S Stato del contatto H1Aperto ¦ Chiuso
Aperto -
7845 M-S Segnale di tensione H2 0 0 10 °C
7846 M-S Stato del contatto H2Aperto ¦ Chiuso
Aperto -
7854 M-S Segnale di tensione H3 0 0 10 Volt
7855 M-S Stato del contatto H3Aperto ¦ Chiuso
Aperto
7870 M-S Guasto bruciatore S30V ¦ 230V
0 V -
7881 M-S 1° stadio bruciatore E10V ¦ 230V
0 V -
7912 M-S Imput_ EX20V ¦ 230V
0 V -
Stato8000 M-S Stato circuito riscaldamento 1 - -
8001 M-S Stato circuito riscaldamento 2 - -
8002 M-S Stato circuito riscaldamento P - -
Prog N°(sul
display)
Presenzanel menu
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
CampoUnità
di misuraMin Max
- 48 -
8003 M-S Stato ACS - -
8005 M-S Stato Caldaia - -
8007 M-S Stato solare - -
8008 M-S Stato caldaia a legna - -
8010 M-S Stato buffer - -
8011 M-S Stato piscina - -
Diagnostica generazione di calore8100 fino a 8013
M-S Priorità di generazione 1...16
8101 fino a 8131
M-S
Stato generatore 1...16Manca ¦ In riscaldamento ¦ azionamento manuale attivo ¦ Blocco produttore attivi ¦ Effetto spazzacamino attivo ¦ Commutazione attiva ACS ¦ Limitazione temperatura esterna attiva ¦ Nessuna attivazione ¦ Attivo
8138 M-S Temperatura di mandata generatore in cascata 0 0 140 °C
8139 M-S Setpoint di mandata generatore in cascata 0 0 140 °C
8140 M-S Temperatura di ritorno generatore in cascata 0 0 140 °C
8141 M-S Setpoint di ritorno generatore in cascata 0 0 140 °C
8150 M-S Commutazione attuale produttore 0 0 990 h
Parametri diagnostica
8300 M-S 1° stadio bruciatore T2Off ¦ On
On -
8301 M-S 2° stadio bruciatoreOff ¦ On
On -
8308 S Velocità pompa caldaia 0 0 100 %
8310 M-S Temperatura caldaiaSetpoint caldaia
- 0.0 140.0 °C
8312 T Punto commutazione caldaia 0 0 140 °C
8314 T Temperatura ritorno caldaia - 0.0 140.0 °C
8316 M-S Temperatura fumi 0 0 350 °C
8318 M-S Max temperatura fumi 0 0 350 °C
8326 M-S Modulazione bruciatori 0 0 100 %
8330 S Oredifunzione1°stadio 0 0 65535 h
8331 S N. avviamenti 1° stadio - 0 199999 -
8332 S Oredifunzione2°stadio 0 0 65535 h
8333 S N. avviamenti 2 stadio 0 0 199999 -
8505 S Velocità pompa di collet. 1 0 0 100 %
8506 S Velocità pompa solare scambio esterno 0 0 100 %
8507 S Velocità pompa solare buffer 0 0 100 %
8508 S Velocità pompa solare piscina 0 0 100 %
8510 M-S Temperatura collettore 1 - -28.0 350 °C
8511 M-S Temperatura collettore 1 max 0 -28.0 350 °C
8512 M-S Temperatura collettore 1 min 0 -28.0 350 °C
8513 M-S ∆T collettore 1/ACS - -168.0 350 °C
8514 M-S ∆T collettore 1/bollitore - -168.0 350 °C
8515 M-S ∆T collettore 1/piscina - -168.0 350 °C
8519 M-S Temperatura mandata solare 0 -28.0 350 °C
8520 M-S Temperatura ritorno solare 0 -28.0 350 °C
8526 T Energia solare ceduta 24-ore 0 0 999.9 kW
8527 T Totale energia solare ceduta 0 0 9999999.9
8530 M-S Oredifunzioneproduzionesoalre - 0 65535
Prog N°(sul
display)
Presenzanel menu
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
CampoUnità
di misuraMin Max
- 49 -
IT8531 S Oredifunzionesurriscaldamentocollettore - 0 65535 h
8543 S Velocità pompa collettore 2 0 0 100 %
8547 M-S Temperatura collettore 2 0 -28.0 350 °C
8548 M-S Temperatura collettore 2 max -28.0 -28.0 350 °C
8549 M-S Temperatura collettore 2 min 3500 -28 350 °C
8550 M-S ∆T collettore 2/ACS 0 -168 350 °C
8551 M-S ∆T collettore 2/buffer 0 -168 350 °C
8552 M-S ∆T collettore 2/piscina 0 -168 350 °C
8560 M-S Temperatura caldaia a legna 0 0 140 °C
8570 M-S Orefunzionecaldaiaalegna 0 0 65535 h
Test input/output8700 M-S Temperatura esterna - -50.0 50.0 °C
8703 M-S Temperatura esterna attenuata - -50.0 50.0 °C
8704 M-S Temperatura esterna composta - -50.0 50.0 °C
8730 M-S Pompa CR QROff ¦ On
Off -
8731 M-S ValvolamiscelatriceCRapertoY1Off ¦ On
Off -
8732 M-S ValvolamiscelatriceCRchiusoY2Off ¦ On
Off -
8735 S Velocità pompa CR1 0 0 100 %
8740 M-S Temperatura ambiente 1 --
4.050
35.0°C
8743 M-S Temperatura di mandata 1 - 0.0 140.0 °C
8760 M-S Pompa CR2Off ¦ On
Off -
8761 M-S Valvola mix 2 CR apertaOff ¦ On
Off -
8762 M-S Valvola mix 2 CR chiusaOff ¦ On
Off -
8765 M-S Velocità pompa CR2 0 0 100 %
8770 M-S Temperatura ambiente 2 --
4.050
35.0°C
8773 M-S Temperatura di mandata 2 - 0.0 140.0 °C
8795 M-S Velocità pompa CR P 0 0 100 %
8800 M-S Temperatura ambiente P --
4.050
35.0°C
8803 M-S Setpoint mandata P - 0.0 140.0 °C
8820 M-S Pompa ACS Q3Off ¦ On
Off -
8825 S Velocità pompa ACS 0 0 100 %
8826 S Velocità pompa circol. intermedio ACS 0 0 100 %
8830 M-S Temperatura ACS 1 -0.08.0
140.080.0
°C
8832 M-S Temperatura ACS 2 - 0.0 140.0 °C
8835 M-S Temperatura circolazione sanitario - 0.0 140.0 °C
8836 M-S Temperatura carico ACS 0 0 140 °C
8850 M-S Controllo primario temperatura ACSSetpoint controllo primario
0 0 140 °C
8852 M-S Temp. consumo ACS setpoint riscaldamento ACS 0 0 140 °C
8900 M-S Temperatura piscina0
2408
14080
°C
8930 M-S Temp. regolazione primaria - 0.0 140.0 °C
Prog N°(sul
display)
Presenzanel menu
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
CampoUnità
di misuraMin Max
- 50 -
8950 M-S Temperatura di mandata comuneSetpoint di mandata comune
- 0.0 140-0 °C
8952 M-S Temperatura comune di ritorno 0 0 140 °C
8962 M-S Setpoint output comune 0 0 100 °C
8980 M-S Temperatura buffer 1 - 0.0 140-0 °C
8981 M-S Setpoint buffer 0 0 140 °C
8982 M-S Temperatura buffer 2 - 0.0 140.0 °C
8983 M-S Temperatura buffer 3 0 0 140 °C
9000 M-S Setpoint mandata H1 - 5.0 130.0 °C
9001 M-S Setpoint mandata H2 - 5.0 130.0 °C
9004 M-S Setpoint mandata H3 8 8 120 °C
9005 M-S Pressione acqua H1 - 0.0 10.0 bar
9006 M-S Pressione acqua H2 - 0.0 10.0 bar
9009 M-S Pressione acqua H3 - 0 10.0 bar
9031 Uscita relè QX1Off ¦ On
Off -
9032 Uscita relè QX2Off ¦ On
Off -
9033 M-S Uscita relè QX3Off ¦ On
Off -
9034 M-S Uscita relè QX4Off ¦ On
Off -
9050 M-S Uscita relè QX21 modulo 1Off ¦ On
Off -
9051 M-S Uscita relè QX22 modulo 1Off ¦ On
Off -
9052 M-S Uscita relè QX23 modulo 1Off ¦ On
Off -
9053 M-S Uscita relè QX21 modulo 2Off ¦ On
Off -
9054 M-S Uscita relè QX22 modulo 2Off ¦ On
Off -
9055 M-S Uscita relè QX23 modulo 2Off ¦ On
Off -
Prog N°(sul
display)
Presenzanel menu
FunzioneLinea/parametro del sottomenu
Impostazionedi fabbrica(default)
CampoUnità
di misuraMin Max
- 51 -
ITIl simbolo “campana” sul display indica che si è verificato un errore/guasto e per visualizzarne la causa si deve premere il tasto
31. CODICI DI ERRORE/GUASTO
Codice Errore Descrizione0 Nessun errore
10 Sonda temperatura esterna
20 Sonda temperatura caldaia 1
25 Sonda temperatura caldaia a combustibile solido
26 Sonda temperatura flusso comune
28 Sonda di temperatura fumi
30 Sonda temperature flusso 1
32 Sonda mandata 2
38 Controllo primario temperature di mandata
40 Sonda temperature di ritorno 1
46 Sonda temperatura di ritorno cascata
47 Sonda temperatura comune
50 Sonda acqua sanitaria 1
52 Sonda acqua sanitaria 2
54 Sonda regolatore primario ACS
57 Sonda temperatura di circolazione ACS
70 Sonda cisterna di deposito Buffer 1
71 Sonda cisterna di deposito Buffer 2
72 Sonda cisterna di deposito Buffer 3
73 Sonda collettore 1
74 Sonda collettore 2
81 LPB corto-circuito/comm
82 LPB collisione indirizzo
83 BSB corto-circuito
84 BSB collisione indirizzo
100 Orarioprincipale(LPB)
102 Orologioprincipalesenzariserva(LPB)
105 Messaggio di manutenzione
109 Supervisione temperature caldaia
110 Blocco di TSC
117 Pressione acqua troppo alta
118 Pressione acqua troppo bassa (limite critico)
121 Supervisione Temperatura di mandata 1 (HC1)
122 Supervisione Temperatura di mandata 2 (HC2)
126 Controllo carico acqua sanitaria
127 Temperatura funzione legionella non raggiunto
131 Guasto bruciatore
146 Configurazione messaggio di errore comune
171 Contatto allarme 1 attivo
172 Contatto allarme 2 attivo
173 Contatto allarme 3 attivo (EX2/230VAC)
174 Contatto allarme 4 attivo (H3)
176 Pressione acqua 2 troppo alta
177 Pressione acqua 2 troppo bassa (limite critico)
178 Controllo di temperatura circuito riscaldamento 1
179 Controllo di temperatura circuito riscaldamento 2
217 Messaggio errore comune
218 Messaggio errore supervisione pressione
241 Sonda di mandata, errore sonda solare
242 Sonda di ritorno, errore sonda solare
243 Sonda di temperatura piscina
31.1 LEGENDA CODICI
- 52 -
Codice Errore Descrizione320 Sonda temperatura di carico ACS
321 Errore istantaneo della sonda di temperatura del riscaldatore di ACS
322 Pressione acqua 3 troppo alta
323 Pressione acqua 3 troppo bassa
324 BX stesse sonde
326 BX/stessa sonda gruppo valvola miscelazione
328 Stessa funzione gruppo valvola miscelazione
329 Modulo di espansione / stessa funzione gruppo valvola miscelazione
330 BX1 nessuna funzione
331 BX2 nessuna funzione
332 BX3 nessuna funzione
333 BX4 nessuna funzione
339 Manca la pompa di collettore Q5
340 Manca la pompa di collettore Q16
341 Manca la sonda di collettore B6
342 Manca la sonda B31 Solare ACS
343 Manca il collegamento solare
344 Manca controllo solare Buffer K8
345 Manca elemento controllo solare piscina K18
346 Manca pompa caldaia a legna Q10
347 Manca sonda di comparazione caldaia a legna
348 Errore di indirizzo caldaia a legna
349 MancavalvoladiritornoBufferY15
350 Errore indirizzo deposito Buffer
351 Errore indirizzo controllo primario/pompa di sistema
353 Manca sonda di cascata B10
366 Errore sonda temperatura ambiente Hx
Cod. Manutenzione Descrizione1 Oredifunzionamentobruciatoreineccesso
2 Avviamenti bruciatore in eccesso
3 Intervallo di manutenzione in eccesso
5 Pressione dell’acqua circuito di riscaldamento troppo bassa (pressione scesa sotto il limite inferiore 1)
18 Pressione dell’acqua circuito di riscaldamento troppo bassa (pressione scesa sotto il limite inferiore 2)
21 Temperatura massima gas di combustione eccessiva
22 Pressione dell’acqua circuito di riscaldamento troppo bassa (pressione scesa sotto il limite inferiore 3)
Cod. Funzione Descrizione301 Funzionamento manuale
302 Test TSC
303 Funzione spazzacamino
309 Simulazione temperature esterna
310 Funzionamento energia alternativa
314 Modalità Economy
31.2 CODICI DI MANUTENZIONE
31.3 CODICI DI FUNZIONI SPECIALI
- 53 -
32. ESEMPI DI SCHEMI REALIZZABILI (DIAGRAMMI PARZIALI E FUNZIONI AUSILIARIE)
32.1 LEGENDA SCHEMI
Abbreviazioni generali
BX Ingresso multifunzionale/sondaHX (H1 e H3) Ingresso multifunzionale a bassa tensione (0-10V)MG Gruppo di miscelazioneQX Uscita multifunzionale/relèUX Ingresso multifunzionale a bassa tensione (0-10V) LP Linea/parametro
Legenda Alta tensione
K6 Riscaldatore elettrico ad immersione ACSK4 1° stadio bruciatoreK5 2° stadio bruciatoreK8 Elemento di controllo del serbatoio di riserva (buffer)K9 Pompa scambiatore di calore esternoK16 Riscaldatore elettrico ad immersione serbatoio di riserva (buffer) o serbatoio di riserva combinatoK17 Relè gas di scaricoK18 Elemento di controllo solare per la piscinaK30 Ventilatore accensione assistitaQ1 Pompa della caldaiaQ2 Pompa circuito riscaldamento CR1Q3 Pompa ACSQ4 Pompa circolazione impianto sanitario ACSQ5 Pompa collettore solareQ6 Pompa circuito riscaldamento CR2Q10 Pompa caldaia combustibile solidoQ11 Pompa di ricarica del serbatoio di riserva (buffer)Q12 Pompa bypassQ15 Pompa H1Q16 Pompa 2° collettore solareQ19 Pompa H3Q25 Pompa della cascataQ33 Pompa del circuito di riscaldamento intermedioQ34 Pompa del riscaldatore istantaneo ACSY4 ValvolageneraledichiusuradellafontedicaloreY7/Y8 Valvolamiscelatricemantenimentotemperaturadiritornoincaldaia(APRE/CHIUDE)Y15 ValvoladiritornodelserbatoiodiriservaY17/Y18 Modulazionebruciatore(APRE/CHIUDE)Y25/Y26 Valvolamiscelatricemantenimentotemperaturadiritornocascata(APRE/CHIUDE)Y31/Y32 ValvolamiscelatricedicontrolloprimarioACS(APRE/CHIUDE)Y33/Y34 Valvoladelriscaldatoreistantaneodell’impiantosanitarioACS(APRE/CHIUDE)
Legenda Bassa tensione
B2 Sonda mandata caldaia B3 Sonda bollitore ACS (in alto)B4 Sonda serbatoio di riserva buffer (in alto)B6 Sonda collettore solareB7 Sonda ritorno caldaiaB8 Sonda temperatura fumiB10 Sonda mandata comune (cascata)B13 Sonda temperatura piscinaB22 Sonda caldaia combustibile solido (mandata)B31 Sonda bollitore ACS (in basso)B36 Sonda di carico ACSB38 Sonda uscita riscaldatore istantaneo ACSB39 Sonda circolazione impianto sanitario ACSB41 Sonda serbatoio di riserva buffer (in basso)B42 Sonda serbatoio di riserva buffer (posizione intermedia)B61 Sonda secondo collettore solareB63 Sonda mandata solare (alta temperatura)B64 Sonda ritorno solare (bassa temperatura)B70 Sonda ritorno cascataB73 Sonda di ritorno comune del circuito primarioFS Flussostato
- 54 -
IMPOSTAZIONI NECESSARIE:QX:- Pompa caldaia Q1 LP5770 (Tipo sorgente): - 1-stadio, o - Senza sonda caldaia
IMPOSTAZIONI OPZIONALI:BX:- Sonda ritorno B7
IMPOSTAZIONI NECESSARIE:QX:- Pompa ricircolo (bypass) Q12 LP5770 (Tipo sorgente): - 1-stadio, o - Senza sonda caldaia
IMPOSTAZIONI OPZIONALI:BX:- Sonda ritorno B7
IMPOSTAZIONI NECESSARIE:QX:- Pompa caldaia Q1- Pompa ricircolo (bypass) Q12 LP5770 (Tipo sorgente): - 1-stadio, o - Senza sonda caldaia
IMPOSTAZIONI OPZIONALI:BX:- Sonda ritorno B7
IMPOSTAZIONI NECESSARIE:LP5770 (Tipo sorgente): - 1-stadio, o - Senza sonda caldaia
IMPOSTAZIONI OPZIONALI:BX:- Sonda ritorno B7
B2
B7
K4
K4
K4
K5
OeG1
OeG2
OeG3
B2
B2
B2
Q1
B7
B7
B7
K4/K5
T
T
T
T
T
T
T
T
IMPOSTAZIONI NECESSARIE:LP5770 (Tipo sorgente): - 2-stadi, o- 2 x 1 cascata
IMPOSTAZIONI OPZIONALI:BX:- Sonda ritorno B7
B2
B7
K4
K4
K4
K5
OeG1
OeG2
OeG3
B2
B2
B2
Q1
B7
B7
B7
K4/K5
T
T
T
T
T
T
T
T
B2
B7
K4
K4
K4
K5
OeG1
OeG2
OeG3
B2
B2
B2
Q1
B7
B7
B7
K4/K5
T
T
T
T
T
T
T
T
OeG4
OeG5
OeG6
B2
B2
B2
B2
B2
B7
B7
B7
B7
B7
K4/K5
K4/K5
Q1
Q2
K5 K4
K5 K4
K4
Q1
Q12
Q12
Q12
T
T
T
T
T
T
T
T
T
T
OeG7
OeG8
OeG9
B7
K4
Q1 Q12
B2 T
T
B2 T
B2 T
B7 T
B7T
B7T
B2T
K4/K5
K4
K4K5
Q1 Q12
Q1Q1Q12
Q1
Y7/Y8
OeG4
OeG5
OeG6
B2
B2
B2
B2
B2
B7
B7
B7
B7
B7
K4/K5
K4/K5
Q1
Q2
K5 K4
K5 K4
K4
Q1
Q12
Q12
Q12
T
T
T
T
T
T
T
T
T
T
OeG4
OeG5
OeG6
B2
B2
B2
B2
B2
B7
B7
B7
B7
B7
K4/K5
K4/K5
Q1
Q2
K5 K4
K5 K4
K4
Q1
Q12
Q12
Q12
T
T
T
T
T
T
T
T
T
T
IMPOSTAZIONI NECESSARIE:QX:- Pompa caldaia Q1 LP5770 (Tipo sorgente): - 2-stadi, o- 2 x 1cascata
IMPOSTAZIONI OPZIONALI:BX:- Sonda ritorno B7
Nota: Per cascata di 2 generatori collegare Pompa Q1 ai morsetti QX1, QX2.
IMPOSTAZIONI NECESSARIE:QX:- Pompa ricircolo (bypass) Q12 LP5770 (Tipo sorgente): - 2-stadi, o- 2 x 1 cascata
IMPOSTAZIONI OPZIONALI:BX:- Sonda ritorno B7
GENERATORE DI CALORE
Multistadio gasolio/gas
GENERATORE DI CALORE
Multistadio gasolio/gas
32.2 SCHEMI
- 55 -
IT
OeG7
OeG8
OeG9
B7
K4
Q1 Q12
B2 T
T
B2 T
B2 T
B7 T
B7T
B7T
B2T
K4/K5
K4
K4K5
Q1 Q12
Q1Q1Q12
Q1
Y7/Y8
OeG11
OeG12
OeG13
OeG14
OeG15
B2 T
B2 T
B7T
B7T
B7T
B7T
B7 T
UXY17/Y18
UXY17/Y18
UXY17/Y18
UXY17/Y18
UXY17/Y18
Q1
Q1 Q12
Q12
Q1
Y7/Y8
K4
B2 T
B2 T
B2 T
K4
K4
K4
K4
OeG11
OeG12
OeG13
OeG14
OeG15
B2 T
B2 T
B7T
B7T
B7T
B7T
B7 T
UXY17/Y18
UXY17/Y18
UXY17/Y18
UXY17/Y18
UXY17/Y18
Q1
Q1 Q12
Q12
Q1
Y7/Y8
K4
B2 T
B2 T
B2 T
K4
K4
K4
K4
OeG11
OeG12
OeG13
OeG14
OeG15
B2 T
B2 T
B7T
B7T
B7T
B7T
B7 T
UXY17/Y18
UXY17/Y18
UXY17/Y18
UXY17/Y18
UXY17/Y18
Q1
Q1 Q12
Q12
Q1
Y7/Y8
K4
B2 T
B2 T
B2 T
K4
K4
K4
K4
OeG11
OeG12
OeG13
OeG14
OeG15
B2 T
B2 T
B7T
B7T
B7T
B7T
B7 T
UXY17/Y18
UXY17/Y18
UXY17/Y18
UXY17/Y18
UXY17/Y18
Q1
Q1 Q12
Q12
Q1
Y7/Y8
K4
B2 T
B2 T
B2 T
K4
K4
K4
K4
OeG11
OeG12
OeG13
OeG14
OeG15
B2 T
B2 T
B7T
B7T
B7T
B7T
B7 T
UXY17/Y18
UXY17/Y18
UXY17/Y18
UXY17/Y18
UXY17/Y18
Q1
Q1 Q12
Q12
Q1
Y7/Y8
K4
B2 T
B2 T
B2 T
K4
K4
K4
K4
OeG7
OeG8
OeG9
B7
K4
Q1 Q12
B2 T
T
B2 T
B2 T
B7 T
B7T
B7T
B2T
K4/K5
K4
K4K5
Q1 Q12
Q1Q1Q12
Q1
Y7/Y8
OeG10
B2 T
B7T
B2T
B7 T
Q1
Y7/Y8
K4/K5
K4K5
Q1Q1
Y7/Y8
IMPOSTAZIONI NECESSARIE:MG (LP 6014, 6015):- Mantenimento temperatura ritornoLP5770 (Tipo sorgente): - 1-stadio, o - Senza sonda caldaia
IMPOSTAZIONI NECESSARIE:QX:- Pompa caldaia Q1- Pompa ricircolo (bypass) Q12 LP5770 (Tipo sorgente): - 2-stadi, o- 2 x 1 cascata
IMPOSTAZIONI OPZIONALI:BX:- Sonda ritorno B7
Nota: Per cascata di 2 generatori collegare Pompe Q1 ai morsetti QX1, QX2.
IMPOSTAZIONI NECESSARIE:LP5770 (Tipo sorgente): - Modulante 3-posizioni, o- Modulante UX
IMPOSTAZIONI OPZIONALI:BX:- Sonda ritorno B7
IMPOSTAZIONI NECESSARIE:QX:- Pompa caldaia Q1LP5770 (Tipo sorgente): - Modulante 3-posizioni, o- Modulante UX
IMPOSTAZIONI OPZIONALI:BX:- Sonda ritorno B7
IMPOSTAZIONI NECESSARIE:QX:- Pompa ricircolo (bypass) Q12LP5770 (Tipo sorgente): - Modulante 3-posizioni, o- Modulante UX
IMPOSTAZIONI OPZIONALI:BX:- Sonda ritorno B7
IMPOSTAZIONI NECESSARIE:QX:- Pompa caldaia Q1 - Pompa ricircolo (bypass) Q12 LP5770 (Tipo sorgente): - Modulante 3-posizioni, o- Modulante UX
IMPOSTAZIONI OPZIONALI:BX:- Sonda ritorno B7
IMPOSTAZIONI NECESSARIE:MG (LP 6014, 6015):- Mantenimento temperatura ritornoLP5770 (Tipo sorgente): - Modulante 3-posizioni, o- Modulante UX
IMPOSTAZIONI NECESSARIE:MG (LP 6014, 6015):- Mantenimento temperatura ritorno LP5770 (Tipo sorgente): - 2-stadi, o- 2 x 1 cascata
Nota: Per 2x1 cascata, configura-re Pompa caldaia Q1 su QX1, QX2.
