test report - faenl.msi.comfaenl.msi.com/ftp/ce documents/notebook/ms-16y1 (cx640,cr640... · the...

Test Report

Product Name ： Notebook PC

Model No. ： MS-16Y1

Applicant ： PEGATRON CORPORATION

Address ： 5F,No.76,Ligong St.,Beitou,Taipei 112,Taiwan

Date of Receipt ： 2010/12/20

Issued Date ： 2011/01/12

Report No. ： 10C319R-ITCEP07V04

Report Version : V1.0

The test results relate only to the samples tested.

The test results shown in the test report are traceable to the national/international standard through the calibration of the equipment and evaluated measurement uncertainty herein.

This report must not be used to claim product endorsement by TAF, NVLAP or any agency of the Government.

The test report shall not be reproduced except in full without the written approval of QuieTek Corporation.

Report No：10C319R-ITCEP07V04

Page: 2 of 217

Test Report Cert i f icat ion Issued Date : 2011/01/12 Report No. : 10C319R-ITCEP07V04

Product Name : Notebook PC

Applicant : PEGATRON CORPORATION

Address : 5F,No.76, Ligong St., Beitou,Taipei 112,Taiwan

Manufacturer : 1.PEGATRON CORPORATION Taoyuan Mfg

2.Protek (Shanghai) Limited.

3.MAINTEK COMPUTER(SUZHOU) CO., LTD.

Model No. : MS-16Y1

EUT Rated Voltage : AC 100-240V, 50-60Hz

EUT Test Voltage : AC 230 V / 50 Hz

Trade Name : msi

Applicable Standard : EN 55022:2006+A1: 2007, Class B

EN 55024: 1998+A1: 2001+A2: 2003

EN 61000-3-2: 2006+A2: 2009

EN 61000-3-3: 2008

Test Result : Complied

Performed Location : Quietek Corporation (Linkou Laboratory)

No. 5-22, Rueishu Keng, Linkou Dist., New Taipei City

24451, Taiwan. R.O.C.

TEL:+866-2-8601-3788 / FAX:+886-2-8601-3789

Documented By :

(Adm.Assistant / Anny Chou)

Reviewed By :

( Assistant Engineer / Tim Ho )

Approved By :

( Manager / Vincent Lin )


Page: 3 of 217

Laboratory Information We, QuieTek Corporation, are an independent EMC and safety consultancy that was established the whole facility in our laboratories. The test facility has been accredited/accepted (audited or listed) by the following related bodies in compliance with ISO 17025, EN 45001 and specified testing scopes:

The related certificate for our laboratories about the test site and management system can be downloaded from QuieTek Corporation’s Web Site : http://www.quietek.com/tw/ctg/cts/accreditations.htm The address and introduction of QuieTek Corporation’s laboratories can be founded in our Web site : http://www.quietek.com/ If you have any comments, Please don’t hesitate to contact us. Our contact information is as below: HsinChu Testing Laboratory :

No.75-2, 3rd Lin, Wangye Keng, Yonghxing Tsuen, Qionglin Shiang, Hsinchu County 307, Taiwan, R.O.C. TEL:+886-3-592-8858 / FAX:+886-3-592-8859 E-Mail : [email protected]

LinKou Testing Laboratory :

No. 5-22, Rueishu Keng, Linkou Dist., New Taipei City 24451, Taiwan. R.O.C. TEL : 886-2-8601-3788 / FAX : 886-2-8601-3789 E-Mail : [email protected]

Suzhou (China) Testing Laboratory :

No. 99 Hongye Rd., Suzhou Industrial Park Loufeng Hi-Tech Development Zone., Suzhou,China.TEL : +86-512-6251-5088 / FAX : +86-512-6251-5098 E-Mail : [email protected]

Taiwan R.O.C. : BSMI, NCC, TAF

Germany : TUV Rheinland

Norway : Nemko, DNV

USA : FCC, NVLAP

Japan : VCCI


Page: 4 of 217

TABLE OF CONTENTS Description Page 1. General Information .................................................................................................... 7

1.1. EUT Description................................................................................................... 7

1.2. Mode of Operation............................................................................................. 10

1.3. Tested System Details ....................................................................................... 12

1.4. Configuration of Tested System......................................................................... 13

1.5. EUT Exercise Software...................................................................................... 15

2. Technical Test ........................................................................................................... 16

2.1. Summary of Test Result..................................................................................... 16

2.2. List of Test Equipment ....................................................................................... 17

2.3. Measurement Uncertainty.................................................................................. 20

2.4. Test Environment ............................................................................................... 22

3. Conducted Emission (Main Terminals)...................................................................... 23

3.1. Test Specification............................................................................................... 23

3.2. Test Setup.......................................................................................................... 23

3.3. Limit ................................................................................................................... 23

3.4. Test Procedure .................................................................................................. 24

3.5. Deviation from Test Standard............................................................................. 24

3.6. Test Result ......................................................................................................... 25

3.7. Test Photograph ................................................................................................ 49

4. Conducted Emissions (Telecommunication Ports).................................................... 53


4.2. Test Setup.......................................................................................................... 53

4.3. Limit ................................................................................................................... 53

4.4. Test Procedure .................................................................................................. 54


4.6. Test Result ......................................................................................................... 55

4.7. Test Photograph ................................................................................................ 91

5. Radiated Emission.................................................................................................... 95


5.2. Test Setup.......................................................................................................... 95

5.3. Limit ................................................................................................................... 96

5.4. Test Procedure .................................................................................................. 97


5.6. Test Result ......................................................................................................... 98

5.7. Test Photograph .............................................................................................. 122

6. Harmonic Current Emission .................................................................................... 128


Page: 5 of 217

6.1. Test Specification............................................................................................. 128

6.2. Test Setup........................................................................................................ 128

6.3. Limit ................................................................................................................. 128

6.4. Test Procedure ................................................................................................ 130

6.5. Deviation from Test Standard........................................................................... 130

6.6. Test Result ....................................................................................................... 131

7. Voltage Fluctuation and Flicker............................................................................... 141


7.2. Test Setup........................................................................................................ 141

7.3. Limit ................................................................................................................. 141

7.4. Test Procedure ................................................................................................ 142


7.6. Test Result ....................................................................................................... 143

7.7. Test Photograph .............................................................................................. 147

8. Electrostatic Discharge ........................................................................................... 149


8.2. Test Setup........................................................................................................ 149

8.3. Limit ................................................................................................................. 149

8.4. Test Procedure ................................................................................................ 150


8.6. Test Result ....................................................................................................... 151

8.7. Test Photograph .............................................................................................. 155

9. Radiated Susceptibility ........................................................................................... 157


9.2. Test Setup........................................................................................................ 157

9.3. Limit ................................................................................................................. 157

9.4. Test Procedure ................................................................................................ 158


9.6. Test Result ....................................................................................................... 159

9.7. Test Photograph .............................................................................................. 163

10. Electrical Fast Transient/Burst ......................................................................... 165


10.2. Test Setup........................................................................................................ 165

10.3. Limit ................................................................................................................. 165

10.4. Test Procedure ................................................................................................ 166


10.6. Test Result ....................................................................................................... 167

10.7. Test Photograph .............................................................................................. 171


Page: 6 of 217

11. Surge ............................................................................................................... 175


11.2. Test Setup........................................................................................................ 175

11.3. Limit ................................................................................................................. 175

11.4. Test Procedure ................................................................................................ 176


11.6. Test Result ....................................................................................................... 177

11.7. Test Photograph .............................................................................................. 181

12. Conducted Susceptibility ................................................................................. 183


12.2. Test Setup........................................................................................................ 183

12.3. Limit ................................................................................................................. 184

12.4. Test Procedure ................................................................................................ 184


12.6. Test Result ....................................................................................................... 185

12.7. Test Photograph .............................................................................................. 189

13. Power Frequency Magnetic Field .................................................................... 193


13.2. Test Setup........................................................................................................ 193

13.3. Limit ................................................................................................................. 193

13.4. Test Procedure ................................................................................................ 193


13.6. Test Result ....................................................................................................... 194

13.7. Test Photograph .............................................................................................. 198

14. Voltage Dips and Interruption........................................................................... 199


14.2. Test Setup........................................................................................................ 200

14.3. Limit ................................................................................................................. 200

14.4. Test Procedure ................................................................................................ 201


14.6. Test Result ....................................................................................................... 202

14.7. Test Photograph .............................................................................................. 206

15. Attachment ...................................................................................................... 208

　 EUT Photograph .............................................................................................. 208


Page: 7 of 217

1. General Information 1.1. EUT Description

Product Name Notebook PC

Trade Name msi

Model No. MS-16Y1

Component

Power Adapter #1 MFR: DELTA, M/N: ADP-65JH CB

Input: AC 100-240V, 50-60Hz, 2.0A

Output: DC 19V, 3.42A

Cable Out: Non-Shielded, 1.8m, with one ferrite core bonded.

Power Adapter #2 MFR: DELTA, M/N: ADP-65JH BB

Input: AC 100-240V, 50-60Hz, 1.5A



Power Adapter #3 MFR: DELTA, M/N: ADP-90CD DB

Input: AC 100-240V, 50-60Hz, 1.5A



Power Adapter #4 MFR: LITEON, M/N: PA-1900-36

Input: AC 100-240V, 50-60Hz, 1.5A




Page: 8 of 217

Keyparts List

Component Vendor Model Name Comments

Motherboard

PEGATRON A15HC --

CPU (Pin:988)

Intel i5-2410M, DC, 35W DC, 2.3GHz,L3:3M, 35W , PGA988,

Intel i3-2310M, DC, 35W DC, 2.3GHz,L3:3M, 35W , PGA988,

VGA

nVidia N12P-GV2+Samsung 1GB VRM 40-nm process,29mmx29mm,C.S GB2-128 FCBGA973,20W

VRAM 64x16(512Mb - 4pcs, 1Gbit - 8pcs ) DDR3

Samsung K4W1G1646E-HC11 DDR3 1600 64M*16-1.5V FBGA-96

15.6 HD LED (1366x768)

Samsung LTN156AT05-H02 358.8x209.0x5.5mm

INNOLUX BT156GW01 359.8x210x5.5mm

12.7 mm SATA ODD

Super Multi PIONEER DVR-TD10RS SLIM SATA DVD SM DL F/W:1.00

Blu-Ray Combo

PLDS DS-4E1S SLIM SATA BD COMBO FW:EP81

2.5" SATA HDD

WD WD6400BPVT-xxHXZT1 SATA Scorpio®Blue ML320S-AF, 6400GB, 5400 RPM9.5 mm height (4K sector) WD WD7500BPVT-xxHXZTx SATA Scorpio®Blue ML320S-AF, 750GB, 5400 RPM

WLAN Module

Atheros AR5B95(AW-NE785H ) 802.11 1x1 b/g/n, Atheros AR9285L, PCIE interface

WLAN+BT Combo Module

Atheros AR5B195(Chicony/WB214E) 802.11b/g/n 1x1+BT 3.0 EDR, Atheros AR9285L+AR3011, PCIE for Wifi, USB3.0 for BT

Keyboard

Monterey NK81MT09-00000T-01/A Montetery-340mm, frame type w/num US

Monterey NK81MT09-01003D-01/A Montetery-340mm, frame type w/num UK

Touchpad

Sent C8048D-7300 TBD

Battery

PEGATRON A42-A15 14.4Vdc, 4400mAh or 14.6Vdc,5200mAh

PEGATRON A32-A15 10.8Vdc, 4400mAh

Adaptor

90W DELTA ADP-90CD DB Adapter 90W, 3PIN, Energy Star level 5

LITEON PA-1900-36 Adapter 90W, 3PIN, Energy Star level 5

65W DELTA ADP-65JH CB Adapter 65W, 2PIN, Liteon LOGO

DELTA ADP-65JH BB Adapter 65W 3PIN, DELTA LOG

1GB DDR3-1333 SO-DIMM

Elixir M2S1G64CBH4B5P-CG DDRIII1333 SO-D 1GB 204P


Page: 9 of 217

ASINT SSY3128M8-EDJEF DDRIII 1333 SO-D 1GB 204P

2GB DDR3-1333 SO-DIMM

Elixir M2S2G64CB88B5N-CG DDRIII1333 SO-DIM 2GB 204P

HYNIX HMT325S6BFR8C-H9N0 DDRIII1333 SO-D 2G B-DIE 204P

Fixed Camera Module

Foxlink FE13FF-231H-3 60x8x4.74mm, Sensor: SET SIM120C-10N, IC: RTS5801-GR, LENS: LARGAN 9317D 1.3M

Chicony CNF915321005111LH 60x8x5.03(w/tape), Sensor: S5K6AA, IC: AU3831,

LENS: NewMax 2P


Page: 10 of 217

1.2. Mode of Operation QuieTek has verified the construction and function in typical operation. All the test modes were

carried out with the EUT in normal operation, which was shown in this test report and defined as:

Pre-Test Mode Mode 1 Mode 2 Mode 3 Mode 4 Final Test Mode

Emission

Mode 1 Mode 2 Mode 3 Mode 4

Immunity

Mode 1 Mode 2 Mode 3 Mode 4

Mode 1

LCD+D-SUB (1366*768/60Hz) Mode 2

LCD+HDMI (1366*768/60Hz)

CPU Intel/i5-2410M, DC, 35W Intel/i3-2310M, DC, 35W

MB PEGATRON /A15HC PEGATRON /A15HC

15.6 HD LED

(1366x768) Samsung/LTN156AT05-H02 INNOLUX/BT156GW01

12.7 mm SATA

ODD PLDS/DS-4E1S PIONEER/DVR-TD10RS

2.5" SATA HDD WD/WD7500BPVT-xxHXZTx WD/WD6400BPVT-xxHXZT1

WLAN Module N/A Atheros/ AR5B95(AW-NE785H )

