WIRED BEADED FLOWER BANGLEWIRE & JEWELRY MAKING TUTORIAL SERIES T173

COPYRIGHT

Copyrights DIY Beading Club 2013

Published By DIY Beading Club

INTRODUCTION

Learn how to make a flower that would never wither.Use it as a brooch, pendant and also perfect as a bangle!

With this tutorial, you'll learn simple wirework technique on how to create a flower and use it as bangle.

Exploring your creativity and skill, you can give each flower a different lookand create lots of variations for a bangle design.

The tutorial is catered for beginners or anyone who loves to learn this basic wirework techniques.  It has in-depth instructions and ultra-clear, close-up photos at each

step. Additionally, you can ask me question you have on the tutorial. No more getting stuck and frustrated on a confusing or just plain inaccurate pattern.

MATERIALS AND TOOLS NEEDED:

Materials Neededsome 11/0 seed beadsapproximately 50cm x 1mm copper wireapproximately 80cm x 0.3mm copper wire0.7mm copper wire 7 teardrop beads approximately 1.5cm in length1 x 6mm in diameter round bead

Tools NeededWire cutterRound nose pliersFlat nose pliersBracelet Mandrel or any rounded object

STEP BY STEP INSTRUCTIONS

Step 1: First layer of flowerPrepare a roll of copper and start inserting seed beads. You need to have about 80cm of copper wire threaded with seed beads. Adjust the length if you like smaller or bigger flower. When you have enough seed beads you can tie a loose knot at the beginner of the wire to prevent the seed beads from falling off the copper wire.

 

At the other side, leave about 7cm of wire without seed beads. Cut off the wire and tie a small loose knot as well. The knot will prevent the seed beads from dropping out from the wire. 

 

Step 2: Now, weave the wire around your 2 fingers and from a figure 8 till the end of the wire.

Place the start of the seeded wire in between the index and middle fingers. Bring the seeded wire to the back of the finger and bring it back the front of the middle finger.  

 

Bring the seeded wire to the back of your middle finger and bring it up to the front by passing through the gap between your index and middle fingers. 

 

Continue the same figure 8 weaving pattern until you reach the end of seeded wire. 

 

Step 3: As we are going to tie up the wire and the joint between the 2 fingers, remove the excess seed beads that are beyond the middle point.

 

Now, go back to the starting point and grab and bend the wire (where you left it without seed beads earlier) and bring it the to the back through the gap between the 2 fingers. Then bring it to the right from the back and to the left (front) to wrap the joint. 

 

Wrap around the joint a few times to tighten the flower.

Step 4: Untie the knot on the other end of the wire and remove the extra seed beads.

 

Use the remaining wire to wrap around the joint.

 

 

Now twist the two excess wires a few times to secure the joint.

 

Step 5: Spread out the petals to make into a flower.

 

Step 6: Second layer of flower Now, let's begin with a second layer of petals.

Cut approximately 6cm x 0.3mm copper wire and insert 7 pieces of teardrop beads.

 Join the wires together and cross one end of the wire to the first teardrop bead. 

 

Bend the wire towards the center.

 

Step 7: Take a 6mm round bead and thread into one of the wires. 

 

Bring this wire to the back of the petal and to the other end of the wire and wrap it 1 time onto the wire in between the teardrop beads to secure the position. 

 

Step 8: Bring up your first layer of flower and attached the second layer of flower by inserting the extended wires into the petals and bring them to the back of the petals.

Twist the wire at the back to tighten the petals. Do not cut off the excess wire, yet. Set aside.

Step 9: The banglePrepare 2 pcs 1mm x 22cm copper wire and create a loop on each end. Set aside. This will be your bangle frame.

 

Step 10:Now we are going to prepare branches that will be inserted into the frame of the bangle. 

Cut 3cm of 0.7mm copper wire.

Bend the tip of the wire and grip with your round nose pliers make a loop.

 

 

Step 11: Slide in some 11/0 seed beads, but leave a space for you to make another loop.

 

Prepare approximately 50 pieces of such branches. Number of branches required will depend on the length of your bangle. You can add on more later on. 

Tips:Ensure you measure the length of copper wires to make these branches accurately. For this tutorial, I am using 3cm as the length to make a bangle. I am using 0.5cm of wire to make each loop. So for 2 loops, you will make use of 1cm of copper wire and that leave about 2cm as the width for the bangle. By measuring accurately, it will ensure you have consistent width throughout the making of the bangle. 

Step 12:Now insert these branches into the bangle frame. Insert as many until you are close the the center part of the bangle. 

 

To attach the wired flower onto the frame, you can cut approximately 10cm of 0.3mm wire and wrap it around the upper frame. 

 

Secure your wired flower with the wire by wrapping it a few times. Repeat the same process for the bottom frame and cut off excess wires. You can also use the remaining wire from the wired flower to tie it against the frame. 

Then fill the rest of the bangle frame with beaded branches.

Step 13:Shape your bangle with a mandrel or any rounded object about the size of your wrist.

 

Then make a loop on the end.

 

Attach a jump onto the loops, followed by your clasp.

You now have your bangle with a wired flower as it's focal piece.

 

CONTACT US

I hope you have enjoyed making the jewelry. If you have any query or feedback for the tutorial, please contact us at diyjewelryclub@gmail.com.

SPECIAL OFFER FOR READERS

We are giving special discount to our existing readers who purchase any jewelry making membership package at DIY Beading Club. Just use this coupon code C8E005B8 to claim for 10% discount on any of our membership package at DIY Beading Club

ABOUT THE AUTHOR

Started as a hobby, I have then addicted into sharing my knowledge through tutorial writing. I publish my knowledge and research through my websites. I also work with other jewelry artists to develop tutorials and publish their works. I hope you will browse through all our creations and hope you will like them.

Do join me at

Browse our monthly lessons plan at www.diybeadingclub.com: