q-lon – innovative weatherseals for timber windows and doors
TRANSCRIPT
Stan
d 04
/12
®
SCHLEGEL GERMANY GMBH ·Bredowstr.33·22113Hamburg·Tel.+49(40)73329-0·Fax73329-219·www.schlegel.com
a member of
Q-LON – innovative weatherseals for timber windows and doors
tested
®
Tests and results
Compression set: < 15% after 1 hour relief of 50% compression at 70 °C and24hours.(DIN53572)
Compression force: approx. 15 N at 25% compression per 100 mm, < 10 N for lip profiles
Tested temperature range: - 60 °C to + 70 °C
Long life performance: no change of the length-related and partial joint permeability
Environmenttesting: TestedandpassedpursuanttoDIN18055,EN12207andEN12208to600PaatsingleandFrenchwindow
Paint compatibility: No adhesion, no hardening, no discolouration
Acoustingtesting: 43dB*)or45dB**)measuredatawindowIV68withsashrebateseal*)orawindowIV76withasashrebatesealandsecondsashsealing**)
Weather-resistant: tested up to 21 years
A stationary test stand according to the Rosenheim guidelines is part of the service programme of SCHLEGEL. Here, the SCHLEGEL seals are carefully verified for function and quality.
This test stand is also available to all of our customers and potential customers for inspections. SCHLEGEL supports the development work of its customers this way.
Heat conductivity: 0.033 W / mK at 0 °С
SCHLEGEL GERMANY GMBH·Bredowstr.33·D-22113HamburgTel.+49(40)73329-0·Fax+49(40)73329-219·E-Mail:[email protected]
www.schlegel.de · www.schlegel.com
Q-LON: Easy and quick installation
Installation of Q-LON in the sash
1. The Q-LON profile is pressed into the kerf at the centre of the sash.
2. The Q-LON pliers are placed in the rebate corner with the stop and a 90° mitre is cut out.
3. The final cut: By positioning the pliers against the profile as shown, the final cut is made in the precise length.
Tools and accessories for rational processing
Q-LON-pliers with insertion roll for 90° and end cut for assembly in the sash Partno.MIS-9001-97
Profile manual rollerPartno.MIS-9007-01
Dispenserfor2Q-LONcoilsPartno.MIS-9000-F17.1
Special profiles for French windowsQ-LON overlapping cover caps (figure on the left) and weather seals DX 1362 (figure on the right).
WeathersealDX1362ofacrylicpaint-compatibleTPE*, for 4-5 mm groove and 12, 18-20 mm rebate width.
CovercapsofresistantHDPE*,for3,4and5mmgrooveandfor 10, 12, and 18-20 mm rebate width. Also available for QL3034/3070 and QL3054.*in the colours of the Q-LON profiles
Q-LON
The sealing specialistsWith decades of experience and the comprehensive programme for use in windows and doors made of wood, plasticandaluminium•Furnitureandinteriordesign•Rollershutters•Innewconstructionandforrenovations
Profile selection guide for windows and frames Profile selection guide for doors and special profiles
Sealings for window sash
Sealings for window sash
QL-3053 QL-3062 QL-3064 QL-3067 QL-3111 QL-3123
K: 4–5 x 8 mm R: 12 mmS: 5 mm
K: 4–5 x 8 mm R: 12 mmS: 6 mm
K: 4–5 x 8 mm R: 12 mmS: 5 mm
K: 4–5 x 8 mm R: 12 mmS: 5 mm
K: 4,5–5 x 8 mm R: 12 mmS: 5 mm
K: 4–5 x 8 mm R: 12 mmS: 5 mm
K: kerf / R: rebate / S: seal gap
Sealings for frames