WLAN+BT

Combo Module Atheros/ AR5B195(Chicony/WB214E) N/A

Battery PEGATRON/A42-A15 PEGATRON/A32-A15

Adaptor DELTA/ADP-90CD DB LITEON/PA-1900-36

DDR HYNIX/HMT325S6BFR8C-H9N0 Elixir/M2S2G64CB88B5N-CG

Camera Chicony/CNF915321005111LH Foxlink/FE13FF-231H-3


Page: 11 of 217

Mode 3

LCD+D-SUB (1366*768/60Hz) Mode 4

LCD+D-SUB (1366*768/60Hz)

CPU Intel/i3-2310M, DC, 35W Intel/i3-2310M, DC, 35W

MB PEGATRON /A15HC PEGATRON /A15HC

15.6 HD LED

(1366x768) Samsung/LTN156AT05-H02 INNOLUX/BT156GW01

12.7 mm SATA

ODD PLDS/DS-4E1S PIONEER/DVR-TD10RS

2.5" SATA HDD WD/WD7500BPVT-xxHXZTx WD/WD6400BPVT-xxHXZT1

WLAN Module N/A Atheros/ AR5B95(AW-NE785H )

WLAN+BT

Combo Module Atheros/ AR5B195(Chicony/WB214E) N/A

Battery PEGATRON/A42-A15 PEGATRON/A32-A15

Adaptor DELTA/ADP-65JH BB DELTA/ADP-65JH CB

DDR ASINT/SSY3128M8-EDJEF Elixir/M2S1G64CBH4B5P-CG

Camera Chicony/CNF915321005111LH Foxlink/FE13FF-231H-3


Page: 12 of 217

1.3. Tested System Details The types for all equipments, plus descriptions of all cables used in the tested system (including

inserted cards) are:

Product Manufacturer Model No. Serial No. Power Cord

1 Monitor (EMI) Dell 3008WFPt CN-0G501H-74443-8BK-005L Non-Shielded, 1.8m

Monitor (EMS) Dell U2410f CN-0J257M-72872-985-0JML Shielded, 1.5m

2 USB 3.0 BUFFALO HD-H1.0TU3 15476991119984 Shielded, 1.5m

3 USB 3.0 BUFFALO HD-H1.0TU3 15476991119601 N/A

Microphone &

Earphone (EMI)

PCHOME N/A N/A N/A 4

Microphone &

Earphone (EMS)

Ergotech ET-E201 N/A N/A

5 USB Mouse (EMI) Logitech M-UV83 LNA34515276 N/A

USB Mouse (EMS) Logitech M-UAL-96 LZ923A40006 N/A

DELL HDD(80G)

(EMI)

DELL RD1000 BGPWZD1

848200184144

N/A 6

IPod nano (EMS) Apple A1199 YM706LSCVQ5 N/A

7 Notebook PC DELL PP04X C8YYM1S Non-Shielded, 0.8m


Page: 13 of 217

1.4. Configuration of Tested System EMI

Connection Diagram

Signal Cable Type Signal cable Description

A D-SUB Cable Shielded, 1.8m with two ferrite cores bonded

B HDMI Cable Shielded, 1.0m

C USB 3.0 Cable Shielded, 1.0m, two PCS.

D Microphone & Earphone Cable Non-Shielded, 1.6m

E USB Cable Shielded, 1.5m

F LAN Cable Non-Shielded, 3.0m

G USB Cable Shielded, 1.2m


Page: 14 of 217

EMS Connection Diagram

Signal Cable Type Signal cable Description

A D-SUB Cable Shielded, 1.8m with two ferrite cores bonded

B HDMI Cable Shielded, 1.0m

C USB 3.0 Cable Shielded, 1.0m, two PCS.

D Microphone & Earphone Cable Non-Shielded, 1.6m

E USB Cable Shielded, 1.5m

F LAN Cable Non-Shielded, 3.0m

G USB Cable Shielded, 1.2m


Page: 15 of 217

1.5. EUT Exercise Software

1 Setup the EUT and peripheral as shown on Figure

2 Connect the power to EUT and peripherals, then turn on the power of all equipments.

3 Waiting for EUT to enter Vista Operating System, and adjust the display resolution to the test mode first.

4 Connect LAN to Notebook PCPC for transmitting data.

5 Activate Wireless interface and Bluetooth function, and perform the wireless data communication with the other Notebook PC(write/delete action).

6 Run Windows Media Player program and play a disk with color Bar pattern

7 Carry out the function of the EUT cell-phone and platform of simulation base of cell-phone and do the line

8 Run “H＂ pattern.

9 Begin to test and repeat the above procedure (4)~(7)


Page: 16 of 217

2. Technical Test

2.1. Summary of Test Result

No deviations from the test standards

Deviations from the test standards as below description:

Emission

Performed Item Normative References Test

Performed Deviation

Conducted Emission EN 55022: 2006+A1: 2007 Yes No

Impedance Stabilization Network EN 55022: 2006+A1: 2007 Yes No

Radiated Emission EN 55022: 2006+A1: 2007 Yes No

Power Harmonics EN 61000-3-2: 2006+A2: 2009 Yes No

Voltage Fluctuation and Flicker EN 61000-3-3: 2008 Yes No

Immunity

Performed Item Normative References Test

Performed Deviation

Electrostatic Discharge IEC 61000-4-2: 2008 Yes No

Radiated susceptibility IEC 61000-4-3: 2008 Yes No

Electrical fast transient/burst IEC 61000-4-4: 2004 Yes No

Surge IEC 61000-4-5: 2005 Yes No

Conducted susceptibility IEC 61000-4-6: 2008 Yes No

Power frequency magnetic field IEC 61000-4-8: 2009 Yes No

Voltage dips and interruption IEC 61000-4-11: 2004 Yes No


Page: 17 of 217

2.2. List of Test Equipment Conducted Emission / SR1 Instrument Manufacturer Type No. Serial No Cal. Date EMI Test Receiver R&S ESCS 30 100366 2010/10/29 LISN R&S ENV4200 833209/007 2010/08/14 LISN R&S ENV216 100085 2010/02/17 Pulse Limiter R&S ESH3-Z2 357.88.10.52 2010/09/10 Impedance Stabilization Network / SR1 Instrument Manufacturer Type No. Serial No Cal. Date Capacitive Voltage Probe Schaffner CVP2200A 18331 2010/11/16 EMI Test Receiver R&S ESCS 30 100366 2010/10/29 LISN R&S ENV216 100085 2010/02/17 LISN R&S ENV4200 833209/007 2010/08/14 Pulse Limiter R&S ESH3-Z2 357.88.10.52 2010/09/10 RF Current Probe FCC F-65 10KHz~1GHz 198 2010/11/13 BALANCED TELECOM ISN FCC FCC-TLISN-T2-02 20316 2010/11/22 BALANCED TELECOM ISN FCC FCC-TLISN-T4-02 20317 2010/11/22 BALANCED TELECOM ISN FCC FCC-TLISN-T8-02 20319 2010/11/22 Radiated Emission / Site5 Instrument Manufacturer Type No. Serial No Cal. Date Bilog Antenna Schaffner Chase CBL6112B 2920 2010/08/01 Broadband Horn Antenna Schwarzbeck BBHA9170 209 2010/07/25 EMI Test Receiver R&S ESCS 30 825442/018 2010/10/12 Horn Antenna Schwarzbeck BBHA9120D 305 2010/08/26 Pre-Amplifier QTK N/A N/A 2010/08/01 Spectrum Analyzer Advantest R3162 100803463 2010/12/16

Radiated Emission / 9x6x6_Chamber Instrument Manufacturer Type No. Serial No Cal. Date Spectrum Analyzer (9K-26.5GHz)

Agilent E4408B MY45102743 2010/08/12

Horn Antenna Schwarzbeck 9120D 576 2010/10/21 Pre-Amplifier QuieTek AP-180C CHM/071920 2010/08/04 Power Harmonics / SR3 Instrument Manufacturer Type No. Serial No Cal. Date AC Power Source(Harmonic)

Schaffner NSG 1007 HK54148 2010/08/11

IEC1000-4-X Analyzer(Flicker)

Schaffner CCN 1000-1 X7 1887 2010/08/11

Voltage Fluctuation and Flicker / SR3 Instrument Manufacturer Type No. Serial No Cal. Date AC Power Source(Harmonic)

Schaffner NSG 1007 HK54148 2010/08/11

IEC1000-4-X Analyzer(Flicker)

Schaffner CCN 1000-1 X7 1887 2010/08/11


Page: 18 of 217

Electrostatic Discharge / SR6 Instrument Manufacturer Type No. Serial No Cal. Date ESD Simulator System Noiseken TC-815R ESS0929097 2010/07/06 Horizontal Coupling Plane(HCP)

QuieTek HCP AL50 N/A N/A

Vertical Coupling Plane(VCP)

QuieTek VCP AL50 N/A N/A

Radiated susceptibility / CB5 Instrument Manufacturer Type No. Serial No Cal. Date

AF-BOX R&S AF-BOX ACCUST

100007 N/A

Audio Analyzer R&S UPL 16 100137 2010/04/15 Biconilog Antenna EMCO 3149 00071675 N/A Directional Coupler A&R DC 6180 22735 N/A Dual Microphone Supply B&K 5935 2426784 2010/04/16 Mouth Simulator B&K 4227 2439692 2010/04/16 Power Amplifier A&R 30S1G3 309453 N/A Power Amplifier A&R 100W10000M7 A285000010 N/A Power Amplifier SCHAFFNER CBA9413B 4020 N/A Power Amplifier AR 75A250A 0325371 N/A Power Meter R&S NRVD(P.M) 100219 2010/04/16 Pre-Amplifier A&R 150A220 23067 N/A Probe Microphone B&K 4182 2278070 2010/04/16 Signal Generator R&S SML03 103330 2010/04/16 Electrical fast transient/burst / SR6 Instrument Manufacturer Type No. Serial No Cal. Date EMC immunity system Thermo EMCPRO PLUS 0411225 2010/03/10 Surge / SR6 Instrument Manufacturer Type No. Serial No Cal. Date EMC immunity system Thermo EMCPRO PLUS 0411225 2010/03/10 Conducted susceptibility / SR6 Instrument Manufacturer Type No. Serial No Cal. Date Schaffner NSG 2070 RF-Generator

Schaffner N/A N/A 2010/04/21

Power frequency magnetic field / SR3 Instrument Manufacturer Type No. Serial No Cal. Date Induction Coil Interface Schaffner INA 2141 6002 N/A Magnetic Loop Coil Schaffner INA 702 160 N/A Triaxial ELF Magnetic Field Meter

F.B.BELL 4090 114135 2010/03/27

Voltage dips and interruption / SR6 Instrument Manufacturer Type No. Serial No Cal. Date EMC immunity system Thermo EMCPRO PLUS 0411225 2010/03/10


Page: 19 of 217

Schaffner NSG 2070 RF-Generator Instrument Manufacturer Type No. Serial No Cal. Date CDN Schaffner CAL U100A 20405 N/A CDN Schaffner TRA U150 20454 N/A CDN M016S Schaffner CAL U100A 20410 N/A CDN M016S Schaffner TRA U150 21167 N/A CDN T002 Schaffner CAL U100 20491 N/A CDN T002 Schaffner TRA U150 21169 N/A CDN T400 Schaffner CAL U100 17735 N/A CDN T400 Schaffner TRA U150 21166 N/A Coupling Decoupling Network

Schaffner CDN M016S 20823 2010/04/02

Coupling Decoupling Network

Schaffner CDN T002 19018 2010/04/02

Coupling Decoupling Network

Schaffner CDN T400 21226 2010/04/02

EM-CLAMP Schaffner KEMZ 801 21024 2010/04/02


Page: 20 of 217

2.3. Measurement Uncertainty Conducted Emission

The measurement uncertainty is evaluated as ± 2.26 dB.

Impedance Stabilization Network


Radiated Emission


Electrostatic Discharge

As what is concluded in the document from Note2 of clause 5.4.6.2 of ISO/IEC 17025:

1999[2], the requirements for measurement uncertainty in ESD testing are deemed to have

been satisfied, and the testing is reported in accordance with the relevant ESD standards.

The immunity test signal from the ESD system meet the required specifications in IEC

61000-4-2 through the calibration report with the calibrated uncertainty for the waveform of

voltage and timing as being 1.0 % and 0.1%.

Radiated susceptibility


1999[2], the requirements for measurement uncertainty in RS testing are deemed to have

been satisfied, and the testing is reported in accordance with the relevant RS standards.

The immunity test signal from the RS system meet the required specifications in IEC

61000-4-3 through the calibration for the uniform field strength and monitoring for the test

level with the uncertainty evaluation report for the electrical filed strength as being 3.57 dB.

Electrical fast transient/burst


1999[2], the requirements for measurement uncertainty in EFT/Burst testing are deemed to

have been satisfied, and the testing is reported in accordance with the relevant EFT/Burst

standards. The immunity test signal from the EFT/Burst system meet the required

specifications in IEC 61000-4-4 through the calibration report with the calibrated uncertainty

for the waveform of voltage, frequency and timing as being 4 %, and 2.5%.

Surge


1999[2], the requirements for measurement uncertainty in Surge testing are deemed to

have been satisfied, and the testing is reported in accordance with the relevant Surge

standards. The immunity test signal from the Surge system meet the required specifications

in IEC 61000-4-5 through the calibration report with the calibrated uncertainty for the

waveform of voltage and timing as being 3.5 % and 0.1%.

Conducted susceptibility


1999[2], the requirements for measurement uncertainty in CS testing are deemed to have


Page: 21 of 217

been satisfied, and the testing is reported in accordance with the relevant CS standards.

The immunity test signal from the CS system meet the required specifications in IEC

61000-4-6 through the calibration for unmodulated signal and monitoring for the test level

with the uncertainty evaluation report for the injected modulated signal level through CDN

and EM Clamp/Direct Injection as being 2.0 dB and 2.61 dB.

Power frequency magnetic field


1999[2], the requirements for measurement uncertainty in PFM testing are deemed to have

been satisfied, and the testing is reported in accordance with the relevant PFM standards.

The immunity test signal from the PFM system meet the required specifications in IEC

61000-4-8 through the calibration report with the calibrated uncertainty for the Gauss Meter

to verify the output level of magnetic field strength as being 2.0 %.

