INS2074 - 3/11

TWO-HANDLE ROMAN TUB VALVEMODEL 86440 SERIES

TWO-HANDLE ROMAN TUB TRIMMODEL 86440 SERIES

7/8"1/2",13/16"

5/32”

HELPFUL TOOLSFor safety and ease of faucet replacement, Moen recommends the use of these helpful tools.

STOP HELP LINEPlease do not return this product to the store.If you need installation assistance, replacement parts or have questions regarding our warranty, please call our ProductConsultants at:

U.S.: 1-800-289-6636Monday - Friday 8:00 a.m. to 8:00 p.m. EST Saturday 9:00 a.m. to 5:30 p.m. EST Or e-mail us at: moenwebmail@moen.comBe sure to visit our website at www.moen.com

CAUTION — TIPS FOR REMOVAL OF OLD FAUCET: Always turn water supply OFF before removing existing faucetor disassembling the valve. Open faucet handle to relieve water pressure and ensure that complete water shut-off hasbeen accomplished.

Canada 1-800-465-6130Monday - Friday 7:30 a.m. to 5:00 p.m. EST Or e-mail us at: cantsd@moen.comBe sure to visit our website at www.moen.caWhen ordering parts, specify finishes.

Installation must be executed on finished installed surface.

Installation of any measurement other than 10 inches between hot and coldhandles will require cutting and soldering of the copper valve body.

MODEL 86440 SERIES

©2011 Moen Incorporated

INS2074 - 3/11

Moen Lifetime Limited Warranty

Moen products have been manufacturedunder the highest standards of qualityand workmanship. Moen warrants to theoriginal consumer purchaser for as longas the original consumer purchaser ownstheir home (the “Warranty Period” forhomeowners), that this faucet will beleak- and drip-free during normal useand all parts and finishes of this faucetwill be free from defects in material andmanufacturing workmanship. All otherpurchasers (including purchasers forindustrial, commercial and business use)are warranted for a period of 5 years fromthe original date of purchase (the“Warranty Period” for non-homeowners).

If this faucet should ever develop a leakor drip during the Warranty Period, Moenwill FREE OF CHARGE provide the partsnecessary to put the faucet back in goodworking condition and will replace FREEOF CHARGE any part or finish that provesdefective in material and manufacturingworkmanship, under normal installation,use and service. Replacement parts maybe obtained by calling 1-800-289-6636(Canada 1-800-465-6130), or by writing tothe address shown. Proof of purchase(original sales receipt) from the originalconsumer purchaser must accompany allwarranty claims. Defects or damagecaused by the use of other than genuineMoen parts is not covered by thiswarranty. This warranty is applicable onlyto faucets purchased after December,1995 and shall be effective from thedate of purchase as shown onpurchaser’s receipt.

Moen Incorporated25300 Al Moen DriveNorth Olmsted, Ohio 44070-8022U.S.A.

This warranty is extensive in that it coversreplacement of all defective parts andfinishes. However, damage due toinstallation error, product abuse, productmisuse, or use of cleaners containingabrasives, alcohol or other organicsolvents, whether performed by acontractor, service company, or yourself,are excluded from this warranty. Moenwill not be responsible for labor chargesand/or damage incurred in installation,repair or replacement, nor for anyindirect, incidental or consequentialdamages, losses, injury or costs of anynature relating to this faucet. Except asprovided by law, this warranty is in lieuof and excludes all other warranties,conditions and guarantees, whetherexpressed or implied, statutory orotherwise, including without restrictionthose of merchantability or of fitnessfor use.

Some states, provinces and nations donot allow the exclusion or limitation ofincidental or consequential damages, sothe above limitations or exclusions maynot apply to you. This warranty gives youspecific legal rights and you may alsohave other rights which vary from stateto state, province to province, nation tonation. Moen will advise you of theprocedure to follow in makingwarranty claims. Simply write to MoenIncorporated using the address below.Explain the defect and include proof ofpurchase and your name, address, areacode and telephone number.

INS2074 - 3/11

R

Q

14 16

1

L2

P

M

3

L5/32"

M

15

Q

MOEN

P/N 99

915

O

Apply grease (O) to spout shank. Assemblespout (Q) onto valve (K) while aligning rollpin (R) to slot in spout washer (E).

Using a set screw wrench (P), tighten setscrew (L) into spout securing spout tovalve (K). Insert plug button (M) into backof spout.

