gujarat water supply & sewerage board...gujarat water supply & sewerage board

GUJARAT WATER SUPPLY &

SEWERAGE BOARD

107496

Stamp

Subject: SOR for the Year 2019-20.

Preamble:

- Gujarat Water Supply & Sewerage Board is preparing the SOR for

works of Water Supply & Drainage Projects, this SOR is followed by

GWIL and WASMO also.

- SOR for Electro-Mechanical items for the Year 2012-13 was approved

in 240th Board Meeting held on 07-03- 2012.

- For the year 2013- 14, 2014-15, 2015-16, 2016-17, 2017-18 and

2018-19 same rates of SOR of year 2012 13 are considered and

approved in 271st Board Meeting held on 28-02-2019.

- A committee was constituted for preparation of SOR vide office order

No. 603 dated 21-03 2016 and SOR preparation committee was

formed by letter No. 412 dated 17-02- 2016.

- Consultancy Services for formation of Electro-Mechanical SOR was

awarded to reputed consultants M/s Tata Consulting Engineers Ltd.

Periodically fourteen meetings of SOR committee in the presence of

the representative of M/s TCE were held.

- There after Group meetings of GWSSB senior officers & TCEL team

were held on 16-03-2019, 13-05-2019, 01-06 2019, 13-06 2019 &

15-07-2019 for final presentation to SOR scrutiny committee.

- This SOR 2019-20 for electro-Mechanical items has been approved in

the BOD No.272 of GWSSB held on dated.20/07/2019.

Important Notes:-

1) In Section-A,B,C- Proposed rates are inclusive of GST, unless otherwise specified in the item covered under annual Rate Contract.

2) In Section-D-Item No. 1,3 & 4,rates are adopted as per Electrical SOR of R&B GOG and inclusive of taxes.

3) In Section-D-Item No.2,LED Lighting & Fixtures is new Item,rates are approved seperately with & without GST.

4) In Section E & F,Approved rates are shown seperately with and without GST.

5) In Section A,B,C,E & F, WPI Old Series and New Series are compared and effect of the same is incorporated.

Sr No Particulars Unit Rate In Rs.

1 Cement Beg 260.00

2 Kapchi Cmt 990.00

3 Sand Cmt 720.00

4 Brick No 4.20

Sr No Particulars Unit Rate In Rs.

1 Skilled labour No 329.20

2 Semi-Skilled Labour No 320.20

3 Unskilled Labour No. 312.20

Sr No Particulars 2012-13 2019-20

1 Pig Iron 96.50 113.80

2 HR Coil 102.80 117.20

3 Copper Wire 104.70 107.70

4 Basic Metal & Alloys 104.60 109.50

5 Stainless Steel & Alloys 93.90 92.80

6 Aluminium 108.60 112.00

7 Wire Rod 105.30 110.70

8 Fuel & Power 106.70 98.00

9 Electricity (Industry) 101.30 105.40

Sr No Particulars 2012-13 2019-20

1 Petrol 64.00 70.00

2 High Speed Diesel 49.69 68.85

S.O.R. derived on basis of following Prevailing Rates

Details For Rate Of Labour Establishment For SOR 2019-20

Comparision of WPI Index of basic Raw Materials

Comparision of Rates of Fuels

Section Page No."A"

1 12 23 44 105 106 107 118 119 12

10 1311 1412 1413 1414 14

17 15

18 18-20

"B"1 212 213 224 225 226 237 238 249 24

10 2611 2712 2713 2714 2815 2816 3017 3018 3019 30"C"1 312 313 314 325 336 33

Gujarat Water Supply and Sewerage BoardJalseva Bhavan,Sector-10A,Gandhinagar

INDEX

Gas Cutting of M.S./ G.I. Pipes

Drilling of bore hole by DTH rig in Rocky formationDrilling of 115 mm dia DTH bore by Inwell rig in hilly area of all district .

Facing of M.S./G.I. PipesInstallation of India mark-II Hand PumpAnnual Overhauling, Breakdown repairs of Indian Mark-II Hand PumpJacking of Pipes from failed Tube Well

ElectrologgerAir CompressorPumping test of TubewellHydrofracturing

SCHEDULE OF RATES : ELECTRO - MECHANICALYEAR : 2019-20

Details

Drilling of bore hole in Alluvial starta by Direct Rotary rig.Drilling of bore hole by DTH rig

Section A Drilling of bore Section

Geohydrological ground water investigations

Hand Pump Spares

Charges for attending the Bore holeBore Blasting

Pre-fabricated Portable Concrete mini Panel

Annexure - A/A-1Groupwise approved rate for Drilling (Unit Rate) for the year 2018-19.

Medium/Heavy duty M.S. Coupling

Section B MATERIAL SECTION

Mild Steel Cabin

M.S./ uPVC Bail Plug

Supply of Clay BallsSupply of well sorted Sevalia GravelSupply of Cement

ISI marked ERW M.S. pipesISI marked Extra Deepwell Handpumps set

Annexure - B-1/B-2/B-3Approved rate for Drilling 165/200 mm dia DTH bore for SOR for the year 2018-19.

M.S. ClampM.S. Bore PlugM.S. Reducer

Steel bent Plate suitable to ERW pipe

Trapezoidal shape ( ' V ') wire wound low carbon, Galvanized screen pipe and Stainless Steel Screen pipesuPVC Pipe Casing

H.D.P.E. PipesuPVC Column Pipe, Standard & Heavy Duty

Section C LABOUR SECTION

Fire Hose Pipe

RCC Pipes

RO SystemGI Fittings

Job work of Slotting of M.S. ERW Pipe

7 348 369 36

10 3711 37

"D"1

1.1 391.2 401.3 451.4 471.5 501.6 501.7 522

2.1 532.2 532.3 542.4 542.5 542.6 543

3.1 543.2 553.3 553.4 573.5 573.6 584

4.1 604.2 604.4 615

5.1 644.2 644.4 65"E"1 672 683 69

4A69

4B69

570

670

7A 717B 718 729 7210 7211 7212 72

Monoblock pump 3 phaseCasing: CI-FG260, Impeller : SS-CF8M & Shaft : SS:410Monoset sub. pump 3 phaseCasing: CI-FG260, Impeller : Bronze & Shaft : SS:410Single phase sub pump motor setCasing: CI-FG260, Impeller : Bronze & Shaft : SS:410Labour Charge for fishing out Sub pump set in tubewell

Portable Diesel Driven Self Priming Horizontal Pump (Dewatering set)

Panel mounting busbarsEarth Leakage circuit breaker

Labour Charge for fishing out struck up Sub pump set from boreVaccum PumpsetDrain Pumpset

Substation EquipmentSubstation Maintenance

Substation Equipment & MaintenanceMetallic Enclosure

Substation Equipment & Maintenance

3ph Bore-well Submersible PumpsControl Panel Board

Section E ELECTRO - MECHANICAL SECTION

Hiring of D.G. Sets

Danger Notice Boards

Section D ELECTRICAL SECTION (As per Electrical SOR of R&B Department)

Earthing

LED Light fixture Industrial Lighting Landscape Lighting Flourocent tubesStreet Lighting & Solar Lighting

Hiring of LCV - Medium

Wiring

Point wiring in Copper (Modular)

Hiring of Inspection Vehicle

Point wiring in Copper (TISSINO)

Loading of Hand Pump assembly/Pipes/Screens

Hiring of LCV - Small

LED Lamp & Tubes

Conduits & PipesMains & WiresConcealed Boxes & Laminated SheetsWiring AccessoriesLADDERSLamps & Fittings

Busbar chambersSwitchgears & Distribution Boards

Substation Equipment & MaintenanceRepairing of Mono Bloc MotorsRepairing of open well Horizontal Mono PumpsetsRepairing of submersible pumpsets

PVC insulated flat / round submersible copper cablesSupply of monobloc pump 3 phase Casing: CI-FG260, Impeller : Bronze & Shaft : SS:410

HSCF PumpsEnd Suction Back Pullout Pump

13 7314 7315 7716 7717 7718 7819 7820 7921 8322 8323 8424 8725 8726 8827 8828 9129 9230 9331 9332 9433 9434 10435 10436 10637 10738 10839 10840 10841 10942 11243 11444 11545 11546 12447 12648 12849 129"F"1 1312 1313 1334 1335 1346 1347 1348 1369 13710 13811 13912 13913 14014 140"G" 141-163"H" 164-166

Section G TECHNICAL SUPPORT SECTIONSection H DRAWINGS

Pressure TransmitterFloat & Board Type Level IndicatorFloat/ Displacer Type Level Switch

Clamp On Ultrasonic Flow Meter- Fixed TypeClamp On Ultrasonic Flow Meter- Portable TypeAcoustic Doppler Type Flow Meter- Regular Power OperatedWater Meters (Multijet/ Woltman Type)Water Meters (Woltman Type)Bulk Water Meters (Ultrasonic)/ Full Bore Inline Ultrasonic Flow Meter

Ultrasonic Level Transmitter

Full Bore Electromagnetic Flow Meter- Inbuilt Battery Power operated

Insertion Type Ultrasonic Flow Meter

Pressure & Vacuum Gauges with Accessories

Section F INSTRUMENTATION SECTION

HFSR (Harmonic Free Series Reactor) soft starter Flux Compensated Magnetic Amplifier (FCMA) Soft Starter11kV Ring Main Unit (RMU)Servo Controlled Automatic Voltage Stabilizer

Full Bore Electromagnetic Flow Meter- Regular Power operated

Submerged centrifugal pumpsetsLV Power Control Centre (PCC)

Single Girder crane (H.O.T & E.O.T. Type)Double Girder Crane (H.O.T & E.O.T. Type)Chain Pulley BlockLV APFC Panel

LV MCC Panel with DOL / Star Delta / ATS / Micro processorbased so starterHV VCB Switchgear PanelSolar System

Rate per KW for comprehensive work of S.I.T.C

Cable Termina ons / Join ng Kits for 6.6 kV (UE) / 11 kV (E) grade XLPE CableCable Terminations / Jointing Kits for 11 kV (UE) grade XLPE Cable415V LV Induction MotorLT Power CapacitorCable Trays & Accessories

3.3 kV (Earthed/ Unearthed) Grade Cable- Aluminium ConductorCable Terminals (Lugs)Cable GlandsCable Terminations / Jointing Kits for 1.1kV grade PVC/ XLPE Cable

Cable Termina ons / Join ng Kits for 3.3 kV (E/UE) / 6.6 kV (E) XLPE Cable

Microprocessor Based LV Variable Frequency DriveMicroprocessor Based LV Soft Starter1.1 kV Grade Cable- Aluminium / Copper Conductor11 kV (Earthed / Unearthed) Grade Cable- Aluminium Conductor6.6 kV (Earthed/ Unearthed) Grade Cable- Aluminium Conductor

Expansion Bellows

11 KV Double / Four Pole Structure AssemblyTransformer

V.T Pumps Water Lubricated

Submersible sewage Non-clog Vertical PumpPolder type submersible Pump

Sewage Nonclog,End Suction type Horizontal centrifugal Pump Sewage Nonclog,End Suction type Vertical centrifugal Pump

SECTION - "A"Rate approved for the year

2019-20

Work to be carried out by private agency

1.1Drilling of Pilot bore hole inAlluvial strata by direct Rotaryrig.

300/250 mm Mtr. As per attached Annexure-A

400 mm mtr

450 mm mtr

550 mm mtr

600 mm mtr

300 mm Zone -I 416.15

300 mm Zone -II 594.79

300 mm Zone -III 594.79

1.4

Lowering and removing of 100mm dia dropline and 32 mm diaairline for development of eachwater bearing Zones comeacross up to full depth of Deeptubewell of size 200 mm/250mm/300 mm dia for the tubewellhaving depth 186 Mtr. and abovethrough suitable air compressor.The job is for complete period ofdevelopment of tubewell.(Without charges for aircompressor.)

Job Mtr As per attached Annexure-A

Sr. No

As per attached Annexure-A

Description of Item Size Unit

Reaming of 250/300 pilot borehole including Assembling,lowering housing casing, strainerpipes, gravel packing, claypacking etc.

Item 1: Drilling of Tubewell by direct rotary rig in alluvial starta

1.2

1.3

Drilling of bore hole by Mini DRrig including lowering of pipeassembly, Gravel packing claypacking and development of borehole by washing. (For installationof Hand pump/Power pump)

Mtr.

SOR Mech 2019-20Page 1 of 166


2019-20


Sr. No Description of Item Size Unit

1.4.1

Lowering and removing of 100mm dia dropline and 32 mm diaairline for development of eachwater bearing Zones comeacross up to full depth of Deeptubewell of size 200 mm/250mm/300 mm dia for the tubewellupto 185 Mtr. deep throughsuitable air compressor. The jobis for complete period ofdevelopment. (Where water levelis very deep and 2/3rdsubmersion is not achived.) *All the required accessories,machineries etc for above jobwill have to be provided bycontractors.

Job Mtr. As per attached Annexure-A

1.5Cement sealing if necessarywithout cost of cement by meansof mud pump.

L.S As per attached Annexure-A

2.2 Zone-II - Drilling of bore hole byDTH Rig 165 mm Mtr. As per attached annexure-

B2

Mtr.

Item 2: Drill of borehole by DTH Rig.

2.1 As per attached annexure- B1

Zone I - Drilling of bore hole by DTH Rig (a) 0 to 100 mtr(b) 100 to 150 mtr

165 mm



2019-20



2.3

Drilling of 165mm dia by DTH Rig in Rocky Formation in all districts of Zone-III(Except Surendranagar District.)0 to 150 mtr. deep

211.50

2.3.1 151 to 225 mtr. deep 261.86

2.3.2 226 to 300 mtr. 283.26

2.4

Drilling of 165mm dia by DTH Rig in Sand Stone Formation in Morbi, Tankar & Wakaner Talukas of Rajkot District. 0 to 150 mtr. deep

201.53

2.4.1 151 to 225 mtr. deep 249.38

2.5Drilling of 165mm dia X 120 Mtr deep bore by DTH Rig in Clay Formation All Taluka of Zone-III

546.00

2.6

Drilling of 165mm dia X 120 Mtr deep bore by DTH Rig in Soft / Hard Rock Formation in Vadhavan, Halvad, Muli, Patdi, Dhrangadhra Lakhtar Limdi Chuda Taluka of Surendranagar District.

319.00

2.7

Drilling of 165mm dia X 225 Mtr deep bore by DTH Rig in Soft / Hard Rock Formation in Sayala and Chotila Taluka of Surendranagar District.

232.00

Drilling of 165 mm dia DTH For Zone-III Rajkot and Zone IV Junagadh



2019-20



2.8

Drilling of 200/215MM Dia bore hole in over burden rocky or loose collapsible/boulder strata & lowering of 175/200mm dia UPVC/PVC/ERW casing pipe above 12mtr upto 40 Mtr depth by DTH Rig etc. complete.For Zone-I

200/215 mm Mtr. 370.72

3.1Drilling of bore hole by DTH Rigin rocky formation in All Talukaof Zone- II

200 mm Mtr. As per attached annexure- B3

3.2

Drilling of bore hole by DTH Rig in rocky formation in All Taluka of all district of Zone-3up to 350 mtr.

200 mm Mtr. 435.00

3.3

Drilling of bore hole by DTH Rigin Sand Stone formation in AllTaluka of Zone-III (ExceptSurendranagar Dist)

200mm Mtr. 353.00

3.4

Drilling of bore hole by DTH Rigin Soft/Hard rock Area in AllTaluka of Surendranagar district& Halvad taluka of Morbi District

200mm Mtr. 453.00

Item No. 3



2019-20



3.5

Drilling of min. 250 mm dia. borehole in all strata including dualover burden strata bycombination DR/DTH rigincluding lowering 200 mm diaMS ERW pipes in bore hole asas suggested by Hydrologist(Except- Surendranagar Dist)

250/200 mm Mtr. 1127.00

3.6

Drilling of min. 325 mm dia. borehole in all strata including dualover burden strata bycombination DR/DTH rigincluding lowering 250 mm diaMS ERW pipes in bore hole asas suggested by Hydrologist(Except- Surendranagar Dist)

325/250 mm 1327.00

3.7

Drilling of 450mm dia. bore holein alluvial, boulder etc. all strataincluding lowering of pipeassembly, bottom sealing, Gravelpacking, clay packing ,development of bore hole bywashing and Air compressor &further drilling of 165 mm dia.bore hole in rocky strata etc.complete by D.R. & D.T.H. Rig assuggested by Hydrologist inZone-I & II

450/165 MM Mtr. 1433.00

3.8

Drilling of 250 mm dia. DTH Borehole in Soft Rock (Sand Stoneformation )for all districts &talukas of Saurashtra havingsand stone formation.

250mm Mtr. 425.60



2019-20



3.9Drilling of DTH Bore hole inRocky formation for all districts& talukas of Kutch

3.9.1 Soft Rock 250mm mtr. 554.00

3.9.2 Hard Rock 200 mm mtr. 554.00

3.9.3 Hard Rock 250 mm mtr. 620.48

3.10Drilling of different dia bore byDTH/ Combi. Rig in all districtsunder Zone-V Junagadh

3.10(A)

Drilling of 200/215 mm dia borehole in overburden strata by DTHRig up to required depthincluding fixing of 175/180 diaERW/ PVC pipes & further drillingof 165 mm dia bore hole in hardrock (trap etc.) strata by DTHdrilling method up to total depthof 300 mtr inl. measuring theyield by V notch and flushing ofbore etc. complete in all districtsof Zone-V.(Casing up to 12 Mts.)



2019-20



3.10.A-1 0 to 150 mtr. deep mtr. 236.88

3.10.A-2 151 to 225 mtr. deep mtr. 293.28

3.10.A-3 226 to 300 mtr. mtr. 317.25

3.10(B)

Drilling of 200/215 mm dia borehole in overburden strata by DTHRig up to required depthincluding fixing of 175/180 diaERW/ PVC pipes & further drillingof 165 mm dia bore hole in hardrock (trap etc.) strata by DTHdrilling method up to total depthof 300 mtr inl. measuring theyield by V notch and flushing ofbore etc. complete in all districtsof Zone-V.(Casing up to 12 Mts.) In case ofLowering of casing more than 12mtrs. an upto require depth therate will be considered as peritem 3.10-B-1 otherwise less than12 mtr. casing it will beconsidered as per item No.3.10.B-2

3.10.B-1 0 to 60 mtr. deep mtr. 370.72

3.10.B-2 61 to 150 mtr. deep mtr. 236.88

3.10.B-3 151 to 225 mtr. deep mtr. 293.28

3.10.B-4 226 to 300 mtr. mtr. 317.25

165mm

165mm



2019-20



3.10(C)

Drilling of 300/315 mm dia bore inover burden strata includinglowering of 204mm dia uPVC225/250mm dia PVC/MS casingpipes up to required depth andfurther drilling of 200mm diaborehole in all types of Rockystrata, Soft Rock & Hard RockStrata formation by DTH Rigincluding flushing of bore holeby air compressor andmeasuring of yield of bore by Vnotch and fixing of bore cap etc.components.(Over burden upto 12.0m)

3.10.C-1 0 to 350 mtr. deep mtr. 487.20

3.10.C-2 351 to 400 mtr. deep mtr. 861.91

3.10.C-3 401 to 450 mtr. deep mtr. 1036.46

3.10.C-4 451 to 500 mtr. mtr. 1352.86

200 mm



2019-20



3.10(D)

Drilling of 300/315 mm dia bore inall strata including dual overburden strata by combinationDR/DTH rig including lowering of204mm dia uPVC 225/250mm diaPVC/MS casing pipes up torequired depth and furtherdrilling of 200mm dia borehole inall types of Alluvial Rocky strataformation by DTH Rig includingflushing of bore hole by aircompressor and measuring ofyield of bore by V notch andfixing of bore cap etc.components. Rates for item No.3.10-E-1 is applicable mote than12 mtr. coming only otherwiseless than 12 mtr casing it will beconsidered as per item No. 3.10-E-2

200 mm

3.10.D-1 0 to 120 mtr. Deep (alluvialStrata) mtr. 1262.24

3.10.D-2 121 to 350 mtr. deep mtr. 487.20



2019-20



3.11

Drilling of 215 mm dia bore holein overburden strata (alternatelayers of lime stone & yellowsticky clay formation) by DTH Rigup to required depth (Approx. upto 70 mtr) including fixing of175/180 dia ERW/ PVC pipes(blank and slotted) & if requiredfurther drilling of 165 mm diabore hole in hard rock (trap etc.)strata by DTH drilling method upto total depth of 120 mtrincl.measuring the yield by Vnotch and flushing of boreetc.complete in the Coastal areaof saurastra.

165 MM Mtr. 611.52

Drilling of 115 mm dia DTH bore by Inwell rig in hilly area of all district .

115 mm Mtr 340.48

Electrologger charges (With carting) _ Hr.

(A)For Dept.work - For Kachh area- Rs15000/- per job for other area Rs.12000/- per job

(B) For other dept. and private work -For Kachh area- Rs. 21000/- per job for other area Rs.18000/- per job

Item No. 4

Item No. 5

Item No. 6 : Air Compressor



2019-20



6.1 400 CFM/100 PSI _ Hr. 2537.50

6.2 600 CFM/150 PSI _ Hr. 3633.70

6.3 900 CFM/200 PSI _ Hr. 7853.75

6.4 1100 CFM/300 PSI _ Hr. 9815.75

16500.00

720.00

B D.R. Bore pump test with D.G.Set _

1st 24hr up to 30 HP _ L.S. 27500.00

There after Rs/Hr _ Hr. 900.00

1st 24hr 31 to 70 HP _ L.S. 34400.00


1st 24hr morethan 70 HP _ L.S. 42775.00


For first 8 Hours with Max. upto 20

HP Sub.Pump utilised.

thereafter Rs./Hr.

Pumping test of the tubewell bysub. Pump of adequate capacityin all districtsA) 150/200/250 mm DTH borepump set.

A

Item No. 7 : Pump Test

Item No. 8 : Hydro-fracturing



2019-20



8.1

Hydrofracturing of 115mm dialow discharge existing DTHBoreHole at different depth asper geology (Maximum up to90.00 Mtr.) with single packerunit by high pressure waterjetting pump for duration ofminimum 15 minutes andflushing of bore includingmeasuring the yield by HandPump or single phase sub. pumpset.

115mm Job 9500.00

8.2

Hydrofracturing of 165mm dia low discharge existing DTH BoreHole at different depth as per geology (Maximum up to 120.00 Mtr.) with single packer unit by high pressure water jetting pump for duration of minimum 15 minutes including Pre and Post fracture, Pump Testing by sub. pump set.

165mm Job 14100.00

9.1

Geohydrological ground waterinvestigations.(With vehiclecharges)i) 100mm/ 165mm / 200mm diaDTH Boreii) 200/250mm dia Deep tubewell(with water sample)

_Bore

Bore

3000.00

12000.00

Item No. 9 : Geo-hydrological Ground Water Investigation



2019-20



9.2

Geophysical & Geohydrologicalground water investigations forfinalisation of one pin point (Withvehicle charges)

_ Bore 15000.00

10

Charges for attending the Borehole and Taking necessarymeasurements & giving opinionsfor the depth and kind of fillingMaterials and Opinion aboutcleaning of Bore hole forcleaning of bore with necessarytools and tackels.(without lifting& lowering of pump).

Minimum Charge within 50 KM L.S. 2500.00

From 51 KM to 100 KM L.S. 4000.00

Cleaning of bore hole by sandbarrel system including removingforeign materials sand, clay,pebbles etc. with necessorytools, plants and accessories .

_ Mtr. 150.00



2019-20



11

Bore blasting:-Bore blasting tothe 165 mm dia DTH bore up torequired depth from 15 Mtr to 25Mtr of required no of bores ( 5 to6 Nos ) by using requiredquantity of slurry explossiveclass -II required blast materialsuch as detonetor blastingcap,fuse ,wire including wellequipement,safety device etccomplete ( for two Blast per bore)

_

Job ( for two

Blast) per

bore

17660.00

12

Supply of Clay ball of size 25mmto 50mm from Stickly Clay at siteof work. ( As certified byHydrologist).

_ CmtAs per attached annexure-A

13Supply of Best quality of wellsorted Sevaliya gravel of size4mm to 6mm.

_ CmtAs per attached annexure-A

14 Supply of Cement. _ M.Ton As per attached annexure-A


SECTION - "A"

Sche

dule

No

Grou

p

District Talukas Pilo

t 300

/250

mm

dril

ling

400

mm

ream

ing

450

mm

ream

ing

550m

m re

amin

g

600m

m re

amin

g

Supp

ly of

Cla

y ba

ll

Supp

ly of

Gra

vel

Supp

ly of

Cem

ent

Cem

ent s

ealin

g

Botto

m s

ealin

g

Low

erin

g of

dro

p lin

e up

to 1

86

mtr

Low

erin

g of

dro

p lin

e ab

ove

186

mtr

Air C

ompr

esso

r 600

CFM

/150

PS

I

Air C

ompr

esso

r 900

CFM

/200

PS

I

Air C

ompr

esso

r 110

0 CF

M /3

00

PSI

Seal

ing

of E

xistin

g Tu

bew

ell b

y St

icky

Clay

Mtr Mtr Mtr Mtr Mtr Cmt Cmt M.Ton Job Job Mtr. Job. LS. LS. LS. Mtr.

1 A Gandhinagar Dehgam up to 300 mtr 671 206 311 413 568 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92

2 A Mehsana Vijapur, Kheralu. Vadnagar, Satlasna upto 300 mtr. 620 191 288 380 523 701 1894 5882 12388 6217 130 24122 20725 25508 32351 92

3 A BanaskanthPalanpur, Vedgam,

Dhanera, Dantiwada up to 300 mtr

628 193 291 386 531 701 1894 5882 12388 6217 128 23915 20725 25508 32351 92

4 A Kheda Alluviun Area Complete up to 300 mtr 671 206 311 413 568 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92

5 A Anand Alluviun Area Complete up to 300 mtr 671 206 311 413 568 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92

6 A Ahmedabad Dascrol up to 300 mtr 622 190 289 384 527 701 1894 5882 12388 6217 132 24592 20725 25508 32351 92

7 A Surendranagar Dasada,Lakhatar taluka up to 300 mtr 671 206 311 413 568 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92

8 A Kutch Mandvi, Naliya, Mundra up to 300 mtr 713 220 330 440 602 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92

9 B Surat Alluviun Area Complete up to 300 mtr 768 234 354 475.2 789.6 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92

10 B Bharuch Alluviun Area Complete up to 300 mtr 768 234 354 475.2 789.6 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92

11 B Navsari Alluviun Area Complete up to 300 mtr 768 234 354 475.2 789.6 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92

Annexure - AStatement showing the details of Approved rate for the Drillng by DR Rig. For the year 2019-2020

Unit

SOR Mech 2019-20

Page 15 of 166

SECTION - "A"

12 B Valsad Alluviun Area Complete up to 300 mtr 768 234 354 475.2 789.6 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92

13 B Baroda Alluviun Area Complete up to 300 mtr 863 264 397 534 886 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92

14 B Sabarkantha Bayad, Talod, Dhansura up to 300 mtr 863 264 397 534 886 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92

15 B Panchmahal Kalol, Halol up to 300 mtr 768 234 354 475.2 789.6 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92

16 B Saurashtra Coastal area complete up to 300 mtr 768 234 354 475.2 789.6 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92

17 B Amreli Chalala upto 300 mtr 768 234 354 475.2 789.6 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92

18 B Bhavnagar Sihor, Savarkunda upto 300 mtr 768 234 354 475.2 789.6 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92

19 B Rajkot Maliya upto 300 mtr 863 264 397 534 886 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92

20 B Junagadh Vanthali upto 300 mtr. 768 234 354 475.2 789.6 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92

21 C Sabarkantha Himatnagar up to 300 mtr 1223 0 588 751 1033 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92

22 C SurendranagarHalvad,Dhangadhra,Muli,Wadhavan,Chotila,Limadi,Sayal

a taluka up to 300 mtr1223 0 588 751 1033 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92

23 C Rajkot Morbi, Wankaner up to 300 mtr 1223 0 588 751 1033 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92

24 C KutchBhachau, Anjar, Bhuj,

Nakhatrana, Rapar up to 300 mtr

1117 0 536.4 686.4 945.6 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92

25 D Sabarkantha Prantij. up to 300 mtr 539 167 250 330 458 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92

26 D Ahmedabad City, Bavla, Dholka, Sanand. up to 300 mtr 533 164 246 325 454 701 1894 5882 12388 6217 132 24592 20725 25508 32351 92

27 D BanaskanthaBhabhar,Kankrej,Deodar,Deesa,Lakhani taluka up to

300 mtr538 164 250 330 456 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92

28 D Patan Vagdod up to 300 mtr 509 154 235 310 431 701 1894 5882 12388 6217 130 24122 20725 25508 32351 92

SOR Mech 2019-20

Page 16 of 166

SECTION - "A"

29 D Gandhinagar Gandhinagar, Kalol up to 300 mtr 509 154 235 310 431 701 1894 5882 12388 6217 130 24122 20725 25508 32351 92

30 D Mehsana Visnagar up to 300 mtr 522 157 241 318 442 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92

31 E Ahmedabad Detroj, Mandal, Viramgam up to 300 mtr 533 164 246 325 454 701 1894 5882 12388 6217 132 24592 20725 25508 32351 92

32 E MehsanaMehsana,Kadi,Becharaji,Unjha,Gojarya,Jotana taluka

up to 300 mtr504 154 234 308 428 701 1894 5882 12388 6217 131 24331 20725 25508 32351 92

33 E PatanPatan,Chanasma,Saraswati,Siddhapur taluka up to 300

mtr 512 156 236 312 434 701 1894 5882 12388 6217 131 24331 20725 25508 32351 92

34 E Gandhinagar Mansa up to 300 mtr 505 154 233 308 428 701 1894 5882 12388 6217 130 24122 20725 25508 32351 92

35 E Banaskantha Vav, Tharad,& Suigam up to 300 mtr 575 167 265 349 486 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92

36 F PatanSami, Harij, Radhanpur. Santalpur & Sankheshwar

up to 300 mtr638 196 292 392 544 701 1894 5882 12388 6217 128 23915 20725 25508 32351 92

37 D BanaskanthaBhabhar,Kankrej,Deodar,Deesa,Lakhani taluka Above

300 mtr583 179 270 359 496 701 1894 5882 12388 6217 0 26051 0 0 32351 103

38 E Ahmedabad Detroj, Mandal, Viramgam Above 300 mtr 586 180 270 359 497 701 1894 5882 12388 6217 0 26051 0 0 32351 103

39 E MehsanaMehsana,Kadi,Becharaji,Unjha,Gojarya,Jotana taluka

Above 300 mtr559 172 256 342 475 701 1894 5882 12388 6217 0 26051 0 0 32351 103

40 E PatanPatan,Chanasma,Saraswati,

Siddhapur taluka Above 300 mtr

569 173 263 348 484 701 1894 5882 12388 6217 0 26051 0 0 32351 103

41 E Banaskantha Vav, Tharad,Suigam Above 300 mtr 623 180 288 379 528 701 1894 5882 12388 6217 0 26051 0 0 32351 103

42 F PatanSami,Harij,Radhanpur,Santalpur,Sankheshwar Above

300 mtr721 222 330 443 613 701 1894 5882 12388 6217 0 26051 0 0 32351 103

SOR Mech 2019-20

Page 17 of 166

SECTION - "A"Sr

. No.