GENERATORE DI CALORE
Multistadio gasolio/gas
GENERATORE DI CALORE
Modulante gasolio/gas
- 56 -
GENERATORE DI CALORE
Combustibile solido: (wood)
SOLARE TERMICO
Impianto ad un collettore
IMPOSTAZIONI NECESSARIE:QX: - Pompa caldaia a combustibile solido Q10 BX: - Sonda caldaia a combustibile solido B22 LP4133 (Controllo ∆T M/R): - Setpoint temperatura mandata, o- Setpoint minimo
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5 BX: - Sonda collettore solare B6
IMPOSTAZIONI OPZIONALI:UX:- Q5
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Pompa scambio anello secondario K9 BX: - Sonda collettore solare B6
IMPOSTAZIONI OPZIONALI:UX:- Q5 / K9
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Componente di controllo solare: buffer K8 BX: - Sonda collettore solare B6LP5840 (Componenti di controllo solare):- Pompa di carico
IMPOSTAZIONI OPZIONALI:UX:- Q5 / K8
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Componente di controllo solare: buffer K8 BX: - Sonda collettore solare B6LP5840 (Componenti di controllo solare):- Valvola deviatrice
IMPOSTAZIONI OPZIONALI:UX:- Q5
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Componente di controllo solare: buffer K8 - Pompa anello scambio sec. K9BX: - Sonda collettore solare B6LP5840 (Comp. di controllo solare):- Pompa di carico OL5841 (Scambio solare esterno):- Insieme
IMPOSTAZIONI OPZIONALI:UX:- Q5 / K8 / K9
IMPOSTAZIONI NECESSARIE:QX: - Pompa caldaia a combustibile solido Q10 BX: - Sonda caldaia a combustibile solido B2 LP4133 (Controllo ∆T M/R): - Sonda sanitario B3, o- Sonda sanitario B31, o- Sonda accumulo (buffer) B4, o- Sonda accumulo (buffer) B41
IMPOSTAZIONI NECESSARIE:BX: - Sonda fumi B8
IMPOSTAZIONI OPZIONALI:QX:- Relè fumi K17- Ventilatore sicurezza K30
B22 T
B22 T
T
Q10
Q10
B8
T
Q5
B6 T
B6 T
B6T
Q5
K9
Q5
K8
T
T
Q5
B6 T
B6 T
B6T
Q5
K9
Q5
K8
T
T
Q5
B6 T
B6 T
B6T
Q5
K9
Q5
K8
T
T
0
1
T
T
T
T
B6T
B6T
Q5
Q5
K8
K9
K8
0
1
T
T
T
T
B6T
B6T
Q5
Q5
K8
K9
K8
B22 T
B22 T
T
Q10
Q10
B8
T
B22 T
B22 T
T
Q10
Q10
B8
T
FUNZIONI EXTRA GENERATORE DI CALORE GASOLIO/GAS E COMBUSTIBILE SOLIDO
- 57 -
IT
0
1
T
T
T
T
B6T
B6T
Q5
Q5 K9
K8
K9
K8
0
1
T
T
T
T
B6T
B6T
Q5
Q5 K9
K8
K9
K8
0
1
T
B6T
B6T
Q5
Q5
K8 K9
K9
K8
T
T
T
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Componente di cont. solare: buffer K8 - Pompa anello scambio sec. K9BX: - Sonda collettore solare B6LP5840 (Comp. di controllo solare):- Valvola deviatrice LP5841 (Scambio solare esterno):- Insieme
IMPOSTAZIONI OPZIONALI:UX: Q5 / K9
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Componente di cont. solare: buffer K8 - Pompa anello scambio sec. K9BX: - Sonda collettore solare B6LP5840 (Comp. di controllo solare):- Circolatore di carico LP5841 (Scambio solare esterno):- Accumulo sanitario
IMPOSTAZIONI OPZIONALI:UX: Q5 / K8 / K9
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Componente di cont. solare: buffer K8 - Pompa anello scambio sec. K9BX: - Sonda collettore solare B6LP5840 (Comp. di controllo solare):- Valvola deviatrice LP5841 (Scambio solare esterno):- Accumulo sanitario
IMPOSTAZIONI OPZIONALI:UX: Q5 / K9
0
1
T
B6T
B6T
Q5
Q5
K8 K9
K9
K8
T
T
T
0
1
0
1
B6T
B6T
B6T
Q5
K8
K9
K18
Q5
Q5
K18
T
T
T
T
T
T
0
1
0
1
B6T
B6T
B6T
Q5
K8
K9
K18
Q5
Q5
K18
T
T
T
T
T
T
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Componente di cont. solare: buffer K8 - Pompa anello scambio sec. K9BX: - Sonda collettore solare B6LP5840 (Comp. di controllo solare):- Pompa di caricoLP5841 (Scambio solare esterno):- Sonda accumulo (buffer)
IMPOSTAZIONI OPZIONALI:UX: Q5 / K8 / K9
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Componente di cont. solare: buffer K8 - Pompa anello scambio sec. K9BX: - Sonda collettore solare B6LP5840 (Comp. di controllo solare):- Valvola deviatriceLP5841 (Scambio solare esterno):- Sonda accumulo (buffer))
IMPOSTAZIONI OPZIONALI:UX: Q5 / K9
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Componente di controllo solare: piscina K18 BX: - Sonda collettore solare B6LP5840 (Comp. di controllo solare):- Pompa di carico
IMPOSTAZIONI OPZIONALI:UX: Q5 / K18
SOLARE TERMICO
Impianto ad un collettoreSOLARE TERMICO
Impianto ad un collettore
- 58 -
0
1
0
1
B6T
B6T
B6T
Q5
K8
K9
K18
Q5
Q5
K18
T
T
T
T
T
T
0
1
B6T
B6T
B6T
Q5
Q5
K9
K9
K18
K18
Q5
K8
K18
T
T
T
T
T
T
T
0
1
B6T
B6T
B6T
Q5
Q5
K9
K9
K18
K18
Q5
K8
K18
T
T
T
T
T
T
T
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Componente di controllo solare: piscina K18 BX: - Sonda collettore solare B6LP5840 (Comp. di controllo solare):- Valvola deviatrice
IMPOSTAZIONI OPZIONALI:UX: Q5
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Pompa anello scambio sec. K9- Componente di controllo solare: piscina K18BX: - Sonda collettore solare B6LP5840 (Comp. di controllo solare):- Sonda di carico
IMPOSTAZIONI OPZIONALI:UX: Q5 / K9 / K18
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Pompa anello scambio sec. K9- Componente di controllo solare: piscina K18BX: - Sonda collettore solare B6LP5840 (Comp. di controllo solare):- Valvola deviatrice
IMPOSTAZIONI OPZIONALI:UX: Q5 / K9
0
1
B6T
B6T
B6T
Q5
Q5
K9
K9
K18
K18
Q5
K8
K18
T
T
T
T
T
T
T
0101
B6T
B6T
T
T
T
T
T
T
Q5
Q5 K9
K8
K18
K18 K8010
1
B6T
B6T
T
T
T
T
T
T
Q5
Q5 K9
K8
K18
K18 K8
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Componente di cont. solare: buffer K8 - Componente di controllo solare: piscina K18 BX: - Sonda collettore solare B6LP5840 (Comp. di controllo solare):- Circolatore di carico
IMPOSTAZIONI OPZIONALI:UX: Q5 / K8 / K18
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Componente di cont. solare: buffer K8 - Componente di controllo solare: piscina K18 BX: - Sonda collettore solare B6LP5840 (Comp. di controllo solare):- Valvola deviatrice
IMPOSTAZIONI OPZIONALI:UX: Q5
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Componente di cont. solare: buffer K8 - Pompa anello scambio sec. K9- Componente di cont. solare: piscina K18BX: - Sonda collettore solare B6LP5840 (Comp. di controllo solare):- Pompa di carico LP5841 (Scambio solare esterno):- Insieme
IMPOSTAZIONI OPZIONALI:UX: Q5 / K8 / K9 / K18
SOLARE TERMICO
Impianto ad un collettore
SOLARE TERMICO
Impianto ad un collettore
- 59 -
IT
B6T
B6T
Q5
Q5 K9
K9
K8
K8
K18
K18
T
T
T
T
T
T
B6T
B6T
Q5
Q5 K9
K9
K8
K8
K18
K18
T
T
T
T
T
T
B6T
B6T
B6T
Q5
Q5
K9
K8K18
Q5
K9
K9
K8
K18
K8K18
T
T
T
T
T
T
T
T
T
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Componente di cont. solare: buffer K8 - Pompa anello scambio sec. K9- Componente di cont. solare: piscina K18BX: - Sonda collettore solare B6LP5840 (Comp. di controllo solare):- Valvola deviatrice LP5841 (Scambio solare esterno):- Insieme
IMPOSTAZIONI OPZIONALI:UX: Q5 / K9
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Componente di cont. solare: buffer K8 - Pompa anello scambio sec. K9- Componente di cont. solare: piscina K18BX: - Sonda collettore solare B6LP5840 (Comp. di controllo solare):- Pompa di carico LP5841 (Scambio solare esterno):- Accumulo sanitario
IMPOSTAZIONI OPZIONALI:UX: Q5 / K8 / K9 / K18
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Componente di cont. solare: buffer K8 - Pompa anello scambio sec. K9- Componente di cont. solare: piscina K18BX: - Sonda collettore solare B6LP5840 (Comp. di controllo solare):- Valvola deviatrice LP5841 (Scambio solare esterno):- Accumulo sanitario
IMPOSTAZIONI OPZIONALI:UX: Q5 / K9
B6T
B6T
B6T
Q5
Q5
K9
K8K18
Q5
K9
K9
K8
K18
K8K18
T
T
T
T
T
T
T
T
T
B6T
B6T
B6T
Q5
Q5
K9
K8K18
Q5
K9
K9
K8
K18
K8K18
T
T
T
T
T
T
T
T
T
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Componente di cont. solare: buffer K8 - Pompa anello scambio sec. K9- Componente di cont. solare: piscina K18BX: - Sonda collettore solare B6LP5840 (Comp. di controllo solare):- Sonda di carico LP5841 (Scambio solare esterno):- Sonda accumulo (buffer)
IMPOSTAZIONI OPZIONALI:UX: Q5 / K8 / K9 / K18
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Componente di cont. solare: buffer K8 - Pompa anello scambio sec. K9- Componente di cont. solare: piscina K18BX: - Sonda collettore solare B6LP5840 (Comp. di controllo solare):- Valvola deviatrice LP5841 (Scambio solare esterno):- Sonda accumulo (buffer)
IMPOSTAZIONI OPZIONALI:UX: Q5 / K9
SOLARE TERMICO
Impianto ad un collettore
SOLARE TERMICO
Impianto ad un collettore
- 60 -
T
B6 T T B61
Q5 Q16
B6 T T B61
Q5 Q16
T
K9
B6 T T B61
T
T
Q5 Q16
K8
B6 T T B61
Q5 Q16
T
T
K8
K9
T
B6 T T B61
Q5 Q16
B6 T T B61
Q5 Q16
T
K9
B6 T T B61
T
T
Q5 Q16
K8
B6 T T B61
Q5 Q16
T
T
K8
K9
T
B6 T T B61
Q5 Q16
B6 T T B61
Q5 Q16
T
K9
B6 T T B61
T
T
Q5 Q16
K8
B6 T T B61
Q5 Q16
T
T
K8
K9
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Pompa collettore solare 2 Q16BX: - Sonda collettore solare B6- Sonda collettore solare B61
IMPOSTAZIONI OPZIONALI:UX: Q5 / Q16
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Pompa collettore solare 2 Q16- Pompa anello scambio sec. K9BX: - Sonda collettore solare B6- Sonda collettore solare B61
IMPOSTAZIONI OPZIONALI:UX: Q5 / Q16 / K9
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Pompa collettore solare 2 Q16- Pompa di cont. solare: buffer K8BX: - Sonda collettore solare B6- Sonda collettore solare B61
IMPOSTAZIONI OPZIONALI:UX: Q5 / Q16
T
B6 T T B61
Q5 Q16
B6 T T B61
Q5 Q16
T
K9
B6 T T B61
T
T
Q5 Q16
K8
B6 T T B61
Q5 Q16
T
T
K8
K9
Sol38
Sol 39
B6 T T B61
Q5Q16
K8
K9
T
T
B6 T T B61
Q5Q16 K8
K9
T
T
Sol38
Sol 39
B6 T T B61
Q5Q16
K8
K9
T
T
B6 T T B61
Q5Q16 K8
K9
T
T
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Pompa collettore solare 2 Q16- Componente di cont. solare: buffer K8- Pompa anello scambio sec. K9BX: - Sonda collettore solare B6- Sonda collettore solare B61LP5840 (Comp. di controllo solare):- Pompa di carico LP5841 (Scambio solare esterno):- Insieme
IMPOSTAZIONI OPZIONALI:UX: Q5 / Q16 / K8 / K9
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Pompa collettore solare 2 Q16- Componente di cont. solare: buffer K8- Pompa anello scambio sec. K9BX: - Sonda collettore solare B6- Sonda collettore solare B61LP5840 (Comp. di controllo solare):- Valvola deviatrice LP5841 (Scambio solare esterno):- Insieme
IMPOSTAZIONI OPZIONALI:UX: Q5 / Q16 / K9
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Pompa collettore solare 2 Q16- Componente di cont. solare: buffer K8- Pompa anello scambio sec. K9BX: - Sonda collettore solare B6- Sonda collettore solare B61LP5840 (Comp. di controllo solare):- Circolatore di carico LP5841 (Scambio solare esterno):- Accumulo sanitario
IMPOSTAZIONI OPZIONALI:UX: Q5 / Q16 / K8 / K9
SOLARE TERMICO
Impianto a due collettori
SOLARE TERMICO
Impianto a due collettori
- 61 -
ITSol40
Sol41
B6 T T B61
Q5Q16
K8
K9
T
T
B6 T T B61
Q5Q16
K8
K9
T
T
Sol40
Sol41
B6 T T B61
Q5Q16
K8
K9
T
T
B6 T T B61
Q5Q16
K8
K9
T
T
Sol42
Sol44
B6 T T B61
Q5Q16
K18
T
T
B6 T T B61
Q5Q16 K18
K9
T
T
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Pompa collettore solare 2 Q16- Componente di cont. solare: buffer K8- Pompa anello scambio sec. K9BX: - Sonda collettore solare B6- Sonda collettore solare B61LP5840 (Comp. di controllo solare):- Valvola deviatrice LP5841 (Scambio solare esterno):- Accumulo sanitario
IMPOSTAZIONI OPZIONALI:UX: Q5 / Q16 / K9
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Pompa collettore solare 2 Q16- Componente di cont. solare: buffer K8- Pompa anello scambio sec. K9BX: - Sonda collettore solare B6- Sonda collettore solare B61LP5841 (Scambio solare esterno):- Sensore accumulo (buffer)
IMPOSTAZIONI OPZIONALI:UX: Q5 / Q16 / K9
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Pompa collettore solare 2 Q16- Componente di controllo solare: piscina K18BX: - Sonda collettore solare B6- Sonda collettore solare B61
IMPOSTAZIONI OPZIONALI:UX: Q5 / Q16
Sol42
Sol44
B6 T T B61
Q5Q16
K18
T
T
B6 T T B61
Q5Q16 K18
K9
T
T
Sol45
Sol46
B6 T T B61
Q5Q16
K18
K9
T
T
B6 T T B61
Q5Q16
K18 K9
T
T
T
Sol45
Sol46
B6 T T B61
Q5Q16
K18
K9
T
T
B6 T T B61
Q5Q16
K18 K9
T
T
T
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Pompa collettore solare 2 Q16- Pompa anello scambio sec. K9- Componente di controllo solare: piscina K18BX: - Sonda collettore solare B6- Sonda collettore solare B61LP5840 (Comp. di controllo solare):- Pompa di carico
IMPOSTAZIONI OPZIONALI:UX: Q5 / Q16 / K9 / K18
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Pompa collettore solare 2 Q16- Pompa anello scambio sec. K9- Componente di controllo solare: piscina K18BX: - Sonda collettore solare B6- Sonda collettore solare B61LP5840 (Comp. di controllo solare):- Valvola deviatrice
IMPOSTAZIONI OPZIONALI:UX: Q5 / Q16 / K9
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Pompa collettore solare 2 Q16- Componente di cont. solare: buffer K8- Componente di controllo solare: piscina K18BX: - Sonda collettore solare B6- Sonda collettore solare B61
IMPOSTAZIONI OPZIONALI:UX: Q5 / Q16
SOLARE TERMICO
Impianto a due collettori
SOLARE TERMICO
Impianto a due collettori
- 62 -
Sol48
Sol49 B6 T T B61
B6 T T B61
Q5Q16
Q5Q16
K18
K9
K8
K18
K9
K8
T
T
T
T
T
T
Sol48
Sol49 B6 T T B61
B6 T T B61
Q5Q16
Q5Q16
K18
K9
K8
K18
K9
K8
T
T
T
T
T
T
So l50
Sol51
B6 T T B61
Q5Q16
K18
K9
K8
T
T
T
B6 T T B61
Q5Q16
K18
K9
K8
T
T
T
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Pompa collettore solare 2 Q16- Componente di cont. solare: buffer K8- Pompa anello scambio sec. K9- Comp. di controllo solare: piscina K18BX: - Sonda collettore solare B6- Sonda collettore solare B61LP5840 (Comp. di controllo solare):- Pompa di carico LP5841 (Scambio solare esterno):- Insieme IMPOSTAZIONI OPZIONALI:UX: Q5 / Q16 / K8 / K9 / K18
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Pompa collettore solare 2 Q16- Componente di cont. solare: buffer K8- Pompa anello scambio sec. K9- Comp. di controllo solare: piscina K18BX: - Sonda collettore solare B6- Sonda collettore solare B61LP5840 (Comp. di controllo solare):- Valvola deviatrice LP5841 (Scambio solare esterno):- Insieme IMPOSTAZIONI OPZIONALI:UX: Q5 / Q16 / K9
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Pompa collettore solare 2 Q16- Componente di cont. solare: buffer K8- Pompa anello scambio sec. K9- Comp. di controllo solare: piscina K18BX: - Sonda collettore solare B6- Sonda collettore solare B61LP5840 (Comp. di controllo solare):- Pompa di carico LP5841 (Scambio solare esterno):- Accumulo sanitario IMPOSTAZIONI OPZIONALI:UX: Q5 / Q16 / K8 / K9 / K18
So l50
Sol51
B6 T T B61
Q5Q16
K18
K9
K8
T
T
T
B6 T T B61
Q5Q16
K18
K9
K8
T
T
T
T M/R
B6 T T B61
Q5Q16
K18
K9
K8
T
T
T
B63
B64
T
T
T
T M/R
B6 T T B61
Q5Q16
K18
K9
K8
T
T
T
B63
B64
T
T
T
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Pompa collettore solare 2 Q16- Componente di cont. solare: buffer K8- Pompa anello scambio sec. K9- Comp. di controllo solare: piscina K18BX: - Sonda collettore solare B6- Sonda collettore solare B61LP5840 (Comp. di controllo solare):- Valvola deviatrice LP5841 (Scambio solare esterno):- Accumulo sanitario IMPOSTAZIONI OPZIONALI:UX: Q5 / Q16 / K9
IMPOSTAZIONI NECESSARIE:QX: - Pompa collettore solare Q5- Pompa collettore solare 2 Q16- Componente di cont. solare: buffer K8- Pompa anello scambio sec. K9- Comp. di controllo solare: piscina K18BX: - Sonda collettore solare B6- Sonda collettore solare B61LP5841 (Scambio solare esterno):- Sonda accumulo (buffer) IMPOSTAZIONI OPZIONALI:UX: Q5 / Q16 / K9
IMPOSTAZIONI NECESSARIE:BX: - Sonda mandata solare B63 (alta temperatura)- Sonda ritorno solare B64 (bassa temperatura)
SOLARE TERMICO
Impianto a due collettori
SOLARE TERMICO
Impianto a due collettori
FUNZIONI EXTRA SOLARE TERMICO
- 63 -
IT
Sp1
01
01
Sp2
Sp4
Sp5
B4T
B42T
B41T
B4T
B42T
B41T
B4
Y4
Y4
T
B42T
B41T
B4T
B42T
B41T
Scambiatore
Sola
re
Scambiatore
Sola
re
0
1
0
1
K16
Valvola miscelatrice sul ritorno
Valvola parzializzatrice
Circolatore di tras ferimento
Electrical immersion heater buf fer
B4/B41/B42T
B73T
Y15
B4/B41/B42
B4
B41
T
Y15
Q11
B3/B31T T
T
B4 T
Sp1
01
01
Sp2
Sp4
Sp5
B4T
B42T
B41T
B4T
B42T
B41T
B4
Y4
Y4
T
B42T
B41T
B4T
B42T
B41T
Scambiatore
Sola
re
Scambiatore
Sola
re
0
1
0
1
K16
Valvola miscelatrice sul ritorno
Valvola parzializzatrice
Circolatore di tras ferimento
Electrical immersion heater buf fer
B4/B41/B42T
B73T
Y15
B4/B41/B42
B4
B41
T
Y15
Q11
B3/B31T T
T
B4 T
Sp1
01
01
Sp2
Sp4
Sp5
B4T
B42T
B41T
B4T
B42T
B41T
B4
Y4
Y4
T
B42T
B41T
B4T
B42T
B41T
Scambiatore
Sola
re
Scambiatore
Sola
re
0
1
0
1
K16
Valvola miscelatrice sul ritorno
Valvola parzializzatrice
Circolatore di tras ferimento
Electrical immersion heater buf fer
B4/B41/B42T
B73T
Y15
B4/B41/B42
B4
B41
T
Y15
Q11
B3/B31T T
T
B4 T
Sp1
01
01
Sp2
Sp4
Sp5
B4T
B42T
B41T
B4T
B42T
B41T
B4
Y4
Y4
T
B42T
B41T
B4T
B42T
B41T
Scambiatore
Sola
re
Scambiatore
Sola
re
0
1
0
1
K16
Valvola miscelatrice sul ritorno
Valvola parzializzatrice
Circolatore di tras ferimento
Electrical immersion heater buf fer
B4/B41/B42T
B73T
Y15
B4/B41/B42
B4
B41
T
Y15
Q11
B3/B31T T
T
B4 T
IMPOSTAZIONI NECESSARIE:BX: - Sonda accumulo (buffer) B4 LP4783 (Con integrazione solare):- No
IMPOSTAZIONI OPZIONALI:BX: - Sonda accumulo (buffer) B41- Sonda accumulo (buffer) B42
IMPOSTAZIONI NECESSARIE:QX: - Valvola deviatrice ritorno accumulo (buffer)Y15BX: - Sonda accumulo (buffer) B4- Sonda globale ritorno B73
IMPOSTAZIONI OPZIONALI:BX: - Sonda accumulo (buffer) B41- Sonda accumulo (buffer) B42
IMPOSTAZIONI NECESSARIE:BX: - Sonda accumulo (buffer) B4 LP4783 (Con integrazione solare):- Si
IMPOSTAZIONI OPZIONALI:BX: - Sonda accumulo (buffer) B41- Sonda accumulo (buffer) B42
IMPOSTAZIONI NECESSARIE:QX: - Valvola deviatrice ritorno accumulo (buffer)Y15BX: - Sonda accumulo (buffer) B4
IMPOSTAZIONI OPZIONALI:BX: - Sonda accumulo (buffer) B41- Sonda accumulo (buffer) B42
IMPOSTAZIONI NECESSARIE:QX: - Valvola d’intercettazione generatore dicaloreY4BX: - Sonda accumulo (buffer) B4 LP4783 (Con integrazione solare):- No
IMPOSTAZIONI OPZIONALI:BX: - Sonda accumulo (buffer) B41- Sonda accumulo (buffer) B42
IMPOSTAZIONI NECESSARIE:QX: - Trasferimento serbatoio Circolatore Q11
IMPOSTAZIONI OPZIONALI:BX: - Sonda sanitario B31
IMPOSTAZIONI NECESSARIE:QX: - Valvola d’intercettazione generatore dicaloreY4BX: - Sonda accumulo (buffer) B4 LP4783 (Con integrazione solare):- Si
IMPOSTAZIONI OPZIONALI:BX: - Sonda accumulo (buffer) B41- Sonda accumulo (buffer) B42
IMPOSTAZIONI NECESSARIE:QX: - Tampone riscaldatore K16
CONTROLLO TEMPERATURE ACCUMULO
Controllo temperatura buffer
CONTROLLO TEMPERATURE ACCUMULO
Funzioni extra controllo temperatura buffer
- 64 -
TWWSp1
TWWSp2
TB3
TB31
TB3
TB31
01
TWWSp4
TWWSp5
TWWSp13
TB3
TB31
T
B36
Q3
TB3
TB31
T
B36
Q3
TB3
TB31
Q3
Sola
re
01
TWWSp4
TWWSp5
TWWSp13
TB3
TB31
T
B36
Q3
TB3
TB31
T
B36
Q3
TB3
TB31
Q3
Sola
re
01
TWWSp4
TWWSp5
TWWSp13
TB3
TB31
T
B36
Q3
TB3
TB31
T
B36
Q3
TB3
TB31
Q3
Sola
re
01
TWWSp14
TWWSp16
TWWSp17
TB3
TB31
Q3
TB3
TB31
T
B35Q3
Y31/Y32
TB3
TB31
T
B35Q3Y31/Y32
Sola
re
Sola
re
TWWSp1
TWWSp2
TB3
TB31
TB3
TB31
IMPOSTAZIONI NECESSARIE:LP5093 (Con integrazione solare):- No LP5731:- Nessuno
IMPOSTAZIONI OPZIONALI:BX: - Sonda sanitario B31
IMPOSTAZIONI NECESSARIE:LP5093 (Con integrazione solare): - No LP5731 (Componente controllo sanitario Q3):- Pompa di carico
IMPOSTAZIONI OPZIONALI:BX: - Sonda sanitario B31 - Sonda di carico sanitrario B36 UX: - Pompa sanitario Q3
IMPOSTAZIONI NECESSARIE:LP5093 (Con integrazione solare): - Si LP5731 (Componente controllo sanitario Q3):- Pompa di carico
IMPOSTAZIONI OPZIONALI:BX: - Sonda sanitario B31 - Sonda di carico sanitrario B36 UX: - Pompa sanitario Q3
IMPOSTAZIONI NECESSARIE:LP5093 (Con integrazione solare):- Si LP5731 (Componente controllo sanitario Q3):- Nessuno
IMPOSTAZIONI OPZIONALI:BX: - Sonda sanitario B31
IMPOSTAZIONI NECESSARIE:LP5093 (Con integrazione solare): - No LP5731 (Componente controllo sanitario Q3):- Valvola deviatrice
IMPOSTAZIONI OPZIONALI:BX: - Sonda sanitario B31
IMPOSTAZIONI NECESSARIE:LP5093 (Con integrazione solare): - Si LP5731 (Componente controllo sanitario Q3):- Valvola deviatrice
IMPOSTAZIONI OPZIONALI:BX: - Sonda sanitario B31
ACCUMULO SANITARIO
Senza circolatore di caricoACCUMULO SANITARIO
Con circolatore di carico
ACCUMULO SANITARIO
Con valvola miscelatrice
- 65 -
IT
01
TWWSp14
TWWSp16
TWWSp17
TB3
TB31
Q3
TB3
TB31
T
B35Q3Y31/Y32
TB3
TB31
T
B35Q3Y31/Y32
Sola
re
Sola
re
TWWSp19
TWWSp20
T
B36
T
B36
TB3
TB3
TB31
TB31
Q33
Q33
Sola
re
TWWSp19
TWWSp20
T
B36
T
B36
TB3
TB3
TB31
TB31
Q33
Q33
Sola
re
TWWSp22
TWWSp23
T
B36
T
B36
TB3
TB31
TB3
TB31
Q33
Q3
Q33
Q3
Sola
re
TWWSp22
TWWSp23
T
B36
T
B36
TB3
TB31
TB3
TB31
Q33
Q3
Q33
Q3
Sola
re
01
TWWSp14
TWWSp16
TWWSp17
TB3
TB31
Q3
TB3
TB31
T
B35Q3Y31/Y32
TB3
TB31
T
B35Q3Y31/Y32
Sola
re
Sola
re
IMPOSTAZIONI NECESSARIE:MG (LP6014, 6015): - Controllo primario sanitario LP5093 (Con integrazione solare): - No
IMPOSTAZIONI OPZIONALI:BX: - Sonda sanitario B31
IMPOSTAZIONI NECESSARIE:QX: - Circolatore circuito intermedio sanitario Q33 LP5731 (Componente controllo sanitario Q3): - Nessuno LP5093 (Con integrazione solare): - No
IMPOSTAZIONI OPZIONALI:BX: - Sonda sanitario B31- Sonda di carico sanitrario B36 UX: - Pompa circuito intermedio sanitario Q33
IMPOSTAZIONI NECESSARIE:QX: - Pompa circuito intermedio sanitario Q33 LP5731 (Componente controllo sanitario Q3): - Nessuno LP5093 (Con integrazione solare): - Si
IMPOSTAZIONI OPZIONALI:BX: - Sonda sanitario B31- Sonda di carico sanitrario B36 UX: - Pompa circuito intermedio sanitario Q33
IMPOSTAZIONI NECESSARIE:QX: - Pompa circuito intermedio sanitario Q33 LP5731 (Componente controllo sanitario Q3): - Pompa di carico LP5093 (Con integrazione solare): - No
IMPOSTAZIONI OPZIONALI:BX: - Sonda sanitario B31- Sonda di carico sanitrario B36 UX: - Pompa circuito intermedio sanitario Q33- Pompa sanitario Q3
IMPOSTAZIONI NECESSARIE:QX: - Circolatore circuito intermedio sanitario Q33 LP5731 (Componente controllo sanitario Q3): - Circolatore di carico LP5093 (Con integrazione solare): - Si
IMPOSTAZIONI OPZIONALI:BX: - Sonda sanitario B31- Sonda di carico sanitrario B36 UX: - Pompa circuito intermedio sanitario Q33- Pompa sanitario Q3
IMPOSTAZIONI NECESSARIE:MG (LP6014, 6015): - Controllo primario sanitario LP5093 (Con integrazione solare): - Si
IMPOSTAZIONI OPZIONALI:BX: - Sonda sanitario B31
ACCUMULO SANITARIO
Con scambiatore di calore per carico accumulo
ACCUMULO SANITARIO
Con circolatore di carico e valvola miscelatrice
- 66 -
TWWSp25
TWWSp26
T
B36
TB3
TB31
Q33
Q3
T
B36
TB3
TB31
Q33
Q3
Sola
re
TWWSp25
TWWSp26
T
B36
TB3
TB31
Q33
Q3
T
B36
TB3
TB31
Q33
Q3
Sola
re
TWWSp28
TWWSp29
T
B36
TB3
TB31
Q33
Q3
Y31/Y32T
T
T
B36
TB3
TB31
Q33
Q3
Y31/Y32T
TB35
B35
Sola
re
TWWSp28
TWWSp29
T
B36
TB3
TB31
Q33
Q3
Y31/Y32T
T
T
B36
TB3
TB31
Q33
Q3
Y31/Y32T
TB35
B35
Sola
re
IMPOSTAZIONI NECESSARIE:QX: - Pompa circuito intermedio sanitario Q33 LP5731 (Componente controllo sanitario Q3): - Valvola deviatriceLP5093 (Con integrazione solare): - No
IMPOSTAZIONI OPZIONALI:BX: - Sonda sanitario B31- Sonda di carico sanitrario B36 UX: - Pompa circuito intermedio sanitario Q33
IMPOSTAZIONI NECESSARIE:QX: - Circolatore circuito intermedio sanitario Q33 LP5731 (Componente controllo sanitario Q3): - Valvola deviatriceLP5093 (Con integrazione solare): - Si
IMPOSTAZIONI OPZIONALI:BX: - Sonda sanitario B31- Sonda di carico sanitrario B36 UX: - Pompa circuito intermedio sanitario Q33
IMPOSTAZIONI NECESSARIE:MG/EM: - Controllo primario sanitario QX: - Pompa circuito intermedio sanitario Q33 LP5093 (Con integrazione solare): - No
