milnes front cover.ai

MAY 2007

Disclaimer

All information contained in this brochure should serve as a guide only and is subject to change without notice. Gatic-Milnes Pty Ltd does not invite any person to act or rely upon such information and liability for such information is excluded. In particular, as new technology is developed rapidly, product specifications, designs and

components may change and Gatic-Milnes Pty Ltd reserves the right in its discretion to make such changes as it sees fit.

The information contained in this catalogue does not form part of the terms and conditions of sale or constitute the description of any goods to be supplied by Gatic Milnes Pty Ltd or its distributors. Before purchasing a good, customers should source current product information from their distributor and seek expert advice on their particular

intended use and application for the product.

Copyright © 2007 Gatic-Milnes Pty Ltd. No part of this catalogue may be reproduced, stored in a retrieval system of transmitted in any form, electronic, mechanical recording or otherwise without the consent of Gatic-Milnes Pty Ltd.

Milnes® is a registered trademark of Gatic-Milnes Pty. Ltd.

TABLE OF CONTENTS

May 2007 PRODUCT CATALOGUE Page 1

TABLE OF CONTENTSPage No.

2

3

4

5

6

7 - 8

9 - 11

12 - 13

14

15

16 - 19

20 - 21

22

23 - 24

25 - 26

27

28 - 30

31

31

31

31

●

●

●

General Information

Product Guide

Installation Instructions: for Tapping Saddles

Installation Instructions: for Pressure Tapping

General Technical Data: for Connection Ends

GM60A - Tapping Bands for Series 1 PVC (White) or Galvanised Steel Pipe

GM60B - Tapping Bands for Series 2 PVC (Blue), AC or DICL Pipe

GM60C - Tapping Bands for Polyethylene (PE) Pipe

GM70 - Ferrule Bends

GM70 - Self Tapping (NZ) Ferrule

GM70 - Pressure Tapping Ferulles

GM71 - Standard Ferulles

GM73 - Stop Tap Meters

GM76 - Inline Ball Valves

GM77 - Right Angle Ball Valves

GM78 - Dual Check Valve

Ball Valve Kits

Accessories

Norcast Tapping Machine

‘O’ Ring Seal Replacement

Lip Seal Replacement

Operating Pressures (All Products)

Definitions:

Allowable operating pressure - The allowable internal pressure, excluding surge that a component can safely withstand in service.Maximum allowable operating pressure - The maximum internal pressure, including surge that a component can safely withstand in service.Allowable site test pressure - Maximum pressure applied on site in a newly installed pipeline, includes a safety factor and allowances for surge.

16

Class ofProduct

(PN)

1600

Allowable operatingpressure

kPa

1920

Maximum allowableoperating pressure

kPa

2000

Allowable site testpressure

kPa

About Us

The MILNES brand name has been in the industry for more than 50 years. The range of products are for use on water supply, irrigation and plumbing pipelines.

The MILNES brand name is dedicated to customer satisfaction through product innovation and quality.

The MILNES product range comprises:

● Tapping Bands● Inline and Right Angle Ball valves● Standard and Under Pressure Tapping Ferrules ● Ferrule bends

Contact us on 1800 335 303 or your nearest MILNES distributor.

Table of Common Pipes & Diameters

-------

60

60--

6050

50

-------

75-

75--

7663

65

122122122122122122122114122114122114114

90/110

100

---

149---

140-

140--

140125/140

125

96--

969696-

89-

89--

8975

80

177177177177177177177160177160177168168160

150

---

203---

200-

200---

180

175

259259259259259259259250259250259

--

225

225

286286286286286286286280286280286273

-250/280

250

232232232232232232232225232225232219

-200

200

345345334345334345345315345315345324

-315

300

-399

-----

355-

355-

355-

355

350

-453

-----

450-

450-

406-

400

400

507507492507492507507500507500

-457

-450

450

GM60BGM60BGM60BGM60BGM60BGM60BGM60BGM60AGM60BGM60AGM60AGM60AGM60AGM60C

Tapping BandTypes

426426413426413426426400426400

----

375

DICLGRPCICL

AC

uPVC

mPVC

oPVCSTEEL

PE

DICLGRPCICLCICLACAC

uPVCuPVCmPVCmPVCoPVC

STEELGalvanised

PE

Type ofMaterial

AS/NZS2280-

AS1742.2AS/NZS2544

AS1711AS1711

AS/NZS1477AS/NZS1477

AS4765AS4765AS4441AS1579AS1074AS4130

Standard

AllAll

Class BClass C

Class A,BClass C,D

Series 2 (Blue)Series 1 (White)Series 2 (Blue)

Series 1 (White)Series 2 (Blue)

MSCLGWI

PN12.5/16

ClassNominal Size (DN)

Note: The above Chart to be used as a guide only

Tapping Bands

Ferrule Bends

Pressure Tapping Ferrules and Standard Ferrules

Inline and Right Angle Ball Valves

Description

AS4793 / MP52 SPEC025

AS3688

AS3496 / AS3718

AS4796 / MP52 SPEC012

StandardsKey Products

Key Product Specification

May 2007PRODUCT CATALOGUEPage 2

GENERAL INFORMATION

PRODUCTGUIDE


PB End SB End CB End

Tapping Band

Ferrule Bends

Pressure Tapping Ferrule

Copper Pipe

Right Angle

Stop Tap Meter WATER

METER

Right Angle Ball Valve

Ready for service

connection

Typical Applications of Milnes Pipe Fittings & Valves

NOTE:Above assembly applies to Post Installation (Under pressure tappings). Crevet® stainless steel Tapping Clamps or Taptite® tapping bands can be used for this purpose. The illustration shown are intended to serve as a guide only, individual application will depend on specific requirements. For further information contact your nearest sales office. Crevet® is a registered trademark of Crevet Ltd. Taptite® is a registered trademark of Northern Iron & Brass Foundry Pty. Ltd. (N.I.B.F.)

••

•

••

NOTE:Above assembly applies to During Installation (No pressure in pipeline). Crevet® stainless steel Clamps or D1 pretap connections can be used for this purpose. The illustration shown are intended to serve as a guide only, individual application will depend on specific requirements. For further information contact your nearest sales office.

•

•

•

Termination Box

Ready for connection to water meter

Inline Ball Valve

Poly Pipe

Tapping Band

Inline Ball Valve

Installation Instructions for Milnes Tapping Saddles

Direction for use: Prepare the area of pipe to be covered by the tapping saddle

by removing all dirt, and loose materials.

Position the bottom half of the tapping saddle making sure it is away from scored, pitted or damaged areas, as this will not provide a good seating area.

Fit the top of the tapping saddle around the pipe so that the bolts pass through the bolt holes in the top of the tapping saddle.

With one hand underneath the bottom half of the tapping saddle pressing upwards, locate the bolt holes and screw on the nuts supplied with the other hand.

Finger tighten the nuts so that the gap between the two halves of the tapping saddle is equal on both sides.

Tighten the nuts to 15ft/Ibs (20 Nm).

Additional requirements for Lip Seals:

When installing Tapping Saddles with lip seals, make sure the lip seal is in the correct position. The lips seal should be placed in the sealing groove with the sharp inner side of the lip seal facing out towards the pipe or a small moulding line running around the lip seal also indicates this should be facing down towards the pipe. If the lip seal is placed in the incorrect position the joint may leak.

Bottom TappingSaddle

Retainer ‘O’ ringhold bolts inposition.

Pipe

Ensure contact surfaceis away from scored,pitted or damage areas.

Top Tapping Saddle

Align bolts to pass through bolt holes

in the top of thetapping saddle.

Ensure seal contact areais away from scored,

pitted or damage areas.

Finger tighten the nutsso that gap betweenthe tapping saddleis equal on both sides.

Seal Installation:1. ‘O’ Ring installation.

incorrect correct

2. Lip Seal (ELS) installation.

Square inner edgeof lip seal

Sharp outer edge

incorrect correct

Tighten nuts to15ft/Ibs (20Nm)

GMOR60038GMOR60041GMOR60062

Product Code

38 X 8 NITRILE ‘O’ RING41 X 8.5 NITRILE ‘O’ RING62 X 11 NITRILE ‘O’ RING

Description

1520, 25 & 32

40 & 50

SuitsTapping Size

‘O’ Ring Seal Replacement Product Code:

GMOR60780GMOR60790

Product Code

SMALL NITRILE LIP SEALLARGE NITRILE LIP SEAL

Description

20, 25 & 3240 & 50

SuitsTapping Size

Lip Seal Replacement Product Code:


INSTALLATIONINSTRUCTIONS

Installation Instructionsfor Tapping S

addles

INSTALLATIONINSTRUCTIONS

Installation Instructions for Milnes Standard Pressure Tapping Ferrule Valves

Applications: Tapping a water main already under pressure allows services to be connected at a later date without interrupting existing consumers or water services.