Grou

p

District TalukaApproved

Rate for SOR 2019-20

1 A Dahod Devgadhbaria,Dhanpur 274.40 2 B Dahod Limkheda 314.72 3 C Dahod Dahod,Jhalod,Fatepura,Garbada 245.28 4 A P'Mahal Halol,Jambugoda 312.48 5 B P'Mahal Goghamba 282.15 6 C P'Mahal Kalol 299.61 7 D P'Mahal Godhara 268.80 8 E P'Mahal Morva(Hadaf), 280.36 9 F P'Mahal Shahera 271.93

10 A Mahisagar Santarampur,Kadana 225.95 11 B Mahisagar Khanpur Lunavada 342.72 12 C Mahisagar Virpor & Balasinor 306.88 13 A Vadodara All Taluka 268.80 14 A C'Udepur All Taluka Except C'Udepur & Jetpurpavi 268.80 15 B C'Udepur Chhotaudepur & Jetpurpavi 312.48 16 C Surat Mandavi,Mangrol,Umarpada 222.88 17 C1 Surat Mahuva,Bardoli, Kamrej 246.08 18 D Tapi Songadh,Nizaar,Uchchhal 212.93 19 D1 Tapi Vyara,Valod 205.30 20 B Bharuch All Taluka 273.28 21 A Narmada Dediyapada & Sagbara 231.99 22 A1 Narmada Nadod & Tilakvada 328.00 23 B Dang All Taluka 243.26 24 A Navsari All Taluka 194.00 25 B Valsad Dharampur,Kaprada 243.66 26 C Valsad Valsad,Paradi,Vapi 235.83 27 C1 Valsad Umargham 248.94

Annexure-B1Approved Drilling of 165mm dia DTH SOR Rate 2019-20 For Zone-1


SECTION - "A"

Sr.No District UnitRate approved

for the year 2019-20

Ahmedabad

Banaskantha

Mehsana

Group-II Sabarkantha & Aravalli Mtr 299.04

Group-IIISabarkantha Mtr 360.64

Banaskantha

Mehsana

Group-V Kheda Mtr 309.63

Himmatnagar, Prantij, Talod, Vijaynagar Taluka.Aravalli - Modasa, Bhiloda, Meghraj, Malpur, Bayad, Dhansura Taluka

All Taluka

Vadnagar,Satlasan,Kheralu taluka

Khedbrahma,Vadali ,Idar taluka

357.28

379.68

Mtr

MtrDanta & Amirgadh taluka

Group-IV

Except Vadnagar,Satlasana,Kheralu taluka.

Except Danta,Amirghadh taluka

Annexure-B2Item No.2.2 for Zone-2

Approved Rate for Drilling of 165mm dia DTH for 2019-20

All Taluka

Taluka

PART-I 165 mm dia DTH bore

Group-I


SECTION - "A"

Sr.No District UnitRate approved

for the year 2019-20

Ahmedabad

Sabarkantha

Banaskantha

Mehsana

Group II Sabarkantha Mtr 585.76

Banaskantha Mtr

Mehsana Vadnagar,Satlasan,Kheralu taluka Mtr

Taluka

PART-II 200 mm dia DTH bore

Annexure-B3Item No.3.1 For Zone-2

Approved Rate for Drilling of 200mm dia DTH for 2019-20

536.48

507.36

All Taluka

MtrExcept Khedbrahma,Idar,Vadali & Poshina taluka

Except Danta,Amirghadh taluka

Khedbrahma,Poshina,Vadali ,Idar taluka

Except Vadnagar,Satlasana,Kheralu taluka.

Group-IIIDanta & Amirgadh taluka

Group-I


SECTION- B

Sr. No. Unit Approved Rate for 2019-20

1

a) 450 mm X 50 mm X 10 mm flat suitable to 32 mmdia. Pipe. per pair 353

b) 450 mm X 65 mm X 10 mm flat suitable to 50 mmdia.Pipe. per pair 534

c) 450 mm X 65 mm X 10 mm flat suitable to 65/80 mmdia.Pipe. per pair 542

d) 450 mm X 65 mm X 10 mm flat suitable to 100/125mm dia.Pipe. per pair 654

e) 750 mm X 75 mm X 10 mm flat suitable to 150 mmdia.Pipe. per pair 1053

f) 750 mm X 75 mm X 10 mm flat suitable to 175 mmdia.Pipe for Pipe lowering purpose. per pair 1065

g) 750 mm X 75 mm X 16 mm flat to 200 mm dia.Pipe. per pair 1550

h) 900 mm X 100 mm X 16 mm flat suitable for 250 mmdia.Pipe. per pair 1922

I) 900 mm X 100 mm X 16 mm flat suitable for 300 mmdia.Pipe. per pair 2157

2

A From 3 mm thick M.S. Plate (For top also.)

i Suitable for 100 mm dia pipe. No. 296

ii Suitable for 125 mm dia pipe. No. 336

iii Suitable for 150 mm dia pipe. No. 434

B From 5 thick M.S. Plate (For Top also)

SECTION- B (MATERIAL SECTION)

Bore plug having 100 mm height made from M.S. plate with 3holes at equal distance on circumference for nut-bolts type,locking arrangement with nuts-bolts & lock nuts of std. Makecomplete.

Description of Item

Clamp made from M.S. plate with 3 holes on either side withnuts & bolts of Std. Make and suitable size.

S.O.R. Mech 2019-20Page 21 of 166

SECTION- B

Sr. No. Unit Approved Rate for 2019-20Description of Item



iii Suitable for 250 mm dia pipe. No. 1095

C Bore plug having 100mm height made from UPVC ofstd. make



3

i) 150mm dia X 200 mm dia. X 600 mm length No. 1381

ii) 200mm dia X 250 mm dia. X 600 mm length. No. 1777

4-A

a) 150 mm dia pipe. No. 631

b) 200 mm dia pipe. No. 802

c) 250 mm dia pipe. No. 1004

d) 300 mm dia pipe. No. 1175

4-B



5

Supply of UPVC Bail plug (Bottom Cap) Suitable for

M.S. Bail plug having length 0.45 mtr from medium class pipeas per I.S.S. suitable for

Steel bent plate suitable to ERW pipe as detailed below

Reducer made from 6 mm thick plate (M.S.) for ERW pipesof size as below.

S.O.R. Mech 2019-20Page 22 of 166

SECTION- B


ERW Pipe Size in mm.

a) 150 mm dia 125 X 100 X 5 No. 32

b) 200 mm dia. 150 X 150 X 6 No. 63

c) 250 mm dia 200 X 150 X 6 No. 86

d) 300 mm dia 200 X 150 X 6 No. 86

a) Medium duty M.S. Coupling as per I.S. specification offollowing size.

i) 100 mm dia. No. 432

ii) 125 mm dia. No. 522

iii) 300 mm dia. No. 1652

b)Medium Duty 'B' class G.I. coupling as per I.S. 1239 )Part - II)/1990. --- 32 mm dia

No. 23

c) Heavy duty M.S. Coupling (8 mm thickness, 100 mmlength, 8 TPI thread as per IS)

i) 50mm dia 6mm Thick, 100mm Long No. 94

ii) 65mm dia 8mm Thick, 125mm Long No. 197

iii) 80mm dia 8mm Thick, 125mm Long No. 236

iv) 100mm dia 8mm Thick, 150mm Long No. 345

v) 125mm dia 8mm Thick, 150mm Long No. 417

vi) 150mm dia 8mm Thick, 150mm Long No. 502

7

a 200 mm dia ( Min 6.00 mm thick). Mtr. 1424

b 250 mm dia (Min.7.10 mm thickness) Mtr. 2112

Manufacture, supply and delivery of ISI marked ERW M.S. pipes conforming to IS: 4270/2001 with latest amendmentRates are exclusive of GST

6

S.O.R. Mech 2019-20Page 23 of 166

SECTION- B


a Normal Stand Assembly No. 5886

b Telescopic Stand Assembly No. 5900

c Extra Deepwell Handpumps set with 30 Nos of connecting rods. No. 10545

9

(A)A-1

No. 4.96

A-2No. 2.30

A-3No. 1.54

A-4No. 66.00

A-5No. 1.15

A-6No. 24.67

A-7No. 3.80

A-8No. 61.00

A-9No. 2.03

A-10No. 1634.00

(B)

B-1No. 4.25

Manufacturing of ISI marked Deepwell Handpumps set (IS 15500/2004 or any latest ammendment/revision there of) and supply & Delivery without riser pipes along with 12 Nos of connecting rods confirming to IS 1573 with latest amendment/revision.Rates are exclusive of GST

For Item No. 7: Above rates of Pipes are based on WPI Index(98.20) or HRC in month of (Aug-2017)

For Item No. 8 : Rates are taken as per RC Rates, approved in TPC-1 dated 19.12.2018.

8

Washer (4 mm thick) for Handle Axle

Bearing (No.6204-Z)

Spacer(for pump Head)

Chain with Coupling

Hexa. Bolts M-12x1.75x40mm long with Hexa.Nut M-12x1.75 & Washer 4mm thick

Hex. Bolt M10x1.50x40 mm long

Nylock Nut M10x1.50

Handle Axle(Stainless Steel)

SPARES FOR PUMP HEAD :

Supply of Different Hand Pump SparesRates are exclusive of GST.

Bolt for front cover M-12x20 mm long

Pump Head Assly.Consi.of Item No.(1) to (7) as per Fig.3.1

SPARES FOR CYLINDER

Pump Bucket

S.O.R. Mech 2019-20Page 24 of 166

SECTION- B


B-2No. 2.75

B-3No. 286.00

B-4No. 161.00

(C)No. 537.00

(D)No. 292.00

(E)No. 58.00

(F)

F-1 No. 5.90

(G)

G-1No. 1.40

G-2No. 89.00

G-3No. 69.00

G-4No. 83.90

G-5No. 72.98

G-6No. 38.00

(H)

H-1 No. 74.00

H-2 No. 53.00

H-3 No. 2.10

H-4 No. 29.30

Sealing Ring

Upper Valve Assly comp. consi.of item as per fig 3.6 A (Part no 1 to 4 & 8 to 9)

Lower Valve Assly comp.consi.of item as per fig 3.6 B (Part no 5 to 7 & 10)

WATER TANK consi.of item as per fig 3.6 B(1 to 6)

Cylinder With Brass Liner consi.of item (a) & (b)

REDUCER CAP

SPARES FOR CONECTING RODS

Hexagonal Coupler M-12 x 1.75 x 50 mm

UPPER VALVE SPARES.

Upper Valve Seating

Plunger Yoke Body

Bucket Spacer

Follower

Plunger Rod (S & S)

Upper Valve (Guide)

LOWER VALVE SPARES

Check Valve Seat.

Check Valve.

Check Valve Seating.

Rubber Seat Retainer

S.O.R. Mech 2019-20Page 25 of 166

SECTION- B


(I) No. 548.00

(J) No. 920.00

(K) No. 138.00

(L) No. 5580.00

M) No. 6290.00

(N) No. 126.60

(O)

O-1 No. 438.00

O-2 No. 1060.00

O-3 No. 475.00

O-4 No. 129.00

O-5 No. 69.00

10

A) 125 mm dia. LIGHT1) 1.00 mm Slot size Mtr. 7532) 1.50 mm Slot size Mtr. 697

B) 200 mm dia. REGULAR

1) 1.00mm Slot size Mtr. 1240

2) 1.50mm Slot size Mtr. 1146C) 250 mm dia REGULAR

1) 1.00mm Slot size Mtr. 18862) 1.50mm Slot size Mtr. 1747

D) 200 mm dia HEAVY1) 1.00mm Slot size Mtr. 14752) 1.50mm Slot size Mtr. 1366

E) 250 mm dia HEAVY1) 1.00mm Slot size Mtr. 2276

Handle Bar consisting of Item no (1) & (3) as per Fig 4.6

Cylinder Assly Comp.consisting of Item no (1) to (7) as per Fig 3.5

Conn. Rod Electro Galva.consisting of Item no (1) to (3) as per Fig 4.21

Special Tool Kit for I. M.-II Handpump consi. Item (1) to (11) as per IS 15500 Part-8 with tool box

Standerd Tool Kit for I. M.-II Handpump consi.Item(1) to (16) as per IS 15500 Part-8 with tool box

Third plate consisting of Item (1) & (2) as per fig 4.5

For Item No. 9: Rates are taken as per RC Rates, approved in TPC-1 dated 10.05.2018.

Spares for deep well Hand pump-Extra Deep

Cylinder Body with Brass Liner consisting of Item no (1) for body fig 5.2 & (2) for brass linear Fig 6.1 B

Handle Bar consisting of Item no (1) to (3) as per Fig 4.7

Upper Valve Assembly complete consisting of Item no (1) to (11) as per Fig 3.12

Follower as per Fig 6.7

Bucket Spacer-Lower as per Fig 6.5

Manufacture, supply and delivery of cage typeTrapezoidalshape ( ' V ') wire wound low carbon, Galvanized screen pipeand Stainless Steel Screen pipes, confirming IS: 8110Rates are exclusive of GST.

Low carbon, Galvanized screen pipe

S.O.R. Mech 2019-20Page 26 of 166

SECTION- B


2) 1.50mm Slot size Mtr. 2101

F) Stainless Steel Screen pipes.

1) 200 mm Dia 0.5 Slot size Mtr. 4075

2) 400 MM DIA Recharge pit screen 0.75 Slot size Mtr. 7786

3) 550 MM DIA Recharge pit screen 0.75 Slot size. Mtr. 10449

11

a 125.00 mm nominal dia " CM " Type Mtr. 355

b 200.00 mm nominal dia " CM " Type Mtr. 891

c 175.00 mm nominal dia " CS " Type Mtr. 559

12

1 0.6 M X 0.7 M x 0.4 M UNIT 4800

2 1.5 M X 1.0 M x 0.6 M UNIT 19356

3 1.5 M X 1.25 M x 0.6 M UNIT 22292

13 10670

Providing and fitting readymade prefabricated portableconcrete mini panel having outer size 110x50x190 cm withnecessary fitting for electric panel mounting complete as perdetailed specification and drawing.

A) Manufacturing supply & delivery of ISI marked (IS 12818 with latest amendment ).Rates are exclusive of GST


For Item No. 11: Rates are taken as per RC Rates, approved in TPC-1 dated 31.08.2018. Above rates of Pipes are based on PVC Resin of RIL, Grade 67ER092 (Rs.90093/MT including GST @ 18%) in month of (March-2018)

Providing dust and vermin proof Mild Steel Cabin having twocompartment one for panel board and other for GEB meterand fuse unit with required locking arrangement , minimumdegree of protection IP 52 as per IS 2147 fabricated fromCRCA sheer steel minimum thickness for baseframe/channel/gland plates for 3 mm for load bearingmembers ,1.6 mm for ineternal members includingcutting,bending,drilling,welding, riveting with ineternalpartitions.The sheet steel enclosure shall be powder coatedas per applicable standard with shade as required with finishthickness of paint film not less than 80 microns.The Cabinhave following dimension.

UPVC Casing pipe

S.O.R. Mech 2019-20Page 27 of 166

SECTION- B


i) DN 32 PN-10 Mtr. 31

ii) DN 40 PN-10 Mtr. 48

iii) DN 50 PN-10 Mtr. 73

iv) DN 63 PN-10 Mtr. 113

v) DN 63 PN-12.5 Mtr. 131

vi) DN 63 PN-16 Mtr. 157

vii) DN 90 PN-10 Mtr. 227

viii) DN 90 PN-16 Mtr. 319

ix) DN 110 PN-10 Mtr. 341

15(A)

1

Manufacture, Supply and Delivery of 50 mm Nominaldia UPVC Column Pipes including PVC Socket(Coupler), Density of Pipe 1.38 to 1.43 Gm per Cm3

OD : 59.50 TO 60.10 MM, Wall Thickness End : 6.10mm to 7.9mm, Berral : 3.9mm to 5.0mm, Length: 3Mtrs.

Mtr. 157

2Manufacture, Supply and Delivery of 50 mm size CIPipe Adaptor and Pump Adaptor for above 50 mm diacolumn Pippe.

Set 376

3


OD : 74.5 TO 75.2MM, Wall Thickness End : 9.0mm to10.70mm, Berral : 9.0mm to 10.70mm, Length: 3Mtrs.

Mtr. 221

4Manufacture, Supply and Delivery of 65 mm size CI Pipe Adaptor and Pump Adaptor for UPVC column Pipes

Set 581

UPVC Colmn Pipe. STANDRAD Duty Grade,175 mtrs,Head

Manufacture, Supply and delivery of following ISI markedH.D.P.E. Pipes (IS:4984/1985 with latest amendment) havingmaterial Grade PE-80 in approximate 100 mtr. Coil length oras per GWSSB requirement with SS-316 Nipple at both endhaving 11 TPI threading as per specification, press fitted andbolted having nominal diameter as under as per detailedTechnical Specification. Rates are based on IOCL Resin AGrade 45 GP 004DP44 as on dated 01.12.2017 Rs. 90284/-(Without GST)Rates are Exclusive of GST.

14


S.O.R. Mech 2019-20Page 28 of 166

SECTION- B


5


OD : 87.5 TO 88.2MM, Wall Thickness End : 9.8mm to11.9mm, Berral : 7.3mm to 9.0mm, Length:3Mtrs.

Mtr. 314

6Manufacture, Supply and Delivery of 80 mm size CIPipe Adaptor and Pump Adaptor forUPVC columnPipes.

Set 770

15(B) UPVC Column Pipes HEAVY Duty Grade, 250mtrs. Head

1

Manufacture, Supply and Delivery of 50 mm Nominal dia UPVC Column Pipes including PVC Socket (Coupler), Density of Pipe 1.38 to 1.43 Gm per Cm3, OD : 59.50 TO 60.10MM, Wall Thickness End : 6.10 nto 7.9mm, Berral : 3.9 to 5.0mm, Length:3 Mtrs.

Mtr. 200

2Manufacture, Supply and Delivery of 50 mm size CIPipe Adaptor and Pump Adaptor for UPVC columnPippe.

Set 376

3


OD : 74.5 TO 75.2MM, Wall Thickness End : 9.0mm to10.70mm, Berral : 9.0mm to 10.70mm, Length: 3 Mtrs.

Mtr. 301

4 Manufacture, Supply and Delivery of 65 mm size CIPipe Adaptor and Pump Adaptor for UPVCcolumn Pipes Set 581

5

Manufacture, Supply and Delivery of 80 mm Nominal dia UPVC Column Pipes including PVC Socket (Coupler), Density of Pipe 1.38 to 1.43 Gm per Cm3, OD : 87.5 TO 88.2MM, Wall Thickness End : 9.8mm to 11.9mm, Berral : 7.3mm to 9.0mm, Length: 3 Mtrs.

Mtr. 409

6Manufacture, Supply and Delivery of 80 mm size CIPipe Adaptor and Pump Adaptor for UPVC columnPipes.

Set 770

S.O.R. Mech 2019-20Page 29 of 166

SECTION- B


Supply and install heavy duty through the weave polyurethane(PU) covered hoses with coupling made from 100% high tencity synthetic yarn circular woven and completely embedded the PU compound,protected against mechanical damage, forming a single homogenous construction without the use of anu glues or adhesives of any type ,resistance to abrasion ,heat,oil,fuel,a wide range of chemicals , weathering and ozone,working pressure 8 kg/cm2 and burst pressure 20 kg/cm2.

A Fire Hose Pipe 100 MM dia Mtr. 1800

B Fire Hose Pipe 200 MM dia Mtr. 3600

C Fire Hose Pipe 300 MM dia Mtr. 5400

RO System

A

SS Skid mouted RO system as per IS:10500( latest) including Iron Removing Filter, Chloride & Flouride Removal Pump,raw water pump sand filter activated carbon ,dozing pump,micron filters,high pressuer pump,low-high presuer switchs,membrane housing,membrane,flow metters,pressuer gauges,electrical panal box,inter connection CPVC pipes,inernal electical wireing etc. CAPACITY : 500 LPH

Nos. 134560

B As Above.CAPACITY : 1000 LPH Nos. 200000

C As AboveCAPACITY : 2000 LPH Nos. 265000

GI FITTINGS ( Elbows, Nipple, Step Nipple,Union Plug Tee, Coupling,Reducer)

A) upto 65 MM Kg 72

B) Above 65 MM To 100 MM Kg 73C) Above 100 MM Kg 74

A) Supply of 300 mm dia RCC Plain pipes used in drilling ofRCC Tube wells Mtr. 380

B) Supply of 300 mm dia RCC Strainer pipes used in drillingof RCC Tube wells Mtr. 470

18

17

16

19

S.O.R. Mech 2019-20Page 30 of 166

SECTION - "C"

Sr. No Unit

1Per end With

CartingWithout Carting

a 150 mm dia per end 104.75 36.75

b 175 mm dia per end 108.50 40.50

c 200 mm dia per end 124.00 47.00

d 250 mm dia per end 160.00 54.00

e 300 mm dia per end 174.00 59.00

f 350 mm dia per end 197.30 72.00

a 200 mm dia Per Slot - 0.2271

b 250 mm dia Per Slot - 0.2420

c 300 mm dia Per Slot - 0.4129

a 200 mm dia per slot - 0.2313

b 250 mm dia per slot - 0.2621

c 300 mm dia per slot - 0.4342

3

a 150 mm dia thread length 65+5 mm per End - 113

2B

Approved Rate for 2019-20

2A

Description of Item

Gas cutting of M. S. / G. I. pipes of followingsize & facing pipe ends at right angles duly cutincluding carting of pipes (to & fro from localsub division stores to agency's workshop) andstacking the same as directed.

Facing of both ends of following size M. S. / G.I. column pipe & threading (8 TPI) with taperratio 1.25 & 550 thread angle including fitting ofcoupling on one end with requiredcircumferential welding. (including unloading ofpipes from truck & reloading pipes into truck).

Job work of slotting of M S ERW blind pipe offollowing size having slot size as 6.75 cm x 6.35cm x 3.12 mm (including unloading of blindpipes from truck & reloading slotted pipes intotruck).

As above having slot size as 6.75 cm x 6.35 cmx 1.59 mm.

"LABOUR ITEM"

S.O.R. Mech 2019-20

Page 31 of 166

SECTION - "C"

Sr. No Unit Approved Rate for 2019-20Description of Item

b 125 mm dia thread length 65+5 mm per End - 89

c 100 mm dia thread length 65+5 mm per End - 70

d 80 mm dia thread length 55+5 mm per End - 53

e 65 mm dia thread length 45+5 mm per End - 44

f 50 mm dia thread length 45+5 mm per End - 32

g 32 mm dia thread length 30+5 mm per End - 29

4(a) LS Job - 3635.00

(b) LS Job - 975.00

(c) LS Job - 2660.00

Construction of C. C. plateform 1:2:4 etc.including providing cement, sand & kapachi etc& construction of soak pit as modified Unicefdesign including excavation of (100 cm x 70 cmx 70 cm deep) with filling of stones, brokenbricks or gravel and laying 29 numbers bricksvertically on edge of soak pit etc. complete(Without carting).

Installation of India mark II H. P. assembly asper Unicef specifications complete with carting,lowering of 32 mm dia. riser pipes as required,construction of C. C. plateform 1:2:4 etc.including providing cement, sand & kapachi etc& construction of soak pit as modified Unicefdesign including excavation of (100 cm x 70 cmx 70 cm deep) with filling of stones, brokenbricks or gravel and laying 29 numbers bricksvertically on edge of soak pit etc. complete.

Installation of India mark II H. P. assembly asper Unicef specifications complete with carting,lowering of 32 mm riser pipes as required.

S.O.R. Mech 2019-20

Page 32 of 166

SECTION - "C"


(d) Job - 384.00

(e) Job - 197.60

(f) Job - 296.80

1 For Zone I Job - 485.00

2 For Zone II to V Job - 485.00

6(a)

Job - 10920.00

Job - 7800.00

Job - 5460.00

Job - 3120.00

Job - 2340.00

Removal of existing hand pump assembly withriser pipes from bore well & stacking themproperly by engaging required labour.

250 mm dia from GL to 6.0 mtr BGL.





Removal of existing damaged CC platform byengaging required labour.

Construction of soak pit as modified Unicef design including excavation of (100 cm x 70 cm x 70 cm deep) with filling of stones, broken bricks or gravel and laying 29 numbers bricks vertically on edge of soak pit etc. complete.

Annual overhauling, break down repairs,quarterly service of I.M. II H.P. of variousvillages of ______ Taluka & district (A) regular querterly service of each HP, (B)Breakdown repairing of HP on as and whenrequired basis and (C) Annual completeoverhauling (inclusive of bottom cylinder) ofeach HP As per Following Slab For All Districtof All Zone.

Jacking of pipes from failed tube well fromground level to 6 Mtr. BGL including by heavyduty power crane brought to site of work onrental basis for following size of pipe & cartingof recovered pipes from site to sub divisionalstore as directed.

5

S.O.R. Mech 2019-20

Page 33 of 166

SECTION - "C"


Job - 1092.00

6(b)

i) 300 mm dia RMT - 156.00

ii) 250 mm dia RMT - 125.00

iii) 200 mm dia RMT - 117.00

iv) 150 mm dia RMT - 109.00

v) 125 mm dia RMT - 94.00

vi) 100 mm dia RMT - 86.00

6(c) RMT - 83.00

7(a) Set - 12.00

(b)

i) 32 mm No. - 1.85

ii) 50 mm No. - 2.15

iii) 65 mm No. - 3.10

iv) 80 mm No. - 3.75

v) 100 mm No. - 4.65

vi) 125 mm No. - 6.20

(c)

Filling of existing failed tube well or finished bore hole of any size by sticky clay (With required materials)

Job work of loading of hand pump assembly complete into truck And / Or unloading and stacking the same in sub divisional store as directed.

Job work of loading of M S ERW / V Screen pipes of 4 to 7 meters length of following size into truck And / Or unloading and stacking the same in sub divisional store as directed.

Job work of loading of M S / G I column pipes of 3 meters length of following size into truck And / Or unloading and stacking the same in sub divisional store as directed.


Jacking of pipes from failed tube well futher from 6.00 meters BGL till recovery continues.

S.O.R. Mech 2019-20

Page 34 of 166

SECTION - "C"


i) 150 / 175 mm No. - 18.60

ii) 200 mm No. - 21.00

iii) 250 mm No. - 33.50

iv) 300 mm No. - 37.25

(d)

i 125 mm No. - 2.75

ii 175 mm No. - 7.00

iii 200 mm No. - 7.00

(e)

i 40 mm (100 mt long) No. - 16.75

ii 50 mm (100 mt long) No. - 22.25

iii 63 mm (100 mt long) No. - 22.25

iv 90 mm (100 mt long) No. - 44.75

v 110 mm (100 mt long) No. - 67.00

Job work of loading of HDPE pipe coil of following size into truck And / Or unloading and stacking the same in sub divisional store as directed.

Job work of loading of uPVC pipes of 3 meters length of following size into truck And / Or unloading and stacking the same in sub divisional store as directed.

S.O.R. Mech 2019-20

Page 35 of 166

SECTION - "C"


8

(a)

(b)

Providing light commercial (medium) four wheeler diesel vehicle on rental basis for one day (minimum 12 hours) (particularly for hand pump repairing works) with Driver & P.O.L. (The vehicle shall be fully insured with fitness certificate & PUC) Up to first 100 kms per day and extra km thereafter i. e. beyond 100 kms. Up to first 150 kms per day and extra km thereafter i. e. beyond 150 kms.

Day Km.

(a) 1500.00 Per Day

there after 10.00 per

km

(b) 1800.00 Per Day

there after 9.25 per km

9A

(a)

Providing light commercial (small) four wheeler diesel vehicle (Tata Ace "Chhota Hathi", Ashok Leyland "Dost", Mahindra "Utiliti" or equivalent) on rental basis for one day (minimum 12 hours) (particularly for hand pump repairing works) with Driver & P.O.L. (The vehicle shall be fully insured with fitness certificate & PUC) Up to first 100 kms per day and extra km thereafter i. e. beyond 100 kms.

Day Km.

900.00 Per Day there after 8.00

per km

9B

(a) (b)

Providing three wheeler diesel vehicle having carrier/ trolly (chhakada or equi.) on rent basis for entire day hiring (particular for hand pump repair works) With Driver, P.O.L., insurance, all RTO & toll tax etc.

Up to first 100 K.M. per Day Rate per Extra K.M. for more than 100 K.M. travelling

Day Km.

750 Per Day there after

6.50 per km

9C Hiring of vehicles for transportation of goods

i (a)(b)

Heavy Commercial Vehicle- Truck


Day Km.

2500 per day there

after 20.00 per km

S.O.R. Mech 2019-20

Page 36 of 166

SECTION - "C"


ii(a)(b)

Medium Commercial Vehicle- Eicher or equiv. Having carrier length not less than 6 meter


Day Km.

2000 per day there

after 15.00 per km

10 (A)

Hiring of Non AC Inspection vehicle (SUV) not older than 3 years (M & M: Bolero / Scorpio / Xuv; Tata: Sumo / Safari, Jeep or Equivalent) With Driver & P.O.L. (The vehicle shall have taxi passing with comprehensive full insurance, fitness certificate & PUC). Up to 2000 Kilometres / Monthand extra km thereafter i. e. beyond 2000 kms.

Fix Km.

21700

7.75/Km

10 (B)

Hiring of AC Inspection vehicle (SUV) not older than 3 years (M & M: Bolero / Scorpio / Xuv; Tata: Sumo / Safari, Jeep or Equivalent) With Driver & P.O.L. (The vehicle shall have taxi passing with comprehensive full insurance, fitness certificate & PUC) Up to 2000 Kilometres / Monthand extra km thereafter i. e. beyond 2000 kms.

Fix Km.

27999

10.48/Km

11 Rent of D.G.set Rs./day

FUEL-OIL-LUBRICANT

charges. Rs./ hr

Sr.No Capacity (KVA)

1 30 1156.40 417.72

Labour charges for hiring of D.G.Sets minimumfor 10 Days with maintainance & fuel charges ofvarious capacity from 30 KVA to 1000 KVA (440Volts) for operating pump & other equipments torun water supply scheme in different district inGujarat (the rates are inclusive of providingchange over switch & standard length cable &operating crew)

S.O.R. Mech 2019-20

Page 37 of 166

SECTION - "C"


2 40 1205.10 457.47

3 50 1332.80 580.72

4 62.5 1321.60 870.84

5 75 1345.50 1007.37

6 82.5 1404.20 1260.21

7 100 1593.00 1399.48

8 110 1591.20 1400.49

9 125 1654.10 1460.13

10 140 1947.00 2254.98

11 160 1989.00 2411.37

12 180 2284.80 2507.33

13 200 2324.60 2738.78

14 250 2421.90 3378.96

15 320 2701.30 4168.57

16 380 3150.60 4770.74

17 500 3814.20 5681.52

S.O.R. Mech 2019-20

Page 38 of 166

Section- "D"

Material Labour TotalPrevailing

rates of GST

Rates inclusive of GST

1

1.1

1.1.1

(a) Pt 270 60 330 -- 330

(b)Pt. 370 70 440 -- 440

(c) Pt. 240 40 280 -- 280

(d) Pt. 255 50 305 -- 305

(e) Pt 200 40 240 -- 240

1.1.2

(A)

(a) Pt. 240 50 290 -- 290

(b)Pt. 340 60 400 -- 400

(c) Pt. 210 40 250 -- 250

(d) Pt. 225 45 270 -- 270

(e) Pt. 170 40 210 -- 210

(B)

(a) Pt. 425 40 465 -- 465

(b)Pt. 505 50 555 -- 555

(c) Pt. 340 40 380 -- 380

(d) Pt. 405 40 445 -- 445

(e) Pt. 260 40 300 -- 300

(C)

(a) Pt. 520 50 570 -- 570

(b)Pt. 610 60 670 -- 670

(c) Pt. 460 50 510 -- 510

(d) Pt. 500 50 550 -- 550

(e) Pt. 360 50 410 -- 410

Sr. No.

