ford mondeo quick reference · pdf fileabout this quick reference guide thank you for choosing...

FORD MONDEO Quick Reference Guide

The information contained in this publication was correct at the time of going to print. In the interest ofcontinuous development, we reserve the right to change specifications, design or equipment at any timewithout notice or obligation. No part of this publication may be reproduced, transmitted, stored in aretrieval system or translated into any language in any form by any means without our written permission.Errors and omissions excepted.© Ford Motor Company 2011

All rights reserved.Part Number: CG3562en 10/2011 20110817082719

ABOUT THIS QUICKREFERENCE GUIDEThank you for choosing Ford. Werecommend that you take some time to getto know your vehicle better by reading thisQuick Reference Guide, which summarisessome important aspects of your Owner'sManual. The more that you know aboutyour vehicle, the greater the safety andpleasure you will get from driving it.

This Quick Reference Guide must beread in conjunction with the Owner'sManual.

WARNINGAlways drive with due care andattention when using and operatingthe controls and features on your

vehicle.

AT A GLANCEInstrument panel overview - left-hand drive

E87719

A J K L M NC DB H IGFE

P OV U T S R Q

1

Instrument panel overview - right-hand drive

E87720

ED F G B AML H CI

O QU T S R VP

N J K

Lighting controls.AAir vents.BDirection indicators. Telephone control buttons. Voice control buttons. Lanedeparture warning control buttons.

C

Audio controls.DInstrument cluster.EInformation display controls.FWiper lever.GStart Button.HAudio or navigation unit.IStability control (ESP) switch. Start-stop switch.JParking aid switch.KHazard warning flasher switch.LPassenger airbag deactivation warning lamp.MHeated windscreen and heated rear window switches.NClimate controls.O

2

Cigar lighter.PIgnition switch.QCruise control and speed limiter switches. Adaptive cruise control switches. Speedlimiter switches.

R

Steering wheel adjustment lever.SHorn.TCruise control and speed limiter switches. Adaptive cruise control switches. Speedlimiter switches.

U

Driver Knee airbag.V

KEYLESS ENTRY

WARNINGSFor all warnings and cautions, referto your Owner's handbook.The keyless entry system may notfunction if the key is close to metalobjects or electronic devices such as

mobile phones.

E78276

Passive locking and unlocking requires avalid passive key to be located within oneof the three external detection ranges.

Locking the vehicleNote: Once activated, the vehicle will remainlocked for approximately three seconds. Thisis to allow you to pull a door handle andcheck if the vehicle is locked.

E87384

Locking buttons are located on each of thefront doors.Press a locking button once.

Unlocking the vehicle

E78278

Pull one of the door handles.

3

Locking and unlocking the doorswith the key blade

1

2

1

E87964

1. Carefully remove the cover.2. Remove the key blade and insert it into

the lock.

AUTOWIPERS

WARNINGFor all warnings and cautions, referto your Owner's handbook.

E71013

C

A B

Low sensitivityAOnBHigh sensitivityC

The rain sensor will continuously measurethe amount of water on the windscreen andadjust the speed of the front wipersautomatically.

Adjust the sensitivity of the rain sensorusing the rotary control.

CHANGING THE WIPER BLADES


Windscreen wiper bladesCAUTION

Set the windscreen wipers in theservice position to change the wiperblades.

Service position

E85833

A

E75188

Switch off the ignition and move the wiperlever to position A within three seconds.Release the lever when the windscreenwipers have moved to the service position.

4

AUTOMATIC MAIN BEAMCONTROL

WARNINGSFor all warnings and cautions, referto your Owner's handbook.The system does not relieve you ofyour responsibility to drive with duecare and attention. A manual override

may be necessary if the system fails toswitch the main beam on or off.

CAUTIONIn cold and severe weather conditionsthe system may not function. A manualoverride may be necessary in these

cases.

The system will automatically switch onmain beam if it is dark enough and no othertraffic is present. If it detects anapproaching vehicle’s headlamps or taillamps, or street lighting ahead the systemwill switch off main beam before it candistract other road users.Once the system is active the main beamwill switch on if:• it is dark enough to require the use of

main beams and• there is no traffic or street lighting

ahead and• vehicle speed is greater than 40 km/h

(25 mph).The main beam will switch off if:• The ambient light is high enough that

main beam is not required.• An approaching vehicle's headlamps or

tail lamps are detected.• Street lighting is detected.• Vehicle speed falls below 25 km/h (16

mph).• The camera sensor is too hot or

becomes blocked.

Activating the systemSwitch on the system using the informationdisplay and autolamps.

E70719

Turn the switch to the autolamps position.

Manually overriding the system

E70725

Use the main beam lever to switch betweenmain beam and dipped beam.