IMPOSTAZIONI OPZIONALI:BX: - Sonda sanitario B31- Sonda di carico sanitrario B36 UX: - Pompa circuito intermedio sanitario Q33
IMPOSTAZIONI NECESSARIE:MG/EM: - Controllo primario sanitario QX: - Pompa circuito intermedio sanitario Q33 LP5093 (Con integrazione solare): - Si
IMPOSTAZIONI OPZIONALI:BX: - Sonda sanitario B31- Sonda di carico sanitrario B36 UX: - Pompa circuito intermedio sanitario Q33
FS
Input
FS Input Hx
TWWDl3
TWWDl8
Circolatore sanitario
Electrical immersion heater Accumulo sanitario
T
B38
Q34
T
B38
Q34
Y33/Y34
TB39
FST
B39
TB39
TB3
Q3
K6
Hx
Input Hx
Q4
Q4
FS
Input
FS Input Hx
TWWDl3
TWWDl8
Circolatore sanitario
Electrical immersion heater Accumulo sanitario
T
B38
Q34
T
B38
Q34
Y33/Y34
TB39
FST
B39
TB39
TB3
Q3
K6
Hx
Input Hx
Q4
Q4
FS
Input
FS Input Hx
TWWDl3
TWWDl8
Circolatore sanitario
Electrical immersion heater Accumulo sanitario
T
B38
Q34
T
B38
Q34
Y33/Y34
TB39
FST
B39
TB39
TB3
Q3
K6
Hx
Input Hx
Q4
Q4
FS
Input
FS Input Hx
TWWDl3
TWWDl8
Circolatore sanitario
Electrical immersion heater Accumulo sanitario
T
B38
Q34
T
B38
Q34
Y33/Y34
TB39
FST
B39
TB39
TB3
Q3
K6
Hx
Input Hx
Q4
Q4
IMPOSTAZIONI NECESSARIE:QX: - Pompa anello scambio primario Q34 BX: - Sonda mandata sanitario B38
IMPOSTAZIONI OPZIONALI:UX: - Pompa anello scambio primario Q34
Nota:- Necessita di accumulo sanitario
IMPOSTAZIONI NECESSARIE:MG (LP6014, 6015): - Riscaldatore istantaneo ACS QX: - Pompa anello scambio primario Q34 BX: - Sonda mandata sanitario B38
IMPOSTAZIONI OPZIONALI:BX: - Sonda circolazione sanitario B39
Nota:- Necessita di accumulo sanitario
IMPOSTAZIONI NECESSARIE:QX: - Pompa Q4
IMPOSTAZIONI OPZIONALI:BX: - Sonda circolazione sanitario B39
IMPOSTAZIONI NECESSARIE:QX: - Resistenza elettrica ACS K6
ACCUMULO SANITARIO
Con scambiatore di calore per carico accumulo
ACCUMULO SANITARIO
Con scambiatore di calore per produzione istantanea
- 67 -
ITSb1
Sb2
Sb3
Sb4
T
B13
T
B13
T
B13
Q15/Q19
T
B13
Q15/Q19
Separatore idrau l ico
HWe1
HWe2
HWe3
HWe4
HWe6
T
B10
T
B10
TB70
T
B10
TB70
Q25
T
B10
TB70
Q25
Y25/Y26
Separatore idrau l ico
HWe1
HWe2
HWe3
HWe4
HWe6
T
B10
T
B10
TB70
T
B10
TB70
Q25
T
B10
TB70
Q25
Y25/Y26
Separatore idrau l ico
HWe1
HWe2
HWe3
HWe4
HWe6
T
B10
T
B10
TB70
T
B10
TB70
Q25
T
B10
TB70
Q25
Y25/Y26
Separatore idrau l ico
HWe1
HWe2
HWe3
HWe4
HWe6
T
B10
T
B10
TB70
T
B10
TB70
Q25
T
B10
TB70
Q25
Y25/Y26
Separatore idrau l ico
HWe1
HWe2
HWe3
HWe4
HWe6
T
B10
T
B10
TB70
T
B10
TB70
Q25
T
B10
TB70
Q25
Y25/Y26
Sb1
Sb2
Sb3
Sb4
T
B13
T
B13
T
B13
Q15/Q19
T
B13
Q15/Q19
Sb1
Sb2
Sb3
Sb4
T
B13
T
B13
T
B13
Q15/Q19
T
B13
Q15/Q19
Sb1
Sb2
Sb3
Sb4
T
B13
T
B13
T
B13
Q15/Q19
T
B13
Q15/Q19
IMPOSTAZIONI NECESSARIE:BX: - Sonda piscina B13
IMPOSTAZIONI NECESSARIE:BX: - Sonda globale di mandata B10
IMPOSTAZIONI NECESSARIE:BX: - Sonda globale di mandata B10LP6600 (Indirizzo dispositivo):- 1 (cascata master)
IMPOSTAZIONI OPZIONALI:BX: - Sonda ritorno cascata B70
IMPOSTAZIONI NECESSARIE:LP6600 (Indirizzo dispositivo):- 2…16 (slave di cascata)
IMPOSTAZIONI NECESSARIE:QX: - Pompa cascata Q25 BX: - Sonda globale di mandata B10LP6600 (Indirizzo dispositivo):- 1 (master della cascata)
IMPOSTAZIONI OPZIONALI:BX: - Sonda ritorno cascata B70
IMPOSTAZIONI NECESSARIE:MG (LP6014, 6015): - Controllo temperatura di ritorno cascata BX: - Sonda globale di mandata B10LP6600 (Indirizzo dispositivo):- 1 (master della cascata)
IMPOSTAZIONI NECESSARIE:BX: - Sonda piscina B13
LP2080 (Con integrazione solare): - Si
IMPOSTAZIONI NECESSARIE:QX: - H1 Pompa Q15 o- H3 Pompa Q19 BX: - Sonda piscina B13HX: - Consenso piscina
IMPOSTAZIONI NECESSARIE:QX: - H1 Pompa Q15 o- H3 Pompa Q19 BX: - Sonda piscina B13HX: - Consenso piscinaLP2080 (Con integrazione solare): - Si
PISCINA SEPARATORE IDRAULICO
- 68 -
Note:
- 69 -
IT
Gentile Cliente,Ferroli S.p.A. La ringrazia per aver scelto il Pannello comandi Thermo EBM ed è fiduciosa che Lei abbia trovato in questo manuale tutte le informazioni a Lei necessarie.Per eventuali ulteriori Sue necessità contattare il Centro Assistenza Ferroli Autorizzato di competenza oppure il Servizio Assi-stenza Ferroli.
Con l’occasione riportiamo sinteticamente quanto stabilisce la Direttiva Europea 2002/96/EC sul corretto smaltimento dei prodotti elettrici ed elettronici.I prodotti elettrici o elettronici, alla fine della loro vita utile, NON DEVONO essere smaltiti insieme ai rifiuti urbani.Possono essere conferiti ai centri di raccolta differenziata, organizzati dalle amministrazioni, oppure riconsegnati ai rivenditori che forniscono questo servizio. Effettuare la raccolta differenziata evita il possibile inquinamento dell’ambiente, i rischi per la salute e permette il recupero di materiali con significativi risparmi. Il simbolo che indica la raccolta separata delle apparecchiature elettriche ed elettroniche è un contenitore di spazzatura mobile barrato come indicato.
- 70 -
INDEX
1. Introduction ................................................................................... pag. 71
2. Description of the panel ................................................................ pag. 71
3. Conformity ....................................................................................... pag. 71
4. Technical data .................................................................................. pag. 71
5. Supply and identification .................................................................. pag. 72
5.1 Accessories ............................................................................... pag. 72
6. Structure ........................................................................................... pag. 72
7. Management functions ..................................................................... pag. 73
8. Assembly/Installation ........................................................................ pag. 73
9. Wiring diagram ................................................................................. pag. 74
10. Key to symbols/wiring diagram components ................................... pag. 75
11. Connections to the controller ........................................................... pag. 76
12. Electrical connections panel-burner ................................................ pag. 77
12.1 Panel to single-stage burner ..................................................... pag. 77
12.2 Panel to two-stage burner ......................................................... pag. 77
12.3 Panel to 3-position modulating burner ...................................... pag. 78
12.4 Panel to Ferroli 3-position modulating burner ........................... pag. 78
13. Maximum system management ....................................................... pag. 79
14. Cascade boiler connection .............................................................. pag. 80
15. Probes .............................................................................................. pag. 81
16. Outside probe .................................................................................. pag. 81
17. AVS 37.294 interface ........................................................................ pag. 83
18. Setting and programming ................................................................ pag. 87
18.1 Initial startup .............................................................................. pag. 87
18.2 Language selection ................................................................... pag. 87
18.3 Time and date setting ............................................................... pag. 88
19. Programming .................................................................................... pag. 89
19.1 Procedure for accessing menu and submenu .......................... pag. 89
19.2 Procedure for accessing the submenus ................................... pag. 89
20. Burner management configuration ................................................... pag. 90
20.1 Modulating burner ..................................................................... pag. 90
21. Boiler operating limit configuration .................................................. pag. 91
21.1 Setting the boiler operating limits (OEM) .................................. pag. 91
22. Heating circuit management ............................................................ pag. 91
22.1 Mixing valve control .................................................................. pag. 92
22.2 Activating operation without the digital room control unit ......... pag. 92
23. Domestic hot water (DHW) management ......................................... pag. 93
23.1 Replenishment control .............................................................. pag. 93
23.2 Rapid heating of the DHW storage cylinder ............................. pag. 93
24. Climatic curves - temperature compensation .................................. pag. 94
24.1 Climatic curve adaptation ......................................................... pag. 94
25. Anti-condensation ............................................................................ pag. 95
25.1 Anti-condensation circulation configuration .............................. pag. 95
26. Configuration for cascade boiler management ................................ pag. 96
26.1 Overview of cascade boiler management strategy .................. pag. 97
27. Outlet temperature maintenance without room/outside temperature probes .... pag. 97
28. Supplementary solar thermal configurations .................................... pag. 98
28.1 Supplementary solar thermal with just one collector ................ pag. 98
28.2 Supplementary solar thermal with one collector and separate buffer tank ...... pag. 99
28.3 Supplementary solar thermal with two collectors ...................... pag. 99
28.4 Overview of settings for heating the DHW storage cylinder
by supplementary solar heat exchanger ...................................... pag. 100
28.5 Collector frost protection ........................................................... pag. 100
28.6 Collector overheat protection .................................................... pag. 100
29. Solid fuel boiler ................................................................................. pag. 101
29.1 Operating mode ........................................................................ pag. 101
29.2 Set point .................................................................................... pag. 101
29.3 Boiler / burner control ................................................................ pag. 101
30. Viewing and managing parameters ................................................. pag. 102
31. Error/fault codes ............................................................................... pag. 117
31.1 Error/fault codes ........................................................................ pag. 117
32. Examples of possible layouts (partial diagrams and auxiliary functions) .... pag. 119
32.1 Key ............................................................................................ pag. 119
32.2 Layouts ...................................................................................... pag. 120
- 71 -
GB
2. DESCRIPTION OF THE PANELThe Thermo EBM control panel is a temperature controller, fitted with probe for measuring the outside temperature, used to manage and control complex
systems made up of one or more boilers connected in a cascade, systems integrated with solar panels, and different types of heat generators.
Using the outside probe means only the heat needed to meet demand is generated, thus avoiding waste. As regards the heat generation appliances, the panel
can manage boilers with single-stage, two-stage and three-position or 0-10V modulating burners, while as regards the use of the heat generated, two mixed
systems, or one direct system plus a domestic hot water (DHW) storage cylinder.
3. CONFORMITY
4. TECHNICAL DATA
The Thermo EBM panel is compliant with:
- Low Voltage Directive 2006/95/EC
- Electromagnetic Compatibility Directive 2004/108/EEC
Power supply 230V - 50/60 Hz
Load control outputs 230V - 2A
Burner modulation relay 230V - 10A
Electrical protection IP 20
Fuse F 8A L 250V
Boiler safety thermostat 110 (0/-6)°C
Maximum current draw 8A
1. INTRODUCTIONThis manual is an addition to the instruction manual provided with appliances that the Thermo EBM control panel is installed on, and must therefore be
carefully kept for future reference.
Refer to these instruction manuals for details on prohibited actions and safety rules.
The panel must only be used for the purpose intended by Ferroli S.p.A.; the latter is not liable for any damage caused to people, animals or things as a result
of incorrect installation, adjustment or maintenance, or improper use.
WARNING
•TheThermoEBMpanelmustbeinstalledbyprofessionallyqualifiedpersonnelorbyFerroliauthorisedtechnicalservice,incompliancewiththe
national and local legislation in force.
•Inaddition,thesafety,installation,maintenanceandoperatinginstructionsprovidedinthismanualmustbecompliedwith.
PROHIBITED ACTIONS
•DONOTallowtheappliancetobecontrolledbychildrenorincapablepersonswithoutsupervision.
- 72 -
5. SUPPLY AND IDENTIFICATION
6. STRUCTURE
The Thermo EBM panel is supplied in a cardboard box.
It can be identified:
- by the label with the description and barcode on the packaging
- by the rating plate applied to the casing
The EBM Thermo Panel is composed of:
1-BoilerON/OFFswitch(SB1)andgreenindicatorlight(HL1)
2 - “Start burner” switch (SB2)
3 - Boiler safety thermostat (TSC), featuring manual reset, with reset button and red indicator light (HL2)
4 - AVS37.294 user interface
The packaging also contains:
- 1 instruction manual
-1outsideprobeQAC34/101(B9)(NTC1kΩ)
- 1 connection cable for Ferroli modulating burner
-1probeQAZ36(NTC10kΩ)
NOTE
Theboilersafetythermostat(TSC),theboileroutletprobeQAZ36(NTC10kΩ) and the
relay for 3-position modulation KA1 are already installed on the Thermo EBM panel.
After removing the packaging, check that the material supplied is intact and comple-
te; if this is not the case, contact Ferroli SpA or the Ferroli agency that sold the panel.
5.1 ACCESSORIES
-Cascademanifoldcollarprobekit(B10)QAD36/101(NTC10kΩ)
-ImmersionprobekitQAZ36(NTC10kΩ)
Controller RVS 63.238
Terminal block MP
Slots for inserting cables
Labels
Ratingplate
4 13 2
- 73 -
GB
7. MANAGEMENT FUNCTIONS
8. ASSEMBLY/INSTALLATION
To assemble the panel:
- Remove the two side screws and lift the cover.
- Fasten the panel to the boiler's casing using the 4 holes provided.
FUNCTION
HEAT GENERATOR SIDE SYSTEM DIDE
CR P -DIRECT
CR 1 -MIXED
CR 2 -MIXED
DHWPRODUCTIONMANAGEMENT
1
1-2
M
1
2
MAX
IMUM
CON
FIGU
RATI
ON
SINGLE-STAGEBURNERMANAGEMENT
TWO-STAGEBURNERMANAGEMENT
MODULATINGBURNERMANAGEMENT
BURNERMANAGEMENTFORBOILERSWITHCASCADECONNECTION
CLIMATECURVEOPERATION
MIXEDSYSTEMMANAGEMENTCOMBINEDWITHSOLIDFUELBOILER
MIXEDSYSTEMMANAGEMENTCOMBINEDWITHSOLARCOLLECTORS
WARNING: the panel must be fitted on the boiler.In all other cases, ensure adequate protection for the wiring and prevent access to live parts through the holes at the bot-tom of the appliance.
- 74 -
9. WIRING DIAGRAM
1
- 75 -
GB
10. KEY TO SYMBOLS/WIRING DIAGRAM COMPONENTS
Sim.\ Sym. Sigla \ Item Funzione \ Use type
B2BM
Sonda temperatura acqua mandata caldaia
Boiler water flow temperature probe
Sonda temperatura esterna
Outside temperature probe
Bruciatore
Burner
Lampada alimentazione pannello 230Vac
230Vac panel power supply lamp
Lampada allarme intervento termostato di sicurezza
Safety thermostat alarm lamp
Relè disponibile per bruciatore modulante a 3 punti
3-points modulation burner available relay
Regolatore RVS 63.283/109
RVS 63.283/109 regulator
Interfaccia operatore AVS 37.294
AVS 37.294 operator panel
Interruttore accensione pannello
Panel ignition switch
Interruttore consenso start bruciatore
Burner start switch consent
Termostato di sicurezza caldaia
Boiler safety thermostat
Segnale disponibile allarme TSC (230Vac)
TSC alarm available signal (230Vac)
BUS di comunicazione caldaie in cascata
Boiler cascade comunication BUS
B9BM
BU1BM
HL1QG
HL2QG
KA1QG
N1QG
N2QG
SB1QG
SB2QG
TSCQG
XT1BM
Signal for external Apparatus
Segnalazioni per Apparecchiature
esterne
Segnale a cascata a:Cascade Signal to:MASTER/SLAVE
RVS 63.283/109
XT2BM
- 76 -
11. CONNECTIONS TO THE CONTROLLER
RELAY OUTPUT (parameter 5894)
RELAY OUTPUT (parameter 5892)
RELAY OUTPUT (parameter 5891)
SYSTEM MIXING VALVE CR 2
SYSTEM PUMP CR 2
RELAY OUTPUT (parameter 5890)
SYSTEM PUMP CR 1
DHW STORAGE CYLINDER FILL PUMP
SYSTEM MIXING VALVE CR 1
BURNER CONNECTION(PRE-WIRED)
POWER SUPPLY(PRE-WIRED)
DIGITAL OUTPUT / 0-10V - (parameter 6070)
PROBE INPUT (parameter 5933)
PROBE INPUT (parameter 5932)
PROBE INPUT (parameter 5931)
PROBE INPUT (parameter 5930)
DIGITAL INPUT / 0-10V - (parameter 5960)
DIGITAL INPUT / 0-10V - (parameter 5950)
OUTSIDE PROBE
DHW STORAGE CYLINDER PROBE
BOILER OUTLET PROBE (ALREADY WIRED)
BOILER CASCADE BUS CONNECTION
CENTRAL HEATING OUTLET PROBE CR 2
061107B000020
RV
S63.283/109
1PR
VS
63.283/109
S061107000020
CENTRAL HEATING OUTLET PROBE CR 1
WARNINGS
The following are compulsory:
•Theuseofathermal-magneticcircuitbreakertodisconnectmainspower,minimumcontactopening3mm,compliantwithENstandards.
•Ensurethewiresareconnectedcorrectly,L(Live)-N(Neutral).
•Minimumwirecross-section1.5mm2.
•Leavetheearthwireatleast2cmlongerthantheL(Live)-N(Neutral)wires.
•Refertothewiringdiagramsinthismanualforanyoperationsontheelectricalsystem.
•Makesuretheapplianceiseffectivelyearthed(*).
•DONOTusethewaterpipestoearththeappliance.
(*)The manufacturer is not liable for any damage due to the failure to earth the appliance and to observe the information provided on the
wiring diagrams.
KEYLP: Line/parameterCR1: Central heating mixed circuit 1CR2: Central heating mixed circuit 2ACS: Domestic hot water circuit
- 77 -
GB
12. ELECTRICAL CONNECTIONS PANEL-BURNER
Installer connections.
12.1 PANEL TO SINGLE-STAGE BURNER
Series of enable burner ignition signals
Panel power supply230 Vac (8 A)
230 Vac boilersafety thermostat alarm signal max. 3 A
BURNER
12.2 PANEL TO TWO-STAGE BURNER
- 78 -
12.3 PANEL TO 3-POSITION MODULATING BURNER
230 Vac boilersafety thermostat alarm signal max. 3 A
BURNER BURNER MODULATION
Panel power supply230 Vac (8 A)
3-position burner modulation relay
12.4 PANEL TO FERROLI 3-POSITION MODULATING BURNER
230 Vac boilersafety thermostat alarm signal max. 3 A
Panel power supply230 Vac (8 A)
BURNER BURNER MODULATION
3-position burner modulation relayCable supplied
for Ferroli modular burner
Modulating control connectors
- 79 -
GB
13. MAXIMUM SYSTEM MANAGEMENT
IMPORTANT:
The system diagrams shown on this page are examples
onlyanddonotincludethesafetydevicesrequiredbyle-
gislation in force.
UTS
B9
Q3
B3ACS
RMB2
Q12 B7
TSC
B1
Q2
Y1/Y2
TSX
CR1
Q20
B12
Q6
Y5/Y6
TSX
CR2
CRP
ELECTRICAL CONNECTIONS TO THE RVS63.283
CONTROLLER
The mains power supply and boiler outlet probe (B2) are pre-
wired as standard.
The diagrams shown below illustrate the connections to be completed by the installer for maximum Thermo EBM panel system management.
061107B000020RVS63.283/109
1PRVS63.283/109
S061107000020
MY1/Y2 Q2Q6Q20Q12 Q3
B9 B3 B2B1B12
MY5/Y6
BURN
ER
POW
ER S
UPPL
Y
QX
2
BX
1
B7 H1
KEY
UTS Safety discharge
M Central heating flow outlet
R Central heating return inlet
Water circuit
Electrical connection
TSX System safety thermostat
(customer's responsibility)
CR1 Central heating mixed circuit 1
CR2 Central heating mixed circuit 2
CRP Central heating direct circuit
ACS Domestic hot water circuit
B2 Boiler outlet probe
B9 Outsideprobe
TSC Boiler safety thermostat
B3 Storage cylinder probe
Q3 Storage cylinder pump
B1 Central heating outlet probe (CR1)
Q2 Pump (CR1)
Y1/Y2 Mixing valve (CR1)
B12 Central heating outlet probe (CR1)
Q6 Pump (CR2)
Q12 Bypass pump boiler
Y5/Y6 Mixing valve (CR2)
Q20 Pump (CRP)
- 80 -
14. CASCADE BOILER CONNECTION
The Thermo EBM control panel allows the integrated management up to a maximum of 16 boilers with cascade connection.
Each boiler must be fitted with a control panel connected via BUS cable, according to the diagram shown on this page.
MASTER
B9
BOILER 1
BUS CONNECTION
BOILER 2 BOILER N
COMMON OUTLET MANIFOLD
COMMON RETURN MANIFOLD
B10
SLAVE SLAVE
Q1 Q1 Q1
B2 B2 B2
BOILER 1(master)
061107B000020RVS63.283/109
1PRVS63.283/109
S061107000020
Q1
BOILER 2(slave)
061107B000020RVS63.283/109
1PRVS63.283/109
S061107000020
BOILER 3(slave)
061107B000020RVS63.283/109
1PRVS63.283/109
S061107000020
BUS BUS BUS
BURNER POWER SUPPLY
QX
2
B9B10 B2 B2
Q1 Q1BURNER POWER SUPPLY BURNER POWER SUPPLY
QX
2
B2
KeyB2 Boiler outlet probeB9 OutsideprobeB10 Manifold outlet probeQ1 Boiler outlet pumps Water circuit Electrical connection
IMPORTANT: The system diagrams shown on this page are examples only and do not include the safety devices requiredbylegislationinforce.Connections for the burner, power supply, B2 boiler outlet probe are pre-wired as standard and to be repeated on each boiler in the cascade.
Connection/ConfigurationQ1 OnterminalQx2beingset-par.5891B10 OnterminalBx1beingset-par.5930
Note - Cascade connection between multiple boilers is also available with one circulating pump Q25 managed by the master controller. In this case, use one of the Qx outputs (for example Qx2) on the master controller to manage Q25, setting the corresponding parameter accordingly (for example, par. 5891). For further information, see the water circuit diagrams under “Examples of possible layouts” and “Viewing and managing parameters”.
Maximum allowed length of two-wire BUS LPB cables (copper)With BUS power supply from
controller (point-to-point) With central BUS power supply
Cable cross-section 1,5 mm2
Max length 250 m 460 m
Note - ObservethepolarityofthewiresintheBUSLPBcable.
- 81 -
GB
15. PROBES
16. OUTSIDE PROBE
The probes that can be used with the Thermo EBM panel are shown in the table.
For correct system operation, the probes must be correctly positioned and connected, and any conduits used for the connection cables must be separate
from those used for power cables (230 Vac).
LIST OF PROBES
For correct operation of the panel, the outside probe (B9) must be installed on the outside of the building being heated, following the instructions shown
on the probe's packaging. For the electrical connections between the outside probe and the Thermo EBM panel, use the dedicated terminals M-B9 on
the RVS 63-283 controller.
B1 Outletprobe(CR1) B22 Solid fuel boiler probe (outlet) B70 Cascade return probe
B2 Boiler probe (outlet) B31 DHW storage cylinder probe (bottom) B73 Primary circuit common return probe
B3 DHW storage cylinder probe (top) B35 DHW outlet temperature probe
B4 Buffer tank probe (top) B36 DHW probe fill (storage)
B6 Solar collector probe B38 Instant DHW heater outlet probe
B7 Boiler return probe B39 DHW circulation probe
B8 Flue gas temperature probe B41 Buffer tank probe (bottom)
B9 Outsideprobe B42 Buffer tank probe (middle)
B10 Common outlet probe (cascade) B61 2nd solar collector probe
B12 Outletprobe(CR2) B63 Solar outlet probe
B13 Pool probe B64 Solar return probe
WARNINGS
•Theprobeshouldbeinstalledonthenorthornorth-westsideofthebuilding
•Theprobeshouldbeplacedonasmoothsectionofthewall;intheeventofexposedbrickwallsorunevenwalls,asmoothcontactareashouldbeused.