Voltage dips and interruption


1999[2], the requirements for measurement uncertainty in DIP testing are deemed to have

been satisfied, and the testing is reported in accordance with the relevant DIP standards.

The immunity test signal from the DIP system meet the required specifications in IEC

61000-4-11 through the calibration report with the calibrated uncertainty for the waveform of

voltage and timing as being 3.5 % and 0.1%.


Page: 22 of 217

2.4. Test Environment Performed Item Items Required Actual

Temperature (C) 15-35 25

Conducted Emission Humidity (%RH) 25-75 50

Barometric pressure (mbar) 860-1060 950-1000


Impedance Stabilization Network Humidity (%RH) 25-75 50



Radiated Emission Humidity (%RH) 25-75 50



Electrostatic Discharge Humidity (%RH) 30-60 48



Radiated susceptibility Humidity (%RH) 25-75 56



Electrical fast transient/burst Humidity (%RH) 25-75 49



Surge Humidity (%RH) 10-75 49



Conducted susceptibility Humidity (%RH) 25-75 49



Power frequency magnetic field Humidity (%RH) 25-75 53



Voltage dips and interruption Humidity (%RH) 25-75 47



Page: 23 of 217

3. Conducted Emission (Main Terminals)

3.1. Test Specification

According to EMC Standard: EN 55022

3.2. Test Setup

3.3. Limit

Limits

Frequency (MHz)

QP (dBuV)

AV (dBuV)

0.15 - 0.50 66 - 56 56 – 46

0.50-5.0 56 46

5.0 - 30 60 50

Remarks: In the above table, the tighter limit applies at the band edges.


Page: 24 of 217

3.4. Test Procedure

The EUT and simulators are connected to the main power through a line impedance

stabilization network (L.I.S.N.). This provides a 50 ohm /50uH coupling impedance for the

measuring equipment. The peripheral devices are also connected to the main power through

a LISN that provides a 50ohm/50uH coupling impedance with 50ohm termination.

(Please refers to the block diagram of the test setup and photographs.)

Both sides of A.C. line are checked for maximum conducted interference. In order to find the

maximum emission, the relative positions of equipment and all of the interface cables must

be changed on conducted measurement.

Conducted emissions were invested over the frequency range from 0.15MHz to 30MHz using

a receiver bandwidth of 9kHz.

3.5. Deviation from Test Standard

No deviation.


Page: 25 of 217

3.6. Test Result Site : SR_1 Time : 2010/12/27 - 23:01

Limit : CISPR_B_00M_QP Margin : 10

EUT : Notebook P.C. Probe : ENV_216_L1 - Line1

Power : AC 230V/50Hz Note : Mode 1


Page: 26 of 217

Site : SR_1 Time : 2010/12/27 - 23:02




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.158 9.790 44.920 54.710 -11.061 65.771 QUASIPEAK

2 0.244 9.790 38.660 48.450 -14.864 63.314 QUASIPEAK

3 0.404 9.790 35.860 45.650 -13.093 58.743 QUASIPEAK

4 * 0.643 9.790 39.710 49.500 -6.500 56.000 QUASIPEAK

5 0.795 9.800 37.590 47.390 -8.610 56.000 QUASIPEAK

6 7.455 9.850 36.450 46.300 -13.700 60.000 QUASIPEAK

Note:

1. All Reading Levels are Quasi-Peak and average value.

2. " * ", means this data is the worst emission level.

3. Measurement Level = Reading Level + Correct Factor


Page: 27 of 217

Site : SR_1 Time : 2010/12/27 - 23:02

Limit : CISPR_B_00M_AV Margin : 0



Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.158 9.790 33.730 43.520 -12.251 55.771 AVERAGE

2 0.244 9.790 31.360 41.150 -12.164 53.314 AVERAGE

3 0.404 9.790 25.110 34.900 -13.843 48.743 AVERAGE

4 * 0.643 9.790 26.530 36.320 -9.680 46.000 AVERAGE

5 0.795 9.800 24.600 34.400 -11.600 46.000 AVERAGE

6 7.455 9.850 28.660 38.510 -11.490 50.000 AVERAGE

Note:





Page: 28 of 217

Site : SR_1 Time : 2010/12/27 - 23:03


EUT : Notebook P.C. Probe : ENV_216_N - Line2



Page: 29 of 217

Site : SR_1 Time : 2010/12/27 - 23:04




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.154 9.782 45.540 55.322 -10.564 65.886 QUASIPEAK

2 0.236 9.780 32.050 41.830 -21.713 63.543 QUASIPEAK

3 * 0.599 9.790 39.020 48.810 -7.190 56.000 QUASIPEAK

4 0.658 9.790 36.480 46.270 -9.730 56.000 QUASIPEAK

5 0.923 9.790 30.090 39.880 -16.120 56.000 QUASIPEAK

6 8.306 9.880 33.210 43.090 -16.910 60.000 QUASIPEAK

Note:





Page: 30 of 217

Site : SR_1 Time : 2010/12/27 - 23:04




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.154 9.782 27.770 37.552 -18.334 55.886 AVERAGE

2 0.236 9.780 15.200 24.980 -28.563 53.543 AVERAGE

3 * 0.599 9.790 28.220 38.010 -7.990 46.000 AVERAGE

4 0.658 9.790 26.180 35.970 -10.030 46.000 AVERAGE

5 0.923 9.790 18.210 28.000 -18.000 46.000 AVERAGE

6 8.306 9.880 24.440 34.320 -15.680 50.000 AVERAGE

Note:





Page: 31 of 217

Site : SR_1 Time : 2010/12/30 - 09:49





Page: 32 of 217

Site : SR_1 Time : 2010/12/30 - 09:51




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.180 9.790 26.420 36.210 -28.933 65.143 QUASIPEAK

2 0.271 9.790 20.760 30.550 -31.993 62.543 QUASIPEAK

3 0.391 9.790 20.240 30.030 -29.084 59.114 QUASIPEAK

4 2.263 9.810 24.300 34.110 -21.890 56.000 QUASIPEAK

5 * 4.791 9.830 24.630 34.460 -21.540 56.000 QUASIPEAK

6 13.357 10.100 26.240 36.340 -23.660 60.000 QUASIPEAK

Note:





Page: 33 of 217

Site : SR_1 Time : 2010/12/30 - 09:51




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.180 9.790 24.550 34.340 -20.803 55.143 AVERAGE

2 0.271 9.790 15.050 24.840 -27.703 52.543 AVERAGE

3 0.391 9.790 8.660 18.450 -30.664 49.114 AVERAGE

4 2.263 9.810 19.260 29.070 -16.930 46.000 AVERAGE

5 * 4.791 9.830 19.270 29.100 -16.900 46.000 AVERAGE

6 13.357 10.100 21.090 31.190 -18.810 50.000 AVERAGE

Note:





Page: 34 of 217

Site : SR_1 Time : 2010/12/30 - 09:52





Page: 35 of 217

Site : SR_1 Time : 2010/12/30 - 09:54




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.259 9.780 30.730 40.510 -22.376 62.886 QUASIPEAK

2 0.360 9.790 27.430 37.220 -22.780 60.000 QUASIPEAK

3 * 0.730 9.790 27.310 37.100 -18.900 56.000 QUASIPEAK

4 1.834 9.800 23.360 33.160 -22.840 56.000 QUASIPEAK

5 12.103 10.017 25.580 35.597 -24.403 60.000 QUASIPEAK

6 17.900 10.200 25.770 35.970 -24.030 60.000 QUASIPEAK

Note:





Page: 36 of 217

Site : SR_1 Time : 2010/12/30 - 09:54




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.259 9.780 19.170 28.950 -23.936 52.886 AVERAGE

2 0.360 9.790 17.210 27.000 -23.000 50.000 AVERAGE

3 0.730 9.790 16.430 26.220 -19.780 46.000 AVERAGE

4 * 1.834 9.800 17.950 27.750 -18.250 46.000 AVERAGE

5 12.103 10.017 20.390 30.407 -19.593 50.000 AVERAGE

6 17.900 10.200 19.360 29.560 -20.440 50.000 AVERAGE

Note:





Page: 37 of 217

Site : SR_1 Time : 2010/12/29 - 00:20





Page: 38 of 217

Site : SR_1 Time : 2010/12/29 - 00:21




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.201 9.790 46.490 56.280 -8.263 64.543 QUASIPEAK

2 0.470 9.790 38.030 47.820 -9.037 56.857 QUASIPEAK

3 * 0.670 9.790 39.290 49.080 -6.920 56.000 QUASIPEAK

4 0.970 9.800 37.690 47.490 -8.510 56.000 QUASIPEAK

5 1.322 9.800 36.150 45.950 -10.050 56.000 QUASIPEAK

6 3.341 9.820 33.870 43.690 -12.310 56.000 QUASIPEAK

Note:





Page: 39 of 217

Site : SR_1 Time : 2010/12/29 - 00:21




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 * 0.201 9.790 34.950 44.740 -9.803 54.543 AVERAGE

2 0.470 9.790 25.710 35.500 -11.357 46.857 AVERAGE

3 0.670 9.790 24.690 34.480 -11.520 46.000 AVERAGE

4 0.970 9.800 24.610 34.410 -11.590 46.000 AVERAGE

5 1.322 9.800 20.660 30.460 -15.540 46.000 AVERAGE

6 3.341 9.820 24.100 33.920 -12.080 46.000 AVERAGE

Note:





Page: 40 of 217

Site : SR_1 Time : 2010/12/29 - 00:21





Page: 41 of 217

Site : SR_1 Time : 2010/12/29 - 00:22




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.201 9.780 45.270 55.050 -9.493 64.543 QUASIPEAK

2 0.392 9.790 37.070 46.860 -12.226 59.086 QUASIPEAK

3 0.466 9.790 38.490 48.280 -8.691 56.971 QUASIPEAK

4 * 0.677 9.790 39.790 49.580 -6.420 56.000 QUASIPEAK

5 0.943 9.790 36.850 46.640 -9.360 56.000 QUASIPEAK

6 1.513 9.800 34.870 44.670 -11.330 56.000 QUASIPEAK

Note:





Page: 42 of 217

Site : SR_1 Time : 2010/12/29 - 00:22




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.201 9.780 33.870 43.650 -10.893 54.543 AVERAGE

2 0.392 9.790 26.140 35.930 -13.156 49.086 AVERAGE

3 0.466 9.790 26.210 36.000 -10.971 46.971 AVERAGE

4 * 0.677 9.790 25.410 35.200 -10.800 46.000 AVERAGE

5 0.943 9.790 23.010 32.800 -13.200 46.000 AVERAGE

6 1.513 9.800 22.760 32.560 -13.440 46.000 AVERAGE

Note:





Page: 43 of 217

Site : SR_1 Time : 2010/12/23 - 04:44





Page: 44 of 217

Site : SR_1 Time : 2010/12/23 - 04:45




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 * 0.212 9.790 44.430 54.220 -10.009 64.229 QUASIPEAK

2 0.322 9.790 36.030 45.820 -15.266 61.086 QUASIPEAK

3 0.525 9.790 33.510 43.300 -12.700 56.000 QUASIPEAK

4 0.646 9.790 33.750 43.540 -12.460 56.000 QUASIPEAK

5 4.248 9.820 30.510 40.330 -15.670 56.000 QUASIPEAK

6 16.541 10.110 25.870 35.980 -24.020 60.000 QUASIPEAK

Note:





Page: 45 of 217

Site : SR_1 Time : 2010/12/23 - 04:45




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 * 0.212 9.790 39.720 49.510 -4.719 54.229 AVERAGE

2 0.322 9.790 31.870 41.660 -9.426 51.086 AVERAGE

3 0.525 9.790 22.220 32.010 -13.990 46.000 AVERAGE

4 0.646 9.790 26.880 36.670 -9.330 46.000 AVERAGE

5 4.248 9.820 15.090 24.910 -21.090 46.000 AVERAGE

6 16.541 10.110 14.510 24.620 -25.380 50.000 AVERAGE

Note:





Page: 46 of 217

Site : SR_1 Time : 2010/12/23 - 04:46





Page: 47 of 217

Site : SR_1 Time : 2010/12/23 - 04:47




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.220 9.780 41.790 51.570 -12.430 64.000 QUASIPEAK

2 0.318 9.790 34.570 44.360 -16.840 61.200 QUASIPEAK

3 * 0.537 9.790 33.870 43.660 -12.340 56.000 QUASIPEAK

4 0.646 9.790 33.570 43.360 -12.640 56.000 QUASIPEAK

5 4.076 9.820 27.310 37.130 -18.870 56.000 QUASIPEAK

6 15.486 10.180 27.010 37.190 -22.810 60.000 QUASIPEAK

Note:





Page: 48 of 217

Site : SR_1 Time : 2010/12/23 - 04:47




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.220 9.780 32.640 42.420 -11.580 54.000 AVERAGE

2 0.318 9.790 29.750 39.540 -11.660 51.200 AVERAGE

3 * 0.537 9.790 28.980 38.770 -7.230 46.000 AVERAGE

4 0.646 9.790 26.410 36.200 -9.800 46.000 AVERAGE

5 4.076 9.820 13.670 23.490 -22.510 46.000 AVERAGE

6 15.486 10.180 15.280 25.460 -24.540 50.000 AVERAGE

Note:





Page: 49 of 217

3.7. Test Photograph Test Mode : Mode 1

Description : Front View of Conducted Test

Test Mode : Mode 1

Description : Back View of Conducted Test


Page: 50 of 217

Test Mode : Mode 2


Test Mode : Mode 2



Page: 51 of 217

Test Mode : Mode 3


Test Mode : Mode 3



Page: 52 of 217

Test Mode : Mode 4


Test Mode : Mode 4



Page: 53 of 217

4. Conducted Emissions (Telecommunication Ports)


According to EMC Standard : EN 55022

4.2. Test Setup

4.3. Limit

Limits

Frequency (MHz)

QP (dBuV)

AV (dBuV)

0.15 - 0.50 84 – 74 74 – 64

0.50 - 30 74 64

Remarks:

The limit decreases linearly with the logarithm of the frequency in the range 0.15 MHz~0.50

MHz.


