outsulation smd system installation details (formerly ... · outsulation smd system installation...

OUTSULATION® SMD SYSTEM™

(Formerly SPRINT® MD SYSTEM®)

An Exterior Wall Insulation and Finish System With Moisture Drainage

Outsulation SMD System Installation Details

(Formerly Sprint MD System)

DS163

MINOR PENETRATIONS OSMD 0.0.28

4RS

REV:APPROVED BY:

02/09

DATE:

Outsulation SMD System

of any project. The project design professional determines, in its sole

version.

®

is best suited for the project. Use of a functionally equivalent detail

without notice. Contact Dryvit to insure you have the most recent does not violate Dryvit's warranty. This detail is subject to change

discretion, whether this detail or a functionally equivalent alternative

The architecture, engineering and design of the project using the

standards. This detail is for general information and guidance only

this detail and for the architecture, design, engineering or workmanship and Dryvit specifically disclaims any liability for the use of

professional. All systems must comply with local building codes and Dryvit products is the responsibility of the project's design

OSMD 0.0.34GABLE END WITH WOOD TRIM

OSMD 0.0.37CHIMNEY ENCLOSUREOSMD 0.0.36OSMD 0.0.35TERMINATION AT PARAPET

TERMINATION AT ROOF-TO-WALL FLASHING

SOFFIT TERMINATION OSMD 0.0.31OSMD 0.0.32OSMD 0.0.33

SOFFIT WITH FRIEZE BOARDGABLE END WITH EIFS TRIM

OSMD 0.0.30OSMD 0.0.29WOOD FRAMED DECK - CROSS SECTION

WOOD FRAMED DECK - CUT AWAY

OSMD 0.0.05FASTENING

ARCHED WINDOW HEAD OSMD 0.0.16

OSMD 0.0.22DOOR HEAD WITH INTEGRAL FLASHING

OSMD 0.0.25SYSTEM CONFIGURATION AT OPENINGSOSMD 0.0.26OSMD 0.0.27

SHUTTER AND DOWN SPOUT ATTACHMENTAESTHETIC REVEALS

OSMD 0.0.23OSMD 0.0.24

DOOR HEAD WITH BRICK MOLDINSIDE / OUTSIDE CORNERS

OSMD 0.0.19WINDOW SILL

OSMD 0.0.21OSMD 0.0.20DOOR JAMB WITH INTEGRAL FLASHING

DOOR JAMB WITH BRICK MOLD

OSMD 0.0.17OSMD 0.0.18

WINDOW HEADWINDOW JAMB

OSMD 0.0.11SEALANT CONFIGURATION OPTIONS

OPENING PREP - OSMD 0.0.14

OSMD 0.0.15BACKSTOP® NT WRB/ GRID TAPE™ OPTIONWINDOW ELEVATION

OSMD 0.0.13OSMD 0.0.12

OPENING PREP - BACKSTOP® NT WRB/ AQUAFLASH® SYSTEM OPTION

OPENING PREP - SHEET TYPE WRB

OSMD 0.0.08TERMINATION ABOVE GRADE

OSMD 0.0.10OSMD 0.0.09

VERTICAL EXPANSION JOINTSEXPANSION JOINT AT FLOOR LINE

OSMD 0.0.06OSMD 0.0.07FASTENING PATTERN - OUTSIDE CORNER

FASTENING PATTERN

OSMD 0.0.02DRYVIT DRAINAGE MAT™ OPTION

OSMD 0.0.04OSMD 0.0.03

OUTSIDE CORNER - HIGH IMPACTDUPONT™ TYVEK® STUCCOWRAP® OPTION

OSMD 0.0.01OUTSULATION SMD SYSTEM

TABLE OF CONTENTS

® ™

RS 02/094

DATE:REV:APPROVED BY:


this detail and for the architecture, design, engineering or workmanship

without notice. Contact Dryvit to insure you have the most recent

®

version.


is best suited for the project. Use of a functionally equivalent detail does not violate Dryvit's warranty. This detail is subject to change



professional. All systems must comply with local building codes and

and Dryvit specifically disclaims any liability for the use ofstandards. This detail is for general information and guidance only

Dryvit products is the responsibility of the project's design


WOOD OR STEEL FRAMING

DRYVIT REINFORCING MESH

WRAP DRYVIT DETAILMESH® 51 MM (2") MIN.AT BACKSIDE OF INSULATION BOARD

Drainage TrackOption

DRYVIT FINISHDRAINAGE STRIP

DRYVIT GENESIS, GENESIS DMOR GENESIS DMS BASE COAT

DRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENER

DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COAT

APPROVED OSMD SYSTEM INSULATION BOARD

DRYVIT MD SPACERCODE APPROVED WATER-RESISTIVE BARRIER

SUBSTRATE

OSMD 0.0.01

® ™

™

4 02/09RS

REV: DATE:APPROVED BY:



version.


does not violate Dryvit's warranty. This detail is subject to change




®


and Dryvit specifically disclaims any liability for the use of


professional. All systems must comply with local building codes and standards. This detail is for general information and guidance only

Dryvit Drainage Mat™ Option





DRYVIT GENESIS, GENESIS DMOR GENESIS DMS BASE COATDRYVIT FINISH




CODE APPROVED WATER-RESISTIVE BARRIER

DRYVIT DRAINAGE MAT

SUBSTRATE

OSMD 0.0.02

® ™

REV:

RS

APPROVED BY:

02/09

DATE:

5


version.

®

is best suited for the project. Use of a functionally equivalent detail does not violate Dryvit's warranty. This detail is subject to change without notice. Contact Dryvit to insure you have the most recent

discretion, whether this detail or a functionally equivalent alternative of any project. The project design professional determines, in its sole

2.1. DRYVIT DRAINAGE STRIP IS REQUIRED WHENUSING STUCCOWRAP WITHOUT A DRAINAGETRACK.

THE SELECTION OF A SPECIFICWATER-RESISTIVE BARRIER IS THERESPONSIBILITY OF THE SPECIFIER AND ISOUTSIDE THE SCOPE OF THIS DOCUMENT.


standards. This detail is for general information and guidance only and Dryvit specifically disclaims any liability for the use of


Dryvit products is the responsibility of the project's design professional. All systems must comply with local building codes and

NOTE:

Dupont Tyvek StuccoWrap Option

SUBSTRATE

DRYVIT FINISH


DRYVIT DRAINAGE STRIP(SEE NOTE 2)

WRAP DRYVIT DETAIL MESH® 51 MM (2") MIN.AT BACKSIDE OF INSULATION BOARD


DRYVIT REINFORCING MESHDRYVIT GENESIS, GENESIS DMOR GENESIS DMS BASE COAT



DUPONT TYVEK STUCCOWRAP(REFER TO NOTES 1,2)


OSMD 0.0.03

® ™ ® ®

™

™

02/09RS 4

DATE:APPROVED BY: REV:

Outsulation SMD SystemDRYVIT RECOMMENDS THAT GROUND FLOORAPPLICATIONS AND ALL FACADES EXPOSEDTO ABNORMAL STRESS, HIGH TRAFFIC, ORDELIBERATE IMPACT HAVE THE BASE COATREINFORCED WITH PANZER® MESH PRIORTO STANDARD MESH™ OR STANDARD PLUSMESH™. LOCATION OF HIGH IMPACT ZONESSHOULD BE INDICATED ON CONTRACTDRAWINGS.

