User instructionsEN

CDI 1012

DISHWASHER

3

CONTENTS

Safety adviceSetting up, installationTechnical notes for cabinet fittersWater softener unitLoading the dishesInformation for test laboratoriesHalf load washingLoading the detergent and rinse aidCleaning the filtersSome practical hintsRoutine cleaning and maintenanceDescription of the controlsTechnical dataOperating the programmes and special functionsProgramme selection Identifying minor faults

pag. 4 pag. 5pag. 8pag. 12pag. 14pag. 16pag. 17pag. 18pag. 20pag. 21pag. 22pag. 23pag. 23pag. 24pag. 26pag. 28

Please read the instructions in this booklet carefully because they contain importantinformation on how to install, use and maintain your dishwasher safely as well ascontaining useful tips on how to make the most of it.

Keep this booklet safe for future reference.

Fig. A

3 2

1

4

5

Congratulations!

Thank you for choosing a Candyappliance; quality dishwashers whichguarantee high performance andreliability.Candy manufacture a vast rangeof domestic appliances: washingmachines, washer/dryers, cookers,microwave ovens, ovens and hobs,refrigerators and freezers.Ask your dealer for the catalogue withthe complete range of Candy products.Please read this booklet carefully asit provides important informationregarding the safe installation, use,and maintenance of the machine,together with some useful advice onhow to achieve the best results fromyour dishwasher.For future reference please keep thisinstruction booklet in a safe place.

CUSTOMER SERVICE AND GUARANTEEYour new appliance is fully guaranteedby the manufacturer for 12 monthsagainst electrical/mechanical break-down excluding:

A. Any faults which occur due to badinstallation or misuse of the machine.

B. Any faults which occur due to repairof, or interference with, the machineby any person not authorised by themanufacturer to carry out service.

C. Any faults which occur due toany parts which are fitted to themachine which are not the originalmanufacturers parts.

D. Any faults arising from non-domesticuse or unusual or abnormal use ofthe machine.

E. Any faults arising from operation atincorrect voltage.

F. Any faults arising from incorrectoperation of the machine.The guarantee applies to Gt Britainand Northern Ireland only, and is anaddition to your statutory rights.

AFTER SALES SERVICE

For service and repairs call your local engineer on our national telephone number:

GIAS Service Tel: 08705 400 600

Support Service (Eire 018301 666)

2

5

INSTALLATION(Technical notes)

IMPORTANTWhen the appliance is located on acarpet floor, attention must be paid toensure that there is no obstruction tothe bottom vents.

Make sure that the plug on theappliance remains accessible afterinstallation.

Electrical connection

Plug your dishwasher into the powersocket.

If the plug we supply does not fit :

■ CUT IT OFF AND DESTROY IT!

You can't use it on other appliances, andthe exposed wires could be dangerous ifanyone plugged it in.

■ Fit a suitable plug, as follows:

WARNING!THIS APPLIANCE MUST BE EARTHED.

Fuses and plugs

This appliance should be used only on asocket with a minimum rating of 13 Amp.

Our ready-fitted plug is already equippedwith a 13 amp fuse which is BS 1362 ASTAapproved.

Any replacement should be exactly the same.

If the fuse cover is lost, do not use the pluguntil it is replaced.

A correct replacement fuse cover (obtaina-ble from your dealer or Electricity board)must be the same colour as shown ornamed on the insert on the base of theplug.

Manufacturer declines all responsibilityfor any damage due to non-earthing ofthe machine.

This appliance complies withDirectives 89/336/EEC, 73/23/EECand following changes.

Green andyellow wire

Marked with the letter E,

OR marked with the Earthsymbol,

OR coloured green,

OR coloured green andyellow.

Blue wire

Brown wire

Marked N,

OR coloured black.

Marked L,

OR coloured red.

Connect to the terminal in the plug

4

SAFETY INSTRUCTIONS

There are certain basic safety ruleswhich are valid for any domesticappliance.

Installation

■ Make sure that the plug fitted to themachine is compatible with the powersupply socket. If it is not, get a suitablyqualified person to fit the correct type,and to make sure that the cables to themains socket are able to cope with thepower rating of the appliance.

■ Ensure that the dishwasher does notcrush power cables.

■ In general it is not advisable to useadaptors, multiple plugs and/or extensioncables.

■ Should it be necessary to replace thesupply cord, call the After Sales ServiceCentre.

Safety

■ Never touch the appliance when yourhands or feet are wet or damp.

■ Do not use when your feet are bare.

■ Do not remove the plug from the mainssupply socket by pulling the mains cableor the machine itself.

■ Do not leave the appliance exposed tothe elements (rain, sun etc).

■ Do not let children (or others incapableof operating it) use the machine withoutsupervision.

