anemometer installation instructions rev03updated05!19!2011
TRANSCRIPT
-
8/3/2019 Anemometer Installation Instructions Rev03updated05!19!2011
1/6
`
WindTronics Headquarters
380 W. Western Ave. Suite 301
Muskegon, MI, 49440
Customer Service and Tech Support: 877-946-3898
www.windtronics.com
Anemometer Installation Instructions(Model Number: WT6KASSY013)
Revision 3.0 19May11
-
8/3/2019 Anemometer Installation Instructions Rev03updated05!19!2011
2/6
`
2Anemometer Installation Rev 3.0 19May11
WindTronics Headquarters
380 W. Western Ave. Suite 301
Muskegon, MI, 49440
Customer Service and Tech Support: 877-946-3898
www.windtronics.com
1) Anemometer Installation
Hardware Required
a. Anemometer Kit
b. Cord Grip (in Anemometer Kit Box)
c. J-Box
d. Wrench (not included)
e. Small Phillips (X) Screwdriver (not included)
f. Small Adjustable Wrench (not included)
2) Installation Steps
Figure 1Knock Out Plug
2.1)Remove from the j-box the knock oplug shown in Figure 1.
2.2)Cut the anemometer wire to requiredlength and strip wires as in Figure 2.
Remove the lock nut from the cord griwhich can be found in the anemometekit box. Leave on the sealing o-ringshown in Figure 2. Loosen the cord gand push it onto the anemometer poleas shown in Figure 2.
Figure 2Cord Grip on Anemometer Pole
Slip Ring
-
8/3/2019 Anemometer Installation Instructions Rev03updated05!19!2011
3/6
`
3Anemometer Installation Rev 3.0 19May11
WindTronics Headquarters
380 W. Western Ave. Suite 301
Muskegon, MI, 49440
Customer Service and Tech Support: 877-946-3898
www.windtronics.com
Figure 3Anemometer Mounting Location on J-Box
2.3)Insert the anemometer pole into the
j-box as shown in Figure 3. Make surewind vane is upwards. Thread thelocknut onto the cord grip from inside th
j-box.
Figure 4Anemometer Mounting Hardware in Kit
2.4)From the anemometer hardware baginside the kit box, find the screw, flatwasher, external tooth lock washer andnut shown in Figure 4.
Wind Vane
-
8/3/2019 Anemometer Installation Instructions Rev03updated05!19!2011
4/6
`
4Anemometer Installation Rev 3.0 19May11
WindTronics Headquarters
380 W. Western Ave. Suite 301
Muskegon, MI, 49440
Customer Service and Tech Support: 877-946-3898
www.windtronics.com
Clearance Hole2.5)Once inside the j-box, turn theanemometer pole so you can see thedrilled hole. Put the flat washer onto thescrew and thread it through the hole asshown in Figure 5.
2.6)Loosely thread on the external tooth lockwasher and nut as shown in Figure 5.
2.7)Rotate the pole and position the screwover the clearance hole in the backplate.
Figure 5Anemometer Mounting Location
Clearance Hole
External ToothLock Washer
Flat Washer
Nut
2.8)Using the wrench, hold the nut inplace as in Figure 6. Using a smallPhillips screwdriver, turn the screwclockwise until it is all the way down intothe clearance hole in the back plate andthe nut tightens up against the pole.
2.9)Tighten the locknut against the j-box to
secure the cord grip.
Figure 6Anemometer Back Plate Connection
Locknut
-
8/3/2019 Anemometer Installation Instructions Rev03updated05!19!2011
5/6
`
5Anemometer Installation Rev 3.0 19May11
WindTronics Headquarters
380 W. Western Ave. Suite 301
Muskegon, MI, 49440
Customer Service and Tech Support: 877-946-3898
www.windtronics.com
Figure 8Anemometer Wire Connections
2.11)Connect the anemometer wires asshown in Figure 8. Bottom connectionsare for wiring to the turbine controller.
Figure 7Cord Grip Tightening
2.10)Tighten the cord grip from the outside asin Figure 7 until the anemometer pole issecure.
-
8/3/2019 Anemometer Installation Instructions Rev03updated05!19!2011
6/6
`
WindTronics Headquarters
380 W. Western Ave. Suite 301
Muskegon, MI, 49440
Customer Service and Tech Support: 877-946-3898
www.windtronics.com
AII-Rev3.0-19May11