Assemble roll pin (R) onto hole onbottom of spout.

INS2074 - 3/11

13

Hold lever still and thread handleassemblies (N) on valve (K)

INS2074 - 3/11

99892

1512

X2

X2

131104131101

99915

MOEN

P/N 99

915

L

M

N

OR

S

Q

99892

5/32”P

A

B

C

Fx2

x2

I Jx2

K

H

D

E

140706

140707

Gx2 140708

140706

101039

101039

TWO-HANDLE ROMAN TUB VALVEMODEL 86440 SERIES

A. Shank coverB. Test plugC. Valve coversD. Spout shank clipE. Spout washerF. Valve upper mounting nutsG. Valve body locking washersH. Under deck spout washerI. Valve lower mounting nutsJ. Lower spout mounting nutK. Valve body

TWO-HANDLE ROMANTUB TRIMMODEL 86440 SERIES

L. Set screwM. Plug buttonN. Handle assemblyO. Grease packP. Set screw wrenchQ. SpoutR. Roll pinS. Stem extensions

Installation of any measurement otherthan 10 inches between hot and cold

handles will require cutting andsoldering of the copper valve body.

4H

KH

K

5

6E

D

1

2

5"

(127mm

)

5"

(127mm

) 6"M

AX

(152m

m)

1 7/8"

(23mm)

11/2"(38mm)

2

15/32"(12mm)

1"

3/ 16 "(5mm)

2

1

1 2

1

13

G

G

I

K

I

Drill the 7/8 inch spout shank hole nomore than 6 inches from the lip of the tub.Drill 1 1/2 inch holes for each of valves 5inches on center from spout shank.

Drill the roll pin hole with a 3/16 inch drill.Position the roll pin hole 15/32 inch from thefront center of the spout shank hole or 1 inchfrom the center of the spout shank hole.

Thread valve lower mounting nuts (I)on the valve body. Slide valve bodylocking washer (G) onto valve body.

Slide under deck mounting washer(H) onto spout shank aligning cut-outfor roll pin.

Slide spout washer (E) onto spoutshank aligning cut-out with roll pinhole. Insert spout shank clip (D) intogroove on spout shank.

Slide valve body (K) through drilledholes.

11

Rotate hot stem extensions (S) clockwiseagainst stop. Rotate cold stem extensions(S) counterclockwise against stop.

7

F

F

2

2

1

1

KF

8

J

Tighten to the deck. J

1

C

10B

BK

9

I

I

Tighten to the deck. I

Thread valve upper mounting nuts (F)onto valve body (K). Thread down nutsuntil they stop.

Tighten valve lower mounting nuts (I) tothe underside of the deck.

Tighten lower spout mounting nut (J) tothe underside of the deck.

Connect hot and cold water inlet linesto the bottom of the valve body (K).Thread test plug (B) into spout shank.Turn on water and test for leaks.

12

S

SN

NH

E

Place handle assembly (N) onto coldand hot stem extensions (S) withhandles pointing out.

INS2074 - 3/11

99892

1512

X2

X2

131104131101

99915

MOEN

P/N 99

915

L

M

N

OR

S

Q

99892

5/32”P

A

B

C

Fx2

x2

I Jx2

K

H

D

E

140706

140707

Gx2 140708

140706

101039

101039

TWO-HANDLE ROMAN TUB VALVEMODEL 86440 SERIES

A. Shank coverB. Test plugC. Valve coversD. Spout shank clipE. Spout washerF. Valve upper mounting nutsG. Valve body locking washersH. Under deck spout washerI. Valve lower mounting nutsJ. Lower spout mounting nutK. Valve body

TWO-HANDLE ROMANTUB TRIMMODEL 86440 SERIES

L. Set screwM. Plug buttonN. Handle assemblyO. Grease packP. Set screw wrenchQ. SpoutR. Roll pinS. Stem extensions

Installation of any measurement otherthan 10 inches between hot and cold

handles will require cutting andsoldering of the copper valve body.

4H

KH

K

5

6E

D

1

2

5"

(127mm

)

5"

(127mm

) 6"M

AX

(152m

m)

1 7/8"

(23mm)

11/2"(38mm)

2

15/32"(12mm)

1"

3/ 16 "(5mm)

2

1

1 2

1

13

G

G

I

K

I

Drill the 7/8 inch spout shank hole nomore than 6 inches from the lip of the tub.Drill 1 1/2 inch holes for each of valves 5inches on center from spout shank.

Drill the roll pin hole with a 3/16 inch drill.Position the roll pin hole 15/32 inch from thefront center of the spout shank hole or 1 inchfrom the center of the spout shank hole.

Thread valve lower mounting nuts (I)on the valve body. Slide valve bodylocking washer (G) onto valve body.

Slide under deck mounting washer(H) onto spout shank aligning cut-outfor roll pin.

Slide spout washer (E) onto spoutshank aligning cut-out with roll pinhole. Insert spout shank clip (D) intogroove on spout shank.

Slide valve body (K) through drilledholes.

11

Rotate hot stem extensions (S) clockwiseagainst stop. Rotate cold stem extensions(S) counterclockwise against stop.

7

F

F

2

2

1

1

KF

8

J

Tighten to the deck. J

1

C

10B

BK

9

I

I

Tighten to the deck. I

Thread valve upper mounting nuts (F)onto valve body (K). Thread down nutsuntil they stop.

Tighten valve lower mounting nuts (I) tothe underside of the deck.

Tighten lower spout mounting nut (J) tothe underside of the deck.

Connect hot and cold water inlet linesto the bottom of the valve body (K).Thread test plug (B) into spout shank.Turn on water and test for leaks.

12

S

SN

NH

E

Place handle assembly (N) onto coldand hot stem extensions (S) withhandles pointing out.

INS2074 - 3/11

99892

1512

X2

X2

131104131101

99915

MOEN

P/N 99

915

L

M

N

OR

S

Q

99892

5/32”P

A

B

C

Fx2

x2

I Jx2

K

H

D

E

140706

140707

Gx2 140708

140706

101039

101039

TWO-HANDLE ROMAN TUB VALVEMODEL 86440 SERIES

A. Shank coverB. Test plugC. Valve coversD. Spout shank clipE. Spout washerF. Valve upper mounting nutsG. Valve body locking washersH. Under deck spout washerI. Valve lower mounting nutsJ. Lower spout mounting nutK. Valve body

TWO-HANDLE ROMANTUB TRIMMODEL 86440 SERIES

L. Set screwM. Plug buttonN. Handle assemblyO. Grease packP. Set screw wrenchQ. SpoutR. Roll pinS. Stem extensions

Installation of any measurement otherthan 10 inches between hot and cold

handles will require cutting andsoldering of the copper valve body.

4H

KH

K

5

6E

D

1

2

5"

(127mm

)

5"

(127mm

) 6"M

AX

(152m

m)

1 7/8"

(23mm)

11/2"(38mm)

2

15/32"(12mm)

1"

3/ 16 "(5mm)

2

1

1 2

1

13

G

G

I

K

I

Drill the 7/8 inch spout shank hole nomore than 6 inches from the lip of the tub.Drill 1 1/2 inch holes for each of valves 5inches on center from spout shank.

Drill the roll pin hole with a 3/16 inch drill.Position the roll pin hole 15/32 inch from thefront center of the spout shank hole or 1 inchfrom the center of the spout shank hole.

Thread valve lower mounting nuts (I)on the valve body. Slide valve bodylocking washer (G) onto valve body.

Slide under deck mounting washer(H) onto spout shank aligning cut-outfor roll pin.

Slide spout washer (E) onto spoutshank aligning cut-out with roll pinhole. Insert spout shank clip (D) intogroove on spout shank.

Slide valve body (K) through drilledholes.

11

Rotate hot stem extensions (S) clockwiseagainst stop. Rotate cold stem extensions(S) counterclockwise against stop.

7

F

F

2

2

1

1

KF

8

J

Tighten to the deck. J

1

C

10B

BK

9

I

I

Tighten to the deck. I

Thread valve upper mounting nuts (F)onto valve body (K). Thread down nutsuntil they stop.

Tighten valve lower mounting nuts (I) tothe underside of the deck.

Tighten lower spout mounting nut (J) tothe underside of the deck.

Connect hot and cold water inlet linesto the bottom of the valve body (K).Thread test plug (B) into spout shank.Turn on water and test for leaks.

12

S

SN

NH

E

Place handle assembly (N) onto coldand hot stem extensions (S) withhandles pointing out.

INS2074 - 3/11

TWO-HANDLE ROMAN TUB VALVEMODEL 86440 SERIES

TWO-HANDLE ROMAN TUB TRIMMODEL 86440 SERIES

7/8"1/2",13/16"

5/32”

HELPFUL TOOLSFor safety and ease of faucet replacement, Moen recommends the use of these helpful tools.

