Issue date: Valid until

16 February15 February

G Stones Technical Manager For and on behalf of the Head of

NMO I Stanton Avenue I Teddington I TW11 OJZ I United KingdomTel +44 (0) 20 8943 7272 I Fax +44 (0) 20 8943 7270 I WebNMO is part of the Regulatory Delivery directorate within the Department for Business,

EU-type examination certificate UK 2816 Revision

Issued by:

NMO Notified Body Number 0126

In accordance with the requirements of the Regulations 2016 (S.I. 2016 No. 1152) Council Directive 2014/31/EUto:

NCR Corporation 2651 Satellite Blvd Duluth Georgia 30096 USA

In respect of a Class III, NonNCR 7878-2000 scanner/scale and having the following characteristics:

Max = 15.000 kg Min = 0.100 kg e = 0.005 kg

The necessary data (principal characteristics, alterations, securing, functioningfor identification purposes and conditions (when applicable) are set out in the descriptive annex to this certificate.

This revision replaces previous versions of the certificate.

February 2017 February 2027

For and on behalf of the Head of Technical Services Stanton Avenue I Teddington I TW11 OJZ I United Kingdom

Tel +44 (0) 20 8943 7272 I Fax +44 (0) 20 8943 7270 I Web www.gov.uk/government/organisations/regulatoryNMO is part of the Regulatory Delivery directorate within the Department for Business, Energy & Industrial Strategy

type examination certificate Revision 8

Notified Body Number 0126

In accordance with the requirements of the Non-automatic Weighing Instruments (S.I. 2016 No. 1152) which implement, in the Un

2014/31/EU, this EU-type examination certificate has been issued

III, Non-Automatic Weighing Instruments designated the 2000 scanner/scale and having the following characteristics:

The necessary data (principal characteristics, alterations, securing, functioningpurposes and conditions (when applicable) are set out in the

descriptive annex to this certificate.

This revision replaces previous versions of the certificate.

UK 2816

0135

www.gov.uk/government/organisations/regulatory-delivery Industrial Strategy

automatic Weighing Instruments which implement, in the United Kingdom

certificate has been issued

Weighing Instruments designated the 2000 scanner/scale and having the following characteristics:

The necessary data (principal characteristics, alterations, securing, functioning etc) purposes and conditions (when applicable) are set out in the

2/15

Descriptive Annex

1 INTRODUCTION This instrument is an NCR 7878-2000 scanner/scale, Class III, mains operated, self-indicating, weight only, Non-Automatic Weighing Instrument (Figure 1).

The instrument may be used for direct sales to the public. 2 DESCRIPTION

2.1 Construction

2.1.1 Mechanical

Main features:

− Designed for flush-mounting in checkout surface or Self-Checkout Kiosk, having frame extensions to support the instrument in the checkout counter.

− Steel framework supporting four load cells, barcode scanner and electronics.

− NCR7825 remote display unit.

− NCR7878 barcode scanner.

− Interface for POS connection.

− Remote power supply module.

2.1.2 Scale module

The scale module, containing four load cells, is a Flintec type PBNS-30.

2.1.3 Power supply

The remote power supply unit is an AcBel model AP12AD13, and provides a regulated DC voltage of + 12 V to the weighing module and the barcode scanner. A powered USB interface can also be used to power the scale and barcode scanner.

2.1.4 Analogue circuitry

The analogue signals from the load cells are amplified, filtered and digitised.

2.1.5 Digital circuitry

Main features:

− Computational values from the EEPROM and weight data from the scale board are processed by a micro-computer (X-scale) for continuous weight display and, upon request, transmission of weight to a POS terminal or computer.

− The EEPROM contains configuration data including span, zero and linearity settings.

2.1.6 Display

The weight display is provided by either a dual or single NCR7825 remote display (Figure 2). The display consists of an LCD panel with seven segments, each 9.5 mm high. The two

3/15

digits furthest to the right are used to show the unit of weight.

2.2 Operation

Main features:

− Upon power up, diagnostic routines are run to check the correct functioning of the instrument.

− Before display or transmission to the interface, the weight data is checked for stability.

− Zero tracking operates at zero indicated weight, and is only applied over the range of 4% of capacity.

3 TECHNICAL DATA

3.1 Rated operating conditions

The supply to the remote power supply module can be 90-240 V AC, 50/60 Hz.

The temperature range for the instruments is 0 °C / +40 °C.

3.2 Software

The firmware identification shall be as follows.

The firmware identification information can be dictated by the device by scanning the following bar codes in the order they are presented in this certificate. These bar codes are also available in the instrument user manual.