For water mains, an added benefit is that keeping the water under pressure at all times prevents having to shut down the water main.

Standard Tapping Machine: Standard hand operated under pressure tapping machines allow tappings of 20 and 25mm to be made in all pipe types without the need for electrical power in remote locations or on new construction sites.

Heavy duty tapping machines suitable for tapping 32, 40 and 50mm are available. See Accessories for details.

Tapping size changes can be made by replacing screw in adaptors to the base of the tapping machine. Hard faced masonry drills are used for tapping AC, CI and DI pipes whilst a fluted hole drill is use for tapping PE and PVC to capture all the slug from the drill hole.

Direction for use: Fit an appropriate tapping band to the pipe and screw in the

selected under pressure tapping ferrule.

Unscrew the bonnet, remove the jumper valve and fully open the poly ferrule plug. (Note: A ball valve may be used in lieu of the under pressure tapping ferrule where acceptable).

Screw the tapping machine into the top of the ferrule, using the correct adaptor as required.

Rotate the feed nut until the drill tip makes contact with the pipe.

Apply pressure to the drill bit via the feed nut, turning the ratchet at the same time to cut the hole.

When drilling is completed, reverse the feed nut to retract the drill until clear of the poly ferrule plug.

Allow water escaping from the ferrule to flush the system, then close the poly ferrule plug. (A hose may be connected to the ferrule to divert the waste water).

Remove the tapping machine and replace the jumper valve and bonnet.

Connect the service pipe and open the poly ferrule plug to charge the service line.

Important Operating Instructions:

● Operate by hand only. (Added leverage will damage the machine and the drill bit).

● Minimise sideways movement during operation. (Rocking of the machine will damage the drill bit).

● Always limit the feed rate to ensure a smooth cutting action. (The feed nut may need to be restrained to prevent the drill tip from jamming).

● Do not use the upper handles to retract the feed nut. This may loosen the bearing cap which if removed under pressure will cause the following results:

(i) Dislodgement of circlip(ii) Damage to bearing(iii) Injury to operator

● Keep bearing cap screwed on tightly.

Note: The gunmetal adaptors are supplied with parallel fastening threads. Alternative threads may be supplied on request.


Installation Instructionsfor P

ressure Tapping

See Fitting Instruction forTapping Saddles for installation instructions.

RemoveBonnet

Assembly

Ensure poly ferrule plugis fully open

Ratchet

20/25mm Ferrule orBall Valve

BearingCap

Feed Nut

GunmetalAdaptor

Masonry drill suitablefor tapping A.C., C.I.,& D.I. pipes shown.Use fluted hole drill forP.E. & P.V.C. pipes.

Connectservice pipe

to chargeservice line

& open polyferrule plug

Close polyferrule plugbefore replacingtapping machinewith bonnet

Allow water escapingto flush the system

via connected pipe works.

Retract drillbit clear of

ferrule plug

General Technical D

atafor C

onnection Ends

Copper Compression Connection Details

Applications: For connection of copper pipe via the use of a compression nut to a fitting or valve.

Direction for use: Place compression nut over copper pipe to be jointed and then flare

end of copper pipe to be jointed to approximately 60 degrees using flaring tool. Ensure cut end of copper pipe is square prior to flaring.

Complete joint by tightening the compression nut over the flared copper end onto the compression end of the fitting or valve.

60°

FlaredCopper pipe

Compressionnut

Compressionend

CompletedJoint

Male Plain Threaded Connection Details

Applications: For connection to female threaded sealing pipe threads to AS1722.1.

Direction for use:Thread fitting or valve into female threaded end to achieve seal.

Femalethreaded

end

Series ‘R’ sealing pipe thread external taper pipe thread - AS1722.1: - For connection of copper pipe via the use of a compression nut to a fitting or valve.- Male threads of Ball valves- Plain thread end of Plain Ferrule bends

Series ‘RP’ sealing internal parallel thread - AS1722.1:- Female threads of Tapping Bands- Female threads of Ball Valves

Series ‘G’ fastening pipe thread internal thread - AS1722.2:- Female threads of all fastening nuts and compression nuts

Series ‘GB’ fastening pipe thread external thread Class B - AS1722.2:- Male threads of all fastening nuts and compression nuts

Thread Types for All Products

CompletedJoint

Copper Soldered Connection Details

Applications: For connection of copper pipe via the use of a soldered socket.

Direction for use: Place copper pipe to be jointed into the plain socket of fitting to be

jointed. Ensure cut end of copper pipe is square prior to jointing.

Complete joint by soldering to standard requirements.

7.57.57.57.57.5

Minimum IDLength ShortSocket (mm)

2025324050

DN(NominalDiameter)

19.0725.4231.7738.1250.82

Min. ID(mm)

19.0725.5631.9138.3251.02

Max. ID(mm)

13.517.0

---

Minimum IDLength LongSocket (mm)

Copper solderedend

Copperpipe

CompletedJoint

Applications: For connection of DN25 PE80 or PE100 Poly Pipe.

Direction for use: Place Cap nut and plastic olive over poly pipe to be jointed and insert

thimble into the pipe bore. Ensure cut end of poly pipe is square prior to jointing.

Complete joint by tightening the Cap nut over the poly connection end of the fitting or valve.

DN25 PE Poly Connection Details

g

Blue ThimbleRed Thimble

ThimbleType

PN12.5PN16

DN25PE 80

PN16/PN12.5-

DN25PE 100

Polyconnectionend

Plainolive

Blue Thimbleshown

Capnut

Polypipe

CompletedJoint

Male Plainthreaded end


GENERAL TECHNICAL DATACONNECTION ENDS

TAPPING BANDS FOR SERIES 1 PVC PIPE OR GAL. STEEL

GM60A - Tapping Bands For Series 1 (White) PVC: Pipe Size 40 - 150mm

TAP

PIN

G B

AN

DS

SE

RIE

S 1 O

R G

AL. S

TEE

LP

ipe Size 40 - 150m

m

GM60A Tapping Band SpecificationsApplications: Mechanical tapping bands provides a means for the connection of service pipes from a pipeline.GM60A Tapping Bands are suitable for the following products:

● AS/NZS1477 Series 1 White Upvc Pipe● AS/NZS4765 Series 1 White Mpvc Pipe● AS1074 Galvanised Steel Pipe

Product Standard: AS/NZS 4793 / MP52-SPEC025Pressure Rating: PN16Metallic Material: AS1565 GunmetalBolting: 316 Stainless SteelSeal: AS1646 Nitrile RubberPotable Water Compliance: AS4020


40X15 T/BAND G/METAL S1 PVC40X20 T/BAND G/METAL S1 PVC40X25 T/BAND G/METAL S1 PVC50X15 T/BAND G/METAL S1 PVC50X20 T/BAND G/METAL S1 PVC50X25 T/BAND G/METAL S1 PVC50X32 T/BAND G/METAL S1 PVC65X15 T/BAND G/METAL S1 PVC65X20 T/BAND G/METAL S1 PVC65X25 T/BAND G/METAL S1 PVC65X32 T/BAND G/METAL S1 PVC65X40 T/BAND G/METAL S1 PVC80X15 T/BAND G/METAL S1 PVC80X20 T/BAND G/METAL S1 PVC80X25 T/BAND G/METAL S1 PVC80X32 T/BAND G/METAL S1 PVC80X40 T/BAND G/METAL S1 PVC80X50 T/BAND G/METAL S1 PVC100X15 T/BAND G/METAL S1 PVC100X20 T/BAND G/METAL S1 PVC100X25 T/BAND G/METAL S1 PVC100X32 T/BAND G/METAL S1 PVC100X40 T/BAND G/METAL S1 PVC100X50 T/BAND G/METAL S1 PVC125X20 T/BAND G/METAL S1 PVC125X25 T/BAND G/METAL S1 PVC125X32 T/BAND G/METAL S1 PVC125X40 T/BAND G/METAL S1 PVC125X50 T/BAND G/METAL S1 PVC150X15 T/BAND G/METAL S1 PVC150X20 T/BAND G/METAL S1 PVC150X25 T/BAND G/METAL S1 PVC150X32 T/BAND G/METAL S1 PVC150X40 T/BAND G/METAL S1 PVC150X50 T/BAND G/METAL S1 PVC

316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING

404040505050506565656565808080808080100100100100100100125125125125125150150150150150150

NominalDiameter (mm)

‘A’

484848606060607575757575898989898989114114114114114114140140140140140160160160160160160

PipeOD** (mm)

‘B’

½"¾"1"½"¾"1"