■ Water left in the machine or on thedishes at the end of the wash programmeshould not be swallowed.

■ The door should not be left in the openposition since this could present a potentialhazard ( es. tripping ).

■ Leaning or sitting on the open door ofthe dishwasher could cause it to tip over.

WARNING !Knives and other utensils with sharppoints must be loaded in the basketwith their points down or placed in ahorizontal position.

Daily use

■ This appliance is be designed for domesticuse only.

■ The dishwasher is designed for normalkitchen utensils.Objects that have been contamined bypetrol, paint, traces of steel or iron,corrosive chemicals, acids or alkalismust not be washed in the dishwasher.

■ If there is a water softening device installedin the home there is no need to addsalt to the water softener fitted in thedishwasher.

■ Cutlery is washed best if it is placed inthe basket with the handles downwards.

■ If the appliance breaks down or stopsworking properly, switch it off, turn off thewater supply and do not tamper with it.Repair work should only be carried outby an approved service agent and onlygenuine spare parts should be fitted. Anyfailure to follow the above advice mayhave serious consequences for the safetyof the appliance.

Disposal

■ The dishwasher has been made frommaterials which can be recycled so that itcan be disposed of in an environmentallyfriendly way.

■ If you wish to dispose of an old dishwasherbe careful to remove the door toeliminate the risk of children becomingtrapped inside it.

7

Connecting the outlet hose

■ The outlet hose should disharge into astandpipe, making sure that there are nokinks (fig. 4) .

■ The standpipe must be at least 40 cmabove floor level and it must have aninternal diameter of at least 4 cm.

■ It is advisable to fit an anti-odour air trap(fig. 4X) .

■ If necessary the outlet hose can beextended up to 2,5 m, provided that it iskept at a maximum height of 85 cmabove floor level. The extension pipe isavailable from the After Sales ServiceCentre.

■ The hose can be hooked over the side ofthe sink, but it must not be immersed inwater, in order to prevent water frombeing syphoned back to the machinewhen this is in operation (fig. 4Y) .

■ When installing the appliance under aworktop the hose pipe clamp must beattached to the wall in the highest possibleposition under the worktop (fig. 4Z) .

■ Check that there are no kinks in the inletand outlet hoses.

4

Opening the door

Put your hand into the recess and pull. If the machine comes open while it is working,an electrical safety device automaticallyswitches everything off.

IMPORTANTFor the machine to work properly,the door should not be opened whileit is in operation.

Closing the door

Place the baskets in the machine. Make sure that both the spray arms arefree to rotate and are not obstructed bycutlery, crockery or pans. Close the door,pressing on it to make sure it is firmly shut.

Water connection

IMPORTANTThe appliance must be connected tothe water mains using new hose-sets.The old hose-sets should not be reused.

■ The inlet and drain hoses can be directedto left or right.

IMPORTANTThe dishwasher can be connected toeither cold or hot water, as long as itis no hotter than 60 °C.

■ Water pressure must be between0,08 MPa and 0,8 MPa. If the pressure isbelow the minimum consult our servicedepartment for advice.

■ The inlet hose must be connected to atap so that the water supply can be cutoff when the machine is not in use(fig. 1 B).

■ The dishwasher is fitted with 3/4" threadedconnector (fig. 2) .

■ Connect inlet hose “A” to water tap “B”with a 3/4" attachment making sure thatit has been properly tightened.

■ If it is necessary, the inlet pipe can belengthened up to 2,5 m. The extensionpipe is available from the After SalesService Centre.

■ If limescale deposits or sand are presentin the water, it is advisable to obtain theappropriate filter, art. 9226085, from theAfter Sales Service Centre (fig. 3) . Thefilter “D” must be inserted between the tap“B” and the inlet hose “A” , rememberingto fit the washer “C” .

■ If the dishwasher is connected to newpipes or to pipes which have not been inuse for a long time run water through fora few minutes before connecting theinlet hose. In this way no deposits ofsand or rust will clog up the water inflowfilter.

1

2

3

6

■ Fasten the two supplied frames with 4 ofthe 4 x 16 mm diameter screws, settingthem at the center of the eyelets (fig. 6) .

■ Hang the panel on the dishwasher doorand align it by adjusting the frames withthe eyelets.

■ Fix the frames with the other 6 screws4x16 mm in the specif holes (fig. 6) .

■ Fasten the panel to the dishwasher doorwith the screws 3.5 x 13 mm (fig. 7) .

N.B.:If you wish to fit a wooden panel withfalse drawer, ask for special kit to theAssistance Service.

Wooden panel installation

This dishwasher model is equipped with anauto-balancing system in the door andcomes ready to mount a wooden panel ofthe following size:

Width 596,5 mm max

Height from 645 to 715 mm max

Thickness from 18 to 22 mm max

This allows the use of a regular wing takenfrom a drawer furniture weighing from 4,5to 8,5 kg; for coverings weighing more, askfor information to the Assistance Service.