•Theconnectioncablebetweentheprobeandcontrolpanelmustnothavejunctions;ifrequired,thesemustbesealedandadequatelyprotected.
•Anyconduitsusedfortheconnectioncablemustbeseparatefromthepowercables(230Vac).
Maximum allowed length of the probe cables (copper)
Cable cross-section 0,75 1,0 1,5 mm2
Max length 60 80 120 m
- 82 -
CROSS-REFERENCE TABLE
Temperature measured (°C) - Probe resistance value (Ω).
•OutsideprobeNTC1k Ω (B9)
T (°C) R (Ω) T (°C) R (Ω) T (°C) R (Ω) T (°C) R (Ω)-30,0 13’034 -9,0 4’358 12.0 1’690 33.0 740
-29,0 12’324 -8,0 4’152 13.0 1’621 34.0 713
-28,0 11’657 -7,0 3’958 14.0 1’555 35.0 687
-27,0 11’031 -6,0 3’774 15.0 1’492 36.0 663
-26,0 10’442 -5,0 3’600 16.0 1’433 37.0 640
-25,0 9’889 -4,0 3’435 17.0 1’375 38.0 617
-24,0 9’369 -3,0 3’279 18.0 1’320 39.0 595
-23,0 8’880 -2,0 3’131 19.0 1’268 40.0 575
-22,0 8’420 -1,0 2’990 20.0 1’218 41.0 555
-21,0 7’986 0.0 2’857 21.0 1’170 42.0 536
-20,0 7’578 1.0 2’730 22.0 1’125 43.0 517
-19,0 7’193 2.0 2’610 23.0 1’081 44.0 500
-18,0 6’831 3.0 2’496 24.0 1’040 45.0 483
-17,0 6’489 4.0 2’387 25.0 1’000 46.0 466
-16,0 6’166 5.0 2’284 26.0 962 47.0 451
-15,0 5’861 6.0 2’186 27.0 926 48.0 436
-14,0 5’574 7.0 2’093 28.0 892 49.0 421
-13,0 5’303 8.0 2’004 29.0 859 50.0 407
-12,0 5’046 9.0 1’920 30.0 827
-11,0 4’804 10.0 1’840 31.0 796
-10,0 4’574 11.0 1’763 32.0 767
- 83 -
GB
17. AVS 37.294 INTERFACE
The interface is provided to allow users, technical service and installers, hereinafter simply called “operators”, to perform the operations described on the
following pages.
The interface is connected via flat cable to the RVS 63.283 controller, and comprises:
OKESC
0 4 8 12 16 20 24
AUTO
DHW selection button
Display Operation modeselection button
Information
Confirm settings and/or changes made
Chimney sweep functionand/or SLT test
Manual operationCancel settings and/or changes made
Service connection (BSB)
Browsing, parameter setting,change values
Display
KeyHeating to comfort set point
Heating to reduced set point
Heating to frost protection set point
Processing running - please walt
Burner operating (oil/gas burner only)
Info level activated heating to reduced set point
Programming activated
HeatingtemporarilyOFFECOfunctionactive
Vacation function active
Reference to heating circuit
Maintenance / special operation
Error message
Xxxxxxxxxxxxxxxxxxxxxxxx
XxxxxxxxxxxxxxxxxxxxxxxxXxxxxxxxxxxxxxxxxxxxxxxx
INFO PROG ECO
No.8 8 8 8
1 8 8 8 8 81
- 84 -
Operating mode selection
Auto
Automatic operation
Automatic operation controls the room temperature based on the set time program.
Characteristics of automatic operation:
•Heatingmodebasedonthetimeprogram
•Temperaturesetpointaccordingto“Comfortsetpoint”or“Reducedsetpoint”
•Protectionfunctionsactive
•Automaticsummer/winterchangeover(ECOfunctions)
Continuous operation or
Continuous operation keeps the room temperature constant at the set level.
Heating to comfort setpoint
Heating to reduced setpoint
Characteristics of continuous operation:
•Heatingwithoutconsideringthetimeprogram
•Protectionfunctionsactive
•Automaticsummer/winterchangeoverand24hourheatinglimitnotactive,forcontinuousoperationwith
comfort setpoint
Protection mode
In protection mode the heating system is not active.
Are active the frost protection (must be connected the electrical power supply).
Characteristics of protection mode:
•Heatingoff
•Temperatureatthefrostprotectionsetpoint
•Protectionfunctionsactive
Auto
- 85 -
GB
DHW mode
•On:Thedomestichotwaterisheatedaccordingtothesettimeprogram
•Off:Thedomestichotwaterisnotheated;thefrostprotectionfunctionisactive
DHW mode can also be activated when the central heating circuits are in vacation mode.
Note
Ifrequired,thewaterinthestoragecylindercanbeheatedrapidlybyholdingthebuttonforaround
4 seconds.
DHW operating mode
Information
The information button:
a - if pressed briefly, from the main page, displays:
•Anyerrorormaintenancealarmmessages
•Anyspecialmessages
or
•Boilertemperature
•Outsidetemperature
•Minimumoutsidetemperature
•Maximumoutsidetemperature
•DHWtemperature
•Status of central heating circuit 1
•Status of central heating circuit 2
•Status of central heating circuit P
•DHWstatus
•Boilerstatus
•Solarheatingstatus
•Solidfuelboilerstatus
•Storagebufferstatus
•Time/date
•Customerservicetelephonenumber
b - if pressed for around 4 seconds, after pressing the button, accesses the menus.
temperatura ambiente
20.518:28
INFO
0 4 8 12 16 20 24
AUTO
Errore30: Sensore di flusso 1
02.0.1
INFO
0 4 8 12 16 20 24
AUTO
303: funzione spazzacamino
02.0.1
INFO
0 4 8 12 16 20 24
AUTO
room temperature
20.518:28
INFO
0 4 8 12 16 20 24
AUTO
Error30: Flow sensor 1
02.0.1
INFO
0 4 8 12 16 20 24
AUTO
303: chimney sweep function
02.0.1
INFO
0 4 8 12 16 20 24
AUTO
OK ESC
- 86 -
Special messages
Reset function
Manual control
Chimney sweep function
Thermostat test
Setpoint correction with manual control
The chimney sweep function is activated by pressing the button for around 3 seconds.
It enables an operating mode that allows the specialist to carry out analysis on the flue gas.
If there are special messages on the display, one of the following symbols is also shown:
Error message
A system error has occurred.
Press for further information.
Maintenance or special mode
A maintenance alarm has occurred, or the system has entered
special mode.
Press for further information.
ThefunctiontoresetthecountersandcertainparametersshouldONLYbeperformedbythemaintenancespecia-
list.Whenthisfunctionisavailable,thedisplayshowstheoptionsYes/No.
After the reset operation, the parameters return to the default settings.
When manual control is active, the relays are no longer activated and deactivated based on the set operating con-
ditions, but rather based on their specific functions, in accordance with the predefined manual operating status.
The burner relay, when activated in manual control, can be deactivated by the electronic temperature controller (TR).
yesReset ?
Manual control is activated by pressing the button; the display shows the symbol to denote maintenance/
specialmode.Presstodisplaytheinfoon“Manualcontrol”andsubsequentlymodifythesetpoint.
temperatura ambiente
20.518:28
INFO
0 4 8 12 16 20 24
AUTO
Errore30: Sensore di flusso 1
02.0.1
INFO
0 4 8 12 16 20 24
AUTO
303: funzione spazzacamino
02.0.1
INFO
0 4 8 12 16 20 24
AUTO
room temperature
20.518:28
INFO
0 4 8 12 16 20 24
AUTO
Error30: Flow sensor 1
02.0.1
INFO
0 4 8 12 16 20 24
AUTO
303: chimney sweep function
02.0.1
INFO
0 4 8 12 16 20 24
AUTO
temperatura ambiente
20.518:28
INFO
0 4 8 12 16 20 24
AUTO
Errore30: Sensore di flusso 1
02.0.1
INFO
0 4 8 12 16 20 24
AUTO
303: funzione spazzacamino
02.0.1
INFO
0 4 8 12 16 20 24
AUTO
room temperature
20.518:28
INFO
0 4 8 12 16 20 24
AUTO
Error30: Flow sensor 1
02.0.1
INFO
0 4 8 12 16 20 24
AUTO
303: chimney sweep function
02.0.1
INFO
0 4 8 12 16 20 24
AUTO
To test the boiler safety thermostat, press and hold the button.
The thermostat test must ONLY be performed by the maintenance specialist, as the water in the boiler is
heated to the maximum temperature.
NO other operators may perform this test.
- 87 -
GB
When starting the Thermo EBM panel for the first time:
18. SETTING AND PROGRAMMING
18.1 INITIAL STARTUP
18.2 LANGUAGE SELECTION
-Makesurethatthe“startburner”switch(2)isinthe“OFF”position
-Movethemainswitchonthesystemelectricalpanelto“ON”
- Press the switch (1) (green light on) to power up the panel
- Wait until the automatic system update is completed, when the “main page” is displayed.
If the main page is not shown, press
34 2 1
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
ItalianoSprache
PROG
No. 20
Unità di comando
ItalianoLingua
PROG
No. 20
Ora e dataUnità di comando
PROG
Ora e data
Ore / minuti
PROG
No. 1
01:2521.2
1
Temperatura caldaia
21.2
Ora e data
Ore / minuti
PROG
No. 1
14:17
Ora e data
Giorno / mese
PROG
No. 2
05:03
Ora e data
Anno
PROG
No. 3
2013
OK ESC
The information on the Thermo EBM control panel is organised into “pages and rows”. The following buttons are principally used to browse the information,
set the parameters, and set/modify the values:
To:
- select the desired rows/parameters
- modify the values and enable/disable the functions
To confirm the selected row and enter the corresponding page
To return to the previous page without saving any changes made
To:
- display information
- select the menu, if held for around 4 seconds, after having pressed the button from the “main page”
OK ESC
OK ESC
OK ESC
OK ESC
Press To enter the next page
Turn the knob To select “Bedieneinheit” (“Control unit”)
Press the button twice
To:- Confirm the selected row- Enter the language page (Sprache) and modify
the selected language (flashing)
Turn the knob To select the desired language (e.g. English)
Press To confirm the selected language
Press To return to the “end user” submenu
TheThermoEBMcontrolpanelisfactory-setforoperationinGerman.
Thelanguagecanbechanged,selectingfromthefollowingoptions:English,German,French,Italian,Dutch,Spanish,Portuguese,Danish,Finnish,Swedish.
To select the desired language, starting from the “main page”:
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
ItalianoSprache
PROG
No. 20
Unità di comando
ItalianoLingua
PROG
No. 20
Ora e dataUnità di comando
PROG
Ora e data
Ore / minuti
PROG
No. 1
01:2521.2
1
Temperatura caldaia
21.2
Ora e data
Ore / minuti
PROG
No. 1
14:17
Ora e data
Giorno / mese
PROG
No. 2
05:03
Ora e data
Anno
PROG
No. 3
2013
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
ItalianoSprache
PROG
No. 20
Unità di comando
ItalianoLingua
PROG
No. 20
Ora e dataUnità di comando
PROG
Ora e data
Ore / minuti
PROG
No. 1
01:2521.2
1
Temperatura caldaia
21.2
Ora e data
Ore / minuti
PROG
No. 1
14:17
Ora e data
Giorno / mese
PROG
No. 2
05:03
Ora e data
Anno
PROG
No. 3
2013
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
EnglishSprache
PROG
No. 20
Control unit
EnglishLanguage
PROG
No. 20
Time and dateControl unit
PROG
Time and date
Hours / minutes
PROG
No. 1
01:2521.2
1
Boiler temperature
21.2
Time and date
Hours / minutes
PROG
No. 1
14:17
Time and date
Day / month
PROG
No. 2
05:03
Time and date
Year
PROG
No. 3
2013
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
EnglishSprache
PROG
No. 20
Control unit
EnglishLanguage
PROG
No. 20
Time and dateControl unit
PROG
Time and date
Hours / minutes
PROG
No. 1
01:2521.2
1
Boiler temperature
21.2
Time and date
Hours / minutes
PROG
No. 1
14:17
Time and date
Day / month
PROG
No. 2
05:03
Time and date
Year
PROG
No. 3
2013
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
EnglishSprache
PROG
No. 20
Control unit
EnglishLanguage
PROG
No. 20
Time and dateControl unit
PROG
Time and date
Hours / minutes
PROG
No. 1
01:2521.2
1
Boiler temperature
21.2
Time and date
Hours / minutes
PROG
No. 1
14:17
Time and date
Day / month
PROG
No. 2
05:03
Time and date
Year
PROG
No. 3
2013
OK ESC
- 88 -
18.3 TIME AND DATE SETTING
Turn the knob
Turn the knob
To select the previous page
To select the “Time and date” row
Press the button twiceTo:- confirm the “Time and date” row- select the hours (flashing) and enable setting
Turn the knob
Press
Turn the knob
Press
To set the hours
To confirm the setting and go to the “minutes” (flashing)
To set the “minutes”
To confirm the setting
Turn the knob
Press
Turn the knob
Press
Turn the knob
Press
To select the current “day/month” page
To select the “month” (flashing)
To set the “current month” (e.g. 03)
To confirm the setting and go to the “day”
To set the “current day” (e.g. 05)
To confirm the setting
Turn the knob
Press
Turn the knob
Press
To select the “year” page
To select the “year” (flashing)
To set the current “year” (e.g. 2013)
To confirm the setting
Press the button twice To return to the main page
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
EnglishSprache
PROG
No. 20
Control unit
EnglishLanguage
PROG
No. 20
Time and dateControl unit
PROG
Time and date
Hours / minutes
PROG
No. 1
01:2521.2
1
Boiler temperature
21.2
Time and date
Hours / minutes
PROG
No. 1
14:17
Time and date
Day / month
PROG
No. 2
05:03
Time and date
Year
PROG
No. 3
2013
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
EnglishSprache
PROG
No. 20
Control unit
EnglishLanguage
PROG
No. 20
Time and dateControl unit
PROG
Time and date
Hours / minutes
PROG
No. 1
01:2521.2
1
Boiler temperature
21.2
Time and date
Hours / minutes
PROG
No. 1
14:17
Time and date
Day / month
PROG
No. 2
05:03
Time and date
Year
PROG
No. 3
2013
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
EnglishSprache
PROG
No. 20
Control unit
EnglishLanguage
PROG
No. 20
Time and dateControl unit
PROG
Time and date
Hours / minutes
PROG
No. 1
01:2521.2
1
Boiler temperature
21.2
Time and date
Hours / minutes
PROG
No. 1
14:17
Time and date
Day / month
PROG
No. 2
05:03
Time and date
Year
PROG
No. 3
2013
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
EnglishSprache
PROG
No. 20
Control unit
EnglishLanguage
PROG
No. 20
Time and dateControl unit
PROG
Time and date
Hours / minutes
PROG
No. 1
01:2521.2
1
Boiler temperature
21.2
Time and date
Hours / minutes
PROG
No. 1
14:17
Time and date
Day / month
PROG
No. 2
05:03
Time and date
Year
PROG
No. 3
2013
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
EnglishSprache
PROG
No. 20
Control unit
EnglishLanguage
PROG
No. 20
Time and dateControl unit
PROG
Time and date
Hours / minutes
PROG
No. 1
01:2521.2
1
Boiler temperature
21.2
Time and date
Hours / minutes
PROG
No. 1
14:17
Time and date
Day / month
PROG
No. 2
05:03
Time and date
Year
PROG
No. 3
2013
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
EnglishSprache
PROG
No. 20
Control unit
EnglishLanguage
PROG
No. 20
Time and dateControl unit
PROG
Time and date
Hours / minutes
PROG
No. 1
01:2521.2
1
Boiler temperature
21.2
Time and date
Hours / minutes
PROG
No. 1
14:17
Time and date
Day / month
PROG
No. 2
05:03
Time and date
Year
PROG
No. 3
2013
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
OK ESC
- 89 -
GB
19. PROGRAMMING
19.1 PROCEDURE FOR ACCESSING MENU AND SUBMENU
When switching on the panel, appears on the display the start screen.
Press button to directly access to the submenu reported below.
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
ItalianoSprache
PROG
No. 20
Unità di comando
ItalianoLingua
PROG
No. 20
Ora e dataUnità di comando
PROG
Ora e data
Ore / minuti
PROG
No. 1
01:2521.2
1
Temperatura caldaia
21.2
Ora e data
Ore / minuti
PROG
No. 1
14:17
Ora e data
Giorno / mese
PROG
No. 2
05:03
Ora e data
Anno
PROG
No. 3
2013
FINAL USER
SU
BM
ENU
Time and date
Control unit
Time program CR1
Time program CR2
Time program 4/ACS
Time program 5
Vacation CR1
Vacation CR2
Heating circuit 1
Heating circuit 2
Function maintenance/service
Diagnostic parameters
OK ESC
19.2 PROCEDURE FOR ACCESSING THE SUBMENUS
MENUEnd user Setup Specialist OEM
SU
BM
ENU
Time and date Time and date Time and date
Rese
rved
for F
ERRO
LI S
.p.A
.
Control unit Control unit Control unit
Time program CR1 Time program CR1 Time program CR1
Time program CR2 Time program CR2 Time program CR2
Time program 4/DHW Time program 4/DHW Time program 4/DHW
Time program 5 Time program 5 Time program 5
Vacation CR1 Vacation CR1 Vacation CR1
Vacation CR2 Vacation CR2 Vacation CR2
Central heating circuit 1 Central heating circuit 1 Central heating circuit 1
Central heating circuit 2 Central heating circuit 2 Central heating circuit 2
- - Boiler
- Configuration Configuration
- LPB LPB
- Fault Fault
Maint./service functions Maint./service functions Maint./service functions
- Input/output test Input/output test
- Status Status
Diagnostic parameters Diagnostic parameters Diagnostic parameters
- Unit diagnostics Unit diagnostics
1
Kesseltemperatur
Uhrzeit und Datum
Zeitprogramm Heizkreis 1Bedieneinheit
PROG
Bedieneinheit
DeutschSprache
PROG
No. 20
Bedieneinheit
ItalianoSprache
PROG
No. 20
Unità di comando
ItalianoLingua
PROG
No. 20
Ora e dataUnità di comando
PROG
Ora e data
Ore / minuti
PROG
No. 1
01:2521.2
1
Temperatura caldaia
21.2
Ora e data
Ore / minuti
PROG
No. 1
14:17
Ora e data
Giorno / mese
PROG
No. 2
05:03
Ora e data
Anno
PROG
No. 3
2013
When switching on the panel, the display shows the main page.
Press
Press and hold the button for 4 seconds to access the menus.
Turn the knob to select the desired menu.
Press to access the following submenus.
OK ESC
OK ESC
OK ESC
IMPORTANT: The OEM Menu is password-protected, while the Submenus and Lines/Parameters are reserved for Ferroli S.p.A.personnelONLY.
Ifanymodificationsarerequired,contactyourlocalauthorisedFerroliservicecentreortheFerroliservicedepartment.
- 90 -
Warning! Disconnect power before connecting the burner.
Make the electrical connections between the panel and burner as described in the paragraph on “panel-burner electrical connections”.
Warning! These settings must be made with the burner off and the panel powered.
Setup menu (Specialist) - Configuration submenu
20. BURNER MANAGEMENT CONFIGURATION
20.1 MODULATING BURNER
Installingamodulatingburnerrequiresoptimumflamecontrolsetting.
Prohibited! These settings must only be carried out by specialists (burner technician or Ferroli technical service).
The following parameters are password-protected (contact Ferroli technical service).
OEM menu (Password-protected) - Configuration submenu
Prog no. (on display)
Submenu parameter function Default setting Setup
5770 Type of heat generator 2 stage in relation to the type of burner
Damper actuator opening time. To ensure optimum control of the burner modulation system, the damper actuator opening time needs to be configured.
Example: Damper actuator opening time (90°) = 120 seconds Minimum damper actuator position = 20° Maximum damper actuator position = 80° Therefore, the effective opening time of the burner air damper actuator used to control modulation is as follows:
120 s x (80°-20°) = 80 s 90° Positioning pulses: Damper position is controlled by pulse signals. The minimum pulse duration in relation to damper actuator opening time is defined as follows: Actuator opening time TS Minimum pulse duration 7.5 s - 14.5 s around 200 ms 15 s - 29.5 s around 300 ms 30 s - 59.5 s around 500 ms 60 s - 119.5 s around 1.10 s > 120 s around 2.20 s
Modulation Xp. Xp affects the proportional action of the controller.
Setting the proportional band correctly ensures that burner modulation will adapt to the behaviour of the system.
Modulation Tn. Tn affects the integral action of the controller.
Setting the integral time correctly ensures that burner modulation will adapt to the behaviour of the system.
Modulation Tv. Tv affects the derivative action of the controller. When Tv = 0, the derivative action is disabled.
Setting the derivative time correctly ensures that burner modulation will adapt to the behaviour of the system.
Prog no. (on display)
Reference menu
Submenu parameter function Default setting
RangeUnit of
measureMin Max
Boiler
2232 OEM Damper actuator opening time 60 7.5 480 s
2233 OEM Modulation Xp 20 1 200 °C
2234 OEM Modulation Tn 150 10 873 s
2235 OEM Modulation Tv 4.5 0 30 s
- 91 -
GB
It is recommend to check parameters 2210 (minimum boiler temperature set point limit) and 2212 (maximum boiler temperature set point limit).
These should be set according to the needs of the system.
Specialist menu - Boiler submenu
21. BOILER OPERATING LIMIT CONFIGURATION
Prog no. (on display) Submenu parameter function Default setting Setup
2210 Minimum set point 40°C 40°C
2212 Maximum set point 80°C 80°C
See the complete list of controller parameters for further information.
22. HEATING CIRCUIT MANAGEMENT
Below are some suggestions and instructions for setting up mixed central heating systems. For connection of the central heating outlet probes, circulating
pumpsandmixingvalvesonsystemsCR1andCR2,seetheparagraph“MAXIMUMSYSTEMMANAGEMENT”.
Warning! Disconnect power to the panel before connecting the probes and the loads.
Warning! Before activating burner operation, check whether the mixed heating circuits use underfloor heating. The maximum circuit outlet tem-
perature (see the following table) must be set as specified by the manufacturer of the flooring. Correct operation is only ensured in systems that
are correctly installed (water circuit, electrical installation, parameter settings). Failing to heed the above warnings may cause damage to the floor!
For “ready to lay” heating systems, the “floor screed function” can be used. This allows certain temperature profiles to be managed over time (for
further information, see the complete list of parameters and/or contact the Ferroli service department).
Setup menu (Specialist) - Heating circuit CR1, CR2, CRP submenu
21.1 SETTING THE BOILER OPERATING LIMITS (OEM)
In special situations, when available on the specific model of boiler, a higher maximum operating temperature and/or a lower minimum operating temperature
thanthedefaultvaluescanbeset.Asalreadydescribed,parameters2210and2212canbesettoadaptoperationaccordingtorequirementsofthesystem.
These parameters can be set within certain limits. These limits are represented by parameters 2211 and 2213. The parameters are password-protected,
any changes must be made by the manufacturer.
Prohibited! These settings must only be carried out by specialists (installer or Ferroli technical service).
The following parameters are password-protected (contact Ferroli technical service).
OEM menu (Password-protected) - Boiler submenu
Minimum / maximum operating temperatures - OEM. These represent the lower and upper limits for setting parameters 2210 and 2212.
Prog no. (on display)
Reference menu
Submenu parameter function Default setting
RangeUnit of
measureMin Max
Boiler
2211 OEM Minimumoperatingtemperature-OEM 40 8 95 °C
2213 OEM Maximumoperatingtemperature-OEM 85 8 120 °C
Prog no. (on display)
Submenu parameter function Default setting Setup
740, 1040, 1340Minimum outlet temperature set point CR1, CR2, CRP
8°C 8°C
741, 1041, 1341Maximum outlet temperature set point CR1, CR2, CRP
80°CSet based on the maximum system
temperature allowed
- 92 -
If needing to manage an additional direct heating system, one of the QX outputs can be used, setting this as the power supply or enabling signal for the
direct circuit pump Q20 (see the following table and the complete list of parameters).
Prog no. (on display)
Submenu parameter function Default setting Setup
5710 Central heating circuit 1 On On/Offbasedonrequirements
5715 Central heating circuit 2 On On/Offbasedonrequirements
Setup menu (Specialist) - Configuration submenu
Prog no. (on display)
Submenu parameter function Default setting Setup
5890, 5891, 5892, 5894 Relay output QX1, QX2, QX3, QX4 None Pump CRP Q20
N.B. QX1, QX2 and QX3 are 230 Vac outputs, while QX4 has voltage-free changeover contacts (the common is FX4).
Setup menu (Specialist) - Configuration submenu
22.1 MIXING VALVE CONTROL
If mixing valves are used in the mixed heating circuits, the following parameters need to be checked and modified if necessary:
Prog no. (on display)
Submenu parameter function Default setting Setup
830, 1130 Boost mixing valve 5°C Configure according to needs
832, 1132 Type of actuator 3-position3-position or 2-position, depending
on the type of actuator
833, 1133 2-pos switching differential 2°CCheck the characteristics of the 2-position actuator
834, 1134 Actuator travel time 120s Check the characteristics of the actuator
Select the type of actuator (“3-position” or “2-position”), and if using a “2-position” actuator”, the changeover differential must be set based on to the
characteristics of the actuator. For correct mixing, the current boiler outlet temperature must be greater than the mixing valve outlet temperature set
point; otherwise, this temperature may not be controlled. The controller generates the boiler outlet temperature according to the increase set here, and
according to the current outlet set point. Adapt the controller activation time (parameters 834 and/or 1134) according to the actuator travel time (refer to
the characteristics of the actuator).
22.2 ACTIVATING OPERATION WITHOUT THE DIGITAL ROOM CONTROL UNIT
Boiler operation without the digital room control unit digital is activated via inputs H1 and H3 on the controller.
Thecontrollerisalreadyconfiguredforcontinuousboileroperation.Nonetheless,roomthermostats(normally-opencontacts)canbeconnectedtoH1and/
or H3 to enable operation only when there is heating demand. A number of settings need to be applied to the selected input, H1 or H3, such as the type of
actionandthelogicofthecontact(NO“normallyopen”orNC“normallyclosed”).Forexample,toactivateoperationbasedonroomtemperature,connect
the normally-open contact from the room thermostat to input H1 (see the paragraph “Maximum system management”) and set the following parameters:
Specialist menu - Heating circuit CR1, CR2 submenu
Prog no. (on display)
Submenu parameter function Default setting Setup
5950 Input H1 functionChange operating mode
CH+DHWChange operating mode CH
5951 Contact H1 logic Normallyopen Normallyclosed
N.B.Heatingisrequiredwhenthethermostatcontactcloses.
OnlycircuitsCR1,CR2orCRPcanbeset,bysuitablymodifyingthevalueofparameter5950(seethecompletelistofparameters).
The same action can be carried out by H3 (see parameters 5960 and 5961).
Setup menu (Specialist) - Configuration submenu
Activate or deactivate CR1 and/or CR2 according to the type of system
- 93 -
GB
List of parameters to be set for DHW management.
Setup menu (Specialist) - Configuration submenu
23. DOMESTIC HOT WATER (DHW) MANAGEMENT
Prog no. (on display)
Submenu parameter function Default setting Setup
5730 DHW sensor B3 Probe Probe or thermostat in relation to the sensor used
5731 DHW actuator Q3 Fill pump Fill pump or selector valve in relation to the type of system
Prog no. (on display)
Submenu parameter function Default setting Setup
1610 Standard set point 55°C Configure according to needs
Setup menu (All) - DHW submenu
Prog no. (on display)
Submenu parameter function Default setting Setup
1612 Reduced set point 40°C Configure according to needs
Setup menu (Specialist) - DHW submenu
DHW operation is managed by the set time program, “Time program 4/DHW” (see the complete list of parameters).