1.NOTE:


version.

®




REFER TO DETAILS OSMD 0.0.01, 0.0.02 AND0.0.03 FOR SYSTEM CONFIGURATION OPTIONS.

2. The architecture, engineering and design of the project using the


standards. This detail is for general information and guidance only professional. All systems must comply with local building codes and



Outside Corner- High Impact

203 MM (8") MIN.

DRYVIT MD SPACER

APPROVED OSMD SYSTEMINSULATION BOARD

DRYVIT STANDARD OR STANDARDPLUS REINFORCING MESH OVERLAPMIN. 203 MM (8") AT CORNER

DRYVIT FINISH



DRYVIT CORNER MESH


DRYVIT INTERMEDIATE MESH

CODE APPROVEDWATER-RESISTIVE BARRIER

SUBSTRATE

OSMD 0.0.04

® ™

™

19 MM (3/4") MIN.

4RS 02/09

REV:APPROVED BY: DATE:



version.


does not violate Dryvit's warranty. This detail is subject to change is best suited for the project. Use of a functionally equivalent detail


®






1. FOR NON-NAILABLE SHEATHINGSUBSTRATES, THE FASTENER MUST BEINSTALLED INTO THE FRAMING.

NOTE:

Fastening

APPROVED WASHERSUBSTRATE

25 MM (1") MIN.

MINIMUM 4.8 MM (3/16") DIAMETERCORROSION RESISTANT MASONRY SCREWAPPROVED OSMD SYSTEM INSULATIONBOARD

CONCRETE

MINIMUM NO. 6 CORROSIONRESISTANT SCREW

MINIMUM 12 GAUGE (8d) CORROSIONRESISTANT RING SHANK NAIL

NAILABLESUBSTRATE APPROVED OSMD SYSTEM INSULATION

BOARDMINIMUM NO. 6 CORROSIONRESISTANT SCREWNAILABLE SUBSTRATE

25 MM (1") MIN.

APPROVED WASHER

GYPSUM SHEATHING OR OTHERNON- NAILABLE SUBSTRATE

9.5 MM (3/8") MIN.

APPROVED WASHERMINIMUM NO. 6 SELF DRILLINGCORROSION RESISTANT SCREWAPPROVED OSMD SYSTEM INSULATIONBOARD

NON-NAILABLESUBSTRATESTEEL FRAMING

APPROVED WASHER19 MM (3/4") MIN.

25 MM (1") MIN.

GYPSUM SHEATHING OR OTHERNON- NAILABLE SUBSTRATEAPPROVED WASHERMINIMUM 12 GAUGE (8d) CORROSIONRESISTANT RING SHANK NAILAPPROVED OSMD SYSTEM INSULATIONBOARD

NON-NAILABLESUBSTRATEWOOD FRAMING

OSMD 0.0.05

® ™

DRAINAGE TRACK25 MM. (1") TYP.

APPROVED BY:

RS

REV:

4

DATE:

02/09

Outsulation SMD System Fastening Pattern


version.

®

does not violate Dryvit's warranty. This detail is subject to change without notice. Contact Dryvit to insure you have the most recent

is best suited for the project. Use of a functionally equivalent detail discretion, whether this detail or a functionally equivalent alternative

1. REFER TO DETAILS OSMD 0.0.01, 0.0.02 AND0.0.03 FOR SYSTEM CONFIGURATIONOPTIONS.





NOTE:The architecture, engineering and design of the project using the


VERTICAL INSULATION BOARDJOINT ALIGNED WITHDRYVIT MD SPACER

DRYVIT MD SPACER 3.2 MM X 76 MM (1/8" X 3")SPACED DIRECTLY BEHIND LINE OF FASTENERS

305 MM. (12")TYP. PERIMETER



SUBSTRATE

305 MM. (12")O.C. TYP.



406 MM. (16")O.C. TYP.

OSMD 0.0.06

® ™

™

OFFSET INSULATION BOARDEDGES AT CORNERS


1.NOTE:

REV:

4RS

APPROVED BY: DATE:

02/09

Fastening Pattern - Outside Corner


version.

®




2. CORNER MESH MAY BE USED IN ADDITION TODRYVIT REINFORCING MESH.




this detail and for the architecture, design, engineering or workmanship 3. REFER TO DETAILS OSMD 0.0.01, 0.0.02 AND

0.0.03 FOR SYSTEM CONFIGURATION OPTIONS.


DRYVIT REINFORCING MESHOUTSIDE CORNER (SEE NOTE 2)


406 MM(16") TYP.

OFFSET VERTICAL JOINTS

25 MM (1") FROM BOARD EDGE (TYP.)



305 MM(12") TYP.

DRYVIT MD SPACER PLACEDDIRECTLY BEHIND ROW OF FASTENERS

OSMD 0.0.07

® ™

™


4RS 02/09

Outsulation SMD System Termination Above Grade

DRYVIT RECOMMENDS THAT GROUND FLOORAPPLICATIONS AND ALL FACADES EXPOSEDTO ABNORMAL STRESS, HIGH TRAFFIC, ORDELIBERATE IMPACT HAVE THE BASE COATREINFORCED WITH PANZER® MESH PRIORTO STANDARD MESH™ OR STANDARD PLUSMESH™. LOCATION OF HIGH IMPACT ZONESSHOULD BE INDICATED ON CONTRACTDRAWINGS.


version.

®


discretion, whether this detail or a functionally equivalent alternative is best suited for the project. Use of a functionally equivalent detail

FLOOR LINE EXPANSION JOINT IS REQUIRED IF610 MM (24") DIMENSION IS EXCEEDED.

2.1.

3. REFER TO DETAILS OSMD 0.0.01, 0.0.02 AND0.0.03 FOR SYSTEM CONFIGURATION OPTIONS.

NOTE:Dryvit products is the responsibility of the project's design





WRAP DRYVIT DETAILMESH® TO BACKSIDEOF EPS MIN. 51 MM (2")

DRAINAGE STRIP

CODE APPROVED WATER-RESISTIVEBARRIER LAPPED INTO DRAINAGE TRACKDRYVIT MD SPACER LAPPED OVERFLANGE OF DRAINAGE TRACKAPPROVED OSMD SYSTEM INSULATION BOARD

51 MM (2") MIN.610 MM (24") MAX. (SEE NOTE 2)

SEALANT WITHBOND BREAKER,

BY OTHERS

NOTCH INSULATION BOARDTO ACCOMMODATE TRACK,

WATER-RESISTIVE BARRIER,AND SPACER.

203 MM (8") MIN. ABOVE FINISHED GRADEOR AS REQUIRED BY LOCAL CODE

Drainage StripOption

SLOPED DRAINAGE TRACK


DRYVIT FINISH

CONCRETE CONSTRUCTION DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COAT

WOOD OR STEEL FRAMINGSUBSTRATE

OSMD 0.0.08

® ™

DRYVIT MD SPACER™



RS 4 02/09

Outsulation SMD System Expansion Joint at Floorline

GAP PLYWOOD TO ALLOW FORCROSS-GRAIN SHRINKAGE OF THE FLOORJOISTS. OFFSET SYSTEM EXPANSION JOINTAPPROXIMATELY 25 MM (1") BELOWPLYWOOD GAP. of any project. The project design professional determines, in its sole

version.

®




2. Dryvit products is the responsibility of the project's design




NOTE:The architecture, engineering and design of the project using the

DRYVIT FINISH

SUBSTRATE


CODE APPROVED WATER-RESISTIVE BARRIERLAPPING OVER FLANGE OF DRAINAGE TRACK

19 MM (3/4") MIN.5

SEE NOTE 1

DRYVIT COMPATIBLE SEALANT WITHCLOSED CELL BACKER ROD,BY OTHERS. (DO NOT BLOCK TRACKDRAIN HOLES)

INSULATION BOARD TO ACCOMMODATEDRAINAGE TRACK, WATER-RESISTIVE

BARRIER, AND SPACER


APPROVED OSMD SYSTEM INSULATION BOARDSLOPE TOP EDGE

DRYVIT DEMANDIT® OR COLOR PRIME™ON SURFACE(S) TO RECEIVE SEALANT

1

DRYVIT MD SPACER™ LAPPEDOVER FLANGE OF DRAINAGE TRACK

DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COAT


OSMD 0.0.09

® ™

CONCRETECONSTRUCTION


4RS 02/09

Outsulation SMD System Vertical Expansion Joints


1.NOTE:


version.

®










CORROSIONRESISTANT "L" TRIM

CODE APPROVED WATER-RESISTIVEBARRIER PUSHED INTO JOINT

TO ACCOMMODATE MOVEMENT

WRAP DRYVIT DETAILMESH® 51 MM (2") MIN. ATBACKSIDE OF INSULATION BOARD

DRYVIT DEMANDIT® ORCOLOR PRIME™ ON

SURFACE(S) TO RECEIVE SEALANT

19 MM (3/4") MIN. DRYVIT COMPATIBLE SEALANTWITH CLOSED CELL BACKER ROD,BY OTHERS

OPTION

WRAP DRYVIT DETAIL MESH51 MM (2") MIN. AT BACKSIDE

OF INSULATION BOARD

DRYVIT APPROVED WASHERWITH CORROSION RESISTANT

FASTENER


DRYVIT FINISH

DRYVIT MD SPACER



OSMD 0.0.10

® ™



4RS 02/09

Outsulation SMD System Sealant Configuration Options

WEATHER SEAL JOINTS SUCH AS AT WINDOWAND DOOR PERIMETERS CAN USE ANGLE ORRECTANGULAR BEADS. RECTANGULAR BEADSUSED AS A WEATHERSEAL REQUIRE A MINIMUM12.7 MM (1/2") WIDTH. of any project. The project design professional determines, in its sole

version.

®



EXPANSION JOINTS SHALL USE RECTANGULARBEADS AND BE DESIGNED FOR MINIMUM FOURTIMES THE ANTICIPATED MOVEMENT, BUT NOTLESS THAN 19 MM (3/4").

1. 2.NOTE:





w

t = 6.4 mm (1/4") min.w/t = 2:1

FOR RECTANGULAR BEADS:w = 12.7 mm (1/2") min. (SEE NOTES 1 AND 2)

WRAP DRYVIT DETAIL MESH51 MM (2") MIN. AT BACKSIDEOF INSULATION BOARD




DRYVIT COMPATIBLE SEALANT WITHQUARTER ROUND BACKER ROD, BY OTHERS(REFER TO BOND BREAKER OPTIONS BELOW)

TRIANGULAR BACKER ROD BOND BREAKER TAPEof abutting material but not

DRYVIT DEMANDIT OR COLOR PRIMEON SURFACE(S) TO RECEIVE SEALANT

DRYVIT COMPATIBLE SEALANTWITH CLOSED CELL BACKER ROD,BY OTHERS

DRYVIT REINFORCING MESH EMBEDDED INDRYVIT GENESIS, GENESIS DMOR GENESIS DMS BASE COAT

t

RectangularBead

less than 3.2 mm (1/8")

WRAP DRYVIT DETAIL MESH®51 MM (2") MIN. AT BACKSIDEOF INSULATION BOARD

Angle Bead BondBreaker Options

w

t = 6.4 mm (1/4") min.w = specified by manufacturer

FOR ANGLE BEADS:

tt

AngleBead

t

OSMD 0.0.11

® ™

APPROVED BY: REV: DATE:

02/091RS

Outsulation SMD System Opening Prep -Sheet Type Water-Resistive Barrier

2. SHEET TYPE CODE APPROVEDWATER-RESISTIVE BARRIER SHALL BEINSTALLED IN A WEATHER BOARD FASHIONIN ACCORDANCE WITH CODE ANDMANUFACTURER'S REQUIREMENTS.


version.

®



Dryvit products is the responsibility of the project's design INSTALL WINDOW UNIT AND ASSOCIATEDFLASHINGS PER MANUFACTURER'SRECOMMENDATIONS, CODE REQUIREMENTSAND PROJECT DOCUMENTS. and Dryvit specifically disclaims any liability for the use of

this detail and for the architecture, design, engineering or workmansh


NOTE:1. The architecture, engineering and design of the project using the

INSTALL WINDOW UNIT AND ASSOCIATED FLASHINGSPER MANUFACTURER'S RECOMMENDATIONS, CODEREQUIREMENTS AND PROJECT DOCUMENTS.FOLD DOWN WATER-RESISTIVE BARRIER OVERHEAD FLASHING AND TAPE SEAMS WITH DRYVITFLASHING TAPE

STEP #3

3.)

APPLY DRYVIT FLASHING TAPE AND SURFACECONDITIONER ONTO HEAD AND LAP CODEAPPROVED SHEET TYPE WATER-RESISTIVEBARRIER OVER IN A WEATHER BOARD FASHION

2.)

1.)