1¼"½"¾"1"

1¼"1½"½"¾"1"

1¼"1½"2"½"¾"1"

1¼"1½"2"¾"1"

1¼"1½"2"½"¾"1"

1¼"1½"2"

Tapping SizeBSP (in)

‘C’

1520251520253215202532401520253240501520253240502025324050152025324050

TappingSizeBSP (mm)

‘C’

GM60A4015GM60A4020GM60A4025GM60A5015GM60A5020GM60A5025GM60A5032GM60A6515GM60A6520GM60A6525GM60A6532GM60A6540GM60A8015GM60A8020GM60A8025GM60A8032GM60A8040GM60A8050GM60A10015GM60A10020GM60A10025GM60A10032GM60A10040GM60A10050GM60A12520GM60A12525GM60A12532GM60A12540GM60A12550GM60A15015GM60A15020GM60A15025GM60A15032GM60A15040GM60A15050

Productcode

DescriptionTypical dimensions

‘A’

‘C’*

‘B’

Seal Option:1. ‘O’ Ring seal

316 SSBolting

- White PVC Pipe Series 1

- GalvanisedSteel Pipe

GM60A4015Tapping Size - BSP 15mm

Nominal Diameter - Ø40mm

Product Type - Tapping Band Series 1

Product Code Specification:

NOTE:For installation detail, refer to Installation Instructions.Refer to thread standard Series 'RP' Sealing Internal Parallel Thread. Refer to AS1722.1 for further details.Refer to pipe product standard for actual pipe tolerance. e.g. AS4765 for Mpvc pipe tolerances.The illustration shown is intended to serve as a guide only. Detailed drawings and specification can be obtained by contacting the nearest sales office.

•*

**•

GM60A Tapping Band SpecificationsApplications: Mechanical tapping bands provides a means for the connection of service pipes from a pipeline.GM60A Tapping Bands are suitable for the following products:

● AS/NZS1477 Series 1 White Upvc Pipe● AS/NZS4765 Series 1 White Mpvc Pipe● AS1074 Galvanised Steel Pipe


175X20 T/BAND G/METAL S1 PVC175X25 T/BAND G/METAL S1 PVC175X32 T/BAND G/METAL S1 PVC175X40 T/BAND G/METAL S1 PVC175X50 T/BAND G/METAL S1 PVC200X15 T/BAND G/METAL S1 PVC200X20 T/BAND G/METAL S1 PVC200X25 T/BAND G/METAL S1 PVC200X32 T/BAND G/METAL S1 PVC200X40 T/BAND G/METAL S1 PVC200X50 T/BAND G/METAL S1 PVC225X15 T/BAND G/METAL S1 PVC225X20 T/BAND G/METAL S1 PVC225X25 T/BAND G/METAL S1 PVC225X32 T/BAND G/METAL S1 PVC225X40 T/BAND G/METAL S1 PVC225X50 T/BAND G/METAL S1 PVC250X15 T/BAND G/METAL S1 PVC250X20 T/BAND G/METAL S1 PVC250X25 T/BAND G/METAL S1 PVC250X32 T/BAND G/METAL S1 PVC250X40 T/BAND G/METAL S1 PVC250X50 T/BAND G/METAL S1 PVC300X15 T/BAND G/METAL S1 PVC300X20 T/BAND G/METAL S1 PVC300X25 T/BAND G/METAL S1 PVC300X32 T/BAND G/METAL S1 PVC300X40 T/BAND G/METAL S1 PVC300X50 T/BAND G/METAL S1 PVC375X15 T/BAND G/METAL S1 PVC375X20 T/BAND G/METAL S1 PVC375X25 T/BAND G/METAL S1 PVC375X32 T/BAND G/METAL S1 PVC375X40 T/BAND G/METAL S1 PVC375X50 T/BAND G/METAL S1 PVC

316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING

175175175175175200200200200200200225225225225225225250250250250250250300300300300300300375375375375375375


‘A’

200200200200200225225225225225225250250250250250250280280280280280280315315315315315315400400400400400400

PipeOD** (mm)

‘B’

¾"1"

1¼"1½"2"½"¾"1"

1¼"1½"2"½"¾"1"

1¼"1½"2"½"¾"1"

1¼"1½"2"½"¾"1"

1¼"1½"2"½"¾"1"

1¼"1½"2"


‘C’

2025324050152025324050152025324050152025324050152025324050152025324050

TappingSizeBSP (mm)

‘C’

GM60A17520GM60A17525GM60A17532GM60A17540GM60A17550GM60A20015GM60A20020GM60A20025GM60A20032GM60A20040GM60A20050GM60A22515GM60A22520GM60A22525GM60A22532GM60A22540GM60A22550GM60A25015GM60A25020GM60A25025GM60A25032GM60A25040GM60A25050GM60A30015GM60A30020GM60A30025GM60A30032GM60A30040GM60A30050GM60A37515GM60A37520GM60A37525GM60A37532GM60A37540GM60A37550

Productcode


- White PVC Pipe Series 1

- GalvanisedSteel Pipe

GM60A - Tapping Bands For Series 1 (White) PVC: Pipe Size 175 - 375mm

‘A’

‘C’*

‘B’

316 SSBolting

GM60A17520Tapping Size - BSP 20mm





•*

**•

Seal Option:1. ‘O’ Ring seal


TAP

PIN

G B

AN

DS

SE

RIE

S 1 O

R G

AL. S

TEE

LP

ipe Size 175 - 375m

m

TAPPING BANDS FOR SERIES 1 PVC PIPE OR GAL. STEEL

TAPPING BANDS FOR SERIES 2(BLUE) PVC, AC OR DICL PIPE

GM60B - Tapping Bands For Series 2 (Blue) PVC, AC or DICL: Pipe Size 50 - 100mm

TAP

PIN

G B

AN

DS

SE

RIE

S 2

Pipe S

ize 50 - 100mm


50X15 T/BAND G/METAL AC/S250X20 T/BAND G/METAL AC/S250X25 T/BAND G/METAL AC/S258X20 T/BAND G/METAL AC/S258X20 T/BAND G/METAL AC/S258X25 T/BAND G/METAL AC/S258X40 T/BAND G/METAL AC/S258X50 T/BAND G/METAL AC/S280X15 T/BAND G/METAL AC/S280X20 T/BAND G/METAL AC/S280X20 T/BAND G/METAL AC/S280X25 T/BAND G/METAL AC/S280X25 T/BAND G/METAL AC/S280X32 T/BAND G/METAL AC/S280X32 T/BAND G/METAL AC/S280X40 T/BAND G/METAL AC/S280X40 T/BAND G/METAL AC/S280X50 T/BAND G/METAL AC/S280X50 T/BAND G/METAL AC/S2100X15 T/BAND G/METAL AC/S2100X20 T/BAND G/METAL AC/S2100X20 T/BAND G/METAL AC/S2100X25 T/BAND G/METAL AC/S2100X25 T/BAND G/METAL AC/S2100X32 T/BAND G/METAL AC/S2100X32 T/BAND G/METAL AC/S2100X40 T/BAND G/METAL AC/S2100X40 T/BAND G/METAL AC/S2100X50 T/BAND G/METAL AC/S2100X50 T/BAND G/METAL AC/S2

316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING

50505058585858588080808080808080808080100100100100100100100100100100100


‘A’

70707078787878789696969696969696969696122122122122122122122122122122122

PipeOD** (mm)

‘B’

½"¾"1"¾¾1"

1½"2"½"¾"¾"1"1"

1¼"1¼"1½"1½"2"2"½"¾"¾"1"1"

1¼"1¼"1½"1½"2"2"


‘C’

152025202025405015202025253232404050501520202525323240405050

TappingSizeBSP (mm)

‘C’

GM60B5015GM60B5020GM60B5025GM60B5820GM60B5820ELSGM60B5825GM60B5840GM60B5850ELSGM60B8015GM60B8020GM60B8020ELSGM60B8025GM60B8025ELSGM60B8032GM60B8032ELSGM60B8040GM60B8040ELSGM60B8050GM60B8050ELSGM60B10015GM60B10020GM60B10020ELSGM60B10025GM60B10025ELSGM60B10032GM60B10032ELSGM60B10040GM60B10040ELSGM60B10050GM60B10050ELS

Productcode


GM60B Tapping Band SpecificationsApplications: Mechanical tapping bands provides a means for the connection of service pipes from a pipeline.GM60B Tapping Bands are suitable for the following products:

● AS/NZS1477 Series 2 Blue Upvc Pipe● AS/NZS4765 Series 2 Blue Mpvc Pipe● AS/NZS4441 Series 2 Blue Opvc Pipe● AS/NZS2280 DI Pipe (Insulation may be required for Bi-Metallic contact)● AS4139 Asbestos Cement Pipe


GM60B5820ELS

Tapping Size - BSP 20mm

Seal Option - Lip Ring Seal





•*

**•

‘A’

‘C’*

‘B’

316 SSBolting

(Blue) PVC PipeSeries 2,AC or DICL

Seal Options:1. ‘O’ Ring:

2. Lip Seal (ELS):


150X15 T/BAND G/METAL AC/S2150X20 T/BAND G/METAL AC/S2150X20 T/BAND G/METAL AC/S2150X25 T/BAND G/METAL AC/S2150X25 T/BAND G/METAL AC/S2150X32 T/BAND G/METAL AC/S2150X32 T/BAND G/METAL AC/S2150X40 T/BAND G/METAL AC/S2150X40 T/BAND G/METAL AC/S2150X50 T/BAND G/METAL AC/S2150X50 T/BAND G/METAL AC/S2200X15 T/BAND G/METAL AC/S2200X20 T/BAND G/METAL AC/S2200X20 T/BAND G/METAL AC/S2200X25 T/BAND G/METAL AC/S2200X25 T/BAND G/METAL AC/S2200X32 T/BAND G/METAL AC/S2200X32 T/BAND G/METAL AC/S2200X40 T/BAND G/METAL AC/S2200X40 T/BAND G/METAL AC/S2200X50 T/BAND G/METAL AC/S2200X50 T/BAND G/METAL AC/S2225X15 T/BAND G/METAL AC/S2225X20 T/BAND G/METAL AC/S2225X25 T/BAND G/METAL AC/S2225X25 T/BAND G/METAL AC/S2225X32 T/BAND G/METAL AC/S2225X40 T/BAND G/METAL AC/S2225X40 T/BAND G/METAL AC/S2225X50 T/BAND G/METAL AC/S2

316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTING

150150150150150150150150150150150200200200200200200200200200200200225225225225225225225225

NominalDia. (mm)

‘A’

177177177177177177177177177177177232232232232232232232232232232232259259259259259259259259

PipeOD** (mm)

‘B’

½"¾"¾"1"1"

1¼"1¼"1½"1½"2"2"½"¾"¾"1"1"

1¼"1¼"1½"1½"2"2"½"¾"1"1"

1¼"1½"1½"2"


‘C’

152020252532324040505015202025253232404050501520252532404050

TappingSizeBSP (mm)

‘C’

GM60B15015GM60B15020GM60B15020ELSGM60B15025GM60B15025ELSGM60B15032GM60B15032ELSGM60B15040GM60B15040ELSGM60B15050GM60B15050ELSGM60B20015GM60B20020GM60B20020ELSGM60B20025GM60B20025ELSGM60B20032GM60B20032ELSGM60B20040GM60B20040ELSGM60B20050GM60B20050ELSGM60B22515GM60B22520GM60B22525GM60B22525ELSGM60B22532GM60B22540GM60B22540ELSGM60B22550

Productcode



TAP

PIN

G B

AN

DS

SE

RIE

S 2

Pipe S

ize 150 - 225mm

‘A’

‘C’*

‘B’

316 SSBolting





GM60B15020ELS







•*

**•



2. Lip Seal (ELS):

250X15 T/BAND G/METAL AC/S2250X20 T/BAND G/METAL AC/S2250X20 T/BAND G/METAL AC/S2250X25 T/BAND G/METAL AC/S2250X25 T/BAND G/METAL AC/S2250X32 T/BAND G/METAL AC/S2250X40 T/BAND G/METAL AC/S2250X40 T/BAND G/METAL AC/S2250X50 T/BAND G/METAL AC/S2250X50 T/BAND G/METAL AC/S2300X15 T/BAND G/METAL AC/S2300X20 T/BAND G/METAL AC/S2300X20 T/BAND G/METAL AC/S2300X25 T/BAND G/METAL AC/S2300X25 T/BAND G/METAL AC/S2300X32 T/BAND G/METAL AC/S2300X40 T/BAND G/METAL AC/S2300X40 T/BAND G/METAL AC/S2300X50 T/BAND G/METAL AC/S2300X50 T/BAND G/METAL AC/S2375X15 T/BAND G/METAL AC/S2375X20 T/BAND G/METAL AC/S2375X20 T/BAND G/METAL AC/S2375X25 T/BAND G/METAL AC/S2375X25 T/BAND G/METAL AC/S2375X32 T/BAND G/METAL AC/S2375X40 T/BAND G/METAL AC/S2375X40 T/BAND G/METAL AC/S2375X50 T/BAND G/METAL AC/S2375X50 T/BAND G/METAL AC/S2450X15 T/BAND G/METAL AC/S2450X20 T/BAND G/METAL AC/S2450X25 T/BAND G/METAL AC/S2450X25 T/BAND G/METAL AC/S2450X32 T/BAND G/METAL AC/S2450X40 T/BAND G/METAL AC/S2450X50 T/BAND G/METAL AC/S2

316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING

250250250250250250250250250250300300300300300300300300300300375375375375375375375375375375450450450450450450450

NominalDia. (mm)

‘A’

286286286286286286286286286286345345345345345345345345345345426426426426426426426426426426507507507507507507507

PipeOD** (mm)

‘B’

½"¾"¾"1"1"

1¼"1½"1½"2"2"½"¾"¾"1"1"

1¼"1½"1½"2"2"½"¾"¾"1"1"

1¼"1½"1½"2"2"½"¾"1"1"

1¼"1½"2"


‘C’

15202025253240405050152020252532404050501520202525324040505015202525324050

TappingSizeBSP (mm)

‘C’

GM60B25015GM60B25020GM60B25020ELSGM60B25025GM60B25025ELSGM60B25032GM60B25040GM60B25040ELSGM60B25050GM60B25050ELSGM60B30015GM60B30020GM60B30020ELSGM60B30025GM60B30025ELSGM60B30032GM60B30040GM60B30040ELSGM60B30050GM60B30050ELSGM60B37515GM60B37520GM60B37520ELSGM60B37525GM60B37525ELSGM60B37532GM60B37540GM60B37540ELSGM60B37550GM60B37550ELSGM60B45015GM60B45020GM60B45025GM60B45025ELSGM60B45032GM60B45040GM60B45050

Productcode




TAP

PIN

G B

AN

DS

SE

RIE

S 2

Pipe S

ize 250 - 450mm


‘A’

‘C’*

‘B’

316 SSBolting





GM60B25020ELS







•*

**•


2. Lip Seal (ELS):


TAPPING BANDS FORPOLYETHYLENE PIPE (PE)

GM60C - Tapping Bands For Polyethylene Pipe (PE): Pipe Size 63 - 160mm

TAP

PIN

G B

AN

DS

PE

Pipe S

ize 63 - 160mm

GM60C Tapping Band SpecificationsApplications: Mechanical tapping bands provides a means for the connection of service pipes from a pipeline.GM60C Tapping Bands are suitable for the following products:

● AS/NZS4130 MDPE, HDPEProduct Standard: MP52-SPEC025Pressure Rating: PN16Metallic Material: AS1565 GunmetalBolting: 316 Stainless SteelSeal: AS1646 Nitrile RubberPotable Water Compliance: AS4020 ‘A’

‘C’*

‘B’

316 SSBolting

PE Pipe

GM60C6320ELS




Product Type - Tapping Band PE



•*

**•


2. Lip Seal (ELS):

63637575757575909090909090125125125160160160160160160


‘A’

63637575757575909090909090125125125160160160160160160

PipeOD** (mm)

‘B’

¾"1"½"¾"1"

1¼"1½"½"¾"1"

1¼"1½"2"¾"1"

1¼"½"¾"1"

1¼"1½"2"


‘C’

20251520253240152025324050202532152025324050

TappingSizeBSP (mm)

‘C’

GM60C6320GM60C6325GM60C7515GM60C7520GM60C7525GM60C7532GM60C7540GM60C9015GM60C9020GM60C9025GM60C9032GM60C9040GM60C9050GM60C12520GM60C12525GM60C12532GM60C16015GM60C16020GM60C16025GM60C16032GM60C16040GM60C16050