Page: 54 of 217

4.4. Test Procedure

Telecommunication Port:

The mains voltage shall be supplied to the EUT via the LISN when the measurement of

telecommunication port is performed. The common mode disturbances at the

telecommunication port shall be connected to the ISN, which is 150 ohm impedance.

Both alternative cables are tested related to the LCL requested. The measurement range is

from 150kHz to 30MHz. The bandwidth of measurement is set to 9kHz.

The 75dB LCL ISN is used for cat. 6 cable, the 65dB LCL ISN is used for cat. 5 cable, 55dB

LCL ISN is used for cat. 3.


No deviation.


Page: 55 of 217

4.6. Test Result Site : SR_1 Time : 2010/12/27 - 23:08

Limit : ISN_Voltage_B_00M_QP Margin : 10

EUT : Notebook P.C. Probe : ISN_T4 - Line1

Power : AC 230V/50Hz Note : Mode 1, ISN 10MB


Page: 56 of 217

Site : SR_1 Time : 2010/12/27 - 23:10




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.521 9.990 47.000 56.990 -17.010 74.000 QUASIPEAK

2 * 0.774 9.981 51.410 61.391 -12.609 74.000 QUASIPEAK

3 0.826 9.980 48.240 58.220 -15.780 74.000 QUASIPEAK

4 1.470 9.990 47.480 57.470 -16.530 74.000 QUASIPEAK

5 8.584 9.970 46.560 56.530 -17.470 74.000 QUASIPEAK

6 9.994 9.960 42.500 52.460 -21.540 74.000 QUASIPEAK

Note:





Page: 57 of 217

Site : SR_1 Time : 2010/12/27 - 23:10

Limit : ISN_Voltage_B_00M_AV Margin : 0



Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.521 9.990 38.050 48.040 -15.960 64.000 AVERAGE

2 * 0.774 9.981 48.560 58.541 -5.459 64.000 AVERAGE

3 0.826 9.980 38.220 48.200 -15.800 64.000 AVERAGE

4 1.470 9.990 36.890 46.880 -17.120 64.000 AVERAGE

5 8.584 9.970 39.640 49.610 -14.390 64.000 AVERAGE

6 9.994 9.960 28.550 38.510 -25.490 64.000 AVERAGE

Note:





Page: 58 of 217

Site : SR_1 Time : 2010/12/27 - 23:05





Page: 59 of 217

Site : SR_1 Time : 2010/12/27 - 23:08




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 * 0.773 9.981 51.490 61.471 -12.529 74.000 QUASIPEAK

2 1.548 9.990 49.420 59.410 -14.590 74.000 QUASIPEAK

3 1.938 10.000 46.940 56.940 -17.060 74.000 QUASIPEAK

4 8.447 9.970 44.950 54.920 -19.080 74.000 QUASIPEAK

5 13.357 10.150 48.440 58.590 -15.410 74.000 QUASIPEAK

6 16.228 10.130 49.860 59.990 -14.010 74.000 QUASIPEAK

Note:





Page: 60 of 217

Site : SR_1 Time : 2010/12/27 - 23:08




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 * 0.773 9.981 48.670 58.651 -5.349 64.000 AVERAGE

2 1.548 9.990 45.170 55.160 -8.840 64.000 AVERAGE

3 1.938 10.000 40.670 50.670 -13.330 64.000 AVERAGE

4 8.447 9.970 36.980 46.950 -17.050 64.000 AVERAGE

5 13.357 10.150 46.330 56.480 -7.520 64.000 AVERAGE

6 16.228 10.130 47.680 57.810 -6.190 64.000 AVERAGE

Note:





Page: 61 of 217

Site : SR_1 Time : 2010/12/27 - 23:11



Power : AC 230V/50Hz Note : Mode1 , ISN 1G


Page: 62 of 217

Site : SR_1 Time : 2010/12/27 - 23:14



Power : AC 230V/50Hz Note : Mode 1, ISN 1G

Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.614 10.150 48.490 58.640 -15.360 74.000 QUASIPEAK

2 * 0.773 10.131 51.810 61.941 -12.059 74.000 QUASIPEAK

3 1.550 10.090 50.690 60.780 -13.220 74.000 QUASIPEAK

4 2.267 10.070 47.720 57.790 -16.210 74.000 QUASIPEAK

5 3.931 10.060 45.900 55.960 -18.040 74.000 QUASIPEAK

6 8.267 10.060 44.040 54.100 -19.900 74.000 QUASIPEAK

Note:





Page: 63 of 217

Site : SR_1 Time : 2010/12/27 - 23:14




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.614 10.150 41.090 51.240 -12.760 64.000 AVERAGE

2 * 0.773 10.131 49.410 59.541 -4.459 64.000 AVERAGE

3 1.550 10.090 45.290 55.380 -8.620 64.000 AVERAGE

4 2.267 10.070 39.120 49.190 -14.810 64.000 AVERAGE

5 3.931 10.060 38.630 48.690 -15.310 64.000 AVERAGE

6 8.267 10.060 36.390 46.450 -17.550 64.000 AVERAGE

Note:





Page: 64 of 217

Site : SR_1 Time : 2010/12/28 - 23:32





Page: 65 of 217

Site : SR_1 Time : 2010/12/28 - 23:34




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 * 0.772 9.982 53.070 63.052 -10.948 74.000 QUASIPEAK

2 1.544 9.990 49.620 59.610 -14.390 74.000 QUASIPEAK

3 2.314 10.000 46.680 56.680 -17.320 74.000 QUASIPEAK

4 3.748 9.990 39.330 49.320 -24.680 74.000 QUASIPEAK

5 6.252 9.976 45.200 55.176 -18.824 74.000 QUASIPEAK

6 11.248 9.961 33.440 43.401 -30.599 74.000 QUASIPEAK

Note:





Page: 66 of 217

Site : SR_1 Time : 2010/12/28 - 23:34




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 * 0.772 9.982 51.830 61.812 -2.188 64.000 AVERAGE

2 1.544 9.990 47.600 57.590 -6.410 64.000 AVERAGE

3 2.314 10.000 42.050 52.050 -11.950 64.000 AVERAGE

4 3.748 9.990 29.820 39.810 -24.190 64.000 AVERAGE

5 6.252 9.976 34.830 44.806 -19.194 64.000 AVERAGE

6 11.248 9.961 33.430 43.391 -20.609 64.000 AVERAGE

Note:





Page: 67 of 217

Site : SR_1 Time : 2010/12/28 - 23:22





Page: 68 of 217

Site : SR_1 Time : 2010/12/28 - 23:24




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 * 0.771 9.982 52.950 62.932 -11.068 74.000 QUASIPEAK

2 1.545 9.990 48.950 58.940 -15.060 74.000 QUASIPEAK

3 2.322 10.000 44.240 54.240 -19.760 74.000 QUASIPEAK

4 7.923 9.970 44.350 54.320 -19.680 74.000 QUASIPEAK

5 14.213 10.140 46.850 56.990 -17.010 74.000 QUASIPEAK

6 16.228 10.130 49.050 59.180 -14.820 74.000 QUASIPEAK

Note:





Page: 69 of 217

Site : SR_1 Time : 2010/12/28 - 23:24




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 * 0.771 9.982 52.060 62.042 -1.958 64.000 AVERAGE

2 1.545 9.990 45.710 55.700 -8.300 64.000 AVERAGE

3 2.322 10.000 38.110 48.110 -15.890 64.000 AVERAGE

4 7.923 9.970 42.330 52.300 -11.700 64.000 AVERAGE

5 14.213 10.140 44.590 54.730 -9.270 64.000 AVERAGE

6 16.228 10.130 47.190 57.320 -6.680 64.000 AVERAGE

Note:





Page: 70 of 217

Site : SR_1 Time : 2010/12/28 - 23:19





Page: 71 of 217

Site : SR_1 Time : 2010/12/28 - 23:21




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 * 0.773 10.131 52.570 62.701 -11.299 74.000 QUASIPEAK

2 0.959 10.110 42.570 52.680 -21.320 74.000 QUASIPEAK

3 1.547 10.090 49.090 59.180 -14.820 74.000 QUASIPEAK

4 1.936 10.070 46.090 56.160 -17.840 74.000 QUASIPEAK

5 2.318 10.070 46.800 56.870 -17.130 74.000 QUASIPEAK

6 2.712 10.070 40.510 50.580 -23.420 74.000 QUASIPEAK

Note:





Page: 72 of 217

Site : SR_1 Time : 2010/12/28 - 23:21




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 * 0.773 10.131 51.260 61.391 -2.609 64.000 AVERAGE

2 0.959 10.110 36.630 46.740 -17.260 64.000 AVERAGE

3 1.547 10.090 46.430 56.520 -7.480 64.000 AVERAGE

4 1.936 10.070 41.930 52.000 -12.000 64.000 AVERAGE

5 2.318 10.070 42.100 52.170 -11.830 64.000 AVERAGE

6 2.712 10.070 35.590 45.660 -18.340 64.000 AVERAGE

Note:





Page: 73 of 217

Site : SR_1 Time : 2010/12/29 - 00:48





Page: 74 of 217

Site : SR_1 Time : 2010/12/29 - 00:49




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.189 10.037 52.890 62.927 -19.959 82.886 QUASIPEAK

2 0.388 10.000 45.690 55.690 -21.510 77.200 QUASIPEAK

3 * 0.748 9.990 53.130 63.120 -10.880 74.000 QUASIPEAK

4 1.490 9.990 47.070 57.060 -16.940 74.000 QUASIPEAK

5 3.423 9.990 35.910 45.900 -28.100 74.000 QUASIPEAK

6 12.443 10.068 38.330 48.398 -25.602 74.000 QUASIPEAK

Note:





Page: 75 of 217

Site : SR_1 Time : 2010/12/29 - 00:49




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.189 10.037 45.000 55.037 -17.849 72.886 AVERAGE

2 0.388 10.000 40.060 50.060 -17.140 67.200 AVERAGE

3 * 0.748 9.990 51.150 61.140 -2.860 64.000 AVERAGE

4 1.490 9.990 41.840 51.830 -12.170 64.000 AVERAGE

5 3.423 9.990 27.070 37.060 -26.940 64.000 AVERAGE

6 12.443 10.068 26.280 36.348 -27.652 64.000 AVERAGE

Note:





Page: 76 of 217

Site : SR_1 Time : 2010/12/29 - 00:41





Page: 77 of 217

Site : SR_1 Time : 2010/12/29 - 00:42




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.189 10.037 52.810 62.847 -20.039 82.886 QUASIPEAK

2 0.388 10.000 45.090 55.090 -22.110 77.200 QUASIPEAK

3 * 0.748 9.990 52.890 62.880 -11.120 74.000 QUASIPEAK

4 1.498 9.990 48.490 58.480 -15.520 74.000 QUASIPEAK

5 1.865 10.000 44.210 54.210 -19.790 74.000 QUASIPEAK

6 16.228 10.130 46.630 56.760 -17.240 74.000 QUASIPEAK

Note:





Page: 78 of 217

Site : SR_1 Time : 2010/12/29 - 00:42




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.189 10.037 44.470 54.507 -18.379 72.886 AVERAGE

2 0.388 10.000 38.850 48.850 -18.350 67.200 AVERAGE

3 * 0.748 9.990 51.210 61.200 -2.800 64.000 AVERAGE

4 1.498 9.990 44.680 54.670 -9.330 64.000 AVERAGE

5 1.865 10.000 37.370 47.370 -16.630 64.000 AVERAGE

6 16.228 10.130 44.410 54.540 -9.460 64.000 AVERAGE

Note:





Page: 79 of 217

Site : SR_1 Time : 2010/12/29 - 00:38





Page: 80 of 217

Site : SR_1 Time : 2010/12/29 - 00:40




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.197 10.239 50.150 60.389 -22.268 82.657 QUASIPEAK

2 0.396 10.188 44.330 54.518 -22.453 76.971 QUASIPEAK

3 * 0.748 10.140 53.030 63.170 -10.830 74.000 QUASIPEAK

4 1.505 10.090 46.750 56.840 -17.160 74.000 QUASIPEAK

5 1.869 10.074 47.650 57.724 -16.276 74.000 QUASIPEAK

6 2.244 10.070 48.310 58.380 -15.620 74.000 QUASIPEAK

Note:





Page: 81 of 217

Site : SR_1 Time : 2010/12/29 - 00:40




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.197 10.239 45.000 55.239 -17.418 72.657 AVERAGE

2 0.396 10.188 37.450 47.638 -19.333 66.971 AVERAGE

3 * 0.748 10.140 51.080 61.220 -2.780 64.000 AVERAGE

4 1.505 10.090 39.420 49.510 -14.490 64.000 AVERAGE

5 1.869 10.074 42.070 52.144 -11.856 64.000 AVERAGE

6 2.244 10.070 42.670 52.740 -11.260 64.000 AVERAGE

Note:





Page: 82 of 217

Site : SR_1 Time : 2010/12/23 - 04:58





Page: 83 of 217

Site : SR_1 Time : 2010/12/23 - 04:59




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.748 9.990 40.710 50.700 -23.300 74.000 QUASIPEAK

2 1.502 9.990 36.110 46.100 -27.900 74.000 QUASIPEAK

3 4.998 9.980 40.690 50.670 -23.330 74.000 QUASIPEAK

4 * 7.498 9.970 48.330 58.300 -15.700 74.000 QUASIPEAK

5 8.752 9.968 45.870 55.838 -18.162 74.000 QUASIPEAK

6 12.502 10.073 47.210 57.283 -16.717 74.000 QUASIPEAK

Note:





Page: 84 of 217

Site : SR_1 Time : 2010/12/23 - 04:59




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 * 0.748 9.990 39.420 49.410 -14.590 64.000 AVERAGE