23.1 REPLENISHMENT CONTROLActivation of the DHW heating cycle to reach the nominal or reduced set point is managed in relation to a set temperature differential. When the temperature measured by the DHW probe (B3) falls below the effective set point by a temperature value greater than the differential (parameter 5024), DHW heating is activated until reaching the set point. This differential can be modified by the manufacturer (password-protected).
Warning! These settings must only be carried out by specialists (installer or Ferroli technical service).
The following parameters are password-protected (contact Ferroli technical service).
OEM menu (Password-protected) - DHW storage submenu
Prog no. (on display)
Referencemenu
Submenu parameter function Default setting
RangeUnit of
measureMin Max
Boiler
5024 OEM Changeover differential 5 0 20 °C
23.2 RAPID HEATING OF THE DHW STORAGE CYLINDERAsshownintheparagraph“AVS37.294INTERFACE-DHWoperatingmode”,rapidheatingoftheDHWstoragecylinderfromthereducedsetpointcanbe activated by pressing the dedicated button for 4 seconds. The heating cycle only lasts until reaching the standard set point, after which the water is heated again to the reduced set point. Rapid heating of the DHW storage cylinder can also be managed automatically, depending on the setting of parameter 5070 (see the following table).
Warning! These settings must only be carried out by specialists (installer or Ferroli technical service).
The following parameters are password-protected (contact Ferroli technical service).
OEM menu (Password-protected) - DHW storage submenu
Prog no. (on display)
Reference menu
Submenu parameter function Default setting
RangeUnit of
measureMin Max
Boiler
5070 OEM Automatic rapid heating Off ¦ On
On -
Automatic rapid heating. Rapid DHW heating can be activated manually or automatically. In this case, the DHW is heated for a certain time until reaching the standard set point.
Off. Rapid DHW heating must be activated manually.
On. If the DHW temperature falls below the reduced set point (parameter 1612) by at least 2 times the changeover differential (parameter 5024), rapid heating
will be activated until reaching the standard DHW set point (parameter 1610).
Note: Automatic rapid DHW heating is only operational when DHW operating mode is activated.
- 94 -
24. CLIMATIC CURVES - TEMPERATURE COMPENSATIONThe outside probe can be used to operate the boiler in temperature compensation mode, in other words, supply the systems at the optimum temperature,
calculatedbasedontheoutsidetemperature.OntheThermoEBMpanel,themostsuitableclimaticcurveforeachheatingcircuitcanbeselected.Theselected
climatic curve refers to a room temperature set point of 20°C. If the room temperature set point is modified, the climatic curves are adapted automatically.
The default settings are:
Parameter 720 (CR1 mixed): 1,5
Parameter 1020 (CR2 mixed): 1,5
Parameter 1320 (CRP direct): 1,5
20 10
100
90
80
70
60
50
40
30
0 -10 -20 -30
0,25
0,5
0,75
1
1,25
1,5
1,75
2
4 3,5 3 2,75 2,5 2,25
°C
°C
24.1. CLIMATIC CURVE ADAPTATIONInformation on adjusting the climatic curves for central heating circuits provided below.
End user menu - Heating circuit CR1, CR2, CRP submenu
Prog no. (on display)
Submenu parameter function Default setting Setup
720, 1020, 1320 Characteristic curve slope 1.5Setbasedonrequirementsand system characteristics
The heating curve is used to determine the best outlet temperature set point to ensure an outlet temperature that is suitable for the climatic conditions.
The curve can be adjusted by setting certain parameters, so as to adapt heat production and the room temperature according to specific needs.
Characteristic curve slope. If the room temperature is not suitable at low outside temperatures but is suitable at high outside temperatures, the slope of the curve needs to be adjusted. - Increase the slope: This increases the outlet temperature, especially in the event of low outside temperatures. - Decrease the slope: This decreases the outlet temperature, especially in the event of low outside temperatures. Note: The default heating curve refers to a room temperature set point of 20°C. If the room temperature set point is modified, the heating curves are automatically adapted to the new value.
Parallel offset of the curve Parallel offset of the heating curve uniformly shifts the outlet temperature along the scale of outside temperatures. In other words, if the room temperature is always too high or too low, the curve can be corrected by shifting it sideways inside the graph.
Adaptation of the curve Adaptation of the heating curve means the controller can automatically adapt the curve based on prevalent climatic conditions. In this case, adjustments
totheslopeand/orparalleloffsetofthecurvearenotrequired.Thefunctioncanonlybeactivatedordeactivated(“on”or“off”). Note: The function is useful when: - at least one digital room control unit is connected to the controller; - “room temperature influence” is set to a value between 1 and 99; -nothermostaticvalvesareinstalledintheroominquestion(thesamewheretheroomtemperaturesensorisinstalled).Iftherearethermostatic
valves, these must be adjusted to the fully open position.
Specialist menu - Heating circuit CR1, CR2, CRP submenu
Prog no. (on display)
Submenu parameter function Default setting Setup
721, 1021, 1321 Curve offset 0Setbasedonrequirementsand system characteristics
726, 1026, 1326 Curve adaptation OffSetbasedonrequirementsand system characteristics
- 95 -
GB
25. ANTI-CONDENSATIONTo best manage system operation, it is recommended to install an anti-condensation pump and immersion return probe “B7”, inserted in a probe socket on
thereturnpipe,atadistanceequalto3-5diametersupstreamofanywaterconnections.
Alternatively, a strap-on probe with similar characteristics can be used.
NOTE: The minimum return temperature to the boiler (anti-condensation circulation) can be maintained using a mixing valve with three-position control.
In this case, probe B7 needs to be fitted in a different position. In fact, this must measure the mixed water temperature in the return pipe to the
boiler. Instead of pump Q12, a mixing valve with suitable characteristics will be used, connecting it to outlet Y1/Y2 or Y5/Y6 on the controller. Set
parameter 6014 (“Mix unit 1 function”) or parameter 6015 (“Mix unit 2 function”) to “Return temperature control”. For further information, see the
water circuit diagrams under the paragraph “Examples of possible layouts (partial diagrams and auxiliary functions)” and the paragraph “Viewing
and managing parameters”.
NOTE: The use of a mixing valve to maintain the return temperature reduces the maximum number of mixed heating circuits that can be
managed (one rather than two).
Q 12D
B 7
3 ÷
5 D
25.1 ANTI-CONDENSATION CIRCULATION CONFIGURATION
ManagementoftherecirculatingwaterpumpintheboilerQ12tomaintainboilerreturntemperature,aboveallintransientstagesofoperation,requires
severalsettings.OneoftheQXoutputscanbeused,settingitasthepowersupplyorenablingsignalforoperationofthebypass pump Q12. The return
temperature probe B7 must be connected to one of the free BX inputs, programming this accordingly. For information on programming, see the following
table and the complete list of parameters.
Setup menu (Specialist) - Configuration submenu
Prog no. (on display)
Submenu parameter function Default setting Setup
5890, 5891, 5892, 5894 Relay output QX1, QX2, QX3, QX4 None Bypass pump Q12
5930, 5931, 5932, 5933 Probe input BX1, BX2, BX3, BX4 None Return probe B7
N.B. QX1, QX2 and QX3 are 230 Vac outputs, while QX4 has voltage-free changeover contacts (the common is FX4).
Specialist menu - Boiler submenu
Prog no. (on display)
Submenu parameter function Default setting Setup
2270 Minimum return set point 8°CSet in relation to the type of fuel
andtheminimumrequiredreturn temperature in the boiler
- 96 -
26. CONFIGURATION FOR CASCADE BOILER MANAGEMENT
Managementofmultipleheatgeneratorsinacascaderequiresanumberofsettings,accessoriesandelectricalconnections,asshownonthegeneralcon-
nection diagram. As concerns the Master controller, connect the common boiler outlet probe B10 to one of the BX inputs available.
Also connect the outside temperature probe B9 to the dedicated input.
Naturally,theMasterandSlavepanelsmustalsobeconnectedtotheboileroutletprobeB2andboilercirculatingpumpQ1.
The controllers communicate with one another via BUS LPB, using terminals MB and DB (respectively “LPB earth” and “LPB data”), respecting the polarity
and the cross-sections of the electrical cables according to the length (see the table of specifications).
Each boiler controller will be identified by a specific address, which must be chosen during setup.
Note: If deciding to use just one circulating pump Q25 for the entire cascade of boilers, this must be connected to the Master controller (see the complete
list of parameters and the complete list of circuit configurations).
MASTER CONTROLLER
Setup menu (Specialist) - Configuration submenu
Prog no. (on display)
Submenu parameter function Default setting Setup
5890, 5891, 5892, 5894 Relay output QX1, QX2, QX3, QX4 None Boiler pump Q1
5930, 5931, 5932, 5933 Probe input BX1, BX2, BX3, BX4 None Common outlet probe B10
N.B. QX1, QX2 and QX3 are 230 Vac outputs, while QX4 has voltage-free changeover contacts (the common is FX4).
Setup menu (Specialist) - LPB submenu
Prog no. (on display)
Submenu parameter function Default setting Setup
6600 Appliance address 10 for stand-alone appliance
1
SLAVE CONTROLLER
Setup menu (Specialist) - Configuration submenu
Prog no. (on display)
Submenu parameter function Default setting Setup
5890, 5891, 5892, 5894 Relay output QX1,QX2, QX3, QX4 None Boiler pump Q1
N.B. QX1, QX2 and QX3 are 230 Vac outputs, while QX4 has voltage-free changeover contacts (the common is FX4).
Setup menu (Specialist) - LPB submenu
Prog no. (on display)
Submenu parameter function Default setting Setup
6600 Appliance address 1(0 for stand-alone appliance)
2,3... 16 according to the number of heat generators
- 97 -
GB
26.1 OVERVIEW OF CASCADE BOILER MANAGEMENT STRATEGY
Below is a list of some parameters that may be useful for more efficient management of the cascade connection between boilers.
Prog no. (on display)
Submenu parameter function
3532 Disable restart
3533 Delay on starting
3540 Automaticsourcesequence
3541 Excludesourcefromautomaticsequence
3544 Main source
Disable restart This prevents a deactivated heat source from being activated again before a set time interval. Consequently,itavoidsexcessivelyfrequentswitchingoftheheatsourceandguaranteesmorestablesystemoperation.
Delay on starting Correctly setting the delay on starting ensures that system operation remains more stable. Itavoidsfrequentswitchingoftheheatsource. Regarding to DHW demand, the delay time is fixed at 1 minute
Automatic source sequence The order of priority can be set between the different sources:
- Fixed order: The setting − − − defines a fixed order for switching on/off. In this case, the main heat source can be selected by setting parameter 3544, while the remaining heat sources will be switched on or off in the same
order as the addresses set on the LPB device.
- Order based on the number of operating hours The number of hours at which the boiler activation priority is changed over can be set. The default setting is 500 hours. The priority changes according to the order of device addresses.
Exclude source from automatic sequence Thiscanonlybeusedincombinationwiththe“Automaticsourcesequence”parameter(3540). It is used to exclude the first and/or the last heat source from automatic switching.
Main source Thiscanonlybeusedincombinationwiththe“Automaticsourcesequence”parameter(3540). The heat source defined as the main heat source is always the first to be switched on and the last to be switched off. The other sources of heat are switched on and off in the same order as the addresses set on the LPB device.
Specialist menu - Cascade boiler submenu
27. OUTLET TEMPERATURE MAINTENANCE WITHOUT ROOM/OUTSIDE TEMPERATURE PROBESIn certain cases, the temperature in a hot water distribution circuit needs to be kept constant, even when there is no demand from a room thermostat or
outside temperature probe. Heat production can be provided by one boiler (“stand-alone” configuration) or by a series of boilers connected in a cascade
(“cascade” configuration). In the latter case, the same rules as described in the paragraph “Cascade boiler management” apply. Circuits CR1, CR2, if not
used, must be deactivated (LP5710 and LP5715). To do this, use inputs H1 and H3, setting the corresponding parameters as shown in the following table:
Setup menu (Specialist) - Configuration submenu
Prog no. (on display)
Submenu parameter function Default setting Setup
5950, 5960 Input H1, H3 functionChange operating mode
CH+DHWMinimum outlet set point
5951, 5961 Contact H1, H3 logic Normallyopen Normallyopen
5952, 5962 Minimum outlet set point H1, H3 70°CSetbasedonrequirementsand system characteristics
Connect switches to inputs H1 and/or H3.When the switch contacts close, heat production will be activated.
Continuous heat production can be activated by jumpering inputs H1 and/or H3.
Simply connect the switch or jumper to just one of the two inputs specified above to activate the system.
- 98 -
28.1 SUPPLEMENTARY SOLAR THERMAL WITH JUST ONE COLLECTOR
B31
B3
B6
Q5
Setup menu (Specialist) - Configuration submenu
Prog no. (on display)
Submenu parameter function Default setting Setup
5890, 5891, 5892, 5894 Relay output QX1,QX2, QX3, QX4 None Collector pump Q5
5930, 5931, 5932, 5933 Probe input BX1,BX2, BX3, BX4 None Collector probe B6
5930, 5931, 5932, 5933 Probe input BX1,BX2, BX3, BX4 None DHW probe B31
N.B. QX1, QX2 and QX3 are 230 Vac outputs, while QX4 has voltage-free changeover contacts (the common is FX4).
28. SUPPLEMENTARY SOLAR THERMAL CONFIGURATIONThe circuit configurations and the list of parameters to be configured for integrated management of certain types of solar heating systems are enclosed.
Theprobesandcirculatingpumpsrequiredshouldbepositionedasshownintheencloseddiagrams.
Setup menu (Specialist) - Configuration submenu
Prog no. (on display)
Submenu parameter function Default setting Setup
5840 Solar control element Fill pumpFill pump or selector valve in relation to the type of solar heating system
5841 Outsidesolarheatexchanger BothConfigurebasedonrequirements
and system characteristics
Solar control element In place of the collector pump and selector valves, a solar heating system can be used as a supplementary heat source for the storage tanks, managing
the heat generation system fill pumps. If a selector valve is used, only one heat exchanger can be used at any one time. In this case, only alternating operation is allowed. If a fill pump is used, all the heat exchangers at the same time. In this case, both parallel and alternating operation are possible.
Outside solar heat exchanger For solar heating systems fitted with two storage tanks, the outside heat exchanger needs to be configured to be used for DHW and the buffer tank, or just
for one of the two.
- 99 -
B31
B3
Q5 Q16
B6 B61
Setup menu (Specialist) - Configuration submenu
Prog no. (on display)
Submenu parameter function Default setting Setup
5890, 5891, 5892, 5894 Relay output QX1,QX2, QX3, QX4 None Collector pump Q5
5890, 5891, 5892, 5894 Relay output QX1,QX2, QX3, QX4 None Collector pump 2 Q16
5930, 5931, 5932, 5933 Probe input BX1,BX2, BX3, BX4 None Collector probe B6
5930, 5931, 5932, 5933 Probe input BX1,BX2, BX3, BX4 None DHW probe B31
5930, 5931, 5932, 5933 Probe input BX1,BX2, BX3, BX4 None Collector probe 2 B61
N.B. QX1, QX2 and QX3 are 230 Vac outputs, while QX4 has voltage-free changeover contacts (the common is FX4).
B3
Q5
B31
B6
Setup menu (Specialist) - Configuration submenu
Prog no. (on display)
Submenu parameter function Default setting Setup
5890, 5891, 5892, 5894 Relay output QX1, QX2, QX3, QX4 None Collector pump Q5
5930, 5931, 5932, 5933 Probe input BX1, BX2, BX3, BX4 None Collector probe B6
5930, 5931, 5932, 5933 Probe input BX1, BX2, BX3, BX4 None DHW probe B31
N.B. QX1, QX2 and QX3 are 230 Vac outputs, while QX4 has voltage-free changeover contacts (the common is FX4).
GB
28.3 SUPPLEMENTARY SOLAR THERMAL WITH TWO COLLECTORS
28.2 SUPPLEMENTARY SOLAR THERMAL WITH ONE COLLECTOR AND SEPARATE BUFFER TANK
- 100 -
For information on programming and further details, see the complete
list of parameters and/or contact Ferroli technical service.
28.5 COLLECTOR FROST PROTECTION
When there is the risk of ice or frost on the solar collector, the collector pump is activated prevent the heat carrier fluid from freezing.
Specialist menu - Solar collector submenu
Prog no. (on display)
Submenu parameter function
3840 Collector frost protection
28.6 COLLECTOR OVERHEAT PROTECTION
When there is the risk of the collector overheating, the storage cylinder is filled with hot water (by activating the collector pump), so as to take away the
excessheat.Oncethesafetytemperatureisreachedinthestoragecylinder,thefillpumpstops.
Specialist menu - Solar collector submenu
For information on programming and further details, see the complete
list of parameters and/or contact Ferroli technical service.
Prog no. (on display)
Submenu parameter function
3850 Collector overheat protection
Note: TLmin refers to parameters 3812, 3815 (also 3818 “Minimum pool heating temperature”, not dealt with in this manual).
For information on programming and further details, see the complete
list of parameters and/or contact Ferroli technical service.
28.4 OVERVIEW OF SETTINGS FOR HEATING THE DHW STORAGE CYLINDER BY SUPPLEMENTARY SOLAR HEAT EXCHANGER
Heat controller (dT) To fill the domestic hot water storage cylinder with hot water from a heat exchanger, there needs to be a temperature differential between the collector and the storage cylinder, and the minimum heating temperature needs to be reached. Refer to the following list of parameters and diagrams to adapt system behaviourtospecificrequirements.
Prog no. (on display)
Submenu parameter function
3810 CollectorONtemperaturedifferential
3811 CollectorOFFtemperaturedifferential
3812 Minimum DHW storage cylinder heating temperature
3815 Minimum storage tank heating temperature
Specialist menu - Solar collector submenu
ON
OFF
SdOn
SdOff
TSp
TLmin
t
TTkol
ON
OFF
SDon
SDoff
BX
t
TTkx
KeyT Tkol Collector temperatureON/OFF Collector pumpSdOn ONtemperaturedifferentialSdOff OFFtemperaturedifferentialTSp Storage tank temperatureTLmin Minimum DHW/buffer/pool storage heating temperature
- 101 -
GB
29.1 OPERATING MODESpecialist menu - Solid fuel boiler submenu
Prog no. (on display)
Submenu parameter function Default setting Setup
4102 Deactivate other heat sources On On/Offaccordingtorequirements
Deactivate other heat sources When starting the solid fuel boiler, the other sources of heat, such as oil / gas-fired boilers, will be deactivated. These appliances are shut down as soon as the boiler temperature reaches a level that implies that the comparative temperature will soon be exceeded. This anticipatory function allows the deactivated heat sources to fully stop their pumps before the solid fuel boiler pump is activated. In addition, if these appliances share the same stack, it ensures that only one boiler is operating at any one time.
29.2 SET POINTSpecialist menu - Solid fuel boiler submenu
Prog no. (on display)
Submenu parameter function Default setting Setup
4110 Minimum set point 40°C Setbasedonrequirements
Minimum set point If parameter 4133 “Comparative temperature” (see the following table) is set as “Min set point”, the boiler pump Q10 will only be started when the solid
fuel boiler temperature has reached the minimum temperature level defined by this parameter, plus a set differential (parameters 4130 and 4131).
29.3 BOILER / BURNER CONTROLSpecialist menu - Solid fuel boiler submenu
Prog no. (on display)
Submenu parameter function Default setting Setup
4130 ONtempdifferential 8°C Setbasedonrequirements
4131 OFFtempdifferential 4°C Setbasedonrequirements
4133 Comparative temperature Setpoint minimoSetbasedonrequirementsand system characteristics
Differential controller (dT) For the boiler pump Q10 to be activated, there must be a sufficiently wide temperature differential between the boiler temperature and the comparative
temperature (this differential is defined by parameters 4130 and 4131).
ON
OFF
SdOn
SdOff
TSp
TLmin
t
TTkol
ON
OFF
SDon
SDoff
BX
t
TTkx
KeyT Tkx Boiler temperatureBx Effective comparative temperature valueON/OFF Boiler pumpSDon ONtemperaturedifferentialSDoff OFFtemperaturedifferential
29. SOLID FUEL BOILERThe list of parameters and specific instructions for correct integrated management of heat generation using a solid fuel boiler are enclosed.
For information on programming and further details, see the complete
list of parameters and/or contact Ferroli technical service.
Q10
B22 T
- 102 -
Prog no. (on display)
Reference menu
Submenu parameter function Default setting
RangeUnit of
measureMin Max
Time and date1 T Hour/minutes - 0:00 23:59 hh:mm
2 T Month, day - 01.01 31.12 dd.mm
3 T Year - 2004 2099 yyyy
5 S Start daylight saving 25.03 01.01 31.12 dd.mm
6 S End daylight saving 25.10 01.01 31.12 dd.mmControl UOM
20 TLanguageEN ¦ Deutsch - D ¦ FR ¦ IT ¦ NL ¦ ES ¦ PO ¦ DK ¦ SU ¦ S ¦
Deutsch(German) -
22 S InformationTemporary ¦ Permanent
Temporary -
26 S Lock controlsOff ¦ On
Off -
27 S Lock programmingOff ¦ On
Off -
28 M-S Direct controlSave automatically ¦ Save with confirmation
Save with confirmation -
29 M-S Control UOM°C, bar ¦ °F, PSI
°C, bar -
44 M-SOperation of CR2Together with CR1 ¦ Independent
Together with CR1 -
46 M-SOperation of CR3/PTogether with CR1 ¦ Independent
Together with CR1 -
70 S Software version 06.1 T 99.9 -
Radio (not used)
Time program CR 1
500 TOptionsMon-Sun ¦ Mon-Fri ¦ Sat-Sun ¦ Mon ¦ Tue ¦ Wed ¦ Thu ¦ Fry ¦ Sat ¦ Sun
Mon - Sun
501 T 1stOnperiod 6:00 00:00 24:00 hh:mm
502 T 1stOffperiod 22:00 00:00 24:00 hh:mm
503 T 2ndOnperiod --:-- 00:00 24:00 hh:mm
504 T 2ndOffperiod --:-- 00:00 24:00 hh:mm
505 T 3rdOnperiod --:-- 00:00 24:00 hh:mm
506 T 3rdOffperiod --:-- 00:00 24:00 hh:mm
516 T Standard valuesNo ¦ Yes
No
Time program CR 2520.....536
T (same time program as CR1)
30. VIEWING AND MANAGING PARAMETERS
The table describes:
- All the parameters (shown on the display with Prog. no.) in each Submenu;
- The Menu that each Submenu is part of (T=All; M=Setup (technical service); S=Specialist (installer));
- The function of each parameter, its default setting and range of possible values.
