30s304-ns

2
PHILTEX/RYTON COMPLEX PIPING SPECIFICATION SPECIFICATION NUMBER: 30S304-NS SERVICE: ASME CLASS 300 NOT SPECIFIED (304 STAINLESS STEEL) (21) DATE: 6/9/04 MINIMUM C/A: 0" (38) MIN NDE: 20% MAXIMUM HARDNESS: N/A STRESS RELIEF: NO HYDROSTATIC TESTING: YES (20) PRESSURE/TEMPERATURE LIMITATIONS: ASME CLASS 300 (NOT FOR CONTINUOUS SERVICE BELOW - 150 º ) MEETS CODE(S): ASME B31.3 COLOR: N/A PHILTEX/RYTON SPEC SIZE ½ & ¾ 1 1 ½ 2 3 4 6 8 10 12 14 16 18 20-24 FLANGES (19) (30) (1) A182 F304/304L RF SW PRF'D / SE WN - SCH 40S A182 F304/304L RF WN PRF’D / S0 WN – SCH 10S A182 F304/304L RF WN PRF’D / SO WN – SCH 10S FITTINGS ELL, TEE, RED, CAP (1) SW - A182 F304/304L 3000# PRF'D SE - A182 F304/304L 2000# BW- A403 WP304/304L SCH 40S A403 WP304/304L SCH 10S A403 WP304/304L SCH 10S CPLGS- INLINE (1) SW - 182 F304/304L 3000# PRF'D SE - A182 F304/304L 3000# XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX BRANCH CONNECT USE THE TABLE IN SECTION 3.6 OF THE APPPLICATION GUIDELINES PIPE SIZE ½ & ¾ 1 1 ½ 2 3 4 6 8 10 12 14 16 18 20-24 NIPPLE (5) (17)(38) A312 TP304/304L SE- SCH 80S SMLS XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX SE (5) A312 TP304/304L SCH 80S SMLS XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX BW / SW (5) A312 TP304/304L SCH 40S SMLS A312 TP304/304L SCH 10S EFW A312 TP304/304L SCH 10S EFW WELDOLET & BW ELBOLET 2 IN A182 F304/304L SCH 40S BOLTING MATERIAL A193 B7 STUD OR A193 B7 STUD WITH BLUE XYLON 1014 OR 1424 COATING. NEVER MIX COATED BOLTS WITH UNCOATED BOLTS. WELDOLET & BW ELBOLET 3 IN – 6 IN A182 F304/304L SCH - 10S NUTS A194 2H HEAVY HEX NUTS/ A194 2H HEAVY HEX NUTS WITH BLUE XYLON 1014 OR 1424 COATING: USE COATED ONLY WITH COATED BOLTS. SOCKOLET, THREDOLET, SE & SW ELBOLET A182 F304/304L 3000# GASKETS (1)CORRUGATED 316SS W/GRAPHITE PRF’D. IDT “WD-20”, J M CLIPPER “ELASTOGRAPH”, GARLOCK “GRAPHONIC” ALL ACCEPTABLE. (2)IN AREAS WHERE GRAPHONICS GASKETS WILL NOT ACCOMMODATE FLANGE CAP USE SPIRAL WOUND 316 SS WITH GRAPHITE FILL (3)USE GRAPHONICS WITH NICKEL 200 AT RYTON PLUGS, SOLID, ROUND HEAD A182 F304/304L (15) TUBING (1/2 & SMALLER) SMLS 316 STAINLESS STEEL ( .035 WALL) BUSHINGS A182 F304/304L (16) SWAGELOK TUBING FITTINGS 316 STAINLESS STEEL UNIONS SW –A182 F304/304L3000# - FLANGES PRF'D THREAD COMPOUND RECTORSEAL/ VIRGIN TEFLON/ GLADIATOR PASTE SWAGE NIPPLE FOR 2 IN PIPE A403 WP304/304L SCH 80S SMLS THERMOWELL CONNECTION THREDOLET / SE ELBOLET PRF'D or FLANGED 316 SS THERMOWELL PRF'D Philtex/Ryton Mechanical Design Engineering must approve any exceptions to these specifications for any job on a case-by-case basis. 30S304-NS REV: 2

Upload: vipin-nair

Post on 03-Oct-2015

216 views

Category:

Documents


3 download

DESCRIPTION

Line specs for s304

TRANSCRIPT

PHILLIPS 66 COMPANY PHILTEX/RYTON COMPLEX PIPING SPECIFICATION

PHILTEX/RYTON COMPLEX PIPING SPECIFICATIONSPECIFICATION NUMBER: 30S304-NS

FILLIN \* MERGEFORMAT

QUOTE \* Upper \* MERGEFORMAT

FILLIN \* MERGEFORMAT

SERVICE: ASME CLASS 300 NOT SPECIFIED (304 STAINLESS STEEL) (21)DATE: 6/9/04

MINIMUM C/A: 0" (38)MIN NDE: 20%MAXIMUM HARDNESS: N/ASTRESS RELIEF: NOHYDROSTATIC TESTING: YES (20)

PRESSURE/TEMPERATURE LIMITATIONS: ASME CLASS 300 (NOT FOR CONTINUOUS SERVICE BELOW - 150 ) MEETS CODE(S): ASME B31.3COLOR: N/A

PHILTEX/RYTON SPEC

SIZE & 11 23468101214161820-24

FLANGES

(19) (30) (1)ASME FORMDROPDOWN

A182 F304/304L RF

SW PRF'D / SE

WN - SCH 40S

A182 F304/304L RF

WN PRFD / S0

WN SCH 10SA182 F304/304L RF WN PRFD / SO

WN SCH 10S

FITTINGS

ELL, TEE,

RED, CAP

(1)SW - A182 F304/304L 3000# PRF'D

SE - A182 F304/304L 2000#

BW- A403 WP304/304L SCH 40S

A403

WP304/304L

SCH 10S

A403 WP304/304L

SCH 10S

CPLGS-

INLINE

(1)SW - 182 F304/304L 3000# PRF'D

SE - A182 F304/304L 3000#

XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

BRANCH CONNECTUSE THE TABLE IN SECTION 3.6 OF THE APPPLICATION GUIDELINES

PIPE

SIZE & 11 23468101214161820-24

NIPPLE (5)

(17)(38)A312 TP304/304L SE- SCH 80S SMLS SW- SCH40SXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

SE

(5)A312 TP304/304L SCH 80SSMLS

XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

BW / SW

(5)A312 TP304/304L SCH 40SSMLSA312 TP304/304L SCH 10S

EFW

A312 TP304/304L SCH 10SEFW

WELDOLET & BW ELBOLET ( 2 INA182 F304/304L SCH 40SBOLTING MATERIALA193 B7 STUD OR A193 B7 STUD WITH BLUE XYLON 1014 OR 1424 COATING. NEVER MIX COATED BOLTS WITH UNCOATED BOLTS.

WELDOLET & BW ELBOLET 3 IN 6 INA182 F304/304L SCH - 10SNUTSA194 2H HEAVY HEX NUTS/ A194 2H HEAVY HEX NUTS WITH BLUE XYLON 1014 OR 1424 COATING: USE COATED ONLY WITH COATED BOLTS.

SOCKOLET, THREDOLET, SE & SW ELBOLETA182 F304/304L 3000#GASKETS(1)CORRUGATED 316SS W/GRAPHITE PRFD. IDT WD-20, J M CLIPPER ELASTOGRAPH, GARLOCK GRAPHONIC ALL ACCEPTABLE.

(2)IN AREAS WHERE GRAPHONICS GASKETS WILL NOT ACCOMMODATE FLANGE CAP USE SPIRAL WOUND 316 SS WITH GRAPHITE FILL

(3)USE GRAPHONICS WITH NICKEL 200 AT RYTON

PLUGS, SOLID, ROUND HEADA182 F304/304L (15)TUBING (1/2 & SMALLER) SMLS 316 STAINLESS STEEL ( .035 WALL)

BUSHINGSA182 F304/304L (16)SWAGELOK TUBING FITTINGS 316 STAINLESS STEEL

UNIONSSW A182 F304/304L3000# - FLANGES PRF'DTHREAD COMPOUNDRECTORSEAL/ VIRGIN TEFLON/ GLADIATOR PASTE

SWAGE NIPPLE FOR ( 2 IN PIPEA403 WP304/304L SCH 80S

SMLSTHERMOWELL CONNECTIONTHREDOLET / SE ELBOLET PRF'D or FLANGED316 SS THERMOWELL PRF'D

Philtex/Ryton Mechanical Design Engineering must approve any exceptions to these specifications for any job on a case-by-case basis.30S304-NSREV: 2

