manual book for pattern machines

8/22/2019 Manual Book for Pattern Machines

1/127

Industrial Sewing Machine

USER MANUAL


2/127


3/127

I

CONTENT1 SYSTEM START AND STOP .........................................................................................1

1.1SYSTEMSTART ....................................................................................................1

1.2SYSTEMSTOP .......................................................................................................1

2 SYSTEM BASIC SCREEN .............................................................................................2

2.1AREADIVISIONOFMAINMENU ............................................................................2

2.2EXPLANATIONSOFMAINMENUKEYS ..................................................................2

2.3AUTOMATICOPERATIONSCREEN ........................................................................5

2.4COUNTSETTINGSCREEN .....................................................................................5

2.5MANUALOPERATIONSCREEN ..............................................................................6

2.6DEFAULTSCREENDATA .......................................................................................7

2.7SCALING\ROTATION\SYMMETRICAL .................................................................7

2.7.1 SCALING ........................................................................................................ 7

2.7.2 ROTATION ..................................................................................................... 8

2.7.3 SYMMETRICAL ............................................................................................... 9

2.8SYSTEMLOCKANDPAUSEFUNCTION ................................................................ 11

3 READING, OPERATING AND MANAGING PATTERN DATA .......................................... 13

3.1READINGANDMANAGINGPATTERNDATA ......................................................... 13

3.2CREATINGPATTERNDATA ................................................................................. 13

3.3MANAGINGDATA ................................................................................................ 17

3.3.1 COPYING DATA (DATA RENAME) ................................................................... 18

3.3.2 COPYING MULTI-DATA ................................................................................. 19

3.3.3 DELETING DATA .......................................................................................... 20

4 CREATING STITCHING PATTERN DATA .................................................................... 20

5 INPUT MODULES OF CREATING STITCHING DATA ................................................... 21

5.1BASICINPUTMETHODS ...................................................................................... 21

5.1.1 LINEAR INPUT ............................................................................................. 22

5.1.2 ARC INPUT ................................................................................................... 26

5.1.3 CIRCLE INPUT ............................................................................................. 28

5.1.4 CURVE INPUT .............................................................................................. 30

5.1.5 BROKEN LINE INPUT ................................................................................... 35

5.1.6 POINT INPUT ............................................................................................... 37

5.1.7 CODE DATA INPUT ....................................................................................... 39

5.2APPLICATIONINPUT ........................................................................................... 41

5.2.1 BACK TACKING (START/END BACK TACKING) .............................................. 41

5.2.2 BACK TACKING (OVERLAP BACK TACKING) .................................................. 43

5.2.3 MULTIPLE STITCHING ................................................................................. 44

5.2.4 OFFSET STITCHING ..................................................................................... 46

5.2.5 ZIGZAG STITCHING (WITH OVERLAP BACK TACKING) .................................. 48


4/127

II

5.3TABLEOFSTITCHINGTYPECOMBINATIONS ...................................................... 51

6 PATTERN DATA MODIFICATION ............................................................................... 54

6.1MODIFYINGTHESTITCHINGSTARTPOSITION ................................................... 55

6.2ADDINGASTITCH ............................................................................................... 56

6.3MODIFYINGTHESTITCHPOSISTION(POSITIONOFSUBSEQUENTDATAFIXED) 58

6.4MODIFYINGTHESTITCHPOSISTION(SUBSEQUENTDATAPOSITIONMOVED) .... 59

6.5DELETINGASTITCH(DELETINGTHEDESIGNATEDNO.OFSTITCHES) ............... 60

6.6MODIFYINGABLOCK1(LINEARINPUT) .............................................................. 61

6.7MODIFYINGABLOCK2(BROKENLINE,ARC,CURVELINE) ................................. 64

6.8MODIFYINGABLOCK3(ZIGZAGINPUT) .............................................................. 66

6.9MODIFYINGABLOCK4(CHANGINGTHEFEEDDATA) ......................................... 67

6.10MODIFYINGCODEDATA(ADDINGCODEDATA) ................................................. 69

6.11MODIFYINGCODEDATA(DELETINGCODEDATA) .............................................. 70

6.12MODIFYINGTHESECONDHOMEPOSITION ...................................................... 71

6.13MODIFYINGTHESTITCHINGSTARTPOSITION .................................................. 73

6.14MODIFYINGTHESPEED .................................................................................... 74

6.15BLOCKMOVEMENT(FEEDING) .......................................................................... 76

6.16BLOCKMOVEMENT(LINEAR) ............................................................................. 77

7 PATTERN DATA CONVERSION .................................................................................. 80

7.1BACKTACKINGCONVERSION ............................................................................. 82

7.2OVERLAPBACKTACKINGCONVERSION ............................................................. 83

7.3ZIGZAGSTITCHINGCONVERSION ....................................................................... 85

7.4MULTIPLESTITCHINGCONVERSION .................................................................. 86

7.5STITCHLENGTHCONVERSION ........................................................................... 88

8 PARAMETER SET (USER PARAMETER) ..................................................................... 89

9 ASSISTANT FUNCTION ............................................................................................. 99

9.1GROUPPATTERNDATAMACROPROCESSOR ...................................................... 99

9.2OUTPUTSIGNALINSPECTION ........................................................................... 103

9.2.1 OUTPUT SIGNAL ........................................................................................ 103

9.2.2 SERVO SIGNAL .......................................................................................... 103

9.3INPUTSIGNALINSPECTION .............................................................................. 103

9.3.1 INPUT SIGNAL ........................................................................................... 104

9.3.2 HOME POSITION SIGNAL ........................................................................... 104

9.4RESUMINGDEFAULTPARAMETER ................................................................... 105

9.5REDUCTION/SPAREPARAMETER ..................................................................... 105

9.6PASSWORDMODIFINGFUNCTION ..................................................................... 105

9.6.1 SETTING OPERATION DAYS ....................................................................... 107

9.6.2 MODIFYING ............................................... 107

9.6.3 MODIFYING ................................... 108


5/127

III

9.6.4 RESUMING DEFAULT SETTING OF ............ 108

9.7VERSIONCHECK .............................................................................................. 109

[APPENDIX 1] ALARMING EXPLAINATION (SYSTEM) .................................................. 110

[APPENDIX 2] APPENDIX LIST OF KEYS .................................................................... 116


6/127


7/127

1

USER MANUAL

1 SYSTEM START AND STOP

1.1 SYSTEM START

Before system starting, please confirm the power linkage. Press the power switch, the

system immediately carries out the auto-inspection. After inspection, the screen willdisplay the system Logo illustration.

1.2 SYSTEM STOP

The main manual screen as shown on the below screen.

.

Figure 1-1 Main Manual Screen

On the main menu, press to enter the parameter saving screen as shown on thebelow screen. Then cut off the whole power switch of system, and close the computer.

Figure 1-2 Parmater Saving Screen

Caution: After pressing on the main menu,the informations will be recorded as follows:Current speed , needlework numbers , bass line numbers, current file.

After pressing on the auto-process menu, the informations will be recorded as follows:Currentspeed , needlework count, bass line count, current file, X/Y zoom times, circumrotate angle.

Please Press when you use the function of needlework count or bass line count, changeneedlework pattern or needlework speed before closing the machine, until the parameters have beensaved to cut the power. Otherwise cutting power directly.

Parameter Saving Key


8/127

2

USER MANUAL

2 SYSTEM BASIC SCREEN

After displaying Logo screen, the system enters the main menu screen automatically.

2.1 AREA DIVISION OF MAIN MENU

Figure 2-1 Function Area Division of Main Menu

2.2 EXPLANATIONS OF MAIN MENU KEYS

Figure 2-2 Explanations of Main Menu Keys

Home position return will be executed. Full screen will be executed. Parameter saving key Lift or low the press foot When press this key,the screen switching into manual operation screen to

control x-y Axis moving.(Refer figure 2-3 manual operatiom screen),as show onthe below screen.