POWER WINDOWS


5

Driver’s door switches

E121510

You can operate all the windows with theswitches on the door trim panel of thedriver’s door.To reduce wind noise or buffeting when justone window is open, open the oppositewindow slightly.

ELECTRIC EXTERIOR MIRRORS

A CB

E70846

Left-hand mirrorAOffBRight-hand mirrorC

Mirror tilting positions

E70847

Reverse mirror dippingDepending on the switch position (A or C),the relevant exterior mirror will dipwhenever you select reverse gear, givingyou a view of the kerb.Note: You can disable this feature by leavingthe switch in position B.The exterior mirror will return to the originalposition:• If the vehicle speed exceeds 10 km/h (6

mph).• Approximately 10 seconds after reverse

gear has been disengaged.• If the switch is returned to position B.

BLIND SPOT MONITOR


Blind spot information system(BLIS)The system is a convenience feature thataids the driver in detecting vehicles thatmay have entered the blind spot zone (A).The system will alert you if certain vehiclesenter the blind spot zone whilst driving.

6

A

A

E124788

Using the systemThe system displays a yellow indicatorlocated in the exterior mirrors.

E124736

Detection limitationsThere may be certain instances wherevehicles entering and exiting the blind spotzones may not be detected.Instances which may cause non-detection:• Debris build up on the rear bumper

panels in the area of the sensors.• Certain manoeuvring of vehicles

entering and exiting the blind zone.• Vehicles passing through the blind zone

at high speed.• Severe weather conditions.• Several vehicles passing through the

blind zone following each other closely.

Turning the system on and offYou can turn the system on and off usingthe information display.

MANUAL CLIMATE CONTROLCooling the interior quickly

E71381

Heating the interior quickly

E71377

Recommended settings for cooling

E131534

Open the centre and side air vents.Direct the air vents toward your face.

Recommended settings for heating

E131535

Open the centre and side air vents.

7

Direct the side air vents toward the sidewindows.

Defrosting and demisting thewindscreenNote: Turn the air conditioning on to assistwindscreen and side window demisting.Note: Turn the heater control to maximumheat to assist windscreen and side windowdefrosting.

E71382

Make sure that the blower and A/C is on.The indicator in the switch will illuminateduring defrosting and demisting.If you move the air distribution control to aposition other than windscreen, the A/Cwill remain on.You can switch the air conditioning andrecirculated air on and off while the airdistribution control is set to windscreen.

AUTOMATIC CLIMATECONTROLNote: Turn the air conditioning on to assistwindscreen and side window demisting.Note: Turn the heater control to maximumheat to assist windscreen and side windowdefrosting.

E140019

Recommended settings: AUTO, 22ºC

Mono modeIn mono mode, the temperature settingsfor both the driver’s and passenger’s sideare linked. If you adjust the temperatureusing the rotary control on the driver’s side,the settings will be adjusted to the samesetting on the passenger’s side.

AUXILIARY HEATER


Parking heaterNote: The parking heater will only operateif there is at least 7.5 litres (1.6 gallons) offuel in the fuel tank and the ambienttemperature is below 15°C (59°F). Theheater will not operate if the battery is low.

Remote starting

E114360

StartingHold the transmitter with the antennaupwards and press the ON button for atleast two seconds.

Fuel operated heater (dependingon country)The fuel operated heater aids in warmingthe engine and the vehicle interior onvehicles with a diesel engine. It is switchedon or off automatically depending on theoutside air temperature and the coolanttemperature, unless you have deactivatedit.

8

To deactivate the fuel operated heater:

E70499

1. Press the right arrow button on thesteering wheel to enter the main menu.

2. Highlight Setup with the up and downarrow buttons and press the right arrowbutton.

3. Highlight Aux. Heater and press theOK button to toggle the heater on andoff. A cross appears in the box when theheater is activated.

4. Press the left arrow button to exit themenu. Hold the left arrow buttonpressed to return to the trip computerdisplay.

Diesel auxiliary heater (dependingon country)The diesel auxiliary heater (PTC electricalheater) aids in warming the vehicle interioron vehicles with a diesel engine. It isswitched on or off automatically dependingon the outside air temperature, the coolanttemperature and the alternator load.

MEMORY FUNCTION

WARNINGSBefore activating the seat memory,make sure that the area immediatelysurrounding the seat is clear of

obstructions and that all occupants areclear of moving parts.

The memory store function cannotbe used when the vehicle is moving.

A

B

E86768

Seat adjustment controlsAMemory pre-set buttonsB

Up to four different driver's seat andexterior mirror positions can be stored inthe memory. Your preferred setting for thereverse mirror dipping feature can also bestored.

Setting a memory pre-setPassive settingThe vehicle stores the seating and mirrorpositions for up to four remote controls orpassive keys. Next time the vehicle isunlocked, the position of the seat andmirrors will adjust to the last used position.Each time you turn the ignition off, thecurrent seat and mirror settings are storedon the remote control or passive key used.