2 1.502 9.990 30.200 40.190 -23.810 64.000 AVERAGE

3 4.998 9.980 30.460 40.440 -23.560 64.000 AVERAGE

4 7.498 9.970 36.180 46.150 -17.850 64.000 AVERAGE

5 8.752 9.968 33.980 43.948 -20.052 64.000 AVERAGE

6 12.502 10.073 34.740 44.813 -19.187 64.000 AVERAGE

Note:





Page: 85 of 217

Site : SR_1 Time : 2010/12/23 - 04:55





Page: 86 of 217

Site : SR_1 Time : 2010/12/23 - 04:56




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.392 10.000 36.850 46.850 -30.236 77.086 QUASIPEAK

2 0.748 9.990 41.030 51.020 -22.980 74.000 QUASIPEAK

3 1.498 9.990 37.750 47.740 -26.260 74.000 QUASIPEAK

4 5.908 9.980 40.650 50.630 -23.370 74.000 QUASIPEAK

5 * 16.166 10.130 45.110 55.240 -18.760 74.000 QUASIPEAK

6 23.127 10.100 44.930 55.030 -18.970 74.000 QUASIPEAK

Note:





Page: 87 of 217

Site : SR_1 Time : 2010/12/23 - 04:56




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.392 10.000 36.570 46.570 -20.516 67.086 AVERAGE

2 0.748 9.990 39.360 49.350 -14.650 64.000 AVERAGE

3 1.498 9.990 33.210 43.200 -20.800 64.000 AVERAGE

4 5.908 9.980 37.220 47.200 -16.800 64.000 AVERAGE

5 16.166 10.130 42.020 52.150 -11.850 64.000 AVERAGE

6 * 23.127 10.100 43.620 53.720 -10.280 64.000 AVERAGE

Note:





Page: 88 of 217

Site : SR_1 Time : 2010/12/23 - 04:49





Page: 89 of 217

Site : SR_1 Time : 2010/12/23 - 04:50




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.392 10.189 38.350 48.539 -28.547 77.086 QUASIPEAK

2 * 0.748 10.140 40.610 50.750 -23.250 74.000 QUASIPEAK

3 1.494 10.090 39.690 49.780 -24.220 74.000 QUASIPEAK

4 4.338 10.050 38.610 48.660 -25.340 74.000 QUASIPEAK

5 9.017 10.070 34.310 44.380 -29.620 74.000 QUASIPEAK

6 15.783 10.280 36.610 46.890 -27.110 74.000 QUASIPEAK

Note:





Page: 90 of 217

Site : SR_1 Time : 2010/12/23 - 04:50




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.392 10.189 37.370 47.559 -19.527 67.086 AVERAGE

2 * 0.748 10.140 39.540 49.680 -14.320 64.000 AVERAGE

3 1.494 10.090 36.730 46.820 -17.180 64.000 AVERAGE

4 4.338 10.050 27.680 37.730 -26.270 64.000 AVERAGE

5 9.017 10.070 25.630 35.700 -28.300 64.000 AVERAGE

6 15.783 10.280 26.140 36.420 -27.580 64.000 AVERAGE

Note:





Page: 91 of 217


Description : Front View of ISN Test

Test Mode : Mode 1

Description : Back View of ISN Test


Page: 92 of 217

Test Mode : Mode 2


Test Mode : Mode 2



Page: 93 of 217

Test Mode : Mode 3


Test Mode : Mode 3



Page: 94 of 217

Test Mode : Mode 4


Test Mode : Mode 4



Page: 95 of 217

5. Radiated Emission


According to EMC Standard : EN 55022

5.2. Test Setup

Under 1GHz Test Setup:

Above 1GHz Test Setup:


Page: 96 of 217

5.3. Limit

Limits

Frequency

(MHz) Distance (m) dBuV/m

30 – 230 10 30

230 – 1000 10 37

Limits

Frequency

(GHz)

Distance

(m)

Peak

(dBuV/m)

Average

(dBuV/m)

1 – 3 3 70 50

3 – 6 3 74 54

Remark:

1. The tighter limit shall apply at the edge between two frequency bands.

2. Distance refers to the distance in meters between the measuring instrument antenna

and the closed point of any part of the device or system.

Highest frequency generated or used

in the device or on which the device

operates or tunes (MHz)

Upper frequency of measurement

range (MHz)

Below 108 1000

108 – 500 2000

500 – 1000 5000

Above 1000 5th harmonic of the highest frequency

or 6 GHz, whichever is lower


Page: 97 of 217

5.4. Test Procedure

The EUT and its simulators are placed on a turn table which is 0.8 meter above ground. The

turn table can rotate 360 degrees to determine the position of the maximum emission level.

The EUT was positioned such that the distance from antenna to the EUT was 3/10 meters.

The antenna can move up and down between 1 meter and 4 meters to find out the maximum

emission level.

Both horizontal and vertical polarization of the antenna are set on measurement. In order to

find the maximum emission, all of the interface cables must be manipulated on radiated

measurement.

Radiated emissions were invested over the frequency range from 30MHz to1GHz using a

receiver bandwidth of 120kHz and above 1GHz using a receiver bandwidth of 1MHz.

30MHz to1GHz Radiated was performed at an antenna to EUT distance of 10 meters.

Above1GHz Radiated was performed at an antenna to EUT distance of 3 meters.

It is placed with absorb on the ground between EUT and Antenna.


No deviation.


Page: 98 of 217

5.6. Test Result Site : SITE5 Time : 2010/12/22 - 15:22


EUT : Notebook P.C. Probe : Site5_CBL6112_10M_0811 - HORIZONTAL


Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)

Detector Type

1 125.000 14.041 8.500 22.542 -7.458 30.000 QUASIPEAK

2 168.000 12.118 9.800 21.918 -8.082 30.000 QUASIPEAK

3 240.000 14.332 18.200 32.532 -4.468 37.000 QUASIPEAK

4 360.000 19.423 12.600 32.023 -4.977 37.000 QUASIPEAK

5 * 480.000 22.668 10.500 33.168 -3.832 37.000 QUASIPEAK

6 625.013 25.154 6.900 32.055 -4.945 37.000 QUASIPEAK

7 750.016 27.245 4.300 31.545 -5.455 37.000 QUASIPEAK

8 824.500 27.821 3.900 31.721 -5.279 37.000 QUASIPEAK

9 960.000 29.163 2.100 31.263 -5.737 37.000 QUASIPEAK

Note:

1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or

average measurements as necessary.




Page: 99 of 217

Site : SITE5 Time : 2010/12/22 - 11:34


EUT : Notebook P.C. Probe : Site5_CBL6112_10M_0811 - VERTICAL


Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)

Detector Type

1 125.000 14.041 9.600 23.642 -6.358 30.000 QUASIPEAK

2 176.630 11.623 11.900 23.523 -6.477 30.000 QUASIPEAK

3 240.000 14.332 17.300 31.632 -5.368 37.000 QUASIPEAK

4 360.000 19.423 10.600 30.023 -6.977 37.000 QUASIPEAK

5 480.000 22.668 10.200 32.868 -4.132 37.000 QUASIPEAK

6 625.000 25.154 5.900 31.054 -5.946 37.000 QUASIPEAK

7 750.017 27.245 3.800 31.045 -5.955 37.000 QUASIPEAK

8 * 875.000 28.260 5.000 33.261 -3.739 37.000 QUASIPEAK

9 960.000 29.163 2.600 31.763 -5.237 37.000 QUASIPEAK

Note:






Page: 100 of 217

Site : SITE5 Time : 2010/12/22 - 14:47




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)

Detector Type

1 125.000 14.041 9.500 23.542 -6.458 30.000 QUASIPEAK

2 168.000 12.118 7.600 19.718 -10.282 30.000 QUASIPEAK

3 227.000 12.681 13.300 25.981 -4.019 30.000 QUASIPEAK

4 240.000 14.332 17.100 31.432 -5.568 37.000 QUASIPEAK

5 360.000 19.423 12.200 31.623 -5.377 37.000 QUASIPEAK

6 463.500 22.212 8.800 31.012 -5.988 37.000 QUASIPEAK

7 * 480.000 22.668 10.900 33.568 -3.432 37.000 QUASIPEAK

8 618.000 25.087 7.600 32.687 -4.313 37.000 QUASIPEAK

9 750.000 27.245 5.100 32.345 -4.655 37.000 QUASIPEAK

10 820.000 27.774 3.600 31.374 -5.626 37.000 QUASIPEAK

11 960.000 29.163 2.800 31.963 -5.037 37.000 QUASIPEAK

Note:






Page: 101 of 217

Site : SITE5 Time : 2010/12/22 - 15:12




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)

Detector Type

1 67.950 6.918 12.600 19.518 -10.482 30.000 QUASIPEAK

2 125.000 14.041 9.700 23.742 -6.258 30.000 QUASIPEAK

3 155.200 12.511 11.300 23.811 -6.189 30.000 QUASIPEAK

4 240.000 14.332 16.900 31.232 -5.768 37.000 QUASIPEAK

5 360.000 19.423 10.250 29.673 -7.327 37.000 QUASIPEAK

6 480.000 22.668 9.200 31.868 -5.132 37.000 QUASIPEAK

7 624.976 25.154 5.600 30.754 -6.246 37.000 QUASIPEAK

8 772.500 27.237 4.300 31.537 -5.463 37.000 QUASIPEAK

9 * 875.021 28.261 5.100 33.361 -3.639 37.000 QUASIPEAK

10 960.000 29.163 2.200 31.363 -5.637 37.000 QUASIPEAK

Note:






Page: 102 of 217

Site : SITE5 Time : 2010/12/22 - 16:24




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)

Detector Type

1 120.000 13.895 8.100 21.995 -8.005 30.000 QUASIPEAK

2 168.000 12.118 8.900 21.018 -8.982 30.000 QUASIPEAK

3 240.000 14.332 17.500 31.832 -5.168 37.000 QUASIPEAK

4 360.000 19.423 11.900 31.323 -5.677 37.000 QUASIPEAK

5 480.000 22.668 10.200 32.868 -4.132 37.000 QUASIPEAK

6 625.000 25.154 5.300 30.454 -6.546 37.000 QUASIPEAK

7 875.000 28.260 4.300 32.561 -4.439 37.000 QUASIPEAK

8 960.000 29.163 3.800 32.963 -4.037 37.000 QUASIPEAK

9 * 1000.000 29.878 3.200 33.078 -3.922 37.000 QUASIPEAK

Note:






Page: 103 of 217

Site : SITE5 Time : 2010/12/22 - 16:43




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)

Detector Type

1 125.000 14.041 10.300 24.342 -5.658 30.000 QUASIPEAK

2 168.000 12.118 11.200 23.318 -6.682 30.000 QUASIPEAK

3 240.000 14.332 16.800 31.132 -5.868 37.000 QUASIPEAK

4 360.000 19.423 9.200 28.623 -8.377 37.000 QUASIPEAK

5 * 480.000 22.668 10.600 33.268 -3.732 37.000 QUASIPEAK

6 625.000 25.154 6.300 31.454 -5.546 37.000 QUASIPEAK

7 750.000 27.245 4.100 31.345 -5.655 37.000 QUASIPEAK

8 960.000 29.163 2.900 32.063 -4.937 37.000 QUASIPEAK

9 1000.000 29.878 3.300 33.178 -3.822 37.000 QUASIPEAK

Note:






Page: 104 of 217

Site : SITE5 Time : 2010/12/22 - 17:11




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)

Detector Type

1 125.000 14.041 8.900 22.942 -7.058 30.000 QUASIPEAK

2 154.500 12.536 9.200 21.736 -8.264 30.000 QUASIPEAK

3 240.000 14.332 16.500 30.832 -6.168 37.000 QUASIPEAK

4 360.000 19.423 11.300 30.723 -6.277 37.000 QUASIPEAK

5 463.500 22.212 8.200 30.412 -6.588 37.000 QUASIPEAK

6 480.000 22.668 9.100 31.768 -5.232 37.000 QUASIPEAK

7 625.000 25.154 6.300 31.454 -5.546 37.000 QUASIPEAK

8 750.000 27.245 5.100 32.345 -4.655 37.000 QUASIPEAK

9 772.500 27.237 5.500 32.737 -4.263 37.000 QUASIPEAK

10 960.000 29.163 2.900 32.063 -4.937 37.000 QUASIPEAK

11 * 1000.000 29.878 3.800 33.678 -3.322 37.000 QUASIPEAK

Note:






Page: 105 of 217

Site : SITE5 Time : 2010/12/22 - 17:27




Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)

Detector Type

1 61.090 6.809 12.500 19.309 -10.691 30.000 QUASIPEAK

2 120.000 13.895 9.100 22.995 -7.005 30.000 QUASIPEAK

3 154.500 12.536 11.500 24.036 -5.964 30.000 QUASIPEAK

4 240.000 14.332 17.700 32.032 -4.968 37.000 QUASIPEAK

5 360.000 19.423 10.700 30.123 -6.877 37.000 QUASIPEAK

6 * 480.000 22.668 10.200 32.868 -4.132 37.000 QUASIPEAK

7 500.000 23.073 6.300 29.373 -7.627 37.000 QUASIPEAK

8 625.000 25.154 6.300 31.454 -5.546 37.000 QUASIPEAK

9 750.000 27.245 5.200 32.445 -4.555 37.000 QUASIPEAK

10 772.500 27.237 4.100 31.337 -5.663 37.000 QUASIPEAK

11 960.000 29.163 2.600 31.763 -5.237 37.000 QUASIPEAK


Page: 106 of 217

Site : CB7 (9x6x6_Chamber) Time : 2010/12/21 - 20:01

Limit : CISPR_22_B_(Above_1G)_03M_PK Margin : 6

EUT : Notebook P.C. Probe : 9120D_1-18G_Horn - HORIZONTAL


Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)

Detector Type

1 1577.000 -4.979 56.130 51.151 -18.849 70.000 PEAK

2 * 2664.000 -0.857 56.810 55.953 -14.047 70.000 PEAK

Note:






Page: 107 of 217


Limit : CISPR_22_B_(Above_1G)_03M_AV Margin : 6



Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)