Sealings for frames
QL-3013
K: 3 x 6 mm R: min. 8 mmS: 2–3 mm
QL-3004
K: 3 x 7 mm R: 10 mmS: 4 mm
QL-3005
K: 3 x 6 mm R: min. 8 mmS: 4 mm
QL-3078
K: 3 x 7 mm R: 10–11 mmS: 4 mm
QL-3118 QL-3006
K: 3 x 7 mm R: 9 mmS: 4 mm
K: 3 mm R: 13 mmS: 5-13 mm
QL-3011
K: 3 x 7 mm R: 10 mmS: 4 mm
QL-3037
K: 3 x 7 mm R: 10 mmS: 4 mm
QL-3012
K: 3 x 7 mm R: 11 mmS: 5 mm
7,5
12 12
9,0 7,5
12
7,5
12
QL-3068
K: 4 x 8 mm R: 11–12 mmS: 5 mm
8,0
11
QL-3072/79
K: 3/4 x 7 mm R: 10 mmS: 3 mm
5
10
Sealings for doorsQL-3109 QL-3091 QL-3098 QL-3120
K: 5 x 7 mm R: 18 mmS: 5–8 mm
4–5 x 7 mm 15 mm 5 mm
4 x 7 mm 14 mm 3–6 mm
K: 4 mm R: 12 mmS: 5-7 mm
11
15
9,8 8
14
7,8
3,7 6
10,5
6,5
6,8
9
10,5
11
6,5
11
6,5
8
10,5
Ventilation brushDX-1316
K: 4–5 x 8 mm R: 12 mmS: 5 mm
00
6,0
12
Special profiles for stapling on self-adhesive
QL-3042 QL-3059 QL-3061 QL-3015 QL-3115 QL-3122 QL-3124 QL-3126
K: – R: 11 mmS: 3 mm
K: – R: 11 mmS: 3 mm
K: – R: 15 mmS: 7 mm
K: – R: min. 8 mmS: 3 mm
11
6,5
11
9
15
12
8
5
Sealings for internal doorsQL-3106 QL-3110 QL-50/QL-9827
K: 4 x 7 mm R: 12 mmS: 5 mm
K: 4 x 7 mmR: 12 mmS: 5 mm
K: 3 mmR: 10 mmS: 3 mm
12
6 6
12
The material components of the Q-LON seals in combination lead to technical values that are not achieved by any other ma-terials used in seals. The extremely low K-value of 0.033 is better by a factor of 10 than that of any solid material, supporting the objective of energy-saving elements. Long-term research, continuous further development and strict material controlls have made Q-LON one of the best-established sealing systems around the world.Assembly easy and quick. By cutting out the seal in the mitre corners, the extensive welding on of the profile corners can be dispensed with.Q-LON has proven well in more than 30 years of use. More than 100 M windows and doors have been equipped with Q-LON seals since then.
Q-LON profiles bring true benefits for you!• efficient processing - right from the coil, no waste• easyandquickassemblybycutting-outofthemitrecorners• greatrecovery• compatiblewithallpaintsandglazes,includingAcrylicpaints• cleaning-agentresistant• highelasticundercold,longlifetime• sound-insulatingprofile• availableinthecolours:brown,white,black,grey,beige,oak
light and chestnut, other colours available on request• oncoilsàapprox.100-500m.(profile-dependent),
2 coils per carton
Polyethylene film - smooth, contamination-resistant surface
Polyurethane foam profile core - highly elastic, very good recovery, great heat/cold performance
Polypropylene profile insert - no elongation, no shrinkage
TPE flipper - easy assembly, firm fit in the kerf
Q-LON – tested – proofed – durable
PE
PU
PP
TPESealings for French windows
Q-LON Cover cap DX-1362
K: 4 + 5 mm R: 12 + 18–20 mmS: –
K: 4–5 mmR: 12 + 18–20 mmS: –
Q-LON
2nd sash sealingsQL-3097
K: 4– 4,5 x 7 mm R: 18 mmS: 4 mm
QL-3034
K: 3 x 8 mm R: –S: –
QL-3070 QL-3129
K: 3 x 5 mm R: –S: –
K: 3 x 5 mm R: –S: –
QL-3054/80
K: 3/4 x 5 mm R: 10 mmS: 6 mm
18
7,2
5
8,9
4,5
7,8
7,5
10
Q-LON-profiles - tested with very good results
MPANW
Centre sash & optional/ required 2nd seal
QL-3130 QL-3136
K: 3 mm R: 11/12 mmS: 5/6 mm
K: 3 mm R: 11/12 mmS: 5/6 mm
8
11,5
7,0
4,2
11,1
17,3
QL-3093 QL-3104 QL-3096 QL-3094/95
K: 3 x 7 mm R: 13 mmS: 4–5 mm
K: 4–5 x 7 mm R: 12 mmS: 5–6 mm
K: 4–5 x 7 mm R: 12 mmS: 3–6 mm
K: 3/4 x 5 mm R: 10 mmS: 3–4 mm
9,5
13 12
11 8
12
8
10
10
10,4
Special profiles self-adhesive
QL-3116 QL-3117 QL-3121
QL-3025
K: 3 x 7 mm R: 10 mmS: 4 mm
6
10,5
QL-3009
K: 3 x 7 mm R: 11 mmS: 5 mm
9
10,5
QL-3056
K: 3 x 7 mm R: 11 mmS: 5 mm
9
10,5
QL-3099
K: 3 x 7 mm R: 10–11 mmS: 4 mm
9
10,5
QL-3133
K: 3 mm R: 7 mmS: 4-6 mm
9
12,1
QL-3100developement
K: 4 x 7 mm R: 12 mmS: 5–7 mm
12
8,8
QL-3113developement
K: 4 x 7 mmR: 12 mmS: 5 mm
12,5
8,5
QL-3137 developement
K: 3 mmR: 8 mmS: 4 mm
QL-3138developement
K: 3 mmR: 10 mmS: 4 mm
K: – R: 7 mmS: –
K: – R: 7 mmS: –
K: – R: 6 mmS: –
K: – R: 10 mmS: –
K: – R: 11 mmS: 3 mm
K: – R: 11 mmS: 3 mm
K: – R: 15 mmS: 7 mm
18
Profile selection guide for windows and frames Profile selection guide for doors and special profiles
Sealings for window sash
Sealings for window sash
QL-3053 QL-3062 QL-3064 QL-3067 QL-3111 QL-3123
K: 4–5 x 8 mm R: 12 mmS: 5 mm
K: 4–5 x 8 mm R: 12 mmS: 6 mm
K: 4–5 x 8 mm R: 12 mmS: 5 mm
K: 4–5 x 8 mm R: 12 mmS: 5 mm
K: 4,5–5 x 8 mm R: 12 mmS: 5 mm
K: 4–5 x 8 mm R: 12 mmS: 5 mm
K: kerf / R: rebate / S: seal gap
Sealings for frames
Sealings for frames
QL-3013
K: 3 x 6 mm R: min. 8 mmS: 2–3 mm
QL-3004
K: 3 x 7 mm R: 10 mmS: 4 mm
QL-3005
K: 3 x 6 mm R: min. 8 mmS: 4 mm
QL-3078
K: 3 x 7 mm R: 10–11 mmS: 4 mm
QL-3118 QL-3006
K: 3 x 7 mm R: 9 mmS: 4 mm
K: 3 mm R: 13 mmS: 5-13 mm
QL-3011
K: 3 x 7 mm R: 10 mmS: 4 mm
QL-3037
K: 3 x 7 mm R: 10 mmS: 4 mm
QL-3012
K: 3 x 7 mm R: 11 mmS: 5 mm
7,5
12 12
9,0 7,5
12
7,5
12
QL-3068
K: 4 x 8 mm R: 11–12 mmS: 5 mm
8,0
11
QL-3072/79
K: 3/4 x 7 mm R: 10 mmS: 3 mm
5
10
Sealings for doorsQL-3109 QL-3091 QL-3098 QL-3120
K: 5 x 7 mm R: 18 mmS: 5–8 mm
4–5 x 7 mm 15 mm 5 mm
4 x 7 mm 14 mm 3–6 mm
K: 4 mm R: 12 mmS: 5-7 mm
11
15
9,8 8
14
7,8
3,7 6
10,5
6,5
6,8
9
10,5
11
6,5
11
6,5
8
10,5
Ventilation brushDX-1316
K: 4–5 x 8 mm R: 12 mmS: 5 mm
00
6,0
12
Special profiles for stapling on self-adhesive
QL-3042 QL-3059 QL-3061 QL-3015 QL-3115 QL-3122 QL-3124 QL-3126
K: – R: 11 mmS: 3 mm
K: – R: 11 mmS: 3 mm
K: – R: 15 mmS: 7 mm
K: – R: min. 8 mmS: 3 mm
11
6,5
11
9
15
12
8
5
Sealings for internal doorsQL-3106 QL-3110 QL-50/QL-9827
K: 4 x 7 mm R: 12 mmS: 5 mm
K: 4 x 7 mmR: 12 mmS: 5 mm
K: 3 mmR: 10 mmS: 3 mm
12
6 6
12
The material components of the Q-LON seals in combination lead to technical values that are not achieved by any other ma-terials used in seals. The extremely low K-value of 0.033 is better by a factor of 10 than that of any solid material, supporting the objective of energy-saving elements. Long-term research, continuous further development and strict material controlls have made Q-LON one of the best-established sealing systems around the world.Assembly easy and quick. By cutting out the seal in the mitre corners, the extensive welding on of the profile corners can be dispensed with.Q-LON has proven well in more than 30 years of use. More than 100 M windows and doors have been equipped with Q-LON seals since then.