Product Class

Firmware

Revision

# Product Class

Firmware

Revision

# Product Class

Firmware

Revision

#

497-0453374 497-0213087 497-0477890

497-0454779 497-0459023 497-0479878

497-0455089 497-0459309 497-0503771

497-0455729 497-0459425 497-0508539

497-0459977 497-0459952

497-0461765 497-0461146

497-0464756 497-0465808

497-0465525 497-0466519

497-0466566 497-0468219

497-0466908 497-0473917

497-0467514 497-0475101

497-0469068 497-0475534

497-0472618 497-0477721

497-0473670 497-0478672

497-0475233 497-0501350

497-0477547 497-0502963

497-0501349 497-0503772

497-0502962 497-0506155

497-0503657 497-0508540

497-0504250 497-0512808

497-0506154

497-0508538

7878-XXXX-XXX 7874-XXXX-XXXX 7812-XXXX-XXXX

4/15

The firmware is fully embedded on the instrument and downloads of firmware are only possible with the use of an encrypted NCR flash drive. Each time the firmware is updated the non-resettable “FLS” event counter will increment by one. Firmware will be stored with a date stamp. The “FLS” event counter and date stamp can be displayed by pressing and holding the Zero button.

5/15

3.3 Documentation and drawings

The instrument is fully described in the technical file held at NMO.

4 PERIPHERAL DEVICES AND INTERFACES

4.1 Peripheral devices

There are no peripheral devices approved under this certificate.

4.1 Interfaces

The instrument may have the following interface types:

− IBM 485

− USB/USB power

− RS232

− Display

− Scanner

− ICL MDL (Interlock)

4.3 Electronic Point of Sale (EPOS) The instruments may be connected to an Electronic Point of Sale (EPOS) if the following conditions are met:

− The EPOS have a Parts (Test) Certificate issued by a Notified Body appointed to certify instruments according to paragraph 1 of Annex II of the Directive 2014/31/EU;

− If the EPOS have a preset tare function, they shall carry out this function autonomously and this function shall be in conformity with EN45501;

− The connection shall be made in such a way that the weight indication, the unit price and price-to-pay are positioned adjacent to each other.

5 APPROVAL CONDITIONS

This certificate is issued subject to the following conditions:

5.1 Inscriptions

5.1.1 The instrument shall bear the following inscriptions on or near the display:

− Max

− Min

− e = 5.1.2 The instrument shall bear the following inscriptions:

− CE marking

− Supplementary metrology marking

− Identification number of the notified body

− Number of the EU-type examination certificate

− Manufacturer’s name, registered trade name or registered trade mark and postal address

6/15

− Accuracy class

− Type, batch or serial number

and, when applicable:

− for instruments consisting of separate but associated units: identification mark on each unit;

− scale interval if it is different from e, in the form d = K;

− maximum additive tare effect, in the form T = + K;

− maximum subtractive tare effect if it is different from Max, in the form T = – K;

− tare interval if it is different from d, in the form dT = K;

− maximum safe load if it is different from Max, in the form Lim K;

− the special temperature limits, in the form K oC/K oC;

− ratio between load receptor and load.

The markings and inscriptions shall fulfil the requirements of Article 6, Article 16, Article 17 and Point 1 of Annex III in Directive 2014/31/EU.

6 LOCATION OF SEALS AND VERIFICATION MARKS

6.1 A wire and seal or a paper seal is used to secure the cover protecting the calibration switch, which is housed in a compartment underneath the load receptor (Figure 3).

Components that may not be dismantled or adjusted by the user will be secured by either a wire and seal or a tamper-evident label and securing mark. The securing mark may be either:

− a mark of the manufacturer and/or manufacturer’s representative, or

− an official mark of a verification officer.

6.2 The CE marking is located on the data plate, which is on the right-front support flange (Figure 4).

6.3 The value of the “FLS” counter described in section 3.2 must be marked on a tamper-evident label on or near the rating plate.

7 ALTERNATIVES

7.1 Having an extended weighing receptor attachment. An additional vertical weighing receptor constructed from stainless steel is attached to the sub-platter. The vertical weighing receptor is part of the “live” weight receptor, and enables oversized goods to be weighed (Figure 5).

7.2 Having a Sensormatic EAS security tag deactivation antenna fitted beneath the load receptor scanner window (Figure 6).

7.3 Having the data plate placed on the scale module, and visible through the transparent plastic debris shield (Figure 7).