Drilling arrangements

■ Drill 12 mm deep holes in the panelusing a 2 mm diameter drill according tothe measures indicated in the figure 5 .

715

max

.

645

min

.

350

178

596,5 max.

== 572

6

7

5

9

2

8

TECHNICAL NOTES FORCABINET FITTERS

This dishwasher model can be embeddedin modular furniture, under a counter top, acontinuous counter top or a sink.

■ The housing dimensions must be thesame as those indicated in the figure 1 .

■ The adjustable feet allow the height ofthe machine to be varied from 820 to885 mm.

Installation under the counter top

■ Adjust the dishwasher height to adapt itto the housing “A” dimensions, level itby means of the adjustable feet, whichwill then be blocked with the lock-nut (fig.2-3).

■ Insert the dishwasher in the housing andconnect the dishwasher to water andpower following the instruction booklet;if necessary, re-adjust the front and rearfeet and block them again with thelock-nut.

■ Fasten the dishwasher to the counter topwith the supplied 30 mm long screws“A” (fig. 4) .

600

570

550

550597

100

40

820+

(65)

100

170+(

65)

820+

(65)

160

598

1

3

4

8f

11

8e

620 min.

9

8a

8b

8c

8d10

ImportantIf, after mounting the wooden panel, it isnecessary to ship the machine for finalinstallation, we recommend leaving it in itsoriginal packaging materials.For this reason the package was design toallow the panel to be mounted withouthaving to unpack the machine completely.Follow figures 8a-f sequentially.

A) Cut the polythene with a Knife (fig. 8a) .

B) Lift the cardboard flap up and removethe wooden slat (fig. 8b) .

C) To open the dishwasher remove thepolystyrene from the sides (fig. 8c) .

D) Fix the décor panel to the matchingkitchen door (fig. 5-6) , then while thedishwasher door is in the openposition attach it to the machine usingthe 6 screw 3.5 x 13 mm (fig. 8d) .

E) Replace the cardboard and film in itsoriginal position (fig. 8e) .

F) Re–seal the packaging (fig. 8f) .

Adaptation of the base

Sometime, in order to allow the doorrotation, a space must be cut out in thebase as indicated in the figure 9 .

Proceed as follows:

■ Open slightly the dishwasher door, letthe covering touch the base and mark itslower edge on the base with a pencil; cutout the interfering part.

Loading the salt

■ On the bottom of the machine there is acontainer for the salt for regeneratingthe softener.

■ It is important to use only a salt that isspecifically designed for dishwasher.Other types of salt contain small quantitiesof insoluble particles which over a longperiod of time may affect and deterioratethe softener performance.

■ To add salt, unscrew the cap of the con-tainer on the bottom and then refill thecontainer.

■ During this operation a little water willoverflow; but keep adding salt until thecontainer is full. When the container isfull, clean the thread of salt residue andretighten the tap.

■ After loading the salt, it is recommendedrunning a complete washing cycle,or COLD RINSE programme. The salt dispenser has a capacity ofbetween 1.5 and 1.8 kg and, for efficient

13

Salt loading indicator

This model is provided with a blind cap. Inthis case, the salt level must be checkedperiodically, according to the regulation ofthe water softener unit.

IMPORTANT The appearance of white stains ondishes is generally an importantsign that the salt container needsfilling.

use of the appliance, it should be refilledfrom time to time according to theregulation of the water softener unit.

IMPORTANT(Only for first start up)When the appliance is used for thefirst time, after completely filling thesalt container, it is necessary to addwater until the container overflows.

If your water is at level 0, you need not useany regenerating salt, nor need you makeany adjustment, as your water is soft.

According to the degree of hardness ofyour water, regulate the softener unit in thefollowing way:

1. remove the lower rack. Unscrew andremove the cap from the salt dispenserlocated in the bottom of the tub(fig. A"1") ;

2. turn the selector screw to the requiredposition with a screwdriver or a knife.

12

TYPE 1

TYPE 2

WATER SOFTENER UNIT

Depending on the source of the supply,water contains varying amounts of limestoneand minerals which are deposited on thedishes leaving whitish stains and marks.The higher the level of these mineralspresent in the water, the harder the water is.The dishwasher is fitted with a watersoftener unit which, through the use ofspecial regenerating salt, suppliessoftened water for washing the dishes.The softener unit can treat water with ahardness of up to 60°fH (French grading)or 33°dH (German grading) through fivedifferent settings.The degree of hardness of your water canbe obtained from your water supplycompany.

Regulating the water softener

The table below lists different degrees ofwater hardness with the corresponding set-ting for the softener unit.