Wiring

Description of Item

1. For Point wiring above 10 mtr. of length, additional length will be added at rate of mains.

Unit


2. For point wiring in bathroom and W/C and washbasin area in residential quarters reduce overall rate by 50% of point wiring for light.Point wiring in Copper (TISSINO)

Point wiring for Light/ Fan/ Bell/ Primary Point with 2-1.5 sq. mm & earthwire of 1.5 sq. mm (green) both are of ISI marked 1.1kV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in/ flushed on wall /ceiling, complete with 6A Tissino type ISI marked flush type switch/ bell push and accessories erected on Metal/ PVC Box covered with 3 mm thick PC (Polycarbonet)/ Acrylic sheet with necessary Lamp holder/ ceiling rose/ H.D.Connector as directed.

with medium class Rigid PVC pipe and accessories

with 16 swg(1.6 mm thick) HGS metal conduit pipe and accessories painted black

with oval conduit/ PVC casing capping double lock type

partial PVC pipe and drops in oval conduit/ PVC casing capping

in existing pipe

Point wiring for independent PLUG with following size mains & earthwire of 1.5 sq.mm (green) both are of ISI marked 1.1kV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in /flushed on wall/ ceiling, complete with ISI marked 3/5 Pin socket and tissino type switch erected with earth continuity connection erected on Metal/ PVC box covered with 3 mm thick PC (Polycarbonet)/ Acrylic sheet.

For 2-1.5 sq. mm Cu. Mains


with 16 swg HGS metal conduit pipe and accessories painted black



in existing pipe

6/16A Plug with 2-2.5 sq. mm Cu. Mains





in existing pipe

6/16A Plug with 2-4 sq.mm Cu. Mains





in existing pipe

S.O.R. Mech 2019-20Page 39 of 166

Section- "D"


rates of GST


Sr. No. Description of Item Unit


1.1.3

(A) Pt. 30 20 50 -- 50

(B) Pt. 120 30 150 -- 150

1.1.4

(A) Pt. 95 25 120 -- 120

(B) Pt. 150 30 180 -- 180

(C) Pt. 75 25 100 -- 100

(D) Pt. 85 25 110 -- 110

(E) Pt. 50 25 75 -- 75

1.1.5

(A) Pt. 290 60 350 -- 350

(B) Pt. 405 70 475 -- 475

(C) Pt. 270 40 310 -- 310

(D) Pt. 285 50 335 -- 335

(E) Pt. 220 40 260 -- 260

1.2

1.2.1

(a)Pt. 290 60 350 -- 350

Pt. 340 60 400 -- 400

Pt. 360 60 420 -- 420

(b)

Pt. 390 80 470 -- 470

Pt. 440 80 520 -- 520


Cat. I

Cat. II

Point wiring in Copper (Modular)

Point wiring for Light/ Bell with 2-1.5 sq. mm & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1kV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in/ on surface on wall/ ceiling complete with 6A Modular type switch/ bell push & accessories and earth continuity of following type, erected on PVC/ Metallic box, single mounting base frame covered with textured/ metallic front plate modules erected on/ in wall/ ceiling as per pipe erected, with necessary Lamp holder/ ceiling rose/ H.D.Connector as directed.


Cat. I

Cat. II

Cat. III

For 6 Amp.

For 16 Amp.

in existing pipe

Point wiring for secondary light point with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (green) both are of ISI marked 1.1kV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in/ flushed on wall/ ceiling, complete with earth continuity and necessary connection with primary light with accessories erected on Metal/ PVC box covered with 3 mm thick PC (Polycarbonet)/ Acrylic sheet for open/ concealed wiring with necessary Lamp holder/ ceiling rose/ H.D.Connector as directed.Note :- Maximum up to 6 mtrs length, excess will be considered as Mains for Secondary Point.





in existing pipe

Point wiring for Two way controlled Light Point with 2-1.5 sq.mm & earthwire of 1.5 sq. mm (green) both are of ISI marked 1.1kV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in/ flushed on wall/ ceiling complete with 6A Tissino type ISI marked accessories with earth continuity erected on Metal/ PVC box covered with 3 mm thick PC (Polycarbonet)/ Acrylic sheet with necessary Lamp holder/ ceiling rose/ H.D.Connector as directed.





Point wiring for looped PLUG with tissino type single pole ISI marked Switch and Socket erected with necessary connections erected on wooden/ Metal/ PVC Box covered with 3 mm thick PC (Polycarbonet)/ Acrylic sheet for open/ concealed wiring for following size.

S.O.R. Mech 2019-20Page 40 of 166

Section- "D"


rates of GST




Pt. 460 80 540 -- 540

( c)

Pt. 260 50 310 -- 310

Pt. 310 50 360 -- 360

Pt. 330 50 380 -- 380

(d)

Pt. 280 50 330 -- 330

Pt. 290 50 340 -- 340

Pt. 300 50 350 -- 350

(e) Pt. 220 50 270 -- 270

Pt. 270 50 320 -- 320

Pt. 300 50 350 -- 350

1.2.2

(a) Pt. 440 60 500 -- 500

Pt. 520 60 580 -- 580

Pt. 540 60 600 -- 600

(b)

Pt. 540 80 620 -- 620Pt. 620 80 700 -- 700Pt. 640 80 720 -- 720

( c)Pt. 400 50 450 -- 450Pt. 490 50 540 -- 540Pt. 510 50 560 -- 560

(d) Pt. 420 50 470 -- 470Pt. 470 50 520 -- 520Pt. 490 50 540 -- 540

(e) Pt. 360 50 410 -- 410Pt. 425 50 475 -- 475Pt. 440 50 490 -- 490

1.2.3

(A)

(a) Pt. 360 50 410 -- 410Pt. 380 50 430 -- 430

Cat. IIIPoint wiring for Individual Plug with earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1kV grade FRLS PVC insulated multistrand copper wires, in following type of to be erected concealed in/ on surface of wall/ ceiling complete with Modular type switch & 5 pin Plug erected on PVC/ Metallic box covered with appropriate front plate modules erected on/ in wall/ ceiling as per pipe erected with following type of accessories.

For 6A Plug with 2-1.5 sq.mm Cu. Wirewith medium class Rigid PVC pipe and accessories

Cat. ICat. II

Cat. ICat. IICat. IIIin existing pipeCat. ICat. II

Cat. IIIwith oval conduit/ PVC casing capping double lock type Cat. ICat. IICat. IIIpartial PVC pipe and drops in oval conduit/ PVC casing capping

Cat. I

Cat. II

Cat. III


Cat. ICat. II

in existing pipe

Cat. I

Cat. II

Cat. III

Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1kV Grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in/ flushed on wall/ ceiling complete with 6A Modular type switch and hume free EME four or more step type electronic fan regulator with separately mounted and accessories with earth continuity of following type erected on PVC/ Metallic box, single mounting base frame covered with textured/ metallic front plate modules erected on/ in wall/ ceiling as per pipe erected with necessary ceiling rose/ H.D.Connector as directed.


Cat. II

Cat. III


Cat. I

Cat. II

Cat. III

Cat. III


Cat. I

S.O.R. Mech 2019-20Page 41 of 166

Section- "D"


rates of GST




Pt. 395 50 445 -- 445

(b)

Pt. 460 60 520 -- 520Pt. 480 60 540 -- 540Pt. 495 60 555 -- 555

(c)

Pt. 330 40 370 -- 370Pt. 350 40 390 -- 390Pt. 365 40 405 -- 405

(d) Pt. 345 45 390 -- 390Pt. 365 45 410 -- 410Pt. 38 45 83 -- 83

(e)Pt. 290 40 330 -- 330Pt. 310 40 350 -- 350Pt. 325 40 365 -- 365

(B)(a)

Pt. 560 50 610 -- 610Pt. 595 50 645 -- 645Pt. 620 50 670 -- 670

(b)

Pt. 640 60 700 -- 700Pt. 680 60 740 -- 740Pt. 695 60 755 -- 755

(c)

Pt. 480 40 520 -- 520Pt. 520 40 560 -- 560Pt. 540 40 580 -- 580

(d)

Pt. 540 40 580 -- 580Pt. 580 40 620 -- 620Pt. 595 40 635 -- 635

(e)Pt. 395 40 435 -- 435Pt. 435 40 475 -- 475Pt. 460 40 500 -- 500

(C)(a)

Pt. 680 50 730 -- 730Pt. 720 50 770 -- 770Pt. 740 50 790 -- 790

(b)

Pt. 770 60 830 -- 830Pt. 800 60 860 -- 860Pt. 830 60 890 -- 890

(c)Pt. 620 50 670 -- 670Pt. 660 50 710 -- 710Pt. 680 50 730 -- 730

(d)

Pt. 660 50 710 -- 710Pt. 695 50 745 -- 745Pt. 720 50 770 -- 770

(e)Pt. 520 50 570 -- 570Pt. 560 50 610 -- 610Pt. 580 50 630 -- 630

Cat. IIIin existing pipeCat. ICat. IICat III

Cat. ICat. IICat. IIIpartial PVC pipe and drops in oval conduit/ PVC casing capping

Cat. ICat. II

Cat. IIIwith 16 swg HGS metal conduit pipe and accessories painted black

Cat. ICat. IICat. IIIwith oval conduit/ PVC casing capping double lock type

Cat. IICat IIIFor 16A Plug with 2-4 sq.mm Cu. Wirewith medium class Rigid PVC pipe and accessoriesCat. ICat. II


Cat. ICat. IICat. IIIin existing pipeCat. I

Cat. IICat. IIIwith oval conduit/ PVC casing capping double lock type

Cat. ICat. IICat. III

with medium class Rigid PVC pipe and accessoriesCat. ICat. IICat. IIIwith 16 swg HGS metal conduit pipe and accessories painted black

Cat. I

Cat. IIIin existing pipeCat. ICat. IICat. IIIFor 16A Plug with 2-2.5 sq.mm Cu. Wire


Cat. ICat. II

Cat. IIIwith 16 swg HGS metal conduit pipe and accessories painted black

Cat. ICat. IICat. IIIwith oval conduit/ PVC casing capping double lock type

S.O.R. Mech 2019-20Page 42 of 166

Section- "D"


rates of GST




1.2.4

Pt. 160 30 190 -- 190Pt. 190 30 220 -- 220Pt. 210 30 240 -- 240

1.2.5

(a)

Pt. 390 70 460 -- 460Pt. 440 70 510 -- 510Pt. 460 70 530 -- 530

(b)

Pt. 490 80 570 -- 570Pt. 540 80 620 -- 620Pt. 560 80 640 -- 640

(c)

Pt. 360 50 410 -- 410Pt. 410 50 460 -- 460Pt. 440 50 490 -- 490

(d)

Pt. 380 50 430 -- 430Pt. 390 50 440 -- 440Pt. 410 50 460 -- 460

(e)Pt. 320 50 370 -- 370Pt. 370 50 420 -- 420Pt. 400 50 450 -- 450

1.2.6

(A)Ea. 80 10 90 -- 90Ea. 115 10 125 -- 125Ea. 140 10 150 -- 150

(B)Ea. 80 10 90 -- 90Ea. 115 10 125 -- 125Ea. 140 10 150 -- 150

(C)(a)

Ea. 90 10 100 -- 100Ea. 120 10 130 -- 130Ea. 150 10 160 -- 160

(b)Ea. 120 10 130 -- 130Ea. 160 10 170 -- 170Ea. 200 10 210 -- 210

(D)Ea. 100 10 110 -- 110Ea. 130 10 140 -- 140Ea. 150 10 160 -- 160

(E)Ea. 280 10 290 -- 290

TV Co-axial socket outletCat.ICat.IICat.IIIElectronic hume free four or more steps EME fan regulator

Cat.I

Cat.IICat.IIIFor Two GangCat.ICat.IICat.III

Cat.ICat.IICat.IIITwo Pin/ RJ-11 telephone socketFor One GangCat.I

Providing following type of Modular type accessories mounted with PVC/ metallic box, single mounting base frame covered with textured/ metallic front plate, modules erected with necessary connection as desired by Engineer In charge

One No. SP 6 ACat.ICat.IICat.IIIOne No. 5 pin plug

Cat. IICat. IIIin existing pipeCat. ICat. IICat III



Cat. I

Cat. IICat. IIIwith 16 swg HGS metal conduit pipe and accessories painted black

Cat. ICat. IICat. III

Cat. ICat. IICat. IIIPoint wiring for two way controlled Light Point with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (green) both are of ISI marked 1.1kV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in/ flushed on wall/ ceiling, complete with 6A Modular type switches and following type of accessories erected on PVC/ Metallic box, single mounting base frame covered with textured/ metallic front plate modules erected on/ in wall/ ceiling as per pipe erected with necessary batten/ angle holder or ceiling rose or H.D.Connector as directed.


Cat. I

Point wiring for looped plug with 6A Modular type switch & 5 pin socket erected on PVC/ Metallic box, single mounting base frame covered with textured/ metallic front plate modules erected on/ in wall/ ceiling with following type accessories.

S.O.R. Mech 2019-20Page 43 of 166

Section- "D"


rates of GST




Ea. 330 10 340 -- 340Ea. 390 10 400 -- 400

(F)Ea. 90 10 100 -- 100Ea. 110 10 120 -- 120Ea. 170 10 180 -- 180

(G)Ea. 10 0 10 -- 10Ea. 15 0 15 -- 15Ea. 20 0 20 -- 20

(H)Ea. 100 10 110 -- 110Ea. 130 10 140 -- 140Ea. 150 10 160 -- 160

(I)Ea. 90 10 100 -- 100Ea. 120 10 130 -- 130Ea. 170 10 180 -- 180

(J)Ea. 110 10 120 -- 120Ea. 130 10 140 -- 140Ea. 190 10 200 -- 200

(K)Ea. 90 10 100 -- 100Ea. 100 10 110 -- 110Ea. 140 10 150 -- 150

(L)Ea. 110 10 120 -- 120Ea. 120 10 130 -- 130Ea. 160 10 170 -- 170

(M)Ea. 220 10 230 -- 230Ea. 260 10 270 -- 270Ea. 300 10 310 -- 310

(N)Ea. 300 10 310 -- 310Ea. 320 10 330 -- 330Ea. 400 10 410 -- 410

(O)Ea. 200 10 210 -- 210Ea. 220 10 230 -- 230Ea. 270 10 280 -- 280

(P)Ea. 280 10 290 -- 290Ea. 310 10 320 -- 320Ea. 350 10 360 -- 360

(a)Ea. 250 10 260 -- 260Ea. 310 10 320 -- 320

(b)Ea. 330 10 340 -- 340Ea. 390 10 400 -- 400

(c)Ea. 510 10 520 -- 520Ea. 590 10 600 -- 600

(Q)Ea. 150 10 160 -- 160Ea. 170 10 180 -- 180Ea. 230 10 240 -- 240

(R)Ea. 315 15 330 -- 330

(S)Ea. 115 15 130 -- 130Ea. 310 15 325 -- 325

(T)

(a) Ea. 450 50 500 -- 500(b) Ea. 650 50 700 -- 700equal of eight modules

Cat.IIIModular buzzerCat.IICat.IIIWhite Foot Light with concealed box, modular accessories, acrylic glass cover with suitable CFL 9/11/13 W LED lights

equal of four modules

Cat. III13 Amp. International modular socketCat.ICat.IICat.IIIModular indicating call bell

Cat. IIIFor 600 / 650 watt two module electronic dimmer Cat. IICat. IIIFor 1000 watt two module electronic dimmerCat. II

32 Amp. DP main switch operating with energy key ag Cat.ICat.IICat.IIIFor 400W / 450 watt One module electronic dimmerCat. II

Cat.IICat.III32 Amps. DP switch with indicatorCat.ICat.IICat.III

6A/ 10A/ 16A/ 20A/ 25A/ 32A single pole modular MCB switch Cat.ICat.IICat.III6A/ 10A/ 16A/ 20A/ 25A/ 32A double pole modular MCB switchCat.I

Cat.IICat.III6A/ 16A two way switch Cat.ICat.IICat.III

6A/ 16A Universal socketCat.ICat.IICat.III6 A Bell pushCat.I

Cat.IICat.III16 Amp. SP one way switchCat.ICat.IICat.III

Blank plate singleCat.ICat.IICat.IIIModem jack for computer open RJ-45Cat.I

Cat.IICat.IIIFuse units 10A/ 16ACat.ICat.IICat.III

S.O.R. Mech 2019-20Page 44 of 166

Section- "D"


rates of GST




(U)Ea. 370 30 400 -- 400Ea. 470 30 500 -- 500

1.3

1.3.1 Mtr. 0 10 10 -- 10

1.3.2

(a) Mtr. 18 5 23 -- 23(b) Mtr. 27 5 32 -- 32 (c) Mtr. 46 7 53 -- 53(d) Mtr. 59 8 67 -- 67

1.3.3

(a) Mtr. 22 3 25 -- 25(b) Mtr. 30 5 35 -- 35

1.3.4

(a) Mtr. 13 2 15 -- 15(b) Mtr. 18 2 20 -- 20(c) Mtr. 23 2 25 -- 25(d) Mtr. 33 2 35 -- 35(e) Mtr. 43 2 45 -- 45

1.3.5

(a) Mtr. 15 5 20 -- 20(b) Mtr. 25 5 30 -- 30(c) Mtr. 30 5 35 -- 35(d) Mtr. 35 5 40 -- 40

1.3.6

(a) Mtr. 260 20 280 -- 280(b) Mtr. 400 30 430 -- 430(B)(a) Ea 40 5 45 -- 45(b) Ea 60 5 65 -- 65(C)(a) Ea 70 5 75 -- 75(b) Ea 130 5 135 -- 135(D)(a) Ea 90 5 95 -- 95(b) Ea 110 5 115 -- 115(E)(a) Ea 70 5 75 -- 75(b) Ea 90 5 95 -- 95(F)(a) Ea 70 5 75 -- 75(b) Ea 90 5 95 -- 95(G)(a) Ea 70 5 75 -- 75(b) Ea 80 5 85 -- 85(H)(a) Ea 60 5 65 -- 65(b) Ea 75 5 80 -- 80(I)(a) Ea 30 0 30 -- 30

For one GangFor two GangUPVC TRUNKING DIVIDER For 50 mm (depth) trunking

For 75 mm x 50 mm trunking For100 mm x 50 mm trunking UPVC END CAP For 75 mm x 50 mm trunking For100 mm x 50 mm trunking SOCKET MOUNTING FRAME

For 75 mm x 50 mm trunking (2) For100 mm x 50 mm trunking UPVC INTERNAL BENDFor 75 mm x 50 mm trunking For100 mm x 50 mm trunking UPVC EXTERNAL BEND

For 75 mm x 50 mm trunking For100 mm x 50 mm trunking UPVC ELBOW For 75 mm x 50 mm trunking For100 mm x 50 mm trunking UPVC TEE

40 mmUPVC TRUNKING SYSTEM(A) Supplying and laying UPVC cable trunking system comprising unplasticised polyvinyl chloride rigid material with ignition free & flame proof confirming BS. All necessary accessories and measuring of following sizes.

75 mm x 50 mm trunking 100 mm x 50 mm trunking UPVC COUPLER

40 mm50 mmSupplying & erecting UPVC Mini trunking (PVC Casing-n-Capping) having double-locking arrangement with grooves, trunking of size not below 12.5 mm in height as per IS with accessories of PVC/ Resin polypropylene not below 1.8 mm thick duly sealed in joint & erected on wall/ ceiling of following size.

20 mm25 mm32 mm

20 mm25mmProviding & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes, Check-nuts etc. complete of following sizes.

20 mm25 mm32 mm

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/ in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following dia. of pipes in approved manner as directed. 20 mm25 mm32 mm40 mmProviding & erecting approved make OVAL CONDUIT with necessary fittings fixed with adhesive solution and suitable clamps erected on wall/ ceiling of following size.

16/20/25 Amp. Modular Starter for Motor / A.C. Unit CompleteCat.IICat.III Conduits & PipesFor Laying of pipes on stone wall add to the following item rate per meter

S.O.R. Mech 2019-20Page 45 of 166

Section- "D"


rates of GST




1.3.7

(a) Mtr 280 20 300 -- 300

(b) Mtr 360 20 380 -- 380

(c) Mtr 430 30 460 -- 460

(d) Mtr 940 40 980 -- 980

(e) Mtr 1010 40 1050 -- 1050

(f) Mtr 1180 50 1230 -- 1230

(g) Mtr 360 20 380 -- 380

(h) Mtr 440 20 460 -- 460

(i) Mtr 520 30 550 -- 550

(j) Mtr 730 40 770 -- 770

(k) Mtr 1060 40 1100 -- 1100

(l) Mtr 1160 40 1200 -- 1200

(m) Mtr 1300 50 1350 -- 1350

1.3.8

(a) Ea 2200 50 2250 -- 2250

(b) Ea 2530 70 2600 -- 2600

1.3.9

(a)Ea 4500 100 4600 -- 4600

(b) Ea 5300 100 5400 -- 5400

1.3.10

(a) Ea 950 50 1000 -- 1000(b) Ea 1380 70 1450 -- 1450(c) Ea 2150 100 2250 -- 2250(d) Ea 2400 100 2500 -- 2500(e) Ea 2850 150 3000 -- 3000

1.3.11

(a) Ea 50 10 60 -- 60(b) Ea 55 10 65 -- 65(c) Ea 65 10 75 -- 75(d) Ea 90 20 110 -- 110(e) Ea 105 20 125 -- 125(f) Ea 120 20 140 -- 140(g) Ea 55 10 65 -- 65(h) Ea 60 10 70 -- 70(i) Ea 70 10 80 -- 80(j) Ea 70 20 90 -- 90(k) Ea 105 20 125 -- 125(l) Ea 110 20 130 -- 130

(m) Ea 130 20 150 -- 150

100 x 38 x 1.6 mm for one compartments150 x 38 x 1.6 mm for Two compartments225 x 38 x 1.6 mm For Three Compartments250 x 38 x 1.6 mm for Three Compartments300 x 38 x 1.6 mm for Three Compartments

100 x 25 x 1.6mm for one compartments225 x 25 x 1.6 mm for three compartments250 x 25 x 1.6 mm for three compartments300 x 25 x 1.6 mm for three compartments50 x 38 x 1.6 mm for one compartments75 x 38 x 1.6 mm for one compartments

300mm x 300mm x 60/75 mm depth350mm x 350mm x 60/75 mm depth400mm x 400mm x 60/75 mm depthSupplying under floor trunking accessories joint sleeves for 25mm / 38mm pipe with following dimensions.50 x 25 x 1.6 mm for one compartments75 x 25 x 1.6 mm for one compartments

250mm x 250mm x 60/75 mm one trap three compartment (Metal lead)300mm x 300mm x 60/75 mm (Metal lead) Three Compartments

Junction BoxPVC/ GI Junction cross over box for metal/ Al. trunking with duct entry 25mm x 38mm size having epoxy powder coated trap lead with corrosion & rust free having load bearing capacity of 3.6 tons with adjustable levelling screw of following size.

150mm x 150mm x 60/75 mm depth250mm x 250mm x 60/75 mm depth

300mm x 38mm x 1.06 mm with Three Compartments

ACCESSOREIS FOR METAL TRUNCKINGunder floor metal vertical S.S. unit facilitate accessibility 25/ 38 mm height duct entry floor to wall & floor to floor.

250mm x 200mm x 50 mm for 2 Nos. compartments

300mm x 200mm x 50mm for 2 Nos Compartments

Floor mounted metal S.S. outlet (under floor service) made of high quality ABS & polyamide materials with trap frame & screw less ratchet trap lead with screw less knob reinforced with 2.5mm thick pregalvanised steel plate of following size.

50mm x 38mm x 1.6 mm with One Compartments

75mm x 38mm x 1.6 mm with one compartments

100mm x 38mm x 1.6 mm with One Compartments

150mm x 38mm x 1.6mm with Three Compartments



50mm x 25mm x 1.6 mm with One Compartment

75mm x 25mm x 1.6 mm with One Compartment

100mm x 25mm x 1.6 mm with one compartment

225mm x 25mm x 1.6 mm with Three Compartment



METAL TRUNKINGSupplying & laying under floor pregalvanised corrosion proof rectangular sheet steel cable trunking of 1.6 mm thick having with stand point load up to 1.33 ton & free from seepage of concrete of screed water having following size of dimensions and No of compartments (W x D x T)

S.O.R. Mech 2019-20Page 46 of 166

Section- "D"


rates of GST




1.3.12

(a) Mtr. 70 20 90 -- 90(b) Mtr. 90 20 110 -- 110(c) Mtr. 120 20 140 -- 140(d) Mtr. 200 30 230 -- 230(e) Mtr. 290 30 320 -- 3201.4

1.4.1

(A)(a) Mtr. 55 5 60 -- 60(b) Mtr. 75 5 80 -- 80(c) Mtr. 75 5 80 -- 80(d) Mtr. 95 5 100 -- 100(e) Mtr. 84 6 90 -- 90(f) Mtr. 119 6 125 -- 125(g) Mtr. 164 6 170 -- 170

(B)

(a) Mtr. 105 25 130 -- 130(b) Mtr. 130 25 155 -- 155(c) Mtr. 125 25 150 -- 150(d) Mtr. 150 25 175 -- 175(e) Mtr. 130 30 160 -- 160(f) Mtr. 165 30 195 -- 195(g) Mtr. 220 30 250 -- 250(C)(a) Mtr. 50 5 55 -- 55(b) Mtr. 75 5 80 -- 80(c) Mtr. 70 5 75 -- 75(d) Mtr. 90 5 95 -- 95(e) Mtr. 80 5 85 -- 85(f) Mtr. 114 6 120 -- 120(g) Mtr. 179 6 185 -- 185

(D)

(a) Mtr. 50 5 55 -- 55

(b) Mtr. 75 5 80 -- 80

(c) Mtr. 70 5 75 -- 75

(d) Mtr. 90 5 95 -- 95

(e) Mtr. 80 5 85 -- 85

(f) Mtr. 119 6 125 -- 125

(g) Mtr. 159 6 165 -- 165

(E)(a) Mtr. 42 3 45 -- 45

(b) Mtr. 57 3 60 -- 60

(c) Mtr. 55 5 60 -- 60

(d) Mtr. 85 5 90 -- 90

(e) Mtr. 74 6 80 -- 80

(f) Mtr. 109 6 115 -- 115

(g) Mtr. 149 6 155 -- 155

1.4.2

4 wire 2.5 sq. mm

6 wire 2.5 sq. mm

Mains with 1.1kV grade FRLS PVC insulated ISI marked stranded copper conductor wire in following type of pipe to be erected in/ on wall /ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size.

in existing pipe

2 wire 1.5 sq. mm

2 wire 2.5 sq. mm

3 wire 1.5 sq. mm

3 wire 2.5 sq. mm

4 wire 1.5 sq. mm

2 wire 2.5 sq. mm

3 wire 1.5 sq. mm

3 wire 2.5 sq. mm

4 wire 1.5 sq. mm

4 wire 2.5 sq. mm

6 wire 2.5 sq. mm

3 wire 2.5 sq. mm4 wire 1.5 sq. mm4 wire 2.5 sq. mm6 wire 2.5 sq. mmpartial PVC pipe and drops in oval conduit/ PVC casing capping

2 wire 1.5 sq. mm

2 wire 1.5 sq. mm2 wire 2.5 sq. mm3 wire 1.5 sq. mm

3 wire 1.5 sq. mm2 wire 2.5 sq. mm

Mains with 1.1kV grade FRLS PVC insulated ISI marked stranded copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ ceiling with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size. with medium class Rigid PVC pipe and accessories2 wire 1.5 sq. mm2 wire 2.5 sq. mm3 wire 1.5 sq. mm

3 wire 2.5 sq. mm4 wire 1.5 sq. mm4 wire 2.5 sq. mm6 wire 2.5 sq. mmwith oval conduit/ PVC casing capping double lock type

4 wire 1.5 sq. mm4 wire 2.5 sq. mm6 wire 2.5 sq. mmwith 16 swg HGS metal conduit pipe and accessories painted black

2 wire 1.5 sq. mm

3 wire 2.5 sq. mm

19/20 mm25 mm32 mm38/40 mm50 mmMains & Wires

Providing & erecting 16 gauge HGS conduit pipe (as per IS) painted black of following size complete to be erected on/ in wall or ceiling with erected with necessary saddles, screws, bends, junction boxes etc. with following (Nominal Bore) dia of pipes, in approved manner as directed

S.O.R. Mech 2019-20Page 47 of 166

Section- "D"


rates of GST




(A)(a) Mtr. 105 5 110 -- 110

(b) Mtr. 140 5 145 -- 145

(c) Mtr. 228 7 235 -- 235

(d) Mtr. 135 7 142 -- 142

(e) Mtr. 193 7 200 -- 200

(f) Mtr. 318 7 325 -- 325

(g) Mtr. 170 10 180 -- 180

(h) Mtr. 250 10 260 -- 260

(i) 415 10 425 -- 425

(B)

(a) Mtr. 150 25 175 -- 175

(b) Mtr. 190 25 215 -- 215

(c) Mtr. 275 25 300 -- 300

(d) Mtr. 180 25 205 -- 205

(e) Mtr. 245 25 270 -- 270

(f) Mtr. 370 25 395 -- 395

(g) Mtr. 205 30 235 -- 235

(h) Mtr. 300 30 330 -- 330

(i) 455 30 485 -- 485

(C)(a) Mtr. 90 5 95 -- 95

(b) Mtr. 130 5 135 -- 135

(c) Mtr. 218 7 225 -- 225

(d) Mtr. 125 7 132 -- 132

(e) Mtr. 188 7 195 -- 195

(f) Mtr. 313 7 320 -- 320

(g) Mtr. 160 10 170 -- 170

(h) Mtr. 245 10 255 -- 255

(i) Mtr. 405 10 415 -- 415

(D)

(a) Mtr. 100 5 105 -- 105

(b) Mtr. 135 5 140 -- 140

(c) Mtr. 223 7 230 -- 230

(d) Mtr. 133 7 140 -- 140

(e) Mtr. 203 7 210 -- 210

(f) Mtr. 323 7 330 -- 330

(g) Mtr. 165 10 175 -- 175

(h) Mtr. 255 10 265 -- 265

(i) Mtr. 415 10 425 -- 425

(E)(a) Mtr. 80 5 85 -- 85

(b) Mtr. 115 5 120 -- 120

(c) Mtr. 203 7 210 -- 210

(d) Mtr. 113 7 120 -- 120

(e) Mtr. 173 7 180 -- 180

(f) Mtr. 298 7 305 -- 305

(g) Mtr. 145 10 155 -- 155

(h) Mtr. 230 10 240 -- 240

3 wire 6 sq. mm

3 wire 10 sq. mm

4 wire 4 sq. mm

4 wire 6 sq. mm

4 wire 10 sq. mm

in existing pipe

2 wire 4 sq. mm

2 wire 6 sq. mm

2 wire 10 sq. mm

3 wire 4 sq. mm

2 wire 10 sq. mm

3 wire 4 sq. mm

3 wire 6 sq. mm

3 wire 10 sq. mm

4 wire 4 sq. mm

4 wire 6 sq. mm

4 wire 4 sq. mm

4 wire 6 sq. mm

4 wire 10 sq. mm


2 wire 4 sq. mm

2 wire 6 sq. mm

2 wire 4 sq. mm

2 wire 6 sq. mm

2 wire 10 sq. mm

3 wire 4 sq. mm

3 wire 6 sq. mm

3 wire 10 sq. mm

3 wire 6 sq. mm

3 wire 10 sq. mm

4 wire 4 sq. mm

4 wire 6 sq. mm

4 wire 10 sq. mm


4 wire 10 sq. mm

with 16 swg HGS metal conduit pipe and accessories painted black2 wire 4 sq. mm

2 wire 6 sq. mm

2 wire 10 sq. mm

3 wire 4 sq. mm

2 wire 10 sq. mm

3 wire 4 sq. mm

3 wire 6 sq. mm

3 wire 10 sq. mm

4 wire 4 sq. mm

4 wire 6 sq. mm

with medium class Rigid PVC pipe and accessories2 wire 4 sq. mm

2 wire 6 sq. mm

S.O.R. Mech 2019-20Page 48 of 166

Section- "D"


rates of GST




(i) Mtr. 390 10 400 -- 400

1.4.3

(a) Mtr 17 3 20 20

(b) Mtr 24 3 27 -- 27

(c) Mtr 45 5 50 -- 50

(d) Mtr 65 5 70 -- 70

(e) Mtr 95 5 100 -- 100

(f) Mtr 130 10 140 -- 140

(g) Mtr 210 10 220 -- 220

(h) Mtr 45 5 50 -- 50

(i) Mtr 60 5 65 -- 65

(j) Mtr 95 5 100 -- 100

(k) Mtr 130 10 140 -- 140

(l) Mtr 45 5 50 -- 50

(m) Mtr 75 5 80 -- 80

(n) Mtr 120 5 125 -- 125

(o) Mtr 170 10 180 -- 180

1.4.4

(a) Mtr. 9 1 10 -- 10

(b) Mtr. 14 1 15 -- 15

(c) Mtr. 23 2 25 -- 25

(d) Mtr. 33 2 35 -- 35

(e) Mtr. 53 2 55 -- 55

(f) Mtr. 88 2 90 -- 90

(g) Mtr. 137 3 140 -- 140

(h) Mtr. 232 3 235 -- 235

(i) Mtr. 297 3 300 -- 300

(j) Mtr. 464 6 470 -- 470

(k) Mtr. 664 6 670 -- 670

(l) Mtr. 908 12 920 -- 920

(m) Mtr. 1168 12 1180 -- 1180

(n) Mtr. 1450 15 1465 -- 1465

1.4.5

(a) Mtr. 11 1 12 -- 12

(b) Mtr. 13 1 14 -- 14

(c) Mtr. 19 1 20 -- 20

(d) Mtr. 29 1 30 -- 30

(e) Mtr. 44 1 45 -- 45

(f) Mtr. 64 1 65 -- 65

(g) Mtr. 54 1 55 -- 55

(h) Mtr. 74 1 75 -- 75

(i) Mtr. 104 1 105 -- 105

(j) Mtr. 123 2 125 -- 125

1.50 Sq.mm 4 core round PVC sheathed





Supplying and erecting Flexible PVC insulated multistrand multicore 1.1kV grade ISI marked copper wires of following size to be erected as directed.0.75 Sq.mm twin twisted

1.00 Sq.mm twin twisted

1.00 Sq.mm 2 core round/ flat PVC sheathed



One wire 35.00 sq. mm












4 wire 1.5 sq.mm

4 wire 2.5 sq.mm

4 wire 4.0 sq.mm

Mains with ISI marked, 1.5kV grade electrolyte multi stranded, annealed copper conductor with heat resistant PVC insulated conforms to IS 694, IEC-227 erected in existing pipe of following size (Specifically for control panel, relays, power switchgears, motor starters & control wiring) with required size of copper lugs, nuts and bolts if required.One wire 1.00 sq. mm


2 wire 10.0 sq.mm

3 wire 1.0 sq.mm

3 wire 1.5 sq.mm

3 wire 2.5 sq.mm

3 wire 4.0 sq.mm

4 wire 1.0 sq.mm

2wire 0.75 sq.mm (w/o ECC)

2 wire 1.0 sq.mm (w/o ECC)

2 wire 1.5 sq.mm

2 wire 2.5 sq.mm

2 wire 4.0 sq.mm

2 wire 6.0 sq.mm

4 wire 10 sq. mm

Mains with ISI marked electrolyte stranded copper conductor, Non PVC Zero Halogen free fire retardant insulated copper conductor, insulated wire (HFFR) conforms to IS-694, erected in existing pipe with 1.5 sq. mm copper conductor of same specifications for earth continuity of following size.

