controls lvl 1 - zodiac pool professional access/media/80b7293a649e478c8f… · fsoft 21 notes:...

SELECTIONCONTROLS LVL 1

2

Zodiac Academy [email protected]

www.zodiacacademy.com

Zodiac® Pool Systems, Inc. 1-800-822-7933 Regional Extension_________________ www.ZodiacPoolSystems.com

Instructor: _____________________________________Email:___________________________

Sales person: ___________________________________Phone:__________________________




Service Manager: ________________________________Phone:__________________________

Service Manager: ________________________________Phone:__________________________

IMPORTANT SAFETY INSTRUCTIONSThe information contained in this technical guide is intended for Zodiac trained service personnel only. Electrical installation and repairs should only be performed by a certified electrician or Zodiac trained professional. and must comply with all national electric codes (NEC®, Canadian, etc.). state and local law, ordinances, codes and regulations.

If you have not received training, do not attempt any of the electrical repairs presented in this document. Contact Zodiac Pool Systems, Inc. at 1-800-822-7933 for assistance.

Read and follow all instructions carefully.When servicing equipment, basic safety precautions should always be followed including those listed below.

TO REDUCE THE RISK OF ELECTRICAL SHOCK:• Disconnect main power to pool equipment area prior to any service or repairs.

• Keep all electrical equipment at least 10 feet (3m) from inside wall of pool or spa.

• Connect equipment only to a receptacle (cord models) or circuit (hardwired) protected by a ground fault circuit interrupter (GFCI).

• Use only copper conductors and supply wires suitable for the specific device.

• Replace damaged power cord(s) immediately and use only identical replacement parts.

• Do not bury power cord(s). Position cord(s) to minimize abuse from lawn mowers, hedge trimmers and other equipment.

• Do not install or service equipment if precipitation is present or imminent.

TO REDUCE EQUIPMENT WATER PRESSURE HAZARD:• Always turn pump off to release pressure prior to removing or installing in-line equipment.

• To avoid equipment damage, do not exceed water pressure (psi) specifications for the device.

To reduce the risk of injury, do not permit children to operate, handle or play on equipment.

CONFIDENTIAL | PROPERTY OF ZODIAC POOL SYSTEMS, INC.

Models

iAquaLink™ All Revisions

Z4

AquaLink RS 8

All Button Rev C

OneTouch™ Rev I

Touch™ Rev Q

iAquaLink Rev R

AquaLink® RS

iAquaLink Rev 7.0

PDA

Hand Held All Revisions

Discontinued 2015


Models Z4 PDA AquaLink® RS

4

Notes:


RS-PS8 Finished Goods

Type: P = Pool or Spa Only PS = Pool and Spa Combination 2-X = Dual Equipment (available with AquaLink RS)

Model Number: RS = AquaLink® RS PDA = Pool Digital Assistant ZQ = Z4

Functions: # = The number of high voltage relays

iAquaLink™: Note: An “I” at the end of the Z4 indicates the model comes with the iAquaLink

Part Numbers i


Models

Selection Process

What is not an auxiliary piece of equipment, i.e. What equipment is always controlled?

•With a Pool and Spa Combination Model? •With a Pool or Spa Only Model? •With a Dual Equipment Model?

What is an auxiliary piece of equipment?


Hydraulics Identification


HOT CHAUD

Plumbing Pool and Spa Combination System

Inlet or

Suction

Pool

Pool

Spa

Spa

Outlet or

Return


HOT CHAUD

Plumbing Pool or Spa Only System

Outlet or

Return

Inlet or

Suction


Plumbing Pool and Spa Dual Equipment AquaLink® RS systems only

HOT CHAUD

HOT CHAUD

Pool Equipment

Spa Equipment

Outlet or

Return

Outlet Or

Return

Inlet or

Suction

Inlet or

Suction

7

Notes:


AquaLink® Z4


Jandy® Valve Actuators Sensors

Water

Air

Pool and Spa Combination Model Z4 p/n: ZQ-4PS

Note: 4 Standard 3 HP relays come mounted in the Z4 IN

LET

Jandy Valve Actuator JVA 2444

INLE

T


8

Notes:


Pool and Spa Combination Model Z4 p/n: ZQ-4PSi

Note: 4 Standard 3 HP relays come mounted in the Z4

Jandy® Valve Actuators Sensors

Water

Air

iAquaLink™ 1.0 & 2.0

INLE

T


INLE

T



Sensors

Water

Air

Pool or Spa Only Model Z4 p/n: ZQ-4P



Pool or Spa Only Model Z4 p/n: ZQ-4Pi


Sensors

Water

Air iAquaLink™

1.0 & 2.0

10

Notes:


PDA

3 HP Relays

Pool and Spa Combination Model PDA 8 p/n: PDA-PS8

Bezel w/PCB from spring 2013 to present

ON

O

N

Jandy® Valve Actuators

INLE

T


Sensors

INLE

T


Water

Air

3 HP Relays

Pool or Spa Only Model PDA 8 p/n: PDA-P8

Bezel w/PCB from spring 2013 to present

ON

O

N

Sensors

Water

Air


AquaLink® RS


INLE

T


Sensors

INLE

T


Water

Air

Bezel w/PCB

3 HP Relays

Pool and Spa Combination Model AquaLink® RS 8 p/n: RS-PS8

ON

O

N

12

Notes:

Jandy Valve Actuators

INLE

T


Sensors

INLE

T


Water

Air

Bezel w/PCB

3 HP Relays

Pool and Spa Combination Model AquaLink® RS 32 p/n: RS-PS32

ON

O

N

AUX B1 AUX B2 AUX B3 AUX B4 AUX B5 AUX B6 AUX B7 AUX B8

AUX B1 JVA

AUX B2 JVA

AUX B3 JVA

AUX B4 JVA


AUX B1 JVA

AUX B2 JVA

AUX B3 JVA

AUX B4 JVA


AUX B1 JVA

AUX B2 JVA

AUX B3 JVA

AUX B4 JVA

RP3

VR1

SWREG1

D1

RP4

U4

W 1 W 2

The position of jumpers W1 and W2 determine the address of the Auxiliary PCB.

FIRST AUXILIARY POWER CENTER PCB

SECOND AUXILIARY POWER CENTER PCB

THIRD AUXILIARY POWER CENTER PCB

W1 W2

W1 W2

W1 W2

13

Notes:

Sensors

Water

Air

Bezel w/PCB

3 HP Relays

Pool or Spa Only Model AquaLink® RS 8 p/n: RS-P8

ON

O

N

Sensors

Water

Air

Bezel w/PCB

3 HP Relays

Pool or Spa Only Model AquaLink® RS 16 p/n: RS-P16

ON

O

N


AUX B1 JVA

AUX B2 JVA

AUX B3 JVA

AUX B4 JVA

Sensors

Pool Water

Air

Bezel w/PCB

3 HP Relays

Pool and Spa Dual Equip. Model AquaLink® RS 2/6 p/n: RS 2-6

ON

O

N

Spa Water

Heater Interface Kit

Sensors

Pool Water

Air

Bezel w/PCB

3 HP Relays


ON

O

N

Spa Water


Sensors

Pool Water

Air

Bezel w/PCB

3 HP Relays


ON

O

N


AUX B1 JVA

AUX B2 JVA

AUX B3 JVA

AUX B4 JVA


AUX B1 JVA

AUX B2 JVA

AUX B3 JVA

AUX B4 JVA


AUX B1 JVA

AUX B2 JVA

AUX B3 JVA

AUX B4 JVA

Spa Water



Power Centers Note: Power Centers are for PDA and AquaLink® RS

Foundation Power Center p/n: 6612F

Standard Power Center p/n: 6613

PureLink Standard Power Center p/n: 6613AP

Sub Panel Power Center p/n: 6614-LD

PureLink Sub Panel Power Center p/n: 6614AP-L

18

Notes:


User Interfaces


Z4 User Interface • Mounted at the power Center • Can be relocated • Standard 4 conductor telephone cable

Z4 - User Interface

Power Alert

Zodiac 11:43 AM

Pool Mode Pool Heater Spa Mode Spa Heater Settings Devices Service Mode

Off Off Off Off > > >

®

Optional: iAquaLink™ iAquaLink is a Web based control which will operate with all Z4 control systems.



PDA User Interface • PDA Handheld color change

PDA - User Interface

Optional: iAquaLink™ iAquaLink is a Web based control that was released in 2013 and first supported by Rev 6.0.



AquaLink® RS - User Interfaces

AquaLink RS 8 PUMP OFF

All Button: Released in 1996 and supported by Revision C firmware.

52

RESET

CANCEL DELAY

RESET

SELECT

BACK DONE OneTouch™: Introduced in 2000 and first supported

by Rev I firmware.

Touch™: Touch or AquaLink Touch was released in 2010 and first supported by Rev Q firmware.