Q-LON profiles bring true benefits for you!• efficient processing - right from the coil, no waste• easyandquickassemblybycutting-outofthemitrecorners• greatrecovery• compatiblewithallpaintsandglazes,includingAcrylicpaints• cleaning-agentresistant• highelasticundercold,longlifetime• sound-insulatingprofile• availableinthecolours:brown,white,black,grey,beige,oak
light and chestnut, other colours available on request• oncoilsàapprox.100-500m.(profile-dependent),
2 coils per carton
Polyethylene film - smooth, contamination-resistant surface
Polyurethane foam profile core - highly elastic, very good recovery, great heat/cold performance
Polypropylene profile insert - no elongation, no shrinkage
TPE flipper - easy assembly, firm fit in the kerf
Q-LON – tested – proofed – durable
PE
PU
PP
TPESealings for French windows
Q-LON Cover cap DX-1362
K: 4 + 5 mm R: 12 + 18–20 mmS: –
K: 4–5 mmR: 12 + 18–20 mmS: –
Q-LON
2nd sash sealingsQL-3097
K: 4– 4,5 x 7 mm R: 18 mmS: 4 mm
QL-3034
K: 3 x 8 mm R: –S: –
QL-3070 QL-3129
K: 3 x 5 mm R: –S: –
K: 3 x 5 mm R: –S: –
QL-3054/80
K: 3/4 x 5 mm R: 10 mmS: 6 mm
18
7,2
5
8,9
4,5
7,8
7,5
10
Q-LON-profiles - tested with very good results
MPANW
Centre sash & optional/ required 2nd seal
QL-3130 QL-3136
K: 3 mm R: 11/12 mmS: 5/6 mm
K: 3 mm R: 11/12 mmS: 5/6 mm
8
11,5
7,0
4,2
11,1
17,3
QL-3093 QL-3104 QL-3096 QL-3094/95
K: 3 x 7 mm R: 13 mmS: 4–5 mm
K: 4–5 x 7 mm R: 12 mmS: 5–6 mm
K: 4–5 x 7 mm R: 12 mmS: 3–6 mm
K: 3/4 x 5 mm R: 10 mmS: 3–4 mm
9,5
13 12
11 8
12
8
10
10
10,4
Special profiles self-adhesive
QL-3116 QL-3117 QL-3121
QL-3025
K: 3 x 7 mm R: 10 mmS: 4 mm
6
10,5
QL-3009
K: 3 x 7 mm R: 11 mmS: 5 mm
9
10,5
QL-3056
K: 3 x 7 mm R: 11 mmS: 5 mm
9
10,5
QL-3099
K: 3 x 7 mm R: 10–11 mmS: 4 mm
9
10,5
QL-3133
K: 3 mm R: 7 mmS: 4-6 mm
9
12,1
QL-3100developement
K: 4 x 7 mm R: 12 mmS: 5–7 mm
12
8,8
QL-3113developement
K: 4 x 7 mmR: 12 mmS: 5 mm
12,5
8,5
QL-3137 developement
K: 3 mmR: 8 mmS: 4 mm
QL-3138developement
K: 3 mmR: 10 mmS: 4 mm
K: – R: 7 mmS: –
K: – R: 7 mmS: –
K: – R: 6 mmS: –
K: – R: 10 mmS: –
K: – R: 11 mmS: 3 mm
K: – R: 11 mmS: 3 mm
K: – R: 15 mmS: 7 mm
18
Profile selection guide for windows and frames Profile selection guide for doors and special profiles