*The water softener unit is set in thefactory at level 2, as this is suitable for themajority of users.

Level

01*234

Waterhardness

°fH(French)

0-910-3031-4041-5051-60

Waterhardness

°dH(German)

0-56-16

17-2223-2728-33

Use ofregenerating

salt

NOYESYESYESYES

Watersoftenersetting

FREEposition N.1position N.2position N.3position N.4

N°of

washes

50403020

15

A standard daily load is represented in figs. 1, 2 and 3.

Upper basket (fig. 1)A = soup platesB = dinner platesC = dessert platesD = saucersE = cupsF = glasses

Upper basket (fig. 2)A = soup platesB = dinner platesC = dessert platesD = saucersE = cupsF = glassesG = single section cutlery basket

Lower basket (fig. 3)A = medium-sized saucepanB = large saucepan C = frying panD = lidsE = tureens, serving dishesF = cutleryG = oven dishes

Please load the dishwasher sensibly to ensure thebest wash results.

Cutlery basket (fig. 4) The cutlery basket is made with two detachableparts which will enable various loading options. Thetwo parts can be detached by sliding the left sectionaway from the right section.

14

LOADING DISHES

Using the upper basket

■ The upper basket is provided with mobi-le racks hooked to the sides of thebasket which can be regulated in twopositions: upright and lowered. In thelowered position the racks may be usedfor tea and coffee cups, kitchen knivesand ladles. Glasses with stems may besafely hung on the ends of the racks.Glasses, cups, saucers and dessertplates may be loaded under the racks.

■ Soup plates and ordinary plates may beloaded with the rack in the uprightposition. Plates should be loadedvertically with the underside of the platetowards the back of the dishwasher witha space between each plate to allowwater to pass freely.

■ It is advisable to load plates of the samesize together in order to utilize maximumbasket capacity.

■ Plates may be loaded in a single row(fig. 1) or on both rows (fig. 2) .

■ It is advisable to load large plates(approx. 27 or more cm) slightly tiltedtowards the rear to facilitate introductionof the basket into the machine.

■ Salad bowls and plastic bowls may alsobe loaded on the upper basket. It isadvisable to block these in place so thatthe jets of water do not make themoverturn.

■ The upper basket has been designed tooffer maximum flexibility in use and canbe loaded with up to 24 plates on tworows, up to 30 glasses on five rows or amixed load.

Using the lower basket

■ Saucepans, oven dishes, tureens, saladbowls, lids, serving dishes, dinnerplates, soup plates and ladles can beloaded on the lower basket.

■ Place the cutlery in the plastic cutleryholder with the handles pointingupwards.

■ Place the cutlery holder on the lowerbasket (fig. 3) , making sure that thecutlery does not get in the way of therotating arms.

IMPORTANTThe lower basket has a safety-stopdevice, for its safe extraction, alsoespecially useful with a full load.For loading salt, cleaning filter and forordinary maintenance, the completeextraction of the basket is necessary.

D F A G

EB

C

3

4

A

B

C

D

G

E

F

2 F

1A

BC

D

E

F

17

Half load wash upper basket

1/2 mixed load (fig. 1)A = glassesB = soup platesC = dessert platesD = saucersE = saucepanF = Irying panG = large bowlH = small bowl

1/2 load standard (fig. 2)A = 6 glassesB = 6 cupsC = serving dishD = 6 soup platesE = 6 dinner platesF = 6 dessert platesG = 6 saucersH = medium bowlI = small bowl

Place the cutlery in the plastic cutlery holder on the lower basket.Lower basket (fig. 6)M = 8 + 4 soup platesN = 11 + 1 dinner platesO = 12 dessert platesP = serving dishQ = cutlery

16

Upper basket (fig. 5) A = 5 + 5 + 2 glassesB = 12 saucersC = 4 + 6 + 2 cupsD = small bowlE = medium bowlF = large bowlG = 1 forkH = 1 + 1 serving spoonsI = 3 + 3 dessert spoonsL = 3 + 3 teaspoons

INFORMATION FOR THE TEST LABORATORIES

General programme comparison (Ref. EN 50242 Standards) (see programmes selection)

1. Upper basket position: low2. Normal load3. Shine setting: 6

12 international place load (Ref. EN 50242)Correct loading is indicated, in fig. 5 for the upper basket, in fig. 6 for the lowerbasket and in fig. 7 for the cutlery basket.

Cutlery basket without side racks (fig. 7)Insert the remaining cutlery, taking care not toload more than two different types of cutlery inthe same compartment.