Detector Type

1 1577.000 -4.979 41.380 36.401 -13.599 50.000 AVERAGE

2 * 2664.000 -0.857 41.270 40.413 -9.587 50.000 AVERAGE

Note:






Page: 108 of 217



EUT : Notebook P.C. Probe : 9120D_1-18G_Horn - VERTICAL


Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)

Detector Type

1 1995.000 -2.016 61.110 59.095 -10.905 70.000 PEAK

2 * 2664.000 -0.857 65.370 64.513 -5.487 70.000 PEAK

Note:






Page: 109 of 217





Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)

Detector Type

1 1995.000 -2.016 45.030 43.015 -6.985 50.000 AVERAGE

2 * 2664.000 -0.857 43.890 43.033 -6.967 50.000 AVERAGE

Note:






Page: 110 of 217





Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)

Detector Type

1 1788.000 -3.612 56.130 52.518 -17.482 70.000 PEAK

2 * 1995.000 -2.016 56.030 54.015 -15.985 70.000 PEAK

Note:






Page: 111 of 217





Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)

Detector Type

1 1788.000 -3.612 41.330 37.718 -12.282 50.000 AVERAGE

2 * 1995.000 -2.016 42.130 40.115 -9.885 50.000 AVERAGE

Note:






Page: 112 of 217





Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)

Detector Type

1 1995.000 -2.016 61.330 59.315 -10.685 70.000 PEAK

2 * 2666.000 -0.850 61.590 60.740 -9.260 70.000 PEAK

Note:






Page: 113 of 217





Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)

Detector Type

1 1995.000 -2.016 38.330 36.315 -13.685 50.000 AVERAGE

2 * 2666.000 -0.850 44.390 43.540 -6.460 50.000 AVERAGE

Note:






Page: 114 of 217





Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)

Detector Type

1 2000.000 -1.985 60.890 58.904 -11.096 70.000 PEAK

2 * 2997.000 -0.398 60.170 59.771 -10.229 70.000 PEAK

Note:






Page: 115 of 217





Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)

Detector Type

1 2000.000 -1.985 41.890 39.904 -10.096 50.000 AVERAGE

2 * 2997.000 -0.398 42.180 41.781 -8.219 50.000 AVERAGE

Note:






Page: 116 of 217





Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)

Detector Type

1 1495.000 -5.433 61.340 55.907 -14.093 70.000 PEAK

2 * 1995.000 -2.016 60.890 58.875 -11.125 70.000 PEAK

Note:






Page: 117 of 217





Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)

Detector Type

1 1495.000 -5.433 43.110 37.677 -12.323 50.000 AVERAGE

2 * 1995.000 -2.016 42.740 40.725 -9.275 50.000 AVERAGE

Note:






Page: 118 of 217





Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)

Detector Type

1 1257.000 -6.616 60.050 53.434 -16.566 70.000 PEAK

2 * 2005.000 -1.986 59.430 57.444 -12.556 70.000 PEAK

Note:






Page: 119 of 217





Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)

Detector Type

1 1257.000 -6.616 48.990 42.374 -7.626 50.000 AVERAGE

2 * 2005.000 -1.986 46.350 44.364 -5.636 50.000 AVERAGE

Note:






Page: 120 of 217





Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)

Detector Type

1 1605.000 -5.046 59.330 54.284 -15.716 70.000 PEAK

2 * 1995.000 -2.016 62.680 60.665 -9.335 70.000 PEAK

Note:






Page: 121 of 217





Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)

Detector Type

1 * 1605.000 -5.046 46.180 41.134 -8.866 50.000 AVERAGE

2 1995.000 -2.016 42.870 40.855 -9.145 50.000 AVERAGE

Note:






Page: 122 of 217


Description : Front View of Radiated Test

Test Mode : Mode 1

Description : Back View of Radiated Test


Page: 123 of 217

Test Mode : Mode 1

Description : Front View of High Frequency Radiated Test

Test Mode : Mode 2



Page: 124 of 217

Test Mode : Mode 2


Test Mode : Mode 2



Page: 125 of 217

Test Mode : Mode 3


Test Mode : Mode 3



Page: 126 of 217

Test Mode : Mode 3


Test Mode : Mode 4



Page: 127 of 217

Test Mode : Mode 4


Test Mode : Mode 4



Page: 128 of 217

6. Harmonic Current Emission


According to EMC Standard : EN 61000-3-2

6.2. Test Setup

6.3. Limit

(a) Limits of Class A Harmonics Currents

Harmonics

Order

n

Maximum Permissible

harmonic current

A

Harmonics

Order

n

Maximum Permissible

harmonic current

A

Odd harmonics Even harmonics

3 2.30 2 1.08

5 1.14 4 0.43

7 0.77 6 0.30

9 0.40 8 n 40 0.23 * 8/n

11 0.33

13 0.21

15 n 39 0.15 * 15/n


Page: 129 of 217

(b) Limits of Class B Harmonics Currents

For Class B equipment, the harmonic of the input current shall not exceed the maximum

permissible values given in table that is the limit of Class A multiplied by a factor of 1.5.

(c) Limits of Class C Harmonics Currents

Harmonics Order

n

Maximum Permissible harmonic current

Expressed as a percentage of the input

current at the fundamental frequency

％

2 2

3 30．λ＊

5 10

7 7

9 5

11 n 39

(odd harmonics only) 3

＊λ is the circuit power factor

(d) Limits of Class D Harmonics Currents

Harmonics Order

n

Maximum Permissible

harmonic current per watt

mA/W

Maximum Permissible

harmonic current

A

3 3.4 2.30

5 1.9 1.14

7 1.0 0.77

9 0.5 0.40

11 0.35 0.33

11 n 39

(odd harmonics only) 3.85/n See limit of Class A


Page: 130 of 217

6.4. Test Procedure

The EUT is supplied in series with power analyzer from a power source having the same

normal voltage and frequency as the rated supply voltage and the equipment under test.

And the rated voltage at the supply voltage of EUT of 0.94 times and 1.06 times shall be

performed.


No deviation.


Page: 131 of 217

6.6. Test Result Product Notebook PC

Test Item Power Harmonics

Test Mode Mode 1

Date of Test 2010/12/31 Test Site No.3 Shielded Room

Test Result: Pass Source qualification: Normal

Current & voltage waveforms

-1.5

-1.0

-0.5

0.0

0.5

1.0

1.5

-300

-200

-100

0

100

200

300

Cu

rre

nt (A

mp

s)

Vo

ltag

e (V

olts)

Harmonics and Class D limit line European Limits

0.000.050.100.150.200.250.300.350.40

Cu

rre

nt R

MS

(Am

ps)

Harmonic #4 8 12 16 20 24 28 32 36 40

Test result: Pass Worst harmonic was #3 with 56.54% of the limit.


Page: 132 of 217

Test Result: Pass Source qualification: Normal THC(A): 0.16 I-THD(%): 45.66 POHC(A): 0.002 POHC Limit(A): 0.036 Highest parameter values during test:

V_RMS (Volts): 229.57 Frequency(Hz): 50.00 I_Peak (Amps): 0.995 I_RMS (Amps): 0.425 I_Fund (Amps): 0.362 Crest Factor: 2.488 Power (Watts): 82.7 Power Factor: 0.847

Harm# Harms(avg) 100%Limit %of Limit Harms(max) 150%Limit %of Limit Status 2 0.003 3 0.159 0.281 56.5 0.158 0.422 39.26 Pass 4 0.001 5 0.012 0.157 7.9 0.014 0.236 6.24 Pass 6 0.001 7 0.009 0.083 11.5 0.008 0.124 8.91 Pass 8 0.001 9 0.006 0.041 15.1 0.008 0.062 12.18 Pass 10 0.001 11 0.001 0.029 4.9 0.003 0.043 6.42 Pass 12 0.001 13 0.002 0.025 10.0 0.003 0.037 9.48 Pass 14 0.001 15 0.001 0.022 5.7 0.002 0.032 6.27 Pass 16 0.000 17 0.001 0.019 5.7 0.001 0.028 6.71 Pass 18 0.000 19 0.002 0.017 9.6 0.002 0.025 9.06 Pass 20 0.000 21 0.001 0.015 8.1 0.001 0.023 9.12 Pass 22 0.000 23 0.001 0.014 5.7 0.001 0.021 5.88 Pass 24 0.000 25 0.001 0.013 7.1 0.001 0.019 6.36 Pass 26 0.000 27 0.001 0.012 6.1 0.001 0.018 6.86 Pass 28 0.000 29 0.001 0.011 5.5 0.001 0.016 6.56 Pass 30 0.000 31 0.001 0.010 7.2 0.001 0.015 7.31 Pass 32 0.000 33 0.000 0.010 3.6 0.000 0.014 4.45 Pass 34 0.000 35 0.001 0.009 5.6 0.001 0.014 5.27 Pass 36 0.000 37 0.000 0.009 5.3 0.000 0.013 6.35 Pass 38 0.000 39 0.000 0.008 4.8 0.000 0.012 5.32 Pass 40 0.000

1.Dynamic limits were applied for this test. The highest harmonics values in the above table may not occur at the

same window as the maximum harmonics/limit ratio.

2:According to EN61000-3-2 paragraph 7 the note 1 and 2 are valid for all applications having an active input power

>75W. Others the result should be pass.


Page: 133 of 217

Product Notebook PC


Test Mode Mode 2




-1.5

-1.0

-0.5

0.0

0.5

1.0

1.5

-300

-200

-100

0

100

200

300

Cu

rre

nt (A

mp

s)

Vo

ltag

e (V

olts)


0.000.050.100.150.200.250.300.350.400.45

Cu

rre

nt R

MS

(Am

ps)

Harmonic #4 8 12 16 20 24 28 32 36 40



Page: 134 of 217









Page: 135 of 217

Product Notebook PC


Test Mode Mode 3




-3

-2

-1

0

1

2

3

-300

-200

-100

0

100

200

300

Cu

rre

nt (A

mp

s)

Vo

ltag

e (V

olts)


0.0000.0250.0500.0750.1000.1250.1500.1750.200

Cu

rre

nt R

MS

(Am

ps)

Harmonic #4 8 12 16 20 24 28 32 36 40



Page: 136 of 217









Page: 137 of 217

Product Notebook PC


Test Mode Mode 4




-3

-2

-1

0

1

2

3

-300

-200

-100

0

100

200

300

Cu

rre

nt (A

mp

s)

Vo

ltag

e (V

olts)


0.00

0.05

0.10

0.15

0.20

0.25

0.30

Cu

rre

nt R

MS

(Am

ps)

Harmonic #4 8 12 16 20 24 28 32 36 40



Page: 138 of 217









Page: 139 of 217


Description : Power Harmonics Test Setup

Test Mode : Mode 2



Page: 140 of 217

Test Mode : Mode 3


Test Mode : Mode 4



Page: 141 of 217

7. Voltage Fluctuation and Flicker


According to EMC Standard : EN 61000-3-3

7.2. Test Setup

7.3. Limit

The following limits apply:

－ the value of Pst shall not be greater than 1.0;

－ the value of Plt shall not be greater than 0.65;

－ the value of d(t) during a voltage change shall not exceed 3.3 ％ for more than 500

ms;

－ the relative steady-state voltage change, dc, shall not exceed 3.3 ％;

－ the maximum relative voltage change, dmax, shall not exceed;

a) 4 ％ without additional conditions;

b) 6 ％ for equipment which is:

－ switched manually, or

－ switched automatically more frequently than twice per day, and also has either a

delayed restart (the delay being not less than a few tens of seconds), or manual restart,

after a power supply interruption.

NOTE The cycling frequency will be further limited by the Pst and P1t limit.

For example: a dmax of 6％producing a rectangular voltage change characteristic twice per

hour will give a P1t of about 0.65.


Page: 142 of 217

c) 7 ％ for equipment which is:

－ attended whilst in use (for example: hair dryers, vacuum cleaners, kitchen equipment

such as mixers, garden equipment such as lawn mowers, portable tools such as

electric drills), or

－ switched on automatically, or is intended to be switched on manually, no more than

twice per day, and also has either a delayed restart (the delay being not less than a

few tens of seconds) or manual restart, after a power supply interruption.

Pst and P1t requirements shall not be applied to voltage changes caused by manual switching.

7.4. Test Procedure

The EUT is supplied in series with power analyzer from a power source having the same

normal voltage and frequency as the rated supply voltage and the equipment under test.

And the rated voltage at the supply voltage of EUT of 0.94 times and 1.06 times shall be

performed.


No deviation.


Page: 143 of 217


Test Item Voltage Fluctuation and Flicker

Test Mode Mode 1


Test Result: Pass Status: Test Completed

Psti and limit line European Limits

0.25

0.50

0.75

1.00

Pst

10:5

9:4

7

Plt and limit line

0.00

0.25

0.50

Plt

10:5

9:4

7

Parameter values recorded during the test: Vrms at the end of test (Volt): 229.42 Highest dt (%): 0.00 Test limit (%): 3.30 Pass Time(mS) > dt: 0.0 Test limit (mS): 500.0 Pass Highest dc (%): 0.00 Test limit (%): 3.30 Pass Highest dmax (%): 0.00 Test limit (%): 4.00 Pass Highest Pst (10 min. period): 0.064 Test limit: 1.000 Pass Highest Plt (2 hr. period): 0.028 Test limit: 0.650 Pass


Page: 144 of 217

Product Notebook PC


Test Mode Mode 2




0.25

0.50

0.75

1.00

Pst

11:2

1:0

3

Plt and limit line

0.00

0.25

0.50

Plt

11:2

1:0

3



Page: 145 of 217

Product Notebook PC


Test Mode Mode 3




0.25

0.50

0.75

1.00

Pst

12:0

0:2

0

Plt and limit line

0.00

0.25

0.50

Plt

12:0

0:2

0



Page: 146 of 217

Product Notebook PC


Test Mode Mode 4




0.25

0.50

0.75

1.00

Pst

13:3

7:0

2

Plt and limit line

0.00

0.25

0.50

Plt

13:3

7:0

2



Page: 147 of 217

7.7. Test Photograph

Test Mode : Mode 1

Description : Flicker Test Setup

Test Mode : Mode 2



Page: 148 of 217

Test Mode : Mode 3


Test Mode : Mode 4



Page: 149 of 217

8. Electrostatic Discharge


According to Standard: IEC 61000-4-2

8.2. Test Setup

8.3. Limit

Item Environmental

Phenomena

Units Test Specification Performance

Criteria

Enclosure Port

Electrostatic Discharge kV(Charge Voltage) ±8 Air Discharge

±4 Contact Discharge B


Page: 150 of 217

8.4. Test Procedure

Direct application of discharges to the EUT:

Contact discharge was applied only to conductive surfaces of the EUT.