Sealings for window sash
Sealings for window sash
QL-3053 QL-3062 QL-3064 QL-3067 QL-3111 QL-3123
K: 4–5 x 8 mm R: 12 mmS: 5 mm
K: 4–5 x 8 mm R: 12 mmS: 6 mm
K: 4–5 x 8 mm R: 12 mmS: 5 mm
K: 4–5 x 8 mm R: 12 mmS: 5 mm
K: 4,5–5 x 8 mm R: 12 mmS: 5 mm
K: 4–5 x 8 mm R: 12 mmS: 5 mm
K: kerf / R: rebate / S: seal gap
Sealings for frames
Sealings for frames
QL-3013
K: 3 x 6 mm R: min. 8 mmS: 2–3 mm
QL-3004
K: 3 x 7 mm R: 10 mmS: 4 mm
QL-3005
K: 3 x 6 mm R: min. 8 mmS: 4 mm
QL-3078
K: 3 x 7 mm R: 10–11 mmS: 4 mm
QL-3118 QL-3006
K: 3 x 7 mm R: 9 mmS: 4 mm
K: 3 mm R: 13 mmS: 5-13 mm
QL-3011
K: 3 x 7 mm R: 10 mmS: 4 mm
QL-3037
K: 3 x 7 mm R: 10 mmS: 4 mm
QL-3012
K: 3 x 7 mm R: 11 mmS: 5 mm
7,5
12 12
9,0 7,5
12
7,5
12
QL-3068
K: 4 x 8 mm R: 11–12 mmS: 5 mm
8,0
11
QL-3072/79
K: 3/4 x 7 mm R: 10 mmS: 3 mm
5
10
Sealings for doorsQL-3109 QL-3091 QL-3098 QL-3120
K: 5 x 7 mm R: 18 mmS: 5–8 mm
4–5 x 7 mm 15 mm 5 mm
4 x 7 mm 14 mm 3–6 mm
K: 4 mm R: 12 mmS: 5-7 mm
11
15
9,8 8
14
7,8
3,7 6
10,5
6,5
6,8
9
10,5
11
6,5
11
6,5
8
10,5
Ventilation brushDX-1316
K: 4–5 x 8 mm R: 12 mmS: 5 mm
00
6,0
12
Special profiles for stapling on self-adhesive
QL-3042 QL-3059 QL-3061 QL-3015 QL-3115 QL-3122 QL-3124 QL-3126
K: – R: 11 mmS: 3 mm
K: – R: 11 mmS: 3 mm
K: – R: 15 mmS: 7 mm
K: – R: min. 8 mmS: 3 mm
11
6,5
11
9
15
12
8
5
Sealings for internal doorsQL-3106 QL-3110 QL-50/QL-9827
K: 4 x 7 mm R: 12 mmS: 5 mm
K: 4 x 7 mmR: 12 mmS: 5 mm
K: 3 mmR: 10 mmS: 3 mm
12
6 6
12
The material components of the Q-LON seals in combination lead to technical values that are not achieved by any other ma-terials used in seals. The extremely low K-value of 0.033 is better by a factor of 10 than that of any solid material, supporting the objective of energy-saving elements. Long-term research, continuous further development and strict material controlls have made Q-LON one of the best-established sealing systems around the world.Assembly easy and quick. By cutting out the seal in the mitre corners, the extensive welding on of the profile corners can be dispensed with.Q-LON has proven well in more than 30 years of use. More than 100 M windows and doors have been equipped with Q-LON seals since then.