Note:Theparametersareshownonthedisplaywith“Prog.NOFF”andabbreviatedas“LP.+NOFF” (e.g. LP5770)
- 103 -
Prog no. (on display)
Reference menu
Submenu parameter function Default setting
RangeUnit of
measureMin Max
Time program 3/CRP540.....556
T (same time program as CR1)
Time program 4/DHW550.....576
T (same time program as CR1)
Time program 5600.....616
T (same time program as CR1)
Vacation CR 1
641 TOptionsPeriod 1 ¦ Period 2 ¦ Period 3 ¦ Period 4 ¦ Period 5 ¦ Period 6 ¦ Period 7 ¦ Period 8
Period 1
642 T Start --:-- 01.01 31.12 dd.mm
643 T End --:-- 01.01 31.12 dd.mm
648 T OperatinglevelFrost protection ¦ Reduced
Frost protection
Vacation CR 2651.....658
T (same time program as CR1)
Vacation CRP661.....668
T (same time program as CR1)
Central heating circuit 1710 T Comfort set point 20.0 LP716 LP716 °C
712 T Reduced set point 16 LP714 LP710 °C
714 T Frost protection set point 10.0 4 LP712 °C
716 S Max comfort set point 35.0 LP710 35 °C
720 T Characteristic curve slope 1.50 0.10 4.00 °C
721 S Curve offset 0.0 -4.5 4.5 °C
726 S Curve adaptation Off ¦ On
Off -
730 T Summer/winter changeover limit value 18 ---/8 30 °C
732 S Daytime heating limit value -3 ---/-10 10 °C
740 M-S Min outlet set point 8 8 LP741 °C
741 M-S Max outlet set point 80 LP740 95 °C
750 S Room temperature influence 20 ---/1 100 %
760 S Room temperature limitation 1 ---/0.5 4 °C
770 S Rapid heating 5 ---/0 20 °C
780 S Rapid reductionOff ¦ To reduced set point ¦ To frost protection set point
To reduced set point -
790 S Optimisationonstarting 0 0 360 min
791 S OptimisationonshutdownMax 0 0 360 min
800 S Start increase reduced set point --- ---/-3 10 °C
801 S End increase reduced set point -15 -30 LP800 °C
820 S Circuit protection pumpOff ¦ On
On -
GB
- 104 -
Prog no. (on display)
Reference menu
Submenu parameter function Default setting
RangeUnit of
measureMin Max
830 S Boost mixing valve 5 0 50 °C
832 S Type of actuator2-position¦ 3-position
3-position -
833 S 2-pos switching differential 2 0 20 °C
834 S Actuator travel time 120 30 873 s
850 T
Floor screed functionOff ¦ Functional heating ¦ Ready-to-lay heating ¦ Functional/ready-to-lay heating ¦ Ready-to-lay/functional heating ¦ Manual
Off -
851 T Manual screed set point 25 0 95 °C
861 S Dissipation of excess heatOff ¦ Central heating ¦ Always
Always -
870 S With storage cylinderNo ¦ Yes
Yes -
872 S With primary control/system pumpNo ¦ Yes
Yes -
882 S Pump speed - minimum 100 0 100 %
883 S Pump speed - maximum 100 0 100 %
900 S Change operating modeNone ¦ Protection ¦ Reduced ¦ Comfort ¦ Automatic
Protection mode -
Central heating circuit 21010 T Comfort set point 20.0 LP716 LP716 °C
1012 T Reduced set point 16 LP714 LP710 °C
1014 T Frost protection set point 10.0 4 LP712 °C
1016 S Max comfort set point 35.0 LP710 35 °C
1020 T Characteristic curve slope 1.50 0.10 4.00 °C
1021 S Curve offset 0.0 -4.5 4.5 °C
1026 S Curve adaptation Off ¦ On
Off -
1030 T Summer/winter changeover limit value 18 ---/8 30 °C
1032 S Daytime heating limit value -3 ---/-10 10 °C
1040 M-S Min outlet set point 8 8 LP741 °C
1041 M-S Max outlet set point 80 NP740 95 °C
1050 S Room temperature influence 20 ---/1 100 %
1060 S Room temperature limitation 1 ---/0.5 4 °C
1070 S Rapid heating 5 ---/0 20 °C
1080 S Rapid reductionOff ¦ To reduced set point ¦ To frost protection set point
To reduced set point -
1090 S Optimisationonstarting 0 0 360 min
1091 S OptimisationonshutdownMax 0 0 360 min
1100 S Start increase reduced set point --- ---/-3 10 °C
1101 S End increase reduced set point -15 -30 LP800 °C
1120 S Circuit protection pumpOff ¦ On
On -
1130 S Comparative set point positive differential 5 0 50 °C
1132 S Type of actuator2-position ¦ 3-position
3-position -
1133 S Switching differential 2 2 0 20 °C
1134 S Actuator travel time 120 30 873 s
1150 M-S
Floor screed functionOff ¦ Functional heating ¦ Ready-to-lay heating ¦ Functional/ready-to-lay heating ¦ Ready-to-lay/functional heating ¦ Manual
Off -
- 105 -
Prog no. (on display)
Reference menu
Submenu parameter function Default setting
RangeUnit of
measureMin Max
1151 M-S Manual screed set point 25 0 95 °C
1161 S Dissipation of excess heatOff ¦ Central heating ¦ Always
Always -
1170 S With storage cylinderNo ¦ Yes
Yes -
1172 S With primary control/system pumpNo ¦ Yes
Yes -
1182 S Pump speed - minimum 100 0 100 %
1183 S Pump speed - maximum 100 0 100 %
1200 S Change operating modeNo ¦ Protection ¦ Reduced ¦ Comfort ¦ Automatic
Protection mode -
Central heating circuit CRP
1300 T OperatingmodeProtection ¦ Automatic ¦ Reduced ¦ Comfort
Automatic mode -
1310 T Comfort set point 20.0 LP716 LP716 °C
1312 T Reduced set point 16 LP714 LP710 °C
1314 T Frost protection set point 10.0 4 LP712 °C
1316 S Max comfort set point 35.0 LP710 35 °C
1320 T Characteristic curve slope 1.50 0.10 4.00 °C
1321 S Curve offset 0.0 -4.5 4.5 °C
1326 S Curve adaptation Off ¦ On
Off -
1330 T Summer/winter changeover limit 18 ---/8 30 °C
1332 M-S 24 hour heating limit -3 ---/-10 10 °C
1340 M-S Min outlet temperature set point 8 8 LP741 °C
1341 M-S Max outlet temperature set point 80 NP740 95 °C
1350 S Room temperature influence 20 ---/1 100 %
1360 S Room temperature limitation 1 ---/0.5 4 °C
1370 S Rapid heating 5 ---/0 20 °C
1380 S Rapid reductionOff ¦ To reduced set point ¦ To frost protection set point
To reduced set point -
1390 S Optimisationonstarting 0 0 360 min
1391 S Optimisationonshutdown 0 0 360 min
1400 S Start increase reduced set point --- ---/-3 10 °C
1401 S End increase reduced set point -15 -30 LP800 °C
1420 S Circuit anti-overheat pumpOff ¦ On
On -
1450 M-SFloor screed functionOff ¦ Functional heating ¦ Ready-to-lay heating ¦ Functio-nal/ready-to-lay heating ¦ Manual
Off -
1451 M-S Manual screed set point 25 0 95 °C
1455 ICurrent screed set pointCurrent screed day
0 0 95 °C
1461 S Dissipation of excess heatOff ¦ Central heating mode ¦ Always
Always -
1470 S With storage cylinderNo ¦ Yes
Yes -
1472 S Con regolatore primario/pompa di sistemaNo ¦ Yes
Yes -
1482 S Pump speed - minimum 100 0 100 %
1483 S Pump speed - maximum 100 0 100 %
1500 S Change operating modeNone ¦ Protection ¦ Reduced ¦ Comfort ¦ Automatic
Protection mode -
GB
- 106 -
DHW
1610 T Standard set point 55 LP 1612LP 1614
OEM°C
1612 S Reduced set point 40 8 LP 1610 °C
1620 S EnablingTime program 4/CR ¦ Time program CR ¦ 24 hours/day
Time program CR
1630 M-SHeating priority Absolute ¦ Compensation ¦ None ¦ Mixed circuit compensation/direct circuit absolute
Mixed circuit compensa-tion/direct circuit absolute
-
1640 S Legionella protection functionOff ¦ Periodical ¦ Fixed weekday
Fixed weekday -
1641 S Legionella protection function 3 1 7 Day
1642 SDaily legionella protection function Monday ¦ Tuesday ¦ Wednesday ¦ Friday ¦ Saturday ¦ Sunday
Monday
1644 S Legionella protection function time --- ---/ 00:00 23:50 hh:mm
1645 S Legionella protection function set point 65 55 95 °C
1646 S Legionella protection function duration 30 ---/10 360 min
1647 S Legionella protection function circulating pumpOff ¦ On
On -
1660 SEnable recirculation pumpTime program 3/CRP ¦ Enabled by DHW ¦ Time program 4/DHW
Enabled by DHW -
1661 S Circulating pump duty cycleOff ¦ On
On -
1663 S Recirculation set point 45 8 80 °C
Pump Hx
2010 S H1 dissipation of excess heatOff ¦ On
On -
2012 S H1 with storageNo ¦ Yes
Yes -
2014 S H1 primary control/system pumpNo ¦ Yes
Yes -
2035 S H2 dissipation of excess heatOff ¦ On
On -
2037 S H2 with storageNo ¦ Yes
Yes -
2039 S H2 primary control/system pumpNo ¦ Yes
Yes -
2046 S H3 dissipation of excess heatOff ¦ On
On
2048 S H3 with storageNo ¦ Yes
Yes
2050 S H3 primary control/system pumpNo ¦ Yes
Yes
Pool2055 T Solar heating set point 26 8 80 °C
2056 T Non-solarsourceheatingsetpoint 22 8 80 °C
2065 S Priority of solar heatingNo ¦ Yes
No
2080 S With solar connectionNo ¦ Yes
Yes
System primary control
2150 T Primary control/system pumpBefore storage ¦ buffer tank ¦ After
After storage -
Prog no. (on display)
Reference menu
Submenu parameter function Default setting
RangeUnit of
measureMin Max
- 107 -
Boiler2203 S Enable below out. temp. --- ---/-50 50 °C
2205 S With eco modeOff ¦ DHW on ¦ On
Off
2208 S Completely heat storage cylinderOff ¦ On
Off
2210 S Minimum set point 40LP 2211
OEM
Manual set
point°C
2212 S Maximum set point 80Manual
setpoint
LP 2213OEM
°C
2270 S Minimum return set point 8 8 95 °C
2330 S Nominaloutput 50 0 1000 kW
2331 S Main stage output 30 0 1000 kW
2340 S2x1cascadeautosequenceBoilerchangeoverfrequencyin2x1cascade
500 ---/10 990 h
Heat generators in cascade3532 S Disable restart 300 0 1800 s
3533 S Delay on starting 5 0 120 min
3540 S Automaticsourcesequence 500 ---/10 990 h
3541 S Excludesourcefromautomaticsequencenone ¦ first ¦ last ¦ first and last
None
3544 S Main sourceSource 1 ¦ Source 2 ¦ ... ¦ Source 16
Source 1
3560 S Minimum return temperature set point 8 8 95 °C
Solar collector3810 S CollectorONtemperaturedifferential 8 0 40 °C
3811 S CollectorOFFtemperaturedifferential 4 0 40 °C
3812 S Minimum DHW storage cylinder heating temperature --- ---/8 95 °C
3815 S Minimum storage tank heating temperature --- ---/8 95 °C
3818 S Minimum pool heating temperature --- ---/8 95 °C
3822 S Solar heating priority settingnone ¦ DHW storage cylinder ¦ storage tank
DHW storage cylinder
3825 S Priority circuit heating time --- ---/2 60 min
3826 S Priority circuit waiting time 5 1 40 min
3827 S Parallel operation waiting time --- ---/0 40 min
3828 S Secondary pump activation delay time 60 0 600 s
3831 S Minimum collector pump running time 20 5 120 s
3834 S Gradientfunctiontostartcollectorpump --- ---/1 20 min/ °C
3840 S Collector frost protection --- ---/-20 5 °C
3850 S Collector overheat protection --- ---/30 350 °C
3860 S Heat carrier fluid evaporator --- ---/60 350 °C
3870 S Minimum pump speed 40 0 100 %
3871 S Maximum pump speed 100 0 100 %
3880 S Type of antifreeze-glycolnone ¦ ethylene ¦ polyethylene ¦ ethylene and polyethylene
None
3881 S Antifreeze concentration 30 1 100 %
3884 S Pump flow-rate 200 0 1500 l/h
Prog no. (on display)
Reference menu
Submenu parameter function Default setting
RangeUnit of
measureMin Max
GB
- 108 -
Solid fuel boiler
4102 S Deactivate other heat sourcesOff ¦ On
On -
4110 S Minimum set point 40 8 120 °C
4130 S ONtempdifferential 8 1 40 °C
4131 S OFFtempdifferential 4 0 40 °C
4133 SComparative temperatureB3 DHW sensor ¦ B31 DHW sensor ¦ B4 sensor storage ¦ B41 storage sensor ¦ flow temp set point ¦ min. set point
Minimum set point
Buffer storage tank
4720 S Heat generation auto offNone ¦ With B4 ¦ With B4 and B42/41
with B4
4722 S Central heating circuit storage temperature diff. -5 -20 20 °C
4724 S Minimum tank temperature in heating mode --- ---/8 95 °C
4750 S Maximum heating temperature 80 8 95 °C
4755 S Cooling temperature 60 8 95 °C
4756 S DHW cooling/central heating circuit Off ¦ On
Off -
4757 S Cooling by circulation in collectorsOff ¦ Summer ¦ Always
Off
4783 S With supplementary solarNo ¦ Yes
No
4790 S ONtemperaturedifffordeviationtoreturn 10 0 40 °C
4791 S OFFtemperaturedifffordeviationtoreturn 5 0 40 °C
4795 S Comparative temperature on return deviationB4 ¦ B41 ¦ B42
B42
4796 S Return deviation optionIncrease in temp. ¦ Reduction in temp.
Increase in temperature
4800 S Partial heating set point --- ---/8 95 °C
DHW storage5020 S Increase outlet set point 16 0 30 °C
5021 S Boost transfer 8 0 30 °C
5022 S Type of heating with B3 ¦ with B3/B31 ¦ with B3, legion B3/B31
with B3/B31 -
5050 S Maximum heating temperature 80 8LP 5051
OEM°C
5055 S Cooling temp. 80 8 95 °C
5056 S Boiler cooling / CHOff ¦ On
Off -
5057 S Collector coolingOff ¦ Summer ¦ Always
Off -
5060 S Electric heater modeReplacement ¦ Summer ¦ Always
Replacement -
5061 SElectric heater operation24 hours/day ¦ Enabled by DHW ¦ Time program 4/DHW
Enabled by DHW -
5062 S Electric heater controlExternal thermostat ¦ DHW sensor
DHW sensor -
5085 S Dissipation of excess heatOff ¦ On
On -
5090 S With storage cylinderNo ¦ Yes
No -
5092 S With primary control/system pumpNo ¦ Yes
No -
5093 S With supplementary solarNo ¦ Yes
Yes -
5101 S Minimum pump speed 40 0 100 %
5102 S Maximum pump speed 100 0 100 %
Prog no. (on display)
Reference menu
Submenu parameter function Default setting
RangeUnit of
measureMin Max
- 109 -
Instant DHW heater5406 S Minimum set point differential 4 0 20 °C
5544 S Actuator opening time 60 7.5 480 s
Configuration
5710 M-S Central heating circuit 1Off ¦ On
On -
5715 M-S Central heating circuit 2Off ¦ On
Off -
5730 M-S DHW sensor B3Probe ¦ Thermostat
Probe -
5731 M-S DHW actuator Q3No heat demand ¦ Fill pump ¦ Selector valve
Fill pump -
5736 M-S Separate DHW circuitOff ¦ On
Off -
5770 M-SType of heat generator1 stage ¦ 2 stage ¦ 3-position mod. ¦ Modulating UX ¦ Without boiler probe ¦ 2 x 1 cascade
2 stage -
5840 M-S Solar control elementFill pump ¦ Selector valve
Fill pump -
5841 M-S OutsidesolarheatexchangerBoth ¦ DHW storage ¦ Buffer
Both -
5890 M-S
Relay output QX1None ¦ Recirculating pump Q4 ¦ DHW electric heater K6 ¦ Collector pump Q5 ¦ Pump H1 Q15 ¦ Boiler pump Q1 ¦ Bypass pump Q12 ¦ Alarm output K10 ¦ CR1 pump speed Q21 ¦ CR2 pump speed Q22 ¦ Pump speed CRP Q23 ¦ CRP pump Q20 ¦ Pump H2 Q18 ¦ System pump Q14 ¦ Selector valve Y4 ¦ Wood-fired boiler pump Q10 ¦ Time program 5 K13 ¦ Buffer return valve Y15 ¦ External heat solar heat exchanger pump K9 ¦ Storage cylinder solar control elem. K8 ¦ Pool solar control elem. K18 ¦ Collec-tor pump 2 Q16 ¦ H3 pump Q19 ¦ Flue gas relay K17 ¦ Assist. comb. fan K30 ¦ Cascade pump Q25 ¦ Storage cylinder trans. pump Q11 ¦ DHW mix pump Q35 ¦ DHW inter. pump Q33 ¦ Heat demand K27
None -
5891 M-S Relay output QX2(as for “relay output QX1”)
None
5892 M-S Relay output QX3(as for “relay output QX1”)
None
5894 M-S Relay output QX4(as for “relay output QX1”)
None
5930 M-S
Probe input BX1None ¦ DHW probe B31 ¦ Collector probe B6 ¦ Return probe B7 ¦ DHW circulation probe B39 ¦ Buffer probe B4 ¦ Buffer probe B41 ¦ Flue gas temp. probe B8 ¦ Common outlet probe B10 ¦ Wood-fired boiler probe B22 ¦ DHW probe fill B36 ¦ Buffer probe B42 ¦ Common return pro-be B73 ¦ Cascade return probe B70 ¦ Pool probe B13 ¦ Collector probe 2 B61 ¦ Solar outlet probe B63 ¦ Solar return probe B64
None -
5931 M-S Probe input BX2(as for “probe input BX1”)
None
5932 M-S Probe input BX3(as for “probe input BX1”)
None
5933 M-S Probe input BX4(as for “probe input BX1”)
None
Prog no. (on display)
Reference menu
Submenu parameter function Default setting
RangeUnit of
measureMin Max
GB
- 110 -
5950 M-S
Input H1 functionChange operating mode CH+DHW ¦ Change operating mode CH ¦ Change operating mode CR1 ¦ Change ope-rating mode CR2 ¦ Change operating mode CRP ¦ Stop heat production ¦ Error/alarm message ¦ Minimum outlet set point ¦ Dissipation of excess heat ¦ Enable pool ¦ 10V heat demand ¦ 10V pressure measurement
Change operating mode CH+DHW
5951 M-S Contact H1 logicNormally closed ¦ Normally open
Normallyopen -
5952 M-S Minimum outlet set point 70 8 120 °C
5954 M-S Temperature value 10V H1 100 5 130 °C
5956 M-S Pressure value 3.5V H1 5.0 0.0 10.0 bar
5960 M-S
Input H3 functionChange operating mode CH+DHW ¦ Change operating mode CH ¦ Change operating mode CR1 ¦ Change ope-rating mode CR2 ¦ Change operating mode CRP ¦ Stop heat production ¦ Error/alarm message ¦ Minimum outlet set point ¦ Dissipation of excess heat ¦ Enable pool ¦ 10V heat demand ¦ 10V pressure measurement
Change operating mode CH+DHW
-
5961 M-S Contact H3 logicNormally closed ¦ Normally open
Normallyopen -
5962 M-S Minimum outlet set point H3 70 8 120 °C
5964 M-S Temperature value 10V H3 100 5 130 °C
5966 M-S Pressure value 3.5V H3 5.0 0.0 10.0 bar
5982 M-S
Input EX2 functionBurner stage 2 hour counter ¦ Stop heat production ¦ Error/alarm message ¦ SLT error message ¦ Dissipation of excess heat
Burner stage 2 hour counter
-
5983 M-S Input EX2 logicNormally closed ¦ Normally open
Normallyopen
6014 M-S
Mix1 unit functionCentral heating circuit 1 ¦ Return temp. cont. ¦ Prim cont./system pump ¦ DHW heat cont. ¦ Instant DHW ¦ Cascade return control
Central heating circuit 1
6015 M-S
Mix2 unit functionCentral heating circuit 2 ¦ Return temp. cont. ¦ Prim cont./system pump ¦ DHW heat cont. ¦ Instant DHW ¦ Cascade return control
Central heating circuit 2
6020 M-S
Expansion module 1 functionNone ¦ Multi-function ¦ Central heating circuit 2 ¦ Return temp. control ¦ Solar DHW ¦ Prim. cont./ sys. pump ¦ DHW heat cont. ¦ Instant DHW ¦ Cascade return control
None -
6021 M-S
Expansion module 2 functionNone ¦ Multi-function ¦ Central heating circuit 2 ¦ Return temp. control ¦ Solar DHW ¦ Prim. cont./ sys. pump ¦ DHW heat cont. ¦ Instant DHW ¦ Cascade return control
None -
6030 M-S
Relay QX21None ¦ Recirculating pump Q4 ¦ DHW electric heater K6 ¦ Collector pump Q5 ¦ Pump H1 Q15 ¦ Boiler pump Q1 ¦ Bypass pump Q12 ¦ Alarm output K10 ¦ CR1 pump speed Q21 ¦ CR2 pump speed Q22 ¦ Pump speed CRP Q23 ¦ CRP pump Q20 ¦ Pump H2 Q18 ¦ System pump Q14 ¦ Selector valve Y4 ¦ Wood-fired boiler pump Q10 ¦ Time program 5 K13 ¦ Buffer return valve Y15 ¦ External heat solar heat exchanger pump K9 ¦ Storage cylinder solar control elem. K8 ¦ Pool solar control elem. K18 ¦ Collector pump 2 Q16 ¦ Pump H3 Q19 ¦ Flue gas relay K17 ¦ Assist. comb. fan K30 ¦ Cascade pump Q25 ¦ Storage cylinder trans. pump Q11 ¦ DHW mix pump Q35 ¦ DHW inter. pump Q33 ¦ Heat demand K27
None
6031 M-S Relay output QX22(as for “Relay QX21”)
None
Prog no. (on display)
Reference menu
Submenu parameter function Default setting
RangeUnit of
measureMin Max
- 111 -
6032 M-S M-S Relay output QX23(as for “Relay QX21”)
none
6040 M-S
Probe input BX21None ¦ DHW probe B31 ¦ Collector probe B6 ¦ Return probe B7 ¦ DHW circulation probe B39 ¦ Buffer probe B4 ¦ Buffer probe B41 ¦ Flue gas temp. probe B8 ¦ Common outlet probe B10 ¦ Wood-fired boiler probe B22 ¦ DHW probe fill B36 ¦ Buffer probe B42 ¦ Common return probe B73 ¦ Cascade return probe B70 ¦ Pool probe B13 ¦ Collector probe 2 B61 ¦ Solar outlet probe B63 ¦ Solar return probe B64
none
6041 M-S Probe input BX22(as for “probe input BX21”)
none
6046 M-S
Input H2 functionChange operating mode CH+DHW ¦ Change operating mode CH ¦ Change operating mode CR1 ¦ Change ope-rating mode CR2 ¦ Change operating mode CRP ¦ Stop heat production ¦ Error/alarm message ¦ Minimum outlet set point ¦ Dissipation of excess heat ¦ Enable pool ¦ 10V heat demand ¦ 10V pressure measurement
Change operating mode CH+DHW
6047 M-S Contact H2 logicNormally closed ¦ Normally open
Normallyopen
6048 M-S Minimum outlet set point H2 70 8 120 °C
6050 M-S Temperature value 10V H2 100 5 130 °C
6052 M-S Pressure value 3.5V H2 5.0 0.0 10.0 bar
6070 M-S
OutputUXfunctionNone ¦ Boiler pump Q1 ¦ DHW pump Q3 ¦ DHW inter. pump Q33 ¦ Pump CH circ. 1 Q2 ¦ CR2 pump Q6 ¦ CRP pump Q20 ¦ Collector pump Q5 ¦ Ext. solar heat exch. pump K9 ¦ Sol. storage cylinder pump K8 ¦ Sol. pool pump K18 ¦ Collector pump 2 Q16 ¦ Boiler set point ¦ Output set point ¦ Heat demand
None
6071 M-S OutputUXlogicstandard ¦ reverse
Standard
6075 M-S Temperature value 10V UX 100 5 130 °C
6097 S Type of collector temp probeNTC ¦ Platinum 100
NTC -
6098 S Collector probe correction 0 -20 20 °C
6099 S Collector sensor 2 correction 0 -20 20 °C
6100 S Outsideprobecorrection 0.0 -3.0 3.0 °C
6101 S Type of flue gas temperature probeNTC ¦ PT 100