Stitching speed setting area

Stitching pattern display area

Function keyboard area

Speed up

Display currentneedle speed

Time display

display stitching pattern document

Display stitching patterndocument number

bass line countSet scaling

Auto-work count

circumrotatemirror

Speed down


9/127

P

/

lines as

Pattern data mN

Assistan

ress the

Presshow.

Pressfigure2-

managementNew pattern fil

nt function

ey to op

s the key

he key

3),as sho

e

igure 2-3

n menu s

Figure 2-

to set wh

nter aut

on the b

anual ope

reen, as

Menu Op

ther allo

matic op

low scree

ration scre

how on t

en Screen

to wind

eration s

n.

n

e below s

ines or n

reen.( E

M odDat

Param

USER

creen.

t. Allo

planatio

difying patternta exchaging

meter setting

3

ANUAL

to wind

refer to

n file


10/127

4

USER MANUAL

/ Press the key enter workpiece counter/ bass line countersetting screen. The screen as show.

/ Press the key enter zoom times setting screen. The screen asshow.

Press the key to enter circumrotate angle setting screen.The screen asshow.


11/127

5

USER MANUAL

Press the key to enter mirror setting screen. The screen as show.

Caution:When pulling on line,must ont trample and misplay trample the run switch whichmakes sartorius to run, it is dangerous. When pulling on line, must keep away from the run switch.

2.3 AUTOMATIC OPERATION SCREEN

Figure 2-5 Explanations of Main Menu Keys

2.4 COUNT SETTING SCREEN

Press / on main menu screen, and enter the count settingscreen, as shown below.

Press the key enter workpiece counter setting screen, as shown in

Speed up

Display currentneedle speed

Display stitching patterndocument number

Time display

Speed down Needle number displayand jog operation area


12/127

6

USER MANUAL

Illustration 2-6.

Press the key enter the suture counter setting screen, as shown inIllustration 2-7.

Illustration 2-6 Counter Setting Screen Illustation 2-7 Suture Counter Setting Screen

/ Press the keys to set the available/ unavailable counter. Prsss the key and cancel suspensive operation. Press the key and input the initialized value in digital input area, then

press to conform; if not input, press directly.

Press the key and input the total count in digital input area, then pressto confirm; if not input, press directly.

Caution: Before setting initialized value, set workpieces, or can not input the initialzed value intothe system.

2.5 MANUAL OPERATION SCREEN

When on main menu screen, press to enter the manual operation screen. Thenmove X_Y axis.


13/127

7

USER MANUAL

2.6 DEFAULT SCREEN DATAWhen on main menu screen, if there is no data or selecting data, the system will

display the waiting screen on pattern display area as shown on the below screen.

2.7 SCALING \ ROTATION\ SYMMETRICAL2.7.1 SCALING

[Example] The data will be enlarged (X:120%, 120%) with a fixed stitch lengthcentering on the Point H (Home position) in the following type of stitching data.

[Operation details] Selecting scaling

waiting screen

Press orto control therotate speed ofprincipal axis.

Press the direction keyto move the X-Y axis.

Display the principalaxis coder data.

Main axis rotation

Clamp lift/down

Press the key enter zoom timessetting screen.


14/127

8

USER

Setting

Return

Confir

2.7.2 RO

[Exampletype of s

[Operatio Selec

A

C

ANUAL

reducing

to main

the mod

ATION

The paitching d

n details]ting rotat

method,

enu

fy

tern willta.

ion

B

tc., and e

e rotated

ecuting

by 45ce

PSet t

with

fixed

(Hom

P

Pscree

tering o

ess

he X, Y enl

the numeri

stitch len

e position).

ess to

Displa

ess e

n,then the

the Poin

and

rgement r

c keys. (X:

th centeri

confirm.

y the new s

ter autom

ata will be

t A in the

sep

te (reducti

20%, 120

g on the

caling.

tic operati

enlarged.

followin

rately.

n rate)

)with a

oint H

n


15/127

Settin

Return

Confir

2.7.3 SY

[Exampleright stat

the rota

to main

the mod

METRIC

The lefte.

ion meth

enu

fy

L

state of t

d, etc.

e followi

g type of

Prangle

Dir

Inp(Input

Pre

Pscree

stitching

ess

setting scr

ection:

Left rotaRight rot

ut the angl

45for this

ss .

Displa

ess e

n,then the

data will

enter

en.

tion

ation

e from the

example.)

y the new

ter autom

ata will be

USER

be conver

circumrot

numeric k

ngle.

tic operati

changed.

9

ANUAL

ted into

te

ey.

n


16/127

10

USER MANUAL

[Operation details] Selecting symmetrical

Setting the symmetrical method, etc.

Return to main menu

Press enter symmetricalsetting screen.

Clearing symmetrical origin data:Delete symmetrical origin dataKeep symmetrical origin data

(Press for this example.)

Symmetrical direction:

X symmetrical data creation (Select "Xsymmetrical data creation for this example.)

Y symmetrical data creationXY symmetrical data creation

Press .


17/127

Confir

2.8 SYS

The s

stitching

user para

Wpressing

the paus

The

paramete

Wherealized

locked sc

P

the mod

TEM LO

ystem lo

machine

meter

en param

ause key

sign sign

peration

r .

parame

y pressi

reen, as s

Pause state sign

fy

CK AND

k or pau

head, acc

.

eter is set

in autom

as shown

after pa

er is set

g pause

own belo

n

PAUSE

e functio

rding to

as the no

atic runn

on the be

usse are

as the a

ey on an

w.

FUNCTI

is reali

the pause

mal switc

ng proces

low scree

realized

tomatic

y screen.

Pscree

N

ed throu

switch t

h, the pa

s. The pa

.

ased on

ock swit

The syst

ess e

n,then the

h pressin

pe set of

se functi

tern disp

the para

h, the lo

m interf

ter autom

ata will be

USER

g the pau

pause par

n can be r

ay area

eter set

ck functi

ce will d

tic operati

changed.

11

ANUAL

se key on

ameter in

ealized by

ill display

in pause

n can be

splay the

n


18/127

12

USER MANUAL

All the operatiosn are locked to protect the operators when adjusting equipment or

maintenance; after releasing the pause key, the operations are restored.

In automatic processing, when press the pause key, the system displays the pause

sign and waits for trimming.


19/127

13

USER MANUAL

3 READING, OPERATING AND MANAGING PATTERN DATA

3.1 READING AND MANAGING PATTERN DATA[Operation details]:

3.2 CREATING PATTERN DATA

[Operation details]:

The creating process is explained by the following creating process of stitching data.

Illustration 3-1 Example image

Pressing key on main menu screen and opening the menu window, as shownbelow

Select the data in data menu displayarea.

If there is not required data incurrent display area, then use

to switch. For example, when

select No. 1 data, only press No. 1

key, the system will open the data

automatically.

System opens the No. 1 datain data display area.

Trample running switch,the system carries out the

selected data.


20/127

14

USER

Settin

Aftershown on

Create

a. In

press

b. Press

and pre

ANUAL

stitch le

et stitchillustrati

pattern d

(feed) state

to confi

and ent

s to r

ngth and

length ann 3-2.

ata

Illustr

, press the

m.

r the patt

eturen.

peed

speed, p

iton 3-2 P

irection ke

rn data set

ess t

attern Data

to move

screen (Ill

Uspress

needl

Se

Pleas

speed

speed

(

Prespatt

set, and

Compiling

the neddle

stration 12

e numeric k

to s

s must be

lect speed.

set code H

Co.