Productcode

--

GM60A6515GM60A6520GM60A6525GM60A6532GM60A6540GM60A8015GM60A8020GM60A8025GM60A8032GM60A8040GM60A8050

---

GM60A15015GM60A15020GM60A15025GM60A15032GM60A15040GM60A15050

AlternativeProduct

Code

63X20 T/BAND G/METAL MDPE63X25 T/BAND G/METAL MDPE75X15 T/BAND G/METAL MDPE75X20 T/BAND G/METAL MDPE75X25 T/BAND G/METAL MDPE75X32 T/BAND G/METAL MDPE75X40 T/BAND G/METAL MDPE90X15 T/BAND G/METAL MDPE90X20 T/BAND G/METAL MDPE90X25 T/BAND G/METAL MDPE90X32 T/BAND G/METAL MDPE90X40 T/BAND G/METAL MDPE90X50 T/BAND G/METAL MDPE125X20 T/BAND G/METAL MDPE125X25 T/BAND G/METAL MDPE125X32 T/BAND G/METAL MDPE160X15 T/BAND G/METAL MDPE160X20 T/BAND G/METAL MDPE160X25 T/BAND G/METAL MDPE160X32 T/BAND G/METAL MDPE160X40 T/BAND G/METAL MDPE160X50 T/BAND G/METAL MDPE

316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING


180180180180180180180200225225225250250250250250280280280280315315315315


‘A’

180180180180180180180200225225225250250250250250280280280280315315315315

PipeOD (mm)

‘B’

¾"¾"1"1"

1¼"1½"2"2"¾"1½"2"¾"1"

1¼"1½"2"¾"1¼"1½"2"¾"1"

1½"2"


‘C’

202025253240505020405020253240502032405020254050

TappingSizeBSP (mm)

‘C’

GM60C18020GM60C18020ELSGM60C18025GM60C18025ELSGM60C18032GM60C18040GM60C18050GM60C20050GM60C22520GM60C22540GM60C22550GM60C25020GM60C25025GM60C25032GM60C25040GM60C25050GM60C28020GM60C28032GM60C28040GM60C28050GM60C31520GM60C31525GM60C31540GM60C31550

Productcode

180X20 T/BAND G/METAL MDPE180X20 T/BAND G/METAL MDPE180X25 T/BAND G/METAL MDPE180X25 T/BAND G/METAL MDPE180X32 T/BAND G/METAL MDPE180X40 T/BAND G/METAL MDPE180X50 T/BAND G/METAL MDPE200X50 T/BAND G/METAL MDPE225X20 T/BAND G/METAL MDPE225X40 T/BAND G/METAL MDPE225X50 T/BAND G/METAL MDPE250X20 T/BAND G/METAL MDPE250X25 T/BAND G/METAL MDPE250X32 T/BAND G/METAL MDPE250X40 T/BAND G/METAL MDPE250X50 T/BAND G/METAL MDPE280X20 T/BAND G/METAL MDPE280X32 T/BAND G/METAL MDPE280X40 T/BAND G/METAL MDPE280X50 T/BAND G/METAL MDPE315X20 T/BAND G/METAL MDPE315X25 T/BAND G/METAL MDPE315X40 T/BAND G/METAL MDPE315X50 T/BAND G/METAL MDPE

316 SS BOLTINGELS & 316 SS BOLTINGELS & 316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING316 SS BOLTING


GM60C18020ELS




Product Type - Tapping Band PE


TAPPING BANDS FORPOLYETHYLENE PIPE (PE)

GM60C - Tapping Bands For Polyethylene Pipe (PE): Pipe Size 180 - 315mm

TAP

PIN

G B

AN

DS

PE

Pipe S

ize 180 - 315mm

GM60C Tapping Band SpecificationsApplications: Mechanical tapping bands provides a means for the connection of service pipes from a pipeline.GM60C Tapping Bands are suitable for the following products:

● AS/NZS4130 MDPE, HDPEProduct Standard: MP52-SPEC025Pressure Rating: PN16Metallic Material: AS1565 GunmetalBolting: 316 Stainless SteelSeal: AS1646 Nitrile RubberPotable Water Compliance: AS4020


‘A’

‘C’*

‘B’

316 SSBolting

PE Pipe


•*

**•


2. Lip Seal (ELS):

-------

GM60A17550GM60A20020GM60A20040GM60A20050GM60A22520GM60A22525GM60A22532GM60A22540GM60A22550GM60A25020GM60A25032GM60A25040GM60A25050GM60A30020GM60A30025GM60A30040GM60A30050

AlternativeProduct

Code

GM70 - Ferrule Bends

GM70 Ferrule Bend SpecificationsOutlets:

● Compression end suitable for copper pipe to AS1432● Soldered end suitable for Copper pipe to AS1432● Plain end suitable for connection via Series 'R'

sealing pipe thread external taper pipe thread - AS1722.1

Product Standard: AS3688Pressure Rating: PN16Metallic Material: Bend AS1565 Gunmetal/Compression nut AS1567/8 BrassPotable Water Compliance: AS4020

GM7020CBOption CB - Compression End

SB - Soldered EndPB - Male Plain End


Product Type - Ferrule Series


20 FERRULE BEND COMP - COMPRESSION END25 FERRULE BEND COMP - COMPRESSION END32 FERRULE BEND COMP - COMPRESSION END40 FERRULE BEND COMP - COMPRESSION END50 FERRULE BEND COMP - COMPRESSION END20 FERRULE BEND SOLDERED - SOLDERED END25 FERRULE BEND SOLDERED - SOLDERED END32 FERRULE BEND SOLDERED - SOLDERED END40 FERRULE BEND SOLDERED - SOLDERED END50 FERRULE BEND SOLDERED - SOLDERED END20 FERRULE BEND MI - MALE IRON/PLAIN MALE END25 FERRULE BEND MI - MALE IRON/PLAIN MALE END32 FERRULE BEND MI - MALE IRON/PLAIN MALE END40 FERRULE BEND MI - MALE IRON/PLAIN MALE END50 FERRULE BEND MI - MALE IRON/PLAIN MALE END

202532405020253240502025324050

Nominal Diameter (mm)‘A’

GM7020CBGM7025CBGM7032CBGM7040CBGM7050CBGM7020SBGM7025SBGM7032SBGM7040SBGM7050SBGM7020PBGM7025PBGM7032PBGM7040PBGM7050PB

Productcode

DescriptionTypical dimension

‘A’

CompressionEnd*

Male Iron (MI)/Plain

(threaded) End**

COMPRESSION BEND

PLAIN BEND

SolderedEnd^

SOLDERED BEND

‘A’‘A’

NOTE:Refer to Internal Diameter of Soldered Ends of Ferrule Bends Table in this catalogue for further details.Refer to thread standard Series 'G' Fastening Pipe Thread Internal Thread & Series 'GB' Fastening Pipe Thread External Thread Class B. Refer to AS1722.1 for further details.Refer to thread standard Series 'R' Sealing Pipe Thread External Taper Pipe Thread. Refer to AS1722.1 for further details.The illustration shown is intended to serve as a guide only. Detailed drawings and specification can be obtained by contacting the nearest sales office.

^*

**•


FER

RU

LE S

ER

IES

:FE

RR

ULE

BE

ND

S

FERRULE SERIES:FERRULE BENDS

FERRULE SERIES:SELF TAPPING (NZ) FERRULE

GM70 - Self Tapping (NZ) Ferrule

GM70 Self Tapping (NZ) Ferrule Specifications

Pressure Rating: PN16Metallic Material: Bend AS1565 GunmetalPotable Water Compliance: AS4020


GM7020NZOption NZ - Self Tapping




20 FERRULE BEND NZ SELF TAPPING 20


GM7020NZ

Productcode


NOTE:The illustration shown is intended to serve as a guide only. Detailed drawings and specification can be obtained by contacting the nearest sales office.•

‘A’

FER

RU

LE S

ER

IES

:S

ELF TA

PP

ING

(NZ) FE

RR

ULE

GM70 - Bonnet Assembly

20 PRESSURE TAPPING FERRULES25 PRESSURE TAPPING FERRULES32 PRESSURE TAPPING FERRULES40 PRESSURE TAPPING FERRULES50 PRESSURE TAPPING FERRULES

BONNET ASSEMBLYBONNET ASSEMBLYBONNET ASSEMBLYBONNET ASSEMBLYBONNET ASSEMBLY

2025324050


GM7020BAGM7025BAGM7032BAGM7040BAGM7050BA

Productcode


NOTE:For installation detail, refer to Installation Instruction.The illustration shown is intended to serve as a guide only. Detailed drawings and specification can be obtained by contacting the nearest sales office.