NTC -
6102 S Flue gas temperature probe correction 0 -20 20 °C
6110 S Constant of time building 15 0 50 h
6120 S Frost protection systemOff ¦ On
Off -
6128 S Heat demand below summer temperature -- ---/-50 50 °C
6129 S Heat demand above summer temperature -- ---/-50 50 °C
6131 S Heat demand in eco modeOff ¦ DHW On ¦ On
Off
6200 M-S Save probeNo ¦ Yes
No -
6205 S Restore parameters (default)No ¦ Yes
No -
6212 M-S Generator1checkno. - 0 199999 -
6213 M-S Generator2checkno. - 0 199999 -
6215 M-S Storage cylinder check no. - 0 199999 -
Prog no. (on display)
Reference menu
Submenu parameter function Default setting
RangeUnit of
measureMin Max
GB
- 112 -
6217 M-S CH circuit check no. - 0 199999 -
6220 S Software version - 0 99.9 -
LPB6600 M-S Appliance address 1 0 16 -
6601 S Segment address 0 0 14 -
6604 S Bus power supply functionOff ¦ Automatic
Automatic -
6605 S Bus power supply statusOff ¦ On
On -
6620 S Changeover actionSegment ¦ System
System -
6621 S Summer changeoverLocally ¦ Central
Locally -
6623 S Change operating modeLocally ¦ Central
Central
6624 S Manual generator shutdownLocally ¦ Central
Locally
6625 SDomestic hot water assignmentAll local CH circ. ¦ All CH circ. in the segment | All CH circ. in the system
All the central heating circuits in the system
-
6631 S Ext. source in Eco modeOff ¦ DHW ON ¦ On
Off
6640 M-SClock modeIndependent ¦ Slave without remote set ¦ Slave with remote set ¦ Independent master
Independent -
6650 S Outsidetemperatureacquisition 0 0 239 -
Fault
6710 M-S Reset alarm relayNo ¦ Yes
No
6740 S Outlettemp.alarm1 --- ---/10 240 min
6741 S Outlettemp.alarm2 --- ---/10 240 min
6743 S Boiler temp. alarm --- ---/10 240 min
6745 S DHW heat alarm ---- ---/10 48 h
6800 S History 1Error code 1
- 0 255 -
6802 S History 2Error code 2
- 0 255 -
6804 S History 3Error code 3
- 0 255 -
6806 S History 4Error code 4
- 0 255 -
6808 S History 5Error code 5
- 0 255255 -
6810 S History 6Error code 6
- 0 255 -
6812 S History 7Error code 7
- 0 255 -
6814 S History 8Error code 8
- 0 255 -
6816 S History 9Error code 9
- 0 255 -
6818 S History 10Error code 10
- 0 255 -
Maintenance/Service function7040 S Burner operating hour interval --- ---/10 10000 h
7041 S Burner operating hours after maintenance 0 0 10000 h
7042 S Burner start interval --- ---/60 65535 -
7043 S Burner starts after maintenance 0 0 65535 -
7044 S Maintenance interval --- ---/1 240 months
7045 S Time elapsed since maintenance 0 0 240 months
Prog no. (on display)
Reference menu
Submenu parameter function Default setting
RangeUnit of
measureMin Max
- 113 -
7053 S Flue gas temperature limit --- ---/0 350 °C
7054 S Flue gas temperature alarm delay 0 0 120 min
7119 S ECOfunctionDisabled ¦ Enabled
Disabled
7120 T ECOmodeOff ¦ On
Off
7130 T Chimney sweep functionOff ¦ On
Off -
7140 T Manual operationOff ¦ On
Off -
7150 M-S Outsidetemperaturesimulation - -50.0 50 °C
7170 M-S Customer service telephone - -
Input/output test
7700 M-S
Relay testNo test ¦ All off ¦ Burner stage 1 T2 ¦ Burner stage 1-2 T2/QX4 ¦ DHW pump Q3 ¦ CH pump Q2 ¦ CH mixer open Y1 ¦ CH mixer closed Y2 ¦ CH pump Q6 ¦ CH mixer open Y5 ¦ CH mixer closed Y6 ¦ Relay output QX1 ¦ Relay output QX2 ¦ Relay output QX 3 ¦ Relay output QX4 ¦ Relay output QX21 module 1 ¦ Relay output QX22 module 1 ¦ Relay output QX23 module 1 ¦ Relay output QX21 module 2 ¦ Relay output QX22 module 2 ¦ Relay output QX23 module 2
Notest -
7710 M-S UX output test - 0 100 5
7711 M-S UX voltage values 0 0 10 Volt
7730 M-S OutsidetemperatureB9 - -50.0 50 °C
7732 M-S OutlettemperatureB1 - 0.0 140 °C
7734 M-S OutlettemperatureB12 - 0.0 140 °C
7750 M-S DHW temperature B3 - 0.0 140 °C
7760 M-S Boiler temperature B2 - 0.0 140 °C
7820 M-S Temperature probe BX1 - -28.00 350 °C
7821 M-S Temperature probe BX2 - -28.00 350 °C
7822 M-S Temperature probe BX3 0 -28 350 °C
7823 M-S Temperature probe BX4 0 -28 350 °C
7830 M-S Temperature probe BX21 module 1 0 -28 350 °C
7831 M-S Temperature probe BX22 module 1 0 -28 3,50 °C
7832 M-S Temperature probe BX21 module 12 0 -28 350 °C
7833 M-S Temperature probe BX22 module 2 0 -28 350 °C
7840 M-S Voltage signal H1 - 0 10 Volt
7841 M-S Contact H1 statusOpen ¦ Closed
Open -
7845 M-S Voltage signal H2 0 0 10 °C
7846 M-S Contact H2 statusOpen ¦ Closed
Open -
7854 M-S Voltage signal H3 0 0 10 Volt
7855 M-S Contact H3 statusOpen ¦ Closed
Open
7870 M-S Burner fault S30V ¦ 230V
0 V -
7881 M-S Burner stage 1 E10V ¦ 230V
0 V -
7912 M-S Input_ EX20V ¦ 230V
0 V -
Status8000 M-S Central heating circuit 1 status - -
8001 M-S Central heating circuit 2 status - -
8002 M-S Central heating circuit P status - -
Prog no. (on display)
Reference menu
Submenu parameter function Default setting
RangeUnit of
measureMin Max
GB
- 114 -
8003 M-S DHW status - -
8005 M-S Boiler status - -
8007 M-S Solar status - -
8008 M-S Wood-fired boiler status - -
8010 M-S Buffer status - -
8011 M-S Pool status - -
Heat generation diagnostics8100 to 8013
M-S Generation1to16priority
8101 to 8131
M-S
Generator1to16statusNot available ¦ In heating mode ¦ Manual control active ¦ Stop production active ¦ Chimney sweep function active ¦ DHW changeover active ¦ Outside temperature limitation active ¦ No activation ¦ Active
8138 M-S Cascade boiler outlet temperature 0 0 140 °C
8139 M-S Cascade boiler outlet set point 0 0 140 °C
8140 M-S Cascade boiler return temperature 0 0 140 °C
8141 M-S Cascade boiler return set point 0 0 140 °C
8150 M-S Current production changeover 0 0 990 h
Diagnostic parameters
8300 M-S Burner stage 1 T2Off ¦ On
On -
8301 M-S Burner stage 2Off ¦ On
On -
8308 S Boiler pump speed 0 0 100 %
8310 M-S Boiler temperatureBoiler set point
- 0.0 140.0 °C
8312 T Boiler changeover point 0 0 140 °C
8314 T Boiler return temperature - 0.0 140.0 °C
8316 M-S Flue gas temperature 0 0 350 °C
8318 M-S Max flue gas temperature 0 0 350 °C
8326 M-S Burner modulation 0 0 100 %
8330 S Stage 1 operating hours 0 0 65535 h
8331 S No.ofstartsstage1 - 0 199999 -
8332 S Stage 2 operating hours 0 0 65535 h
8333 S No.ofstartsstage2 0 0 199999 -
8505 S Collector pump 1 speed 0 0 100 %
8506 S Outsidesolarheatexchangerpumpspeed 0 0 100 %
8507 S Solar buffer pump speed 0 0 100 %
8508 S Solar pool pump speed 0 0 100 %
8510 M-S Collector 1 temperature - -28.0 350 °C
8511 M-S Collector 1 max temperature 0 -28.0 350 °C
8512 M-S Collector 1 min temperature 0 -28.0 350 °C
8513 M-S ∆T collector 1/DHW - -168.0 350 °C
8514 M-S ∆T collector 1/storage cylinder - -168.0 350 °C
8515 M-S ∆T collector 1/pool - -168.0 350 °C
8519 M-S Solar outlet temperature 0 -28.0 350 °C
8520 M-S Solar return temperature 0 -28.0 350 °C
8526 T Solar energy delivered in 24 hours 0 0 999.9 kW
8527 T Total solar energy delivered 0 0 9999999.9
8530 M-S Solar production operating hours - 0 65535
Prog no. (on display)
Reference menu
Submenu parameter function Default setting
RangeUnit of
measureMin Max
- 115 -
8531 S Collector overheat operating hours - 0 65535 h
8543 S Collector 2 pump speed 0 0 100 %
8547 M-S Collector 2 temperature 0 -28.0 350 °C
8548 M-S Collector 2 max temperature -28.0 -28.0 350 °C
8549 M-S Collector 2 min temperature 3500 -28 350 °C
8550 M-S ∆T collector 2/DHW 0 -168 350 °C
8551 M-S ∆T collector 2/buffer 0 -168 350 °C
8552 M-S ∆T collector 2/pool 0 -168 350 °C
8560 M-S Wood-fired boiler temperature 0 0 140 °C
8570 M-S Wood-fired boiler operating hours 0 0 65535 h
Input/output test8700 M-S Outsidetemperature - -50.0 50.0 °C
8703 M-S Attenuated outside temperature - -50.0 50.0 °C
8704 M-S Compound outside temperature - -50.0 50.0 °C
8730 M-S CH Pump QROff ¦ On
Off -
8731 M-S CH mixing valve open Y1Off ¦ On
Off -
8732 M-S CH mixing valve closed Y2Off ¦ On
Off -
8735 S CR1 pump speed 0 0 100 %
8740 M-S Room temperature 1 --
4.050
35.0°C
8743 M-S Outlettemperature1 - 0.0 140.0 °C
8760 M-S CR2 pumpOff ¦ On
Off -
8761 M-S CH mixing valve 2 openOff ¦ On
Off -
8762 M-S CH mixing valve 2 closedOff ¦ On
Off -
8765 M-S CR2 pump speed 0 0 100 %
8770 M-S Room temperature 2 --
4.050
35.0°C
8773 M-S Outlettemperature2 - 0.0 140.0 °C
8795 M-S CRP pump speed 0 0 100 %
8800 M-S Room temperature P --
4.050
35.0°C
8803 M-S OutletsetpointP - 0.0 140.0 °C
8820 M-S DHW pump Q3Off ¦ On
Off -
8825 S DHW pump speed 0 0 100 %
8826 S DHW intermediate circ. pump speed 0 0 100 %
8830 M-S DHW temperature 1 -0.08.0
140.080.0
°C
8832 M-S DHW temperature 2 - 0.0 140.0 °C
8835 M-S DHW circulation temperature - 0.0 140.0 °C
8836 M-S DHW heat temperature 0 0 140 °C
8850 M-S DHW temperature primary controlPrimary control set point
0 0 140 °C
8852 M-S DHW delivery set point 0 0 140 °C
8900 M-S Pool temperature0
2408
14080
°C
8930 M-S Primary control temp. - 0.0 140.0 °C
Prog no. (on display)
Reference menu
Submenu parameter function Default setting
RangeUnit of
measureMin Max
GB
- 116 -
8950 M-S Common outlet temperatureCommon outlet set point
- 0.0 140-0 °C
8952 M-S Common return temperature 0 0 140 °C
8962 M-S Common output set point 0 0 100 °C
8980 M-S Buffer temperature 1 - 0.0 140-0 °C
8981 M-S Buffer set point 0 0 140 °C
8982 M-S Buffer temperature 2 - 0.0 140.0 °C
8983 M-S Buffer temperature 3 0 0 140 °C
9000 M-S OutletsetpointH1 - 5.0 130.0 °C
9001 M-S OutletsetpointH2 - 5.0 130.0 °C
9004 M-S OutletsetpointH3 8 8 120 °C
9005 M-S Water pressure H1 - 0.0 10.0 bar
9006 M-S Water pressure H2 - 0.0 10.0 bar
9009 M-S Water pressure H3 - 0 10.0 bar
9031 Relay output QX1Off ¦ On
Off -
9032 Relay output QX2Off ¦ On
Off -
9033 M-S Relay output QX3Off ¦ On
Off -
9034 M-S Relay output QX4Off ¦ On
Off -
9050 M-S Relay output QX21 module 1Off ¦ On
Off -
9051 M-S Relay output QX22 module 1Off ¦ On
Off -
9052 M-S Relay output QX23 module 1Off ¦ On
Off -
9053 M-S Relay output QX21 module 2Off ¦ On
Off -
9054 M-S Relay output QX22 module 2Off ¦ On
Off -
9055 M-S Relay output QX23 module 2Off ¦ On
Off -
Prog no. (on display)
Reference menu
Submenu parameter function Default setting
RangeUnit of
measureMin Max
- 117 -
GB
The “bell” symbol on the display indicates that an error/fault has occurred; to view the cause, press
31. ERROR/FAULT CODES
Error code Description0 Noerror
10 Outsidetemperatureprobe
20 Boiler temperature probe 1
25 Solid fuel boiler temperature probe
26 Common flow temperature probe
28 Flue gas temperature probe
30 Flow temperature probe 1
32 Outletprobe2
38 Outlettemperatureprimarycontrol
40 Return temperature probe 1
46 Cascade return temperature probe
47 Common temperature probe
50 Domestic hot water probe 1
52 Domestic hot water probe 2
54 DHW primary control probe
57 DHW circulation temperature probe
70 Buffer tank probe 1
71 Buffer tank probe 2
72 Buffer tank probe 3
73 Collector probe 1
74 Collector probe 2
81 LPB short-circuit/comm
82 LPB address conflict
83 BSB short-circuit
84 BSB address conflict
100 Main time (LPB)
102 Main clock without backup (LPB)
105 Maintenance message
109 Boiler temperature supervision
110 Boiler thermostat shutdown
117 Water pressure too high
118 Water pressure too low (critical limit)
121 Outlettemperature1supervision(HC1)
122 Outlettemperature2supervision(HC2)
126 Domestic hot water heat control
127 Legionella function temperature not reached
131 Burner fault
146 Common error message configuration
171 Alarm contact 1 active
172 Alarm contact 2 active
173 Alarm contact 3 active (EX2/230VAC)
174 Alarm contact 4 active (H3)
176 Water pressure 2 too high
177 Water pressure 2 too low (critical limit)
178 Central heating circuit 1 temperature control
179 Central heating circuit 2 temperature control
217 Common error message
218 Pressure supervision error message
241 Outletprobe,solarprobeerror
242 Return probe, solar probe error
243 Pool temperature probe
31.1 ERROR/FAULT CODES
- 118 -
Error code Description320 DHW heat temperature probe
321 Instant error of DHW heater temperature probe
322 Water pressure 3 too high
323 Water pressure 3 too low
324 BX same probes
326 BX/same mixing valve unit probe
328 Same mixing valve unit function
329 Expansion module / same mixing valve unit function
330 BX1 no function
331 BX2 no function
332 BX3 no function
333 BX4 no function
339 Collector pump Q5 missing
340 Collector pump Q16 missing
341 Collector probe B6 missing
342 DHW solar probe B31 missing
343 Solar connection missing
344 Buffer solar controller K8 missing
345 Pool solar control element K18 missing
346 Wood-fired boiler pump Q10 missing
347 Wood-fired boiler comparison probe missing
348 Wood-fired boiler address error
349 Buffer tank return valve Y15 missing
350 Buffer tank address error
351 Primary control/system pump address error
353 Cascade probe B10 missing
366 Room temperature probe Hx error
Maintenance code Description1 Excess burner operating hours
2 Excess burner starts
3 Excess maintenance interval
5 Central heating circuit pressure too low (pressure below lower limit 1)
18 Central heating circuit pressure too low (pressure below lower limit 2)
21 Excessive maximum flue gas temperature
22 Central heating circuit pressure too low (pressure below lower limit 3)
Function code Description301 Manual operation
302 Thermostat test
303 Chimney sweep function
309 Outsidetemperaturesimulation
310 Alternative energy operation
314 Economy mode
31.2 MAINTENANCE WARNING CODES
31.3 SPECIAL FUNCTION CODES
- 119 -
GB
32. EXAMPLES OF POSSIBLE LAYOUTS (PARTIAL DIAGRAMS AND AUXILIARY FUNCTIONS)
32.1 KEY
General abbreviations
BX Multi-function/probe inputHX (H1 and H3) Low voltage (0-10V) multi-function inputMG MixingunitQX Multi-function/relay outputUX Low voltage (0-10V) multi-function input LP Line/parameter
Key High voltage
K6 DHW immersion heaterK4 Burner stage 1K5 Burner stage 2K8 Buffer tank control elementK9 OutsideheatexchangerpumpK16 Buffer tank or combined buffer tank immersion heaterK17 Flue gas relayK18 Solar control element for poolK30 Assisted ignition fanQ1 Boiler pumpQ2 Central heating circuit (CR1) pumpQ3 DHW pumpQ4 DHW circulating pumpQ5 Solar pump collectorQ6 Central heating circuit (CR2) pumpQ10 Solid fuel boiler pumpQ11 Buffer tank fill pumpQ12 Bypass pumpQ15 Pump H1Q16 2nd solar collector pumpQ19 Pump H3Q25 Cascade pumpQ33 Intermediate central heating circuit pumpQ34 Instant DHW heater pumpY4 Generalheatsourceshut-offvalveY7/Y8 Mixingvalvetomaintainreturntemperatureinboiler(OPEN/CLOSE)Y15 Buffer tank return valveY17/Y18 Burnermodulation(OPEN/CLOSE)Y25/Y26 Mixingvalvetomaintainreturntemperatureincascade(OPEN/CLOSE)Y31/Y32 DHWprimarycontrolmixingvalve(OPEN/CLOSE)Y33/Y34 InstantDHWheatervalve(OPEN/CLOSE)
Low voltage key
B2 Boiler outlet probeB3 DHW storage cylinder probe (top)B4 Buffer tank probe (top)B6 Solar collector probeB7 Boiler return probeB8 Flue gas temperature probeB10 Common outlet probe (cascade)B13 Temperature pool probeB22 Solid fuel boiler probe (outlet)B31 DHW storage cylinder probe (bottom)B36 DHW heat probeB38 Instant DHW heater outlet probeB39 DHW circulation probeB41 Buffer tank probe (bottom)B42 Buffer tank probe (middle)B61 Second solar collector probeB63 Solar outlet probe (high temperature)B64 Solar return probe (low temperature)B70 Cascade return probeB73 Primary circuit common return probeFS Flow switch
- 120 -
HEAT GENERATOR
Multistage oil/gas
REQUIRED SETTINGS: QX: - Boiler pump Q1 LP5770 (SOURCE TYPE): - 1-stage, or - Without boiler probe
OPTIONAL SETTINGS BX: - Return probe B7 - Recirculating (bypass) pump Q12
REQUIRED SETTINGS: QX:- Anti-condensation pump Q12LP5770 (Source type): - 1-stage, or - Without boiler probe
OPTIONAL SETTINGS BX: - Return probe B7
REQUIRED SETTINGS:QX:- Boiler pump Q1 - Anti-condensation pump Q12 OL5770 (Source type): - 1-stage, or - Without boiler probe
OPTIONAL SETTINGSBX:- Return sensor B7
REQUIRED SETTINGS: LP5770 (SOURCE TYPE): - 1-stage, or - Without boiler probe
OPTIONAL SETTINGS BX: - Return probe B7
B2
B7
K4
K4
K4
K5
OeG1
OeG2
OeG3
B2
B2
B2
Q1
B7
B7
B7
K4/K5
T
T
T
T
T
T
T
T
REQUIRED SETTINGS: LP5770 (SOURCE TYPE): - 2-stage, or - 2 x 1 cascade
OPTIONAL SETTINGS BX: - Return probe B7
B2
B7
K4
K4
K4
K5
OeG1
OeG2
OeG3
B2
B2
B2
Q1
B7
B7
B7
K4/K5
T
T
T
T
T
T
T
T
B2
B7
K4
K4
K4
K5
OeG1
OeG2
OeG3
B2
B2
B2
Q1
B7
B7
B7
K4/K5
T
T
T
T
T
T
T
T
OeG4
OeG5
OeG6
B2
B2
B2
B2
B2
B7
B7
B7
B7
B7
K4/K5
K4/K5
Q1
Q2
K5 K4
K5 K4
K4
Q1
Q12
Q12
Q12
T
T
T
T
T
T
T
T
T
T
OeG7
OeG8
OeG9
B7
K4
Q1 Q12
B2 T
T
B2 T
B2 T
B7 T
B7T
B7T
B2T
K4/K5
K4
K4K5
Q1 Q12
Q1Q1Q12
Q1
Y7/Y8
OeG4
OeG5
OeG6
B2
B2
B2
B2
B2
B7
B7
B7
B7
B7
K4/K5
K4/K5
Q1
Q2
K5 K4
K5 K4
K4
Q1
Q12
Q12
Q12
T
T
T
T
T
T
T
T
T
T
OeG4
OeG5
OeG6
B2
B2
B2
B2
B2
B7
B7
B7
B7
B7
K4/K5
K4/K5
Q1
Q2
K5 K4
K5 K4
K4
Q1
Q12
Q12
Q12
T
T
T
T
T
T
T
T
T
T
REQUIRED SETTINGS: QX:- Boiler pump Q1 LP5770 (Source type): - 2-stage, or - 2 x 1 cascade
OPTIONAL SETTINGS BX:- Return probe B7
Note: With two boilers in casca-de connect pumps Q1 to termi-nals QX1, QX2.
REQUIRED SETTINGS: QX:- Anti-condensation pump Q12 OL5770 (Source type): - 2-stage, or - 2 x 1 cascade
OPTIONAL SETTINGSBX:- Return sensor B7
HEAT GENERATOR
Multistage oil/gas
32.2 LAYOUTS
- 121 -
GB
HEAT GENERATOR
Multistage oil/gas
OeG7
OeG8
OeG9
B7
K4
Q1 Q12
B2 T
T
B2 T
B2 T
B7 T
B7T
B7T
B2T
K4/K5
K4
K4K5
Q1 Q12
Q1Q1Q12
Q1
Y7/Y8
OeG11
OeG12
OeG13
OeG14
OeG15
B2 T
B2 T
B7T
B7T
B7T
B7T
B7 T
UXY17/Y18
UXY17/Y18
UXY17/Y18
UXY17/Y18
UXY17/Y18
Q1
Q1 Q12
Q12
Q1
Y7/Y8
K4
B2 T
B2 T
B2 T
K4
K4
K4
K4
OeG11
OeG12
OeG13
OeG14
OeG15
B2 T
B2 T
B7T
B7T
B7T
B7T
B7 T
UXY17/Y18
UXY17/Y18
UXY17/Y18
UXY17/Y18
UXY17/Y18
Q1
Q1 Q12
Q12
Q1
Y7/Y8
K4
B2 T
B2 T
B2 T
K4
K4
K4
K4
OeG11
OeG12
OeG13
OeG14
OeG15
B2 T
B2 T
B7T
B7T
B7T
B7T
B7 T
UXY17/Y18
UXY17/Y18
UXY17/Y18
UXY17/Y18
UXY17/Y18
Q1
Q1 Q12
Q12
Q1
Y7/Y8
K4
B2 T
B2 T
B2 T
K4
K4
K4
K4
OeG11
OeG12
OeG13
OeG14
OeG15
B2 T
B2 T
B7T
B7T
B7T
B7T
B7 T
UXY17/Y18
UXY17/Y18
UXY17/Y18
UXY17/Y18
UXY17/Y18
Q1
Q1 Q12
Q12
Q1
Y7/Y8
K4
B2 T
B2 T
B2 T
K4
K4
K4
K4
OeG11
OeG12
OeG13
OeG14
OeG15
B2 T
B2 T
B7T
B7T
B7T
B7T
B7 T
UXY17/Y18
UXY17/Y18
UXY17/Y18
UXY17/Y18
UXY17/Y18
Q1
Q1 Q12
Q12
Q1
Y7/Y8
K4
B2 T
B2 T
B2 T
K4
K4
K4
K4
OeG7
OeG8
OeG9
B7
K4
Q1 Q12
B2 T
T
B2 T
B2 T
B7 T
B7T
B7T
B2T
K4/K5
K4
K4K5
Q1 Q12
Q1Q1Q12
Q1
Y7/Y8
OeG10
B2 T
B7T
B2T
B7 T
Q1
Y7/Y8
K4/K5
K4K5
Q1Q1
Y7/Y8
REQUIRED SETTINGS:MG (LP6014, 6015):- Maintained return temperatureLP5770 (Source Type): - 1-stage, or - Without boiler probe
REQUIRED SETTINGS:QX:- Boiler pump Q1 - Recirculating (bypass) pump Q12 LP5770 (Source Type): - 2-stage, or - 2 x 1 cascade
OPTIONAL SETTINGS:BX:- Return probe B7
Note: With two boilers in casca-de connect pumps Q1 to termi-nals QX1, QX2.
REQUIRED SETTINGS:LP5770 (Source Type): - 3-position modulating, or - UX modulating
OPTIONAL SETTINGSBX:- Return probe B7
REQUIRED SETTINGS:QX:-BOILERPUMPQ1LP5770 (Source Type): - 3-position modulating, or - UX modulating
OPTIONAL SETTINGSBX:- Return probe B7
REQUIRED SETTINGS:QX:- Recirculating (bypass) pump Q12 LP5770 (Source Type): - 3-position modulating, or - UX modulating
OPTIONAL SETTINGSBX:- Return probe B7
REQUIRED SETTINGS:QX:- Boiler pump Q1 - Recirculating (bypass) pump Q12 LP5770 (Source Type): - 3-position modulating, or - UX modulating
OPTIONAL SETTINGSBX:- Return probe B7
REQUIRED SETTINGS:MG (LP6014, 6015):- Maintained return temperatureLP5770 (Source Type): - 3-position modulating, or - UX modulating
REQUIRED SETTINGS:MG (LP6014, 6015):- Maintained return temperatureLP5770 (Source Type): - 2-stage, or - 2 x 1 cascade
Note: For 2x1 cascade, set boiler pump Q1 to QX1, QX2.
