e.c. technology and efficient work fans · une‐en iso 12499. • adjustable speed by 0-10 v...

E.C. TECHNOLOGY ANDEFFICIENT WORK FANS

NEW GENERATION E.C. FANS

EFFICIENTWORK

SODECA presents its new “Efficient Work” high performance fans, fitted with next-generation motors to obtain higher energy savings.

These new products exceed the requirements of the ErP 2009/125/CE Ecodesign Directive and its regulating provisions (EU) 327/2011 for fans, and 1253/2014 for ventilation units, collaborating with the EU KYOTO Protocol objective of reducing carbon emissions.

The electronic variable speed drives (VSD) permit the fan speed to be adjusted to demand, thus obtaining extra energy savings. SODECA has a wide range of electronic control accessories for use in conjunction with the variable speed drive. Control the temperature, humidity, CO2 or pressure of your facility by adjusting the fan speed to the demand. The electronic variable speed drives (VSD) can also be connected to single or three-phase networks with an extensive range of supply voltages and frequencies.

COMPARISON OF ENERGY SAVINGS

Just replacing the fan installed with a fan fitted with E.C. technology will allow you to obtain electricity consumption savings of 21%. If in addition you install an electronic control to regulate the variable speed drive (VSD), you will have a demand controlled ventilation (DCV) system and obtain higher savings.

In the following case, a simulation is made of ventilation demand in an office block on a business day (7am-9pm), according to the "Demand Controlled Ventilation Systems" technical report set out in Annex 18 of the International Energy Agency (IEA). The energy savings obtained after replacing the conventional ventilation system in the above case with an E.C. demand controlled ventilation system is given below. The average savings percentage is 50%. Energy savings enable the excess cost of the E.C. equipment to be quickly amortised. It is a profitable option, with or without a demand control ventilation system.

% Energy100%

80%

60%

40%

20%

0% 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Hours of the day

E.C. with DCV

E.C. without DCV

No E.C.

% Savings100%

80%

60%

40%

20%

0% 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Hours of the day

E.C. with DCVvs. No E.C.

Average savings

Synchronous E.C. Industrial Brushless motors with permanent magnets, and with an efficiency that is 27% higher than their asynchronous equivalent. Also manufactured with a variable speed drive (VSD).

NEW GENERATION E.C. FANS

E.C. TECHNOLOGY AND EFFICIENT WORK FANS

HEP/EW Fan:• Airflowdirectionfrommotortoimpeller.

• Fibreglass-reinforced polyamide-6impeller.

• Sheetsteelsupportbase.• Anti-contactprotectivegrillepursuanttostandard UNE‐ENISO12499.

• Adjustablespeedby0-10Vsignalorbuilt-inautomaticcontrol.

Motor:• Newhigh-efficiency(IE4)synchronousE.C.motors. Fittedwithhigh-intensityneodymiummagnets.

• Acompact,built-inmotor andelectronicunitthat facilitatestheairflow.

• High-reliabilitymotorthatrequiresnomaintenance.

• Fittedwithdurableballbearings.

• IP65protection.• Electronicvariablespeeddrivehighlyconfigurablewith2analogueinputs,2digitaloutputs,1relayoutputandachoiceof1analogueor1digitaloutput.

• PossibilityofconnectiontoMODBUSandCANOpenfieldbuses.

• Availablewithsingle-phase220-240V50/60Hz(VSD1/Btype)orthree-phase380-415V50/60Hz(VSD3/Btype)inputs.

• Fanoperatingtemperature:-25°C+60°C.

High-efficiency wall-mounted axial fans fitted with E.C. brushless industrial motor and built-in electronics.

HFW-L/EW Fan:• Airflowdirectionfrommotortoimpeller.• Rotorsmadeofcastaluminium.• Supportringmadeofsheetsteelwithdoubleflangeandcableglandformotorpowersupply.

• Hotdipgalvanisedtubularsheetsteelcasing.• Variablespeeddrive(VSD),single-phaseorthree-phase,suppliedwithfan.


• Compactmotorstofacilitateairflow.• High-reliabilitysensorlesscontrol,whichrequiresnomaintenance.

• Fittedwithdurableballbearings.• IP65protection.• Fanoperatingtemperature:-25ºC+50ºC.

Tubular axial fans designed with four support arms to reduce vibrations and fitted with an aerodynamic aluminium low-consumption impeller and an IE4 Brushless E.C. Industrial motor.

CBD/EW Fan:• Galvanisedsheetsteelcasing.• Forward-curvedimpellermadeofgalvanisedsheetsteel.

• Adjustablespeedby0-10Vsignalorbuilt-inautomaticcontrol.

Motor:• Newhigh-efficiency(IE4)syn-chronousE.C.motors.Fittedwithhigh-intensityneodymiummagnets.

• Acompact,built-inmotorandelectronicunitthatfacilitatestheairflow.

• High-reliabilitymotorthatrequiresnomaintenance.