Air discharges were applied only to non-conductive surfaces of the EUT.

During the test, it was performed with single discharges. For the single discharge

time between successive single discharges will be keep longer 1 second. It was at

least ten single discharges with positive and negative at the same selected point.

The selected point, which was performed with electrostatic discharge, was marked

on the red label of the EUT.

Indirect application of discharges to the EUT:

Vertical Coupling Plane (VCP):

The coupling plane, of dimensions 0.5m x 0.5m, is placed parallel to, and positioned

at a distance 0.1m from, the EUT, with the Discharge Electrode touching the

coupling plane.

The four faces of the EUT will be performed with electrostatic discharge. It was at


Horizontal Coupling Plane (HCP):

The coupling plane is placed under to the EUT. The generator shall be positioned

vertically at a distance of 0.1m from the EUT, with the Discharge Electrode touching

the coupling plane.

The four faces of the EUT will be performed with electrostatic discharge. It was at



No deviation.


Page: 151 of 217


Test Item Electrostatic Discharge

Test Mode Mode 1


Item Amount of

Discharge Voltage

Required

Criteria

Complied To

Criteria (A,B,C) Results

Air Discharge 10

10

+8kV

-8kV

B

B

B

B

Pass

Pass

Contact Discharge 25

25

+4kV

-4kV

B

B

B

B

Pass

Pass

Indirect Discharge

(HCP)

25

25

+4kV

-4kV

B

B

A

A

Pass

Pass

Indirect Discharge

(VCP Front)

25

25

+4kV

-4kV

B

B

A

A

Pass

Pass

Indirect Discharge

(VCP Left)

25

25

+4kV

-4kV

B

B

A

A

Pass

Pass

Indirect Discharge

(VCP Back)

25

25

+4kV

-4kV

B

B

A

A

Pass

Pass

Indirect Discharge

(VCP Right)

25

25

+4kV

-4kV

B

B

A

A

Pass

Pass

Note:

The testing performed is from lowest level up to the highest level as required by standard, but only

highest level is shown on the report.

NR: No Requirement Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information

EUT stopped operation and could / could not be reset by operator at kV. No false alarms or other malfunctions were observed during or after the test.

Remark:

The Contact discharges were applied at least total 200 discharges at a minimum of four test points.


Page: 152 of 217

Product Notebook PC


Test Mode Mode 2


Item Amount of

Discharge Voltage

Required

Criteria

Complied To


Air Discharge 10

10

+8kV

-8kV

B

B

B

B

Pass

Pass


25

+4kV

-4kV

B

B

B

B

Pass

Pass

Indirect Discharge

(HCP)

25

25

+4kV

-4kV

B

B

A

A

Pass

Pass

Indirect Discharge

(VCP Front)

25

25

+4kV

-4kV

B

B

A

A

Pass

Pass

Indirect Discharge

(VCP Left)

25

25

+4kV

-4kV

B

B

A

A

Pass

Pass

Indirect Discharge

(VCP Back)

25

25

+4kV

-4kV

B

B

A

A

Pass

Pass

Indirect Discharge

(VCP Right)

25

25

+4kV

-4kV

B

B

A

A

Pass

Pass

Note:





Remark:



Page: 153 of 217

Product Notebook PC


Test Mode Mode 3


Item Amount of

Discharge Voltage

Required

Criteria

Complied To


Air Discharge 10

10

+8kV

-8kV

B

B

B

B

Pass

Pass


25

+4kV

-4kV

B

B

B

B

Pass

Pass

Indirect Discharge

(HCP)

25

25

+4kV

-4kV

B

B

A

A

Pass

Pass

Indirect Discharge

(VCP Front)

25

25

+4kV

-4kV

B

B

A

A

Pass

Pass

Indirect Discharge

(VCP Left)

25

25

+4kV

-4kV

B

B

A

A

Pass

Pass

Indirect Discharge

(VCP Back)

25

25

+4kV

-4kV

B

B

A

A

Pass

Pass

Indirect Discharge

(VCP Right)

25

25

+4kV

-4kV

B

B

A

A

Pass

Pass

Note:





Remark:



Page: 154 of 217

Product Notebook PC


Test Mode Mode 4


Item Amount of

Discharge Voltage

Required

Criteria

Complied To


Air Discharge 10

10

+8kV

-8kV

B

B

B

B

Pass

Pass


25

+4kV

-4kV

B

B

B

B

Pass

Pass

Indirect Discharge

(HCP)

25

25

+4kV

-4kV

B

B

A

A

Pass

Pass

Indirect Discharge

(VCP Front)

25

25

+4kV

-4kV

B

B

A

A

Pass

Pass

Indirect Discharge

(VCP Left)

25

25

+4kV

-4kV

B

B

A

A

Pass

Pass

Indirect Discharge

(VCP Back)

25

25

+4kV

-4kV

B

B

A

A

Pass

Pass

Indirect Discharge

(VCP Right)

25

25

+4kV

-4kV

B

B

A

A

Pass

Pass

Note:





Remark:



Page: 155 of 217


Test Mode : Mode 1

Description : ESD Test Setup

Test Mode : Mode 2



Page: 156 of 217

Test Mode : Mode 3


Test Mode : Mode 4



Page: 157 of 217

9. Radiated Susceptibility



9.2. Test Setup

9.3. Limit

Item Environmental

Phenomena

Units Test

Specification

Performance

Criteria

Enclosure Port

Radio-Frequency

Electromagnetic Field

Amplitude Modulated

MHz

V/m(Un-modulated, rms)

% AM (1kHz)

80-1000

3

80

A


Page: 158 of 217

9.4. Test Procedure

The EUT and load, which are placed on a table that is 0.8 meter above ground, are

placed with one coincident with the calibration plane such that the distance from

antenna to the EUT was 3 meters.

Both horizontal and vertical polarization of the antenna and four sides of the EUT are set

on measurement.

In order to judge the EUT performance, a CCD Notebook PCis used to monitor EUT

screen.

All the scanning conditions are as follows:

Condition of Test Remarks

1. Field Strength 3 V/m Level 2

2. Radiated Signal AM 80% Modulated with 1kHz

3. Scanning Frequency 80MHz - 1000MHz

4 Dwell Time 3 Seconds

5. Frequency step size f : 1%

6. The rate of Swept of Frequency 1.5 x 10-3 decades/s


No deviation.


Page: 159 of 217


Test Item Radiated susceptibility

Test Mode Mode 1

Date of Test 2011/01/05 Test Site Chamber5

Frequency

(MHz)

Position

(Angle) Polarity

(H or V)

Field

Strength

(V/m)

Required

Criteria

Complied To

Criteria

(A,B,C)

Results

80-1000 FRONT H 3 A A PASS

80-1000 FRONT V 3 A A PASS

80-1000 BACK H 3 A A PASS

80-1000 BACK V 3 A A PASS

80-1000 RIGHT H 3 A A PASS

80-1000 RIGHT V 3 A A PASS

80-1000 LEFT H 3 A A PASS

80-1000 LEFT V 3 A A PASS

80-1000 UP H 3 A A PASS

80-1000 UP V 3 A A PASS

80-1000 DOWN H 3 A A PASS

80-1000 DOWN V 3 A A PASS

Note:

The testing performed is from lowest level up to the highest level as required by standard, but

only highest level is shown on the report.

Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information

There was no observable degradation in performance. EUT stopped operation and could / could not be reset by operator at V/m

at frequency MHz.

No false alarms or other malfunctions were observed during or after the test.


Page: 160 of 217

Product Notebook PC


Test Mode Mode 2


Frequency

(MHz)

Position

(Angle) Polarity

(H or V)

Field

Strength

(V/m)

Required

Criteria

Complied To

Criteria

(A,B,C)

Results









80-1000 UP H 3 A A PASS

80-1000 UP V 3 A A PASS



Note:





at frequency MHz.



Page: 161 of 217

Product Notebook PC


Test Mode Mode 3


Frequency

(MHz)

Position

(Angle) Polarity

(H or V)

Field

Strength

(V/m)

Required

Criteria

Complied To

Criteria

(A,B,C)

Results









80-1000 UP H 3 A A PASS

80-1000 UP V 3 A A PASS



Note:





at frequency MHz.



Page: 162 of 217

Product Notebook PC


Test Mode Mode 4


Frequency

(MHz)

Position

(Angle) Polarity

(H or V)

Field

Strength

(V/m)

Required

Criteria

Complied To

Criteria

(A,B,C)

Results









80-1000 UP H 3 A A PASS

80-1000 UP V 3 A A PASS



Note:





at frequency MHz.



Page: 163 of 217


Description : Radiated Susceptibility Test Setup

Test Mode : Mode 2



Page: 164 of 217

Test Mode : Mode 3


Test Mode : Mode 4



Page: 165 of 217

10. Electrical Fast Transient/Burst


According to Standard : IEC 61000-4-4

10.2. Test Setup

10.3. Limit

Item Environmental Phenomena

Units Test Specification Performance Criteria

I/O and communication ports Fast Transients Common Mode

kV (Peak) Tr/Th ns Rep. Frequency kHz

+0.5 5/50 5

B

Input DC Power Ports Fast Transients Common Mode


+0.5 5/50 5

B

Input AC Power Ports Fast Transients Common Mode


+1 5/50 5

B


Page: 166 of 217

10.4. Test Procedure

The EUT is placed on a table that is 0.8 meter height. A ground reference plane is placed on

the table, and uses a 0.1m insulation between the EUT and ground reference plane.

The minimum area of the ground reference plane is 1m*1m, and 0.65mm thick min, and

projected beyond the EUT by at least 0.1m on all sides.

Test on I/O and communication ports:

The EFT interference signal is through a coupling clamp device couples to the signal and

control lines of the EUT with burst noise for 1minute.

Test on power supply ports:

The EUT is connected to the power mains through a coupling device that directly couples the

EFT/B interference signal.

Each of the Line and Neutral conductors is impressed with burst noise for 1 minute.

The length of the signal and power lines between the coupling device and the EUT is 0.5m.


No deviation.


Page: 167 of 217


Test Item Electrical fast transient/burst

Test Mode Mode 1


Inject

Line Polarity

Voltage

kV

Inject

Time

(Second)

Inject

Method

Required

Criteria

Complied

to

Criteria Result

L-N-PE ± 1kV 60 Direct B A PASS

LAN ± 0.5kV 60 Clamp B A PASS

Note:



Meet criteria A : Operate as intended during and after the test

Meet criteria B : Operate as intended after the test

Meet criteria C : Loss/Error of function

Additional Information

EUT stopped operation and could / could not be reset by operator at kV of

Line .



Page: 168 of 217

Product Notebook PC


Test Mode Mode 2


Inject

Line Polarity

Voltage

kV

Inject

Time

(Second)

Inject

Method

Required

Criteria

Complied

to

Criteria Result



Note:








Line .



Page: 169 of 217

Product Notebook PC


Test Mode Mode 3


Inject

Line Polarity

Voltage

kV

Inject

Time

(Second)

Inject

Method

Required

Criteria

Complied

to

Criteria Result



Note:








Line .



Page: 170 of 217

Product Notebook PC


Test Mode Mode 4


Inject

Line Polarity

Voltage

kV

Inject

Time

(Second)

Inject

Method

Required

Criteria

Complied

to

Criteria Result

L-N ± 1kV 60 Direct B A PASS


Note:








Line .



Page: 171 of 217


Test Mode : Mode 1

Description : EFT/B Test Setup

Test Mode : Mode 1

Description : EFT/B Test Setup - Clamp


Page: 172 of 217

Test Mode : Mode 2


Test Mode : Mode 2



Page: 173 of 217

Test Mode : Mode 3


Test Mode : Mode 3



Page: 174 of 217

Test Mode : Mode 4


Test Mode : Mode 4



Page: 175 of 217

11. Surge



11.2. Test Setup

11.3. Limit

Item Environmental Phenomena Units Test Specification Performance Criteria

Signal Ports and Telecommunication Ports(See 1) and 2) ) Surges Line to Ground

Tr/Th us kV

1.2/50 (8/20) 1

B

Input DC Power Ports Surges Line to Ground

Tr/Th us kV

1.2/50 (8/20) 0.5

B

AC Input and AC Output Power Ports Surges Line to Line Line to Ground

Tr/Th us kV kV

1.2/50 (8/20) 1 2

B

Notes:

1) Applicable only to ports which according to the manufacturer’s may directly to outdoor

cables.

2) Where normal functioning cannot be achieved because of the impact of the CDN on the

EUT, no immunity test shall be required.


Page: 176 of 217


The EUT and its load are placed on a table that is 0.8 meter above a metal ground plane

measured 1m*1m min. and 0.65mm thick min. And projected beyond the EUT by at least

0.1m on all sides. The length of power cord between the coupling device and the EUT shall

be 2m or less.

For Input and Output AC Power or DC Input and DC Output Power Ports:

The EUT is connected to the power mains through a coupling device that directly couples the

Surge interference signal.

The surge noise shall be applied synchronized to the voltage phase at 00, 900, 1800, 2700 and

the peak value of the a.c. voltage wave. (Positive and negative)

Each of Line-Earth and Line-Line is impressed with a sequence of five surge voltages with

interval of 1 min.


No deviation.