HEAT GENERATOR Modulating oil/gas
HEAT GENERATORMultistage oil/gas
- 122 -
REQUIRED SETTINGS:QX: - Solid fuel: Boiler pump Q10 BX: - Solid fuel: boiler probe B22 OL4133 (∆T M/R control): -Outlettemperaturesetpoint,or- Minimum set point
REQUIRED SETTINGS:QX: - Solar collector pump Q5 BX: - Solar collector sensor B6
OPTIONAL SETTINGSUX:- Q5
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Secondary exchanger loop pump K9 BX: - Solar collector probe B6
OPRIONAL SETTINGSUX:- Q5 / K9
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar control component: buffer tank K8 BX: - Solar collector probe B6 LP5840 (Solar control components): - Fill pump
OPTIONAL SETTINGS:UX:- Q5 / K8
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar control component: buffer tank K8 BX: - Solar collector probe B6 LP5840 (Solar control components):- Selector valve
OPTIONAL SETTINGSUX:- Q5
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar control component: buffer tank K8 - Sec. exchanger loop pump K9 BX: - Solar collector probe B6 LP5840 (Solar control comp.):- Fill pump LP5841 (Outside solar exchanger):- Jointly
OPTIONAL SETTINGSUX:- Q5 / K8 / K9
REQUIRED SETTINGS:QX: - Solid fuel: Boiler pump Q10 BX: - Solid fuel: boiler probe B22 OL4133 (∆T M/R control): - DHW probe B3, or - DHW probe B31, or - Storage (buffer tank) probe B4, or - Storage (buffer tank) probe B41
REQUIRED SETTINGS:BX: - Flue gas temp. sensor B8
OPTIONAL SETTINGSQX:- Flue gas relay K17 - Safety fan K30
HEAT GENERATOR Solid fuel: (wood)
SOLAR THERMAL One-collector system
B22 T
B22 T
T
Q10
Q10
B8
T
Q5
B6 T
B6 T
B6T
Q5
K9
Q5
K8
T
T
Q5
B6 T
B6 T
B6T
Q5
K9
Q5
K8
T
T
Q5
B6 T
B6 T
B6T
Q5
K9
Q5
K8
T
T
0
1
T
T
T
T
B6T
B6T
Q5
Q5
K8
K9
K8
0
1
T
T
T
T
B6T
B6T
Q5
Q5
K8
K9
K8
B22 T
B22 T
T
Q10
Q10
B8
T
B22 T
B22 T
T
Q10
Q10
B8
T
EXTRA OIL/GAS-FIRED AND SOLID FUEL HEAT GENERATOR FUNCTIONS
- 123 -
GB0
1
T
T
T
T
B6T
B6T
Q5
Q5 K9
K8
K9
K8
0
1
T
T
T
T
B6T
B6T
Q5
Q5 K9
K8
K9
K8
0
1
T
B6T
B6T
Q5
Q5
K8 K9
K9
K8
T
T
T
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar control component: buffer tank K8 - Sec. exchanger loop pump K9 BX: - Solar collector sensor B6 LP5840 (Solar control comp.): - Selector valve LP5841 (Outside solar exchanger): - Insieme
OPTIONAL SETTINGSUX: Q5 / K9
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar control component: buffer tank K8 - Sec. exchanger loop pump K9 BX: - Solar collector probe B6 LP5840 (Solar control comp.): - Fill pump LP5841 (Outside solar exchanger): - DHW storage
OPTIONAL SETTINGSUX: Q5 / K8 / K9
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar control component: buffer tank K8 - Sec. exchanger loop pump K9 BX: - Solar collector probe B6 LP5840 (Solar control comp.): - Selector valve LP5841 (Outside solar exchanger): - DHW storage
OPTIONAL SETTINGSUX: Q5 / K9
0
1
T
B6T
B6T
Q5
Q5
K8 K9
K9
K8
T
T
T
0
1
0
1
B6T
B6T
B6T
Q5
K8
K9
K18
Q5
Q5
K18
T
T
T
T
T
T
0
1
0
1
B6T
B6T
B6T
Q5
K8
K9
K18
Q5
Q5
K18
T
T
T
T
T
T
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar control component: buffer tank K8 - Sec. exchanger loop pump K9 BX: - Solar collector probe B6 LP5840 (Solar control comp.): - Fill pump LP5841 (Outside solar exchanger): - Storage (buffer tank) probe
OPTIONAL SETTINGS UX: Q5 / K8 / K9
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar control component: buffer tank K8 - Sec. exchanger loop pump K9 BX: - Solar collector probe B6 LP5840 (Solar control comp.): - Selector valve LP5841 (Outside solar exchanger): - Storage (buffer tank) probe)
OPTIONAL SETTINGSUX: Q5 / K9
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar control component: pool K18 BX: - Solar collector probe B6 LP5840 (Solar control comp.): - Fill pump
OPTIONAL SETTINGSUX: Q5 / K18
SOLAR THERMAL One-collector system
SOLAR THERMAL One-collector system
- 124 -
SOLAR THERMAL One-collector system
SOLAR THERMAL One-collector system
0
1
0
1
B6T
B6T
B6T
Q5
K8
K9
K18
Q5
Q5
K18
T
T
T
T
T
T
0
1
B6T
B6T
B6T
Q5
Q5
K9
K9
K18
K18
Q5
K8
K18
T
T
T
T
T
T
T
0
1
B6T
B6T
B6T
Q5
Q5
K9
K9
K18
K18
Q5
K8
K18
T
T
T
T
T
T
T
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar control component: buffer tank K8 - Solar control component: pool K18 BX: - Solar collector probe B6 LP5840 (Solar control comp.): - Selector valve
OPTIONAL SETTINGSUX: Q5
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Sec. exchanger loop pump K9 - Solar control component: pool K18 BX: - Solar collector probe B6 LP5840 (Solar control comp.): - Fill pump
OPTIONAL SETTINGS:UX: Q5 / K9 / K18
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Sec. exchanger loop pump K9 - Solar control component: pool K18 BX: - Solar collector probe B6 LP5840 (Solar control comp.): - Selector valve
OPTIONAL SETTINGSUX: Q5 / K9
0
1
B6T
B6T
B6T
Q5
Q5
K9
K9
K18
K18
Q5
K8
K18
T
T
T
T
T
T
T
0101
B6T
B6T
T
T
T
T
T
T
Q5
Q5 K9
K8
K18
K18 K8010
1
B6T
B6T
T
T
T
T
T
T
Q5
Q5 K9
K8
K18
K18 K8
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar control component: buffer tank K8 - Solar control component: pool K18 BX: - Solar collector probe B6 LP5840 (Solar control comp.): - Fill pump
OPTIONAL SETTINGSUX: Q5 / K8 / K18
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar control component: buffer tank K8 - Solar control component: pool K18 BX: - Solar collector probe B6 LP5840 (Solar control comp.): - Select valve
OPTIONAL SETTINGS:UX: Q5
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar control component: buffer tank K8 - Sec. exchanger loop pump K9 - Solar control component: pool K18 BX: - Solar collector probe B6LP5840 (Solar control comp.): - Fill pump LP5841 (Outside solar exchanger): - Together
OPTIONAL SETTINGSUX: Q5 / K8 / K9 / K18
- 125 -
GB
B6T
B6T
Q5
Q5 K9
K9
K8
K8
K18
K18
T
T
T
T
T
T
B6T
B6T
Q5
Q5 K9
K9
K8
K8
K18
K18
T
T
T
T
T
T
B6T
B6T
B6T
Q5
Q5
K9
K8K18
Q5
K9
K9
K8
K18
K8K18
T
T
T
T
T
T
T
T
T
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar control component: buffer tank K8 - Sec. exchanger loop pump K9 - Solar control component: pool K18 BX: - Solar collector probe B6 LP5840 (Solar control comp.): - Selector valve LP5841 (Outside solar exchanger): - Together
OPTIONAL SETTINGSUX: Q5 / K9
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar control component: buffer tank K8 - Sec. exchanger loop pump K9 - Solar control component: pool K18 BX: - Solar collector probe B6 LP5840 (Solar control comp.): - Fill pump LP5841 (Outside solar exchanger): - DHW storage
OPTIONAL SETTINGSUX: Q5 / K8 / K9 / K18
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar control component: buffer tank K8 - Sec. exchanger loop pump K9 - Solar control component: pool K18 BX: - Solar collector probe B6LP5840 (Solar control comp.): - Selector valve LP5841 (Outside solar exchanger): - DHW storage
OPTIONAL SETTINGSUX: Q5 / K9
B6T
B6T
B6T
Q5
Q5
K9
K8K18
Q5
K9
K9
K8
K18
K8K18
T
T
T
T
T
T
T
T
T
B6T
B6T
B6T
Q5
Q5
K9
K8K18
Q5
K9
K9
K8
K18
K8K18
T
T
T
T
T
T
T
T
T
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar control component: buffer tank K8 - Sec. exchanger loop pump K9 - Solar control component: pool K18 BX: - Solar collector probe B6 LP5840 (Solar control comp.): - Fill pump LP5841 (Outside solar exchanger): - Storage (buffer tank) probe
OPTIONAL SETTINGSUX: Q5 / K8 / K9 / K18
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar control component: buffer tank K8 - Sec. exchanger loop pump K9 - Solar control component: pool K18 BX: - Solar collector probe B6LP5840 (Solar control comp.): - Selector valve LP5841 (Outside solar exchanger): - Storage (buffer tank) probe
OPTIONAL SETTINGSUX: Q5 / K9
SOLAR THERMAL One-collector system
SOLAR THERMAL One-collector system
- 126 -
T
B6 T T B61
Q5 Q16
B6 T T B61
Q5 Q16
T
K9
B6 T T B61
T
T
Q5 Q16
K8
B6 T T B61
Q5 Q16
T
T
K8
K9
T
B6 T T B61
Q5 Q16
B6 T T B61
Q5 Q16
T
K9
B6 T T B61
T
T
Q5 Q16
K8
B6 T T B61
Q5 Q16
T
T
K8
K9
T
B6 T T B61
Q5 Q16
B6 T T B61
Q5 Q16
T
K9
B6 T T B61
T
T
Q5 Q16
K8
B6 T T B61
Q5 Q16
T
T
K8
K9
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar collector 2 pump Q16 BX: - Solar collector probe B6 - Solar collector probe B61
OPTIONAL SETTINGSUX: Q5 / Q16
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar collector 2 pump Q16 - Sec. exchanger loop pump K9 BX: - Solar collector probe B6 - Solar collector probe B61
OPTIONAL SETTINGSUX: Q5 / Q16 / K9
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar collector 2 pump Q16 - Solar control component: buffer tank K8 BX: - Solar collector probe B6 - Solar collector probe B61
OPTIONAL SETTINGSUX: Q5 / Q16
T
B6 T T B61
Q5 Q16
B6 T T B61
Q5 Q16
T
K9
B6 T T B61
T
T
Q5 Q16
K8
B6 T T B61
Q5 Q16
T
T
K8
K9
Sol38
Sol 39
B6 T T B61
Q5Q16
K8
K9
T
T
B6 T T B61
Q5Q16 K8
K9
T
T
Sol38
Sol 39
B6 T T B61
Q5Q16
K8
K9
T
T
B6 T T B61
Q5Q16 K8
K9
T
T
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar collector 2 pump Q16 - Solar control component: buffer tank K8 - Sec. exchanger loop pump K9 BX: - Solar collector probe B6 - Solar collector probe B61 LP5840 (Solar control comp.): - Fill pump LP5841 (Outside solar exchanger): - Together
OPTIONAL SETTINGSUX: Q5 / Q16 / K8 / K9
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar collector 2 pump Q16 - Solar control component: buffer tank K8 - Sec. exchanger loop pump K9 BX: - Solar collector probe B6 - Solar collector probe B61 LP5840 (Solar control comp.):- Selector valve LP5841 (Outside solar exchanger): - Together
OPTIONAL SETTINGSUX: Q5 / Q16 / K9
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar collector 2 pump Q16 - Solar control component: buffer tank K8 - Sec. exchanger loop pump K9 BX: - Solar collector probe B6 - Solar collector probe B61 LP5840 (Solar control comp.): - Fill pump LP5841 (Outside solar exchanger): - DHW storage
OPTIONAL SETTINGSUX: Q5 / Q16 / K8 / K9
SOLAR THERMAL Two-collector system
SOLAR THERMAL Two-collector system
- 127 -
GB
Sol40
Sol41
B6 T T B61
Q5Q16
K8
K9
T
T
B6 T T B61
Q5Q16
K8
K9
T
T
Sol40
Sol41
B6 T T B61
Q5Q16
K8
K9
T
T
B6 T T B61
Q5Q16
K8
K9
T
T
Sol42
Sol44
B6 T T B61
Q5Q16
K18
T
T
B6 T T B61
Q5Q16 K18
K9
T
T
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar collector 2 pump Q16 - Solar control component: buffer tank K8 - Sec. exchanger loop pump K9 BX: - Solar collector probe B6 - Solar collector probe B61 LP5840 (Solar control comp.): - Selector valve LP5841 (Outside solar exchanger): - DHW storage
OPTIONAL SETTINGSUX: Q5 / Q16 / K9
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar collector 2 pump Q16 - Solar control component: buffer tank K8 - Sec. exchanger loop pump K9 BX: - Solar collector probe B6 - Solar collector probe B61 LP5841 (Outside solar exchanger): - Storage (buffer tank) probe
OPTIONAL SETTINGSUX: Q5 / Q16 / K9
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar collector 2 pump Q16 - Solar control component: pool K18 BX: - Solar collector probe B6 - Solar collector probe B61
OPTIONAL SETTINGSUX: Q5 / Q16
Sol42
Sol44
B6 T T B61
Q5Q16
K18
T
T
B6 T T B61
Q5Q16 K18
K9
T
T
Sol45
Sol46
B6 T T B61
Q5Q16
K18
K9
T
T
B6 T T B61
Q5Q16
K18 K9
T
T
T
Sol45
Sol46
B6 T T B61
Q5Q16
K18
K9
T
T
B6 T T B61
Q5Q16
K18 K9
T
T
T
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar collector 2 pump Q16 - Sec. exchanger loop pump K9 - Solar control component: pool K18 BX: - Solar collector probe B6 - Solar collector probe B61 LP5840 (Solar control comp.): - Fill pump
OPTIONAL SETTINGSUX: Q5 / Q16 / K9 / K18
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar collector 2 pump Q16 - Sec. exchanger loop pump K9 - Solar control component: pool K18 BX: - Solar collector probe B6 - Solar collector probe B61 LP5840 (Solar control comp.): - Selector valve
OPTIONAL SETTINGSUX: Q5 / Q16 / K9
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar collector 2 pump Q16 - Solar control component: buffer tank K8 - Solar control component: pool K18 BX: - Solar collector probe B6 - Solar collector probe B61
OPTIONAL SETTINGSUX: Q5 / Q16
SOLAR THERMAL Two-collector system
SOLAR THERMAL Two-collector system
- 128 -
Sol48
Sol49 B6 T T B61
B6 T T B61
Q5Q16
Q5Q16
K18
K9
K8
K18
K9
K8
T
T
T
T
T
T
Sol48
Sol49 B6 T T B61
B6 T T B61
Q5Q16
Q5Q16
K18
K9
K8
K18
K9
K8
T
T
T
T
T
T
So l50
Sol51
B6 T T B61
Q5Q16
K18
K9
K8
T
T
T
B6 T T B61
Q5Q16
K18
K9
K8
T
T
T
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar collector 2 pump Q16 - Solar control component: buffer tank K8 - Sec. exchanger loop pump K9 - Solar control comp. pool K18 BX: - Solar collector probe B6 - Solar collector probe B61 LP5840 (Solar control comp.): - Fill pump LP5841 (Outside solar exchanger): - Together OPTIONAL SETTINGSUX: Q5 / Q16 / K8 / K9 / K18
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar collector 2 pump Q16 - Solar control component: buffer tank K8 - Sec. exchanger loop pump K9 - Solar control comp. pool K18 BX: - Solar collector probe B6 - Solar collector probe B61 LP5840 (Solar control comp.): - Selector valve LP5841 (Outside solar exchanger): - Together OPTIONAL SETTINGSUX: Q5 / Q16 / K9
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar collector 2 pump Q16 - Solar control component: buffer tank K8 - Sec. exchanger loop pump K9 - Solar control comp.: pool K18 BX: - Solar collector probe B6 - Solar collector probe B61 LP5840 (Solar control comp.): - Fill pump LP5841 (Outside solar exchanger): - DHW storage OPTIONAL SETTINGSUX: Q5 / Q16 / K8 / K9 / K18
So l50
Sol51
B6 T T B61
Q5Q16
K18
K9
K8
T
T
T
B6 T T B61
Q5Q16
K18
K9
K8
T
T
T
T M/R
B6 T T B61
Q5Q16
K18
K9
K8
T
T
T
B63
B64
T
T
T
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar collector 2 pump Q16 - Solar control component: buffer tank K8 - Sec. exchanger loop pump K9 - Solar control comp. pool K18 BX: - Solar collector probe B6 - Solar collector probe B61 LP5840 (Solar control comp.): - Selector valve LP5841 (Outside solar exchanger): - DHW storage OPTIONAL SETTINGSUX: Q5 / Q16 / K9
REQUIRED SETTINGS:QX: - Solar collector pump Q5 - Solar collector 2 pump Q16 - Solar control component: buffer tank K8 - Sec. exchanger loop pump K9 - Solar control comp. pool K18 BX: - Solar collector probe B6 - Solar collector probe B61 LP5841 (Outside solar exchanger): - Storage (buffer tank) probe OPTIONAL SETTINGSUX: Q5 / Q16 / K9
REQUIRED SETTINGS:BX: - Solar delivery probe B63 (hot) - Solar return probe B64 (cold)
SOLAR THERMAL Two-collector system
SOLAR THERMAL Two-collector system
T M/R
B6 T T B61
Q5Q16
K18
K9
K8
T
T
T
B63
B64
T
T
T
EXTRA SOLAR THERMAL FUNCTIONS
- 129 -
GB
Sp1
01
01
Sp2
Sp4
Sp5
B4T
B42T
B41T
B4T
B42T
B41T
B4
Y4
Y4
T
B42T
B41T
B4T
B42T
B41T
Exchanger
Sola
r
Exchanger
Sola
r
0
1
0
1
K16
Valvola miscelatrice sul ritorno
Valvola parzializzatrice
Circolatore di tras ferimento
Electrical immersion heater buf fer
B4/B41/B42T
B73T
Y15
B4/B41/B42
B4
B41
T
Y15
Q11
B3/B31T T
T
B4 T
Sp1
01
01
Sp2
Sp4
Sp5
B4T
B42T
B41T
B4T
B42T
B41T
B4
Y4
Y4
T
B42T
B41T
B4T
B42T
B41T
Exchanger
Sola
r
Exchanger
Sola
r
0
1
0
1
K16
Valvola miscelatrice sul ritorno
Valvola parzializzatrice
Circolatore di tras ferimento
Electrical immersion heater buf fer
B4/B41/B42T
B73T
Y15
B4/B41/B42
B4
B41
T
Y15
Q11
B3/B31T T
T
B4 T
Sp1
01
01
Sp2
Sp4
Sp5
B4T
B42T
B41T
B4T
B42T
B41T
B4
Y4
Y4
T
B42T
B41T
B4T
B42T
B41T
Exchanger
Sola
r
Exchanger
Sola
r
0
1
0
1
K16
Valvola miscelatrice sul ritorno
Valvola parzializzatrice
Circolatore di tras ferimento
Electrical immersion heater buf fer
B4/B41/B42T
B73T
Y15
B4/B41/B42
B4
B41
T
Y15
Q11
B3/B31T T
T
B4 T
Sp1
01
01
Sp2
Sp4
Sp5
B4T
B42T
B41T
B4T
B42T
B41T
B4
Y4
Y4
T
B42T
B41T
B4T
B42T
B41T
Exchanger
Sola
r
Exchanger
Sola
r
0
1
0
1
K16
Valvola miscelatrice sul ritorno
Valvola parzializzatrice
Circolatore di tras ferimento
Electrical immersion heater buf fer
B4/B41/B42T
B73T
Y15
B4/B41/B42
B4
B41
T
Y15
Q11
B3/B31T T
T
B4 T
REQUIRED SETTINGS:BX: - Storage (buffer tank) probe B4 OL4783 (With supplementary solar): - No
OPTIONAL SETTINGSBX: - Storage (buffer tank) probe B41 - Storage (buffer tank) probe B42
REQUIRED SETTINGS:QX: - Storage (buffer tank) return selector valve Y15 BX: - Storage (buffer tank) probe B4-GlobalreturnsensorB73
OPTIONAL SETTINGSBX: - Storage (buffer tank) probe B41 - Storage (buffer tank) probe B42
REQUIRED SETTINGS:BX: - Storage (buffer tank) probe B4 OL4783 (With supplementary solar): - Yes
OPTIONAL SETTINGSBX: - Storage (buffer tank) probe B41 - Storage (buffer tank) probe B42
REQUIRED SETTINGS:QX: - Storage (buffer tank) return selector valve Y15 BX: - Storage (buffer tank) probe B4
OPTIONAL SETTINGSBX: - Storage (buffer tank) probe B41 - Storage (buffer tank) probe B42
REQUIRED SETTINGS:QX: - Heat generator shutoff valve Y4 BX: - Storage (buffer tank) probe B4 LP4783 (With supplementary solar): - No
OPTIONAL SETTINGSBX: - Storage (buffer tank) probe B41 - Storage (buffer tank) probe B42
REQUIRED SETTINGS:QX: - Stor tank transfer Pump Q11
OPTIONAL SETTINGSBX: - DHW probe B31
REQUIRED SETTINGS:QX: - Heat generator shutoff valve Y4 BX: - Heat generator shutoff valve Y4 LP4783 (Con integrazione solare):- Si
OPTIONAL SETTINGSBX: - Storage (buffer tank) probe B41 - Storage (buffer tank) probe B42
REQUIRED SETTINGS:QX: - El imm heater buffer K16
STORAGE TEMPERATURE CONTROLBuffer tank temperature control
STORAGE TEMPERATURE CONTROLExtra buffer temperature control functions
- 130 -
DHW STORAGE Without circulating pump
DHW STORAGEWith circulating pump
TWWSp1
TWWSp2
TB3
TB31
TB3
TB31
01
TWWSp4
TWWSp5
TWWSp13
TB3
TB31
T
B36
Q3
TB3
TB31
T
B36
Q3
TB3
TB31
Q3
Sola
r
01
TWWSp4
TWWSp5
TWWSp13
TB3
TB31
T
B36
Q3
TB3
TB31
T
B36
Q3
TB3
TB31
Q3
Sola
r
TWWSp1
TWWSp2
TB3
TB31
TB3
TB31
REQUIRED SETTINGS:LP5093 (With supplementary solar): - NoLP5731:- None
OPTIONAL SETTINGS:BX: - DHW probe B31
REQUIRED SETTINGS:LP5093 (With supplementary solar): - NoLP5731 (DHW control component Q3): - fill circuit
OPTIONAL SETTINGS:BX: - DHW probe B31 - DHW fill probe B36 UX: - Intermediate DHW circuit pump Q33
REQUIRED SETTINGS:LP5093 (With supplementary solar): - Yes LP5731 (DHW control component Q3): - fill circuit
OPTIONAL SETTINGS:BX: - DHW probe B31 - DHW fill probe B36 UX: - Intermediate DHW circuit pump Q33
REQUIRED SETTINGS:LP5093 (With supplementary solar): - Yes LP5731 (DHW control component Q3): - None
OPTIONAL SETTINGS:BX: - DHW probe B31
REQUIRED SETTINGS:LP5093 (With supplementary solar): - NoLP5731 (DHW control component Q3): - Selector valve
IMPOSTAZIONI OPZIONALI:BX: - DHW probe B31
REQUIRED SETTINGS:LP5093 (With supplementary solar): - Yes LP5731 (DHW control component Q3): - Selector valve
OPTIONAL SETTINGS:BX: - DHW probe B31
DHW STORAGE
With mixing valve
01
TWWSp4
TWWSp5
TWWSp13
TB3
TB31
T
B36
Q3
TB3
TB31
T
B36
Q3
TB3
TB31
Q3
Sola
r
01
TWWSp14
TWWSp16
TWWSp17
TB3
TB31
Q3
TB3
TB31
T
B35Q3
Y31/Y32
TB3
TB31
T
B35Q3Y31/Y32
Sola
r
Sola
r
- 131 -
GB
DHW STORAGE With heat exchanger for filling the storage tank
01
TWWSp14
TWWSp16
TWWSp17
TB3
TB31
Q3
TB3
TB31
T
B35Q3Y31/Y32
TB3
TB31
T
B35Q3Y31/Y32
Sola
r
Sola
r
TWWSp19
TWWSp20
T
B36
T
B36
TB3
TB3
TB31
TB31
Q33
Q33
Sola
r
TWWSp19
TWWSp20
T
B36
T
B36
TB3
TB3
TB31
TB31
Q33
Q33
Sola
r
TWWSp22
TWWSp23
T
B36
T
B36
TB3
TB31
TB3
TB31
Q33
Q3
Q33
Q3
Sola
r
TWWSp22
TWWSp23
T
B36
T
B36
TB3
TB31
TB3
TB31
Q33
Q3
Q33
Q3
Sola
r
01
TWWSp14
TWWSp16
TWWSp17
TB3
TB31
Q3
TB3
TB31
T
B35Q3Y31/Y32
TB3
TB31
T
B35Q3Y31/Y32
Sola
r
Sola
r
REQUIRED SETTINGS:MG (LP6014, 6015): - DHW primary controller LP4783 (With supplementary solar): - No
OPTIONAL SETTINGSBX: - DHW probe B31
REQUIRED SETTINGS:QX: - Intermediate DHW circuit pump Q33 LP5731 (DHW control component Q3): - NoneLP5093 (With supplementary solar): - No
OPTIONAL SETTINGSBX: - DHW probe B31 - DHW fill probe B36 UX: - DHW pump Q3
REQUIRED SETTINGS:QX: - Intermediate DHW circuit pump Q33 LP5731 (DHW control component Q3): : - NoneLP5093 (With supplementary solar): - Yes
OPTIONAL SETTINGSBX: - DHW probe B31 - DHW fill probe B36 UX: - DHW pump Q3
REQUIRED SETTINGS:QX: - Intermediate DHW circuit pump Q33 LP5731 (DHW control component Q3): - Fill pump LP5093 (With supplementary solar): - No
OPTIONAL SETTINGS:BX: - DHW probe B31 - DHW fill probe B36 UX: - Intermediate DHW circuit pump Q33 - DHW pump Q3
REQUIRED SETTINGS:QX: - Intermediate DHW circuit pump Q33 LP5731 (DHW control component Q3): - Fill pump LP5093 (With supplementary solar): - Yes
OPTIONAL SETTINGS:BX: - DHW probe B31 - DHW fill probe B36 UX: - Intermediate DHW circuit pump Q33 - DHW pump Q3
REQUIRED SETTINGS:MG (LP6014, 6015):- DHW primary controllerLP4783 (With supplementary solar): - Yes LP5731 (DHW control component Q3): -None
OPTIONAL SETTINGS:BX: - DHW probe B31
DHW STORAGE
With fill pump and mixing valve
- 132 -
TWWSp25
TWWSp26
T
B36
TB3
TB31
Q33
Q3
T
B36
TB3
TB31
Q33
Q3
Sola
r
TWWSp25
TWWSp26
T
B36
TB3
TB31
Q33
Q3
T
B36
TB3
TB31
Q33
Q3
Sola
r
TWWSp28
TWWSp29
T
B36
TB3
TB31
Q33
Q3
Y31/Y32T
T
T
B36
TB3
TB31
Q33
Q3
Y31/Y32T
TB35
B35
Sola
r
TWWSp28
TWWSp29
T
B36
TB3
TB31
Q33
Q3
Y31/Y32T
T
T
B36
TB3
TB31
Q33
Q3
Y31/Y32T
TB35
B35
Sola
r
REQUIRED SETTINGS:QX: - Intermediate DHW circuit pump Q33 LP5731 (DHW control component Q3): - Selector valveLP5093 (With supplementary solar): -No
OPTIONAL SETTINGSBX: - DHW probe B31 - DHW fill probe B36 UX: - Intermediate DHW circuit pump Q33
REQUIRED SETTINGS:QX: - Intermediate DHW circuit pump Q33 LP5731 (DHW control component Q3): - Selector valveLP5093 (With supplementary solar):- Yes
OPTIONAL SETTINGSBX: - DHW probe B31 - DHW fill probe B36 UX: - Intermediate DHW circuit pump Q33
REQUIRED SETTINGS:MG/EM: - DHW primary controllerQX: - Intermediate DHW circuit pump Q33 LP5093 (With supplementary solar): - No
OPTIONAL SETTINGSBX: - DHW probe B31 - DHW fill probe B36 UX: - Intermediate DHW circuit pump Q33
REQUIRED SETTINGS:MG/EM: - DHW primary controllerQX: - Intermediate DHW circuit pump Q33 LP5093 (With supplementary solar): - Yes
OPTIONAL SETTINGSBX: - DHW probe B31 - DHW fill probe B36 UX: - Intermediate DHW circuit pump Q33
DHW STORAGE With heat exchanger for filling the storage tank
DHW STORAGE With heat exchanger for instant production
FS
Input
FS Input Hx
TWWDl3
TWWDl8
Circolatore sanitario
Electrical immersion heater Accumulo sanitario
T
B38
Q34
T
B38
Q34
Y33/Y34
TB39
FST
B39
TB39
TB3
Q3
K6
Hx
Input Hx
Q4
Q4
FS
Input
FS Input Hx
TWWDl3
TWWDl8
Circolatore sanitario
Electrical immersion heater Accumulo sanitario
T
B38
Q34
T
B38
Q34
Y33/Y34
TB39
FST
B39
TB39
TB3
Q3
K6
Hx
Input Hx
Q4
Q4
FS
Input
FS Input Hx
TWWDl3
TWWDl8
Circolatore sanitario
Electrical immersion heater Accumulo sanitario
T
B38
Q34
T
B38
Q34
Y33/Y34
TB39
FST
B39
TB39
TB3
Q3
K6
Hx
Input Hx
Q4
Q4
FS
Input
FS Input Hx
TWWDl3
TWWDl8
Circolatore sanitario
Electrical immersion heater Accumulo sanitario
T
B38
Q34
T
B38
Q34
Y33/Y34
TB39
FST
B39
TB39
TB3
Q3
K6
Hx
Input Hx
Q4
Q4
REQUIRED SETTINGS:QX: - Primary exchanger loop pump Q34 BX: - Sensor domestic hot water outlet B38 OPTIONAL SETTINGSUX: - Primary exchanger loop pump Q34
Note:-RequiresDHWstorage
REQUIRED SETTINGS:QX: - Pump Q4
OPTIONAL SETTINGSBX: - DHW circulation probe B39
REQUIRED SETTINGS:QX: - DHW electric heater K6
REQUIRED SETTINGS:MG (LP6014, 6015): - Instant DHW heater QX: - Primary heat loop pump Q34 BX: - DHW outlet probe B38
OPTIONAL SETTINGS:BX: - DHW circulation probe B39
Note:- DHWstoragerequired
- 133 -
GB
Sb1
Sb2
Sb3
Sb4
T
B13
T
B13
T
B13
Q15/Q19
T
B13
Q15/Q19
Separatore idrau l ico
HWe1
HWe2
HWe3
HWe4
HWe6
T
B10
T
B10
TB70
T
B10
TB70
Q25
T
B10
TB70
Q25
Y25/Y26
Separatore idrau l ico
HWe1
HWe2
HWe3
HWe4
HWe6
T
B10
T
B10
TB70
T
B10
TB70
Q25
T
B10
TB70
Q25
Y25/Y26
Separatore idrau l ico
HWe1
HWe2
HWe3
HWe4
HWe6
T
B10
T
B10
TB70
T
B10
TB70
Q25
T
B10
TB70
Q25
Y25/Y26
Separatore idrau l ico
HWe1
HWe2
HWe3
HWe4
HWe6
T
B10
T
B10
TB70
T
B10
TB70
Q25
T
B10
TB70
Q25
Y25/Y26
Separatore idrau l ico
HWe1
HWe2
HWe3
HWe4
HWe6
T
B10
T
B10
TB70
T
B10
TB70
Q25
T
B10
TB70
Q25
Y25/Y26
Sb1
Sb2
Sb3
Sb4
T
B13
T
B13
T
B13
Q15/Q19
T
B13
Q15/Q19
Sb1
Sb2
Sb3
Sb4
T
B13
T
B13
T
B13
Q15/Q19
T
B13
Q15/Q19
Sb1
Sb2
Sb3
Sb4
T
B13
T
B13
T
B13
Q15/Q19
T
B13
Q15/Q19
REQUIRED SETTINGS:BX: - Pool probe B13
REQUIRED SETTINGS:BX: -GlobaloutletprobeB10
REQUIRED SETTINGS:BX: -GlobaloutletsensorB10LP6600 (Device address): - 1 (cascade master)
OPTIONAL SETTINGSBX: - Cascade return probe B70
REQUIRED SETTINGS:OL6600 (Device address): - 2 to 16 (cascade slaves)
REQUIRED SETTINGS:QX: - Cascade pump Q25 BX: -GlobaloutletprobeB10LP6600 (Device address): - 1 (cascade master)
OPTIONAL SETTINGSBX: - Cascade return probe B70
REQUIRED SETTINGS:MG (LP6014, 6015): - Cascade return temperature control BX: -GlobaloutletprobeB10LP6600 (Device address): - 1 (cascade master)
REQUIRED SETTINGS:BX: - Pool probe B13
LP2080 (With supplementary solar): - Yes
REQUIRED SETTINGS:QX: - H1 Pump Q15 or - H3 Pump Q19 BX: - Pool probe B13 HX: - Pool enabling signal
REQUIRED SETTINGS:QX: - H1 Pump Q15 or - H3 Pump Q19 BX: - Pool probe B13 HX: - Pool enabling signal OL2080 (With supplementary solar): - Yes
POOL LOW-LOSS HEADER
- 134 -
Notes:
- 135 -
GB
Dear Customer,Ferroli S.p.A. would like to thank you for having chosen the Thermo EBM control panel. We trust that you have found all the informationyourequireinthismanual.For any further information, please contact your local authorised Ferroli service centre or the Ferroli service department.
PleasefindbelowasummaryoftherequirementsspecifiedbyEuropean Directive 2002/96/EC on the correct disposal of waste electrical and electronicequipment.Attheendoftheirworkinglife,wasteelectricalandelectronicequipmentCANNOT be disposed of as municipal waste.Suchequipmentcanbetakentolocalcouncilwastecollectionpoints,oralternativelyreturnedtothedealersthatprovidethisservice.Separatewastecollection prevents possible contamination of the environment and health risks, and allows materials to be recovered, bringing significant savings.Thecrossed-outwheeledbinsymbolshownisusedtoindicateseparatecollectionofwasteelectricalandelectronicequipment.
cod.
354
5315
/0 -
05/2
013
FERROLI S.p.A.via Ritonda 78/A ¬ 37047 San Bonifacio (VR) Italytel. +39 045 6139411 ¬ fax +39 045 6100933www.ferroli.it