••

GM70 Pressure Tapping Ferrules Specification

Product Standard: AS/NZS3718 / AS3496Pressure Rating: PN16Potable Water Compliance: AS4020

GM7020BAOption - Bonnet Assembly




Spindle head.(Optional Tee-headavailable)

Thread to suitnominal ferrule bodies

Jumper Valve

GM70 - Cap Assembly

40 PRESSURE TAPPING FERRULES CAP ASSEMBLY 40


GM7040CAP

Productcode


GM70 Pressure Tapping Ferrules Specification


GM7020CAPOption - Cap Assembly



Product Code Specification:Thread to suitnominal ferrule bodies

FER

RU

LE S

ER

IES

:P

RE

SS

UR

E TA

PP

ING

FER

RU

LES


FERRULE SERIES: PRESSURE TAPPING FERRULES

GM70 Pressure Tapping Ferrules Specification Product Standard: AS/NZS3718 / AS3496Pressure Rating: PN16Potable Water Compliance: AS4020

GM70 - Pressure Tapping Ferrule: with Bonnet Assembly


WITH BONNET ASSEMBLYWITH BONNET ASSEMBLYWITH BONNET ASSEMBLYWITH BONNET ASSEMBLYWITH BONNET ASSEMBLY

2025324050


GM7020BGM7025BGM7032BGM7040BGM7050B

Productcode


GM7020BOption B - Pressure Tapping

Ferrule with Bonnet




Outlet to suitFerrule bends

FER

RU

LE S

ER

IES

:P

RE

SS

UR

E TA

PP

ING

FER

RU

LES

‘A’



Tapered Thread Inlet*

BonnetAssembly

NOTE:For installation detail, refer to Installation Instructions.Refer to thread standard Series 'R' Sealing Pipe Thread External Taper Pipe Thread. Refer to AS1722.1 for further details.The illustration shown is intended to serve as a guide only. Detailed drawings and specification can be obtained by contacting the nearest sales office.

•*•


GM70 - Pressure Tapping Ferrule: with Cap Assembly


WITH CAP ASSEMBLYWITH CAP ASSEMBLYWITH CAP ASSEMBLYWITH CAP ASSEMBLYWITH CAP ASSEMBLY

2025324050


GM7020CGM7025CGM7032CGM7040CGM7050C

Productcode


GM7020COption C - Pressure Tapping

Ferrule with Cap




Outlet to suitFerrule bends

‘A’


Cap Assembly


GM70 - Pressure Tapping Ferrule: with Poly Outlet & Bonnet Assembly

20 PRESSURE TAPPING FERRULES25 PRESSURE TAPPING FERRULES

POLY OULTET WITH BONNET ASSYPOLY OUTLET WITH BONNET ASSY

2025


GM7020BPGM7025BP

Productcode


GM7020BPOption BP - Pressure Tapping

Ferrule with Poly Outlet & Bonnet




‘A’

PolyOutlet


BonnetAssembly

NOTE:For installation detail, refer to Installation Instructions.Refer to thread standard Series 'R' Sealing Pipe Thread External Taper Pipe Thread. Refer to AS1722.1 for further details.The illustration shown is intended to serve as a guide only. Detailed drawings and specification can be obtained by contacting the nearest sales office.

•*•

PolyOutlet


Cap Assembly


GM70 - Pressure Tapping Ferrule: with Poly Outlet & Cap Assembly

20 PRESSURE TAPPING FERRULES25 PRESSURE TAPPING FERRULES

POLY OUTLET WITH CAP ASSYPOLY OUTLET WITH CAP ASSY

2025


GM7020CPGM7025CP

Productcode


GM7020CPOption CP - Pressure Tapping

Ferrule with Poly Outlet & Cap




‘A’

FER

RU

LE S

ER

IES

:P

RE

SS

UR

E TA

PP

ING

FER

RU

LES



FER

RU

LE S

ER

IES

:P

RE

SS

UR

E TA

PP

ING

FER

RU

LES

GM7020CPBOption CPB - Pressure Tapping Ferrule

with Male Plain & Cap






GM70 - Pressure Tapping Ferrule: with Ferrule Bends Outlet & Bonnet Assembly

GM70 - Pressure Tapping Ferrule: with Ferrule Bends Outlet & Cap Assembly

NOTE:For installation detail, refer to Installation Instruction.Refer to thread standard Series 'R' Sealing Pipe Thread External Taper Pipe Thread. Refer to AS1722.1 for further details.The illustration shown is intended to serve as a guide only. Detailed drawings and specification can be obtained by contacting the nearest sales office.

•*•


20 PRESSURE TAPPING FERRULES25 PRESSURE TAPPING FERRULES32 PRESSURE TAPPING FERRULES40 PRESSURE TAPPING FERRULES50 PRESSURE TAPPING FERRULES20 PRESSURE TAPPING FERRULES25 PRESSURE TAPPING FERRULES32 PRESSURE TAPPING FERRULES40 PRESSURE TAPPING FERRULES50 PRESSURE TAPPING FERRULES20 PRESSURE TAPPING FERRULES25 PRESSURE TAPPING FERRULES32 PRESSURE TAPPING FERRULES40 PRESSURE TAPPING FERRULES50 PRESSURE TAPPING FERRULES

CW 20MM FERRULE BEND CU COMPCW 25MM FERRULE BEND CU COMPCW 32MM FERRULE BEND CU COMPCW 40MM FERRULE BEND CU COMPCW 50MM FERRULE BEND CU COMPCW 20MM FERRULE BEND SOLDEREDCW 32MM FERRULE BEND SOLDEREDCW 25MM FERRULE BEND SOLDEREDCW 40MM FERRULE BEND SOLDEREDCW 50MM FERRULE BEND SOLDEREDCW 20MM FERRULE BEND MICW 25MM FERRULE BEND MICW 32MM FERRULE BEND MICW 40MM FERRULE BEND MICW 50MM FERRULE BEND MI

GM7020BCBGM7025BCBGM7032BCBGM7040BCBGM7050BCBGM7020BSBGM7025BSBGM7032BSBGM7040BSBGM7050BSBGM7020BPBGM7025BPBGM7032BPBGM7040BPBGM7050BPB

Productcode

Description

202532405020253240502025324050


Typical dimension

25 PRESSURE TAPPING FERRULES40 PRESSURE TAPPING FERRULES50 PRESSURE TAPPING FERRULES

CW 25MM FERRULE BEND MICW 40MM FERRULE BEND MICW 50MM FERRULE BEND MI

GM7025CPBGM7040CPBGM7050CPB

Productcode

Description

254050


Typical dimension

GM7020BCBOption BCB - Pressure Tapping Ferrule

with Copper CompressionOutlet & Bonnet

BSB - Pressure Tapping Ferrule with Copper SolderedOutlet & Bonnet

BPB - Pressure Tapping Ferrule with Plain MaleOutlet & Bonnet





‘A’

PB EndSB EndCB End

BonnetAssembly

CapAssembly

‘A’

PB End**


GM71 - Bonnet Assembly

20 TEE HEAD BONNET ASSEMBLY25 TEE HEAD BONNET ASSEMBLY

2025


GM71B20GM71B25

Productcode


GM71 Standard Ferrule Specification


GM71 Standard Ferrule Specification Product Standard: AS/NZS3718 / AS3496Pressure Rating: PN16Potable Water Compliance: AS4020

GM71B20Nominal Diameter - Ø20mm

Option B - Tee HeadBonnet Assembly

Product Type - Standard Ferrule Series


Thread to suitnominal ferrule bodies

GM71 - Standard Ferrule

20 STANDARD FERRULES25 STANDARD FERRULES32 STANDARD FERRULES40 STANDARD FERRULES50 STANDARD FERRULES

2025324050


GM7120GM7125GM7132GM7140GM7150

Productcode


GM7120Nominal Diameter - Ø20mm



Jumper Valve

NOTE:Refer to thread standard Series 'R' Sealing Pipe Thread External Taper Pipe Thread. Refer to AS1722.1 for further details.The illustration shown is intended to serve as a guide only. Detailed drawings and specification can be obtained by contacting the nearest sales office.*•

Tee HeadFER

RU

LE S

ER

IES

:S

TAN

DA

RD

FER

RU

LES


FERRULE SERIES: STANDARD FERRULES

FERRULE SERIES: STANDARD FERRULES

GM71 - Standard Ferrule: with Ferrule Bends Outlet & Bonnet Assembly

GM70 Standard Ferrules Specification Product Standard: AS/NZS3718 / AS3496Pressure Rating: PN16Potable Water Compliance: AS4020

20 STANDARD FERRULES25 STANDARD FERRULES32 STANDARD FERRULES40 STANDARD FERRULES50 STANDARD FERRULES20 STANDARD FERRULES25 STANDARD FERRULES32 STANDARD FERRULES40 STANDARD FERRULES50 STANDARD FERRULES20 STANDARD FERRULES25 STANDARD FERRULES32 STANDARD FERRULES40 STANDARD FERRULES50 STANDARD FERRULES