CUT AND FOLD BACK CODE APPROVEDWATER-RESISTIVE BARRIER AT HEAD

SEE NOTE 2

4" MIN.

INSTALL DIAGONAL STRIPS OF DRYVIT FLASHINGTAPE AND SURFACE CONDITIONER AT CORNERSOVER PREVIOUSLY INSTALLED FLASHING TAPEAND WATER-RESISTIVE BARRIER

STEP #1 STEP #2

APPLY DRYVIT FLASHING TAPEAND SURFACE CONDITIONER ONTOJAMB AND OVER CODE APPROVEDSHEET TYPE WATER-RESISTIVEBARRIER

APPLY DRYVIT FLASHING TAPEAND SURFACE CONDITIONER™ ONTOSILL AND UP JAMBS LAPPING OVERCODE APPROVED SHEET TYPEWATER-RESISTIVE BARRIER 6" MIN.

(typ)

OSMD 0.0.12

® ™

DATE:REV:APPROVED BY:

RS 02/092

Outsulation SMD System NOTE:

Opening Prep - Backstop® NT WRB/AquaFlash® System Option

4. APPLY CAULK BEHIND HEAD AND JAMBFLANGES OF WINDOW.

SHEET TYPE CODE APPROVEDWATER-RESISTIVE BARRIER MAY BE USEDAND SHALL BE INSTALLED IN A WEATHERBOARD FASHION IN ACCORDANCE WITH CODEAND MANUFACTURER'S REQUIREMENTS.


version.

®




2. DRYVIT OPENING WRAP SHALL EXTEND TOINTERIOR FACE OF FRAMING.

3.1. APPLY DRYVIT BACKSTOP NT/-SMOOTHOR TEXTURE OVER REMAINDER OF WALLSURFACE.


and Dryvit specifically disclaims any liability for the use of this detail and for the architecture, design, engineering or workmanship



STEP #4STEP #3

APPLY DRYVIT AQUAFLASHSYSTEM AT HEAD LAPPINGOVER JAMB APPLICATION

APPLY DRYVIT AQUAFLASHSYSTEM AT JAMBS LAPPINGOVER SILL APPLICATION

DRYVIT WATER-RESISTIVEBARRIER COATING(SEE NOTE 3)

STEP #2STEP #1

INSTALL DIAGONAL STRIPOF DRYVIT AQUAFLASHSYSTEM AT CORNERS(JAMB AND SILL)

APPLY DRYVIT AQUAFLASHSYSTEM AT SILL, EXTENDINGUP JAMBS MINIMUM 2 12"

OSMD 0.0.13

® ™


APPLY DRYVIT FLASHING TAPE SURFACECONDITIONER AND DRYVIT FLASHING TAPEAT SILL, INCLUDING CORNER SPLICES. 02/091RS

Outsulation SMD System Opening Prep - Backstop® NT WRB/Backstop NT / Grid Tape™ Option


TROWEL APPLY DRYVIT BACKSTOP NT-TEXTURE OVER THE DRYVIT GRID TAPE ALLTHE WAY TO INSIDE FACE OF OPENING. ALLVOIDS MUST BE FILLED; MULTIPLE PASSES MAYBE REQUIRED. AS AN OPTION, DRYVIT GRIDTAPE AND DRYVIT BACKSTOP NT-TEXTUREMAY ALSO BE APPLIED AT THE SILL PRIOR TODRYVIT FLASHING TAPE APPLICATION.

APPLY DRYVIT BACKSTOP NT - SMOOTHOR TEXTURE OVER REMAINDER OF WALLSURFACE.SHEET TYPE CODE APPROVEDWATER-RESISTIVE BARRIER MAY BE USEDAND SHALL BE INSTALLED IN A WEATHERBOARD FASHION IN ACCORDANCE WITH CODEAND MANUFACTURER'S REQUIREMENTS.3.

6.

®

does not violate Dryvit's warranty. This detail is subject to change without notice. Contact Dryvit to insure you have the most recent version.


INSTALL WINDOW UNIT AND ASSOCIATEDFLASHINGS PER MANUFACTURER'SRECOMMENDATIONS, CODE REQUIREMENTSAND PROJECT DOCUMENTS.

APPLY DRYVIT GRID TAPE ON CORNERS OFOPENING AND SHEATHING JOINTS.

5.2.

4. NOTE:1.


and Dryvit specifically disclaims any liability for the use ofthis detail and for the architecture, design, engineering or workmanship



DRYVIT WATER RESISTIVEBARRIER COATING APPLIEDTO FACE OF WALL(SEE NOTE 5)

APPLY DRYVIT FLASHING TAPEAND SURFACE CONDITIONER(SEE NOTES 2 AND 3)

STEP #3 STEP #4

4" MIN.

6" MIN.(typ)

STEP #1 STEP #2

APPLY DRYVIT GRID TAPE(SEE NOTES 1 AND 2)

TROWEL APPLY DRYVITBACKSTOP NT-TEXTURE(SEE NOTE 2)

OSMD 0.0.14

® ™

APPLY SEALANTTO FLASHING

JUNCTION

FLASHING INTEGRALWITH WINDOW


4RS 02/09

Outsulation SMD System Window Elevation


®


version.without notice. Contact Dryvit to insure you have the most recent

is best suited for the project. Use of a functionally equivalent detail discretion, whether this detail or a functionally equivalent alternative

FLASHING TRANSITION BETWEEN CURVEDAND HORIZONTAL ASSEMBLIES MUST BEPROPERLY LAPPED AND SEALED TO SHEDWATER TO THE EXTERIOR.




NOTE:1. The architecture, engineering and design of the project using the

FLASHINGINTEGRAL

WITH WINDOW

OSMD 0.0.15

® ™

ARCHED WINDOW WITHINTEGRAL FLASHING

SUBSTRATE

FRAMING


RS 4 02/09

Outsulation SMD System Arched Window Head


®


without notice. Contact Dryvit to insure you have the most recent version.

FOR NON-NAILABLE SHEATHINGSUBSTRATES, FASTENERS MUST BEINSTALLED INTO THE FRAMING.




of any project. The project design professional determines, in its sole this detail and for the architecture, design, engineering or workmanship

The architecture, engineering and design of the project using the NOTE:1.