Active setting1. Turn the ignition on.2. Adjust the seat and exterior mirrors to

the desired position.3. Press and hold the desired pre-set

button B until a single chime sounds toconfirm.

9

Recalling a stored seat positionNote: To stop seat movement during arecall, press any driver seat adjustmentcontrol, any of the memory buttons or anymirror control switch. Seat movement willalso stop if you move the vehicle.

Passive recallNote: If more than one passive key is inrange, the memory function will move to thesettings of the first key stored.When you unlock the vehicle with theremote control or pull the driver door handlewith a passive key in range, the seat andmirrors will move to the position stored onthat remote control or passive key.

Active recallPress the pre-set button associated withthe desired driving position. The seat andmirrors will move to the position stored onthat pre-set.

Resetting the memoryIf any seat position travel is interrupted (e.g.an obstacle in the way or loss of powersupply), you will need to reset the memory.Note: Make sure all electrical accessoriesare switched off.1. Turn the ignition to position II.2. Operate the seat adjustment control to

move the seat in the required directionuntil it stops. A click will be heard.

3. Release the seat adjustment controland immediately press and hold theswitch in the same direction for at least3 seconds. Keep it held until the seatstops at the mechanical end of its traveland a click is heard.

4. Release the seat adjustment control.5. Operate the same seat adjustment

control in the opposite direction for atleast 3 seconds. Keep it held until theseat stops at the mechanical end of itstravel and a click is heard.

KEYLESS STARTING

WARNINGSFor all warnings and cautions, referto your Owner's handbook.The keyless starting system may notfunction if the key is close to metalobjects or electronic devices such as

mobile phones.

E85766

Press the start button once.

Starting with automatictransmissionNote: Releasing the brake pedal duringengine start may stop the engine crankingand return to ignition on.1. Make sure the transmission is in P or N.2. Fully depress the brake pedal.3. Press the start button.

Starting with manual transmissionNote: Releasing the clutch pedal duringengine start will stop the engine cranking andreturn to ignition on.1. Fully depress the clutch pedal.2. Press the start button.

10

Stopping the engine when thevehicle is moving

WARNINGSwitching off the engine when thevehicle is still moving will result in aloss of brake and steering assistance.

The steering will not be locked, but highereffort will be required. When the ignition isswitched off some electrical circuits,warning lamps and indicators may also beOFF.

Press and hold the start button for twoseconds, or press twice within two seconds.

DIESEL PARTICULATE FILTERDuring regeneration at low speed or engineidle, you may smell a hot metallic odourand could notice a clicking metallic sound.This is due to the high temperaturesreached during regeneration and is normal.

USING START-STOP


Note: The system is on by default. To switchthe system off, press the switch in theinstrument panel. The system will only bede-activated for the current ignition cycle.To turn it on, press the switch again.

To stop the engine1. Stop the vehicle.2. Move the gear lever to the neutral

position.3. Release the clutch pedal.4. Release the accelerator pedal.The system may not shut down the engineunder certain conditions, for example:

• To maintain the interior climate.• Low battery voltage.• The outside temperature is too low or

too high.• The driver's door has been opened.• Low engine operating temperature.• Low brake system vacuum.• If a road speed of 5 km/h (3 mph) has

not been exceeded.

To re-start the engineNote: The gear lever must be in the neutralposition.Depress the clutch pedal.The system may automatically restart theengine under certain conditions, forexample:• Low battery voltage.• To maintain the interior climate.

ECO MODEThe system assists the driver to drive moreefficiently by constantly monitoringcharacteristics of gear changing,anticipation of traffic conditions and speedson motorways and open roads.

Type 1

E121813A B C

Gear shiftingAAnticipationBEfficient speedC

Type 2 and 3The relevant information will be shown inthe display.

11

Gear shiftingUsing the highest drivable gear appropriatefor the road conditions will improve fuelconsumption.

AnticipationAdjusting your vehicle speed and thedistance to other vehicles without the needfor heavy braking or acceleration willimprove fuel consumption.

Efficient speedHigher speeds use more fuel. Reducing yourcruising speed on open roads will improvefuel consumption.

USING ECO MODEThe system is accessed using the relevantinformation display menu.

Resetting Eco modeReset the average fuel consumption.Note: New values may take a short time tocalculate.

FUEL FILLER FLAP

WARNINGFor all warnings and cautions, referto your Owner's Manual.

E86613

Press the flap to open it. Open the flap fullyuntil it engages.

E139202

A

A

Insert the fuel nozzle up to and includingthe first notch on the nozzle A. Keep itresting on the cover of the fuel pipeopening.

WARNINGWe recommend that you remove thefuel nozzle slowly to allow anyresidual fuel to drain into the fuel

tank. Alternatively you can wait 10 secondsbefore removing the fuel nozzle.