CW 20MM FERRULE BEND CU COMPCW 25MM FERRULE BEND CU COMPCW 32MM FERRULE BEND CU COMPCW 40MM FERRULE BEND CU COMPCW 50MM FERRULE BEND CU COMPCW 20MM FERRULE BEND SOLDEREDCW 25MM FERRULE BEND SOLDEREDCW 32MM FERRULE BEND SOLDEREDCW 40MM FERRULE BEND SOLDEREDCW 50MM FERRULE BEND SOLDEREDCW 20MM FERRULE BEND MICW 25MM FERRULE BEND MICW 32MM FERRULE BEND MICW 40MM FERRULE BEND MICW 50MM FERRULE BEND MI

GM7120BCBGM7125BCBGM7132BCBGM7140BCBGM7150BCBGM7120BSBGM7125BSBGM7132BSBGM7140BSBGM7150BSBGM7120BPBGM7125BPBGM7132BPBGM7140BPBGM7150BPB

Productcode

Description

202532405020253240502025324050


Typical dimension

GM7120BCBOption BCB - Pressure Tapping

Ferrule with Copper CompressionOutlet & Bonnet

BSB - Pressure Tapping Ferrule with Copper Soldered Outlet & Bonnet

BPB - Pressure Tapping Ferrule with Plain Male Outlet & Bonnet





‘A’

PB End**SB End^CB End*Bonnet

Assembly



FER

RU

LE S

ER

IES

:S

TAN

DA

RD

FER

RU

LES

GM73 - Right Angle Stop Tap Meter: Female Outlet (CC - FI)

20 STOP TAP METER CC X FI25 STOP TAP METER CC X FI

2025


GM73A20GM73A25

Productcode


GM73 Right Angle Stop Tap Meter Specification


GM73 Right Angle Stop Tap Meter Specification Product Standard: AS/NZS3718 / AS3496Pressure Rating: PN16Potable Water Compliance: AS4020

GM73A20Nominal Diameter - Ø20mm

Product Type - Female Outlet

Product Type - Stop Tap Meter


GM73 - Right Angle Stop Tap Meter: Male Outlet (CC - MI)

20 STOP TAP METER CC X MI25 STOP TAP METER CC X MI

2025


GM7320GM7325

Productcode



Product Type - Stop Tap Meter


‘A’

‘A’

Bonnet Assembly

Bonnet Assembly

NOTE:Refer to thread standard Series 'G' Fastening Pipe Thread Internal Thread & Series 'GB' Fastening Pipe Thread External Thread Class B. Refer to AS1722.1 for further details.The illustration shown is intended to serve as a guide only. Detailed drawings and specification can be obtained by contacting the nearest sales office.*•

NOTE:Refer to thread standard Series 'G' Fastening Pipe Thread Internal Thread & Series 'GB' Fastening Pipe Thread External Thread Class B. Refer to AS1722.1 for further details.The illustration shown is intended to serve as a guide only. Detailed drawings and specification can be obtained by contacting the nearest sales office.*•

Coppercompressionnut*

Coppercompressionnut*

RIGHT ANGLERIGHT ANGLE

RIGHT ANGLERIGHT ANGLE

RIG

HT A

NG

LES

TOP TA

P ME

TER

S

February 2007PRODUCT CATALOGUEPage 22

RIGHT ANGLESTOP TAP METERS

INLINE BALL VALVES

GM76 - Inline Ball Valve: Female - Female (FI - FI)

20 INLINE BALL VALVE FI/FI20 INLINE BALL VALVE FI/FI20 INLINE BALL VALVE FI/FI20 INLINE BALL VALVE FI/FI25 INLINE BALL VALVE FI/FI25 INLINE BALL VALVE FI/FI

202020202525


GM7620GM7620LGM7620LHGM7620LHLCCGM7625GM7625LH

Productcode


GM76 Inline Ball Valve Specification

Product Standard: AS/NZS4796 / MP52-SPEC012Pressure Rating: PN16Potable Water Compliance: AS4020


FemaleOutlet*

STANDARD HANDLELOCKABLE HANDLELONG HANDLEC/W COMPRESSION UNIONSTANDARD HANDLELONG HANDLE

INLIN

EB

ALL VA

LES


Product Type - Inline Ball Valve


Standard lockable handle shown

GM76 - Inline Ball Valve: Female - Poly (FI - POLY)

20 INLINE BALL VALVE FI/POLY20 INLINE BALL VALVE FI/POLY20 INLINE BALL VALVE FI/POLY20 INLINE BALL VALVE FI/POLY25 INLINE BALL VALVE FI/POLY

2020202025


GM7620PGM7620LPGM7620LPRGM7620LRWGM7625LP

Productcode




NOTE:Refer to thread standard Series 'RP' Sealing Internal Parallel Thread. Refer to AS1722.1 for further details.The illustration shown is intended to serve as a guide only. Detailed drawings and specification can be obtained by contacting the nearest sales office.*•


STANDARD HANDLELONG HANDLELONG HANDLE RED THIMBLELONG LILAC HANDLE RED THIMBLELONG HANDLE

‘A’


FemaleInlet*

PolyOutlet

Standard (Blue) thimbleshown. (Red thimble

option available)

FemaleInlet*

GM7620POption P - Inline Ball Valvewith Poly outlet




‘A’

GM76 - Inline Ball Valve: Male - Female (MI - FI)

20 INLINE BALL VALVE MI/FI20 INLINE BALL VALVE MI/FI20 INLINE BALL VALVE MI/FI20 INLINE BALL VALVE MI/FI20 INLINE BALL VALVE MI/FI25 INLINE BALL VALVE MI/FI

202020202025


GM76A20GM76A20AUCGM76A20LGM76A20LHGM76A20LRWGM76A25

Productcode




FemaleOutlet*

STANDARD HANDLEC/W COMPRESSION UNIONLOCKABLE HANDLELONG LOCKABLE HANDLELONG LILAC HANDLE LOCKABLESTANDARD HANDLE

‘A’


GM76 - Inline Ball Valve: Male - Poly (MI - POLY)

20 INLINE BALL VALVE MI/POLY20 INLINE BALL VALVE MI/POLY20 INLINE BALL VALVE MI/POLY

202020


GM76A20PGM76A20LPGM76A20LPW

Productcode





NOTE:Refer to thread standard Series 'RP' Sealing Internal Parallel Thread. Refer to AS1722.1 for further details.Refer to thread standard Series 'R' Sealing Pipe Thread External Taper Pipe Thread. Refer to AS1722.1 for further details.The illustration shown is intended to serve as a guide only. Detailed drawings and specification can be obtained by contacting the nearest sales office.

***•

STANDARD HANDLELONG HANDLELONG BLUE HANDLE LOCAKABLE


MaleInlet**

PolyOutlet Male

Inlet*

Option P - Inline Ball Valvewith Poly outlet

GM76A20P


Product Type - Poly Outlet



GM76A20


Product Type - Female Outlet




INLIN

EB

ALL VA

LES

INLINE BALL VALVES

‘A’Standard (Blue) thimbleshown. (Red thimble

option available)

RIGHT ANGLEBALL VALVES

GM77 - Right Angle Ball Valve: Female - Female (FI - FI)

20 R/ANGLE BALL VALVE FI/FI20 R/ANGLE BALL VALVE FI/FI20 R/ANGLE BALL VALVE FI/FI25 R/ANGLE BALL VALVE FI/FI

20202025


GM7720GM7720LHGM7720LHRWGM7725

Productcode


GM77Right Angle Ball Valve Specification



FemaleInlet*

STANDARD HANDLELONG HANDLELONG LILAC HANDLE LOCKABLESTANDARD HANDLE


Product Type - Right Angle Ball Valve


GM77 - Right Angle Ball Valve: Copper Compression - Female (CC - FI)

20 R/ANGLE BALL VALVE CC/FI25 R/AMGLE BALL VALVE CC/FI

2025


GM7720CLGM7725CL

Productcode


GM77 Right Angle Ball Valve Specification


NOTE:Refer to thread standard Series 'G' Fastening Pipe Thread Internal Thread & Series 'GB' Fastening Pipe Thread External Thread Class B. Refer to AS1722.1 for further details.Refer to thread standard Series 'RP' Sealing Internal Parallel Thread. Refer to AS1722.1 for further details.The illustration shown is intended to serve as a guide only. Detailed drawings and specification can be obtained by contacting the nearest sales office.

***•

STANDARD HANDLESTANDARD HANDLE



FemaleOutlet*

Standard lockablehandle shown

CopperCompression

Inlet*

FemaleOutlet**

GM7720CLOption CL - Copper

Compression inletwith Female outlet




RIG

HT A

NG

LEB

ALL VA

LES

‘A’

‘A’


NOTE:Refer to thread standard Series 'G' Fastening Pipe Thread Internal Thread & Series 'GB' Fastening Pipe Thread External Thread Class B. Refer to AS1722.1 for further details.Refer to thread standard Series 'RP' Sealing Internal Parallel Thread. Refer to AS1722.1 for further details.The illustration shown is intended to serve as a guide only. Detailed drawings and specification can be obtained by contacting the nearest sales office.