S.O.R. Mech 2019-20Page 49 of 166

Section- "D"


rates of GST




(k) Mtr. 173 2 175 -- 175

1.4.6

(a) Mtr. 16 1 17 -- 17

(b) Mtr. 29 1 30 -- 30

(c) Mtr. 14 1 15 -- 15

(d) Mtr 24 1 25 -- 25

(e) Mtr. 44 1 45 -- 45

1.4.7

(A)(a) Mtr. 7 2 9 -- 9

(b) Mtr. 12 2 14 -- 14

(c) Mtr. 17 2 19 -- 19

(d) Mtr. 28 2 30 -- 30

(e) Mtr. 48 2 50 -- 50

(f) Mtr. 98 2 100 -- 100

(B)(a) Mtr. 94 6 100 -- 100

(b) Mtr. 148 12 160 -- 160

(c) Mtr. 370 20 390 -- 390

(d) Mtr. 670 35 705 -- 705

1.4.8

(a) Mtr 25 5 30 -- 30

(b) Mtr 60 5 65 -- 65

(c) Mtr 35 5 40 -- 40

(d) Mtr 65 5 70 -- 70

1.4.9

(a) Ea. 550 50 600 -- 600

(b) Ea. 950 50 1000 -- 1000

(c) Ea. 1450 50 1500 -- 1500

1.5

1.5.1

(a) Ea. 35 10 45 -- 45

(b) Ea. 65 10 75 -- 75

(c) Ea. 75 12 87 -- 87

(d) Ea. 95 15 110 -- 110

1.5.2Sq. Inch

1 0.5 1.50 -- 2

1.5.3Sq.

Inch.1 0.5 1.5 -- 2

1.6

Providing & Erecting 3mm thick acrylic Sheet with grooving as directed Wiring Accessories

Supplying & erecting MS Box having 16 Gauge painted with red oxide or Heavy duty PVC box erected flushed on wall or concealed in wall with necessary plastering & finishing as directed of following size.100 mm x 100 mm x 75 mm(d)

175 mm x 100 mm x 75 mm(d)

200 mm x 250 mm x 75 mm(d)

250 mm x 300 mm x 75 mm(d)

Providing & Erecting 3mm thick Polycarbonate (PC) sheet with grooving as directed

CAT - 6e

Providing & erecting main Distribution (MDF) indoor type, back mounted frame.Suitable for 10 pair

Suitable for 20 pair

Suitable for 50 pair

Concealed Boxes & Laminated Sheets

Fifty Pairs

One Hundred Pairs

Supplying & erecting approved make LAN cable of following size in existing pipe as per directionCAT - 5

CAT - 5e

CAT - 6

Five Pairs

Ten Pairs

Twenty Pairs

Armoured [Jelly Filled]

Ten Pairs

Twenty Pairs

Supplying & erecting Delton or approved make telephone cable electrolytic copper conductor PE insulation twisted in two pairs, & wrapped with FRLS PVC tape & sheathed with FRLS PVC or HFFR outer Jacket suitable for telephone wiring & confirming to C-DOT erected in existing pipe of following size of conductors & nos. of pairs with necessary connections.

Conductor Size 0.5 mm

Unarmoured

One Pair

Two Pairs

Three Pairs

Providing & Erecting approved make following size of TV Co-axial flexible cable comprising inner conductor of solid bare copper insulated with Foam PE & Secondary conductor made of poly - Aluminium film bonded Al. Braids @ suitable coverage overall sheathed with black PVC insulation.

RG 59

RG-6

RG - 6 CCS

RG - 11 CCS

RG-11

4.00Sq.mm 4 core round PVC sheathed

S.O.R. Mech 2019-20Page 50 of 166

Section- "D"


rates of GST




1.6.1

(a) Ea. 25 5 30 -- 30

(b) Ea. 25 5 30 -- 30

(c) Ea. 40 5 45 -- 45

(d) Ea. 40 5 45 -- 45

(e)Ea. 80 15 95 -- 95

(f)Ea. 110 15 125 -- 125

(g) Ea. 10 5 15 -- 15

(h) Ea. 15 5 20 -- 20

(i) Ea. 35 5 40 -- 40

(j) Ea. 35 5 40 -- 40

(k) Ea. 15 5 20 -- 20

(l) Ea. 25 5 30 -- 30

(m) Ea. 25 5 30 -- 30

(n) Ea. 207 13 220 -- 220

1.6.2

(a) Ea. 300 35 335 -- 335

(b)Ea. 830 60 890 -- 890

Ea. 980 60 1040 -- 1040

Ea. 1080 60 1140 -- 1140

1.6.3 Ea. 6 2 8 -- 8

1.6.4 Ea. 6 0 6 -- 6

1.6.4Ea. 12 3 15 -- 15

1-6-6. Ea. 22 3 25 -- 25

1.6.7 Ea. 40 5 45 -- 45

1.6.8Ea. 18 2 20 -- 20

Ea. 28 2 30 -- 30

1.6.9Ea. 130 20 150 -- 150

1.6.10 Ea. 25 5 30 -- 30

1.6.11Ea. 35 5 40 -- 40

1.6.12Ea. 64 6 70 -- 70

1.6.13Ea. 250 0 250 -- 250

1.6.14Ea. 650 50 700 -- 700

1.6.15Ea. 15 0 15 -- 15

Supplying & erecting approved make call bell indicator with buzzing sound and red light indicating lamp with red light button to attend the call suitable for 240V, 50c/s supply to be erected.Call bell/ buzzer 250 volts, complete erected

Providing automatic staircase unit and light control switch with photocell & solid state circuits with loading capacity up to 1000 Watt

Supplying electrical insulation LT tape role with ISI marked having nominal width 1.8cms nominal length 9.0mtr nominal thickness 0.125mm and having self adhesive PVC

Hanging bed switch/ bell push 5A erected on existing flexible wire

5A, 10 way bakelite connector duly erected on existing board

15A, 10 way bakelite connector duly erected on existing board

Providing & erecting ISI marked 3 pin plug top

(a) for 5/6 A., 240V

(b) for 15/16A, 240V

For Tissino Type Accessories

For Modular Type Accessories

Cat. I

Call bell gong type suitable for 230 volts, 50 c/s AC supply complete erected Decorative call bell ting-tong box type 250 volts complete erected

Supplying & erecting electronic type cordless call bell erected on PVC/ Metal board having portable bell push working on DC & bell on 230V AC supply with cells/ battery.

Cat. II

Cat. III

Bakelite adopter for holder to be erected

Starter for 20 watts/ 40 watts fluorescent tube

Jack type tissino Telephone outlet

Tissino type Neon ‘Indicator Lamp’

Tissino type TV antenna socket

Tissino type 10A/16A Kitkat fuse

Electronic hume free EME socket type steps fan regulator

Providing & erecting switch board for computer or electric apparatus consisting of following items in single board erected on PVC/ Metal board with 3mm thick PC (Polycarbonate)/ Acrylic sheet erected as directed 1 no. 6A/16A universal plug-switch combined.4 nos. 6A switch4 nos. 6A 5 pin plug

One no 6/16A Universal Socket

One no single pole 16A switch & One no 6/16A Universal Socket combined One no single pole 16A switch & One no 6A/16A Universal Socket combined with indicator & fuseBakelite ceiling, rose

Bakelite lamp holder

Telephone Pin, Socket with suitable top

Providing & Erecting following shockproof tissino type accessories erected on 3mm thick PC (Polycarbonate) sheet in PVC/ Metal Box erected on wall/ ceiling.

One no single pole 6A switch/ bell push

One no 3/5 pin 6A socket

One no single pole 16A switch

S.O.R. Mech 2019-20Page 51 of 166

Section- "D"


rates of GST




1.7

1.7.1

Ea. 10800 0 10800 -- 10800

1.7.2

Ea. 14100 0 14100 -- 14100

1.7.3

Ea. 18400 0 18400 -- 18400

1.7.4

Ea. 22600 0 22600 -- 22600

1.7.5

Ea. 16500 0 16500 -- 16500

1.7.6

Ea. 22000 0 22000 -- 22000

1.7.7

Ea. 26000 0 26000 -- 26000

Supply of Fibreglass Step (A Type) Ladder- 8 FT having following specifications:It should have nonconductive structural moulded top with slots to keep tools close at hand, inside spreader braces, aluminium feet with thick rubber tread, nonconductive full channel fibreglass and two pairs of gusset support at the bottom step. All gussets are heavy duty steel.Capacity: 300 lbs. , Step Size: 3”, Width: 26” Approx. , Spread: 54” Approx., Wt.: 15 Kg Approx. , Cube: 9.5Supply of Fibreglass Step (A Type) Ladder- 10 FT having following specifications:It should have nonconductive structural moulded top with slots to keep tools close at hand, inside spreader braces, aluminium feet with thick rubber tread, nonconductive full channel fibreglass, two pairs of gusset support at the bottom step. All gussets are heavy duty steel.Capacity: 300 lbs, Step Size: 3”, Width: 29” Approx., Spread: 66” Approx. , Wt.: 19 Kg Approx., Cube: 12.54’

Supply of Fiberglas Step (A Type) Ladder- 4 FT having following specifications.It should have nonconductive structural moulded top, with slots to keep tools close at hand, inside spreader braces, aluminium feet with thick rubber tread, nonconductive full channel fibreglass and two pairs of gusset support at the bottom step. All gussets are heavy duty steel.Capacity: 300 lbs., Step Size: 3”, Width: 19” Approx. , Spread: 29” Approx., Wt.:8Kg Approx. , Cube: 4.05’

Supply of Fibreglass Step Trestle (A Type) Ladder- 6 FT having following specifications:It should have heavy gauge steel hinges suitable for industrial application, inside spreader braces, aluminium feet with thick rubber tread, nonconductive full channel fiberglass, two pairs of gusset support at the bottom step. All gussets are heavy duty steel. It should have steps on both the sides for climbing. Capacity: 300 lbs.Step Width: 3”, Bottom Width:23” Approx. , Spread : 52”Approx.Wt.:13 Kg, Approx. Cube : 6.53’

Supply of Fibreglass Step Trestle (A Type) Ladder- 8 FT having following specifications:It should have heavy gauge steel hinges suitable for industrial application, inside spreader braces, aluminium feet with thick rubber tread, nonconductive full channel fibreglass, two pairs of gusset support at the bottom step. All gussets are heavy duty steel. It should have steps on both the sides for climbing. Capacity: 300 lbs., Step Width: 3”, Bottom Width: 26” Approx. Spread: 67” Approx. , Wt.: 20 Kg Approx. , Cube: 9.51’Supply of Fibreglass Step Trestle (A Type) Ladder- 10 FT having following specifications:It should have heavy gauge steel hinges suitable for industrial application, inside spreader braces, aluminium feet with thick rubber tread, nonconductive full channel fibreglass, two pairs of gusset support at the bottom step. All gussets are heavy duty steel. It should have steps on both the sides for climbing. Capacity: 300 lbs., Step Width: 4”, Bottom Width: 29” Approx. Spread: 83” Approx. , Wt.: 27 Kg Approx., Cube: 13.44’

LADDERS

Supply of Fibreglass Step (A Type) Ladder- 6 FT having following specifications:It should have nonconductive structural moulded top with slots to keep tools close at hand, inside spreader braces, aluminium feet with thick rubber tread, nonconductive full channel fibreglass and two pairs of gusset support at the bottom step. All gussets are heavy duty steel.Capacity: 300 lbs. , Step Size: 3”, Width: 23” Approx. , Spread: 41” Approx. , Wt.: 11Kg Approx. , Cube : 6.2’

S.O.R. Mech 2019-20Page 52 of 166

Section- "D"


rates of GST




1.7.8

Ea. 19600 0 19600 -- 19600

1.7.9

Ea. 24000 0 24000 -- 24000

1.7.10

Ea. 28300 0 28300 -- 28300

2.1

2.1.1 Ea. 433 0 433 12% 485

2.1.2 Ea. 577 0 577 12% 646

2.1.3 Ea. 613 0 613 12% 687

2.2

2.2.1Ea. 217 0 217 18% 256

2.2.2Ea. 325 0 325 18% 384

2.2.3

(a) Ea. 866 0 866 18% 1022

(b) Ea. 945 0 945 18% 1115

2.2.4

(a) Ea. 758 0 758 18% 894

(b) Ea. 1010 0 1010 18% 1192

2.2.5

(a) Ea. 1803 0 1803 12% 2019

(b) Ea. 2452 0 2452 12% 2746

(c) Ea. 3029 0 3029 12% 3392

2.2.6

(a) Ea. 2019 0 2019 12% 2261

(b) Ea. 3245 0 3245 12% 3634

(c) Ea. 3389 0 3389 12% 3796

2.2.7

Ea. 1190 0 1190 12% 1333

Ea. 2452 0 2452 12% 2746

With 20 watt LED lamp


With 1 x 18 watt LED lamp

With 1 x 36 watt LED lamp


Supplying and erecting R&B approved make of LED Weatherproof tubelight fixture with tube


With 18/ 20 watt LED lamp

Supplying and erecting R&B approved make of LED recessed mounted luminaire with rear reflector suitable for office and laboratory applications


Supplying and erecting R&B approved make of LED Suraface mounted luminaire with rear reflector suitable for office and laboratory applications



Supplying and erecting R&B approved make of LED batten for multipurpose application made from polycarbonate housing with 1 x 9/ 18/ 21W T8 with all accessories

Supplying and erecting R&B approved make of LED batten for multipurpose application made from polycarbonate housing with 2 x 9/ 18/ 21W T8 with all accessoriesSupplying and erecting approved R&B make of LED Downlighter recessed mounted for Indoor application

Supplying and erecting R&B approved make of LED Downlighter surface mounted for Indoor application


With 18/ 20 watt LED lamp

LED Lamp & Tubes R&B Approved make LED tube- 9 watt

2. Lamps & Fittings

R&B Approved make LED tube- 21 watt

LED Light fixture

R&B Approved make LED tube- 18 watt

Supply of Fibreglass Platform Step (A Type) Ladder- 10 FT having following specifications:It should have large fully serrated platform 15” wide 20” deep which locks ladder, aluminium feet with thick rubber tread, top rail guard to serve as a railing, two pairs of gusset support at the bottom step. All gussets are heavy duty steel. Capacity: 300 lbs. , Step Width: 4’ Approx. , Spread: 75”, Width: 32” Approx. , Wt.: 29 Kg Approx. , Cube: 15.31

Supply of Fibreglass Platform Step (A Type) Ladder- 6 FT having following specifications:It should have large fully serrated platform 15” wide 20” deep which locks ladder, aluminium feet with thick rubber tread, top rail guard to serve as a railing, two pairs of gusset support at the bottom step. All gussets are heavy duty steel. Capacity: 300 lbs., Step Width: 3’ Approx. , Spread: 50” , Width: 26.5” Approx. , Wt.: 16 Kg Approx. , Cube: 8.15’"

Supply of Fibreglass Platform Step (A Type) Ladder- 8 FT having following specifications:It should have large fully serrated platform 15” wide 20” deep which locks ladder, aluminium feet with thick rubber tread, top rail guard to serve as a railing, two pairs of gusset support at the bottom step. All gussets are heavy duty steel. Capacity: 300 lbs., Step Width: 3’ Approx., Spread: 62” , Width: 29.5” Approx., Wt.: 22 Kg Approx., Cube: 11.62

S.O.R. Mech 2019-20Page 53 of 166

Section- "D"


rates of GST




2.2.8Ea. 1154 0 1154 12% 1292

2.3

2.3.1

(a) Ea. 2740 0 2740 12% 3069

(b) Ea. 3966 0 3966 12% 4442

2.3.2

(a) Ea. 9734 0 9734 12% 10902

(b) Ea. 12978 0 12978 12% 14535

2.3.3

(a) Ea. 8292 0 8292 12% 9287

(b) Ea. 9734 0 9734 12% 10902

2.3.4

(a) Ea. 8292 0 8292 12% 9287

(b) Ea. 10815 0 10815 12% 12113

(c) Ea. 8292 0 8292 12% 9287

(d) Ea. 8292 0 8292 12% 9287

2.4

2.4.1Ea. 3389 0 3389 12% 3796

2.4.2Ea. 4038 0 4038 12% 4523

2.5

2.5.1 Ea. 44 0 44 12% 49

2.5.2 Ea. 57 0 57 12% 64

2.5.3 Ea. 67 0 67 12% 75

2.5.4 Ea. 73 0 73 12% 82

2.5.5 Ea. 124 0 124 12% 139

2.6

2.6.1

(a) Ea. 4687 0 4687 12% 5249

(b) Ea. 6850 0 6850 12% 7672

(c) Ea. 8652 0 8652 12% 9690

2.6.2

(a) Ea. 30138 0 30138 12% 33755

(b) Ea. 42395 0 42395 12% 47482

(c) Ea. 89116 0 89116 12% 99810

(d) Ea. 101157 0 101157 12% 113296

2.6.3

(a) Ea. 182413 0 182413 12% 204303

(b) Ea. 221347 0 221347 12% 247909

3 SWITCHGEARS & DISTRIBUTION BOARDS

3.1

with 3 x 33W Flood light, 8M High Pole

with 3 x 45W Flood light, 10M High Pole

BUSBAR CHAMBERS

Supplying and erecting R&B approved make, standalone solar LED street light system with tubular pole, polyacryline PV panel solar tubular battery. Battery box pole and mechanical hardwareWith 15 watt LED lamp


Supplying and erecting R&B approved make, standalone solar LED mini mast system with tubular pole, polyacryline PV panel solar tubular battery. Battery box pole and mechanical hardware.



R&B Approved make 18 watt compact fluorescent lamp

Street Lighting & Solar Lighting



R&B Approved make street light luminaire with one no suitable for- LED lamp complete with alluminium PDC housing toughened glass with cover IP 66 Protection.With 70 watt LED lamp

Supplying and erecting approved make, 6 Watt LED Wall light tri ngular down and up-downFlourocent tubes



R&B Approved make fluorescent tube (T8) 60 cms. 18/ 20 watt

R&B Approved make fluorescent tube (T8) 60 cms. 36 watt



Landscape Lighting Supplying and erecting R&B approved make watertight, integral flying saucer type post top lantern IP 65, suitable for 25 Watt LED lamp, with other necessary accessories.



With 90 watt LED Lamp



Providing and erecting heavy duty flood light Luminaire with High Pressure die Cast Housing with IP 65.

Supplying and erecting industrial LED mid bay luminaire front toughened glass with discreate high power.With 80 watt LED Lamp

Supplying and erecting R&B approved make of 10 watt LED Bulkhead luminaire with diffuserIndustrial Lighting


Supplying and erecting industrial LED high bay luminaire front toughened glass with discreate high power.

Supplying and erecting LED wellglass with die cast alluminium housing with polycarbonate cover robust construction industrial type fitting with IP-66 Protection.


S.O.R. Mech 2019-20Page 54 of 166

Section- "D"


rates of GST




3.1.1

(a) Rmt 2600 160 2760 -- 2760

(b) Rmt 3050 200 3250 -- 3250

(c) Rmt 5210 250 5460 -- 5460

(d) Rmt 5785 325 6110 -- 6110

3.1.2

(a) Rmt 3990 160 4150 -- 4150

(b) Rmt 5180 200 5380 -- 5380

(c) Rmt 7760 250 8010 -- 8010

(d) Rmt 9375 325 9700 -- 9700

3.2

3.2.1

(a) Rmt 620 80 700 -- 700

(b) Rmt 1020 80 1100 -- 1100

(c) Rmt 1400 160 1560 -- 1560

(d) Rmt 2180 160 2340 -- 2340

(e) Rmt 3090 160 3250 -- 3250

(f) Rmt 6420 210 6630 -- 6630

(g) Rmt 8200 250 8450 -- 8450

3.2.2

(a) Rmt 1760 80 1840 -- 1840

(b) Rmt 2920 80 3000 -- 3000

(c) Rmt 4450 160 4610 -- 4610

(d) Rmt 6700 160 6860 -- 6860

(e) Rmt 9730 160 9890 -- 9890

(f) Rmt 12160 200 12360 -- 12360

(g) Rmt 15200 250 15450 -- 15450

3.3

PANEL MOUNTING BUSBARS

EARTH LEAKAGE CIRCUIT BREAKERSSuitable for 1200 A

Suitable for 100 A

Suitable for 200 A

Suitable for 300 A

Suitable for 400 A

Suitable for 630 A

Suitable for 800 A

Suitable for 300 A

Suitable for 400 A

Suitable for 630 A

Suitable for 800 A

Suitable for 1200 A

Supplying and erecting triple pole & neutral 440V / 500V panel mounting Copper Busbars with four equal Nos. of electrolyte bus having current density not more than 1.6 Amp. / sq.mm (Rated current / cross section area) duly wrapped with colour insulating tape for phase sequence of following current carrying capacity, erected with necessary bus bar supports /insulators, main cable socket to each bar, erected in existing cubical panel with necessary connections.

Suitable for 300 A

Suitable for 400 A

Supplying and erecting triple pole & neutral 440V/ 500V panel mounting Aluminium Busbars with four equal Nos. of bus having current density not more than 0.8 A/ sq. mm (Rated current/ cross section area) duly wrapped with colour insulating tape for phase sequence of following current carrying capacity, erected with necessary bus bar supports/ insulators, main cable socket to each busbar, erected in existing cubicle panel with necessary connections.

Suitable for 100 A

Suitable for 200 A

Suitable for 200 A

Suitable for 300 A

Suitable for 63/100 A

Suitable for 200 A

Suitable for 400 A

Supply & erection bus bar chamber confirming to IS-375 fabricated from 16 G.M.S. sheet, dust & vermin proof having hinged door with rubber gasket and necessary busbar supports with COPPER busbar having current density not more than 1.6 A/ sq. mm (Rated current/ cross section area) duly wrapped with colour insulation tape for phase sequence, three phase & neutral each suitable for following current capacity with necessary painting mounted on wall or pedestal frame of required size with necessary connections.

Supply & erection bus bar chamber conforming to IS-375 fabricated from 16 G.M.S.sheet, dust & vermin proof having hinged door with rubber gasket and necessary busbar supports with aluminium busbar having current density not more than 0.8 A/ sq. mm (Rated current/ cross section area) duly wrapped with colour insulation tape for phase sequence, three phase & neutral each suitable for following current capacity with necessary painting mounted on wall or pedestal frame of required size with necessary connections.

Suitable for 63/ 100 A

S.O.R. Mech 2019-20Page 55 of 166

Section- "D"


rates of GST




3.3.1

(a)Ea. 1730 50 1780 -- 1780

Ea. 1850 50 1900 -- 1900

Ea. 2250 50 2300 -- 2300

(b)Ea. 1870 50 1920 -- 1920

Ea. 1960 50 2010 -- 2010

Ea. 2560 50 2610 -- 2610

(c)Ea. 2120 50 2170 -- 2170

Ea. 2480 50 2530 -- 2530

Ea. 2550 50 2600 -- 2600

3.3.2

(a)Ea. 2040 70 2110 -- 2110

Ea. 2260 70 2330 -- 2330

Ea. 2930 70 3000 -- 3000

(b)Ea. 2180 70 2250 -- 2250

Ea. 2350 70 2420 -- 2420

Ea. 3010 70 3080 -- 3080

(c)Ea. 2390 70 2460 -- 2460

Ea. 2790 70 2860 -- 2860

Ea. 3480 70 3550 -- 3550

(d)Ea. 2860 70 2930 -- 2930

Ea. 4970 70 5040 -- 5040

3.3.3

(a) Ea. 2050 70 2120 -- 2120

(b) Ea. 2200 70 2270 -- 2270

(c) Ea. 2660 70 2730 -- 2730

(d) Ea. 2330 70 2400 -- 2400

(e) Ea. 2460 70 2530 -- 2530

(f) Ea. 3240 70 3310 -- 3310

3.3.4

(a) Ea. 270 50 320 -- 320

32A to 40 A, 4 Pole Three Phase Cat. II

63A, 4 pole Three Phase Cat. II

Supplying & fixing box for housing ELCB / ELCB + MCB combination made of 18 SWG sheet steel duly powder coated with gasket, dust & vermin proof bakelite shield two earthing terminals for following type of RCCB, ELCB, ELCB + MCBFor 2 pole

Cat. III

Supplying & erecting R&B approved make RCBO (Electro magnetic type only) working on residual current device having 6 KA short circuit breaking capacity and 30 mAmp. Sensitivity & 30 mili sec. tripping time conforming to IS 12640 test knob facility trip free mechanism operating for rated leakage at nominal ten volt, complete erected including all materials lugs screws etc. completed.

6A / 10A / 16A / 20A / 25A 2 pole single phase Cat. II

32A / 40A, 2 pole Single Phase Cat. II

63 A, 2 pole Single Phase Cat. II

6A to 25 A, 4 Pole Three Phase Cat. II

63 A FP

Cat. I

Cat. II

Cat. III

100 A FP (100 mA Sensitivity)

Cat. II

Cat. II

Cat. III

40 A FP

Cat. I

Cat. II

Cat. III

Cat. I

Cat. II

Cat. III

R&B Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on 3 phase and neutral 415V. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component for following Max. rating erected as directed.

25 A FP

Cat. I

Cat. III

40 A DP

Cat. I

Cat. II

Cat. III

63 A DP

Approved make ELCBs/ RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on single phase 240 V. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. for following Max.25 A DP

Cat. I

Cat. II

S.O.R. Mech 2019-20Page 56 of 166

Section- "D"


rates of GST




(b) Ea. 470 50 520 -- 520

3.4

3.4.1Ea. 65 15 80 -- 80

3.4.2Ea. 80 15 95 -- 95

3.4.3 Ea 20 10 30 -- 30

3.4.4Ea 30 10 40 -- 40

3.5

3.5.1Kg. 200 20 220 -- 220

3.5.2Kg. 70 20 90 -- 90

3.5.3Kg. 670 40 710 -- 710

3.5.4 Kg. 670 40 710 -- 710

3.5.5 Kg. 70 20 90 -- 90

3.5.6(a)Ea. 350 80 430 -- 430

3.5.6(b)

Ea. 810 150 960 -- 960

3.5.6(c)Ea. 180 20 200 -- 200

3.5.7Ea. 0 130 130 -- 130

3.5.8Ea. 0 325 325 -- 325

3.5.9

(a)Ea. 6630 520 7150 -- 7150

(b)Ea. 8370 600 8970 -- 8970

(c)

Ea. 12550 900 13450 -- 13450

3.5.10

DANGER NOTICE BOARDS

EARTHING

For Electrical Installation covering Transformer Neutrals, Lightning arrester Earthing, A.C.Plant & Sensitive Computer System(like Automation, SCADA) i.e independent Earthing in normal soil.Length of Pipe : 3.00 mtrs Back filling Compound :2 nos Bags of 25 Kg.Supplying & erecting in earthpit of minimum bore dia. 225mm size ASH or approved make Safe Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free G.I.Pipes having Outer pipe dia of 80 mm having 80-200 Micron galvanising, Inner pipe dia of 40 mm having 200-250 Micron galvanising, connection terminal dia of 14 mm with constant ohmic value surrounded by highly conductive compound with high charge dissipation suitable for following type of applications.

For using salt and charcoal / coke as required for pipe type earthing.

Add Extra for excavation in Semi hard rock (Murrum) by dry and wet blasting and chiselling for pipe type earthing Add Extra for excavation in Hard rock by dry and wet blasting and chiselling for pipe type earthing. Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded by highly conductive compound with high charge dissipation suitable for following type of applications.For Electrical Installation up to 440V in normal soilLength of pipe - 1 MtrBack filling compound - 1 Nos Bag of 15 Kg.

For Electrical installation up to 11 KV in normal soil.Length of Pipe : 2.00 mtrsBack filling Compound :1 no. Bag of 25 Kg.

Supply & erectionrequired size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel board, Motors etc. using proper clamp.Supply & erectionrequired size Copper strip for earthing of H.T. OCB / ACB/ Transformer, LT panel board, Motors etc. using copper clamp.

Supply & erectionAnnealed bare Copper wire 8 to 16 SWG.

Supply & erection HOT deep Galvanised iron strip wire 8 to 16 SWG.

Pipe type earthing having 150 cms.long and 2.5 cms. dia. galvanised iron pipe with coupling and buch buried in specially prepared earth pit complete with necessary 8 SWG earth wire.

Pipe type earthing with 40 mm dia 2.5 mtr long 'B' grade G.I. pipe with necessary coupling buch buried in specially prepared earth pit & G.I. earth wire of 8 SWG erected & connected as directed (For panel)

Supply & erectionmetallic vitrified danger notice board for High Voltage installation to be erected as per IS.Providing & erecting Medium Voltage Danger Notice Board sticker of standard sizeProviding & erecting High Voltage Danger Notice Board sticker of standard size

Supply & erectionrequired size Aluminium strip for earthing of H.T. OCB / ACB / Transformer, LT panel board, Motors etc. using copper clamp.

For 4 Pole

Supply & erectionmetallic vitrified danger notice board for Medium Voltage installation to be erected as per IS.

S.O.R. Mech 2019-20Page 57 of 166

Section- "D"


rates of GST




(a)Ea. 8580 520 9100 -- 9100

(b)

Ea. 10450 600 11050 -- 11050

(c)

Ea. 15600 900 16500 -- 16500

3.5.11 Ea. 1100 0 1100 -- 1100

3.5.12

Ea. 1900 800 2700 -- 2700

Ea. 2200 800 3000 -- 3000

Ea. 8400 800 9200 -- 9200

3.5.13Ea. 10 250 260 -- 260

3.5.14Ea. 0 380 380 -- 380

3.5.15

Ea. 600 200 800 -- 800

3.5.16

Ea. 800 200 1000 -- 1000

3.5.12

Ea. 5356 0 5356 -- 5356

3.5.13

Ea. 2266 0 2266 -- 2266

3.6 METALLIC ENCLOSURE

Maintenance free Chemical EarthingSupply of UL Listed Maintenance Free Earthing System made of copper bonded rod of 10 feet (3 mtr approx.)length, 17.2 mm dia. (Minimum copper bonding shall be 0.25mm, suitable for 25 kA fault current) along with Rod-to-Conductor connectors, 95% pure Carbon-BasedEarth enhancement material of 30kg, Pit Cover as required and as per specification.Supply of UL complying Maintenance Free Earthing System made of copper bonded rod of 4 feet (1.2 mtr approx.) length, 17.2 mm dia. (Minimum copper bonding shall be 0.25mm) along with Rod-to-Conductor connectors, 95% pure Carbon-Based Earth enhancement material of 5kg, Pit Cover as required and as perspecification.

For electrical installation up to 440 VLength of Pipe - 1 MtrBack filling compound - 1 Nos. of Bag of 15 Kgs.For Electrical installation up to 11 KV located in other than normal soil i.e. Soft Rock, Marshy Soil etc. -Length of Pipe : 2 mtr -Back filling Compound :1 no. Bag of 25 Kg. For Electrical Installation covering Transformer Neutrals, Lightning arrester Earthing, Instrumentation (like PLC Panel, SCADA)i.e. independent Earthing located in other than normal soil i.e.Soft Rock, Marshy Soil etc..-Length of Pipe : 3 Mtrs. -Back filling Compound :2 nos Bags of 25 Kg.Providing one bag of 25 Kg. Additional Back Filling Compound suitable for safe earthing device. Supplying & erecting funnel type earthing having earth plate of following size burred in specifically prepared earth pit 3 mtr. below ground with 40 kg. charcoal and salt with alternate layers of charcoal & salt, 20mm.dia. G.I. pipe with Funnel with a wire mesh for watering & bricks masonry block, C.I. Cover complete as per para 7.3 of IS 3043 with necessary length of double Galvanised Iron / copper earth wire No 6 SWG bolted with lug to the plate and covered in 12 mm dia. G.I. pipe 2.5 mtr long complete connected to the nearest switch gear with end socket as per direction & duly tested by earth tester confirming to IS (As per drawing) with following specification

Cast iron earth plate size 45 X 45 X 0.35 cms. buried in specially prepared 2.5 Mtr. Deep earth Pit complete with necessary G.I. strip in G.I. pipe 2 Mtr. long with coupling and G.I. plug for earthing of switch gear, conduit run or power plug etc.

Cast iron earth plate size 30 X 30 X 0.35 cms. buried in specially prepared 2.5 Mtr. deep earth pit complete with necessary G.I. strip in G.I. pipe 2 Mtr. long with coupling and G.I. plug for earthing of switch gear, conduit run or power plug etc.

ADD Extra for excavation in Hard rock by dry and wet blasting and chiselling for funnel type earthing of above .

ADD Extra for excavation in Semi hard rock (Murrum) by dry and wet blasting and chiselling for funnel type earthing of above

(C) with 60 x 60x 0.315 cms. Copper earth Plate

(B) With 45 x 45 x 0.35 cms. C.I. earth plate

(A) With 30 x 30 x 0.35 cms: C.I. earth plate

S.O.R. Mech 2019-20Page 58 of 166

Section- "D"


rates of GST




3.6.1

(A)

(a) Smt 16600 810 17410 -- 17410

(b) Smt 21840 810 22650 -- 22650

(c) Smt 33280 810 34090 -- 34090

(d) Smt 44270 810 45080 -- 45080

(B)

(a) Smt 11650 580 12230 -- 12230

(b) Smt 15280 580 15860 -- 15860

(c) Smt 23290 580 23870 -- 23870

(d) Smt 31300 580 31880 -- 31880

3.6.2

(A)

(a) Smt 3770 390 4160 -- 4160

(b) Smt 4550 390 4940 -- 4940

(B)

(a) Smt 2600 390 2990 -- 2990

(b) Smt 3120 390 3510 -- 3510

3.6.3

Smt 3650 250 3900 -- 3900

3.6.4(a)

Kg. 67 23 90 -- 90

3.6.4(b)

Kg. 170 40 210 -- 210

For 40 cms. Depth

without angle iron frame

For 25 cms. Depth

For 40 cms. depth

Meter cover made from multi chamber hollow PVC sections of 20 mm thick having all the corner joints with PVC solution angles without using any screws, nails shutters having required size of eye glass and with necessary locking arrangement hinged with box. The back of meter box should be fixed with timber. Hold fast for holding screws or nut bolts.Providing , erecting , fabricating the M.S. structure as per requirement on site incorporating proper size of M.S. angles, flats, bars, channels, sections complete with cutting, welding, grinding & finishing duly painted with one coat of red oxide with erection on site as per direction of engineer in charge with necessary grouting, cementing, plastering & finishing complete.Fabricating the box type items made from M.S. Sheet with A.I. supports, wings, doors, handles other hardware materials as per requirement design with finishing by three tank powder coating processed inside and outside painted, erected as directed including minor civil work.

(iv) with 1000 mm. depth

locally fabricated panel board

(i) with 350 mm depth

(ii) With 550 mm. Depth

(iii) with 750 mm. Depth

For 25 cms. Depth

(iv) with 1000 mm. depth

Steel cover as per drawing using 16 SWG M.S.sheet of following depth, to house the switch gear etc. complete with locking arrangement and lock with duplicate keys per cupboard and door handles erected with necessary support and painting. [One coat red oxide and two coat enamel paint]with angle iron frame

Providing & erecting weather proof, dust & vermin proof, floor mounted front operated indoor type cubical switchgear enclosure having IP-64 protection made from 14 SWG thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC M.S.sheet for internal partitions with necessary supporting angles, flats including cutting, bending, drilling, welding, riveting with internal partitions & cable alley as per requirements & instruction of engineer-in-charge with erection of supplied switch gears, BUSBARS, with suitable size of inter connecting PVC copper wire / copper-aluminium strips, rubber grommets, rib, bakelite control fuses for measuring instruments, earth bus & earth bolts, foundation flange - bolts-base Plates, sufficient nos. of hinged doors, handles with locking arrangement and rubber gasket complete. The Panel shall be painted with epoxy powder coating. (The rates excludes the cost of switchgears, bus bars, inter connecting mains & Copper Aluminium strips, meters, Fuses etc. The dimension shall be measured excluding base beams) The panel shall be supplied with following approved manufacturers with following size.

The standard companies switch gear shall be used and only manufacturers at CPRI approved factory and shall be certified by that company whose switch gears are used after fabrication for beneficial use

(i) with 350mm depth

(ii) with 550 mm. Depth

(iii)with 750 mm. Depth

S.O.R. Mech 2019-20Page 59 of 166

Section- "D"


rates of GST




3.6.5Kg. 7 23 30 -- 30

3.6.6Smt 120 50 170 -- 170

3.6.7

(a) Ea. 15 10 25 -- 25

(b) Ea. 2 0 2 -- 2

(c) Ea. 4 2 6 -- 6

3.6.8Smt 370 80 450 -- 450

4.1

4.1.1

(A)(a) Mtr. 10620 1265 11885 -- 11885

(b) Mtr. 14220 1265 15485 -- 15485

(c) Mtr. 17220 1265 18485 -- 18485

(B)(a) Mtr. 17315 1265 18580 -- 18580

(b) Mtr. 22900 1265 24165 -- 24165

(c) Mtr. 29800 1265 31065 -- 31065

4.2

4.2.1. 144 6 150 -- 150

4.2.2Ea. 250 5 255 -- 255

4.2.3Sq.M

tr990 0 990 -- 990

4.2.4 Sq.Mtr

2000 0 2000 -- 2000

4.2.5

Ea. 350 0 350 -- 350

4.2.6

Ea. 250 0 250 -- 250

4.2.7

Ea. 1050 50 1100 -- 1100

SUBSTATION EQUIPMENT & MAINTAINANCE

Supplying FIRE bucket round bottom of 9 litres capacity made out of 24 gauge G.I. sheet with extra handle at bottom duly painted white inside and Red out side with FIRE mark, filled with dry-sand and kept on existing stand provided or hung on wall hook.Supplying and erecting floor mounting stand for keeping four nos. of FIRE buckets comprising 1500 mm in length, 900 mm height frame made out of 30mm X 30 mm X 4 mm angle iron with cross supports for legs, welded with 4 hooks and duly painted with one coat of red lead and two coats of approved enamelled silver paint.

Providing printed instruction chart both in English and Gujarati and duly framed with front glasses for treatment of person suffering from Electric shock.Providing pair of rubber hand gloves suitable for working on 11kV/ 22kV supply.Supplying rubber matting of 6 mm thickness as per IS 5424 and of required length and breadth with good insulation property for 22 KVSupplying rubber matting of 12 mm thickness as per IS 5424 and of required length and breadth with good insulation property for 22 KVSupplying stand first AID box with antiseptic cream, medicine for use on wounds due burn, crepe bandage, gauge bandage, medicated ready to use bandage (Band-aid) adhesive tape for medicinal user, Scissors, anti-septic solution (savlon or similar) etc. (All above contents shall be of standard makes)

Copper Bus

SUBSTATION EQUIPMENT1600 A

Add. for additional character.

Add for additional each 25mm. height

Supplying and erecting nuwood 12mm thick on existing angle iron frame or wooden patti

Providing & erecting dust & vermin proof busduct fabricated from cold rolled 14 SWG CRCA sheet steel completed with required size of electrolytic grade copper / high grade aluminium. 63401 WP confirming to IS: 5082 for three phase & neutral of following capacities erected on SMC / DMC supporters designed & placed considering the most destructive fault conditions. The sheet metal work shall be dephosphated and given alkaline treatment and subject to seven tank process for cleaning oil, grease, dirt etc. Epoxy paint should be applied after application of two coats of primer. All BUSBARS should be insulated with close fitting sleeve of hard, smooth, dust & dirt free heat , shrunk PVC insulation of high dielectric strength. Busbar should be thoroughly cleaned at joint locations and a suitable contact grease and spring washers shall be used at joints. Aluminium Bus

Painting the number and words for inventory Identification on erected fittings / equipment’s or Such accessories as may required with good quality of enamelled paint as directed by engineer in charge.

up to 20 characters, up to 50 mm height.

1200 A

1600 A

800 A

1200 A

800 A

Add for specialised type of fabrication work on height by using scaffolding or tower stair or rope as well as for lift machine room & siren works.Painting by cleaning, the surface and applying one coat of primer and two coats of enamel paint for meter cup-board or base plate suitable to match the wall finish

S.O.R. Mech 2019-20Page 60 of 166

Section- "D"


rates of GST




4.2.8Ea. 47 23 70 -- 70

4.2.9

Ltr. 85 0 85 -- 85

4.2.10

(a) Ltr. 0 9 9 -- 9

(b) Ltr. 0 7 7 -- 7

4.3

4.3.1

Job 0 2500 2500 -- 2500

4.3.2

Job 0 1950 1950 -- 1950

4.3.3

Job 0 2500 2500 -- 2500

4.3.4Job 0 1950 1950 -- 1950

4.3.5Job 0 2200 2200 -- 2200

4.3.6

Job 0 4300 4300 -- 4300

4.3.7 Job 0 320 320 -- 320

4.3.8 Job 0 1950 1950 -- 1950

4.3.9

(a) Ea. 455 1495 1950 -- 1950

(b) Ea. 455 1495 1950 -- 1950

(c) Ea. 375 1725 2100 -- 2100

(d) Ea. 315 2185 2500 -- 2500

(e) Ea. 425 2875 3300 -- 3300

(f) Ea. 550 3450 4000 -- 4000

4.3.10

(a) Ea. 357 58 415 -- 415

(b) Ea. 357 58 415 -- 415

(c) Ea. 482 58 540 -- 540

(d) Ea. 722 58 780 -- 780

(e) Ea. 952 58 1010 -- 1010

(f) Ea. 2442 58 2500 -- 2500

4.3.11

(a) Ea. 185 35 220 -- 220

SUBSTATION MAINTENANCECarryout routine maintenance, servicing and testing of HT VCB (rating upto 1250 A) including cleaning of Breaker mechanism, auxiliary male-female contacts, time leg fuse contact coil contacts, overload and earth fault trip device control wiring contacts, lowering and lifting mechanism on trolley drawout mechanism etc. Carry out routine maintenance and servicing and testing of LT ACB (rating upto 2000 Amp) by cleaning fix contacts, moving contacts and arc chutes including servicing and putting the ACB in perfect working order after setting all relays and ON/ OFF mechanism.

1000 kVA

1600 kVA

Replacing old & unserviceable gasket bushing of HT for the following capacity Transformer250 kVA

1600 kVA

Replacing old and unserviceable gasket of Top cover plate of Transformer having following capacity.

250 kVA

315 kVA

500 kVA

750 kVA

Dismantling and refitting of transformer including cost of required new M.S. bolts of following capacity transformer 250 kVA

315 kVA

500 kVA

750 kVA

1000 kVA

Carry out routine maintenance and servicing of LT cubicle panel board having approximately 15 to 22 Nos. of switches cleaning and servicing the contacts tightning the connections of incoming and outgoing cables. and checking the operating mechanism for smooth functioning of switches. and putting them in smooth working order.

Carrying out the testing of earth fault and overload relay on LT side. Removing the fault of relay by checking the trip devices, control wiring and putting the same in working order. Testing and calibration of protective relays and metering devices through primary Injection up to 3000 AMP (3 coils sets)Routine maintenance of Transformer in operation covering check for Insulation Resistance, oil breakdown strength, reconditioning /replacement of silica gel, cleaning of transformer & topping up of oil if required. (excluding cost of transformer oil)Testing of transformer oil for dielectric breakdown strength.

Measurement of earthing resistance by loop test after isolating & cleaning joint.

Filtration of transformer oil as per I.S.S. for removal of moisture, carbon, slurry etc. by means of circulating oil through vacuum pump from heating elements and filters to with stand the breaking strength of the oil above 40kV beyond one minute tested in oil testing Kit. on site

at factory

Wall hook 22 to 25 cms. projection for keeping fire buckets made out of 15 mm dia. M.S rod grouted in wall to a depth of minimum 15 cms.

Transformer oil having good resistance to high electrical stress, high di-electric strength (50kV) low viscosity, low pour point, high flash point and excellent thermal properties for efficient heat transfer and cooling as per I.S.335 -1972.

S.O.R. Mech 2019-20Page 61 of 166

Section- "D"


rates of GST




(b) Ea. 205 35 240 -- 240

(c) Ea. 245 35 280 -- 280

(d) Ea. 265 35 300 -- 300

(e) Ea. 295 35 330 -- 330

(f) Ea. 315 35 350 -- 350

4.3.12

(a) Ea. 125 35 160 -- 160

(b) Ea. 125 35 160 -- 160

(c) Ea. 165 35 200 -- 200

(d) Ea. 190 35 225 -- 225

(e) Ea. 235 35 270 -- 270

(f) Ea. 245 35 280 -- 280

4.3.13(a) Ea. 0 1250 1250 -- 1250

(b) Ea. 0 1500 1500 -- 1500

(c) Ea. 0 1500 1500 -- 1500

(d) Ea. 0 2000 2000 -- 2000

(e) Ea. 0 2500 2500 -- 2500

(f) Ea. 0 2700 2700 -- 2700

4.3.14

(a) Ea. 58 12 70 -- 70

(b) Ea. 68 12 80 -- 80

(c) Ea. 108 12 120 -- 120

(d) Ea. 118 12 130 -- 130

(e) Ea. 128 12 140 -- 140

(f) Ea. 188 12 200 -- 200

4.3.15

(a) Kg. 422 58 480 -- 480

(b) Kg. 202 58 260 -- 260

4.3.16

(a) Kg. 382 58 440 -- 440

(b) Kg. 182 58 240 -- 240

4.3.17 Kg. 185 35 220 -- 220

4.3.18

(a) Kg. 42 58 100 -- 100

(b) Kg. 42 58 100 -- 100

(c) Kg. 72 58 130 -- 130

(d) Kg. 82 58 140 -- 140

(e) Kg. 92 58 150 -- 150

(f) Kg. 107 58 165 -- 165

4.3.19 Ea. 1527 173 1700 -- 1700

4.3.20(a) Ea. 1620 230 1850 -- 1850

(b) Ea. 1827 173 2000 -- 2000

4.3.21

(a) Ea. 241 29 270 -- 270

(b) Ea. 531 29 560 -- 560

Replacing the valve of the Transformer of rating capacity 250/ 315/ 500/ 750/ 1000 kVA of following size 3/4"

1"

Outside painting of Transformer for the following capacity

250/ 315/ 400/ 500 kVA

750/ 1000 kVA

Inside painting of 250/ 315/ 500/750/ 1000 kVA transformer

1000 kVA

1600 kVA

250 kVA

315 kVA

500 kVA

750 kVA

For Copper Coils

For Aluminium Coils

Insulating the HT/ LT copper Aluminium coils of transformer.

Reinsulating the HT/ LT Copper/ Alum. Coils of the following capacity transformer

Replacing the burnt unserviceable HT side winding coils for the transformer including rewinding, varnishing, vacuuming etc.For Copper Coils

For Aluminium coils

Replacing the burnt/ unserviceable LT side winding coils for transformer including rewinding, varnishing, vacuuming etc.

1000 kVA

1600 kVA

250 kVA

315 kVA

500 kVA

800 kVA

Removing washer ring for the coils of the following capacity Transformer

750 kVA

1000 kVA

1600 kVA

Removing the core plate of the following capacity Transformer.

250 kVA

315 kVA

500 kVA

1600 kVA

500 kVA

750 kVA

1000 kVA

750 kVA

1000 kVA

1600 kVA

Replacing old & unserviceable gasket bushing of LT for the following capacity Transformer250 kVA

315 kVA

315 kVA

500 kVA

S.O.R. Mech 2019-20Page 62 of 166

Section- "D"


rates of GST




(c) Ea. 386 29 415 -- 415

(d) Ea. 431 29 460 -- 460

4.3.22Ea. 67 23 90 -- 90

4.3.23(a) Ea. 1842 58 1900 -- 1900

(b) Ea. 2442 58 2500 -- 2500

4.3.24Ea. 1170 230 1400 -- 1400

4.3.25Ea. 3470 230 3700 -- 3700

4.3.26Ea. 202 23 225 -- 225

4.3.27Ea. 281 29 310 -- 310

4.3.28Ea. 151 29 180 -- 180

4.3.29Ea.

(a) Ea. 77 23 100 -- 100

(b) Ea. 107 23 130 -- 130

4.3.30395 35 430 -- 430

4.3.31Ea. 565 35 600 -- 600

4.3.32

(a) Ea. 0 2150 2150 -- 2150

(b) Ea. 0 2250 2250 -- 2250

(c) Ea. 0 2500 2500 -- 2500

(d) Ea. 0 2700 2700 -- 2700

4.3.33

(a) Ea. 0 1750 1750 -- 1750

(b) Ea. 0 3000 3000 -- 3000

4.3.34

(a) Ea. 0 2200 2200 -- 2200

(b) Ea. 0 2300 2300 -- 2300

4.3.35

(a) Ea. 0 450 450 -- 450

(b) Ea. 0 500 500 -- 500

(c) Ea. 0 250 250 -- 250

4.3.36(a) Ea. 0 3600 3600 -- 3600

(b) Ea. 0 5900 5900 -- 5900

4.3.37Sq.M

tr.3127 173 3300 -- 3300

4.3.38Sq.M

tr.4127 173 4300 -- 4300

4.3.39Sq.M

tr.5170 230 5400 -- 5400

Repairing of off load Tap changing of 250/ 315/ 500/ 750/ 1000kVA Transformer.

Replacing the breather of the Transformer of following capacity.

250/ 315kVA

500/ 750/ 1000kVA

Supplying & fixing Steel Chequered Plate having 7 mm thickness, duly painted with two coats of black Japan colour. (Average Wt. 61.1 kg/ Sq.Mtr.)Supplying & fixing Steel Chequered Plate having 10 mm thickness, duly painted with two coats of black Japan colour. (Average Wt. 84.6 kg/ Sq.Mtr.)

Supplying & fixing Steel Chequered Plate having 12 mm thickness, duly painted with two coats of black Japan colour. (Average Wt. 200.3 kg/ Sq.Mtr.)

Add for each block of additional 30km

Loading/ Unloading transformer on one side 250/ 315/ 500kVA

750/ 1000kVA

Conveyance charges for transformer from workshop to site or back one side) Local up to 10km

Outside Divisional Head Quarter for first 30km from store

Assembling the repaired / replaced copper/ Aluminium coils of the following capacity transformer 250/ 315/ 500kVA

750/ 1000 kVA

Carrying out routine tests as per relevant IS/ IEC standards for following capacity transformer.250/ 315kVA

500/ 750/ 1000 kVA

500kVA

750kVA

1000kVA

Drying the repaired transformer with appropriate heat air of following capacity transformer. 250kVA/ 315kVA

Replacing L.T. Bushing metal parts of 250/315/ 315/ 500/ 750/ 1000kVA Transformer by new one.Replacing L.T. Bushing all/ other parts of the 250/ 315/ 500/750/ 1000kVA Transformer.

250/ 315 kVA

500 / 750 / 1000 kVA

Replacing H.T Bushing metal parts of 250/ 315/ 500/ 750/ 1000kVA Transformer by new one.

Replacing L.T. bushing of following capacity Transformer

Replacing H.T. bushing of 250/ 315/ 500/750/ 1000kVA Transformer by new one

Replacement of On load Tap changing of 250/ 315/500/750/ 1000kVA Transformer.

Replacing H.T Bushing all other parts of 250/ 315/ 500/ 750/ 1000kVA Transformer

1.1/2"

Replacing the oil level glass of the 250/ 315/ 500/ 750/ 1000kVA by new one

1.1/4"

S.O.R. Mech 2019-20Page 63 of 166

Section - "D"


rates of GST


5-1-1.

Job 0.00 165.00 165.00 5.0% 173.25Job 0.00 220.00 220.00 5.0% 231.00Job 0.00 330.00 330.00 5.0% 346.50

5-1-2.

Ea. 55.00 33.00 88.00 12.0% 98.56Ea. 88.00 33.00 121.00 12.0% 135.52Ea. 121.00 33.00 154.00 12.0% 172.48

5-1-3. Ea. 495.00 55.00 550.00 12.0% 616.00

5-1-4. Ea. 605.00 110.00 715.00 12.0% 800.80

5-1-5. Ea. 990.00 132.00 1122.00 12.0% 1256.64

5-1-6. Ea. 1650.00 165.00 1815.00 12.0% 2032.80

5-1-7. Ea. 2145.00 220.00 2365.00 12.0% 2648.80

5-1-8. Ea. 2750.00 330.00 3080.00 12.0% 3449.60

5-1-9. Ea. 3850.00 330.00 4180.00 12.0% 4681.60

5-1-10. Ea. 4950.00 385.00 5335.00 12.0% 5975.20

5-1-11. Ea. 5500.00 550.00 6050.00 12.0% 6776.00

5-1-12. Ea.

Ea. 154.00 44.00 198.00 12.0% 221.76Ea. 220.00 44.00 264.00 12.0% 295.68Ea. 275.00 44.00 319.00 12.0% 357.28Ea. 308.00 66.00 374.00 12.0% 418.88Ea. 385.00 66.00 451.00 12.0% 505.12Ea. 550.00 66.00 616.00 12.0% 689.92Ea. 638.00 110.00 748.00 12.0% 837.76Ea. 660.00 110.00 770.00 12.0% 862.40

5-2-1.

Job 0.00 220.00 220.00 5.0% 231.00Job 0.00 275.00 275.00 5.0% 288.75Job 0.00 385.00 385.00 5.0% 404.25Job 0.00 550.00 550.00 5.0% 577.50

5-2-2.

Ea. 0.00 350.00 350.00 5.0% 367.50Ea. 0.00 385.00 385.00 5.0% 404.25Ea. 0.00 495.00 495.00 5.0% 519.75

Opening the open well sub. mono pump set for fault finding , carry out required repairs refitting the same with necessary oiling, greasing & overhauling & making pump set in good working condition. (Excludes cost of repairing. Includes to & from transportation)(i) 1.0 HP to 5HP (ii) 7.5 to 15HP (iii) Above 15HP

(H) For 20 H.P. motor/pump

Dewatering sump well by hiring pump sets & temporary pipe connections of following sump capacity (a) up to 5000 Ltr (b) Above 5000 Ltr to 20000 Ltr (c) Above 20000 Ltr to 1 Lac Ltr (d) Above 1 Lac Ltr

SECTION 6--2 REPAIRING OF OPEN WELL HORIZONTAL MONO PUMP SETS

(c)10 Hp to 20 HPRewinding of 1 HP 230V single phase motor as per original winding design by using super enamelled copper Wire and putting the same in working condition as per original.Rewinding of 2 HP 3 phase 440V motor as per original winding design by using super enamelled copper Wire and putting the same in working condition as per original.Rewinding of 3 H.P., 3 phase 440V motor as per original winding design by using super enamelled copper Wire and putting the same in working condition as per original.

Rewinding of 5 H.P., 3 phase 440V motor as per original winding design by using super enamelled copper Wire and putting the same in working condition as per original.

Rewinding of 7.5 H.P., 3 phase 440V motor as per original winding design by using super enamelled copper Wire and putting the same in working condition as per original.

(c)10 Hp to 20 HP

REPAIRING OF MACHINERIESSECTION 6--1 REPAIRING OF MONO BLOCK PUMP MOTORS

Removing deteriorated gasket, gland packing, washer nuts & bolts before refitting of motor pump set.(a) Up to 3 HP(b) Above 3 HP to 7.5 HP



Replacing burnout unserviceable ball bearing / Roller bearing suitable for following motors for mono block pump sets

(A) For 1 H.P. motor/pump



Removing the pump set from foundation after removing suction & discharge connection pipes & all wiring connections taking it to workshop & open it for fault finding , refitting the same, after carrying out repairing, taking back on site refitting on foundation with pipe & wiring connections & put in working condition. (Excludes cost of repairing. Includes to & from transportation)

(F) For 10/12.5 H.P. motor/pump (G) For 15 H.P. motor/pump

(B) For 2 H.P. motor/pump (C) For 3 H.P. motor/pump

(a) Up to 3 HP(b) Above 3 HP to 7.5 HP

(D) For 5 H.P. motor/pump (E) For 7.5 H.P. motor/pump


Rewinding of 12.5 H.P., 3 phase 440V motor as per original winding design by using super enamelled copper Wire and putting the same in working condition as per original.

S.O.R. Mech - 2019-20Page 64 of 166

Section - "D"

5-2-3.

Ea. 1012.00 110.00 1122.00 12.0% 1256.64Ea. 1375.00 110.00 1485.00 12.0% 1663.20

5-2-4.

Ea. 1210.00 110.00 1320.00 12.0% 1478.40Ea. 1485.00 110.00 1595.00 12.0% 1786.40Ea. 1870.00 220.00 2090.00 12.0% 2340.80Ea. 2255.00 220.00 2475.00 12.0% 2772.00Ea. 3135.00 275.00 3410.00 12.0% 3819.20Ea. 3245.00 275.00 3520.00 12.0% 3942.40Ea. 3465.00 275.00 3740.00 12.0% 4188.80Ea. 3685.00 330.00 4015.00 12.0% 4496.80Ea. 4455.00 385.00 4840.00 12.0% 5420.80Ea. 5200.00 415.00 5615.00 12.0% 6288.80

5-2-5.

Ea. 319.00 55.00 374.00 12.0% 418.88Ea. 578.00 55.00 633.00 12.0% 708.96Ea. 957.00 55.00 1012.00 12.0% 1133.44

5-2-6.

Ea. 506.00 55.00 561.00 12.0% 628.32Ea. 770.00 55.00 825.00 12.0% 924.00Ea. 935.00 55.00 990.00 12.0% 1108.80

5-2-7.

Ea. 220.00 55.00 275.00 12.0% 308.00Ea. 330.00 55.00 385.00 12.0% 431.20Ea. 385.00 55.00 440.00 12.0% 492.80

5-2-8.

Ea. 220.00 55.00 275.00 12.0% 308.00Ea. 330.00 55.00 385.00 12.0% 431.20Ea. 385.00 55.00 440.00 12.0% 492.80

5-2-9.

Ea. 1210.00 55.00 1265.00 12.0% 1416.80Ea. 1573.00 55.00 1628.00 12.0% 1823.36Ea. 2057.00 55.00 2112.00 12.0% 2365.44

5-2-10.

Ea. 275.00 110.00 385.00 12.0% 431.20Ea. 495.00 165.00 660.00 12.0% 739.20Ea. 825.00 165.00 990.00 12.0% 1108.80

5-2-11.

Ea. 825.00 110.00 935.00 12.0% 1047.20Ea. 990.00 165.00 1155.00 12.0% 1293.60Ea. 1210.00 165.00 1375.00 12.0% 1540.00

5-3-1.

Ea. 0.00 275.00 275.00 5.0% 288.75Ea. 0.00 385.00 385.00 5.0% 404.25Ea. 0.00 495.00 495.00 5.0% 519.75Ea. 0.00 660.00 660.00 5.0% 693.00

5-3-2.

Ea. 1815.00 165.00 1980.00 12.0% 2217.60Ea. 2277.00 165.00 2442.00 12.0% 2735.04Ea. 3091.00 275.00 3366.00 12.0% 3769.92Ea. 3542.00 330.00 3872.00 12.0% 4336.64Ea. 4433.00 385.00 4818.00 12.0% 5396.16Ea. 5698.00 495.00 6193.00 12.0% 6936.16Ea. 8349.00 1144.00 9493.00 12.0% 10632.16Ea. 10758.00 2002.00 12760.00 12.0% 14291.20Ea. 22770.00 2530.00 25300.00 12.0% 28336.00

5-3-3.

Ea. 1430.00 110.00 1540.00 12.0% 1724.80Ea. 2068.00 110.00 2178.00 12.0% 2439.36

(H) 46 to 54 H.P (I) 55 to 75 H.PReplacement of bronze/ carbon thrust bearing with fibre plate & housing for

(i)150 mm. dia. (ii)200 mm. dia

(B) 7.5 H.P (C) 10 to 15 H.P (D) 16 to 20 H.P (E) 21 to 25 H.P (F) 26 to to 35 H.P (G) 36 to 45 H.P

(i) 1HP to 5HP (ii) 7.5 to 15HP (iii) 20HP to 35 HP (iv) Above 35 HPRewinding of submersible motor by using approved make PVC insulated copper winding Cores of suitable size complete with connection. Capacity Suitable for pump of following size. Dismantled Materials to be retained by agency.