E119081

Slightly raise the fuel nozzle to remove it.

FUEL CONSUMPTIONCheck your tyre pressures regularly tooptimise fuel economy.

12

HINTS ON DRIVING WITH ANTI-LOCK BRAKESWhen the ABS is operating, the brake pedalwill pulse. This is normal. Maintain pressureon the brake pedal.The ABS will not eliminate the dangersinherent when:• you drive too close to the vehicle in front

of you.• the vehicle is aquaplaning.• you take corners too fast.• the road surface is poor.

USING THE PARKING AID


Switching the parking aid on andoffNote: The parking aid switches offautomatically when you start the engine orwhen you exceed 16 km/h (10 mph).Note: The front and rear sensors are alwaysactivated or deactivated together.The parking aid is per default off. To switchthe parking aid on, press the switch in theinstrument panel or select reverse gear.The light in the switch illuminates when theparking aid is activated.To turn it off, press the switch again.

DRIVER ALERT

WARNINGSFor all warnings and cautions, referto your Owner's handbook.The system does not relieve you ofyour responsibility to drive with duecare and attention.

WARNINGSTake regular rest breaks as requiredand do not wait for the system towarn you if you feel tired.

CAUTIONSIn cold and severe weather conditionsthe system may not function. Rain,snow, spray and large contrasts in

lighting can all influence the sensor.The system may not operate on roadswith sharp bends or narrow lanes.

The system automatically monitors yourdriving behaviour using various inputsincluding the front camera sensor.If the system detects that you are becomingdrowsy or there is a deterioration in yourdriving, the system will alert you.

USING DRIVER ALERTSwitching the system on and offActivate the system using the informationdisplay.

System displayWhen active the system will runautomatically in the background and onlyissue warnings if required. You can view thestatus at any time using the informationdisplay.The alertness level is shown by six steps asa coloured bar.

E131358

The status bar will travel from left to rightas the calculated alertness level decreases.• Green - No rest required.• Yellow - First (temporary) warning.• Red - Second warning.

13

LANE DEPARTURE WARNING

WARNINGSFor all warnings and cautions, referto your Owner's handbook.The system does not relieve you ofyour responsibility to drive with duecare and attention.

CAUTIONSIn cold and severe weather conditionsthe system may not function. Rain,snow, spray and large contrasts in

lighting can all adversely influence thesensor.

The system may not operate on roadswith sharp bends or narrow lanes.

The system will automatically detect andtrack the lane markings on the road. If itdetects that the vehicle is unintentionallydrifting towards the lane boundaries thena visual warning will be displayed in theinformation display. There is also a warninggiven in the form of a vibration felt throughthe steering wheel.

USING LANE DEPARTUREWARNINGSwitching the system on and off

E131360

A

B

System onASystem offB

System warnings

E131363

A column of lane markings is displayedeither side of the vehicle graphic.The lane markings are colour coded asfollows:• Green - The system is ready to warn you

of any unintentional lane departure.• Red - The vehicle is approaching or is

too close to the detected laneboundary. Take immediate safe actionto reposition the vehicle.

• Grey - The relevant lane boundary willbe suppressed.

Instances where a lane boundary may besuppressed:• Lane markings on the road may not be

detected by the sensor.• The direction indicator for that side of

the vehicle is on.• During hard acceleration and braking,

or if direct steering is applied.• Vehicle speed is outside the operating

limits• If there is an ABS or Stability Control

(ESP) intervention.• Narrow lane width.If the lane markings turn red or a vibrationis felt through the steering wheel you musttake immediate and safe action to align thevehicle and correct any unintended lanedrift.

14

SETTING THE CLOCK ANDDATE ON THE AUDIO UNIT1. Press the CLOCK button to display the

date and time.2. Use the left or right arrow button to

select the date or time value that youwish to change. The selected value willflash in the display.

3. Turn the volume control to change theselected date or time value.

4. Use the left or right arrow button toselect additional date or time valuesthat you wish to change.

5. Turn the volume control to change theselected date or time value.

6. Press the CLOCK button to exit andsave the new date and time.

AUTOMATIC VOLUMECONTROLWhen available, automatic volume control(AVC) adjusts the volume level tocompensate for engine noise and roadspeed noise.1. Press the MENU button repeatedly until

an AVC display appears.2. Use the left or right arrow button to

adjust the AVC setting.

BLUETOOTH SETUPThe Bluetooth mobile phone part of thesystem provides interaction with the audiosystem and your mobile phone. It allowsyou to use the audio system to make andreceive calls without having to hold yourmobile phone.During bonding, if your mobile phone asksyou to authorize the automatic connection,select YES.Refer to your Owner's Manual and alsowww.ford-mobile-connectivity.com fordetails.

15

ford mondeo quick reference · pdf fileabout this quick reference guide thank you for choosing...

Documents