4. Amount of detergent:- 8 g for pre-wash;- 22 g for wash.

AF

C

C

C

G

B

ED

H H

5

L

I

Q N

MP

O

M

N

6

A

A

A

EG

B

H

D

C

F

1

A

G

IB

C

FE

H

D

2

7

19

FULL EMPTY

dark light

Filling the rinse aid container

The rinse aid, which is automaticallyreleased during the last rinsing cycle, helpsthe dishes to dry quickly and preventsspots and stains forming.The rinse aid container can be found to theleft of the detergent container (fig. A "3") .

To open the lid, push the reference markand, in the same time, pull the tab ofopening.

It is always advisable to use rinse aid thatis specifically designed for dishwasher.Check the rinse aid level through theindicator eye (C) which is located on thedispenser.

Regulating the rinse aid from 1 to 6

The regulator (D) is placed under the lidand can be turned using a coin. The recommended position is 4.The limestone content of the waterconsiderably affects the formation oflimescale and the drying performance.It is therefore important to regulate thequantity of rinse aid to achieve goodwashing results.If, after the wash, streaks occur on thedishes, decrease the amount by oneposition. If whitish spots occur, increase theamount by one position.

■ the effectiveness of detergents containingthe built in water softener/salt dependson the hardness of your water supply.Check that the hardness of your watersupply is within the effective range givenon the detergent packaging.

In certain circumstances use of combineddetergents can cause:

■ limescale deposits on dishes or in thedishwasher;

■ a reduction in washing and dryingperformance.

Should this occur, we would recommendusing traditional separate products – salt,detergent and rinse agent. This will ensurethat the water softener in the dishwasheroperates correctly. Please note that on return to the use ofconventional salt, a number of cycles willbe required before the system becomesfully efficient again.

IMPORTANTAny problems which arise as a directresult of the use of these productsare not covered by our warranty.

C

D

LOADING THE DETERGENTAND THE RINSE AID

Filling the detergent container

IMPORTANTIt is essential to use a detergentthat is specifically designed fordishwashers either in powder, liquidor tablet form.

“FINISH” gives very good results and canbe easily obtained.

Unsuitable detergents (like those forwashing up by hand) do not contain theproper ingredients for use in a dishwasher,and stop the dishwasher from workingcorrectly.

Normal wash

The detergent container is inside the door(fig. A “2”) . If the lid of the container isclosed, press the button (A) to open. At the end of every wash cycle the lid isalways open and ready for the next timethe dishwasher is used.The amount of detergent to be used variesaccording to how dirty the dishes are andon the type of dishes to be washed.We advise using 20:30 g of detergent in thewash section of detergent compartment (B).

18

After pouring the detergent into the container,close the lid, firstly pushing (1) and thenpressing on it (2) until you hear the click.

Since not all detergents are the same theinstructions on the boxes of detergent canvary. We should just like to remind usersthat too little detergent does not clean thedishes properly whilst too much detergentwill not produce better results and is also awaste.

IMPORTANTDo not use an excessive amount ofdetergent and help limit damage tothe environment at the same time.

CAUTION! IMPORTANT NOTE ON THE USE OFCOMBINED DETERGENTS.

If you are planning to use combined detergentsi.e. those with built in salt and/or rinseagent, we would advise the following:

■ read carefully and follow the manufacturer’sinstructions given on the packaging;

■ some combined detergents, particularlythose with built in rinse agent, providebest results when used with specificprogrammes;

A

B

21

PRATICAL HINTS

How to get really good washresults

■ Before placing the dishes in thedishwasher, remove any remainingfood (bones, shells, pieces of meat orvegetables, coffee grounds, skin of fruit,cigarette ash, tooth picks etc. to avoidblocking the filters, water outlet andwashing arm nozzles.

■ Try not to rinse the dishes beforeloading them into the dishwasher.

■ If saucepans and oven dishes areencrusted with the remains of burnt orroast food, it is advisable to leave themto soak before washing.

■ Place the dishes face downwards.

■ Try to place the dishes in such a waythat they are not touching one another.If they are loaded properly you will getbetter results.

■ After loading the dishes check that thewashing arms can rotate freely.

■ Pans and other dishes that haveparticularly stubborn food particles orremnants of burnt food should be left tosoak in water with dishwasherdetergent.

■ To wash silver properly:

a) rinse the silver immediately afteruse, especially if it has been used formayonnaise, eggs, fish etc.;

b) do not sprinkle detergent onto it;

c) keep it separate from other metals.

How to make savings

■ If you want the dishwasher to give acomplete wash, place the dishes in thedishwasher at the end of each meal andif necessary turn on the COLD RINSEcycle to soften the food remains andremove bigger particles of food from thenew load of dishes. When the dishwasher is full start thecomplete wash cycle programme.

■ If the dishes are not very dirty or if thebaskets are not very full select anECONOMY programme, following theinstructions in the program list.

