pdh nms user manual

8/2/2019 PDH NMS User Manual

1/26

COMPACT PDH

NETWORK MANAGEMENT

User Manual


2/26

NMSUser Manual Page 2 of 26

1. Summary

NMS management system is used for managing PDH devices, it has network

management functions of enquiry alarm, performance and data configuration.

System request

Microsoft Windows TM NT/2000 series operating system

CPU of above Pentium TM II350

EMS memory of above 256MB

Display resolution of 1024768

Harddisk of above 10Gb spare capacity.

Software installation

NMS software installation is very simple, user only needs to find installation file

setup.exeand then install according to the clews.

2. Communication mode of network management

NMS network management system can manage multi units of PDH in multi-network.

2.1 Short-range management

PDH devices only offer one kind of network management port: serial port. If there is

only ETH in external environment, you can use virtual serial card. PDH can support 16

serial ports at most.

Serial Network Management method


3/26


Serial virtual ETH Network Management method

2.2 Remote management

Remote management means that NMS and device is not at the same place. NMS

manages PDH device through ETHcommon telephone line or DDN, such as followed

pictures:


4/26


Serial virtual ETH remote method

Serial remote method (centralized)

PDH (veneer) devices can use virtual serial card to extend serial port to device

through ETH


5/26


3. Basic operation

3.1 Login in the system

In default mode:Username is nullPassword is null

3.1.1 Main interface


6/26


3.1.2 Modify the Username


7/26


Enter the old Username, old Password and New Username

When follow picture is show, the Username modified successful.

3.1.3 Change the Password

Enter old Password, new Password and confirm Password

When follow picture is show, the Password change successful.

Use the new Username and Password to login the system.


8/26


3.2 Enter the main interface

3.3 Add subnet

When PDHis running for the first time, the navigating menu is blank. Click right key

of mouse, there will be pull-down menu of adding subnet, click Add Subnet, there will

be dialog box of adding subnet. If using keyboard, please press Add directly, there will

be followed dialog box. Note: you can add multi Subnet at the same time in NMS


9/26


Input subnet name directly in the dialog box, after clicking Add Subnet or press

ENTER, subnet will be added, and there will be dialog box of successful operation.

Use the Add Descriptionto describe the Subnet

Enter the description


10/26


Show the Network Property


11/26


3.4 Add network element

Select subnet which has been added, click right key of mouse, there will be pull-

down menu, and click the left key Add ne, there will be the interface of adding network

element, can add multiNe in one Subnet, that is,in one Subnet can add multi unitsof devices.

Then choose the device type and set the Ne Name in this interface, in this interface

will introduce the each device. After click the Add, the device view in NMS will be show.


12/26


3.5 Modify the Ne Name and Add Description

Modify the Ne name

Enter the new Ne Name

Then the Ne Name in NMS system will show


13/26


Add the description of Ne

Enter the description in the follow interface


14/26


Show the Ne Property

The view will show the information of Ne


15/26


3.6 Set the Link property of network element

Select network element which has been added, click Connect button in the view. ,

there will be pull-down menu, and choose which serials port is available in PC which

connect to the PDH through the console cable.

Then the system will show


16/26


When the PDH has connected the NMS system, the NMS system will show the state of

PDH.

The red LED in the panel means alarm.

The green LED in the panel means the state normal.

If there is any alarm in current PDH the Ne will show red


17/26


3.7 Network element-management

3.7 .1 Button in the NMS system

Save: save current settings into system, can use for setting of other devices, but need

Download to device, then setting can become effective.

Default: resume the default value configured by interface, at this time data hasnt been

sent down to device, through clicking Apply button, the default data can be sent down to

device.

Download: after data of network manager interface is configured, the configuring data

can be sent down to device through clicking Download button. After the device receives

the newest configuring data, they are stored to FLASH memorizer, and the working

mode of device is changed according to the newest configuring data.

Upload: Upload the newest network manager data which is stored in FLASH memorizer,

and show them through network manager interface.