C.

Coode H is th

Delete in

rn data.

nter dat

Screen

rom home

). Select

ey to input

t. The d

ithin 0.1m

ode H me

in user pa

de MD2 m

de MD1

e L means

e default s

ut

ey, and cr

creating

osition to

(straigh

titch lengt

istance be

m~12.7mm

ans high

ameter.

ans middl

eans midd

low speed.

eed.)

eate the n

screen, as

oint A, and

line input)

, and

tween

peed.

-high

le-low

w


21/127

15

USER MANUAL

c. Press direction key , the needle moves from A to B and press to confirm.

d. Press direction key , the stitch moves from B to C and press to confirm.

e. Press direction key , the stitch moves from C to D and press to confirm.

f. Press direction key , the stitch moves from D to A and press to confire. (The straight line data

of example image is realized.)

Illustration 3-3 Data Set Screen Confirming pattern.

Saving pattern data

Memo:The jogging verification mode is used for verify the pattern. Please operate according tothe illustration.

The pattern data creating screen is shown as below.

On pattern creating data screen, presskey to enter the pattern data for checking out

images, as shown in left pattern.

Use or key to reduce or amplifyimages for confirming.

After setting, press key and return topattern creating data screen.

On pattern data creating screen, press thekey to enter pattern data store screen, as shown

in left screen.

Use numeric key to inpout data number(pattern number).

Delete input After input data number (pattern number),press key to set.

Press key and reuren to pattern creatingdata screen.


22/127

16

USER MANUAL

Caution:Enter the mode only when the both display coordinates of X/Y are zero (after settingtheone input operatio). If the display coordinates of X/Y are not zero, the system will not execute the joggingerification mode.

After entering :

Memo: If the stitch is not in the last input point when returning, the stitch will move to the lastinput point automatically for conveniently creating.

Press the key to enter thejogging verification mode.


23/127

3.3 MA

Press

stitching

When

Displaof cur

AGING

key

pattern d

Copy mul

Copy or r

Delete da

Select all

Switch of

Page up.

Page dow

press a c

ay the spacerrent disk

DATA

and

ta mana

i-pattern

name the

a.

the patte

internal d

.

rtain pat

e

key o

ement sc

data at th

single da

n data of

isk (CF c

ern data

main m

een, as s

e same ti

a.

the curre

rd ) /

s shown

nu scree

own belo

e.

t disk.

external

elow, the

. The sy

.

isk (USB

number

Patter

Displacurren

USER

tem will

).

as a diffe

rn data

ay thent disk

17

ANUAL

enter the

ent color.


24/127

18

USER MANUAL

3.3.1 COPYING DATA (DATA RENAME)

On pattern data management screen, one pattern data is slected. As shown above, the

No. 13 is selected as the current data.

After setting, press to set. If there is successful operation, the screen will dispalay as shown on the below screen.

If there is unsuccessful operation, the screen will dispalayas shown on the below screen.

Use numeric key to input targetdata name. Thatis, input the name of copy data.

Use to select whether to store thesource data or not. If store resource data, the copy

function is realized; if delete source data, the rename

function is realized.

Use to select the target disk of copydata. If select local PC memory, system stores the

copied data in system internal memory; if select

external memory, the system stores the coped data in

USB.


25/127

3.3.2 CO

Thisshown on

The N

press

If the sin the inte

internal m

the right i

If the sin the exte

external m

as the righ

principle.

file, the s

YING M

unction cthe belo

o. 1, No.

key to e

lected dat

nal memor

mory.),the

age in screen.

e screen ar

( sig

tion is sug

copy> scree

the ho

ver the ho

; when th

of local P

25, and N

copy> sc

e stored

is the

sted as

e stored

is the

ested

n.

onymic d

monymic

re is not,

C. Select

o. 39 dat

een.

ata. That

data. Tha

the syste

the data

in scree

is, obey

is, when

m will co

Dispdata

USER

ou want

are selec

the whol

there is h

y.

play the sela

19

ANUAL

o copy as

ed. Then,

coverin

monymic

ected


26/127

20

USER MANUAL

3.3.3 DELETING DATA

Press the data keys which need to be deleted. After selecting, press key to enter

screen.

4 CREATING STITCHING PATTERN DATA

The pattern input setting is involved in the process of creating stitching pattern.

Press one of four keys above, the system will enter the set screen as shown on the

below screen.

Set multiple/ offsetSelect input methods

Set zigzag

Set stitch multiple back tacking

Set back tacking sewing

Input method setting key

Pattern display area

Press to set the deletion.

Jogging in creting mode

Alter the creating speed. Low speed

Medium speed High speed

(Alter the speed value inparameter module)

Absolute coordinate


27/127

21

USER MANUAL

1 [Set Input Method] Includes point input, linear input, broken line input, circleinput, arc input, and curve input.

2 [Set Multiple/ Offset] Includes non setting, multiple sewing (feed), reversemultiple (feed), multiple sewing (sewing), reverse multiple (sewing) and offset input.

3 [Set Zigzag Input] Includes zigzag input and setting no zigzag.

4 [Set Back Tacking Sewing] Includes setting no tacking, back tacking sewing andmultiple back tacking stitch.

5 INPUT MODULES OF CREATING STITCHING DATA

Caution:By removing the presser bar lifting in pattern data input, data can be input more accurately.If key is pressed, the needle will return to home position when it is at the UP position.(If the needle is not at the UP position, it will not return to home position.)

5.1 BASIC INPUT METHODS

Key Function Explanations

Feed Feed functionPoint The Point can be input one stitch at a time.(The distance between the points must be within 12.7mm.)Linear 2-point input: A linear line is created between the current position(already input) and the newly input point.

Arc 3-point input: An arc, passing through the current position (alreadyinput) and two newly input points is created.Circle 3-point input: A circle, passing through the current position (alreadyinput) and two newly input points is created.

Brokenline

A broken line connecting the current position (already input) and theinput point (up to 63 points possible) is created.

CurveA curve passing through the current position (already input) and theinput point (up to 127 points possible) is created.


28/127

22

USER

5.1.1 LIN

[Operati

1) D

2) In

in

[Exampl

[Operatio

Press

Setti

ANUAL

AR INP

n points]

signate li

put two p

ut) and t

] The foll

n details]

key

g stitch l

T

ear inpu

oints:A li

e newly

wing typ

n the mai

ength an

Feed

ear line

nput poin

of patte

n menu s

speed

s created

t.

n data wi

H

reen

PrThe s

open

Uspress

needle

Sel

code

Co

Hom

Linear input

between

l be creat

ess an

titch lengt

.

numeric k

key t

s must be

Delete inp

ect speed.

Code

in user pa

Code

Code

Code

de H is the

me position

the curre

d.

B

d o

and speed

y to input t

set. (Th

ithin 0.1m

ut

H means h

ameter.

MD2 mean

MD1 mean

L means lo

default spe

t positio

the menu

setting scr

he stitch le

distance

~12.7mm)

gh speed.

middle-hig

middle-lo

speed.

d.

(already

screen.

en will

gth, and

between

.

lease set

h speed.

speed.


29/127

23

USER MANUAL

Setting feed modes

Pattern data drawing screen

Switching input method setting

Pattern data setting screen

Setting Point A position

Selecting the stitching input

Inputting stitching from Point A to Point B

Press . When modify the stitch length, pressto enter the stitch length setting screen.

Press key and select feed mode toinput.

When the key pointing to thefeed input, press key to set and return

to the pattern data drawing screen.

Press the direction key s and moveneedle form home position (H) to Point A.

Check the remove amount. Press key to set Point A. Press to enter input modeselecting screen.