(A) 5 HP

(iii) above 15 HPReplacement of Bronze / Gunmetal impeller for open well horizontal submersible pump set(i) 1HP to 5 HP (ii) 7.5Hp to 15 HP (iii) above 15 HP

Opening the submersible pump set for fault finding , carry out required repairs refitting the same with necessary oiling, greasing & overhauling & making pump set in good working condition. (Excludes cost of repairing. Includes to & from transportation)

SECTION 6--3 REPAIRING OF SUBMERSIBLE PUMP SETS

(i) 1HP to 5 HP (ii) 7.5Hp to 15 HP (iii) above 15 HPReplacement of cast iron impeller for openwell horizontal submersible pump pump sets(i) 1HP to 5 HP (ii) 7.5Hp to 15 HP

(iii) above 15 HPReplacing gasket, oil, nuts, bolts & washers for open well horizontal submersible pump sets.(i) 1HP to 5 HP (ii) 7.5Hp to 15 HP (iii) above 15 HPReplacement of Bronze / Carbon thrust bearing with fibber plate & bushing suitable for open well horizontal submersible pump set for

(i) 1HP to 5 HP (ii) 7.5Hp to 15 HP (iii) above 15 HPReplacement of Gun metal /Bronze bushing for open well horizontal submersible pump set(i) 1HP to 5 HP (ii) 7.5Hp to 15 HP

(j) 30 HP - 440VReplacement of S.S. sleeves for shaft of open well horizontal submersible pump sets for (i) 1HP to 5HP (ii) 7.5 to 15HP (iii) Above 15HPReplacement of Stainless Steel bushing fitted in end shield for open well horizontal submersible pump set

(d) 7.5 HP - 440V (e) 10 HP - 440V (f) 12.5 HP - 440V (g) 15 HP - 440V (h) 20 HP - 440V (i) 25 HP - 440V

(b) 1HP - 230 VRewinding 3 phase, 440V motor for open well horizontal mono pump set by using poly. cap copper winding wire & putting the same in working order for pump capacity of (a) 0.5 H.P./ 1 HP / 1.5 HP - 440V (b) 2 HP / 3 HP - 440V(c)5 HP - 440V

Rewinding single phase 230V motor for open well horizontal mono pump set by using polycab copper winding wire & putting the same in working order for pump capacity of (a) 0.5 HP - 230V

S.O.R. Mech - 2019-20Page 65 of 166

Section - "D"

5-3-4.

Ea. 495.00 55.00 550.00 12.0% 616.00Ea. 990.00 55.00 1045.00 12.0% 1170.40

Ea. 297.00 22.00 319.00 12.0% 357.28Ea. 495.00 22.00 517.00 12.0% 579.04

5-3-5.

Ea. 330.00 55.00 385.00 12.0% 431.20Ea. 495.00 55.00 550.00 12.0% 616.00

Ea. 550.00 55.00 605.00 12.0% 677.60Ea. 693.00 55.00 748.00 12.0% 837.76

5-3-6.Ea. 396.00 55.00 451.00 12.0% 505.12Ea. 605.00 55.00 660.00 12.0% 739.20

5-3-7.Ea. 55.00 11.00 66.00 12.0% 73.92Ea. 138.00 11.00 149.00 12.0% 166.88

5-3-8.

Ea. 308.00 55.00 363.00 12.0% 406.56Ea. 605.00 55.00 660.00 12.0% 739.20

Ea. 693.00 55.00 748.00 12.0% 837.76Ea. 1100.00 55.00 1155.00 12.0% 1293.60

5-3-9.

Ea. 286.00 28.00 314.00 12.0% 351.68Ea. 473.00 44.00 517.00 12.0% 579.04

Ea. 83.00 11.00 94.00 12.0% 105.28Ea. 121.00 11.00 132.00 12.0% 147.84

5-3-10.Ea. 94.00 17.00 111.00 12.0% 124.32Ea. 187.00 22.00 209.00 12.0% 234.08

(B) Add per stage (i)150 mm. dia. (ii)200 mm. dia Replacement of suction strainer (i)150 mm. dia. (ii)200 mm dia.

(i)150 mm. dia. (ii)200 mm. dia Replacement of S.S.Shaft for (A) 3 stage pump (i)150 mm. dia. (ii)200 mm. dia

(ii)200 mm. dia Replacement of Bowl bearing/ bush(A) Rubber (i)150 mm. dia. (ii)200 mm. dia (B) Lead

(ii)200 mm. dia Replacement of Bronze impeller with neck ring. (i)150 mm. dia. (ii)200 mm. dia Replacement of Shaft sleeve stainless steel.(i)150 mm. dia.

Replacement of stage casing bowl with nuts and bolts.(A)C.I. (i)150 mm. dia. (ii)200 mm. dia (B)Bronze (i)150 mm. dia.

(A) Bronze (i)150 mm. dia. (ii)200 mm. dia (B)Rubber (i)150 mm. dia. (ii)200 mm. dia

Replacement of motor bush, upper/ lower with sleeve with following material

S.O.R. Mech - 2019-20Page 66 of 166

Section- "E"

Rates exclusive of

GST

Prevailing rates of GST

Rates inclusive of

GST1

I

II Cat No. Discharge in LPM

Head in mtr Mini Motor HP

a) 1.0 90 60.0 3.00 No 10,970 12% 12,286

b) 1.1 90 90.0 5.00 No 12,900 12% 14,448

c) 1.2 90 120.0 6.00 No 14,500 12% 16,240

d) 1.3 90 150.0 7.50 No 17,000 12% 19,040

e) 1.4 90 180.0 10.00 No 19,800 12% 22,176

f) 2.0 135 60.0 4.00 No 11,100 12% 12,432

g) 2.1 135 90.0 6.00 No 13,100 12% 14,672

h) 2.2 135 120.0 7.50 No 15,120 12% 16,934

i) 2.3 135 150.0 10.00 No 18,000 12% 20,160

j) 2.4 135 180.0 12.50 No 20,340 12% 22,781

k) 2.5 135 210.0 15.00 No 25,530 12% 28,594

l) 2.6 135 240.0 17.50 No 26,100 12% 29,232

m) 2.7 135 255.0 17.50 No 26,430 12% 29,602

n) 3.0 180 72.0 6.00 No 12,510 12% 14,011

o) 3.1 180 108.0 10.00 No 16,110 12% 18,043

p) 3.2 180 144.0 12.50 No 19,370 12% 21,694

q) 3.3 180 163.0 12.50 No 20,110 12% 22,523

r) 3.4 180 180.0 12.50 No 22,190 12% 24,853

s) 3.5 180 215.0 15.00 No 25,551 12% 28,617

t) 3.6 180 255.0 20.00 No 29,820 12% 33,398

u) 3.7 180 275.0 22.50 No 31,000 12% 34,720

v) 4.0 240 72.0 7.50 No 13,025 12% 14,588

w) 4.1 240 108.0 25.00 No 16,700 12% 18,704

x) 4.2 240 144.0 15.00 No 21,480 12% 24,058

y) 4.3 240 170.0 17.50 No 24,120 12% 27,014

z) 4.4 240 190.0 20.00 No 25,600 12% 28,672

aa) 4.5 240 210.0 20.00 No 31,150 12% 34,888

ab) 4.6 240 230.0 25.00 No 28,000 12% 31,360

ac) 4.7 240 250.0 25.00 No 30,750 12% 34,440

ad) 5.0 320 55.0 7.50 No 14,211 12% 15,916

ae) 5.1 320 92.0 12.50 No 16,600 12% 18,592

af) 5.2 320 130.0 17.50 No 21,750 12% 24,360

ag) 5.3 320 150.0 20.00 No 24,100 12% 26,992

ah) 6.0 400 60.0 10.00 No 16,430 12% 18,402

ai) 6.1 400 90.0 15.00 No 21,130 12% 23,666

aj) 6.2 400 120.0 20.00 No 26,700 12% 29,904

ak) 6.3 400 150.0 22.50 No 31,000 12% 34,720

al) 7.0 510 52.0 12.50 No 20,110 12% 22,523

am) 7.1 510 87.0 20.00 No 27,810 12% 31,147

an) 7.2 510 123.0 25.00 No 32,100 12% 35,952

ao) 7.3 510 141.0 30.00 No 34,600 12% 38,752

ap) 7.4 510 159.0 35.00 No 35,600 12% 39,872

aq) 7.5 510 175.0 40.00 No 38,310 12% 42,907

ar) 8.0 800 72.0 25.00 No 28,900 12% 32,368

as) 8.1 800 108.0 35.00 No 33,760 12% 37,811

at) 8.2 800 144.0 45.00 No 40,500 12% 45,360

au) 8.3 800 162.0 50.00 No 41,850 12% 46,872

av) 8.4 800 180.0 55.00 No 46,160 12% 51,699

aw) 8.5 800 198.0 60.00 No 48,430 12% 54,242

ax) 9.0 1,200 63.0 27.50 No 30,810 12% 34,507

Unit

Approved Rate for 2019-20Sr. No. Description of Item

3 Phase Borewell Submersible Pump Sets

Electric motor driven Borewell submersible pump set conforming to I.S. 8034 and motor conforms to IS-9283 working at 3 phase 400/440 volt 50 C/S A.C. supply & 2900 R.P.M.

S.O.R. Mech 2019-20Page 67 of 166

Section- "E"

Rates exclusive of

GST


Rates inclusive of

GST

Unit


ay) 9.1 1,200 105.0 45.00 No 40,900 12% 45,808

az) 9.2 1,200 126.0 55.00 No 45,750 12% 51,240

ba) 9.3 1,200 147.0 65.00 No 50,310 12% 56,347

bb) 9.4 1,200 167.0 75.00 No 57,810 12% 64,747

bc) 9.5 1,200 187.0 80.00 No 66,482 12% 74,459

bd) 10.0 600 50.0 12.50 No 21,240 12% 23,789

be) 10.1 600 83.0 17.50 No 28,400 12% 31,808

bf) 10.2 600 116.0 25.00 No 30,350 12% 33,992

bg) 10.3 600 132.0 30.00 No 35,550 12% 39,816

bh) 10.4 600 149.0 35.00 No 38,770 12% 43,422

bi) 10.5 600 165.0 40.00 No 39,600 12% 44,352

bj) 10.6 600 180.0 45.00 No 40,840 12% 45,741

bk) SP1 1,700 52.0 30.00 No 52,863 12% 59,207

bl) SP2 1,700 86.0 55.00 No 70,214 12% 78,640

bm) SP3 2,000 50.0 35.00 No 60,288 12% 67,523

bn) SP4 2,000 74.0 50.00 No 77,296 12% 86,572

bo) SP5 2,900 45.0 45.00 No 74,500 12% 83,440

bp) SP6 2,900 68.0 65.00 No 97,100 12% 108,752

bq) LD2.0 420 72.0 12.50 No 21,800 12% 24,416

br) LD2.1 420 108.0 20.00 No 29,520 12% 33,062

bs) LD2.2 420 144.0 27.50 No 32,240 12% 36,109

bt) LD2.3 420 180.0 35.00 No 36,000 12% 40,320

bu) LD2.4 420 216.0 40.00 No 37,440 12% 41,933

bv) LD2.5 420 252.0 40.00 No 102,090 12% 114,341

bw) HD-1 5,000 40.0 75.00 No 90,102 12% 100,914

bx) HD-2 5,000 60.0 110.00 No 131,694 12% 147,497

by) HD-3 7,500 40.0 110.00 No 133,106 12% 149,079

bz) HD-4 7,500 60.0 160.00 No 199,659 12% 223,618

22.1

a) No. 5,770 18% 6,809

b) No. 5,770 18% 6,809

c) No. 6,986 18% 8,243

d) No. 7,607 18% 8,976

e) No. 9,266 18% 10,934

f) No. 11,476 18% 13,542

2.2

a) No 20,230 18% 23,871

b) No 22,844 18% 26,956

c) No 27,836 18% 32,846

d) No 31,503 18% 37,174

e) No 38,532 18% 45,468

f) No 42,716 18% 50,405

g) No 54,800 18% 64,664

h) No 65,260 18% 77,007 A. T. S. from 81 to 90 HP

A. T. S. from 31 to 35 HP






D. O. L. up to 7.5 HP

S. D. from 8 to 10 HP



Auto Transformer Starter suitable for local & remote pump control application consisting of Auto Transformer (vacuum impregnated, air cooled having three (3) tappings at 50%, 65% and 80%), incomer MCCB / MPCB, overload relay and contactors as per Type II coordination including digital MFM with RS 485 communication port, analogue type ammeter with selector switch, run hour meter, required protective relays & control accessories.A. T. S. from 21 to 30 HP

Control Panel BoardDOL / Star Delta starter suitable for local & remote pump control application consisting of MPCB, overload relay and contactors as per Type II coordination including digital voltmeter, analogue ammeter with selector switch, run hour meter, required protective relays & control accessories.

D. O. L. up to 3 HP

D. O. L. up to 5 HP

S.O.R. Mech 2019-20Page 68 of 166

Section- "E"

Rates exclusive of

GST


Rates inclusive of

GST

Unit


2.3

a) No 185,894 18% 219,355

b) No 210,431 18% 248,309

c) No 210,431 18% 248,309

d) No 210,431 18% 248,309

e) No 226,613 18% 267,403

f) No 226,613 18% 267,403

3

3.1

a) RMT 25.23 18% 29.77

b) RMT 38.73 18% 45.70

c) RMT 57.67 18% 68.05

d) RMT 80.14 18% 94.57

e) RMT 129.07 18% 152.30

f) RMT 206.51 18% 243.68

g) RMT 306.24 18% 361.36

h) RMT 434.80 18% 513.06

3.2

a) RMT 34.00 18% 40.12

b) RMT 65.00 18% 76.70

c) RMT 98.00 18% 115.64

d) RMT 143.00 18% 168.74

e) RMT 231.00 18% 272.58

f) RMT 365.00 18% 430.70

g) RMT 570.00 18% 672.60

h) RMT 785.00 18% 926.30

4A

Sr. No RatingH.P

Discharge LPM

a) 5 285 No. 13,600 12% 15,232

b) 7.5 545 No. 20,000 12% 22,400

c) 7.5 550 No. 20,000 12% 22,400

d) 12.5 980 No. 30,600 12% 34,272

e) 17.5 1750 No. 39,500 12% 44,240

f) 15 1140 No. 32,700 12% 36,624

g) 20 1900 No. 39,500 12% 44,240

4B

Sr. No Rating H.P

Discharge LPM

31

39

33

Monoblock pump 3 phase 400/440 vott, 50 c/s. A.C. Supply & 2800 RPM following IS 9079MOC : Casing: CI-FG260, Impeller : SS-CF8M & Shaft : SS:410

Head mtr.

30

1 R x 3 C x 25.0 mm2

1 R x 3 C x 35.0 mm2

Monobloc pump 3 phase 400/440 vott, 50 c/s. A.C. Supply & 2800 RPM following IS 9079 at departmental stores with following MOC : Casing: CI-FG260, Impeller : Bronze & Shaft : SS:410

Head mtr.24

24

33

1 R x 3 C x 1.5 mm2

1 R x 3 C x 2.5 mm2

1 R x 3 C x 4.0 mm2

1 R x 3 C x 6.0 mm2

1 R x 3 C x 10.0 mm2

1 R x 3 C x 16.0 mm2

1 R x 3 C x 6.0 mm2

1 R x 3 C x 10.0 mm2

1 R x 3 C x 16.0 mm2

1 R x 3 C x 25.0 mm2

1 R x 3 C x 35.0 mm2

PVC insulated round submersible cable as per detailed technical specifications of R/C of GWSSB conforming to IS 694, IEC 60227 / 60228.

Note: Above rates of Flat PVC copper cables are based on IEEMA circular no. IEEMA (PVC) Cable/02 of 2018 issued on Dtd. 09.03.2018 (Month of February 2018). Notional base price of electrolytic copper wire Rod is Rs. 4,81,473/MT and Notional base price of PVC compund is Rs. 1,33,000/M.T. of grade CW-22.

PVC insulated flat / round submersible copper cables

PVC insulated flat submersible cable as per detailed technical specifications of R/C of GWSSB conforming to IS 694, IEC 60227 / 60228.

1 R x 3 C x 1.5 mm2

1 R x 3 C x 2.5 mm2

1 R x 3 C x 4.0 mm2

Microprocessor based soft starter, fully automatic 415V suitable for local & remote pump control application consisting of incomer MCCB of suitable rating, semi conductor fuses, microprocessor based soft starter with built in by pass arrangement (conforming to IS/ IEC 60947-4-1-2-3) with RS 485 communication port, external display unit with keypad including temperature scanner with minimum 10 channels - suitable for accepting RTD (Pt 100) / thermister inputs, digital MFM with RS 485 communication port, analogue type ammeter with selector switch, run hour meter, required protective relays & control accessories.

MP based soft starter- 100 HP

MP based soft starter from 101 to 120 HP





S.O.R. Mech 2019-20Page 69 of 166

Section- "E"

Rates exclusive of

GST


Rates inclusive of

GST

Unit


a) 5 285 No. 12,600 12% 14,112

b) 7.5 545 No. 18,100 12% 20,272

c) 7.5 550 No. 18,100 12% 20,272

d) 12.5 980 No. 28,900 12% 32,368

e) 17.5 1750 No. 38,200 12% 42,784

f) 15 1140 No. 31,000 12% 34,720

g) 20 1900 No. 38,200 12% 42,784

5

Sr. No Category Rating H.P. Discharge LPM

Headmtr.

a) SM - 2.1 4 220 22.5 No 9,930 12% 11,122

b) SM - 2.2 5.5 360 24 No 10,800 12% 12,096

c) SM - 2.3 6.5 438 22.5 No 10,525 12% 11,788

d) SM - 2.4 10 530 27 No 12,160 12% 13,619

e) SM - 2.5 10 498 32.5 No 12,900 12% 14,448

f) SM - 2.6 12.5 600 40 No 15,711 12% 17,596

g) SM - 2.7 15 690 40 No 17,230 12% 19,298

h) SM - 2.8 15 600 46 No 17,960 12% 20,115

i) SM - 2.9 15 440 52 No 17,500 12% 19,600

j) SM - 2.10 25 700 70 No 28,500 12% 31,920

k) SM - 2.5.1 5.5 510 16 No 10,870 12% 12,174

l) SM - 2.5.2 6.5 440 26 No 11,210 12% 12,555

m) SM - 2.5.3 10 720 25 No 13,050 12% 14,616

n) SM - 2.5.4 15 900 37 No 24,050 12% 26,936

o) SM - 2.5.5 15 750 42 No 24,300 12% 27,216

p) SM - 2.5.6 25 1000 58 No 32,200 12% 36,064

q) SM - 3.1 10 700 24 No 13,670 12% 15,310

r) SM - 3.2 12.5 1000 24 No 16,470 12% 18,446

s) SM - 3.3 10 700 27 No 14,270 12% 15,982

t) SM - 3.4 15 870 32.5 No 17,140 12% 19,197

u) SM - 3.5 17.5 1300 32 No 25,100 12% 28,112

v) SM - 3.6 20 1175 37 No 25,300 12% 28,336

w) SM - 3.7 25 1300 50 No 34,581 12% 38,731

x) SM - 4.1 7.5 1275 11 No 13,240 12% 14,829

y) SM - 4.2 10 1450 12.5 No 15,030 12% 16,834

z) SM - 4.3 12.5 1160 20 No 15,400 12% 17,248

aa) SM - 4.4 15 1250 25 No 18,550 12% 20,776

ab) SM - 4.5 17.5 1600 26 No 24,980 12% 27,978

ac) SM - 4.6 20 1500 30 No 25,240 12% 28,269

ad) SM - 4.7 25 1860 34 No 32,700 12% 36,624

6

Category Discharge Head H.P.

a) Q-1.1 20 60 1 No 7,131 12% 7,987

b) Q-1.2 20 90 1.5 No 7,790 12% 8,725

31

39

33

Monoset sub. pump 3 phase 400/440 vott, 50 c/s. A.C. Supply & 2900 RPM , following IS 14220MOC : Casing: CI-FG260, Impeller : Bronze & Shaft : SS:410

Single phase Borewell sub pump motor set MOC: Casing: CI-FG260, Impeller : Bronze & Shaft : SS:410

30

24

24

33

S.O.R. Mech 2019-20Page 70 of 166

Section- "E"

Rates exclusive of

GST


Rates inclusive of

GST

Unit


c) Q-1.3 20 110 1.5 No 8,719 12% 9,765

d) Q-1.4 20 150 2 No 8,662 12% 9,701

e) Q-1.5 20 180 3 No 11,610 12% 13,003

f) Q-2.1 40 60 1.5 No 7,638 12% 8,555

g) Q-2.2 40 90 3 No 9,293 12% 10,408

h) Q-2.3 40 110 3 No 10,350 12% 11,592

i) Q-2.4 40 150 3 No 13,365 12% 14,969

j) Q-2.5 40 180 4 No 15,444 12% 17,297

k) Q-3.1 60 60 2 No 8,538 12% 9,563

l) Q-3.2 60 90 3 No 10,448 12% 11,702

7(A)

a) Job 20,381 5% 21,400

b) Job 25,905 5% 27,200

7(B)

a) Job 17,762 5% 18,650

b) Job 20,571 5% 21,600

Labour Charge for fishing out struck up Sub pump set /pipes /cable etc. from 165/200/250 mm bore by applying sp. Tech with sp. Tools /Fixtures by Agency.

Job Up to 150 Mtr.

Job Up to 150 Mtr.

Labour Charge for fishing out Sub pump set fallen in the tube well of size 150mm/200mm/250mm dia. Including carting of required mats, fixtures for fishing to site of work and also including carting charges of the fished out Sub pump set and accessories to the respective departmental store including loading and unloading.

Job Up to 150 Mtr.

Job Up to 150 Mtr.

S.O.R. Mech 2019-20Page 71 of 166

Section- "E"


Rates inclusive of

GST8

a) No. 17,500 Incl. 17,500 12% 19,600

b) No. 21,800 Incl. 21,800 12% 24,416

c) No. 32,000 Incl. 32,000 12% 35,840

d) No. 43,700 Incl. 43,700 12% 48,944

e) No. 55,700 Incl. 55,700 12% 62,384

f) No. 32,700 Incl. 32,700 12% 36,624

9

a) No. 13,200 Incl. 13,200 12% 14,784

b) No. 13,200 Incl. 13,200 12% 14,784

c) No. 16,850 Incl. 16,850 12% 18,872

d) No. 16,850 Incl. 16,850 12% 18,872

e) No. 17,770 Incl. 17,770 12% 19,902

10

No. 25,720 Incl. 25,720 12% 28,806

11

A

a) per KW

6,607 6,607 12% 7,400

b) per KW

5,946 5,946 12% 6,660

c) per KW

5,850 5,850 12% 6,552

d) per KW

5,600 5,600 12% 6,272

e) per KW

5,300 5,400 12% 6,048

B

a) per KW

7,598 7,598 12% 8,510

b) per KW

6,838 6,838 12% 7,659

c) per KW

6,600 6,600 12% 7,392

d) per KW

6,440 6,440 12% 7,213

e) per KW

6,095 6,095 12% 6,826

C

a) Job - 5,952 5,952 5% 6,250

b) Job - 11,905 11,905 5% 12,500

c) Job - 17,857 17,857 5% 18,750

d) Job - 23,810 23,810 5% 25,000

e) Job - 30,952 30,952 5% 32,500

12

A

a) per KW

4,910 4,910.00 12% 5,499

5 H.P.

7.5 H.P.

10.0 H.P.


Rates exclusive of GST

Providing, Supplying, Erecting approved make coupled vaccum pump set with horizontal foot mounted TEFC squirrel cage motor having under mentioned capacity working on 3ph, 50hz, 415V±10%, with base plate, DOL starter,cable,GI medium duty suction pipes-10 mtr. long, specials, valve, PVC tank of 250 ltr capacity etc. complete.Material of Constructions: Impeller- SSCF8M, Shaft- SS410, Casing-CIFG260

1 H.P.


Flow Head

10 m³/hr. 10.0 mtr.

2 H.P.

Supply of Horizontal Mono-Submersible Pump set (Drain pump) as per IS: 14220 / 1994 & its latest amendments of following duty parameters with suitable submersible motor as per IS: 9283 / 1994 & its latest amendments working on 3 ø, 415 V ± 10%, 50 ± 3% Hz power supply, rated speed 2900 RPM of following duty capacity. Material of Constructions: Impeller- High tensile brass / LTB II; Casing- CI FG 260; Pump & Motor shaft- SS 304; Bearing Bush- LTB III

3 H.P.

20 m³/hr. 10.0 mtr.

30 m³/hr. 10.0 mtr.

40 m³/hr. 10.0 mtr.

Supply, Testing & Commissioning of Horizontal Split casing centrifugal pump motor set of specified duty parameters & guaranteed efficiency of following MOC with specified capacity, horizontal foot mounted TEFC squirrel cage induction motor, working on three phase AC supply with 50 Hz ± 3%, 415 V ± 10%, rated speed 1450 RPM along with fabricated MS base frame, coupling, coupling guard, foundation bolts etc. as per relevant IS.M.O.C.: Impeller & Wearing Rings: CF8M, Casing: Cast Steel WCB , Shaft: SS 410, Shaft Sleeve: SS 410, Mechanical Seal (above 30 kW), Base Frame: MS.

Rating

31 KW to 75 KW

76 KW to 132 KW

133 KW to 315 KW

Above 315 KW

Upto 30.0 KW

50 m³/hr. 10.0 mtr.

Providing and erecting portable diesel driven self priming horizontal mono pump set (Dewatering set) with four wheel trolley, GI medium duty delivery pipes, specials, suction strainer etc. complete set Material of Constructions: Impeller-Bronze, Casing-C.I., Shaft-Carbon Steel

HSCF Pumps

Supply, Testing & Commissioning of Horizontal Split casing centrifugal pump motor set of specified duty parameters & guaranteed efficiency of following MOC with specified capacity, horizontal foot mounted TEFC squirrel cage induction motor, working on three phase AC supply with 50 Hz ± 3%, 415 V ± 10%, rated speed 1450 RPM along with fabricated MS base frame, coupling, coupling guard, foundation bolts etc. as per relevant IS.M.O.C.: Impeller & Wearing Rings: Bronze LTB II IS: 318, Casing: CI FG 260 IS: 210 , Shaft: SS 410, Shaft Sleeve: Bronze LTB II IS: 318 or SS 410, Mechanical Seal (above 30 kW) , Base Frame: MS.

12-30 LPS 6-12 mtr Head

Rating

Upto 30 KW

31.0 KW to 75.0 KW

76.0 KW to 132.0 KW

133 KW to 315 KW

Upto 30.0 KW

31.0 KW to 75.0 KW

76.0 KW to 132.0 KW

Above 315 KW

Erection Charges for Motor rating (without material supply)

133 KW to 315 KW

Above 315 KW

End Suction Back Pullout Pump

Supply, Testing & Commissioning of End Suction Back Pull-out centrifugal pump motor set with base frame of specified duty parameters & guaranteed efficiency of following MOC with specified capacity horizontal foot mounted TEFC squirrel cage induction motor, working on three phase AC supply with 50 Hz ± 3%, 415 V ± 10%, rated speed 1450 RPM along with fabricated MS base frame, coupling, coupling guard, foundation bolts etc. as per relevant IS.M.O.C.: Impeller & Wearing Rings: Bronze LTB II IS: 318, Casing: CI FG 260 IS: 210 , Shaft: SS 410, Shaft Sleeve: Bronze LTB II IS: 318 or SS 410, Mechanical Seal (above 30 kW), Base Frame: MS.

Rating

Upto 30 KW

S.O.R. Mech 2019-20Page 72 of 166

Section- "E"


Rates inclusive of

GST




b) per KW

4,400 4,400.00 12% 4,928

c) per KW

4,230 4,230.00 12% 4,738

d) per KW

3,910 3,910.00 12% 4,379

B

a) per KW

5,303 5,303 12% 5,939

b) per KW

4,752 4,752 12% 5,322

c) per KW

4,568 4,568 12% 5,117

d) per KW

4,223 4,223 12% 4,730

13

A

a) per KW

11,808 11,808 12% 13,225

b) per KW

11,808 11,808 12% 13,225

c) per KW

11,808 11,808 12% 13,225

d) per KW

11.295 11.295 12% 12.650

e) per KW

11.295 11.295 12% 12.650

B

a) per KW

11,808 Incl. 11,808 12% 13,225

b) per KW

11,808 Incl. 11,808 12% 13,225

c) per KW

11,808 Incl. 11,808 12% 13,225

d) per KW

11,295 Incl. 11,295 12% 12,650

e) per KW

11,295 Incl. 11,295 12% 12,650

C

a) Job - 31,250 31,250 5% 32,813

b) Job - 50,000 50,000 5% 52,500

c) Job - 75,000 75,000 5% 78,750

d) Job - 75,000 75,000 5% 78,750

e) Job - 75,000 75,000 5% 78,750

14

A

Nos.

a) Nos. 2,850 Incl. 2,850 12% 3,192

b) Nos. 3,400 Incl. 3,400 12% 3,808

c) Nos. 3,880 Incl. 3,880 12% 4,346

d) Nos. 5,180 Incl. 5,180 12% 5,802

e) Nos. 6,454 Incl. 6,454 12% 7,228

31 KW to 75 KW

76 KW to 132 KW

133 KW to 315 KW

Supply, Testing & Commissioning of End Suction Back Pull-out centrifugal pump motor set with base frame of specified duty parameters & guaranteed efficiency of following MOC with specified capacity horizontal foot mounted TEFC squirrel cage induction motor, working on three phase AC supply with 50 Hz ± 3%, 415 V ± 10%, rated speed 1450 RPM along with fabricated MS base frame, coupling, coupling guard, foundation bolts etc. as per relevant IS.M.O.C.: Impeller & Wearing Rings: CF8M, Casing: Cast Steel WCB , Shaft: SS 410, Shaft Sleeve: SS 410, Mechanical Seal (above 30 kW), Base Frame: MS.

Rating

Upto 30.0 KW

31.0 KW to 75.0 KW

76.0 KW to 132.0 KW

133 KW to 315 KW

76.0 KW to 132.0 KW

133 KW to 315 KW

Vertical Turbine Pumps

Supply, Testing & Commissioning of Vertical Turbine pump motor set of specified duty parameters & guaranteed efficiency of following MOC with specified capacity horizontal foot mounted TEFC squirrel cage induction motor, working on three phase AC supply with 50 Hz ± 3%, 415 V ± 10%, rated speed 1450 RPM along with column and bowl assembly, discharge head, base channel/RSJ etc. complete as per relevant IS.M.O.C.: Impeller & Sealing Rings:CF8M, Bowl & Suction Bell: CI FG 260 IS: 210 with 2% Ni , Shaft with coupling: SS 410, Column Pipe: M.S. ERW, Mechanical Seal (above 30 kW), Base Plate: MS, Line Bearing: Thordon type, Suction Strainer: S.S.

Rating

upto 30.0 KW

31.0 KW to 75.0 KW

76.0 KW to 132.0 KW

133 KW to 315 KW

Above 315 KW

Supply, Testing & Commissioning of Vertical Turbine pump motor set of specified duty parameters & guaranteed efficiency of following MOC with specified capacity horizontal foot mounted TEFC squirrel cage induction motor, working on three phase AC supply with 50 Hz ± 3%, 415 V ± 10%, rated speed 1450 RPM along with column and bowl assembly, discharge head, base channel/RSJ etc. complete as per relevant IS.M.O.C.: Impeller & Sealing Rings: CF8M, Bowl & Suction Bell: Cast Steel WCB , Shaft with coupling: SS 410, Column Pipe: M.S. Mechanical Seal (above 30 kW),ERW, , Base Plate: MS, Line Bearing: Thordon type, Suction Strainer: S.S.

Rating

Upto 30.0 KW

31.0 KW to 75.0 KW

Above 315 KW

Above 315 KW

Erection Charges for Motor rating (without material supply)

Upto 30.0 KW

31.0 KW to 75.0 KW

76.0 KW to 132.0 KW

133 KW to 315 KW

Expansion Bellows

Supply, testing & commissioning of flange ends Expansion Bellow as per EJMA standards of overall length of minimum 300 mm, designed for 15 mm axial compression and 5 mm axial extension with tie rods etc. of following MOC & pressure ratings.MOC: Bellows: SA 240 Gr. 304; Internal Sleeve: SA 240 Gr. 304; Weldends: IS 2062 Gr. B; Flanges: IS 2062 Gr. B (Drilling as per IS 1538 /IS 6392 ) & Limit Rods & Nuts: CS - IS 1367.