Exit: exit the network management system.

3.7.2 Alarm information in the NMS system

Click the Local Alarm button can check the local alarm.


18/26


Click the Remote Alarm button can check the remote alarm.

3.7.3 Configure the device

Click the Config button, can configure the device, E1 and Ethernet port in the device.

In this interface, can set the Port Separation, Port-base VLAN, 802.1Q Tag VLAN,

Special Tagging.


19/26


3.7.3 .1 Special Tagging

Special Tagging is a private protocol. It will add a Tagging on the ETH packet which hadset the 802.1Q VLAN Tag. It can use add the Tag ID in the network. It can separate the4ETH port in the PDH base on Tag, but never effect the VLAN ID in the switch which

connect to the ETH port of PDH.

Like follow:

In the Special Tagging mode, the LAN1, LAN2, LAN3, LAN4 cant communication eachother, the each LAN, can set VLAN ID of 1-4095.In the NMS system, each PDH can be set to be 4 special Tagging at most, each ETHport is set to be 1 special Tagging.


20/26


3.7.3 .2 802.1Q tag VLAN

For example

As above picture,

User A1 only can communicate with User B1;




Add 5 records in VLAN table,

Set LAN 1 and WAN to belong to VLAN 1;


Set LAN 3 and WAN to belong to VLAN3;


Set LAN 1LAN 2LAN 3LAN 4 and WAN to belong to VLAN 5;


21/26


Set PVID of LAN 1 to be 1;



Set PVID of LAN 4 to be 4;Set PVID of WAN to be 5;


22/26


Port Separate is set to be DisableVLAN Mode is set to be IEEE 802.1q Tag VLAN.

At the same time need to set 802.1q Tagof WAN port to be VLAN TagInsertion,


23/26


Then click the Download

Click the OK, the configuration is downloaded to the device.


24/26


3.7. 4 Set the ETH Port

This interface is used for configuring attribute of each ETH port, including LAN port 1,

2, 3, 4 and one WAN port. LAN port shows 4 ETH ports offered by device, WAN port is

inner port of device, which connects remote device through optical port. Attribute

configuration of each ETH port includes 802.1Q tag Insertion and Removal, 802.3 X

Pause Enable and Disable, Port Forwarding Enable and Disable, Broadcast Storm

Protection Enable and Disable, Port Rate Limitation based on 32kbps (speed range is

0~100M), Speed and Duplex configuration of each ETH port.

802.1q Tag: Insert shows to insert Tag, when the data packet which is output from this

port has been with Tag, dont make any changes; if without Tag, insert VLAN ID which is

default in input port in the data packet.

Remove shows to remove Tag, when the data packet which is output from this

port has been with Tag, remove this Tag; if without Tag, dont make any changes.

802.3X: Enable shows to enable PAUSE of ETH port, Disable shows to disable

PAUSE of ETH port.

Port ForwardingEnable shows to enable Port Forwarding of ETH port, Disable

shows to disable Port Forwarding of ETH port.

Broadcast Storm ProtectionEnable shows to enable restrain function of ETH

Broadcast Storm, this port only allows 1% of ETH Broadcast packet to pass. Disable

shows to disable restrain function of ETH Broadcast Storm, this port forwards all ETH

Broadcast packet.

Rate Limitation: take 32kbps as step-size to adjust port rate, value rang is 0~3200.


25/26


Speed and Duplexcan be separately set to be AUTO, forced 100M full-duplex, forced

100M half-duplex, force 10M full-duplex, force 10M half-duplex.

3.7. 5 Set the E1 Channel

In E1 Channel view, can check the estate of each E1 of device, also can set loop estateof each E1 channel, can set each E1 channel as No Loop, Local Loop or RemoteLoop, which is easy to test and manage estate of each E1 channel.


26/26


3.8 Status of the device

This view mainly shows the working estate of current device.

3.9 Disconnect the device.

Use of buttonDisconnectis to disconnect RS232 connection of NMS system and device.

pdh nms user manual

Documents