Mon Feb 26, 2012

Spa Temp 100º

Air Temp 75º

FILTER PUMP

SPA POOL HEAT

SPA HEAT

AUX 1 AUX 2 AUX 3 Other Devices On/Off

My iAquaLink

iAquaLink™: iAquaLink and iAquaLink are Web based controls that were released in: • 2012 iAquaLink Rev R

• 2014 iAquaLink2.0 Rev T.

20

Notes:


Chlorine Generators Optional Salt Systems Z4, PDA & AquaLink® RS


PLC

Chlorine Generators p/n: PLC 700 p/n: PLC 700-25 p/n: PLC 1400 p/n: PLC 1400-25 p/n: FSOFT1400 p/n: FSOFT700

Salt Water Cell Kits A 700 cell is designed for a pool up to 12,000 gallons. A 1400 is designed for a pool up to 40,000 gallons

For all systems (Z4, PDA & AquaLink® RS)

FSOFT

21

Notes:


Accessory Equipment

Optional


Common

Normally Open (NO)

Normally Closed (NC)

Two Speed Motor Relay p/n: 6796 Coil: 24 VDC Contacts: 2 HP at 240 VAC 1 HP at 120 VAC

Coil wires 24 VDC

Contacts Single Pole Double Throw

Two Speed Motor Relay Allows control of a two speed motor



Sensor

10 K Ohms Thermistor

Water, Air or Solar Sensor All sensors are 10 K Ohms thermistors. A thermistors is a type of resistor whose resistance changes with temperature.

Temp Sensor Kit p/n: 7790 = 15’ 7786 = 50’ 7791 = 125’




INLE

T

Ope

n Co

mm

on P

ort

Jandy Valve Actuator

JVA 2444

OFF

NE

VER

LU

BE

JAN

DY

VALV

E

Jandy Valve Actuator (JVA) • 24 VAC • Standard rotation is 180 degrees • Use in conjunction with Never Lube valves. • Pool and Spa combination systems come with two JVAs.

Jandy® Valve Actuator p/n: 4424



Green

Yellow

Black

Red

Multiplex Board (comes with PureLink™ Power Centers) p/n: 6584 Additional 4 Conductor Terminal Bars


AquaLink Handheld

AquaLink® Wireless Remote p/n: AQPLM

J-Box For Z4 & AquaLink RS

6 5 4 3 2 1

ON

FIL- PMP

AUX 1

AUX 2

AUX 3

AUX 4

AUX 5

AUX 6

AUX 7 SLR-PMP E-HTR INTAKE RETURN CLEANER SOLAR

AUTO

SERVICE

TIME OUT

RESET

HEATER SOLAR

POOL MODE

SPA MODE

SPA DRAIN

SPA FILL

SPARE

ON

3

2

1

4

4 Function Spa Side Remote p/n: Various based on length & color

For PDA & AquaLink® RS

RED

BLA

CK

YELL

OW

GR

EEN

ON

FIL- PMP

AUX 1

AUX 2

AUX 3

AUX 4

AUX 5

AUX 6

AUX 7 SLR-PMP E-HTR INTAKE RETURN CLEANER SOLAR

AUTO

SERVICE

TIME OUT

RESET

HEATER SOLAR

POOL MODE

SPA MODE

SPA DRAIN

SPA FILL

SPARE

ON

OFF

Temp Display

Air Temp

SpaLink RS *

SpaLink 8 Function Spa Side Remote p/n: Various based on length & color For AquaLink® RS only


PolarisWatermatic

C1900

ChemLink • Digital control • Connects only with AquaLink® RS Rev P or newer or PDA Rev 5 or newer or later control systems. • Read and feed both ORP and pH. p/n: C1900

For PDA & AquaLink RS


PWR CTR A

PWR CTR B

CONTROLLER

A / B

RS InterLink Allows two Main Power Centers to communicate with one OneTouch™ or Touch™ control panel. p/n: INTERLINK

For AquaLink® RS only


Light Dimming Relay p/n: 6587 Coil: 24 VDC Pulsing Contacts: 1000 Watts Incandescent lights only 12 to 120 VAC

Coil wires 24 VDC

Light Dimming Relay A light dimming relay is used to dim incandescent lighting (standard white lights) only. It cannot be used to dim colored lights, LED lights or quartz halogen lights. The contact is rated for up to 1000 watts of incandescent lighting.

NEU

TRA

L

OU

TPU

T H

OT

120

VAC

H

OT

WARNING: A G.F.C.I. must be installed between circuit breaker and the dimming relay

For AquaLink® RS only

Notes:

controls lvl 1 - zodiac pool professional access/media/80b7293a649e478c8f… · fsoft 21 notes:...

Documents