Press to select linear input. When the key pointing to thelinear input, press key to return to

the pattern data drawing screen.

Select input method


30/127

24

USER MANUAL

Confirming pattern

Pattern confirming screen

Caution: When returning to the creating screen, the needle returns to the last input point at thesame time. (Point B)

Storing pattern data

Press key to set the creating speed: Creating speed 1 Creating speed 2 Creating speed 3

(Set creating speed in user parameter. )

Press the direction key s and move needle formPoint A to Point B.

Press key to set Point B.

After set Point B without storing thepattern data, press the key and enter

the pattern data confirming screen.

Press key to confirm needle movementpositions.

After confirming, press key to close theconfirming screen and return to creating

screen.


31/127

25

USER MANUAL

Running pattern data

Press key to return to zero. Press key, and the sewingmachine carries out the jogging. Press the

figure display area or trample the

operation switch to operate the pattern

data automaticall .

If the data is correct, press the key onpattern data drawing screen and open the data

number input screen. (As shown on the below

screen)

If the data is wrong, press key and returnto the main menu for recreating, or store the

data at first, then enter the modifying module to

modify. (Refer to section [6] pattern data

modification.)


32/127

26

USER MANUAL

5.1.2 ARC INPUT

[Operation Points]

1Set arc input. ( )2Input three points (An arc, passing through the current position (already input)

and two newly input points, is created.)

[Example] The following type of pattern data will be created.

[Operation details]

steps are the same as the linear input. Please refer to Linear input. Setting the Point A position

Selecting arc input


A

B

C

H


Check the remove amount. Press key to set Point A.

Press key to input.When the key pointing to the arcinput, key is pressed to set and return


Feed

Arc input


33/127

27

USER MANUAL

Confirming pattern


Caution: When returning to the creating screen, the needle returns to the last input point at thesame time. (Point C)

Press the direction keys to remove needlefrom Point A to Point B.

Confirm the remove amount. Press key to determine Point B. Press the direction key to remove needlefrom Point B to Point C.

Press key to set Point C input. Press key to confirm the drawing arc.After set ing, the system will return to the

pattern data drawing screen.

After setting Point C without storing thepattern data, press the key and enter


Press key to confirm the needlemovement positions.

After confirming, press key to close theconfirming screen and return to creating screen.


34/127

28

USER MANUAL

Storing pattern dataMemo:

1The three points confirm circle should be obeyed by arc input rule, or the system will operatelinear input.2The difference explanation of input point and actual stitch length figure is based on

or .For instance, when made the 15mm half circle data, it likes the below figure.

The data is made according to the specified stitch length; it is not matched that sewing point and

input point (B). There is difference (l) of the figure below because the value is calculated with thesewing point.

5.1.3 CIRCLE INPUT

[Operation Points]

1)Set arc input ( ).

2)Input threPoint Es (A circle, passing through the current position (already input)

and two newly input points, is created.)

WARNING:When circle data is created, the needle returns to the circle home position. Care stitchpositin in avoiding hand harm or danger.


A

B

C

H

A

B

C

H

Actual sewing point

B

Differencel

Actual input point

Actual sewing point


35/127

29

USER MANUAL

[Operation details]

steps are the same as the linear input. Please refer to Linear input. Setting Point A position


Inputting stitching from Point B to Point C

Confirming pattern

Press key to enter the pattern settingscreen. Select key to input.

When the key pointing to the arcinput, key is pressed to set and return


Press the direction key to remove needlefrom Point A to Point B.

Confirm the Remove amount. Press key to set Point B. Press the direction key to remove needlefrom Point B to Point C.

When set Point C, the stitches removes toPoint A automatically to realize circle input.

Press the direction key s and move needleform home position (H) to Point A.


When set Point C, the stitch returns to the Point A. Care stitch positin in avoiding hand harm ordanger.


36/127

30

USER MANUAL



Caution:The three points confirm circle should be obeyed by arc input rule, or the system willoperate linear input.

5.1.4 CURVE INPUT

[Operation points]

1Set curve input ( ).2Up to 127 points can be input (A curve, passing through the current position and

the input points, is created.)

3Press . A delimiter point can be inserted at a pointed corner to continuouslyinput the curve.

4 Caution: The delimiter point is the start point of the new curve. 5When input curve, Returning to home position key is unavailable to avoid input

error.


AB

C D

E

F

G

J

K

H

I

Press the key and enter the patterndata confirming screen.


After confirming, press key to closethe confirming screen and return to creating

screen.


37/127

31

USER MANUAL

Analysis: The above pattern consists of 2 curves. Point F is the delimiter point. Press

to set Point A, Point B, Point C, Point D, and Point E. Press to set Point F, and

press to set Point F as a delimiter point as the end of the curve input.

[Operation details]

Setting Point A posistion


Caution:Because the curve input is different from the other inputs. Therefore, key is added oncurve data drawing screen to ensure the input end.

Inputting stitching from Point B to Point F



Press key to enter the pattern settingscreen.

Select key to input.

When the key pointing to the curveinput, key is pressed and return to the



Confirm the remove amount. Press key to set Point B. Press the direction key to remove needlefrom Point B to Point C.

Press key to set Point C.Press the direction key to remove needle fromPoint C to Point D, E and F. After inputting Point F, press key to setthe curve input end. Because system can not

correctly deal with the delimiter point.


38/127

32

USER MANUAL

Inputting stitching from Point F to Point J

Caution: Press to confirm the end of curve input. Then the pattern will be displayed on thescreen.

Confirming pattern


Caution: When returning to the creating screen, the needle returns to the last input point at thesame time. (Point J)

Press the direction key s and move needlefrom Point F to Point G.

Confirm the remove amount.Press key to set Point G.Press the direction key to remove needlefrom Point G to Point H.

Press key to set Point H. Press the direction key to remove needlefrom Point H to Point I and J.

Press key to set Point J.Press key to set the curve input.

After set Point J without storing thepattern data, press the key and enter the

pattern data confirming screen.

Press key to confirm needlemovement positions.

After confirming, press key to close theconfirming screen and return to creating

screen.


39/127

33

USER MANUAL


Caution: If the distance between the curve start point and the end point is less than 0.5 mm, thepattern will be closed pattern automatically. Press key twice at the same point is regarded as theinvalid operation.


40/127

34

USER MANUAL

Keys for curve input

1Ellipse inputFor shape data as shown below, except peak, in each quadrant five or more pointss are

inputted.

2CurvePay attention to the following situations. If the curve rate changes variably, more

points need to input. For shape data (linear line+ arc) as shown below, at least input fivepoints in delimiter point.

3Arbitrary curve

If the curve rate changes variably, as Point A/B/C shown above, input points as manyas possible (more than five Points); if the curve rate is steady (Point D), input less points.For the curve drawing precision, input points as many as possible in proper conditions.4For shape data as shown below, continuous curve input is possible by selecting adelimiter point where the corner is pointed (Point F).

C

D

B

A

F

F

F

F


41/127

35

USER MANUAL

5.1.5 BROKEN LINE INPUT

[Operation points]

1Set broken line input ( ).2Up to 127 points can be input (A broken line connecting the current position and

input points is created.)3When input broken line, returning to home position key is unavailable.


[Operation details] Setting Point A position


Caution: Because the curve input is different from another kinds of input, therefore add oncurve creating screen to ensure the end of curve input.

Press key to enter the pattern settingscreen. Select key to input.When the key pointing to the curveinput, key is pressed and return to the


A

B

C

H

D

E

Press the direction keys and moveneedle form home position (H) to Point A.

Check the remove amount.Press key to set Point A.


42/127

36

USER MANUAL

Inputting stitching from point B to Point E

Caution: Polygon input is similar with the curve input. Press to set common points. When setend point, press and to confirm the end of polygon input. When end of polygon input, press

to see the creating pattern.

