installation instructions - downloads.chiefmfg.comdownloads.chiefmfg.com/manuals-i/ts525tu-i.pdf ·...

I N S T A L L A T I O N I N S T R U C T I O N S

Instrucciones de instalaciónInstallationsanleitungInstruções de Instalação

Istruzioni di installazioneInstallatie-instructiesInstructions d´installation

Large Swing Arm Mounts

Spanish Product DescriptionGerman Product Description

Portuguese Product Description Italian Product DescriptionDutch Product Description

French Product Description

TS525TU

TS525TU Installation Instructions

2

DISCLAIMER

Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.

IMPORTANT SAFETY INSTRUCTIONS!

WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions.

WARNING: Use this mounting system only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.

WARNING: Never operate this mounting system if it is damaged. Return the mounting system to a service center for examination and repair.

WARNING: Do not use this product outdoors.

WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided.

WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component.

WARNING: The wall to which the mount is being attached may have a maximum drywall thickness of 5/8" (1.6cm) when installing to wood studs or hollow concrete block. If installing to poured concrete, the wall CANNOT have ANY drywall covering!

WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components attached does not exceed 125 lbs (56.7 kg). Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury.

IMPORTANT ! : The TS525TU mount is designed to be mounted to an 8" concrete, 8"x8"x16" concrete block or 2" x 4" wood studs (16" on center) wall.

--SAVE THESE INSTRUCTIONS!--

Installation Instructions TS525TU

3

DIMENSIONS

80031.496

MAX HORIZONTAL PATTERN

749.3029.500

12.50.492

7.00" [177.8]LEFT/RIGHTADJUSTMENT

100 X 100200 X 200

821.1932.330

MAX WIDTH

551.6321.718

MAX

63.502.500

.328

473.0818.625 OF

SCREEN

COLLAPSED VIEW

MAXIMUM WEIGHT CAPACITY = 125 lbs. (56.7 kg) DIMENSIONS: [MILLIMETERS] INCHES

45.000°

537.221.1

DISTANCE FROM WALLTO C/L OF MOUNT

90.000°

375.2414.773

DISTANCE FROM WALLTO C/L OF MOUNT

MAXIMUM SIDE SWIVEL

DIMENSIONS: [MILLIMETERS] INCHES


4

LEGEND

Tighten Fastener

Apretar elemento de fijación

Befestigungsteil festziehen

Apertar fixador

Serrare il fissaggio

Bevestiging vastdraaien

Serrez les fixations

Loosen Fastener

Aflojar elemento de fijación

Befestigungsteil lösen

Desapertar fixador

Allentare il fissaggio

Bevestiging losdraaien

Desserrez les fixations

Phillips Screwdriver

Destornillador Phillips

Kreuzschlitzschraubendreher

Chave de fendas Phillips

Cacciavite a stella

Kruiskopschroevendraaier

Tournevis à pointe cruciforme

Open-Ended Wrench

Llave de boca

Gabelschlüssel

Chave de bocas

Chiave a punte aperte

Steeksleutel

Clé à fourche

By Hand

A mano

Von Hand

Com a mão

A mano

Met de hand

À la main

Hex-Head Wrench

Llave de cabeza hexagonal

Sechskantschlüssel

Chave de cabeça sextavada

Chiave esagonale

Zeskantsleutel

Clé à tête hexagonale

Pencil Mark

Marcar con lápiz

Stiftmarkierung

Marcar com lápis

Segno a matita

Potloodmerkteken

Marquage au crayon

Drill Hole

Perforar

Bohrloch

Fazer furo

Praticare un foro

Gat boren

Percez un trou

Adjust

Ajustar

Einstellen

Ajustar

Regolare

Afstellen

Ajuster

Remove

Quitar

Entfernen

Remover

Rimuovere

Verwijderen

Retirez

Optional

Opcional

Optional

Opcional

Opzionale

Optie

En option

Security Wrench

Llave de seguridad

Sicherheitsschlüssel

Chave de segurança

Chiave di sicurezza

Veiligheidssleutel

Clé de sécurité


5

TOOLS REQUIRED FOR INSTALLATION

PARTS

13/64" (5.1mm) - wood studs #21/2" (12.7mm)3/8" (10mm) - concrete

concrete only

A1 (6)M4x10mm

A2 (6)M4x16mm

A3 (6)M4x25mm

B1 (6)M5x10mm

B2 (6)M5x16mm

B3 (6)M5x25mm

C1 (6)M6x10mm

C2 (6)M6x16mm

C3 (6)M6x25mm

D1 (4)M8x10mm

D2 (4)M8x20mm

D3 (4)M8x30mm

E1 (6).75x.323x.25

E2 (6).75x.344x.5

E3 (1)M5

E4 (6)[univ.washer]