What not to wash

■ It should be remembered that not alldishes are suitable for washing in adishwasher.We advise against usingthe dishwasher to wash items inthermoplastic, cutlery with wooden orplastic handles, saucepans withwooden handles, items in aluminium,crystal, leaded glass unless otherwisestated.

■ Certain decorations may fade. It istherefore a good idea before loading thewhole batch to wash just one of theitems first so as to be sure that otherslike it will not fade.

■ It is a good idea not to put silver cutlerywith non-stainless steel handles intothe dishwasher as there could be achemical reaction between them.

IMPORTANTWhen buying new crockery orcutlery always make sure that they aresuitable for washing in a dishwasher.

Useful hints

■ In order to avoid any dripping from thetop rack, remove the lower rack first.

■ If the dishes are to be left in themachine for some time, leave the doorajar, to let some air circulate and toimprove the drying performance.

20

1

2

3

CLEANING THE FILTERS

The filter system (fig.A “4”) consists of:

a central container that traps the largerparticles;

a flat gauze that continuously filters thewash water;

a micro filter , located beneath the gauze,that traps the tiniest particles ensuring aperfect rinse.

■ To achieve excellent results every time,the filters should be checked andcleaned after each wash.

■ To remove the filter unit, simply turn thehandle anticlockwise (fig. 1) .

■ For ease of cleaning, the central containeris removable (fig. 2) .

■ Remove the gauze filter (fig.3) andwash the whole unit under a jet ofwater. If necessary a small brush canbe used.

■ With the Self-cleaning Micro filter ,maintenance is reduced and the filterunit need only be checked every twoweeks. Nevertheless, after each wash itis advisable to check that the centralcontainer and the gauze filter are notclogged.

WARNING!After cleaning the filters, make surethat they are correctly reassembledand that the gauze filter is properlypositioned at the bottom of thedishwasher.

Make sure that the filter is screwedback, clockwise, into the gauze, aspoor seating of the filter unit couldhave an adverse effect on theefficiency of the appliance.

IMPORTANTNever use the dishwasher withoutthe filters.

22

WHEN CYCLE IS FINISHED

After every wash it is essential to turn offwater supply and to switch off the machineby pressing the On/Off button to the offposition.

If the machine is not going to be used forsome time, it is advisable to follow theserules:

1. do an empty wash with detergent in orderto clean the machine of any deposits;

2. pull out the electric plug;

3. turn off the water tap;

4. fill the rinse aid container;

5. Ieave the door ajar;

6. keep the inside of the machine clean;

7. If the machine is left in places where thetemperature is below 0°C any water leftinside the pipes may freeze. Wait untilthe temperature rises above zero andthen wait for about 24 hours beforestarting up the dishwasher.

CLEANING AND MAINTENANCE

■ To clean the dishwasher outside, do notuse solvents (degreasing action) neitherabrasives, but only a cloth soaked withwater.

■ The dishwasher does not require specialmaintenance, because the tank isself-cleaning.

■ Regularly wipe the door gasket with adamp cloth to remove any food remainsor rinse aid.

■ It is advisable to remove limestonedeposits or dirt periodically, by doing anempty wash; pour a glass of vinegar onthe bottom of the tank and select thelight wash.

■ If, in spite of the routine cleaning of thefilters, you notice that the dishes or pansare not properly washed or rinsed, checkthat all the spray heads on the rotorarms (fig. A “5”) are clear.

If they are blocked, clean them in thefollowing way:

1. to remove the upper rotor arm, turn ituntil it lines up with the stop markedby the arrow (fig. 1) . Push it upwards(fig. 1b) and, keeping it pushed in,unscrew it in a clockwise direction(to reassemble it repeat the sameoperation, but turn it anticlockwise).The lower rotor arm can be removedsimply by pulling it upwards (fig. 2) ;

2. wash the rotor arms under a jet of waterto clear any blockage in the sprayheads;

3. when you have finished, refit the rotorarms in the same position, rememberingto re-align the arrow and screw intoposition.

■ Both the door lining and the tank liningare in stainless steel; however, shouldspots caused by oxidation occur, this isprobably due to a high level of iron saltspresents in the water.

■ The spots can be removed with a mildabrasive agent; never use chlorinebased materials, steel wool, etc.

1

2

1b

23

EN 50242 place loadCapacity with pans and dishesWater supply pressure FusePower inputSupply voltage

128 personsMin. 0,08 - Max 0,8 MPa(see rating plate)(see rating plate)(see rating plate)

DESCRIPTION OF THE CONTROL

TECHNICAL DATA:

DIMENSIONS:

HeightDepth Width Depth with door open

cmcmcmcm

82 ÷ 88,555

59,8117

A "ON/OFF" button

B PROGRAMME DESCRIPTION

C "PROGRAMS" buttons

D "HALF LOAD" button

E "OPTION SELECTION" LED

F "PROGRAM SELECTION" LEDs

D B A

F

C

E

24

PROGRAM SELECTION AND SPECIAL FUNCTIONS

(Use in conjunction with programme guide)

Program settings

■ Open the door and place dirty dishesinside the appliance.