***•

CopperCompression

Inlet*

GM77 - Right Angle Ball Valve: Female - Male (FI - MI)

20 R/ANGLE BALL VALVE FI/MI20 R/ANGLE BALL VALVE FI/MI25 R/ANGLE BALL VALVE FI/MI

202025


GM77A20GM77A20LHGM77A25

Productcode


GM77 Right Angle Ball Valve Specification


FemaleInlet*

STANDARD HANDLELONG HANDLESTANDARD HANDLE


GM77 - Right Angle Ball Valve: Copper Compression - Male (CC - MI)

20 R/ANGLE BALL VALVE CC/MI25 R/ANGLE BALL VALVE CC/MI

2025


GM7720CMGM7725CM

Productcode






MaleOutlet**

MaleOutlet**

GM7720CMOption CM - Copper

Compression inletwith Male outlet




GM77A20Nominal Diameter - Ø20mm

Product Type - Female Inlet



‘A’

‘A’

NOTE:Refer to thread standard Series 'RP' Sealing Internal Parallel Thread. Refer to AS1722.1 for further details.Refer to thread standard Series 'R' Sealing Pipe Thread External Taper Pipe Thread. Refer to AS1722.1 for further details.The illustration shown is intended to serve as a guide only. Detailed drawings and specification can be obtained by contacting the nearest sales office.

***•


RIGHT ANGLEBALL VALVES

RIG

HT A

NG

LEB

ALL VA

LES

DUALCHECK VALVE

GM78 - Dual Check Valve


20 DUAL CHECK VALVE 20


GM7820

Productcode


NOTE:The illustration shown is intended to serve as a guide only. Detailed drawings and specification can be obtained by contacting the nearest sales office.•

OU

T

DU

AL

CH

EC

K VA

LVE

‘A’

GM78 Dual Check Valve Specifications

Pressure Rating: PN16Potable Water Compliance: AS4020


Product Type - Dual Check Valve

Product Code Specification:Inlet

Outlet

GM78A20 - 20mm TAPPING SET BALL VALVE KIT - WITH TERMINATION BOX

Kit Content:

20 INLINE BALL VALVE FI/POLY20 INLINE BALL VALVE MI/FITERMINATION BOX

GM7620PGM76A20PC5535.BC*

Component Code Content Description

111

QTY

STANDARD HANDLESTANDARD HNDLE

GM78A20

Product Code:

TERMINATION BOX GM7620P - 20MM INLINE BALL VALVE FI/POLY

GM76A20P - 20MM INLINEBALL VALVE MI/POLY

20 INLINE BALL VALVE FI/POLY20 INLINE BALL VALVE MI/FI

GM7620PGM76A20P


11

QTY


GM78A20A - 20mm TAPPING SET BALL VALVE KIT - WITHOUT TERMINATION BOX

Kit Content:

GM78A20A

Product Code:

GM7620P - 20MM INLINE BALL VALVE FI/POLY


GM78B20 - 20mm METER SET (VIC)

Kit Content:

20 R/ANGLE BALL VALVE CC/FI20 DUAL CHECK VALVE20 R/ANGLE ELBOW COPPER COMPRESSION/MI

GM7720CLGM7820GM7820E*


111

QTY

STANDARD HANDLE

GM78B20

Product Code:

GM7720CL - 20MM R/ANGLEBALL VALVE CC/FI

GM7820 - 20MM DUAL CHECK VALVE

20MM R/ANGLE ELBOW COPPER COMPRESSION/MI

NOTE:Component is available with kit only.For individual component details, refer to corresponding product section in this catalogue.The illustration shown is intended to serve as a guide only. Detailed drawings and specification can be obtained by contacting the nearest sales office.

*••


BA

LL VALV

EK

ITS

BALL VALVEKITS

METER CON 20MM UNION X 20MM MALE THREAD

3/4”OD COPPER SOLDEREDX 3/4”MI ELBOW

3/4”OD COPPER SOLDERED X 3/4”MI STRAIGHT CONNECT

Kit Content:

GM78B20S

Product Code:

GM77A20LH - 20MM R/ANGLE BALL VALVE FI/MI

GM7720LHRW - 20MMR/ANGLE BALL VALVE FI/FI

20MM SHORT RADIUSSOLDERED BEND


*••

BALL VALVEKITS


BA

LL VALV

EK

ITS

GM78B20S - 20mm METER SET (NSW)

20 R/ANGLE BALL VALVE FI/MI20 R/ANGLE BALL VALVE FI/FI20 SHORT RADIUS SOLDERED BENDMETER CON 20MM UNION X 20MM MALE THREAD3/4”OD COPPER SOLDERED X 3/4”MI ELBOW3/4”OD COPPER SOLDERED X 3/4”MI STRAIGHT CONNECT

GM77A20LHGM7720LHRWGM7820SRSB*GM7820U*GM7020SC*GM7820SC*


111112

QTY

LONG LOCKABLE HANDLELONG LILAC HANDLE

GM79A20 - 20mm HOUSE SERVICE KIT FOR PE

Kit Content:

20 INLINE BALL VALVE FI/POLY20 INLINE BALL VALVE MI/FICONNECTOR 3/4” MI BSP X 25MM POLY

GM7620LPRGM76A20GM86B2025R*


111

QTY

LONG HANDLE RED THIMBLESTANDARD HANDLERED THIMBLE

GM79A20

Product Code:

GM7620LPR - 20MM INLINEBALL VALVE FI/POLY

GM76A20 - 20MM INLINEBALL VALVE MI/FI

CONNECTOR3/4”MI BSP X 25MM POLY

Long Handle

Long Handle

Long Handle

Red Thimble

RedThimble


*••

GM79A20CRQ - 20mm POLY BALL VALVE KIT

Kit Content:

20 INLINE BALL VALVE FI/POLY20 INLINE BALL VALVE MI/POLY25 THIMBLE RT2

GM7620PGM76A20PFC40020*


112

QTY

STANDARD HANDLESTANDARD HANDLERED THIMBLE

GM79A20CRQ

Product Code:

GM7620P - 20MM INLINEBALL VALVE FI/POLY


25MM THIMBLE RT2

GM8020 - 20mm HOUSE CONNECTION KIT (TAS)

Kit Content:

20 INLINE BALL VALVE FI/FI20 INLINE BALL VALVE MI/FICONNECTOR 20MM BSP X 20MM COPPER SOLDERED

GM7620LHGM76A20GM86C20*


112

QTY

LONG HANDLESTANDARD HANDLE

GM8020

Product Code:

GM7620LH - 20MM INLINEBALL VALVE FI/FI

GM76A20 - 20MM INLINEBALL VALVE MI/FI

CONNECTOR 20MM BSP X 20MM COPPER SOLDERED

Long Handle

BA

LL VALV

EK

ITS


BALL VALVEKITS

Norcast Tapping Machine

Norcast Tapping Machine Specifications: This is a hand-operated machine designed to facilitate the tapping of service connections in pressurised water mains without interruption to the service. Three Gunmetal Adaptors are supplied with the machine to suit the variations in tapping sizes as well as two masonry drills which are suitable for tapping A.C., C.I. and D.I. pipes. Fluted hole drills are available for use with P.E. and P.V.C. pipes. Note: Replacement drill bits are available on request.


ACCESSORIES

15mm 20mm 25mm 32mm 40mm 50mm

C2191.05C2191.06

Product code

NORCAST SERVICE TAPPING MACHINENORCAST SUPER TAPPING MACHINE

Description Tapping Sizes

Lip Seal Replacement

Square inner edgeof lip seal

Sharp outer edgeGMOR60780GMOR60790

Product Code

SMALL NITRILE LIP SEALLARGE NITRILE LIP SEAL

Description

20, 25 & 3240 & 50

SuitsTapping Size

Note: For tapping bands to suit pipe up to nominal 200mm outside diameter only. If the nominal pipe outside diameter is 200mm or greater then use ‘O’ ring seal replacement GMOR60790 regardless of the tapping size.

‘O’ Ring Seal Replacement

GMOR60038GMOR60041GMOR60062

Product Code

38 X 8 NITRILE ‘O’ RING41 X 8.5 NITRILE ‘O’ RING62 X 11 NITRILE ‘O’ RING

Description

1520, 25 & 32

40 & 50

SuitsTapping Size

Note: For tapping bands to suit pipe up to nominal 200mm outside diameter only. If the nominal pipe outside diameter is 200mm or greater then use ‘O’ ring seal replacement GMOR60062 regardless of the tapping size.

milnes front cover.ai

Documents