6APPROVED OSMD SYSTEM INSULATION BOARDOR EPS TRIM (OPTIONAL) ADHEREDWITH DRYVIT GENESIS, GENESIS DM OR GENESISDMS BASE COAT OR MECHANICALLY FASTENINTO SOLID SUBSTRATE- SLOPE TOP EDGE

WRAP DRYVIT DETAIL MESH®51 MM (2") MIN. AT BACKSIDEOF INSULATION BOARDDRYVIT MD SPACER


DRYVIT COMPATIBLE SEALANT WITHCLOSED CELL BACKER ROD, BY OTHERSPROVIDE AIR SEAL AROUND

INTERIOR OF WINDOW PER WINDOWMANUFACTURER'S REQUIREMENTS

12.7 MM (1/2") MIN.

DRYVIT FINISH

DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COATDRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENER

OPENING WRAP (SEEDETAILS OSMD 0.0.12-0.0.14)


CODE APPROVED WATER-RESISTIVEBARRIER LAPPED OVER NAILING FIN

12

OSMD 0.0.16

® ™

WINDOW WITH INTEGRAL FLASHING

SUBSTRATE


4RS 02/09

Outsulation SMD System Window Head

OSMD INSULATION BOARD MAY NEED TO BENOTCHED TO ACCOMMODATEWATER-RESISTIVE BARRIER/ DRAINAGEMEDIUM.


®

does not violate Dryvit's warranty. This detail is subject to change without notice. Contact Dryvit to insure you have the most recent version.


REFER TO DETAILS OSMD 0.0.01, 0.0.02 AND0.0.03 FOR SYSTEM CONFIGURATIONOPTIONS.

2.

NOTE:1.





The architecture, engineering and design of the project using the Dryvit products is the responsibility of the project's design

CODE APPROVED WATER-RESISTIVEBARRIER AND DRAINAGE MEDIUMLAPPED OVER VINYL DRAINAGETRACK (SEE NOTE 2)

APPROVED OSMD SYSTEM INSULATION BOARDOR EPS TRIM (OPTIONAL) ADHEREDWITH DRYVIT GENESIS, GENESIS DM ORGENESIS DMS BASE COAT OR MECHANICALLYFASTEN INTO SOLID SUBSTRATE-SLOPE TOP EDGE


PROVIDE AIR SEAL AROUND INTERIOROF WINDOW PER WINDOW

MANUFACTURER'S REQUIREMENTS


DRYVIT COMPATIBLE SEALANT WITHCLOSED CELL BACKER ROD, BY OTHERS.PROVIDE WEEPS WITH BAFFLES EVERY610 MM (2'-0") ON CENTER


13 MM (1/2") MIN.

DRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENERWRAP DRYVIT DETAIL MESH® 51 MM(2") MIN. AT BACKSIDE OF INSULATION BOARDDRYVIT FINISH



CODE APPROVED WATER-RESISTIVEBARRIER LAPPED OVER NAILING FINAPPROVED OSMD SYSTEM INSULATION BOARD(SEE NOTE 2)DRYVIT MD SPACER

612

OSMD 0.0.17

® ™

APPROVED OSMD SYSTEM INSULATIONBOARD OR EPS TRIM (OPTIONAL)ADHERED WITH DRYVIT GENESIS,GENESIS DM OR GENESIS DMS BASECOAT OR MECHANICALLY FASTEN INTOSOLID SUBSTRATE

WINDOW WITHINTEGRAL FLASHING

DRYVIT DEMANDIT® OR COLOR PRIMEON SURFACE(S) TO RECEIVE SEALANTDRYVIT COMPATIBLE SEALANTWITH CLOSED CELL BACKER ROD,BY OTHERS

4RS 02/09

Outsulation SMD System Window Jamb


®REV:APPROVED BY: DATE:



FOR NON-NAILABLE SHEATHINGSUBSTRATES, THE FASTENER MUST BEINSTALLED INTO THE FRAMING.


and Dryvit specifically disclaims any liability for the use of this detail and for the architecture, design, engineering or workmanship of any project. The project design professional determines, in its sole


NOTE:1. Dryvit products is the responsibility of the project's design




DRYVIT MD SPACER




DRYVIT FINISH12.7 MM (1/2") MIN.

APPROVED OSMD SYSTEM INSULATIONBOARD


SUBSTRATE

OSMD 0.0.18PROVIDE AIR SEAL AROUNDINTERIOR OF WINDOW PER WINDOWMANUFACTURER'S REQUIREMENTS.

® ™

™

™

SUBSTRATE CODE APPROVEDWATER-RESISTIVE BARRIER


RS 4 02/09

Outsulation SMD System Window Sill



®



REFER TO DETAILS OSMD 0.0.01, 0.0.02 AND0.0.03 FOR SYSTEM CONFIGURATION OPTIONS. professional. All systems must comply with local building codes and



Dryvit products is the responsibility of the project's design The architecture, engineering and design of the project using the

NOTE:2.1.

DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COATDRYVIT FINISH

APPROVED SYSTEMINSULATION BOARD

DRYVIT MD SPACER


WINDOW WITH INTEGRAL FLASHING

PROVIDE AIR SEAL AROUNDINTERIOR OF WINDOW PER WINDOWMANUFACTURER'S REQUIREMENTS


WRAP DRYVIT DETAIL MESH®51 MM (2") MIN. AT BACKSIDEOF INSULATION BOARDDRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENERAPPROVED OSMD SYSTEM INSULATIONBOARD OR EPS TRIM (OPTIONAL)ADHERED WITH DRYVIT GENESIS,GENESIS DM OR GENESIS DMS BASECOAT OR MECHANICALLY FASTEN INTOSOLID SUBSTRATE- SLOPE TOP EDGE


13 MM (1/2") MIN.126

OSMD 0.0.19

® ™

™

APPROVED OSMD SYSTEM INSULATIONBOARD OR EPS TRIM(OPTIONAL) ADHERED WITH DRYVITGENESIS, GENESIS DM OR GENESIS DMSBASE COAT OR MECHANICALLY FASTENINTO SOLID SUBSTRATEDOOR WITH INTEGRAL FLASHING

DRYVIT DEMANDIT® ORCOLOR PRIME ON SURFACE(S)TO RECEIVE SEALANTDRYVIT COMPATIBLE SEALANTWITH CLOSED CELL BACKER ROD,BY OTHERS

4RS 02/09

Outsulation SMD System Door Jamb With Integral Flashing



REV:APPROVED BY:

®DATE:




NOTE:1. 2.


and Dryvit specifically disclaims any liability for the use of this detail and for the architecture, design, engineering or workmanship of any project. The project design professional determines, in its sole



DRYVIT MD SPACERSUBSTRATE

OPENING WRAP (SEEDETAILS OSMD 0.0.12-0.0.14)CODE APPROVEDWATER-RESISTIVE BARRIER


DRYVIT FINISH

DRYVIT REINFORCING MESHEMBEDDED IN DRYVIT GENESIS®,GENESIS DM OR GENESIS DMSBASE COAT

12.7 MM (1/2") MIN.

APPROVED SYSTEMINSULATION BOARD



OSMD 0.0.20


® ™

™



APPROVED OSMD SYSTEM INSULATIONBOARD OR EPS TRIM (OPTIONAL)ADHERED WITH DRYVIT GENESIS,GENESIS DM OR GENESIS DMS BASECOAT OR MECHANICALLY FASTEN INTOSOLID SUBSTRATE