F (4)5/16 x 2 1/2"

G (4)[concrete anchor] H (4)

[install. washer]

J (4)M5

K (4)M4

L (4)[shoulder washer]

M (1)[main assembly]

N (1)[wall rail]

P (1)[right upright]

Q (1)[left upright]

R (1)[top interface support]

S (1)[bottom interface support]

U (1)[knob assembly] #10-24 x 1 1/4"

V (1)W (8)

#10-24 x 1/2"5/16-18"

X (2)

Y (1)[latch spacer]

Z (1) AA (1)1/4"

BB (1)3/16"1/8"

"A"

"B"

"C"

"D"

"E"

hardwarebag

washerbag

T (2)[wall cover]

CC (2)[long adhesive]

DD (4)[short adhesive]


6

Assembly And Installation

Install Wall Plate to Wall - Wood Studs

WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. The wall to which the mount is being attached may have a maximum drywall thickness of 5/8" (1.6cm).

1. Determine mounting location. Use stud finder to locate 2" x 4" wood studs.

2. Measure 9 5/16" above desired center line and draw a horizontal line. (See Figure 1)

NOTE: Hold mount up to wall at desired mounting location if unsure about where the center line will be. The center line of the mount will coincide with the center line of the display. (See Figure 1)

IMPORTANT ! : Use a level to make sure wall rail (N) is level when mounted to the wall!

3. Drill two 13/64" holes at center of wood studs along the line drawn in the Step 2. (See Figure 1)

Figure 1

4. Loosely attach wall rail (N) to wall using two 5/16- 2 1/2" flange head lag screws (F). (See Figure 2)

5. Place two installation spacers (H) over two 5/16 x 2 1/2" flange head lag screws (F). (See Figure 2)

6. Tighten two screws (F) to secure upper wall rail (N) to wall. (See Figure 2)

Figure 2

7. Slide main assembly (M) onto wall rail (N). (See Figure 3)

Figure 3

8. Center main assembly (M) over two studs.

9. Drill two 13/64" holes in center of wood studs at lower mounting holes. (See Figure 4)

10. Loosely install two 5/16 x 2 1/2" flange head lag screws (F). (See Figure 4)

11. Place two installation spacers (H) over two flange head lag screws (F). (See Figure 4)

12. Tighten two screws to secure main assembly (M) to wall. (See Figure 4)

3

center line (M)

x 2

9 5/16

16"

(F) x 2

(H) x 2 (N)

4

6

7

(N)

(M)


7

Figure 4

WARNING: DO NOT REMOVE SPACER AS SHOWN BELOW PRIOR TO INSTALLING THE LOWER TWO LAG SCREWS OR THE MOUNT WILL FALL OFF THE WALL WHEN THE SPACER IS REMOVED!

13. Loosen two flat head cap screws on upper carriage rail in order to loosen white spacer. (See Figure 5)

14. Remove white spacer from mount. (See Figure 5)

15. Tighten flat head cap screws. (See Figure 5)

Figure 5

16. Proceed to Install Interface Bracket to Display section on page 9.

Install Wall Plate to Wall - Hollow Concrete Block or Poured Concrete (Important!- Read warnings below for drywall restrictions!)

WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component.

WARNING: The wall to which the mount is being attached may have a maximum drywall thickness of 5/8" (1.6cm) if installing to hollow concrete block. If installing to poured concrete, the wall CANNOT have ANY drywall covering!

WARNING: INSTALLING THE TS525TU INTO UNDERRATED OR DAMAGED CONCRETE CAN LEAD TO SERIOUS INJURY OR DAMAGE TO PRODUCT! When installing into concrete, only install the TS525TU into concrete at least 8" in depth or into 8"x8"x16" concrete blocks! Never install the TS525TU into cracked, chipped or flaking concrete.