PHILTEX/RYTON COMPLEX PIPING SPECIFICATIONSPECIFICATION NUMBER: 30S304-NS

SERVICE: ASME CLASS 300 NOT SPECIFIED (304 STAINLESS STEEL) (21)DATE: 6/9/04

Valves listed below are preferred Consult the Phillips Engineering Standards for the other acceptable alternatives.

Orbit valves are considered a specialty item consult engineering. All valve bolting (bonnet and packing ) shall match the body metallurgy.

SIZE -1 23468 1214 - 24

GATE

OS&Y

BODY MATERIAL

TRIM MATERIAL

PACKING MATERIAL

BONNET CONSTRUCT

END CONNECTION

NOTESA182 F316/316L (800#) 316 SS HF GRAPHITE (23)

BOLTED / WELDED SE / FE PRF'D

API 602 (6)

A351 CF8 316 SS HF

GRAPHITE (23)BOLTEDFEAPI 600

CHECK

(14) (25)BODY MATERIAL

TRIM MATERIAL

SPRING MATERIAL

END CONNECTION

NOTESA182 F316/316L

316 SS HF

SE / FE PRF'D

(800#)

A351 CF8 316 SS

INCONEL X-750FEWATER

BUTTERFLY

FIRESAFE

API 607

API 609

(25)BODY MATERIAL

TRIM MATERIAL

PACKING MATERIAL

END CONNECTION

NOTESUSE BALL VALVEA351 CF8 316 SS

GRAPHITE (23)FEWAFER DOUBLE OFFSET (MIN.)

BALL

FIRESAFE

API 607

API 608

BODY MATERIAL

TRIM MATERIAL

PACKING MATERIAL

SEAT MATERIAL

END CONNECTION

NOTESA182 F316/316L

316 SS

GRAPHITE (23)

GLASS FILL TEFLON

SE / FE PRF'D

(6) JAMESBURY 9FB-3600XTA351 CF8 316 SSGRAPHITE (23)GLASS FILL TEFLONFEJAMESBURY 5300-31-3600XT

PLUG

FIRESAFE

API 607

BODY MATERIAL

PLUG MATERIAL

SLEEVE MATERIAL

END CONNECTION

NOTESA351 CF8

304 SS

TEFLON

SE / FE PRF'D

(6)

A351 CF8 304 SSTEFLONFE

GLOBE

OS&Y

BODY MATERIAL

TRIM MATERIAL

PACKING MATERIAL

BONNET CONSTRUCT

END CONNECTION

NOTESA182 F316/316L (800#) 316 SS HF GRAPHITE (23)

BOLTED

SE / FE PRF'DA351 CF8 316 SS HFGRAPHITE (23)BOLTEDFE

Notes:

(1) Use socket weld fittings except in areas where welding is not permitted.

(5) All first take-off piping thread nipples to 1 to first block valve shall be schedule 80 and stamped 80.

(6) Atmospheric vent and drain valves must be 1.

(14) Use only spring loaded check valves in vertical lines. Do not install any check valve with normal flow direction being down.

(15) No hexagonal head or hollowed out plugs allowed.

(16) Bushings to be a minimum of two size reductions. Use only on instruments takeoffs downstream of block valve.

(17) No all thread nipples allowed.

(19) Although one may be preferred over the other, slip-on flanges and weld neck flanges are interchangeable.

(20) If hydrotesting with water, the chloride content must be less than 250 ppm.

(21) Stainless steel 304L is acceptable substitutes for stainless steel 304.

(23) Valves shall have die formed graphoil rings with braided graphite wiper ring top and bottom with corrosion inhibitor

(25) Equipment installed between flanges, i.e., wafer butterfly and check valves and some control valves, requires fire insulation or shielding of the flange bolts.

(30) Locate flanges in horizontal lines where possible.

(38) If C/A of 1/16" is needed, all screwed piping 1/2" - 1 1/2" shall be schedule 80 or 80S.