7.4 An alternative primary live weight indication may be provided on any NCR CE marked Point of Sale (POS) touch screen display, any NCR CE marked Self-Check Out (SCO) or any NCR CE marked Customer’s Information Display (CID) which is a CRT or Flat Screen Monitor with weight information conforming to the minimum numeric height requirement of 9.5 mm and the “kg” unit identification. The Max, Min and e = information must be shown near the weight indication.

7/15

7.5 Having the 7878-2000 model which is identical to 7874-5000 except that the weigh plate is smaller in size than the 7878 weigh plate. The model 7874-5000 can be mounted into an optional stainless steel mounting bracket and has a 2.5 cm longer extended weigh plate (Figures 8 and 9).

7.6 Having the NCR 7878-2XXX series which has an alternative design similar to that for 7874-5XXX series. The instrument has a composite material for the base (bottom bucket) instead of cast aluminum. There are no metrological differences between the two design types.

7.7 Having the NCR 7874-5XXX series which features an optional weigh plate made from stainless steel. This redesign weigh plate comprises of two separate sheets covering the weighing platform instead of two winged stainless steel sheets.

7.8 Having the NCR 7874-5XXX series which features an optional produce guard located adjacent to the weigh plate. The produce guard will be secured by four small screws. The dimensions are as follows; length 27.93 cm, width 1.62 cm and height 1.33 cm.

7.9 Having the NCR 7812-5XXX series, which is technically similar to model series 7878-2000 except that the housing is smaller in size (29.5 cm wide x 27.1 cm length x 13.9 cm high) and the operational buttons are located horizontally instead of vertically. A NCR7884 barcode scanner can be connected to the NCR 7812-5XXX series (Figure 12).

7.10 Having a modified Scale Digital Board as per drawing 497-0464801. 8 ILLUSTRATIONS

Figure 1 NCR7878-2000 scanner/scale Figure 2 NCR7825 dual and single head remote display Figure 3 Location of seal Figure 4 Location of data plate Figure 5 Extended weighing receptor attachment Figure 6 With Sensormatic EAS security tag deactivation antenna Figure 7 Alternative location of data plate Figure 8 Model 7874-5000 with optional mounting bracket and extended weigh plate Figure 9 Side by side, 7874-5000 standard and optional extended weigh plates Figure 10 7874-5XXX optional weigh plate Figure 11 7874-5XXX optional produce guard Figure 12 7812-5XXX series Figure 13 Example data plate (post April 2016)

8/15

CERTIFICATE HISTORY

ISSUE NO. DATE DESCRIPTION

UK 2816 21 February 2007 Type approval first issued.

UK 2816 Revision 1 02 June 2008 Creation of Section 7.5, new models added 7874-5000.

UK 2816 Revision 2 07 July 2009 Creation of Section 7.6, alternative design for 7878-2XXX series.

UK 2816 Revision 3 12 July 2010 Creation of Section 7.7, optional design for 7874-5XXX series.

UK 2816 Revision 4 11 February 2011 Creation of Section 7.8, produce guard

for 7874-5XXX series.

UK 2816 Revision 5 14 November 2013 Creation of Section 7.9, for 7874-5XXX series. Section 4.2.1 modified (addition of text in last 2 bullet points).

UK 2816 Revision 6 09 March 2015 Renumbering of sections 7.4 to section 7.9. The following text added to section 7.4 “any NCR CE marked Self-Check Out (SCO)”.

UK 2816 Revision 7 25 February 2016 Section 4.2 USB power interface added.

Section 7.10 added.

UK 2816 Revision 8 16 February 2017 Certificate renewed for a further 10 years. Added “or Self-Checkout Kiosk” in section 2.1.1. Added the temperature range in section 3.1. Sections 3.2, 3.3 and 6.3 added. Figure 13 added. Updated references from 2009/23/EC to 2014/31/EU. Updated section 5.1 in accordance with 2014/31/EU.

9/15

Figure 1 NCR7878-2000 scanner/scale

Figure 2 NCR7825 dual and single head remote display

10/15

Figure 3 Location of seal

Figure 4 Location of data plate

11/15

Figure 5 Extended weighing receptor attachment

Figure 6 With Sensormatic EAS security tag deactivation antenna

12/15

Figure 7 Alternative location of data plate

Figure 8 Model 7874-5000 with optional mounting bracket and extended weigh plate

13/15

Figure 9 Side by side, 7874-5000 standard and optional extended weigh plates

Figure 10 Side by side, 7874-5XXX optional weigh plate

14/15

Figure 11 7874-5XXX optional produce guard

Figure 12 7812-5XXX series

15/15

Figure 13 Example data plate (post April 2016)

Crown copyright 2017 NMO Regulatory Delivery directorate Department for Business, Energy & Industrial Strategy This material may be freely reproduced except for sale