1. Determine mounting location.

2. Measure 9 5/16" above desired center line and draw a horizontal line. (See Figure 6)

NOTE: Hold mount up to wall at desired mounting location if unsure about where the center line will be. The center line of the mount will coincide with the center line of the display. (See Figure 6)


3. Drill two 3/8" holes 16" apart and along the line drawn in the Step 2. (See Figure 6)

Figure 6

(F) x 2

(H) x 2

10

12

9 x 2

11

13 15

14

(N)

(M)

16”

9 5/16”

3

center line(M)

x 2


8

4. Install two concrete anchors (G) into two drilled holes. (See Figure 7)

5. Loosely attach wall rail (N) to wall by installing two 5/16- 2 1/2 flange head lag screws (F) into concrete anchors (G). (See Figure 7)


6. Place two installation spacers (H) over two 5/16 x 2 1/2" flange head lag screws (F). (See Figure 7)

7. Tighten two screws to secure upper wall rail (N) to wall. (See Figure 7)

Figure 7

8. Slide main assembly (M) onto wall rail (N). (See Figure 8)

9. Center main assembly (M) over wall rail (N). (See Figure 8)

10. Mark two holes at lower mounting holes. (See Figure 8)

11. Slide main assembly (M) off wall rail (N). (See Figure 8)

12. Drill two 3/8" holes at marked locations. (See Figure 8)

13. Install two concrete anchors (G) into drilled holes. (See Figure 8)

Figure 8

14. Slide main assembly (M) back onto wall rail (N). (See Figure 9)

Figure 9

(F) x 2

(H) x 2

(N)

5

7

(G) x 24

6

11

8

center of wall rail

x 210

(G) x 2 (with main assembly removed)13

12 x 2

(N)

(M)

14

(N)

(M)


9

15. Loosely install two 5/16 x 2 1/2" flange head lag screws (F) through lower wall rail on main assembly and into concrete anchors. (See Figure 10)

16. Place two installation spacers (H) over two flange head lag screws (F). (See Figure 10)

17. Tighten two screws (F) to secure main assembly (M) to wall. (See Figure 10)

Figure 10

WARNING: DO NOT REMOVE SPACER AS SHOWN BELOW PRIOR TO INSTALLING THE LOWER TWO LAG SCREWS OR THE MOUNT WILL FALL OFF THE WALL WHEN THE SPACER IS REMOVED!

18. Loosen two flat head cap screws on upper carriage rail in order to loosen white spacer. (See Figure 11)

19. Remove white spacer from mount. (See Figure 11)

20. Tighten flat head cap screws. (See Figure 11)

Figure 11

(F) x 2

(H) x 2

15

17

16

18 20

19

(N)

(M)


10

Install Interface Bracket to Display

IMPORTANT ! : If the displays hole pattern size is 100mm x100mm, 200mm x 200mm or 100mm x 200mm, the display can be mounted directly to the faceplate and the interface bracket DOES NOT need to be installed! Proceed to Install Display section.

1. Lay display face down on protective surface.

CAUTION: Using screws of improper diameter may damage your display! Proper screws will easily thread into display mounting holes.

2. Select screw diameter by examining hardware (A-D) (4mm, 5mm, 6mm or 8mm) and comparing with mounting holes on display. (See Figure 12)

3. Select spacers: (See Figure 12)

• If mounting holes are not recessed and both uprights (P and Q) can lay flat against display, then no spacers are required.

• If mounting holes are recessed, or if protrusions prevent uprights (P and Q) from laying flat, then spacers (E1 or E2) must be used.

CAUTION: Using screws of improper length may damage your display! Proper screws will have adequate thread engagement without contacting bottom of display mounting holes.

4. Select screw length: (See Figure 12)

• Using your hand, insert SHORTEST length screw of selected diameter (A1, B1,C1 or D1) through universal washer (E4), uprights (P or Q), selected spacer (E1 or E2, if required), into display mounting hole. Do NOT thread screw into hole at this time.

NOTE: Universal washers (E4) are not needed if using M8 button head cap screws (D).

• Proper screw length requires base of screw head to protrude above flat washer a distance equal to or greater than the screw diameter. If screw length is inadequate, select longer screw. Select shortest screw which will protrude the required distance.

5. Place uprights (P and Q) on display, ensuring: (See Figure 13)

• Center of uprights (P and Q) are as close to the center of the back of display as possible after being installed. Center of bracket is indicated by the diamond-shaped hole.

