1

QIQ FIX TM 2.3Mx1.5M GARDEN SHED

Assembly Instructions

Congratulations on purchasing your new QIQ FIXTM garden shed. Before commencing the assembly, we recommend that you read the instructions thoroughly. Your new shed comes with all the holes pre drilled to make for fast easy assembly. We recommend that you assemble the shed using a trestle table or sawhorses and planks. This will ensure that you are working off the ground and make it easier for you. Assembly is a two person job and should not be attempted in windy conditions. Step 1: Check all parts against the component list. Step 2: Assemble the rear wall panels. Step 3: Assemble the side wall panels. Step 4: Assemble the roof wall panels. Step 5: Assemble the front wall panels. Step 6: Assemble the front door. Step 7: Fit the panels together.

2

Concrete Slab: It is recommended that your new shed is secured to a concrete slab as per the specifications in this manual.

Concrete slab: Please ensure that your site is level. It is recommended that your slab is 100mm thick and you use builders plastic and F52 reinforcing mesh. We recommend that you make your slab 100mm bigger than the base dimensions of your shed. This will allow for a 50mm edge around your shed. We recommend that you slope the 50mm edges downward by 10mm so that rainwater can be drained away from your shed.

3

Tools Required:

4

Step 1：Check all parts against the component list Lay out all parts with number facing outwards and check off against parts list Picture Description Component Location Part