DRYVIT FINISH

4RS 02/09

Outsulation SMD System Door Jamb With Brick Mold




®



REFER TO DETAILS OSMD 0.0.01, 0.0.02 AND0.0.03 FOR SYSTEM CONFIGURATION OPTIONS. professional. All systems must comply with local building codes and

of any project. The project design professional determines, in its sole this detail and for the architecture, design, engineering or workmanship and Dryvit specifically disclaims any liability for the use ofstandards. This detail is for general information and guidance only

NOTE:1. 2. Dryvit products is the responsibility of the project's design



SUBSTRATE


DOOR WITHBRICK MOLD

DRYVIT MD SPACER



12.7 MM (1/2") MIN.

DRYVIT DEMANDIT®OR COLOR PRIME™ON SURFACE(S) TO RECEIVE SEALANT

WRAP DRYVIT DETAIL MESH®51 MM (2") MIN. AT BACKSIDE

OF INSULATION BOARD

DRYVIT COMPATIBLE SEALANTWITH CLOSED CELL BACKER ROD

OSMD 0.0.21

® ™

™

DOOR WITH INTEGRALFLASHING

SUBSTRATE

WOOD ORSTEEL FRAMING

4RS 02/09

Outsulation SMD System Door Head With Integral Flashing



®APPROVED BY: REV: DATE:



version.

OSMD INSULATION BOARD MAY NEED TO BENOTCHED TO ACCOMMODATE DRAINAGETRACK AND BARRIER / DRAINAGE MEDIUM.


this detail and for the architecture, design, engineering or workmanship of any project. The project design professional determines, in its sole

standards. This detail is for general information and guidance only and Dryvit specifically disclaims any liability for the use of

2.


NOTE:1.

CODE APPROVED WATER-RESISTIVEBARRIER AND DRAINAGE MEDIUMLAPPED OVER VINYL DRAINAGETRACK (SEE NOTES 1 AND 2)

6 APPROVED OSMD SYSTEM INSULATIONBOARD OR EPS TRIM (OPTIONAL)ADHERED WITH DRYVIT GENESIS,GENESIS DM OR GENESIS DMS BASECOAT OR MECHANICALLY FASTEN INTOSOLID SUBSTRATE- SLOPE TOP EDGE


DRYVIT COMPATIBLE SEALANT WITHCLOSED CELL BACKER ROD. PROVIDEWEEPS WITH BAFFLES 610 MM (2'-0")ON CENTER


12.7 MM (1/2") MIN.

DRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENEROPENING WRAP (SEEDETAILS OSMD 0.0.12-0.0.14)WRAP DRYVIT DETAIL MESH®51 MM (2") MIN. AT BACKSIDEOF INSULATION BOARD

OSMD 0.0.22

DRYVIT MD SPACERAPPROVED OSMD SYSTEM INSULATION BOARDDRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COATDRYVIT FINISH

12


® ™

™

WOOD OR STEELFRAMING

SUBSTRATE

4RS 02/09

Outsulation SMD System Door Head With Brick Mold

OSMD INSULATION BOARD MAY NEED TO BENOTCHED TO ACCOMMODATEWATER-RESISTIVE BARRIER/ DRAINAGEMEDIUM.


REV:APPROVED BY:

®DATE:




2.

NOTE:1.



discretion, whether this detail or a functionally equivalent alternative of any project. The project design professional determines, in its sole



CODE APPROVED WATER-RESISTIVEBARRIER AND DRAINAGE MEDIUMLAPPED OVER VINYL DRAINAGETRACK (SEE NOTES 1 AND 2)

APPROVED OSMD SYSTEM INSULATIONBOARD OR EPS TRIM (OPTIONAL)ADHERED WITH DRYVIT GENESIS,GENESIS DM OR GENESIS DMS BASECOAT OR MECHANICALLY FASTEN INTOSOLID SUBSTRATE- SLOPE TOP EDGE

12.7 MM (1/2") MIN.

DRYVIT COMPATIBLE SEALANT WITH CLOSEDCELL BACKER ROD. PROVIDE WEEPS WITHBAFFLES EVERY 610 MM (2'-0") ON CENTER

DOOR WITHBRICK MOLD


DRIP FLASHING SETIN BED OF SEALANT

OPENING WRAP (SEEDETAILS OSMD 0.0.12-0.0.14)WRAP DRYVIT DETAIL MESH®51 MM (2") MIN. AT BACKSIDEOF INSULATION BOARDDRYVIT DEMANDIT® OR COLOR PRIME™ON SURFACE(S) TO RECEIVE SEALANT


OSMD 0.0.23DRYVIT MD SPACERAPPROVED OSMD SYSTEM INSULATION BOARD


612


® ™

™

SUBSTRATE

DRYVIT MD SPACER


4RS 02/09

Inside / Outside Corners








DESIGNER SHALL DETERMINE THE NEED FOR ANEXPANSION JOINT AT CORNERS.


version.

DO NOT LAP REINFORCING MESH WITHIN 203 MM(8") OF A CORNER.

3.

4.


1.NOTE:

2. DOUBLE WRAP CORNERS WITH REINFORCINGMESH OR USE CORNER MESH.


MUST OVERLAP 203 MM (8") MIN.SEE ABOVE AND NOTES 2 AND 3

DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS, GENESIS DMOR GENESIS DMS BASE COAT




203 MM (8") MIN.(SEE NOTES 2 AND 3)


203 MM (8") MIN.(SEE NOTES 2 AND 3)

DRYVIT MD SPACERDRYVIT FINISH

OSMD 0.0.24


APPROVED OSMD SYSTEM INSULATION BOARDSUBSTRATE

™

™

® ™

4RS 02/09




version.without notice. Contact Dryvit to insure you have the most recent does not violate Dryvit's warranty. This detail is subject to change

LOCATE INSULATION BOARDS SUCH THATBOARD EDGES DO NOT ALIGN WITHCORNERS OF PENETRATION. standards. This detail is for general information and guidance only




APPLY A PIECE OF 241 MM (9 1/2") X 305 MM(12") DRYVIT REINFORCING MESH DIAGONALLYAT EACH CORNER.

2.

professional. All systems must comply with local building codes and Dryvit products is the responsibility of the project's design The architecture, engineering and design of the project using the 1.

NOTE:

DRYVIT DETAIL MESH241 MM (9 1/2") X 305 MM (12") (TYP.)

System Configuration At Openings

OFFSET INSULATION BOARDJOINTS FROM CORNERSOF OPENINGS


SPLICE PIECE OF DRYVIT DETAIL MESHREQUIRED AT CORNER


OSMD 0.0.25

® ™

CORROSION RESISTANT SCREW AND SLEEVE



RS

APPROVED BY:

®REV:

4

DATE:

02/09

version.



