Requirements:

1. Basic knowledge on PC software installation or brain.exe

2. A Cherry Mobile Burst 2.0 Smart Phone which can’t be restored to its normal state thru

restoration of backup, wipe data factory reset or dead device that has no hardware

damages.

3. Your devices’ USB cable.

4. Internet Connection for PC.

5. PC with 32-bit or 64-bit windows OS (I have only tested this on Windows 7), pre-installed

with Archive Software (I prefer WinRAR Archiver).

6. Downloaded CM Burst2.0 Full Stock ROM Integrated In SP Flashing Tool.

7. A ton of common sense, patience and back reading attitude is a must.

Note: Click on underlined word, name or sentences for download links.

WARNING: Do This At Your Own Risk!!!

I/We will not take any form of responsibility on whatever happens to

your device when doing this procedure. These procedures are only

made based on my personal experience unbricking my own device.

Credits to…

Sir Rik Villorente

Sir George Simon Ohm

Cherry Mobile Burst 2.0 Custom Development Group

XDA-forum

Who shared their files unconditionally and gave me guidance when my device

got bricked.

Procedures:

A. Prepare on hand all the necessary tools needed (make sure all files needed has been

dowloaded.

B. Install your Downloaded Archiver in your PC

C. Extract “CM Burst2.0 Full Stock ROM Integrated In SP Flashing Tool” and place the whole

folder extracted on the desktop of your PC.

D. Open CM Burst2.0 Full Stock ROM Integrated In SP Flashing Tool/Driver Auto Installer/and

right click Install.bat (Windows Batch File)/Run as administrator and follow prompts…

(if you believe you already have the required drivers or have previously used SP Flash on

the same device, skip this driver installation)

E. Now go back and enter SP Flash Tool v3.1316.0.150/Flash_tool.exe and right click

to run as administrator…

F. With the SP Flash Tool Open, click on Scatter-loading/direct its path to your Desktop/CM

Burst2.0 Full Stock ROM Integrated In SP Flashing Tool/SP Flash Tool v3.1316.0.150/CM

Burst2.0 Full Stock ROM/MT6589_Android_scatter_emmc.txt and clock open.

G. Make sure the necessary files needed have a check in its tick box and has a file path…

refer to image below.

H. Take out the Batteries, Sim Card and SD Card out of the device.

I. Insert USB cable to the device.

J. Click Download on the SP Flash Too and click “Yes” on the Download Warning.

K. Plug USB (which is attached to your device) to your PC and insert the battery within 2-3

seconds after plugging the USB into the PC.

L. A sound should be heard normally as plugging any device in the PC. If you still don’t

have the necessary drivers installed, windows auto update should run since you have

activated it earlier with the Driver Auto Installer.

M. If the driver was unsuccessfully installed, leave the SP Flashing Tool (do not exit the tool)

and reinstall the Driver Auto Installer to reactivate the driver update. Sometime it would

be necessary to uninstall and reinstall the Driver Auto Update or you could also take out

and reinsert your batteries quickly when a sound of unplugging on the PC is heard during

the drivers update.

N. When all the necessary drivers are installed in your PC, SP Flashing Tool will automatically

detect your device and run as shown in the images below (the images below are taken

during flashing of a different device but, it is similar to what will occur when we flash our

device).

After the yellow bar is filled and the “Download OK” window pops up, remove your device or

unplug it from the USB, close the “Download OK” window and SP Flash Tool. Take out the

batteries for at least 30seconds. Insert your Sim Card on its slot(s) and SD Card.

Now press and hold the volume up + power key until it enters the Stock Recovery (Dead Green

Android Bot Lying with its belly open protruding is a Warning Symbol; that’s when you release the

buttons). Enter the menu by pressing the power key. Use volume down to select an option,

select wipe data factory reset and press the volume up button to confirm. After the wipe is

complete do the wipe cache partition using the same keys and after the wipe select reboot

system now to boot up the device. Boot up may take up to 10mins…

When the phone has finished booting up and starts, CONGRATULATIONS!!! YOU HAVE

SUCCESSFULLY FLASHED BACK YOUR DEVICE TO ITS FACTORY DEFAULT STATE… you can now

dance around and not worry about getting bricked…