NOTE: If installing to a display with a narrow hole mounting pattern (less than 400mm wide), reverse uprights (P and Q) so that the upright legs do not overlap onto each other. (See Figure 13)

Figure 12

Figure 13

6. Using Phillips screwdriver, carefully install selected screws through universal washers (E4, if required), uprights (P and Q), and spacers (E1 or E2, if required), into display. (See Figure 12)

7. Tighten all screws. Ensure all applicable display mounting holes (4, 6, or 8) are used.

(A-C) x4,x6,x8 or

(E4) x4,x6,x8

2 4

(E1 or E2) x4,x6,x8

5

(Q)

(P)

6 (D) x4

(not needed with D)

(only with recessed holes)

(P)

(Q)

legs would otherwiseoverlap

for narrow mounting hole pattern


11

Figure 14

8. Connect top interface support (R) to uprights (P and Q) using four #10-24 x 1/2" button head cap screws (W). (See Figure 14)

NOTE: If possible install screws diagonally across from each other in order to provide maximum support in Steps 8 and 9.

9. Connect bottom interface support (S) to uprights (P and Q) using four #10-24 x 1/2" button head cap screws (W). (See Figure 14)

10. When connecting bottom interface support (S) to uprights, make sure that it is aligned vertically with top interface support (R). (See Figure 14)

Installing Display

Using Interface Bracket

WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components attached does not exceed 125 lbs (56.7 kg). Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury.

WARNING: Display may be very heavy! Ensure display can be safely lifted and maneuvered as required to install on wall plate. Failure to take adequate precautions can result in serious personal injury or damage to equipment!

1. Hang interface bracket and display to faceplate by placing two mounting buttons on top interface support (R) over two teardrop grooves on top of faceplate. (See Figure 15)

2. Secure interface bracket and display to faceplate by installing two 5/16-18" flange nuts (X) onto screws on lower interface support (S). (See Figure 15)

(W) x 48(R)

(S)

(W) x 49

10

10

(W) x 48

(W) x 49

narrow mounting hole pattern

Figure 15

1

2 (X) x 2

(R)

(S)


12

Installing Display Without Interface Bracket (100x100, 200x200 or 100x200)

CAUTION: Using screws of improper diameter may damage your display! Proper screws will easily thread into display mounting holes.

1. Select screw diameter by examining hardware (A-D) (4mm, 5mm, 6mm or 8mm) and comparing with mounting holes on display.

CAUTION: Using screws of improper length may damage your display! Proper screws will have adequate thread engagement without contacting bottom of display mounting holes.

2. Select screw length:

• Using your hand, insert SHORTEST length screw of selected diameter (A1, B1, C1 or D1) into display mounting hole. Do NOT thread screw into hole at this time.

3. Install two selected screws (A-D) into upper two holes on back of display. (See Figure 16)

IMPORTANT ! : If using M4 or M5 screws (A or B), washer hardware (J, K and L) must be used to ensure tight fit into the faceplate holes! For M4 screws (A), use M4 washer (K) and shoulder washer (L). For M5 screws (B), use M5 washer (J) and shoulder washer (L). (See Figure 16)

Figure 16

4. Hang display by two screws onto faceplate through either inner or outer teardrop mounting holes. (200x200 mounting pattern shown) (See Figure 17)

5. Secure display to faceplate by installing two selected screws (A-D) through washer hardware (J,K, and L) for M4 (A) and M5 (B) screws only, lower holes on faceplate and into lower two holes on display. (See Figure 17)

Figure 17

Wall Cover Installation

CAUTION: Wall covers are fragile and may be damaged or broken if installed with excessive force! Use caution when installing and removing wall covers.

1. Turn wall cover (T) outward to allow outside of covers to wrap around wall rail. (See Figure 18)

2. Place wall cover (T) over wall rail. (See Figure 18)

Figure 18

(A-C) x 23

(L) x2 (with A and B ONLY!)

(J) x 2 with (B)

(K) x 2 with (A)or

or

(D) x 2

(200 x 200 shown)

4

5 (A-C) x 2

(L) x 2 (with A and B ONLY!)