■ Press the "ON/OFF" button .

■ After pressing the "ON/OFF" button,the LED for the factory set is"recommended” (which is ideal for fullload daily use) or the LED for the "Auto’Memory" program (see below) will blink.

IMPORTANTThe dishwasher has two very practicalfunctions:

- the "recommended" program( ) for quick and sure selection;

- the "Auto’ Memory", function whichsaves a program used at least 3times consecutively so that if youregularly use the same washing cycleeach time you do not have tocontinually set the program therebysaving time and effort.

■ If you wish to select an option, press theoption button (the corresponding LEDwill light).

The option button must be pressedBEFORE the program starts for theoption to be accepted.

■ To choose another program, press thecorresponding button (the relevant LEDwill blink to confirm the selection).

IMPORTANTTo select the "COLD RINSE" program,simultaneously press the "RAPID"program button and "HALF LOAD"option button (the relevant LEDs willblink, confirming the selection).

■ To start the program, press the selectedprogram button again to confirm. Therelevant LED will stop blinking andremain on and, when the door is shut,the program will start automatically.

IMPORTANTTo confirm the “COLD RINSE” program,simultaneously press the “RAPID”program button and the “HALFLOAD” option button (the relevantLEDs will stop blinking and remainon to confirm the selection).

Program interruption

Opening the door when a program isrunning is not recommended especiallyduring the main washing and final hot rinsephases. However, if the door is openedwhile a program is running (for example,to add dishes) the machine stopsautomatically.Close the door, without pressing anybuttons. The cycle will start from where itleft off (if it is necessary, the appliancewill make a short thermal anti-shockprogramme before).

Changing a running program

Proceed as follows to change or cancel arunning program:■ Hold down the current program button

(with the LED on) for at least 3 seconds.The program LEDs (except for the"RAPID" program LED) will start to blink.

WARNING!Don't switch off the dishwasher,before the end of the water discharge.

■ Close the door to allow the water to bedischarged.The running program will be cancelledand the LED for the “recommended”program or the LED for the program thatwas used at least 3 times consecutivelywill start to blink.

25

IMPORTANT To cancel the "COLD RINSE" program,simultaneously hold down the"RAPID" program button and "HALFLOAD" option button.

■ At this point a new program can be set.

WARNING!Before starting a new programme,you should check that there is stilldetergent in the dispenser. If necessary, top up the dispenser.

If there is any break in the power supplywhile the dishwasher is operating, aspecial memory stores the selectedprogramme and, when the power isrestored, it continues where it left off (ifit is necessary, the appliance will makea short thermal anti-shock programmebefore).

Program end

At the end of the program, the LED for the“recommended” program or the LED forthe program that was used at least 3 timesconsecutively will start to blink. Dishes can now be removed and thedishwasher turned off by pressing the"ON/OFF" button or dishes can be loadedfor new cycle.

Option button

"HALF LOAD" button

By using this option, it is possible to washa smaller quantity of crockery: you shouldload only the upper basket for dishes andplace cutlery in the tray in the bottombasket.This reduces water and energy consump-tion and requires a smaller quantity ofdetergent.

IMPORTANT This button MUST be set BEFORE theprogram starts.

Fault signals

If malfunctions or faults occur when aprogram is running the LED thatcorresponds to the selected cycle (2 LEDsfor the "COLD RINSE" program) will blinkrapidly.In this case, turn the dishwasher off bypressing the "ON/OFF" button. Afterchecking to make sure the water intel hosetap is open, that the drain hose is not bentand that the siphon or filters are notclogged, set the selected program again. Ifthe anomaly persists, contact CustomerService.

IMPORTANTThis dishwasher is equipped with ananti-overflow safety device which willautomatically empty any excesswater should a problem occur.

WARNING!To ensure the correct operation ofthe anti-overflow safety device, it isrecommended not to move or to tiltthe dishwasher during operation.If it is necessary to move or to tilt thedishwasher, first make sure thewashing cycle is finished and that nowater is left in the tank.