Confirming pattern


Press the direction keys and move needleform Point A to Point B.

Press key to set Point B. Press the direction keys to remove needlefrom Point B to Point C.

Press key to set Point C. Press the direction keys to remove needlefrom Point C to Point D.

Press key to set Point D. Press the direction keys to remove needlefrom Point D to Point E.

Press key to set Point E. It is the endpoint of the pattern. Then, press the

key again to set the pattern.

After set Point E without storing thepattern data, press the key and enter



After confirming, press key to close theconfirming screen and return to creating screen.


43/127

37

USER MANUAL

Caution: When returning to the creating screen, the needle returns to the last input point at thesame time. (Point E) Storing pattern data

5.1.6 POINT INPUT

[Operation points]

1Set Point E input ( ).[Example] The following type of pattern data will be created.

[Operation details] Setting Point A position


Memo: The distance between the points must be within 12.7mm.

Press key to enter the patternsetting screen. Select key to input.

When the key pointing to thecurve input, press key to set and

return to the pattern data drawing screen.

AB C

ED

F

G

I JK L

M N

Press the direction keys and moveneedle form home position (H) to Point A.



44/127

38

USER MANUAL

Inputting stitching from point B to Point N

Confirming pattern


Caution: When returning to the creating screen, the needle returns to the last input point at thesame time. (Point N) Storing pattern data



Press the direction key to remove needle fromPoint B to Point C.

Press key to set Point C.Input point from C to N separately in the samemanner as shown above.

Press key to confirm pattern, then returnto pattern data drawing screen after confirming.

After set Point N without storing thepattern data, press the key and enter


Press key, so the needlemovement positions can be confirmed.

After confirming, press key to close

the confirming screen and return to creating

screen.


45/127

39

USER MANUAL

5.1.7 CODE DATA INPUT

[Operation points]

1Designate code data input ( ).2Select code data according to the below list.

Code abbr. Function

TRIM Thread trimming

USTP Needle UP halt

DSTP Needle DOWN halt

2HP 2nd home position

BAT Basting

[Example]: As the following type of pattern data, insert between two straightlines.

[Operation details]





Press key to enter the patternsetting screen. Select key to input.

When the key pointing to thecurve input, key is pressed to set e

and return to the pattern data drawing

screen.


46/127

40

USER MANUAL

Inputting stitching from point B to Point C

Inputting the code data at the Point C (USTP)

Selecting USTP

Inputting a linear line from Point C to Point D and from Point D to Point E


When needle stops at Point C, codedata is inputted and the key is

pressed

Press key. Press to set the code. (The"NEEDLE UP HALT" code will be created.)

The system will return to the arrow input

screen.

Press the direction key s and move needle

form Point A to Point B.

Confirm remove amount.


Press the direction key to remove

needle from Point B to Point C.

Press key to set Point C.

Press the direction key s and moveneedle form Point C to Point D.

Confirm the remove amount. Press key to set Point D.Press the direction key to remove needlefrom Point D to Point E.

Press key to set Point E.


47/127

41

USER MANUAL

5.2 APPLICATION INPUT

Various types of stitching, including start/end back tacking, terminal reinforcing,

multiple stitching, offset stitching and zigzag stitching can be inputted. Various types of

stitching data can be created easily by combining the basic inputs and these types.

Caution: The back tacking, multiple stitching, offset stitching and zigzag stitching input cannot becombined with point inputs to input data.

Function Explanations

Backtacking

Start/end back tacking

Overlap back tacking

Multiplestitching

Multiple stitching (Feed data specifications)

Multiple stitching (stitching specifications)

Reverse multiple stitching (feed data specifications)

Reverse multiple stitching (stitching specifications)

Offsetstitching

Zigzagstitching

5.2.1 BACK TACKING (START/END BACK TACKING)

[Example] With the linear input, the N mode and 3-stitch back tacking will be inserted forboth the start and end of stitching. (The bold sections indicate start/end back tacking.)

A B

H

[Operation details]





48/127

42

USER MANUAL

Setting the input method

Setting the back tacking details

Inputting stitching from point A to Point B

Saving pattern dataMemo:

1Regarding back tacking modeV mode: Back tacking will be performed only once.N mode: Back tacking will be performed twice.M mode: Back tacking will be performed third.N mode: Back tacking will be performed fourth.2Regarding number of stitches

Press the key or key, and use numeric key to input back tacking stitches.

Set the feed data from the home position tothe point A with the procedures for linear

input, and open the input method setting

screen.

Press linear input .Press back tacking . Press the back tacking details setting key

.

The details are set on this screen.The details set here are (start/end back

tacking), start key (N mode). Press

key to set start stitch, and use numeric key to set

three start stitches.

Start key (N mode), press keyand use numeric key to set three end stitches.

Press . Return to input method setting screen. Press

Press the direction key s and moveneedle form Point A to Point B.

Confirm the remove amount. Press key to set Point B.


49/127

43

USER MANUAL

5.2.2 BACK TACKING (OVERLAP BACK TACKING)


A B

CD

H

Caution: It is a shutting figure in the figure made in [Broken line], [Circle], [Arc], [Curve] to be ableto do multiple back tacking.[Operation details] Setting Point A position Setting the input method

Setting the multiple back tacking details

Inputting stitching from point B to Point D

Input a rectangle as a broken line, and then

insert overlap back tacking at the end. (The overlap

mode is entered once; three overlap stitches are

made.)

Set the feed data from the home position tothe Point A with the procedures for broken line

input, and open the Input Method Setting screen.

Press broken Line Input . Press overlap back tacking .Press the back tacking details setting key .

The details are set on this screen.The details set here are, (overlap back

tacking), overlap mode , three overlap

stitches.

Press to set. The system will return to the input methodsetting screen.

Press to determine these set values. The system will return to the pattern datadrawing screen.


50/127

44

USER MANUAL

Saving pattern data

Caution:1The number of overlapped sections

, , , in the overlap mode indicate the number of overlapped sections.2Number of overlap stitches

This is the number of stitches at the overlapped section. (Set a value between 0 and 9.)

5.2.3 MULTIPLE STITCHING

Type Mode Key Stitching dataimage Explanations

Multiple

Feeddata

"Stitching" in a setdirection isconnected with"feed without stitching".

Stitching"Stitching" in a setdirection is connected with"stitching".

Reversemultiple

Feeddata

"Stitching" in alternatingreverse directions isconnected with "feed data".

Stitching"Stitching" in alternatingreverse directions isconnected with "stitching".

Caution: ( ) in the image indicates "feed data". ( ) in the image indicates "stitching".

Press the direction key s and move needleform Point A to Point B.

Press key to set Point B. Press the direction key to remove needlefrom Point B to Point C. Press key to set Point C. Press the direction key to remove needlefrom Point C to Point D.

Press key to set Point D.


51/127

45

USER MANUAL

[Example] The following type of pattern data will be created.A B

H

6mm

Create the linear reverse multiple (stitching specification) data. (The multiple distance is 6mm, the

number of times is three, the direction is right.)

[Operation details] Setting the Point A position Setting the input method

Setting the reverse multiple stitching details


Press linear input key . Press reverse multiple (stitchingspecifications) .

Press the reverse multiple details key .Set the reverse multiple stitching details.

Select the multiple mode, and press key(reverse multiple (sewing)). Select the multiple

directions, and press key (right side). Press

key, set the distance to 6.0 by using

numeric key; press key, set the

number of times to 3 by using numeric key.

After inputting the details, press to setthe data.

Press key screen to return to patterndata drawing screen.

Press the direction key s and moveneedle form Point A to Point B.