No. QTY BOX Check

Sheet Sheet 1900x770 rear wall

side wall 9S 6 BOX 2

Sheet Sheet 1900x770 rear wall 9M 1 BOX 2

Sheet Sheet 1169x770 -left roof 10L 2 BOX 1

Sheet Sheet 1169x770 -right roof 10R 2 BOX 1

Sheet Sheet 1900x735 -left front 11L 1 BOX 1

Sheet Sheet 1900x735 -right front 11R 1 BOX 1

Door Sheet Sheet 1845x770 door 5R 1 BOX 1

Channel channel 1843 door 24A 1 BOX 1

Channel channel 1843 door 24B 1 BOX 1

5

Channel channel 768 door 21C 2 BOX 2

Brace brace 1075 door U4 2 BOX 2

Channel channel 775 front 23A 1 BOX 2

Channel channel 1508 side wall roof 20A 4 BOX 1

Channel channel 1508

side wall 20B 2 BOX 1

Channel channel 1508 roof 20I 2 BOX 1

Channel channel 1124 rear wall 26C 1 BOX 1

Channel channel 1124 rear wall 26D 1 BOX 1

Channel channel 1124 rear wall 26H 1 BOX 1

Channel channel 1124 rear wall 26I 1 BOX 1

Channel channel 1124 front 26L 1 BOX 1

Channel channel 1124 front 26M 1 BOX 1

Channel channel 1124 front 26N 1 BOX 1

6

Channel channel 1124 front 26P 1 BOX 1

Channel channel 674 front 33A 1 BOX 2

Channel channel 674 front 33B 1 BOX 2

Channel channel 1098 rear wall 34R 1 BOX 1

Channel channel 1098

rear wall 34L 1 BOX 1

Channel channel 1458

side wall 31 2 BOX 1

Jamb jamb 1898 front 41A 1 BOX 1

Jamb jamb 1898 front 41B 1 BOX 1

Jamb jamb 775 front 42A 1 BOX 2

Lip lip 1172 roof 52 4 BOX 2

Gable cap Gable cap 1510 roof 90 1 BOX 2

Ridge beam Ridge beam 1510 zinc roof 91 1 BOX 1

7

Gable R/H Gable 1100 roof 63R 2 BOX 2

Gable L/H Gable 1100 roof 63L 2 BOX 2

Logo cap Logo cap roof 64 2 BOX 2

Roof brace Roof brace zinc roof 65 2 BOX 1

Channel connector

Channel connector 188mm

66 3 BOX 2

W 1 BOX 2

FITTINGS PACK

Picture Component QTY BOX Picture Component QTY BOX

Self-tapping screws(10mm) 260 BOX 2

Self-tapping screws(16mm) 22 BOX 2

φ4x10mm Rivet 12 BOX 2

φ3x10mm Rivet 40 BOX 2

Pad bolt 1 BOX 2 Keeper 1 BOX 2

8

Base bracket 9 BOX 2

5/16”x19mm Hexagonal bolt 9 BOX 2

5/16” Hexagonal nut 9 BOX 2

Mid wall brace bracket 4 BOX 2

Mid wall channel connector 1 BOX 2

Self tapper safety cover 25 BOX 2

Channel safety cover (L type) 1 BOX 2

Channel safety cover (R type) 1 BOX 2

Plastic stopper 4 BOX 2

Sleeve anchor bolt 9 BOX 2

Qty checking date: Qty checking personal badge number: Signature: In the unlikely event that you find you are missing a part, please contact Romak at 1800 702 660.

9

Shed Overview

10

Step 2: Assemble the rear wall panels. You will find it easier to assemble your shed using sawhorses with timber studs attached (timber needs to be the same length as the shed (2 M) or alternatively, a trestle table.

Place 2 x 9S and 9M the sheeting on your worktable and join together with the self-tapping screws per the diagram.

11

Now fit 26I, 26H top channel and 26C, 26D bottom channel to the sheeting by tapping it in ( diagram A ) or sliding it in. ( diagram B ) Be noted that the small lip of the channel is always facing out. This is to ensure that rainwater cannot build up inside your shed. Make sure 26I and 26H are used as top side channels.

12

Now fix 34R and 34L mid wall channels joint by mid wall channel connector to the sheeting by the self-tapping screws. Please note that the groove should face downwards. Fix other channels by the self-tapping screws. Apply 66 the channel connectors on top and bottom channels to enhance the strength. (Place a block under the shadowed area when screwing as a support and the screw with cross mark must not be fixed in this stage.)

13

Step 3: Assemble the side wall panels Place 2 x 9S the sheeting on your worktable and join together with the self-tapping screws per the diagram. Now fit 20B top channel and 20A bottom channel to the sheeting by tapping it in or sliding it in. Be noted that the small lip of the channel is always facing out. This is to ensure that rainwater cannot build up inside your shed. Make sure 20B are used as top side channels. Now fix 31 the mid wall channel to the sheeting by the self-tapping screws. Please note that the groove should face downwards.

14

Step 4: Assemble the roof panel. Place 10R and 10L the sheeting on your worktable and join together with the self-tapping screws per the diagram.

Fix 20I and 20A the channel by self-tapping screws per diagram. Please note that 20A are in the side with pre-punched holes on the sheeting.

15

Leave 4 corners unfixed in this stage. Repeat the same steps for the other roof.

16

Step 5: Assemble the front wall panels Fix 41A and 41B the jamb on 11L and 11R the sheeting by self-tapping screws.

Fix 26P, 26N top channels, 42A jamb, 26L, 26M, and 23A bottom channels by self-tapping screws. Enhance the top channels by applying 66 the channel connector.

17

Now fix 33A and 33B the mid wall channels to the sheeting by the self-tapping screws. Please note that the groove should face downwards.

18

Step 6: Assemble the front door. Place 5R the door sheet on the worktable. Fit 2 x 21C, 24A, 24B the channel and 2 x U4 the brace to the door and fix them with 3.0 x 10mm rivets. Please ensure that channel 21C has the smaller lip facing outwards.

19

20

21

Fit 5R the assembled door to the front wall panel per the diagram. Use riveter to fix the door into the pre-drilled holes. Fix the pad bolt (but NOT its keeper in this stage.) to the pre-drill holes by the self-tapping screws (or the rivets provided.) as well.

22

Step 7: Fit the panels together. Now fix the front, side, rear panels and 2 x 63R, 2 x 63L the gables together using the holes provided and then fix the pad bolt keeper by the self-tapping screws. (Use 16mm ones for the keeper. )

23

Join 90 gable cap and 91 ridge beam and fix them by 16mm self-tapping screws.

Slide in one side of the roof panel and note that the channel type 20I end is to the ridge beam.