• Fittedwithdurableball

bearings.• IP54protection.• Electronicvariablespeeddrivehighlyconfigurablewith2ana-logueinputs,2digitaloutputs,1relayoutputandachoiceof1analogueor1digitaloutput.

• PossibilityofconnectiontoMODBUSandCANOpenfieldbuses.

• Availablewithsingle-phase220-240V50/60Hz(VSD1/Btype)orthree-phase380-415V50/60Hz(VSD3/Btype)inputs.

• Fanoperatingtemperature:-25°C+60°C.

Double inlet centrifugal fans with direct-drive motors and forward-curved impeller, fitted with E.C. brushless industrial motor and built-in electronics.

CJV/EW Fan:• Extractorfanunitswithverticalimpulsionandtwocircularextractionnozzles.

• Galvanisedsheetsteelcasing.• Forward-curvedimpeller,madeofgalvanisedsheetsteel.• Single-phasevariablespeeddrive(VSD)suppliedwithfan.

Motor• Newhigh-efficiency(IE4)synchronousE.C.motors. Fittedwithhigh-intensityneodymiummagnets.

• High-reliabilitysensorlesscontrol,whichrequiresnomaintenance.

• Fittedwithdurableballbearings.• IP55protection.• Fanoperatingtemperature:-25°C+60°C.• CJV/EW-1800/T:Fanoperatingtemperature:S1-25°C+60°Ccontinuousoperation.400°C/2hS2operation.

• ApprovedinaccordancewithstandardEN12101‐3.

Automatic operation extractor fan units with vertical air outlet, E.C. Brushless industrial motor and constant pressure control for housing mechanical ventilation (VMC).

Fan:• Acousticcasingcoatedwithphonoabsorbentmaterial.• Allmodelsfittedwithareactionimpeller.• Standardisedinletandimpulsionflangesallowingforeasyinstallationinducts.

• Fittedwithafoldinginspectioncover.• Supportfeetbuiltintothebox,foreasyinstallation.• Linearairflowdirection.• Speedcontrolledbyabuilt-in10kΩMTP010power meteroranexternal0‐10Vsignal.

Motor:• Single-phase200‐240V50/60Hz,IP54protection.ExceptmodelSVE/PLUS/EW‐400/H,200‐277V50/60Hz,IP55protection.

• Maximumtemperatureofairtobecarried:‐25ºC+60ºC.ExceptmodelSVE/PLUS/EW‐200/H,‐25ºC+45ºC.

• E.C.brushlessexternalrotormotorswithhighefficiency andbuilt-invariablespeeddrivecontrolledby0‐10Vsignal.

In-line, low noise duct fans mounted inside a 40 mm Phonoabsorbent acoustic casing.

SVE/PLUS/EW

SVE/PLUS/EW/CPC Fan:• Acousticcasingcoatedwithphonoabsorbentmaterial.• Allmodelsfittedwithareactionimpeller.• Standardisedinletandimpulsionflanges allowingforeasyinstallationinducts.

• Fittedwithafoldinginspectioncover.• Supportfeetbuiltintothebox,foreasyinstallation.• Linearairflowdirection.

Motor:• Single-phase200-240V50/60Hz,IP54protection. ExceptmodelSVE/PLUS/EW‐400/H,200‐277V50/60Hz, IP55protection.

• Maximumtemperatureofairtobecarried:‐25°C+60°C.ExceptmodelSVE/PLUS/EW-200/H,‐25°C+45°C.

• Highefficiencyexternalbrushless-E.C.motors.

Low-noise, in-line duct extractor fans for automatic operation mounted inside a 40 mm phonoabsorbent acoustic insulated casing, with constant pressure control.

ModelCJV/EW‐1800/Tapprovedfor400°C/2h


CJBD/EW

CJBD/EW/CPC

CKDR/EW

CVT/EW

Fan:• Galvanisedsheetsteelcasing.• Forward-curvedimpellermadeofgalvanisedsheetsteel.• Variablespeeddrive(VSD),single-phaseorthree-phase,suppliedwithfan.

• Speedcontrolledbyabuilt-in10kΩMTP010powermeter oranexternal0‐10Vsignal.


• Compactmotorstofacilitateairflow.• High-reliabilitysensorlesscontrol,whichrequires nomaintenance.

• Fittedwithdurableballbearings.• IP54protection.• Fanoperatingtemperature:-25°C+60°C.

Fan:• Galvanisedsheetsteelcasing.• Forward-curvedimpellermadeofgalvanisedsheetsteel.• Variablespeeddrive(VSD),single-phaseorthree-phase,suppliedwithfan.


• Compactmotorstofacilitateairflow.• High-reliabilitysensorlesscontrol,whichrequires nomaintenance.


Fan:• Galvanisedsheetsteelstructure.• 40mmacousticinsulationslab.• Reactionimpellermadeofgalvanisedsheetsteel.• ApprovedinaccordancewithstandardEN12101-3, withcertificateno.:0370-CPR-2358.

• Modifiabledooropeningdirectionthankstoitsexchangeablehinges.