Confirm the remove amount.


52/127

46

USER MANUAL

Saving pattern dataMemo:

1DirectionWhen creating multiple stitching to the left of the input stitching line, press key (left

side).

When creating multiple stitching to the right of the input stitching line, press key

(right side).

2DistanceThis is the distance between the multiple stitching and adjacent line. Set between 0.0mm

and 20.0mm. To input the distance data, press the DISTANCE key, then use the numeric key.

3Number of timesSet the number of multiple stitching layers. Set between 2 and 9. To input the number of

times, press the DISTANCE key, then use the numeric key.

5.2.4 OFFSET STITCHING

[Example] The following type of pattern data will be created. Input offset stitching with

overlap back tacking as a broken line. (Set the offset distance to "6.0 mm", and direction

to "right".)B

6.0 mmH

A

CD

[Operation details]

Setting the Point A position Setting the input method

Press key to enter the pattern settingscreen. Select key to input.

When the key pointing to the curveinput, key is pressed and return to the


Press (offset stitching) Press the offset stitching details key .


53/127

47

USER MANUAL

Setting the offset details

Pattern stitching

Confirming and saving pattern data

The details are set on this screen.Press , and . Press key,

and use numeric key to set the distance to 6.0.

After inputting the details, press to set thedata.

press key (left side)press key (right side)

Press key to return to input methodsetting screen

Press the direction keys to remove needle fromPoint A to Point B.

Press key to determine Point B. Press the direction keys to remove needle fromPoint B to Point C.

Press key to determine Point C. Press the direction keys to remove needle fromPoint C to Point D.

Press key to set Point D. It is the end pointof the pattern. Then, press the key again to

set the pattern.


54/127

48

USER MANUAL

5.2.5 ZIGZAG STITCHING (WITH OVERLAP BACK TACKING)

[Example] The following type of pattern data will be created. Input zigzag stitching with

overlap back tacking as circle. (The zigzag deflection width will be 5.0mm the feed

amount (stitch length) will be 3.0mm, the direction is left, the overlap back tacking mode

will be carried out once, and two overlap stitches will be made.)

A H

The bold section is the overlap back tacking section.

[Operation details]

Setting the Point A position Setting the zigzag input

Setting the zigzag details

Setting the multiple back tacking details

Set the feed data from the home position Hto the point A with the procedures for broken

line input, and open the input method setting

screen.

Press circle input key . Press key to change the stitch length,

enter the stitch length screen and use

numeric key to input stitch length.

Press zigzag key . Set the application input details. Press .

The details are set on this screen.Press zigzagkey, and use numeric

key to set the deflection width to 5.0.

Press key to set deflection direction

(left side).

After inputting the details, press toset the data.


55/127

49

USER MANUAL

Circle stitching

Saving pattern data

Memo:1) The zigzag deflection width can be set in 0.1mm increments between 0.1 and 10.0mm.)2) The zigzag feed amount can be set in 0.1mm increments between 0.5 and 10.0mm.)3) Deflection width, feed amount and creation direction (feed amount= stitch length)

Press multiple back tacking key . Press .

Carry out circle stitching according to5.1.3.

Press key to confirm circle pattern.After confirming, return to pattern data

drawing screen.

The details are set on this screen.The details set here are, , overlap

mode , two overlap stitches.

After inputting the details, press toset the data.

feed amount

deflection width


56/127

50

USER MANUAL

Direction

When the direction of making is made "Center" , does not become a zigzag pattern data if "widthof the shake" is 0.1mm. Please set "width of the shake" to 0.2mm or more, or whether to do the directionof making is other then "center".


57/127

51

USER MANUAL

5.3 TABLE OF STITCHING TYPE COMBINATIONS

Basic input Application input

MultipleReversemultiple

Offset ZigzagStart/end

back tackingOverlap backtacking

Linear

Arc

Circle


58/127

52

USER MANUAL

Curve

Broken line


59/127

53

USER MANUAL

Point Combination inputs with application inputs are not possible.

Combined pattern

Multiple

Reverse ultiple

Offset

Zigzag

Start/end back tacking

Overlap back tacking


60/127

54

USER MANUAL

6 PATTERN DATA MODIFICATION

Entering the modification mode

Main modification mode functions

Function Key Details Details setting

stitch

Movement to

stitching start

position

The stitching start position

moves.

Stitch additionData for one stitch is added at

designated position

Delete Deletes the designated stitch.

Stitch position

modification

The position of thestitch is

modified

fixed

Relative movement

Block movementData in a designated range is

moved.

Change

Add new stitch in between

Block modification

The area between two points tobe modified is modified with

linear, broken line, arc, curve,

zigzag or feed data.

Second home

position

modificatino

Only use in the pattern with the

second home position.

CodeCode data is added to or deleted

from designated stitch position.

Add

Delete

Press key and key on themain menu screen to enter the modification

function.


61/127

6.1 MO

[Example

Point B a

[Operatio Enteri

Select

Cauti

when the n

Movin

IFYING

The stitc

shown b

n details]g the mo

ng the sti

on : The woeedle is low

to the m

A

THE STI

ing start

low.

ification

tching st

ork holder wered, etc.

odificatio

H

TCHING

position

mode

rt positio

will automati

n positio

START

oint A in

directio

ically move t

Prscreen

Prekey

POSITI

he stitchi

key

to the Point

ss a

to enter th

s the stitc

.

H

N

ng data wi

A stitching s

d

modificati

ing start p

A

USER

ll be modi

start position

on main

on mode.

osition dire

55

ANUAL

ied to the

n. Take care

enu

ction

e


62/127

56

USER MANUAL

Caution:The work holder will automatically move to the home position. Take care when theneedle is lowered, etc. Confirming pattern data

Caution:If there is the second home position in original data, the second home position will bedeleted after modifying stitching start position. Please reset the second home position.

6.2 ADDING A STITCH

[Example] The required stitch length B' will be added to the B point of the following typeof stitching data.

H

A B C D E F G

[Operation details] Selecting stitch addition

Press to set. Return to pattern datadrawing screen.Press key to return to

modify start point again.

Press key or key to reduce oramplify pattern.

Before setting, When is pressed, themodifications executed last will be undone.

Press the direction key s to move theposition to the point B.

Press . If is pressed before setting, the screenwill change to the previous screen.

A B BC D E F G

H


63/127

57

USER MANUAL

Determining the addition position

Setting adding stitch

Confirming pattern data

Press and to enter themodification mode.

Press stitch add key to enter the stitchadd setting screen.

Using Jog key / , determine theposition to be added. Move to the addition

position (point B). Press .

Press to set. Return to pattern datadrawing screen.

Press key or key to reduce oramplify pattern. Then, confirm the pattern.

Before setting, When is pressed, theadditions executed last will be undone. Return

to the previous screen


64/127

58

USER MANUAL

6.3 MODIFYING THE STITCH POSISTION (POSITION OF SUBSEQUENT

DATA FIXED)

[Example] The D point in the following type of stitching data will be moved. (The E, F andG points will not be changed)

H

A B C D E F G

H

A B C

D

E F G

[Operation details] Selecting stitch position modification

Determining the modification position

Setting the modification method and modification amount

Press and on main menuscreen to enter the modification mode.Press stitch position modification key

.

Using Jog / , determine theposition to be added. Move to the

modification position (point D).

Press to confirm.

To set the method, press (pattern dataafter modification stitch fixed), and move to

the modification position (point D) using the

direction key s. As shown on the above screen,

move up 3.1 from the previous Point D.

Press to set. (The stitch position wille modified.)


