siemens relay configuration

8/12/2019 Siemens Relay Configuration

1/28

SIEMENS RELAY 7SA522 CONFIGURATION

Select the file and open new. The below display is appeared.

Now the new file is created for the project.

Enter name of

the project and

select ok.


2/28

Now select the folder right click and select Insert new device and Siprotec devices.

Now select the Type and Version of the relay and drag it to the folder.


3/28

Now feed the M!" n#mber which is available in the relay Settings$Set#p%

E&tra$M!" version and then press '(.


4/28

'nce M!" n#mber is done. The relay type and version is displayed.


5/28

Now select the relay type then right click and initiali)e device.

Select connection type *irect and comm#nication port then press '(.


6/28

Now the +, will comm#nicate with the relay and the following screen will appear.

Select -ES


7/28

Now enter the +SS/'0* 111111

Then press '(.


8/28

+ress '(.


9/28

Now right click on the type of the relay and select '+EN '"2E,T.

The above screen will appear and select *irect and press '(.


10/28

Now the relay is ready for changing the parameters.

*o#ble click on settings.


11/28

Select the *evice config#ration and do#ble click. !#nctional settings display will be

opened.


12/28

!or programming "inary inp#ts$"inary o#tp#ts$E*3s select Masking I$'

,onfig#ration and do#ble click.

Select the f#nction and

change it toEnable$*isable


13/28

Select the f#nction for which "inary o#tp#t has to config#red. 0ight click and select

ctive with voltage$ctive with o#t voltage.

Select

and

do#bleclick.


14/28

Select the f#nction for which the '#t p#t relay has to config#red4 then right click and

select atched$5nlatched.

Select and

do#ble click.


15/28

Select the f#nction for which the E* has to be config#red4 then right click and select

for atched$5n latched.

Select and do#ble click


16/28

,!, config#ration.

Then edit the information as per the system re6#irement.

0ight click here and select Insert

information.


17/28

'nce this is done. Then this signal has to be config#red for ,!, IN and '5T.

Same way do it for ,!, o#t.

Select the type of o#tp#t

re6#ired for ,!, and drag it .

Edit the label.

0ight click and select

,onfig#red.

*rag it to

this place.


18/28

Then close this window and go to main men# select ,!, and do#ble click.

0ight click and select

,onfig#red.


19/28

*o#ble click here.

*o#ble click on this.

Select the page here.


20/28

'nce the f#nction is selected4 Then yo# have to select the n#mber of inp#ts to be #sed

for the f#nction.

Select the f#nction.

*rag it here.


21/28

'nce No. of inp#ts are selected then press '(.

0ight click on

this and select

No. of inp#ts

Enter No. of

inp#ts to be

#sed.


22/28

Now select the page in which ogic gates are available. Then )oom it #ntil

Inp#t$'#tp#ts appear.

Now select the inp#t then right click and select the gro#p to be connected.

Select the page.

7oom it #ntil the

f#nction block inp#t

and o#tp#t appear.

0ight click on the

inp#t.

Select the gro#p

to be connected

to the inp#t.

Select here.


23/28


24/28

Select power system data8.

Select and

do#ble click.


25/28

Select settings 9ro#p and enter the relay settings.


26/28


27/28

fter changing the settings down load in to the relay.

Select to down

load settings.

Enter password

and press '(.


28/28

Select -ES to save

the settings.

siemens relay configuration

Documents