(J) x 2 with (B)

(K) x 2 with (A)or

(D) x 2

or

(T) x 2

12

2


13

Cable Management

1. Make all cable connections to display.

2. Open cable management covers on upper and lower swing arms. (See Figure 19)

3. Route cables on top of upper arm. (See Figure 19)

4. (Optional) Use cable ties (not included) to secure cables to upper arms by threading ties around cable and through cable tie holes on arms. (See Figure 19)

5. Close upper cable management cover. (See Figure 19)

6. Route cables under lower portion of swing arm. (See Figure 19)

7. (Optional) Use cable ties (not included) to secure cables to lower arms by threading ties around cable and through cable tie holes on arms. (See Figure 19)

8. Close lower cable management cover. (See Figure 19)

Figure 19

Creating Space (Optional)

In order to create more space between display and mount, spacers may be added.

1. Extend swing arms in order to gain access to the center support.

2. Remove flat hex-head screw holding latch to center support. (See Figure 20)

3. Place latch spacer (Y) behind latch and line with holes on center support. (See Figure 20)

4. Install #10-24 x 1 1/4" flat hex-head screw (V) through latch and latch spacer (Y) and into holes on center support. (See Figure 20)

Figure 20

5. Remove 1/2" knob assembly installed on center support. (See Figure 20)

6. Replace 1/2" knob assembly with 1" knob assembly (U). (See Figure 20)

Height Adjustment

1. Extend swing arms in order to gain access to the center support.

2. Adjust height adjustment wrench to raise or lower mount to desired height. Turn counter-clockwise to raise mount and clockwise to lower mount. (See Figure 21)

Figure 21

cable management covers

cable (typical)

2

3

8

2

cable ties(not included)4

(Y)

remove and replace with (U)

32 4

5 6

remove and replace with (V)

raise lower


14

Leveling Friction Adjustment

1. Adjust leveling adjustment screw on back of faceplate to increase or decrease leveling friction. (See Figure 22)

Figure 22

Tilt Friction Adjustment

1. Tilt display forward enough to expose screws on the side of tilting mechanism. (See Figure 23)

2. Adjust tilt friction adjustment screw to increase or decrease tilt friction. (See Figure 23)

Figure 23

Lateral Shift Adjustment

1. Remove wall rail covers (N) to expose lateral shift adjustment screws on wall rails.

2. Loosen four lateral shift adjustment screws. (See Figure 24)

3. Loosen two lower lag screws securing lower rail to the wall. (See Figure 24)

4. Slide mount laterally to desired mounting position. (See Figure 24)

5. Tighten two lower lag screws. (See Figure 24)

6. Tighten four lateral shift adjustment screws. (See Figure 24)

7. Reinstall wall rail covers (N).

Figure 24

leveling adjustmentscrew

(side view)

tilt friction adjustment screws

2 6

4

4

3 5

(swing arms not shownfor display purposes)


15

Arm Tension Adjustment1. Use 1/4" hex key (AA) to adjust arm tension at any of the

four arm tension adjustment points. (See Figure 25)

Figure 25

2. Use 9/16" wrench to adjust arm tension directly behind faceplate. (See Figure 26)

Figure 26

Install Interface Bracket Adhesive Covers (Optional)If the interface bracket was required to install display to mount, adhesive covers may be used to cover the holes on the interface bracket in order to improve the appearance.

1. Use two long adhesive strips (CC) to cover vertical uprights. (See Figure 27)

2. Use four short adhesive strips (DD) to cover horizontal upright supports. (See Figure 27)

NOTE: These strips may be cut as desired in order to fit around screws.

Figure 27

arm tensionadjustment points

not adjustablewith hex key

arm tensionadjustment points

(DD) x 4(CC) x 21

2

USA/International A 6436 City West Parkway, Eden Prairie, MN 55344P 800.582.6480 / 952.225.6000F 877.894.6918 / 952.894.6918

Europe A Franklinstraat 14, 6003 DK Weert, NetherlandsP +31 (0) 495 580 852F +31 (0) 495 580 845

Asia Pacific A Office No. 918 on 9/F, Shatin Galleria18-24 Shan Mei Street

Fotan, Shatin, Hong Kong P 852 2145 4099 F 852 2145 4477


Chief, a products division of Milestone AV Technologies

8805-002008 Rev102016 Milestone AV Technologieswww.chiefmfg.com02/16

installation instructions - downloads.chiefmfg.comdownloads.chiefmfg.com/manuals-i/ts525tu-i.pdf ·...

Documents