Page: 177 of 217


Test Item Surge

Test Mode Mode 1


Inject

Line Polarity Angle

Voltage

kV

Time

Interval

(Second)

Inject

Method

Required

Criteria

Complied

to

Criteria Result

L-N ± 0 1kV 60 Direct B A PASS




N-PE ± 0 2kV 60 Direct B A PASS




L-PE ± 0 2kV 60 Direct B A PASS




Note:



Meet criteria A : Operate as intended during and after the test Meet criteria B : Operate as intended after the test Meet criteria C : Loss/Error of function Additional Information

EUT stopped operation and could / could not be reset by operator at kV of Line .



Page: 178 of 217

Product Notebook PC

Test Item Surge

Test Mode Mode 2


Inject

Line Polarity Angle

Voltage

kV

Time

Interval

(Second)

Inject

Method

Required

Criteria

Complied

to

Criteria Result













Note:







Page: 179 of 217

Product Notebook PC

Test Item Surge

Test Mode Mode 3


Inject

Line Polarity Angle

Voltage

kV

Time

Interval

(Second)

Inject

Method

Required

Criteria

Complied

to

Criteria Result













Note:







Page: 180 of 217

Product Notebook PC

Test Item Surge

Test Mode Mode 4


Inject

Line Polarity Angle

Voltage

kV

Time

Interval

(Second)

Inject

Method

Required

Criteria

Complied

to

Criteria Result













Note:







Page: 181 of 217


Test Mode : Mode 1

Description : SURGE Test Setup

Test Mode : Mode 2



Page: 182 of 217

Test Mode : Mode 3


Test Mode : Mode 4



Page: 183 of 217

12. Conducted Susceptibility



12.2. Test Setup

CDN Test Mode

EM Clamp Test Mode


Page: 184 of 217

12.3. Limit

Item Environmental Phenomena Units Test Specification

Performance Criteria

Signal Ports and Telecommunication Ports Radio-Frequency Continuous Conducted

MHz V (rms, Un-modulated) % AM (1kHz)

0.15-80 3 80

A

Input DC Power Ports Radio-Frequency Continuous Conducted


0.15-80 3 80

A

Input AC Power Ports Radio-Frequency Continuous Conducted


0.15-80 3 80

A


The EUT are placed on a table that is 0.8 meter height, and a Ground reference plane on the table, EUT are placed upon table and use a 10cm insulation between the EUT and Ground reference plane. For Signal Ports and Telecommunication Ports The disturbance signal is through a coupling and decoupling networks (CDN) or EM-clamp device couples to the signal and Telecommunication lines of the EUT. For Input DC and AC Power Ports The EUT is connected to the power mains through a coupling and decoupling networks for power supply lines. And directly couples the disturbances signal into EUT. Used CDN-M2 for two wires or CDN-M3 for three wires. All the scanning conditions are as follows: Condition of Test Remarks 1. Field Strength 130dBuV(3V) Level 2 2. Radiated Signal AM 80% Modulated with 1kHz 3. Scanning Frequency 0.15MHz – 80MHz 4 Dwell Time 3 Seconds 5. Frequency step size f : 1% 6. The rate of Swept of Frequency 1.5 x 10-3 decades/s


No deviation.


Page: 185 of 217


Test Item Conducted susceptibility

Test Mode Mode 1


Frequency

Range

(MHz)

Voltage

Applied

dBuV(V)

Inject

Method

Tested Port

of

EUT

Required

Criteria

Performance

Criteria

Complied To

Result

0.15~80 130 (3V) CDN AC IN A A PASS

0.15~80 130 (3V) CDN LAN A A PASS

Note:







EUT stopped operation and could / could not be reset by operator at dBuV(V) at

frequency MHz.

No false alarms or other malfunctions were observed during or after the test. The

acceptance criteria were met, and the EUT passed the test.


Page: 186 of 217

Product Notebook PC


Test Mode Mode 2


Frequency

Range

(MHz)

Voltage

Applied

dBuV(V)

Inject

Method

Tested Port

of

EUT

Required

Criteria

Performance

Criteria

Complied To

Result


0.15~80 130 (3V) CDN LAN A A PASS

Note:








frequency MHz.




Page: 187 of 217

Product Notebook PC


Test Mode Mode 3


Frequency

Range

(MHz)

Voltage

Applied

dBuV(V)

Inject

Method

Tested Port

of

EUT

Required

Criteria

Performance

Criteria

Complied To

Result


0.15~80 130 (3V) CDN LAN A A PASS

Note:








frequency MHz.




Page: 188 of 217

Product Notebook PC


Test Mode Mode 4


Frequency

Range

(MHz)

Voltage

Applied

dBuV(V)

Inject

Method

Tested Port

of

EUT

Required

Criteria

Performance

Criteria

Complied To

Result


0.15~80 130 (3V) CDN LAN A A PASS

Note:








frequency MHz.




Page: 189 of 217


Test Mode : Mode 1

Description : Conducted Susceptibility Test Setup

Test Mode : Mode 1

Description : Conducted Susceptibility Test Setup - CDN


Page: 190 of 217

Test Mode : Mode 2


Test Mode : Mode 2



Page: 191 of 217

Test Mode : Mode 3


Test Mode : Mode 3



Page: 192 of 217

Test Mode : Mode 4


Test Mode : Mode 4



Page: 193 of 217

13. Power Frequency Magnetic Field



13.2. Test Setup

13.3. Limit

Item Environmental Phenomena

Units Test Specification Performance Criteria

Enclosure Port Power-Frequency

Magnetic Field Hz A/m (r.m.s.)

50 1

A


The EUT and its load are placed on a table which is 0.8 meter above a metal ground

plane measured at least 1m*1m min. The test magnetic field shall be placed at central

of the induction coil.

The test magnetic Field shall be applied 10 minutes by the immersion method to the EUT.

And the induction coil shall be rotated by 90 in order to expose the EUT to the test field

with different orientation (X, Y, Z Orientations).

13.5. Deviation from Test Standard No deviation.


Page: 194 of 217


Test Item Power frequency magnetic field

Test Mode Mode 1


Polarization Frequency

(Hz)

Magnetic

Strength

(A/m)

Required

Performance

Criteria

Performance

Criteria

Complied To

Test Result

X Orientation 50 1 A A PASS

Y Orientation 50 1 A A PASS

Z Orientation 50 1 A A PASS

Meet criteria A: Operate as intended during and after the test

Meet criteria B: Operate as intended after the test

Meet criteria C: Loss/Error of function


EUT stopped operation and could / could not be reset by operator at kV

of Line .

No false alarms or other malfunctions were observed during or after the test. The acceptance

criteria were met, and the EUT passed the test.


Page: 195 of 217

Product Notebook PC


Test Mode Mode 2



(Hz)

Magnetic

Strength

(A/m)

Required

Performance

Criteria

Performance

Criteria

Complied To

Test Result









of Line .




Page: 196 of 217

Product Notebook PC


Test Mode Mode 3



(Hz)

Magnetic

Strength

(A/m)

Required

Performance

Criteria

Performance

Criteria

Complied To

Test Result









of Line .




Page: 197 of 217

Product Notebook PC


Test Mode Mode 4



(Hz)

Magnetic

Strength

(A/m)

Required

Performance

Criteria

Performance

Criteria

Complied To

Test Result









of Line .




Page: 198 of 217


Description : Power Frequency Magnetic Field Test Setup

Test Mode : Mode 2



Page: 199 of 217

Test Mode : Mode 3


Test Mode : Mode 4



Page: 200 of 217

14. Voltage Dips and Interruption



14.2. Test Setup

14.3. Limit

Item Environmental

Phenomena

Units Test Specification Performance

Criteria

Input AC Power Ports

% Reduction

Period

30

25 C

Voltage Dips

% Reduction

Period

>95

0.5 B

Voltage Interruptions % Reduction

Period

> 95

250 C


Page: 201 of 217


The EUT and its load are placed on a table which is 0.8 meter above a metal ground plane

measured 1m*1m min. And 0.65mm thick min. And projected beyond the EUT by at least

0.1m on all sides. The power cord shall be used the shortest power cord as specified by the

manufacturer.

For Voltage Dips/ Interruptions test:

The selection of test voltage is based on the rated power range. If the operation range is

large than 20% of lower power range, both end of specified voltage shall be tested.

Otherwise, the typical voltage specification is selected as test voltage.

The EUT is connected to the power mains through a coupling device that directly couples to

the Voltage Dips and Interruption Generator.

The EUT shall be tested for 30% voltage dip of supplied voltage and duration 25 Periods,

for 95% voltage dip of supplied voltage and duration 0.5 Periods with a sequence of three

voltage dips with intervals of 10 seconds, and for 95% voltage interruption of supplied

voltage and duration 250 Periods with a sequence of three voltage interruptions with

intervals of 10 seconds.

Voltage phase shifting are shall occur at 00, 450, 900 ,1350 ,1800 ,2250, 2700 ,3150 of the

voltage.


No deviation.


Page: 202 of 217


Test Item Voltage dips and interruption

Test Mode Mode 1


Voltage Dips and

Interruption

Reduction(%)

Angle Test Duration

(Periods)

Required

Performance

Criteria

Performance

Criteria

Complied To

Test Result

30 0 25 C A PASS

30 45 25 C A PASS

30 90 25 C A PASS

30 135 25 C A PASS

30 180 25 C A PASS

30 225 25 C A PASS

30 270 25 C A PASS

30 315 25 C A PASS

>95 0 0.5 B A PASS

>95 45 0.5 B A PASS

>95 90 0.5 B A PASS

>95 135 0.5 B A PASS

>95 180 0.5 B A PASS

>95 225 0.5 B A PASS

>95 270 0.5 B A PASS

>95 315 0.5 B A PASS

>95 0 250 C B PASS

>95 45 250 C B PASS

>95 90 250 C B PASS

>95 135 250 C B PASS

>95 180 250 C B PASS

>95 225 250 C B PASS

>95 270 250 C B PASS

>95 315 250 C B PASS Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information

The nominal voltage of EUT is 230V. EUT stopped operation and could / could not be reset by operator at kV

of Line . No false alarms or other malfunctions were observed during or after the test. The acceptance



Page: 203 of 217

Product Notebook PC


Test Mode Mode 2


Voltage Dips and

Interruption

Reduction(%)

Angle Test Duration

(Periods)

Required

Performance

Criteria

Performance

Criteria

Complied To

Test Result

30 0 25 C A PASS

30 45 25 C A PASS

30 90 25 C A PASS

30 135 25 C A PASS

30 180 25 C A PASS

30 225 25 C A PASS

30 270 25 C A PASS

30 315 25 C A PASS

>95 0 0.5 B A PASS

>95 45 0.5 B A PASS

>95 90 0.5 B A PASS

>95 135 0.5 B A PASS

>95 180 0.5 B A PASS

>95 225 0.5 B A PASS

>95 270 0.5 B A PASS

>95 315 0.5 B A PASS

>95 0 250 C B PASS

>95 45 250 C B PASS

>95 90 250 C B PASS

>95 135 250 C B PASS

>95 180 250 C B PASS

>95 225 250 C B PASS

>95 270 250 C B PASS






Page: 204 of 217

Product Notebook PC


Test Mode Mode 3


Voltage Dips and

Interruption

Reduction(%)

Angle Test Duration

(Periods)

Required

Performance

Criteria

Performance

Criteria

Complied To

Test Result

30 0 25 C A PASS

30 45 25 C A PASS

30 90 25 C A PASS

30 135 25 C A PASS

30 180 25 C A PASS

30 225 25 C A PASS

30 270 25 C A PASS

30 315 25 C A PASS

>95 0 0.5 B A PASS

>95 45 0.5 B A PASS

>95 90 0.5 B A PASS

>95 135 0.5 B A PASS

>95 180 0.5 B A PASS

>95 225 0.5 B A PASS

>95 270 0.5 B A PASS

>95 315 0.5 B A PASS

>95 0 250 C B PASS

>95 45 250 C B PASS

>95 90 250 C B PASS

>95 135 250 C B PASS

>95 180 250 C B PASS

>95 225 250 C B PASS

>95 270 250 C B PASS






Page: 205 of 217

Product Notebook PC


Test Mode Mode 4


Voltage Dips and

Interruption

Reduction(%)

Angle Test Duration

(Periods)

Required

Performance

Criteria

Performance

Criteria

Complied To

Test Result

30 0 25 C A PASS

30 45 25 C A PASS

30 90 25 C A PASS

30 135 25 C A PASS

30 180 25 C A PASS

30 225 25 C A PASS

30 270 25 C A PASS

30 315 25 C A PASS

>95 0 0.5 B A PASS

>95 45 0.5 B A PASS

>95 90 0.5 B A PASS

>95 135 0.5 B A PASS

>95 180 0.5 B A PASS

>95 225 0.5 B A PASS

>95 270 0.5 B A PASS

>95 315 0.5 B A PASS

>95 0 250 C B PASS

>95 45 250 C B PASS

>95 90 250 C B PASS

>95 135 250 C B PASS

>95 180 250 C B PASS

>95 225 250 C B PASS

>95 270 250 C B PASS






Page: 206 of 217


Description : Voltage Dips Test Setup

Test Mode : Mode 2



Page: 207 of 217

Test Mode : Mode 3


Test Mode : Mode 4



Page: 208 of 217

15. Attachment EUT Photograph

(1) EUT Photo

(2) EUT Photo


Page: 209 of 217

(3) EUT Photo

(4) EUT Photo


Page: 210 of 217

(5) EUT Photo

(6) EUT Photo


Page: 211 of 217

(7) EUT Photo

(8) EUT Photo


Page: 212 of 217

(9) EUT Photo

(10) EUT Photo


Page: 213 of 217

(11) EUT Photo

(12) EUT Photo


Page: 214 of 217

(13) EUT Photo

(14) EUT Photo


Page: 215 of 217

(15) EUT Photo

(16) EUT Photo


Page: 216 of 217

(17) EUT Photo

(18) EUT Photo


Page: 217 of 217

(19) EUT Photo

(20) EUT Photo


Page: 218 of 217

(21) EUT Photo

(22) EUT Photo

test report - faenl.msi.comfaenl.msi.com/ftp/ce documents/notebook/ms-16y1 (cx640,cr640... · the...

Documents