STOP HELP LINEPlease do not return this product to the store.If you need installation assistance, replacement parts or have questions regarding our warranty, please call our ProductConsultants at:

U.S.: 1-800-289-6636Monday - Friday 8:00 a.m. to 8:00 p.m. EST Saturday 9:00 a.m. to 5:30 p.m. EST Or e-mail us at: moenwebmail@moen.comBe sure to visit our website at www.moen.com

CAUTION — TIPS FOR REMOVAL OF OLD FAUCET: Always turn water supply OFF before removing existing faucetor disassembling the valve. Open faucet handle to relieve water pressure and ensure that complete water shut-off hasbeen accomplished.

Canada 1-800-465-6130Monday - Friday 7:30 a.m. to 5:00 p.m. EST Or e-mail us at: cantsd@moen.comBe sure to visit our website at www.moen.caWhen ordering parts, specify finishes.

Installation must be executed on finished installed surface.

Installation of any measurement other than 10 inches between hot and coldhandles will require cutting and soldering of the copper valve body.

MODEL 86440 SERIES

©2011 Moen Incorporated

INS2074 - 3/11

Moen Lifetime Limited Warranty

Moen products have been manufacturedunder the highest standards of qualityand workmanship. Moen warrants to theoriginal consumer purchaser for as longas the original consumer purchaser ownstheir home (the “Warranty Period” forhomeowners), that this faucet will beleak- and drip-free during normal useand all parts and finishes of this faucetwill be free from defects in material andmanufacturing workmanship. All otherpurchasers (including purchasers forindustrial, commercial and business use)are warranted for a period of 5 years fromthe original date of purchase (the“Warranty Period” for non-homeowners).

If this faucet should ever develop a leakor drip during the Warranty Period, Moenwill FREE OF CHARGE provide the partsnecessary to put the faucet back in goodworking condition and will replace FREEOF CHARGE any part or finish that provesdefective in material and manufacturingworkmanship, under normal installation,use and service. Replacement parts maybe obtained by calling 1-800-289-6636(Canada 1-800-465-6130), or by writing tothe address shown. Proof of purchase(original sales receipt) from the originalconsumer purchaser must accompany allwarranty claims. Defects or damagecaused by the use of other than genuineMoen parts is not covered by thiswarranty. This warranty is applicable onlyto faucets purchased after December,1995 and shall be effective from thedate of purchase as shown onpurchaser’s receipt.

Moen Incorporated25300 Al Moen DriveNorth Olmsted, Ohio 44070-8022U.S.A.

This warranty is extensive in that it coversreplacement of all defective parts andfinishes. However, damage due toinstallation error, product abuse, productmisuse, or use of cleaners containingabrasives, alcohol or other organicsolvents, whether performed by acontractor, service company, or yourself,are excluded from this warranty. Moenwill not be responsible for labor chargesand/or damage incurred in installation,repair or replacement, nor for anyindirect, incidental or consequentialdamages, losses, injury or costs of anynature relating to this faucet. Except asprovided by law, this warranty is in lieuof and excludes all other warranties,conditions and guarantees, whetherexpressed or implied, statutory orotherwise, including without restrictionthose of merchantability or of fitnessfor use.

Some states, provinces and nations donot allow the exclusion or limitation ofincidental or consequential damages, sothe above limitations or exclusions maynot apply to you. This warranty gives youspecific legal rights and you may alsohave other rights which vary from stateto state, province to province, nation tonation. Moen will advise you of theprocedure to follow in makingwarranty claims. Simply write to MoenIncorporated using the address below.Explain the defect and include proof ofpurchase and your name, address, areacode and telephone number.

INS2074 - 3/11

R

Q

14 16

1

L2

P

M

3

L5/32"

M

15

Q

MOEN

P/N 99

915

O

Apply grease (O) to spout shank. Assemblespout (Q) onto valve (K) while aligning rollpin (R) to slot in spout washer (E).

Using a set screw wrench (P), tighten setscrew (L) into spout securing spout tovalve (K). Insert plug button (M) into backof spout.

Assemble roll pin (R) onto hole onbottom of spout.