65/127

59

USER MANUAL

Confirming the pattern data after modifying the stitch position6.4 MODIFYING THE STITCH POSISTION (SUBSEQUENT DATA

POSITION MOVED)

[Example] The Point D in the following type of stitching data will be moved.(The E, F andG points will move)

H

A B C D E F G

H

A B C

D E F G

[Operation details] Selecting stitch position modification

Determining the modification position

Press and on main menu screen toenter the modification mode.

Press stitch position modification key .

Using jog / , determine theposition to be added. Move to the

modification position (point D). Press

key to confirm the modification position

(point D), as the screen shown below.

Press .



Before setting, when is pressed, themodifications executed last will be undone.

Return to the previous screen.


66/127

60

USER MANUAL

Setting the modification method and modification amount

Confirming the pattern data after modifying the stitch position6.5 DELETING A STITCH (DELETING THE DESIGNATED No. OF

STITCHES)[Example] The Point E between the Point D and Point F in the following type of stitchingdata will be deleted.

H

A B C D E F G

[Operation details] Selecting deletion of stitches

Determining the deletion position

To set the method, press (patterndata after modification stitch fixed), and

move to the modification position (Point

D') by using the arrow mark keys.

Press to set. (The stitch position

will be modified.)

Press and on main menuscreen to enter the modification mode.

Press stitch deletion key .



Before setting, when is pressed, themodifications executed last will be undone.


A B BC D E F G

H


67/127

61

USER MANUAL

Setting the deletion stitch

Confirming the pattern data after deleting one stitch.

6.6 MODIFYING A BLOCK 1 (LINEAR INPUT)[Example] The section between the point A and point B of the following type of stitchingpattern will be modified to a linear line.

A B

H

A B

H

[Operation details] Selecting block modification

Using jog / , or / ,determine the position to be added. Move to

the addition position (Point B).

Press .

The second point in this figure is thedeletion stitch .

Then press to confirm. (1 stitchof data will be deleted.)


Press key or key to reduce oramplify pattern. Then, confirm the pattern. Before setting, when is pressed, thedeletions executed last will be undone.



68/127

62

USER MANUAL

Determining the block modification range (start point)

Determining the block modification range (end point)

Caution:When the end point is determined, the work holder will automatically return to thestart point. Take care when the needle is lowered, etc. Selecting the input type


Press block modification key .

Press jog / , and move needle tothe Point A (start point).

Press .

Press jog / , and move needleto the Point B (end point).

Press .

Press linear .Use numeric key to input stitch length.Press to set the data.


69/127

63

USER MANUAL

Confirming the data creation

Confirming the modified data

Memo:1. When arc modification is selected for block modification: Arc modification will be executed just byindicating one point in the designated range.2. When linear modification is selected for block modification: The modification range will be connectedwith linear lines.3. If the block to be modified contains code data, the code data will be deleted.4. The block modification start point and end point are explained below.

For modification other than feed data modificationThe start point can be designated when the stitch is stitching data.The end point can be designated when the section before the stitch is stitching data.

The broken line denotes feed data, and the real line denotes stitching.

Start point End poin Designation validit y Valid (OK) Valid (OK) Invalid (NG)Prior section is feed data Invalid (NG)Prior section is feed data

Valid (OK)

For feed data modificationThe start point can be designated when the stitch is stitching data or feed data.The end point can be designated when the section before the stitch is stitching data or feed data.

(The data between the start point and end point is irrelevant.)

Press to set data


70/127

64

USER MANUAL

6.7 MODIFYING A BLOCK 2 (BROKEN LINE, ARC, CURVE LINE)

[Example] The Point C and Point D in the following type of data are each modified to thePoint C' and Point D'.

A

B

C

D

E

H

A

B

C`

D`

E

H




Caution:When the end point is determined, the work holder will automatically return to thestart point. Take care when the needle is lowered, etc.



Press Jog / , and move needle tothe Point B (start point).

Press .

Press jog / , and move needle tothe Point E (end point).

Press .


71/127

65

USER MANUAL

Selecting the input type

Moving and setting the modification origin jog position

Moving and setting the Point D` position


Press broken line .Use numeric key to input stitch length.Press to set the data.

Use direction key and move needle toPoint C`( the position to be modified) Press .

Use direction keys and move needle to PointD`. ( the position to be modified)

Press .If there are several positions to be modified,repeat steps . The number of input points willincrease.

After determining modified Point D positions,press . The system connects Point D and

Point E automatically.

Press to set. (The block position will bemodified.)


72/127

66

USER MANUAL

Caution:The work holder will automatically return to the start point. Take care when the needle islowered, etc. Confirming the modified data

6.8 MODIFYING A BLOCK 3 (ZIGZAG INPUT)

[Example]The section between the Point C and Point D in the following type of stitchingdata is modified to a zigzag pattern.

A B

A B






Press jog / , and move needle tothe Point A (start point).

Press .


73/127

67

USER MANUAL

Caution: When the end point is determined, the work holder will automatically return to the startpoint. Take care when the needle is lowered, etc. Selecting the input type

Moving and setting the modification origin jog position

Confirming the modified data6.9 MODIFYING A BLOCK 4 (CHANGING THE FEED DATA)

[Example] The Point C and Point B in the following type of data are each modified to thePoint C' and Point B'.

A B

H

C

A B'

H

C`


Press zigzag . Use numeric key to input deflectionwidth, feed amount and creation direction.

(Refer to "5.2.5 zigzag stitching (with

overlap back tacking)" for details on the

deflection width, feed amount and creation

direction.)

Press to set the data.

Press .

Press jog / , and move needleto the Point B (end point).

Press .


74/127

68

USER MANUAL



Caution:When the end point is determined, the work holder will automatically return to the startpoint. Take care when the needle is lowered, etc. Selecting the input type



Press and .

Press jog / , and move needle tothe Point C (start point).

Press .

Press jog / , and move needle tothe Point B (end point).

Press .


75/127

69

USER MANUAL


Caution:The work holder will automatically return to the start point. Take care when the needle islowered, etc.

6.10 MODIFYING CODE DATA (ADDING CODE DATA)

[Example] The needle UP halt code (USTP) will be added to the Point D of the followingtype of stitching data.

A B C D E F

H

[Operation details] Selecting code data addition

Determining the code addition position

Press to set. (The block position wille modified.)


Press code data change key andenter the next setting screen

Press jog / , and move needle tothe Point D (code addition position).

USTP


76/127

70

USER MANUAL

Setting the code to add

Confirming the modifications and return

6.11MODIFYING CODE DATA (DELETING CODE DATA)

[Example] The needle UP halt code (USTP) will be deleted from the Point D of the followingtype of stitching data.

A B C D E F

H

[Operation details] Selecting code data deletion

Determining the code deletion position

Setting the code data deletion

Press (USTP).Press .

Press and on main menu screento enter the modification mode.

Press code data change key and enterthe next setting screen.

Press jog / , and move needleto the Point D (code deletion position).

Confirm the code is Y. Press key to confirm the position.

USTP


77/127

71

USER MANUAL

Returning to the standard screen and end the modification

6.12 MODIFYING THE SECOND HOME POSITION

[Example]: The second home position in left pattern will be modified to the positon in theright pattern as shown below.

A B C D E F

H

A B C D E F

H

Caution:The second home position modification only modifies the position of the second homeposition, and never modify the position of stitching start position. The way between the second homeposition and the stitching start position is filled with moving.

[Operation details] Selecting the code data modification

Press code data deletion key .Then, on right side of screen

disappeared

Press to confirm.


Press the second home positionmodification key and enter the

setting screen.

The original secondhome positon

The modified secondhome position


78/127

72

USER MANUAL

Selecting the second home position modification

Modifying the second home positon

Confirming modification and storing

If there is no second home position inpattern, the system will display the left

screen. Then, return to the main menu screen

to select again.