2726

5• ••

• • • •

•• • 50°C 32••

65°C 95••

• • • • 45°C 140••• ••

••••

•

• • • • • •• 75°C 120•• •••• YES

YES

Programme

PROGRAMME SELECTION

Check list Avarageduration

in minutes

Special functionbuttons

available

Det

erge

nt fo

r so

akin

g(P

rew

ash)

Det

erge

nt fo

r w

ashi

ng

Cle

an fi

lter

Che

ck r

inse

aid

di

spen

ser

Che

ck s

alt c

onta

iner

Hot

pre

-was

h

Col

d pr

e-w

ash

Mai

n w

ash

Firs

t col

d rin

se

Sec

ond

cold

rin

se

Hot

rin

se w

ith r

inse

aid

With

col

d w

ater

(15°

C)

-Tol

eran

ce ±

10%

-

"HA

LF L

OA

D"

butto

n

Programme contents

Description

YES

Wash with prewash If setting the HYGIENIC wash programme, a second dose of about 20 g of detergent(1 table-spoon) must be added directly in the machine.

(“RECOMMENDED” PROGRAMME)Once a day - for normal soiled pans and anyother items that have been left all day forwashing.

Once a day - for heavily soiled pans and anyother items that have been left all day forwashing.

Energy Saving Programme suitable fornormal soiled items. Using detergents withenzyme.Programme standardised to EN 50242.

Quick wash for dishes which are to bewashed immediately after the meal. Washload of 4/6 persons.

Short cold pre-wash for items that are storedin the dishwasher until you are ready towash a full load.

UNIVERSAL

HYGIENIC

ECO

RAPID 32’

COLD RINSE

+

29

N.B.: Should any of the situations occur and should the machine give a bad wash performance,it is necessary to remove the deposits from the dishes by hand since the final drying cycle hardens thedeposits which a second wash in the machine would not be able to remove.

If the malfunction continues contact a Service Centre quoting the serial number of the dishwasher.This is found on the plaque on the inside of the dishwasher door at the top or on the guarantee. This information will make it possible to take more effective action more quickly.

The manufacturers decline any responsibility for any printing mistakes in this instruction booklet.They also reserve the right to modify their own appliances as necessary without altering theessential characteristics.

FAULT CAUSE REMEDY

7 - Load of dishes is only partially washed

8 - Presence of white spots on dishes

9 - Noise during wash

10 -The dishes are not completely dry

See causes for no. 5

Bottom of saucepans have notbeen washed well

Edge of saucepans have not been washed well

Spray arms are partially blocked

The dishes have not been properly loaded

The end of the outlet hose is inthe water

The incorrect amount of detergent has been measuredout; the detergent is old and hard

The wash programme is not thorough enough

The lower basket dishes havenot been washed

Water is too hard

The dishes knock against oneanother

The revolving arms knock againstthe dishes

Inadequate air flow

Check

Burnt on food remains must be soaked before putting pansin dishwasher

Reposition saucepans

Remove spray arms byunscrewing ring nuts clockwiseand wash under running water

Do not place the dishes too closely together

The end of the outlet hose must not come into contact with the outflow water

Increase the measure according to how dirty thedishes are and change detergent

Choose a more vigorous programme

Depress half load button

Check salt and rinse aid leveland regulate amount. Should the fault persist, Contact Service Centre

Re-check loading of dishes inthe basket

Again re-check loading

Leave the dishwasher door ajarat the end of the wash programto allow the dishes to dry naturally

IDENTIFYING MINOR FAULTS

Should the dishwasher fail to operate, before contacting the Service Centre, makethe following checks:

28

FAULT CAUSE REMEDY

1 - Machine completely dead

2 - Machine does not draw water

3 - Machine does not discharge water

4 - Machine discharges water continuously

5 - Spray arms are not heardto rotate

6 - On electronic applianceswithout a display: one ormore LED flashing quickly.

Plug is not connected to wallsocket

O/I button has not been pressed

Door is open

No electricity

See causes for no. 1

Water tap is turned off

Programme selector is not atcorrect position

The inlet hose is bent

The inlet hose filter is not correctly connected

Filter is dirty

Outlet hose is kinked

The outlet hose extension isnot correctly connected

The outlet connection on thewall is pointing downwards notupwards

Position of outlet hose is toolow

Excessive amount of detergent

Item prevents arms from rotating

Plate and cup filter very dirty

Water inlet tap turned off

Connect electric plug

Press button

Close door

Check the fuse in the plug and the electricity supply

Check

Turn water tap on

Turn programme selector tocorrect position

Eliminate the bends in the hose

Clean the filter at the end of thehose

Clean filter

Straighten outlet hose

Follow the instructions for connecting the outlet hosecarefully

Call a qualified technician

Lift outlet hose to at least 40 cmabove floor level

Reduce amount of detergent Use suitable detergent

Check

Clean plate and cup filter

Switch off the appliance.Turn on the tap.Re-set the cycle.

The manufacturer declines all responsibility in the event of any printing mistakes in thisbooklet. The manufacturer also reserves the right to make appropriate modifications toits products without changing the essential characteristics.

04.0

9 -

4101

2895

- P

rinte

d in

Ita

ly -

Im

prim

é en

Ita

lieEN