INS2074 - 3/11

13

Hold lever still and thread handleassemblies (N) on valve (K)

INS2074 - 3/11

TWO-HANDLE ROMAN TUB VALVEMODEL 86440 SERIES

TWO-HANDLE ROMAN TUB TRIMMODEL 86440 SERIES

7/8"1/2",13/16"

5/32”

HELPFUL TOOLSFor safety and ease of faucet replacement, Moen recommends the use of these helpful tools.

STOP HELP LINEPlease do not return this product to the store.If you need installation assistance, replacement parts or have questions regarding our warranty, please call our ProductConsultants at:

U.S.: 1-800-289-6636Monday - Friday 8:00 a.m. to 8:00 p.m. EST Saturday 9:00 a.m. to 5:30 p.m. EST Or e-mail us at: moenwebmail@moen.comBe sure to visit our website at www.moen.com

CAUTION — TIPS FOR REMOVAL OF OLD FAUCET: Always turn water supply OFF before removing existing faucetor disassembling the valve. Open faucet handle to relieve water pressure and ensure that complete water shut-off hasbeen accomplished.

Canada 1-800-465-6130Monday - Friday 7:30 a.m. to 5:00 p.m. EST Or e-mail us at: cantsd@moen.comBe sure to visit our website at www.moen.caWhen ordering parts, specify finishes.

Installation must be executed on finished installed surface.

Installation of any measurement other than 10 inches between hot and coldhandles will require cutting and soldering of the copper valve body.

MODEL 86440 SERIES

©2011 Moen Incorporated

INS2074 - 3/11

Moen Lifetime Limited Warranty

Moen products have been manufacturedunder the highest standards of qualityand workmanship. Moen warrants to theoriginal consumer purchaser for as longas the original consumer purchaser ownstheir home (the “Warranty Period” forhomeowners), that this faucet will beleak- and drip-free during normal useand all parts and finishes of this faucetwill be free from defects in material andmanufacturing workmanship. All otherpurchasers (including purchasers forindustrial, commercial and business use)are warranted for a period of 5 years fromthe original date of purchase (the“Warranty Period” for non-homeowners).

If this faucet should ever develop a leakor drip during the Warranty Period, Moenwill FREE OF CHARGE provide the partsnecessary to put the faucet back in goodworking condition and will replace FREEOF CHARGE any part or finish that provesdefective in material and manufacturingworkmanship, under normal installation,use and service. Replacement parts maybe obtained by calling 1-800-289-6636(Canada 1-800-465-6130), or by writing tothe address shown. Proof of purchase(original sales receipt) from the originalconsumer purchaser must accompany allwarranty claims. Defects or damagecaused by the use of other than genuineMoen parts is not covered by thiswarranty. This warranty is applicable onlyto faucets purchased after December,1995 and shall be effective from thedate of purchase as shown onpurchaser’s receipt.

Moen Incorporated25300 Al Moen DriveNorth Olmsted, Ohio 44070-8022U.S.A.

This warranty is extensive in that it coversreplacement of all defective parts andfinishes. However, damage due toinstallation error, product abuse, productmisuse, or use of cleaners containingabrasives, alcohol or other organicsolvents, whether performed by acontractor, service company, or yourself,are excluded from this warranty. Moenwill not be responsible for labor chargesand/or damage incurred in installation,repair or replacement, nor for anyindirect, incidental or consequentialdamages, losses, injury or costs of anynature relating to this faucet. Except asprovided by law, this warranty is in lieuof and excludes all other warranties,conditions and guarantees, whetherexpressed or implied, statutory orotherwise, including without restrictionthose of merchantability or of fitnessfor use.

Some states, provinces and nations donot allow the exclusion or limitation ofincidental or consequential damages, sothe above limitations or exclusions maynot apply to you. This warranty gives youspecific legal rights and you may alsohave other rights which vary from stateto state, province to province, nation tonation. Moen will advise you of theprocedure to follow in makingwarranty claims. Simply write to MoenIncorporated using the address below.Explain the defect and include proof ofpurchase and your name, address, areacode and telephone number.

INS2074 - 3/11

R

Q

14 16

1

L2

P

M

3

L5/32"

M

15

Q

MOEN

P/N 99

915

O

Apply grease (O) to spout shank. Assemblespout (Q) onto valve (K) while aligning rollpin (R) to slot in spout washer (E).

Using a set screw wrench (P), tighten setscrew (L) into spout securing spout tovalve (K). Insert plug button (M) into backof spout.

Assemble roll pin (R) onto hole onbottom of spout.

INS2074 - 3/11

13

Hold lever still and thread handleassemblies (N) on valve (K)