Q-LON profiles bring true benefits for you!• efficient processing - right from the coil, no waste• easyandquickassemblybycutting-outofthemitrecorners• greatrecovery• compatiblewithallpaintsandglazes,includingAcrylicpaints• cleaning-agentresistant• highelasticundercold,longlifetime• sound-insulatingprofile• availableinthecolours:brown,white,black,grey,beige,oak
light and chestnut, other colours available on request• oncoilsàapprox.100-500m.(profile-dependent),
2 coils per carton
Polyethylene film - smooth, contamination-resistant surface
Polyurethane foam profile core - highly elastic, very good recovery, great heat/cold performance
Polypropylene profile insert - no elongation, no shrinkage
TPE flipper - easy assembly, firm fit in the kerf
Q-LON – tested – proofed – durable
PE
PU
PP
TPESealings for French windows
Q-LON Cover cap DX-1362
K: 4 + 5 mm R: 12 + 18–20 mmS: –
K: 4–5 mmR: 12 + 18–20 mmS: –
Q-LON
2nd sash sealingsQL-3097
K: 4– 4,5 x 7 mm R: 18 mmS: 4 mm
QL-3034
K: 3 x 8 mm R: –S: –
QL-3070 QL-3129
K: 3 x 5 mm R: –S: –
K: 3 x 5 mm R: –S: –
QL-3054/80
K: 3/4 x 5 mm R: 10 mmS: 6 mm
18
7,2
5
8,9
4,5
7,8
7,5
10
Q-LON-profiles - tested with very good results
MPANW
Centre sash & optional/ required 2nd seal
QL-3130 QL-3136
K: 3 mm R: 11/12 mmS: 5/6 mm
K: 3 mm R: 11/12 mmS: 5/6 mm
8
11,5
7,0
4,2
11,1
17,3
QL-3093 QL-3104 QL-3096 QL-3094/95
K: 3 x 7 mm R: 13 mmS: 4–5 mm
K: 4–5 x 7 mm R: 12 mmS: 5–6 mm
K: 4–5 x 7 mm R: 12 mmS: 3–6 mm
K: 3/4 x 5 mm R: 10 mmS: 3–4 mm
9,5
13 12
11 8
12
8
10
10
10,4
Special profiles self-adhesive
QL-3116 QL-3117 QL-3121
QL-3025
K: 3 x 7 mm R: 10 mmS: 4 mm
6
10,5
QL-3009
K: 3 x 7 mm R: 11 mmS: 5 mm
9
10,5
QL-3056
K: 3 x 7 mm R: 11 mmS: 5 mm
9
10,5
QL-3099
K: 3 x 7 mm R: 10–11 mmS: 4 mm
9
10,5
QL-3133
K: 3 mm R: 7 mmS: 4-6 mm
9
12,1
QL-3100developement
K: 4 x 7 mm R: 12 mmS: 5–7 mm
12
8,8
QL-3113developement
K: 4 x 7 mmR: 12 mmS: 5 mm
12,5
8,5
QL-3137 developement
K: 3 mmR: 8 mmS: 4 mm
QL-3138developement
K: 3 mmR: 10 mmS: 4 mm
K: – R: 7 mmS: –
K: – R: 7 mmS: –
K: – R: 6 mmS: –
K: – R: 10 mmS: –
K: – R: 11 mmS: 3 mm
K: – R: 11 mmS: 3 mm
K: – R: 15 mmS: 7 mm
18
Stan
d 04
/12
®
SCHLEGEL GERMANY GMBH ·Bredowstr.33·22113Hamburg·Tel.+49(40)73329-0·Fax73329-219·www.schlegel.com
a member of
Q-LON – innovative weatherseals for timber windows and doors
tested
®
Tests and results
Compression set: < 15% after 1 hour relief of 50% compression at 70 °C and24hours.(DIN53572)
Compression force: approx. 15 N at 25% compression per 100 mm, < 10 N for lip profiles
Tested temperature range: - 60 °C to + 70 °C
Long life performance: no change of the length-related and partial joint permeability
Environmenttesting: TestedandpassedpursuanttoDIN18055,EN12207andEN12208to600PaatsingleandFrenchwindow
Paint compatibility: No adhesion, no hardening, no discolouration
Acoustingtesting: 43dB*)or45dB**)measuredatawindowIV68withsashrebateseal*)orawindowIV76withasashrebatesealandsecondsashsealing**)
Weather-resistant: tested up to 21 years
A stationary test stand according to the Rosenheim guidelines is part of the service programme of SCHLEGEL. Here, the SCHLEGEL seals are carefully verified for function and quality.
This test stand is also available to all of our customers and potential customers for inspections. SCHLEGEL supports the development work of its customers this way.