PN - 1.0

Size Width

NB 100 mm 300 mm

NB 125 mm 300 mm

NB 150 mm 300 mm

NB 200 mm 300 mm

NB 250 mm 300 mm

S.O.R. Mech 2019-20Page 73 of 166

Section- "E"


Rates inclusive of

GST




f) Nos. 8,500 Incl. 8,500 12% 9,520

g) Nos. 10,700 Incl. 10,700 12% 11,984

h) Nos. 13,750 Incl. 13,750 12% 15,400

i) Nos. 15,650 Incl. 15,650 12% 17,528

j) Nos. 18,500 Incl. 18,500 12% 20,720

k) Nos. 24,400 Incl. 24,400 12% 27,328

l) Nos. 31,300 Incl. 31,300 12% 35,056

m) Nos. 36,800 Incl. 36,800 12% 41,216

n) Nos. 39,980 Incl. 39,980 12% 44,778

o) Nos. 44,980 Incl. 44,980 12% 50,378

p) Nos. 73,500 Incl. 73,500 12% 82,320

q) Nos. 84,000 Incl. 84,000 12% 94,080

r) Nos. 92,927 Incl. 92,927 12% 104,078

s) Nos. 99,027 Incl. 99,027 12% 110,910

t) Nos. 106,654 Incl. 106,654 12% 119,452

u) Nos. 112,654 Incl. 112,654 12% 126,172

v) Nos. 118,580 Incl. 118,580 12% 132,810

w) Nos. 124,427 Incl. 124,427 12% 139,358

x) Nos. 130,227 Incl. 130,227 12% 145,854

y) Nos. 135,954 Incl. 135,954 12% 152,268

z) Nos. 141,627 Incl. 141,627 12% 158,622

aa) Nos. 154,227 Incl. 154,227 12% 172,734

ab) Nos. 166,754 Incl. 166,754 12% 186,764

ac) Nos. 172,280 Incl. 172,280 12% 192,954

B

Nos.

a) Nos. 3,000 Incl. 3,000 12% 3,360

b) Nos. 3,600 Incl. 3,600 12% 4,032

c) Nos. 4,080 Incl. 4,080 12% 4,570

d) Nos. 5,480 Incl. 5,480 12% 6,138

e) Nos. 6,827 Incl. 6,827 12% 7,646

f) Nos. 9,000 Incl. 9,000 12% 10,080

g) Nos. 11,100 Incl. 11,100 12% 12,432

h) Nos. 14,700 Incl. 14,700 12% 16,464

i) Nos. 17,400 Incl. 17,400 12% 19,488

j) Nos. 19,500 Incl. 19,500 12% 21,840

k) Nos. 26,000 Incl. 26,000 12% 29,120

l) Nos. 33,100 Incl. 33,100 12% 37,072

m) Nos. 39,727 Incl. 39,727 12% 44,494

n) Nos. 42,380 Incl. 42,380 12% 47,466

o) Nos. 47,680 Incl. 47,680 12% 53,402

p) Nos. 45,254 Incl. 45,254 12% 50,684

q) Nos. 88,200 Incl. 88,200 12% 98,784

r) Nos. 98,480 Incl. 98,480 12% 110,298

NB 300 mm 300 mm

NB 350 mm 300 mm

NB 400 mm 300 mm

NB 450 mm 300 mm

NB 500 mm 300 mm

NB 600 mm 300 mm

NB 700 mm 300 mm

NB 750 mm 300 mm

NB 800 mm 300 mm

NB 900 mm 300 mm

NB 1000 mm 350 mm

NB 1100 mm 350 mm

NB 1200 mm 350 mm

NB 1300 mm 350 mm

NB 1400 mm 350 mm

NB 1500 mm 350 mm

NB 1600 mm 400 mm

NB 1700 mm 400 mm

NB 1800 mm 450 mm

NB 1900 mm 450 mm

NB 2000 mm 450 mm

NB 2200 mm 500 mm

NB 2400 mm 500 mm

NB 2500 mm 550 mm

Size Width

NB 100 mm 300 mm

PN - 1.6

NB 125 mm 300 mm

NB 150 mm 300 mm

NB 200 mm 300 mm

NB 250 mm 300 mm

NB 300 mm 300 mm

NB 350 mm 300 mm

NB 400 mm 300 mm

NB 450 mm 300 mm

NB 500 mm 300 mm

NB 600 mm 300 mm

NB 700 mm 300 mm

NB 750 mm 300 mm

NB 800 mm 300 mm

NB 900 mm 300 mm

350 mm

NB 1100 mm 350 mm

NB 1000 mm

NB 1200 mm 350 mm

S.O.R. Mech 2019-20Page 74 of 166

Section- "E"


Rates inclusive of

GST




s) Nos. 104,954 Incl. 104,954 12% 117,548

t) Nos. 113,054 Incl. 113,054 12% 126,620

u) Nos. 119,380 Incl. 119,380 12% 133,706

v) Nos. 125,580 Incl. 125,580 12% 140,650

w) Nos. 131,880 Incl. 131,880 12% 147,706

x) Nos. 138,027 Incl. 138,027 12% 154,590

y) Nos. 144,080 Incl. 144,080 12% 161,370

z) Nos. 150,127 Incl. 150,127 12% 168,142

aa) Nos. 163,480 Incl. 163,480 12% 183,098

ab) Nos. 176,754 Incl. 176,754 12% 197,964

ac) Nos. 182,580 Incl. 182,580 12% 204,490

C

Nos.

a) Nos. 3,627 Incl. 3,627 12% 4,062

b) Nos. 3,927 Incl. 3,927 12% 4,398

c) Nos. 4,227 Incl. 4,227 12% 4,734

d) Nos. 5,680 Incl. 5,680 12% 6,362

e) Nos. 7,127 Incl. 7,127 12% 7,982

f) Nos. 11,250 Incl. 11,250 12% 12,600

g) Nos. 13,900 Incl. 13,900 12% 15,568

h) Nos. 18,400 Incl. 18,400 12% 20,608

i) Nos. 21,750 Incl. 21,750 12% 24,360

j) Nos. 24,400 Incl. 24,400 12% 27,328

k) Nos. 32,500 Incl. 32,500 12% 36,400

l) Nos. 38,580 Incl. 38,580 12% 43,210

m) Nos. 41,327 Incl. 41,327 12% 46,286

n) Nos. 44,080 Incl. 44,080 12% 49,370

o) Nos. 51,480 Incl. 51,480 12% 57,658

p) Nos. 92,927 Incl. 92,927 12% 104,078

q) Nos. 100,180 Incl. 100,180 12% 112,202

r) Nos. 107,327 Incl. 107,327 12% 120,206

s) Nos. 114,380 Incl. 114,380 12% 128,106

t) Nos. 123,227 Incl. 123,227 12% 138,014

u) Nos. 130,127 Incl. 130,127 12% 145,742

v) Nos. 136,880 Incl. 136,880 12% 153,306

w) Nos. 143,727 Incl. 143,727 12% 160,974

x) Nos. 150,427 Incl. 150,427 12% 168,478

y) Nos. 157,027 Incl. 157,027 12% 175,870

z) Nos. 163,627 Incl. 163,627 12% 183,262

aa) Nos. 178,180 Incl. 178,180 12% 199,562

ab) Nos. 192,627 Incl. 192,627 12% 215,742

ac) Nos. 199,027 Incl. 199,027 12% 222,910

D

Nos.

350 mm

NB 1500 mm 350 mm

NB 1900 mm

NB 1400 mm

PN - 2.0

500 mm

NB 2500 mm

NB 1300 mm 350 mm

NB 1600 mm 400 mm

NB 1700 mm 400 mm

NB 1800 mm 450 mm

450 mm

NB 2000 mm 450 mm

550 mm

Width

NB 100 mm 300 mm

NB 2200 mm 500 mm

NB 2400 mm

NB 125 mm 300 mm

Size

NB 200 mm 300 mm

NB 150 mm 300 mm

NB 250 mm 300 mm

NB 300 mm 300 mm

NB 350 mm 300 mm

NB 400 mm 300 mm

NB 450 mm 300 mm

NB 500 mm 300 mm

NB 600 mm 300 mm

NB 700 mm 300 mm

NB 750 mm 300 mm

NB 800 mm 300 mm

NB 900 mm 300 mm

NB 1000 mm 350 mm

NB 1100 mm 350 mm

NB 1200 mm 350 mm

NB 1300 mm 350 mm

NB 1400 mm 350 mm

450 mm

NB 2500 mm 550 mm

NB 1500 mm 350 mm

NB 1600 mm 400 mm

NB 1700 mm 400 mm

NB 1800 mm 450 mm

NB 1900 mm

NB 2000 mm 450 mm

NB 2200 mm 500 mm

NB 2400 mm 500 mm

PN - 2.5

Size Width

S.O.R. Mech 2019-20Page 75 of 166

Section- "E"


Rates inclusive of

GST




a) Nos. 4,500 Incl. 4,500 12% 5,040

b) Nos. 4,980 Incl. 4,980 12% 5,578

c) Nos. 5,354 Incl. 5,354 12% 5,996

d) Nos. 7,227 Incl. 7,227 12% 8,094

e) Nos. 9,054 Incl. 9,054 12% 10,140

f) Nos. 13,500 Incl. 13,500 12% 15,120

g) Nos. 16,650 Incl. 16,650 12% 18,648

h) Nos. 22,050 Incl. 22,050 12% 24,696

i) Nos. 26,100 Incl. 26,100 12% 29,232

j) Nos. 29,250 Incl. 29,250 12% 32,760

k) Nos. 39,000 Incl. 39,000 12% 43,680

l) Nos. 48,980 Incl. 48,980 12% 54,858

m) Nos. 52,480 Incl. 52,480 12% 58,778

n) Nos. 55,980 Incl. 55,980 12% 62,698

o) Nos. 65,380 Incl. 65,380 12% 73,226

p) Nos. 113,400 Incl. 113,400 12% 127,008

q) Nos. 127,227 Incl. 127,227 12% 142,494

r) Nos. 136,280 Incl. 136,280 12% 152,634

s) Nos. 145,254 Incl. 145,254 12% 162,684

t) Nos. 156,480 Incl. 156,480 12% 175,258

u) Nos. 165,254 Incl. 165,254 12% 185,084

v) Nos. 173,827 Incl. 173,827 12% 194,686

w) Nos. 182,527 Incl. 182,527 12% 204,430

x) Nos. 191,027 Incl. 191,027 12% 213,950

y) Nos. 199,427 Incl. 199,427 12% 223,358

z) Nos. 207,780 Incl. 207,780 12% 232,714

aa) Nos. 226,280 Incl. 226,280 12% 253,434

ab) Nos. 244,627 Incl. 244,627 12% 273,982

ac) Nos. 252,754 Incl. 252,754 12% 283,084

NB 200 mm 300 mm

NB 125 mm 300 mm

NB 150 mm 300 mm

300 mm

NB 2200 mm 500 mm

NB 100 mm

NB 400 mm 300 mm

NB 250 mm

NB 450 mm 300 mm

NB 500 mm 300 mm

300 mm

NB 300 mm 300 mm

NB 350 mm 300 mm

NB 600 mm 300 mm

NB 700 mm 300 mm

NB 750 mm 300 mm

NB 1400 mm 350 mm

NB 800 mm 300 mm

NB 900 mm 300 mm

NB 1000 mm 350 mm

NB 1100 mm 350 mm

450 mm

NB 1900 mm 450 mm

NB 2000 mm

NB 1200 mm 350 mm

NB 1300 mm 350 mm

NB 1500 mm 350 mm

NB 2500 mm

450 mm

NB 2400 mm 500 mm

NB 1600 mm 400 mm

NB 1700 mm 400 mm

550 mm

NB 1800 mm

S.O.R. Mech 2019-20Page 76 of 166

Section- "E"

Supply Erection & Overhead Total

15

1 Set 60,654 - 60,654 12% 67,933

2 Set 78,393 - 78,393 12% 87,800

3 Set 78,393 - 78,393 12% 87,800

4 Set 81,397 - 81,397 12% 91,165

5 Set 122,453 - 122,453 12% 137,147

6 Set 140,906 - 140,906 12% 157,815

7 Set 185,968 - 185,968 12% 208,284

8 Set 321,867 - 321,867 12% 360,491

9 Set - - - 12% -

10 Set 457,767 - 457,767 12% 512,699

11 Set - - - 12% -

12 Set 529,293 - 529,293 12% 592,808

13 Set 629,429 - 629,429 12% 704,961

14 Set 629,429 - 629,429 12% 704,961

16

1 Set 72,785 - 72,785 12% 81,519

2 Set 94,071 - 94,071 12% 105,359

3 Set 94,071 - 94,071 12% 105,359

4 Set 97,676 - 97,676 12% 109,397

5 Set 146,943 - 146,943 12% 164,576

6 Set 169,087 - 169,087 12% 189,378

7 Set 223,162 - 223,162 12% 249,941

8 Set 386,241 - 386,241 12% 432,590

9 Set - - - 12% -

10 Set 549,320 - 549,320 12% 615,239

11 Set - - - 12% -

12 Set 635,151 - 635,151 12% 711,369

13 Set 755,316 - 755,316 12% 845,954

14 Set 755,316 - 755,316 12% 845,954

17

Rates inclusive of

GST

250 kW (335 HP)

315 kW (425 HP)

POLDER TYPE SUBMERSIBLE PUMP

Providing submersible, Non clog type with required capapcity & head as per IS 8034 suitable for water having upto 10000 PPM turbidity with suitable submersible wet type, water cooled, squirrel cage motor to IS 9283, working on three phase, 50 Hz +/-3%, 415V +/- 10%, AC supply, 2900 RPM synchroNous speed with 10 mtr copper conductor flat cable from pump to starter panel with cable end terminations (4) all supports, clamps, pipe fittings alongwith mechanical seal, bearing bush, strainer etc. complete set & following M.O.C: Casing CI, SS CF8M impeller, Bronze: wearing ring & Bearing bush, TC mechanical seal, CS/S.S.bearing, S.S shaft with sleeve, SS strainer & MS motor body.

75 kW (100 HP)

90 kW (120 HP)

110 kW (150 HP)

125/132 kW (170/180 HP)

150/160 kW (200/215 HP)

180/200 kW (240/270 HP)

Up to 18.5 kW (25 HP)

22 kW (30 HP)

30 kW (40 HP)

37 kW (50 HP)

45 kW (60 HP)

55 kW (75 HP)

150/160 kW (200/215 HP)

180/200 kW (240/270 HP)

250 kW (335 HP)

315 kW (425 HP)

SEWAGE NoN CLOG, END SUCTION TYPE VERTICAL CENTRIFUGAL PUMP

Supply of non clog seweage vertically mounted end suction type vertical centrifugal pump set of required capapcity & head with suitable TEFC squirrel cage foot mounted induction motor working on three phase 50 Hz ± 3%, 415V ± 10% AC supply, 1500 RPM synchronous speed including suitable provision of extended shaft of 2 meters length to couple with motor along with base frame, coupling with guard, foundation bolts, strainer etc. complete set as per relevant IS & following M.O.C: Casing: 1.5 to 2% Ni. C.I; Impeller & wearing ring: SS / CF8M, Shaft with sleeve: S.S. & Base frame: C. I; Guide Pipe: S. S.

45 kW (60 HP)

55 kW (75 HP)

75 kW (100 HP)

90 kW (120 HP)

110 kW (150 HP)

125/132 kW (170/180 HP)


SEWAGE NoN CLOG, END SUCTION TYPE HORIZONTAL CENTRIFUGAL PUMP

Supply of non clog sewage end suction type horizontal centrifugal pump set of required capapcity & head with suitable TEFC squirrel cage foot mounted induction motor working on three phase 50 Hz ± 3%, 415V ± 10% AC supply, 1500 RPM synchronous speed along with base frame, coupling with guard, foundation bolts, strainer etc. complete set as per relevant IS & following M.O.C: Casing: 1.5 to 2% Ni. C.I; Impeller & wearing ring: SS-CF8M, Shaft with sleeve: S.S. & Base frame: C.I., Guide Pipe: SS.

Up to 18.5 kW (25 HP)

22 kW (30 HP)



30 kW (40 HP)

37 kW (50 HP)


S.O.R. Mech 2019-20Page 77 of 166

Section- "E"


Rates inclusive of

GST

Prevailing rates of GST Sr. No. Description of Item Unit



1 Set 67,600 - 67,600 12% 75,712

2 Set 71,700 - 71,700 12% 80,304

3 Set 80,600 - 80,600 12% 90,272

4 Set 88,000 - 88,000 12% 98,560

5 Set 101,500 - 101,500 12% 113,680

6 Set 139,514 - 139,514 12% 156,256

7 Set 144,464 - 144,464 12% 161,799

8 Set 172,200 - 172,200 12% 192,864

9 Set 180,900 - 180,900 12% 202,608

10 Set 330,900 - 330,900 12% 370,608

11 Set 297,098 - 297,098 12% 332,750

12 Set 343,446 - 343,446 12% 384,660

13 Set 412,500 - 412,500 12% 462,000

14 Set 463,950 - 463,950 12% 519,624

18

1 Set 121,957 - 121,957 12% 136,592

2 Set 136,099 - 136,099 12% 152,431

3 Set 157,886 - 157,886 12% 176,832

4 Set 173,052 - 173,052 12% 193,818

5 Set 229,187 - 229,187 12% 256,690

6 Set 253,436 - 253,436 12% 283,849

7 Set 318,050 - 318,050 12% 356,216

8 Set 329,905 - 329,905 12% 369,494

9 Set 404,131 - 404,131 12% 452,627

10 Set 556,606 - 556,606 12% 623,399

11 Set 584,801 - 584,801 12% 654,977

12 Set 659,668 - 659,668 12% 738,828

13 Set 957,106 - 957,106 12% 1,071,959

14 Set 990,214 - 990,214 12% 1,109,040

19

19.1

Each 96,120 24,543 120,663 18% 142,383

50 HP

60 HP

75 HP

100 HP

12.5 HP

15 HP

20 HP

25 HP

30 HP

40 HP

SUBMERSIBLE SEWAGE NON-CLOG VERTICAL PUMP

Providing sewage submersible, Non clog type suitable for working on Air filled Dry type motor, three phase, 50 Hz +/-3%, 415V +/- 10%, AC supply, 1500 RPM synchronous speed with 3 core flat copper cable from pump to starter panel with cable end terminations (4) all supports, clamps, pipe fittings alongwith mechanical seal, bearing bush, strainer etc. complete set & following M.O.C: Casing CI, SS CF8M impeller, Bronze: wearing ring & Bearing bush, TC mechanical seal, CS/S.S.bearing, S.S shaft with sleeve, SS strainer & MS motor body.

Upto 3 Hp

5 HP

7.5 HP

10 HP

30 HP

40 HP

50 HP

60 HP

75 HP

100 HP

7.5 HP

10 HP

12.5 HP

15 HP

20 HP

25 HP

Upto 3 HP

5 HP

11 kV Double Pole Structure Assembly

11 KV Double / Four Pole Structure Assembly

11 kV Two Pole Structure Assembly:SITC of 11 kV double pole 9 mtr. high structure made of 6" X 3" 'I" section girder, 4" X 2" channels, clamps, nuts, bolts, stay wires including earthing system with following accessories duly connected with ACSR conductors as per approved drawing & in compliance with requirement of IEC.(a) 11 kV, 200 A drop out fuses with Synthetic Resin Bonded Paper (SRBP) tubes: 1 Set (01 piece per phase).(b) 11 kV, 400 A G.O.D. switch complete with earth switch, insulators, operating handle with galvanised pipe, square bar: 1 Set.(c) 11 kV lightning arrestor with clamps: 3 Nos.(d) 11 kV Disc Insulators (70KN): 3 Nos. (e) 11 kV Pin Insulators (5KN): 3 Nos. (f) 20 mm dia. GI. Stay Sets Complete: 2 Set.

S.O.R. Mech 2019-20Page 78 of 166

Section- "E"


Rates inclusive of

GST




19.2

Each 116,640 34,542 151,182 18% 178,395

20

20.1

20.1.1

Voltage Ratio (kV)(11/0.433), (6.6/433) &

(3.3/0.433)

Rating (kVA)

a Eff. Level-2 Set 350,997 30,000 380,997 18% 449,576

b Eff. Level-3 Set 386,097 30,000 416,097 18% 490,994

c Eff. Level-2 Set 412,860 30,000 442,860 18% 522,575

d Eff. Level-3 Set 454,146 30,000 484,146 18% 571,292

e Eff. Level-2 250 Set 491,593 30,000 521,593 18% 615,480

f Eff. Level-3 Set 540,752 30,000 570,752 18% 673,488

g Eff. Level-2 Set 581,574 30,000 611,574 18% 721,658

h Eff. Level-3 Set 639,732 30,000 669,732 18% 790,283

i Eff. Level-2 Set 659,757 35,000 694,757 18% 819,814

j Eff. Level-3 Set 725,733 35,000 760,733 18% 897,665

k Eff. Level-2 Set 715,996 35,000 750,996 18% 886,175

l Eff. Level-3 Set 787,595 35,000 822,595 18% 970,662

m Eff. Level-2 Set 839,720 35,000 874,720 18% 1,032,170

n Eff. Level-3 Set 923,692 35,000 958,692 18% 1,131,257

o Eff. Level-2 Set 873,523 40,000 913,523 18% 1,077,957

p Eff. Level-3 Set 960,875 40,000 1,000,875 18% 1,181,033

q Eff. Level-2 Set 1,003,940 40,000 1,043,940 18% 1,231,850

r Eff. Level-3 Set 1,104,334 40,000 1,144,334 18% 1,350,314

20.1.2

11 kV Four Pole Structure Assembly

With off circuit tap changer ± 7.5% in steps of 2.5%

Maximum Total Losses

(kW)@ 50% /

@ 100% / % Imp

160

Transformer

SITC of outdoor type, three phase, oil immerged, distribution transformer of required KVA & voltage ratio, copper double wound, vector group -Dyn11, HV delta connected & LV star connected with neutral brought out connected to provide separate earthing terminals, bushing / cable box onHV side and cable box on LV side suitable for cables or bus duct as per requirement with standard fittings, conforming to IS: 1180 (Part-1) / 2014 withits latest amendment including first fill of transformer oil & following accessories.(a) Oil conservator with filling holes with cap and prismatic oil level gauge.(b) Silica Gel dehydrating breather charged with silica gel(c) Oil drain cum sampling valve with plug(d) Oil filter valve(e) Lifting Eyes / Hooks / Lugs(f) Two earthing terminal(g) Diagram and rating plate(h) Air release plug(i) Explosion vent with diaphragm(j) Thermometer pocket(k) Four bi-directional plain roller with base channel with hauling holes(l) Fixed / Separate type radiator banks(m) Off circuit externally operated tapping switch (For rating < 1000 kVA)(n) 100 mm stem type oil temperature indicator (For rating < 500 kVA)(o) Bucholtz relay with shut off valve (For rating ≥ 500 KVA)(p) 150 mm dial type oil temperature indicator with Alarm / Trip contact (For rating ≥ 500 kVA)(q) 150 mm dial type winding temperature indicator with Alarm / Tip contact (For rating ≥ 1000 kVA)(r) Marshalling box (For rating ≥ 500 kVA)(s) 150 mm dia. magnetic type oil gauge (For rating ≥ 1600 kVA)(t) Inspection cover & Jacking lugs (For rating ≥ 1600 kVA)

11 kV Four Pole Structure Assembly:SITC of 11 kV double pole 9 mtr. high structure made of 6" X 3" 'I" section girder, 4" X 2" channels, clamps, nuts, bolts, stay wires including earthing system with following accessories duly connected with ACSR conductors as per approved drawing & in compliance with requirement of IEC.(a) 11 kV, 200 A drop out fuses with Synthetic Resin Bonded Paper (SRBP) tubes: 2 Set (01 piece per phase/circuit).(b) 11 kV, 400 A G.O.D. switch complete with earth switch, insulators, operating handle with galvanised pipe, square bar: 2 Set.(c) 11 kV lightning arrestor with clamps: 3 Nos.(d) 11 kV Disc Insulators (70KN): 9 Nos. (e) 11 kV Pin Insulators (5KN): 6 Nos. (f) 20 mm dia. GI. Stay Sets Complete: 2 Set

0.67/ 1.95/ 4.5

0.57/ 1.7/ 4.5

200 0.78/ 2.3/ 4.5

0.67/ 2.1/ 4.5

315 1.02/ 3.1/ 4.5

0.95/ 2.75/ 4.5

0.98/ 2.93/ 4.5

0.92/ 2.7/ 4.5

400 1.25/ 3.45/ 4.5

1.15/ 3.3/ 4.5

500 1.51/ 4.3/ 4.5

1.43/ 4.1/ 4.5

630 1.86/ 5.3/ 4.5

1.74/ 4.85/ 4.5

800 2.28/ 6.4/ 5.0

2.14/ 5.83/ 5.0

1000 2.7/ 7.7/ 5.0

2.62/ 7.0/ 5.0

With on load tap changer ± 10% steps of 1.25% with RTCC & AVR.

S.O.R. Mech 2019-20Page 79 of 166

Section- "E"


Rates inclusive of

GST




Voltage Ratio (kV)(11/0.433), (6.6/433) &

(3.3/0.433)

Rating (kVA)

a Eff. Level-2 Set 1,580,415 50,000 1,630,415 18% 1,923,890

b Eff. Level-3 Set 1,738,457 50,000 1,788,457 18% 2,110,379

c Eff. Level-2 Set 1,637,960 50,000 1,687,960 18% 1,991,793

d Eff. Level-3 Set 1,801,756 50,000 1,851,756 18% 2,185,073

e Eff. Level-2 Set 1,854,261 50,000 1,904,261 18% 2,247,028

f Eff. Level-3 Set 2,039,687 50,000 2,089,687 18% 2,465,831

g Eff. Level-2 Set 2,065,220 60,000 2,125,220 18% 2,507,760

h Eff. Level-3 Set 2,271,743 60,000 2,331,743 18% 2,751,456

i Eff. Level-2 Set 2,335,597 60,000 2,395,597 18% 2,826,805

j Eff. Level-3 Set 2,569,157 60,000 2,629,157 18% 3,102,405

20.2

20.2.1

Voltage Ratio (kV) Rating (kVA)

a 11/3.3 160 Set 256,200 30,000 286,200 18% 337,716

b 11/3.3 200 Set 298,123 30,000 328,123 18% 387,185

c 11/3.3 250 Set 330,730 30,000 360,730 18% 425,662

d 11/3.3 315 Set 367,996 35,000 402,996 18% 475,535

e 11/3.3 400 Set 433,210 35,000 468,210 18% 552,488

f 11/3.3 500 Set 517,057 35,000 552,057 18% 651,428

g 11/3.3 630 Set 596,246 35,000 631,246 18% 744,871

h 11/3.3 750 Set 656,803 40,000 696,803 18% 822,227

i 11/3.3 800 Set 698,726 40,000 738,726 18% 871,697

j 11/3.3 1000 Set 791,890 40,000 831,890 18% 981,630

k 11/6.6 160 Set 246,883 30,000 276,883 18% 326,722

l 11/6.6 200 Set 293,465 30,000 323,465 18% 381,689

m 11/6.6 250 Set 326,072 30,000 356,072 18% 420,165

n 11/6.6 315 Set 363,338 35,000 398,338 18% 470,038

o 11/6.6 400 Set 428,552 35,000 463,552 18% 546,991

p 11/6.6 500 Set 512,399 35,000 547,399 18% 645,931

q 11/6.6 630 Set 591,588 35,000 626,588 18% 739,374

r 11/6.6 750 Set 652,145 40,000 692,145 18% 816,731

s 11/6.6 800 Set 689,410 40,000 729,410 18% 860,704

t 11/6.6 1000 Set 981,012 40,000 1,021,012 18% 1,204,794

20.2.2

1250 3.3/ 9.20/ 5.0

3.2/ 8.44/ 5.0

Maximum Total Losses (kW)

@ 50% Load /1000 2.79/ 7.7/ 5.0

3.3/ 9.2/ 5.0

2500 6.15/ 18.5/ 6.25

5.9/ 17.5/ 6.25

SITC of outdoor type, three phase, oil immerged, power transformer of required KVA & voltage ratio, copper double wound, vector group - Dyn11, HV delta connected & LV star connected with neutral brought out connected to provide separate earthing terminals, bushing / cable box on HV side and cable box on LV side suitable for cables or bus duct as per requirement with standard fittings, conforming to IS: 2026 - 2011 with its latest amendment including first fill of transformer oil & following accessories.(a) Oil conservator with filling holes with cap and prismatic oil level gauge. (b) Silica Gel dehydrating breather charged with silica gel (c) Oil drain cum sampling valve with plug (d) Oil filter valve (e) Lifting Eyes / Hooks / Lugs (f) Two earthing terminal (g) Diagram and rating plate (h) Air release plug (i) Explosion vent with diaphragm (j) Thermometer pocket(k) Four bi-directional plain roller with base channel with hauling holes (l) Fixed / Separate type radiator banks (m) Off circuit externally operated tapping switch (For rating < 1000 kVA)(n) 100 mm stem type oil temperature indicator (For rating < 500 kVA) (o) Bucholtz relay with shut off valve (For rating ≥ 500 KVA) (p) 150 mm dial type oil temperature indicator with Alarm / Trip contact (For rating ≥ 500 kVA) (q) 150 mm dial type winding temperature indicator with Alarm / Tip contact (For rating ≥ 1000 kVA) (r) Marshalling box (For rating ≥ 500 kVA)(s) 150 mm dia. magnetic type oil gauge (For rating ≥ 1600 kVA) (t) Inspection cover & Jacking lugs (For rating ≥ 1600 kVA)

1600 4.2/ 11.8/ 6.25

3.97/ 11.3/ 6.25

2000 5.05/ 15.0/ 6.25

4.79/ 14.1/ 6.25

With off circuit tap changer ± 7.5% in steps of 2.5%

Maximum Losses (kW)

As perCBIP Manual

With on load tap changer ± 10% in steps of 1.25% with RTCC & AVR

S.O.R. Mech 2019-20Page 80 of 166

Section- "E"


Rates inclusive of

GST




Voltage Ratio (kV) Rating (kVA)

Maximum

Losses (kW)

No Load Loss

& Load Loss

a 11/3.3 1000 Set 1,183,176 40,000 1,223,176 18% 1,443,348

b 11/3.3 1250 Set 1,403,974 50,000 1,453,974 18% 1,715,689

c 11/3.3 1600 Set 1,467,325 50,000 1,517,325 18% 1,790,444

d 11/3.3 2000 Set 1,720,730 50,000 1,770,730 18% 2,089,461

e 11/3.3 2500 Set 1,788,739 60,000 1,848,739 18% 2,181,512

f 11/3.3 3150 Set 1,937,801 70,000 2,007,801 18% 2,369,205

g 11/3.3 3500 Set 2,156,735 70,000 2,226,735 18% 2,627,547

h 11/3.3 4000 Set 2,343,062 70,000 2,413,062 18% 2,847,413

i 11/6.6 1000 Set 1,173,860 40,000 1,213,860 18% 1,432,355

j 11/6.6 1250 Set 1,280,998 50,000 1,330,998 18% 1,570,578

k 11/6.6 1600 Set 1,462,667 50,000 1,512,667 18% 1,784,947

l 11/6.6 2000 Set 1,597,754 50,000 1,647,754 18% 1,944,350

m 11/6.6 2500 Set 1,784,081 60,000 1,844,081 18% 2,176,016

n 11/6.6 3150 Set 1,933,143 70,000 2,003,143 18% 2,363,708

o 11/6.6 3500 Set 2,147,419 70,000 2,217,419 18% 2,616,554

p 11/6.6 4000 Set 2,343,062 70,000 2,413,062 18% 2,847,413

q 66/6.6 5000 Set 3,423,759 80,000 3,503,759 18% 4,134,435

r 66/6.6 6300 Set 4,038,638 80,000 4,118,638 18% 4,859,993

s 66/6.6 7500 Set 4,085,219 90,000 4,175,219 18% 4,926,759

t 66/6.6 10000 Set 4,085,219 90,000 4,175,219 18% 4,926,759

u 66/6.6 12500 Set 5,030,829 100,000 5,130,829 18% 6,054,378

v 66/6.6 15000 Set 5,818,061 110,000 5,928,061 18% 6,995,111

w 66/6.6 20000 Set 6,768,328 120,000 6,888,328 18% 8,128,227

x 66/11 5000 Set 3,433,075 80,000 3,513,075 18% 4,145,428

y 66/11 6300 Set 4,052,612 80,000 4,132,612 18% 4,876,482

z 66/11 7500 Set 4,099,194 90,000 4,189,194 18% 4,943,249

aa 66/11 10000 Set 4,565,011 100,000 4,665,011 18% 5,504,713

ab 66/11 12500 Set 4,993,564 100,000 5,093,564 18% 6,010,405

ac 66/11 15000 Set 5,832,035 110,000 5,942,035 18% 7,011,601

ad 66/11 20000 Set 6,791,619 120,000 6,911,619 18% 8,155,711

ae 11/0.433 3150 Set 2,142,761 70,000 2,212,761 18% 2,611,057

af 11/0.433 3500 Set 2,387,781 70,000 2,457,781 18% 2,900,181

ag 11/0.433 4000 Set 2,515,415 70,000 2,585,415 18% 3,050,789

20.3

20.3.1

System Voltage (Pri)/Tap Switch

Transformer Rating (kVA)

a 160 Set 30,000 - 30,000 18% 35,400

b 200 Set 30,000 - 30,000 18% 35,400

As perCBIP Manual

Casting of transformer plinth / foundation including oil soak pit (where required) in situ reinforced cement concrete in M 20 using granite, quartzite trap metal of size 6 mm to 20 mm for RCC work including providing of 53 grade cement & Fe 415 grade TMT bars, scaffolding, centering, form work, curing etc. complete.