1. 2.NOTE:


of any project. The project design professional determines, in its sole discretion, whether this detail or a functionally equivalent alternative


Dryvit products is the responsibility of the project's design professional. All systems must comply with local building codes and


Shutter And Downspout Attachment

DRYVIT COMPATIBLE SEALANT,BY OTHERS

DOWNSPOUT STRAP

DRYVIT COMPATIBLE SEALANTBETWEEN SYSTEM AND STRAP,BY OTHERS

DOWNSPOUT


DRYVIT FINISH

CORROSION RESISTANT SCREWCORROSION RESISTANT SLEEVESHUTTER

OSMD 0.0.2612.7 MM (1/2") MIN.

SUBSTRATE


CODE APPROVED WATER-RESISTIVE BARRIERDRYVIT MD SPACER


® ™

™

Outsulation SMD SystemThe architecture, engineering and design of the project using the








®REV:

4RS

APPROVED BY: DATE:

02/09

version.

3. INSULATION BOARD THICKNESS MINUS THEDEPTH OF THE REVEAL SHALL NOT BE LESSTHAN 19 MM (3/4").

4.


1.NOTE:

2. BOTTOM EDGES OF ALL REVEALS MUST BESLOPED FOR DRAINAGE.


Aesthetic Reveals

OVERLAP 64 MM (2 1/2") MIN.

19 MM (3/4") MIN. (SEE NOTE 3)

REVEAL OPTIONS

DRYVIT FINISH


DRYVIT DETAIL MESH®241 MM (9 1/2") X 305 MM (12") (TYP.)DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COAT


SUBSTRATE

OSMD 0.0.27

DRYVIT MD SPACER


™

® ™

DRYVIT FINISH

NOTE:DRYVIT RECOMMENDS THAT GROUND FLOORAPPLICATIONS AND ALL FACADES EXPOSEDTO ABNORMAL STRESS, HIGH TRAFFIC, ORDELIBERATE IMPACT HAVE THE BASE COATREINFORCED WITH PANZER® MESH PRIORTO STANDARD MESH™ OR STANDARD PLUSMESH™. LOCATION OF HIGH IMPACT ZONESSHOULD BE INDICATED ON CONTRACTDRAWINGS.



4RS 02/09



of any project. The project design professional determines, in its sole discretion, whether this detail or a functionally equivalent alternative is best suited for the project. Use of a functionally equivalent detail



1. 2. Dryvit products is the responsibility of the project's design professional. All systems must comply with local building codes and standards. This detail is for general information and guidance only


Outsulation SMD System Minor Penetrations

DRYVIT MD SPACER


SUBSTRATE


CAULK PERIMETER OF PENETRATIONALONG SHEATHING.

12.7 MM (1/2") MIN.



DRYVIT DEMANDIT® OR COLOR PRIMEON SURFACE(S) TO RECEIVE SEALANT

WRAP DRYVIT DETAIL MESH® 51 MM (2") MIN. AT BACKSIDEOF INSULATION BOARD


OSMD 0.0.28

® ™

™

™

DRYVIT COMPATIBLE SEALANT,BY OTHERS


FLASHING NO. 1 EXTENDUP BEHIND FLASHINGNO. 2 76 MM (3") MIN.

NOTE:DRYVIT RECOMMENDS THAT GROUND FLOORAPPLICATIONS AND ALL FACADES EXPOSEDTO ABNORMAL STRESS, HIGH TRAFFIC, ORDELIBERATE IMPACT HAVE THE BASE COATREINFORCED WITH PANZER® MESH PRIORTO STANDARD MESH™ OR STANDARD PLUSMESH™. LOCATION OF HIGH IMPACT ZONESSHOULD BE INDICATED ON CONTRACTDRAWINGS.


APPROVED BY:

®REV: DATE:

4RS 02/09


1.





REFER TO OSMD DETAIL 0.0.30 FOR DECKCUTAWAY DETAIL.



The architecture, engineering and design of the project using the 2.


SUBSTRATE

Outsulation SMD System Wood Framed Deck - Cross Section

DRYVIT MD SPACER

DRAINAGE TRACK

DRYVIT FINISH

DECK FRAMINGFLASHING NO. 2 EXTEND UP BEHIND

FLASHING NO. 3 76 MM (3") MIN.

25 MM (1") MIN.

64 MM (2-1/2") MIN.

FLASHING NO. 3 EXTENDUP BEHIND INSULATION

BOARD 76 MM (3")

SUPPORT STRIP

DECK BOARDS51 MM (2") MIN.

OSMD 0.0.29APPROVED OSMD SYSTEMINSULATION BOARDCODE APPROVED WATER-RESISTIVE BARRIER


DRYVIT MD SPACER™LAPPED OVER FLANGE

OF DRAINAGE TRACK


® ™









Wood Framed Deck - Cut AwayNOTE:



4RS 02/09

version.

1. REFER TO OSMD DETAIL 0.0.29 FOR DECK-CROSS SECTION DETAIL.

2.


®

OSMD 0.0.30

DRAINAGE TRACK

OSMD SYSTEM

END JOIST

FLASHING NO. 3 TURNEDDOWN OVER END JOIST

WOOD DECK BOARD

FLASHING NO. 1

DRYVIT COMPATIBLESEALANT, BY OTHERS

FLASHING NO. 2 BEHINDAPPROVED OSMD BOARD

(HIDDEN)

® ™

NOTE:



4RS 02/09

version.without notice. Contact Dryvit to insure you have the most recent





1.



Outsulation SMD System Soffit Termination

SUBSTRATE

WOOD OR STEEL FRAMINGCODE APPROVED WATER-RESISTIVE BARRIER

DRYVIT MD SPACER

12.7 MM (1/2") MIN.DRYVIT DEMANDIT®OR COLOR PRIME™ON SURFACE(S) TO RECEIVE SEALANT


DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COATAPPROVED OSMD SYSTEM INSULATION BOARD

DRYVIT FINISH


DRYVIT COMPATIBLE SEALANT WITHCLOSED CELL BACKER ROD, BY OTHERS

OSMD 0.0.31

ROOF ASSEMBLY

® ™

™

SUBSTRATE


NOTE:


APPROVED BY:

®REV: DATE:

4RS 02/09


INSTALL SOFFIT FRIEZE BOARD AND TRIMAFTER OSMD SYSTEM IS IN PLACE.

1.




FOR NON-NAILABLE SHEATHING SUBSTRATES,THE FASTENERS MUST BE INSTALLED INTO THEFRAMING. standards. This detail is for general information and guidance only

professional. All systems must comply with local building codes and Dryvit products is the responsibility of the project's design The architecture, engineering and design of the project using the 2.