Heat conductivity: 0.033 W / mK at 0 °С
SCHLEGEL GERMANY GMBH·Bredowstr.33·D-22113HamburgTel.+49(40)73329-0·Fax+49(40)73329-219·E-Mail:[email protected]
www.schlegel.de · www.schlegel.com
Q-LON: Easy and quick installation
Installation of Q-LON in the sash
1. The Q-LON profile is pressed into the kerf at the centre of the sash.
2. The Q-LON pliers are placed in the rebate corner with the stop and a 90° mitre is cut out.
3. The final cut: By positioning the pliers against the profile as shown, the final cut is made in the precise length.
Tools and accessories for rational processing
Q-LON-pliers with insertion roll for 90° and end cut for assembly in the sash Partno.MIS-9001-97
Profile manual rollerPartno.MIS-9007-01
Dispenserfor2Q-LONcoilsPartno.MIS-9000-F17.1
Special profiles for French windowsQ-LON overlapping cover caps (figure on the left) and weather seals DX 1362 (figure on the right).
WeathersealDX1362ofacrylicpaint-compatibleTPE*, for 4-5 mm groove and 12, 18-20 mm rebate width.
CovercapsofresistantHDPE*,for3,4and5mmgrooveandfor 10, 12, and 18-20 mm rebate width. Also available for QL3034/3070 and QL3054.*in the colours of the Q-LON profiles
Q-LON
The sealing specialistsWith decades of experience and the comprehensive programme for use in windows and doors made of wood, plasticandaluminium•Furnitureandinteriordesign•Rollershutters•Innewconstructionandforrenovations
Stan
d 04
/12
®
SCHLEGEL GERMANY GMBH ·Bredowstr.33·22113Hamburg·Tel.+49(40)73329-0·Fax73329-219·www.schlegel.com
a member of
Q-LON – innovative weatherseals for timber windows and doors
tested
®
Tests and results
Compression set: < 15% after 1 hour relief of 50% compression at 70 °C and24hours.(DIN53572)
Compression force: approx. 15 N at 25% compression per 100 mm, < 10 N for lip profiles
Tested temperature range: - 60 °C to + 70 °C
Long life performance: no change of the length-related and partial joint permeability
Environmenttesting: TestedandpassedpursuanttoDIN18055,EN12207andEN12208to600PaatsingleandFrenchwindow
Paint compatibility: No adhesion, no hardening, no discolouration
Acoustingtesting: 43dB*)or45dB**)measuredatawindowIV68withsashrebateseal*)orawindowIV76withasashrebatesealandsecondsashsealing**)
Weather-resistant: tested up to 21 years
A stationary test stand according to the Rosenheim guidelines is part of the service programme of SCHLEGEL. Here, the SCHLEGEL seals are carefully verified for function and quality.
This test stand is also available to all of our customers and potential customers for inspections. SCHLEGEL supports the development work of its customers this way.
Heat conductivity: 0.033 W / mK at 0 °С
SCHLEGEL GERMANY GMBH·Bredowstr.33·D-22113HamburgTel.+49(40)73329-0·Fax+49(40)73329-219·E-Mail:[email protected]
www.schlegel.de · www.schlegel.com
Q-LON: Easy and quick installation
Installation of Q-LON in the sash
1. The Q-LON profile is pressed into the kerf at the centre of the sash.
2. The Q-LON pliers are placed in the rebate corner with the stop and a 90° mitre is cut out.
3. The final cut: By positioning the pliers against the profile as shown, the final cut is made in the precise length.
Tools and accessories for rational processing
Q-LON-pliers with insertion roll for 90° and end cut for assembly in the sash Partno.MIS-9001-97
Profile manual rollerPartno.MIS-9007-01
Dispenserfor2Q-LONcoilsPartno.MIS-9000-F17.1
Special profiles for French windowsQ-LON overlapping cover caps (figure on the left) and weather seals DX 1362 (figure on the right).
WeathersealDX1362ofacrylicpaint-compatibleTPE*, for 4-5 mm groove and 12, 18-20 mm rebate width.
CovercapsofresistantHDPE*,for3,4and5mmgrooveandfor 10, 12, and 18-20 mm rebate width. Also available for QL3034/3070 and QL3054.*in the colours of the Q-LON profiles
Q-LON
The sealing specialistsWith decades of experience and the comprehensive programme for use in windows and doors made of wood, plasticandaluminium•Furnitureandinteriordesign•Rollershutters•Innewconstructionandforrenovations