• Canbeadjustedtodifferentpositions.• Abletooperatecontinuouslyat120ºC. Motor:• Newhigh-efficiency(IE4)synchronousE.C.motors. Fittedwithhigh-intensityneodymiummagnets.


• Fittedwithdurableballbearings.• IP55protection.• Fanoperatingtemperature:-25ºC+120ºC.

Fan:• Galvanisedsheetsteelsupportbase.• Impellerwithreactionblades,madeofgalvanisedsheetsteel.• Birdguard.• Aluminiumraincover.




Ventilation units with acoustic insulation, fitted with CBD/EW fans and Brushless E.C. Industrial motors.

Automatic operation extractor fan units with acoustic insulation, fitted with Brushless industrial E.C. motors and constant pressure control.

F-400 extractor fan units with a large door for each of maintenance and 40 mm acoustic insulation slab.

400 ºC/2h centrifugal roof-mounted extractor fans, with vertical air outlet, fitted with Brushless E.C. industrial motors.

CRF/EW/CPC Centrifugalroof-mountedextractfanswithlownoiselevelandexternalrotormotor,fittedwithaBrushlessE.C.industrialmotor.

Fan:• Madeofgalvanisedsheetsteel.• Impellerwithreactionbladesmadeofplasticmaterial.• Birdguard.• Foldingbodyforeaseofinspectionandmaintenance.

Motor:• HighefficiencyE.C.externalrotormotorsregulated by0-10Vsignal.

• IP54protection.• Single-phase230V-50/60Hzandthree-phase400V-50/60Hz.• Maximumtemperatureofairtobecarried:-25°C+50°C.

Roof-mounted, automatic-operation centrifugal extrac-tor fans with low noise level, fitted with external Brushless E.C. Motor and constant pressure control.

CRF/EW Centrifugalroof-mountedextractfanswithlownoiselevelandexternalrotormotor,fittedwithanE.C.Brushlessindustrialmotorandabuilt-inspeedregulatingpowermeter.

Fan:• Madeofgalvanisedsheetsteel.• Impellerwithreactionbladesmadeofplasticmaterial.• Birdguard.• Foldingbodyforeaseofinspectionandmaintenance. Motor:• NewhighefficiencyE.C.externalrotormotorsregulated by0-10Vsignal.IP54protection.

• Single-phase230V-50/60Hzandthree-phase400V-50/60Hz.• Maximumtemperatureofairtobecarried:-25ºC+50ºC.

Centrifugal roof-mounted extract fans with low noise level and external rotor motor, fitted with a Brushless E.C. industrial motor.


www.sodeca.com

HEADQUARTERSodeca S.L.U.Ctra. de Berga, km 0,7E-08580 SANT QUIRZE DE BESORABarcelona, SPAINTel. +34 93 852 91 11Fax +34 93 852 90 42General sales: [email protected] sales: [email protected]

COLOMBIASodeca Latam S.A.SSra. Luisa Stella PrietoCalle7 No. 13 A-44Manzana 4 Lote1, MontanaMosquera, CundinamarcaBogotá, COLOMBIATel. +57 1 756 [email protected]

CHILESodeca Ventiladores LtdaSr. Frederic CousquerSanta Bernardita 12.005(Esquina con Puerta Sur)Bodegas 24 a 26, San Bernado, Santiago, CHILETel. +56 22 840 [email protected]

CARIBBEAN ZONESodeca CubaResidencial MiramarApto. Nº 108, Ave. 7ma Nº 1805 entre 18 y 20, Miramar Playa, La Habana, CUBATel. +537 20 [email protected]

RUSSIASodeca, L.L.C.Mr. Stanislav AlifanovMyasischeva str, 1, room 603Business Сenter “Chaika”140180 ZhukovskiyMoscow region, RUSSIATel. +7 495 955 90 [email protected]

AMERICA

RUSSIA

FINLANDSodeca Finland OyMr. Kai Yli-SipiläMetsälinnankatu 30, PL2FI-32700 Huittinen FINLANDTel. + 358 400 320 [email protected]

UNITED KINGDOMSodeca Fans UK LtdMr. Mark NewcombeTamworth Enterprise CentrePhilip Dix House, Corporation Street, Tamworth , B79 7DNUNITED KINGDOMTel. +44 (0) 1827 216 [email protected]

PORTORua Veloso Salgado 1120/1138 4450-801 Leça de PalmeiraTel. +351 229 991 [email protected]

LISBOAPq. Emp. da Granja Pav. 8 2625-607 Vialonga Tel. +351 219 748 [email protected]

ALGARVERua da Alegria S/N8200-557 CortesõesTel. +351 913 615 [email protected]

EUROPE

PORTUGALSodeca Portugal Unip. Lda

PERUSodeca Perú SACSr. Jose Luis JiménezC/ Mariscal Jose Luis de Orbegoso 331. Urb. El pino. 15022 , San Luis. Lima, PERÚTel. +51 1 326 24 24Cel. +51 [email protected]

e.c. technology and efficient work fans · une‐en iso 12499. • adjustable speed by 0-10 v...

Documents