Otherwise, enter the next setting screen.

Press to enter the second homeposition modification mode.

Use the direction keys to move the secondhome position to the new position.

Press .Enter the pattern creation screen.

Press to set the modification. Press to cancel modification.


79/127

73

USER MANUAL

6.13MODIFYING THE STITCHING START POSITION

[Example]: The stitching start position in left pattern will be modified to the positon inthe right pattern as shown below.

A B C D E F

H

Caution: The stitching start position modifications only modify the stitching start position, andnever modify the second home position. The way between the second home position and the stitchingstart position is filled with moving.[Operation details] Selecting the code data modification

Selecting the stitching start position modification


Press the second home positionmodification key and enter the

setting screen.

If there is no second home positon inpattern, the system will display the left

screen. Then, return to the main menu

screen to select again.

Otherwise, enter the next setting screen.

The original stitchingstart position

The modified stitchingstart position


80/127

74

USER MANUAL

Modifying the stitching start position

Confirming modification and storing

6.14 MODIFYING THE SPEED

[Example]: Select different speed to realize pattern stitching.

[Operation details] Selecting speed modification

Press to enter the stitchingstart position modification.

Use the direction keys to move the stitchstart position to the new position.

Press .Enter the pattern creation screen.

A B

C D

H

H

H

H

A B

C D

H

MD2

H

H


81/127

75

USER MANUAL

Selecting MD2 speed modification start position

Selecting MD2 speed modification start position

Selecting MD2 speed

Checking and confirming

Press and on main menu screento enter the modification mode.

Press to enter setting screen.

Press jog / , and move needle tothe Point D (modification start position).

Press to confirm.

Press jog / , and move needle tothe Point C (modification start position).

Press to confirm.

Select speed.Code MD2 means middle-high speed.

Code H is the default speed.


82/127

76

USER MANUAL

MD1 speed setting repeats the steps. L speed setting repeats the steps.6.15 BLOCK MOVEMENT(FEEDING)

[Example] The block from Point A to Point B in the following will be moved by feeding andcreated AB.

[Operation details] Selecting block movement

Setting start point A

Press to conform speed setting.

AB

Press and on the main menuscreen to enter the modification mode. Then,

press . To enter setting screen.

Press jog / , and move needle tothe Point A (start point of moving block).

Press to confirm.A

FEED

A`

A/B`

BFEED


83/127

77

USER MANUAL

Setting end point B

Selecting feeding mode, setting stitch length and moving position.


6.16 BLOCK MOVEMENT(LINEAR)

[Example] The block from Point A to Point B in the following will be moved by linear modeand created AB.

[Operation details] Selecting block movement

SEWA`

A/B`

BSEW

Press jog / , and move needle tothe Point B (end point of moving block).

Press to confirm.

Select feeding mode. Use and to set stitch length is3.0mm.

Use direction key to set moving position.

Press to confirm block movement.

B

AB


84/127

78

USER MANUAL

Setting start point A

Setting end point B

Selecting feeding mode, setting stitch length and moving position.


Press and on the main menuscreen to enter the modification mode. Then,

press . To enter setting screen.

Press jog / , and move needle tothe Point A (start point of moving block).

Press to confirm.

Press jog / , and move needleto the Point B (end point of moving

block).

Press to confirm.

A

Select feeding mode.Use and to set stitch length is3.0mm.

Use direction key to set moving position.

B


85/127

79

USER MANUAL

Press to confirm block movement


86/127

80

USER MANUAL

7 PATTERN DATA CONVERSION

Main data conversion mode functions

Function Key Details Details setting

Backtacking

Existing back tacking canbe modified, and new backtacking can be created. Start/end back tacking

FixingExisting fixing can bemodified, and new fixingcan be created.

Zigzagstitching

Existing zigzag stitchingcan be modified, and newzigzag stitching can becreated.

Multiple

The multiple distance,multiple direction andnumber of multiplestitching times formultiple stitching data canbechanged.

Entering the conversion mode

Press and on the main menu

screen to enter the conversion mode. Then, the

conversion is carried out for the current pattern

data.


87/127

81

USER MANUAL

Caution: According to the pattern data complexity, the data conversion function enters twodifferent screens as below:

1If the pattern data is complete, enter the conversion screen as below: (The pattern data based onWince is complete. )

(2) Combined pattern data or non-complete data: Non-complete pattern data includes the assistantdata losing of pattern data and the pattern data which compiled below Win 98 V3.0. The non-completepattern data can be solved by recreating.


88/127

82

USER MANUAL

7.1 BACK TACKING CONVERSION

[Example]: Convert the left pattern data into the right pattern data. Add 3 N backtackings before and after linear stitching. (The bold section is back tacking.)

H

A B C D E F G

A B

H

[Operation details] Selecting Start/end back tacking

Setting Start/end back tacking

Checking pattern data

Press to set back taking.

The details are set on this screen.The details set here are (start/end

ack tacking), start key (N mode). Press

key to set start stitch, and use

numeric key to set three start stitches.

Start key (N mode), press

key and use numeric key to set three end

stitches.

Press to confirm. Press key or key to reduce oramplify pattern.

Press to return.Press to set the conversion.


89/127

83

USER MANUAL

7.2 OVERLAP BACK TACKING CONVERSION


A B

CD

H

Caution: It is a shutting figure in the figure made in [Broken line], [Circle], [Arc], [Curve] to beable to do multiple back tacking.[Operation details] Selecting overlap back tacking conversion

Selecting conversion block

Setting the overlap back tacking details

Input a rectangle as a broken line, and

then insert overlap back tacking at the end.

(The overlap mode is entered once; three

overlap stitches are made.)

The details are set on this screen.The details set here are, (overlap

ack tacking), overlap mode , three

overlap stitches.

Press , the system will return to theinput method setting screen.

Press to set overlap back tacking.

Use / to select block, theoverlap back tacking is unavailable for feed

and liner pattern.

Press to set the multiple backtacking details.


90/127

84

USER MANUAL

Checking pattern data

Caution: Check conversion results on main menu screen. For example, one conversion will add 3overlap back tacking stitches.

Press key or key to reduce oramplify pattern.

Press to return.Press to set the conversion.


91/127

85

USER MANUAL

7.3 ZIGZAG STITCHING CONVERSION[Example] Add zigzag stitching between Point A and Point B as shown below.

A B

A B

[Operation details] Selecting zigzag conversion

Selecting conversion block

Setting the zigzag details

Press to set zigzag stitching.

Use / to select block, the zigzagis unavailable for feed and liner pattern.

Press to set the multiple backtacking details.

Press to check selected red block.


92/127

86

USER

Check

C

feeding, theIf the p

polygon. If

7.4 MU

[Examplespecifica

ANUAL

ng patter

ution: The other is linepolygon com

select 2nd se

TIPLE S

The folloion data.

data

he 5 straightear line. Sele

mpose the rection, the co

TITCHI

ing type(The mult

t lines compect 4 th sectionectangle, theonverted pat

G CON

of patterniple dista

pose the recn to convert

e user only settern is show

ERSIO

data willce is 4m

Use nto 3.0

Pr

directi

Afteset the

PressPress

ctangle. Theand create t

elects 2 sectiwn as below.

e created, the nu

umeric key

ss

n (left side)

r inputting

data.

to ret

to se

e user can sthe exampleions, one is

. Create tber of ti

to set the d

key to s

.

the details

urn.

the conve

elect 5 secte.

feeding and

e multiples is thr

flection wi

et deflect

, press

sion.

ions, one is

the other is

stitchine.)

th

ion

to

s

s


93/127

87

USER MANUAL

[Operation details] Selecting multiple stitching conversion

Selecting convers

manual book for pattern machines

Documents