Outsulation SMD System Soffit With Frieze Board



12.7 MM (1/2") MIN.


SPACER BLOCK



38 MM (1-1/2") MIN.

DRYVIT COMPATIBLE SEALANT WITHBOND BREAKER, BY OTHERS

FRIEZE BOARD

OSMD 0.0.32

ROOF ASSEMBLY

® ™

™


GABLE END RAFTER

NOTE:










RS 4 02/09

version.

FOR RAKE WITH OVERHANG REFER TOOSMD DETAIL 0.0.32.

FOR NON-NAILABLE SHEATHING SUBSTRATES,THE FASTENER MUST BE INSTALLED INTO THEFRAMING.

1. 2.

®

Gable End With EIFS Trim




ROOF SHINGLES


64 MM (2-1/2") MIN.

DRYVIT COMPATIBLE SEALANTWITH BOND BREAKER, BY OTHERS

APPROVED OSMD SYSTEM INSULATION BOARD OR EPS TRIM (OPTIONAL)ADHERED WITH DRYVIT GENESIS,GENESIS DM OR GENESIS DMS BASECOAT OR MECHANICALLY FASTEN INTOSOLID SUBSTRATE

DRYVIT FINISH

DRIP EDGE FLASHING


SUBSTRATE

ROOFING PAPER

OSMD 0.0.33

SECTION A-A

® ™

™


WRAP DRYVIT DETAIL MESH®51 MM (2") MIN. AT BACKSIDE

OF INSULATION BOARD

DRYVIT COMPATIBLE SEALANTWITH CLOSED CELL BACKER ROD,

BY OTHERSDRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENER

NOTE:


DATE:

4RS 02/09

REV:APPROVED BY:

®

version.





FOR NON-NAILABLE SHEATHING SUBSTRATES,THE FASTENER MUST BE INSTALLED INTO THEFRAMING.

FOR RAKE WITH OVERHANG REFER TOOSMD DETAIL 0.0.32.

1. 2.professional. All systems must comply with local building codes and standards. This detail is for general information and guidance only



Outsulation SMD System Gable End With Wood Trim

DRYVIT FINISH

DRYVIT MD SPACERAPPROVED OSMD SYSTEM INSULATIONBOARD

ROOF SHINGLES

GABLE END RAFTERWOOD TRIM BOARD

38 MM (1 1/2") MIN.

DRYVIT DEMANDIT® OR COLOR PRIME™ ON SURFACE(S) TO RECEIVE SEALANT

SPACER BLOCK

SEALANT WITH BONDBREAKER, BY OTHERS 64 MM (2 1/2") MIN.


13 MM (1/2") MIN.

DRIP EDGE FLASHING

SUBSTRATE

ROOFING PAPER

OSMD 0.0.34

SECTION A-A

® ™

™

DRYVIT MD SPACER LAPPED OVERFLANGE OF DRAINAGE TRACK


NOTE:


4RS 02/09


®

version.


1.


discretion, whether this detail or a functionally equivalent alternative is best suited for the project. Use of a functionally equivalent detail does not violate Dryvit's warranty. This detail is subject to change


APPROVED OSMD INSULATION BOARD MAY NEEDTO BE NOTCHED TO ACCOMMODATEWATER-RESISTIVE BARRIER/ DRAINAGE MEDIUM.

professional. All systems must comply with local building codes and standards. This detail is for general information and guidance only and Dryvit specifically disclaims any liability for the use of

2. Dryvit products is the responsibility of the project's design The architecture, engineering and design of the project using the

Outsulation SMD System Termination at Parapet

DRAINAGE TRACK



ROOF ASSEMBLY

203 MM (8") MIN.

DRYVIT MD SPACERDrainage TrackOption


SUBSTRATE

ROOF FLASHING ANDCOUNTERFLASHING

WOOD OR STEEL FRAMINGAPPROVED OSMD SYSTEMINSULATION BOARD

DRYVIT FINISH


OSMD 0.0.35



64 MM (2 1/2") MIN.

METAL CAP FLASHING

® ™

™

FASCIADRIP EDGE

SOLDER ALL JOINTSIN KICKOUT DIVERTER

Termination at Roof to Wall Flashing








The architecture, engineering and design of the project using the NOTE:

EXTEND ROOFING PAPER 127 MM (5") MIN.UP VERTICAL WALL BEHIND METALFLASHING.

4RS 02/09


version.

METAL FLASHINGS ARE 254 MM (10") X 51 MM(2") LONGER THAN THE EXPOSED PORTION OFTHE ROOFING SHINGLE AND ARE BENT IN HALFTO ALLOW FOR TWO 127 MM (5") LEGS.ALTHOUGH NOT SHOWN, METAL FLASHINGS ARESTEP FLASHED (INTERWOVEN) WITH ROOFINGSHINGLES.

KICKOUT DIVERTER TO BE MADE FROMCORROSION RESISTANT MATERIAL MIN. 24GAGE.

3.

EXTEND KICKOUT A MINIMUM OF 25 MM (1")BEYOND FACE OF SYSTEM.

2.

1. 4.


®

DRYVIT MD SPACER 152 MM(6")

CODE APPROVED WATER-RESISTIVEBARRIER LAPPED OVER FLASHING

ROOF SHINGLESROOFING PAPER(SEE NOTE 3)

METAL FLASHING, BY OTHERS(SEE NOTE 4)



50MM (2") MIN.

KICKOUT DIVERTER

OSMD 0.0.36

152 MM(6")

110

100

303 MM(12")

® ™

™

REFER TO DETAILS OSMD 0.0.01,0.0.02 AND 0.0.03 FOR SYSTEMCONFIGURATION OPTIONS.

1. The architecture, engineering and design of the project using the


DATE:

02/094RS

REV:APPROVED BY:

®

version.



of any project. The project design professional determines, in its sole discretion, whether this detail or a functionally equivalent alternative

professional. All systems must comply with local building codes and standards. This detail is for general information and guidance only and Dryvit specifically disclaims any liability for the use of


Outsulation SMD SystemNOTE:

Chimney Enclosure

CRICKET FLASHING

CODE APPROVED WATER-RESISTIVEBARRIER OVER SUBSTRATE

STEP FLASH ROOFING SHINGLESAND METAL FLASHING

DIVERTER FLASHING(SEE DETAIL OSMD 0.0.36)


50 MM (2") MIN. CLEARANCEBETWEEN OSMD

SYSTEM AND SHINGLES DRAINAGE STRIP

ROOFING SHINGLES

SEAL BETWEEN METAL CAP ANDDRYVIT SYSTEM USING DRYVIT

COMPATIBLE SEALANT WITHBOND BREAKER, BY OTHERS

SUBSTRATE

OSMD SYSTEM

TERMINAL RAIN CAP

OSMD 0.0.37

® ™

outsulation smd system installation details (formerly ... · outsulation smd system installation...

Documents