24

Repeat the same step for the other assembled roof panel. Drill the holes through for roof brace by 3mm DRILL BIT. Then fix the roof brace per diagram. Join the sheeting and the gable by 52 the lip and then fix the 4 corners by 16mm self-tapping screws. (central screws marked cross NOT fixed in this stage. )

25

Put on 64 the Logo cap and then fix the roof panels by 16mm self-tapping screws per diagram.

26

Now fit the bolt down kit per the diagram. Strengthen your mid wall brace by applying 72 the mid wall brace bracket on each corner if necessary.

27

Apply channel safety cover L type on channel 33A and R type on channel 33B to prevent from getting cut by edge. Also apply the self-tapper covers on the screws fixed on the wall to prevent accidental injuries.

28

Door can be assembled on the opposite side as well. Align the door with the edge and make the holes by cordless drill. Take off the pin of hinge and reverse its direction before you assemble the door. Cover the previous pre-drilled holes by rivets if have cosmetic concern. Perform the same procedure for the padlock.

29

This Warranty against defects is given by: Romak Hardware Distributors Pty Ltd. Business Address: 177-187 Atlantic Drive, Keysborough VIC 3173. Ph: (03) 9795 6789 Fax: (03)9795 4567 Email: sales@romak.com.au New Zealand customers please contact: HARCO (Harkness & Young Ltd) Phone: 9 27 64071 Email: sales@harknessyoung.co.nz Details of Manufacturers Warranty This Product comes with a 15 year limited Structural Warranty (“the Warranty Period”) from the date of purchase. This Warranty also applies where there are missing or damaged parts identified in the parts list referred to in the instruction kit within the product packaging. Please ensure that you keep this warranty form in a safe place along with your proof of purchase. Product………………………………………………………… Place of purchase & Postcode Date of Purchase……../………../……… The benefits of this warranty are in addition to your rights under the Australian Consumer Law (ACL) and in particular, the guarantees implied under the ACL and any other rights and remedies of the consumer under a similar law in relation to the goods and services to which this warranty relates. Process of claiming Warranty To make a claim under the Warranty within the Warranty Period, you will need to contact The Manufacturer directly by phone or email: Claims Department contact number: 1800702660 Claims Department email: sales@romak.com.au You will be required to produce a Proof of purchase (or may need to be presented upon at The Manufacturer’s discretion) at the time of claim. The Manufacturer bears the cost of replacing the products or spare parts or repairing the products and reasonable direct expenses of claiming under this warranty: – Where replacement of parts, the Manufacture will bear the cost of sending the spare part and will endeavour to deliver to the customer’s nearest reseller within 10 working

30

days for the customer to pick up. At such time the customer may require to return the alleged faulty parts. – Where assessment is required in case of replacing or repairing The Product, The Manufacturer will appoint an assessor within 10 working days to identify should there be alleged defect. The Manufacturer will bear the costs of repairing by appointing a local tradesman. The Manufacturer may choose to replace The Product if the repair or the cost of repair is not feasible The Replacement Product will be available for collection to the nearest Reseller within 10 working days. The Customer will bear the cost of assembly if The Product is replaced. IMPORTANT 1. Manufacturer’s Disclosure This Warranty against defects shall not apply in the following situations: a) Where The Product is not assembled in accordance with the instructions provided in the product kit.

b) Where The Product is used to store corrosive materials such as fertilizer, chlorine and etc;

c) Where the damage to The Product is caused by storms. 2. Notes This Product is weatherproof to a certain extent; however driving windy rain may cause The Product to leak. Condensation may also occur in some weather conditions such as extreme heat or cold. The Product should only be used for storing items such as gardening equipment and should not be used for articles that may be prone to damage if they come into contact with moisture. We strongly recommend using a waterproof sealant in any required area of The Product in order to minimise the risk of water entering. 3. Major Defects Upon The Manufacturer being satisfied that the defect is a major defect, the purchase price may be refunded in lieu of providing a replacement products or repairing the products Our goods come with Guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. 01421