RCC plinth / foundation for transformer of capacity ≤ 315 KVA.

Plinth Dimensions (L x W x H)

up to 11 kV/ OCTC 1250x1250x 1500

1250x1250x 1500

S.O.R. Mech 2019-20Page 81 of 166

Section- "E"


Rates inclusive of

GST




c 250 Set 30,000 - 30,000 18% 35,400

d 315 Set 30,000 - 30,000 18% 35,400

20.3.2



a 400 Set 35,000 - 35,000 18% 41,300

b 500 Set 35,000 - 35,000 18% 41,300

c 630 Set 35,000 - 35,000 18% 41,300

20.3.3



a 750 Set 40,000 - 40,000 18% 47,200

b 800 Set 40,000 - 40,000 18% 47,200

c 1000 Set 40,000 - 40,000 18% 47,200

20.3.4

System Voltage(Pri)/Tap Switch


a 1000 Set 50,000 - 50,000 18% 59,000

b 1250 Set 50,000 - 50,000 18% 59,000

c 1600 Set 50,000 - 50,000 18% 59,000

20.3.5



a 2000 Set 60,000 - 60,000 18% 70,800

b 2500 Set 60,000 - 60,000 18% 70,800

20.3.6 RCC plinth / foundation for transformer of capacity ˃2500 & ≤4000 KVA.



a 3150 Set 70,000 - 70,000 18% 82,600

b 3500 Set 70,000 - 70,000 18% 82,600

c 4000 Set 70,000 - 70,000 18% 82,600

20.3.7



a 5000 Set 80,000 - 80,000 18% 94,400

b 6300 Set 80,000 - 80,000 18% 94,400

c 7500 Set 80,000 - 80,000 18% 94,400

d 10000 Set 80,000 - 80,000 18% 94,400

20.3.8

1250x1250x 1500

1250x1250x 1500

RCC plinth / foundation for distribution transformer of capacity ˃1600 & ≤2500 KVA.

RCC plinth / foundation for transformer of capacity ˃315 & ≤ 630 KVA.


up to 33 kV/ OCTC 1500x1500x 1500

1500x1500x 1500

1500x1500x 1500

RCC plinth / foundation for transformer of capacity ˃630 & ≤1000 KVA.


up to 33 kV/ OCTC 1750x1750x 1000

1750x1750x 1000

1500x1500x 1500

RCC plinth / foundation for distribution transformer of capacity ≥1000 & ≤1600 KVA.


up to 33 kV/ OLTC 1750x1750x 1000

1750x1750x 1000

1750x1750x 1000

Plinth Dimensions

(L X W X H)

up to 33 kV/ OLTC 2000 x 2000 x 1000

2000 x 2000 x 1000

Plinth Dimensions

(L X W X H)

2000 x 2000 x 1000

up to 66 kV/ OLTC 2250 x 2250 x 1000

2250 x 2250 x 1000

2250 x 2250 x 1000


Plinth Dimensions

(L X W X H)

up to 66 kV/ OLTC 2500 x 2500 x 500

2500 x 2500 x 500

2500 x 2500 x 500

2500 x 2500 x 500


S.O.R. Mech 2019-20Page 82 of 166

Section- "E"


Rates inclusive of

GST






a 12500 Set 90,000 - 90,000 18% 106,200

b 15000 Set 90,000 - 90,000 18% 106,200

c 20000 Set 90,000 - 90,000 18% 106,200

21

a) No. 12,758 4,545 17,303 18% 20,418

b) No. 13,749 4,545 18,294 18% 21,587

c) No. 13,749 4,545 18,294 18% 21,587

d) No. 13,749 4,545 18,294 18% 21,587

e) No. 18,148 4,545 22,693 18% 26,778

f) No. 21,668 4,545 26,213 18% 30,931

g) No. 29,147 4,545 33,692 18% 39,757

h) No. 35,196 4,545 39,741 18% 46,894

i) No. 42,895 4,545 47,440 18% 55,979

j) No. 47,294 4,545 51,839 18% 61,170

k) No. 70,153 4,545 74,698 18% 88,144

l) No. 75,114 4,545 79,659 18% 93,998

m) No. 88,319 4,545 92,864 18% 109,580

n) No. 97,263 4,545 101,808 18% 120,133

o) No. 122,374 4,545 126,919 18% 149,764

p) No. 137,481 4,545 142,026 18% 167,591

q) No. 173,777 4,545 178,322 18% 210,420

r) No. 195,773 4,545 200,318 18% 236,375

s) No. 263,963 4,545 268,508 18% 316,839

t) No. 285,960 4,545 290,505 18% 342,796

u) No. 307,958 4,545 312,503 18% 368,754

v) No. 422,963 4,545 427,508 18% 504,459

w) No. 503,083 4,545 507,628 18% 599,001

22

22.1

a No 33,539 4,545 38,084 18% 44,939

7.5 kW

11 kW

Plinth Dimensions

(L X W X H)

up to 66 kV/ OLTC 3000 x 2500 x 500

3000 x 2500 x 500

3000 x 2500 x 500

Microprocessor Based LV Variable Frequency Drive

Supplying, erecting, commissioning of 415 V Fully automatic microprocessor based Variable Frequency drive for pump control application as per general specification as under:The VFD unit shall have modular construction, 6 Pulse Bridge rectifier, speed control by means of sensorless vector control (open loop), high torque at low frequencies, locking at high and low frequency settings, In-built PID control, frequency accuracy of ± 0.1 % (min), frequency resolution of ± 0.1 Hz (min), protections against; a) overload (motor and drive), b) short circuit, c) ground fault, d) input/ output phase loss (open circuit), e) stalling, f) input/ output undervoltage (momentary power loss restart), g) input/ output overvoltage, h) over-frequency, i) Input surge, j) over temperature of heatsink, k) loss of remote speed signal etc. The VFD shall also have user-friendly programming software & it shall be capable of at least two level parameter setting with password lock for critical parameters, programming for I/Os, speed search function, copy parameters (upload/download) to other identical unit, tuning to energy saving mode (maximum efficiency), event/fault recording (last 5 faults in non-volatile memory) & RS485 communication port (MODBUS RTU protocol) with required software.

2.2 kW

3 kW

4 kW

5.5 kW

18.5 kW

22 kW

30 kW

37 kW

15 kW

45 kW

55 kW

75 kW

90 kW

110 kW

132 kW

160 kW

200 kW

250 kW

315 kW

355 kW

400 kW

Microprocessor Based LV Soft Starter

Supplying, erecting & commissioning of 415 V Fully automatic Microprocessor based soft starter with external bypass arrangement for pump control application as per general specification as under:Control Method -Torque Control, Input voltage- 415V, 3 Phase, Input frequency -50/ 60 Hz (±5%), Confirmative to standard - IEC 61947-4-2UL,CSA,CE, Motor protection - inbuilt Thermal Protection, Starter protection - SC UV, Phase unbalance, Phase failure, EMC Std- IEC 61000-4-2 Level-3 & IEC 61000-4-3-Level-3, Built in communication as per RS 485. 30 kW

S.O.R. Mech 2019-20Page 83 of 166

Section- "E"


Rates inclusive of

GST




b No 38,198 4,545 42,743 18% 50,437

c No 45,651 4,545 50,196 18% 59,231

d No 48,446 4,545 52,991 18% 62,529

e No 55,899 4,545 60,444 18% 71,324

f No 59,625 4,545 64,170 18% 75,721

g No 70,805 4,545 75,350 18% 88,913

h No 78,258 4,545 82,803 18% 97,708

i No 101,549 4,545 106,094 18% 125,191

j No 194,340 4,545 198,885 18% 234,684

k No 229,555 4,545 234,100 18% 276,238

l No 288,901 4,545 293,446 18% 346,266

m No 325,421 4,545 329,966 18% 389,360

n No 325,421 4,545 329,966 18% 389,360

22.2

a No 27,950 4,545 32,495 18% 38,344

b No 30,744 4,545 35,289 18% 41,641

c No 32,608 4,545 37,153 18% 43,841

d No 36,334 4,545 40,879 18% 48,237

e No 43,787 4,545 48,332 18% 57,032

f No 46,582 4,545 51,127 18% 60,330

g No 54,035 4,545 58,580 18% 69,124

h No 61,488 4,545 66,033 18% 77,919

i No 77,326 4,545 81,871 18% 96,608

j No 102,480 4,545 107,025 18% 126,290

k No 115,523 4,545 120,068 18% 141,680

l No 128,566 4,545 133,111 18% 157,071

m No 166,763 4,545 171,308 18% 202,143

n No 166,763 4,545 171,308 18% 202,143

23

23.1

a Meter 49 6 55 18% 65

b Meter 49 6 55 18% 65

c Meter 57 6 63 18% 74

d Meter 71 6 77 18% 91

e Meter 76 6 82 18% 97

f Meter 96 6 102 18% 120

g Meter 121 8 129 18% 152

110 kW

132 kW

37 kW

45 kW

55 kW

75 kW

90 kW

160 kW

355 kW

220 kW

250 kW

315 kW

355 kW

37 kW

45 kW

1.1 kV Grade Cable- Aluminium / Copper Conductor

Supply, laying, testing & commissioning 1.1 kV grade, XLPE insulated, stranded Aluminium conductor, galvanised steel flat strip / round wire armoured, extruded PVC type ST2 sheathed, heavy duty cable (to be laid on wall surface with necessary clamps / in existing cable trench / cable trays / conduit / pipe sleeves at road crossing or floor as per site requirement) conforming to IS:7098 (Part-1) & IEC:60502 (Part-1) of following sizes:

400 kW

Supplying, erecting & commissioning of 415 V Fully automatic Microprocessor based soft starter with built in bypass arrangement for pump control application as per general specification as under:Control Method -Torque Control, Input voltage- 415V, 3 Phase, Input frequency - 50/ 60 Hz (±5%), Confirmative to standard - IEC 61947-4-2UL,CSA,CE, Motor protection - inbuilt Thermal Protection, Starter protection - SC UV, Phase unbalance, Phase failure, EMC Std- IEC 61000-4-2 Level-3 & IEC 61000-4-3-Level-3, Built in communication as per RS 485.

160 kW

75 kW

90 kW

3 Core x 2.5 Sq mm

220 kW

250 kW

315 kW

400 kW

30 kW

55 kW

110 kW

132 kW

3 Core x 4.0 Sqmm

3 Core x 6.0 Sqmm

3 Core x 10 Sqmm

3 Core x 16 Sqmm

3 Core x 25 Sqmm

3 Core x 35 Sqmm

S.O.R. Mech 2019-20Page 84 of 166

Section- "E"


Rates inclusive of

GST




h Meter 153 8 161 18% 190

i Meter 206 12 218 18% 257

j Meter 256 12 268 18% 316

k Meter 305 12 317 18% 374

l Meter 376 12 388 18% 458

m Meter 460 18 478 18% 564

n Meter 588 18 606 18% 715

o Meter 711 18 729 18% 860

p Meter 903 24 927 18% 1,094

q Meter 1,223 24 1,247 18% 1,472

r Meter 1,622 24 1,646 18% 1,943

23.2

a Meter 108 12 120 18% 142

b Meter 136 12 148 18% 175

c Meter 177 12 189 18% 223

d Meter 240 17 257 18% 303

e Meter 290 17 307 18% 362

f Meter 362 17 379 18% 447

g Meter 428 23 451 18% 532

h Meter 534 23 557 18% 658

i Meter 672 29 701 18% 828

j Meter 824 29 853 18% 1,007

k Meter 1,048 35 1,083 18% 1,278

l Meter 1,426 35 1,461 18% 1,724

m Meter 1,936 36 1,972 18% 2,327

23.3

a Meter 57 6 63 18% 74

b Meter 57 6 63 18% 74

c Meter 64 6 70 18% 83

d Meter 81 6 87 18% 103

e Meter 91 6 97 18% 115

f Meter 116 6 122 18% 144

g Meter 151 12 163 18% 192

h Meter 195 12 207 18% 244

i Meter 264 12 276 18% 326

j Meter 322 12 334 18% 394

k Meter 395 18 413 18% 488

l Meter 485 18 503 18% 594

3 Core x 50 Sqmm

3 Core x 70 Sqmm

3 Core x 95 Sqmm

3 Core x 120 Sqmm

3 Core x 150 Sqmm

3 Core x 185 Sqmm

3 Core x 240 Sqmm

3 Core x 300 Sqmm

3 Core x 400 Sqmm

3 Core x 500 Sqmm

3 Core x 630 Sqmm


3.5 Core x 500 Sqmm

3.5 Core x 25 Sqmm

3.5 Core x 35 Sqmm

3.5 Core x 50 Sqmm

3.5 Core x 70 Sqmm

3.5 Core x 95 Sqmm

3.5 Core x 120 Sqmm

3.5 Core x 630 Sqmm


4 Core x 2.5 Sqmm

4 Core x 4.0 Sqmm

3.5 Core x 150 Sqmm

3.5 Core x 185 Sqmm

3.5 Core x 240 Sqmm

3.5 Core x 300 Sqmm

3.5 Core x 400 Sqmm

4 Core x 10 Sqmm

4 Core x 16 Sqmm

4 Core x 25 Sqmm

4 Core x 35 Sqmm

4 Core x 50 Sqmm

4 Core x 70 Sqmm

4 Core x 95 Sqmm

4 Core x 120 Sqmm

4 Core x 150 Sqmm

4 Core x 6.0 Sqmm

S.O.R. Mech 2019-20Page 85 of 166

Section- "E"


Rates inclusive of

GST




m Meter 603 18 621 18% 733

n Meter 770 24 794 18% 937

o Meter 927 24 951 18% 1,122

p Meter 1,179 24 1,203 18% 1,420

q Meter 1,600 24 1,624 18% 1,917

r Meter 2,164 24 2,188 18% 2,582

23.4

a Meter 64 6 70 18% 83

b Meter 85 6 91 18% 107

c Meter 117 6 123 18% 145

d Meter 179 6 185 18% 218

e Meter 254 6 260 18% 307

f Meter 417 12 429 18% 506

g Meter 574 12 586 18% 692

h Meter 782 12 794 18% 937

i Meter 1,110 12 1,122 18% 1,324

j Meter 1,594 12 1,606 18% 1,895

k Meter 2,003 18 2,021 18% 2,385

l Meter 2,500 18 2,518 18% 2,971

m Meter 3,076 18 3,094 18% 3,651

n Meter 3,963 24 3,987 18% 4,705

o Meter 4,932 24 4,956 18% 5,848

p Meter 5,659 24 5,683 18% 6,706

23.5

a Meter 502 12 514 18% 607

b Meter 658 12 670 18% 791

c Meter 914 12 926 18% 1,093

d Meter 1,293 17 1,310 18% 1,546

e Meter 1,862 17 1,879 18% 2,217

f Meter 2,386 17 2,403 18% 2,836

g Meter 2,883 23 2,906 18% 3,429

h Meter 3,596 23 3,619 18% 4,271

i Meter 4,619 29 4,648 18% 5,485

j Meter 5,754 29 5,783 18% 6,824

k Meter 7,485 35 7,520 18% 8,874

23.6

4 Core x 185 Sqmm

4 Core x 240 Sqmm

4 Core x 300 Sqmm

4 Core x 400 Sqmm

4 Core x 500 Sqmm

4 Core x 630 Sqmm

Supply, laying, testing & commissioning 1.1 kV grade, XLPE insulated, stranded Copper conductor, galvanised steel flat strip / round wire armoured, extruded PVC type ST2 sheathed, heavy duty cable (to be laid on wall surface with necessary clamps / in existing cable trench / cable trays / conduit / pipe sleeves at road crossing or floor as per site requirement) conforming to IS:7098 (Part-1) & IEC:60502 (Part-1), of following sizes:

3 Core x 2.5 Sqmm

3 Core x 4.0 Sqmm

3 Core x 6.0 Sqmm

3 Core x 10 Sqmm

3 Core x 16 Sqmm

3 Core x 25 Sqmm

3 Core x 35 Sqmm

3 Core x 50 Sqmm

3 Core x 70 Sqmm

3 Core x 95 Sqmm

3 Core x 120 Sqmm

3 Core x 150 Sqmm

3 Core x 185 Sqmm

3 Core x 240 Sqmm

3 Core x 300 Sqmm

3 Core x 400 Sqmm

Supply, laying, testing & commissioning of 1.1 kV grade, XLPE insulated, stranded Copper conductor, galvanised steel flat strip / round wire armoured, extruded PVC type ST2 sheathed, heavy duty cable (to be laid on wall surface with necessary clamps / in existing cable trench / cable trays / conduit / pipe sleeves at road crossing or floor as per site requirement) conforming to IS:7098 (Part-1) & IEC:60502 (Part-1), of following sizes:

3.5 Core x 25 Sqmm

3.5 Core x 35 Sqmm

3.5 Core x 50 Sqmm

3.5 Core x 70 Sqmm

3.5 Core x 95 Sqmm

3.5 Core x 120 Sqmm

3.5 Core x 150 Sqmm

3.5 Core x 185 Sqmm

3.5 Core x 240 Sqmm

3.5 Core x 300 Sqmm

3.5 Core x 400 Sqmm

Supply, laying, testing & commissioning of 1.1 kV grade, XLPE insulated, stranded Copper conductor, galvanised steel flat strip / round wire armoured, extruded PVC type ST2 sheathed, heavy duty cable (to be laid on wall surface with necessary clamps / in existing cable trench / cable trays / conduit / pipe sleeves at road crossing or floor as per site requirement) conforming to IS:7098 (Part-1) & IEC:60502 (Part-1) of following sizes:

S.O.R. Mech 2019-20Page 86 of 166

Section- "E"


Rates inclusive of

GST




a Meter 60 6 66 18% 78

b Meter 108 6 114 18% 135

c Meter 151 6 157 18% 185

d Meter 231 6 237 18% 280

e Meter 333 6 339 18% 400

f Meter 549 6 555 18% 655

g Meter 757 12 769 18% 908

h Meter 1,036 12 1,048 18% 1,237

i Meter 1,483 12 1,495 18% 1,764

j Meter 2,133 12 2,145 18% 2,531

k Meter 2,685 18 2,703 18% 3,190

l Meter 3,350 18 3,368 18% 3,974

m Meter 4,120 18 4,138 18% 4,883

n Meter 5,311 24 5,335 18% 6,296

o Meter 6,617 24 6,641 18% 7,837

p Meter 8,682 24 8,706 18% 10,273

24

24.1

a Meter 315 30 345 18% 407

b Meter 356 30 386 18% 456

c Meter 423 30 453 18% 535

d Meter 500 36 536 18% 633

e Meter 577 36 613 18% 724

f Meter 644 36 680 18% 803

g Meter 749 36 785 18% 927

h Meter 899 36 935 18% 1,104

i Meter 1,046 36 1,082 18% 1,277

j Meter 1,314 36 1,350 18% 1,593

24.2

a Meter 319 30 349 18% 412

b Meter 646 36 682 18% 805

c Meter 751 36 787 18% 929

d Meter 830 36 866 18% 1,022

e Meter 928 36 964 18% 1,138

f Meter 1,092 36 1,128 18% 1,331

g Meter 1,256 36 1,292 18% 1,525

h Meter 1,476 36 1,512 18% 1,785

25

4 Core x 6.0 Sqmm

4 Core x 10 Sqmm

4 Core x 2.5 Sqmm

4 Core x 4.0 Sqmm

4 Core x 25 Sqmm

4 Core x 35 Sqmm

4 Core x 50 Sqmm

4 Core x 70 Sqmm

4 Core x 95 Sqmm

4 Core x 120 Sqmm

3 Core x 300 Sqmm

4 Core x 300 Sqmm

4 Core x 400 Sqmm

11 kV (Earthed / Unearthed) Grade Cable- Aluminium Conductor

Supply, laying, testing & commissioning of 6.35 / 11 kV (E) grade, XLPE insulated, stranded Aluminium conductor, galvanised steel flat strip / round wire armoured, extruded PVC type ST2 sheathed, heavy duty cable (to be laid on wall surface with necessary clamps / in existing cable trench / cable trays / conduit / pipe sleeves at road crossing or floor as per site requirement) conforming to IS:7098 (Part-2) & IEC:60502 (Part-2) of following sizes:

3 Core x 35 Sqmm

3 Core x 50 Sqmm

4 Core x 150 Sqmm

4 Core x 185 Sqmm

3 Core x 70 Sqmm

3 Core x 95 Sqmm

3 Core x 120 Sqmm

3 Core x 150 Sqmm

3 Core x 185 Sqmm

3 Core x 240 Sqmm

Supply, laying, testing & commissioning 11 / 11 kV (UE) grade, XLPE insulated, stranded Aluminium conductor, galvanised steel flat strip/ round wire armoured, extruded PVC type ST2 sheathed, heavy duty cable (to be laid on wall surface with necessary clamps / in existing cable trench / cable trays / conduit / pipe sleeves at road crossing or floor as per site requirement) conforming to IS:7098 (Part-2) & IEC:60502(Part-2), of following sizes:

3 Core x 70 Sqmm

3 Core x 95 Sqmm

3 Core x 120 Sqmm

3 Core x 150 Sqmm

3 Core x 185 Sqmm

3 Core x 240 Sqmm

3 Core x 300 Sqmm

4 Core x 16 Sqmm

4 Core x 240 Sqmm

3 Core x 400 Sqmm

3 Core x 400 Sqmm

6.6 kV (Earthed/ Unearthed) Grade Cable- Aluminium Conductor

S.O.R. Mech 2019-20Page 87 of 166

Section- "E"


Rates inclusive of

GST




25.1

a Meter 396 30 426 18% 503

b Meter 471 36 507 18% 599

c Meter 550 36 586 18% 692

d Meter 620 36 656 18% 775

e Meter 715 36 751 18% 887

f Meter 865 36 901 18% 1,064

g Meter 1,031 36 1,067 18% 1,259

h Meter 1,290 36 1,326 18% 1,565

25.2

a Meter 423 30 453 18% 535

b Meter 500 36 536 18% 633

c Meter 577 36 613 18% 724

d Meter 644 36 680 18% 803

e Meter 749 36 785 18% 927

f Meter 899 36 935 18% 1,104

g Meter 1,046 36 1,082 18% 1,277

h Meter 1,314 36 1,350 18% 1,593

26

26.1

a Meter 370 30 400 18% 472

b Meter 448 36 484 18% 572

c Meter 527 36 563 18% 665

d Meter 595 36 631 18% 745

e Meter 701 36 737 18% 870

f Meter 831 36 867 18% 1,023

g Meter 982 36 1,018 18% 1,202

h Meter 1,193 36 1,229 18% 1,451

27

27.1

a Each 1 - 1 18% 1.2

b Each 1 - 1 18% 1.18

c Each 1 - 1 18% 1.18

d Each 2 - 2 18% 2.36

e Each 2 - 2 18% 2.36

f Each 3 - 3 18% 3.54

g Each 4 - 4 18% 4.72

3 Core x 240 Sqmm

3 Core x 400 Sqmm

Supply, laying, testing & commissioning 6.6 / 6.6 kV (UE) grade, XLPE insulated, stranded Aluminium conductor, galvanised steel flat strip / round wire armoured, extruded PVC type ST2 sheathed, heavy duty cable (to be laid on wall surface with necessary clamps / in existing cable trench / cable trays / conduit / pipe sleeves at road crossing or floor as per site requirement) conforming to IS:7098 (Part-2) & IEC:60502(Part-2) of following sizes: *6.6kV (UE) = 11kV (E)

3 Core x 70 Sqmm

3 Core x 95 Sqmm

3 Core x 120 Sqmm

3 Core x 150 Sqmm

3 Core x 70 Sqmm

3 Core x 95 Sqmm

3 Core x 120 Sqmm

3 Core x 400 Sqmm

3.3 kV (Earthed/ Unearthed) Grade Cable- Aluminium Conductor

Supply, laying, testing & commissioning of 3.3 / 3.3 kV (UE) grade, XLPE insulated, stranded Aluminium conductor, galvanised steel flat strip / round wire armoured, extruded PVC type ST2 sheathed, heavy duty cable (to be laid on wall surface with necessary clamps / in existing cable trench / cable trays / conduit / pipe sleeves at road crossing or floor as per site requirement) conforming to IS:7098 (Part-2) & IEC:60502 (Part-2) of following sizes:* 3.3kV (E) = 3.3kV (UE)

3 Core x 70 Sqmm

3 Core x 95 Sqmm

3 Core x 120 Sqmm

3 Core x 185 Sqmm

3 Core x 240 Sqmm

3 Core x 300 Sqmm

3 Core x 300 Sqmm

3 Core x 400 Sqmm

Cable Terminals (Lugs)Providing & fitting crimping type Cable Terminals (Lugs) conforming to IS of following types and sizesAluminium Tubular Terminals (in Sq.mm.)

2.5

4

3 Core x 150 Sqmm

3 Core x 185 Sqmm

3 Core x 240 Sqmm

6

10

16

25

35

3 Core x 300 Sqmm

Supply, laying, testing & commissioning 3.8 / 6.6 kV (E) grade, XLPE insulated, stranded Aluminium conductor, galvanised steel flat strip / round wire armoured, extruded PVC type ST2 sheathed, heavy duty cable (to be laid on wall surface with necessary clamps / in existing cable trench / cable trays / conduit / pipe sleeves at road crossing or floor as per site requirement) conforming to IS:7098 (Part-2) & IEC:60502 (Part-2) of following sizes:

3 Core x 150 Sqmm

3 Core x 185 Sqmm

S.O.R. Mech 2019-20Page 88 of 166

Section- "E"


Rates inclusive of

GST




h Each 5 - 5 18% 5.90

i Each 8 - 8 18% 9.44

j Each 9 - 9 18% 10.62

k Each 13 - 13 18% 15.34

l Each 16 - 16 18% 18.88

m Each 21 - 21 18% 24.78

n Each 35 - 35 18% 41.30

o Each 49 - 49 18% 57.82

p Each 71 - 71 18% 83.78

q Each 103 - 103 18% 122

r Each 139 - 139 18% 164

27.2

a Each 2 - 2 18% 2.36

b Each 2 - 2 18% 2.36

c Each 2 - 2 18% 2.36

d Each 2 - 2 18% 2.36

e Each 3 - 3 18% 3.54

f Each 3 - 3 18% 3.54

g Each 4 - 4 18% 4.72

h Each 7 - 7 18% 8.26

i Each 10 - 10 18% 11.80

j Each 11 - 11 18% 12.98

k Each 16 - 16 18% 18.88

l Each 21 - 21 18% 24.78

m Each 25 - 25 18% 29.50

o Each 44 - 44 18% 51.92

p Each 64 - 64 18% 75.52

q Each 90 - 90 18% 106

r Each 129 - 129 18% 152

s Each 170 - 170 18% 201

27.3

a Each 3 - 3 18% 3.54

b Each 3 - 3 18% 3.54

c Each 3 - 3 18% 3.54

d Each 4 - 4 18% 4.72

e Each 6 - 6 18% 7.08

f Each 9 - 9 18% 10.62

g Each 12 - 12 18% 14.16

h Each 12 - 12 18% 14.16

i Each 21 - 21 18% 24.78

50

70

95

120

150

185

240

300

400

500

630

185

240

2.5

4

6

16

25

35

50

35

50

70

300

400

500

630

Aluminium Reducer Terminals (in Sq.mm.)

2.5

16

25

10

4

6

Aluminium Tubular Terminals(Long Barrel) (in Sq.mm.)

10

70

95

120

150

S.O.R. Mech 2019-20Page 89 of 166

Section- "E"


Rates inclusive of

GST




j Each 31 - 31 18% 36.58

k Each 41 - 41 18% 48.38

l Each 54 - 54 18% 63.72

m Each 69 - 69 18% 81.42

n Each 109 - 109 18% 129

o Each 139 - 139 18% 164

27.4

a Each 5 - 5 18% 5.90

b Each 7 - 7 18% 8.26

c Each 7 - 7 18% 8.26

d Each 10 - 10 18% 11.80

e Each 14 - 14 18% 16.52

f Each 21 - 21 18% 24.78

g Each 22 - 22 18% 25.96

h Each 33 - 33 18% 38.94

i Each 49 - 49 18% 57.82

j Each 73 - 73 18% 86.14

k Each 93 - 93 18% 110

l Each 125 - 125 18% 148

m Each 183 - 183 18% 216

o Each 249 - 249 18% 294

p Each 341 - 341 18% 402

q Each 481 - 481 18% 568

27.5

a Each 4 - 4 18% 4.72

b Each 6 - 6 18% 7.08

c Each 6 - 6 18% 7.08

d Each 8 - 8 18% 9.44

e Each 10 - 10 18% 11.80

f Each 15 - 15 18% 17.70

g Each 23 - 23 18% 27.14

h Each 38 - 38 18% 44.84

i Each 59 - 59 18% 69.62

j Each 88 - 88 18% 104

k Each 122 - 122 18% 144

l Each 151 - 151 18% 178

m Each 218 - 218 18% 257

o Each 306 - 306 18% 361

p Each 407 - 407 18% 480

q Each 637 - 637 18% 752

95

25

120

150

185

240

300

Copper Tubular Terminals (in Sq.mm.)

35

50

70

95

2.5

4

6

10

16

150

185

240

300

400

Copper Tubular Terminals (Long Barrel) (in Sq.mm.)

2.5

4

6

10

16

70

95

120

150

185

240

25

35

300

400

120

50

S.O.R. Mech 2019-20Page 90 of 166

Section- "E"


Rates inclusive of

GST




27.6

a Each 8 - 8 18% 9.44

b Each 8 - 8 18% 9.44

c Each 8 - 8 18% 9.44

d Each 10 - 10 18% 11.80

e Each 15 - 15 18% 17.70

f Each 24 - 24 18% 28.32

g Each 32 - 32 18% 37.76

h Each 35 - 35 18% 41.30

i Each 55 - 55 18% 64.90

j Each 80 - 80 18% 94.40

k Each 99 - 99 18% 117

l Each 137 - 137 18% 162

m Each 179 - 179 18% 211

o Each 284 - 284 18% 335

p Each 360 - 360 18% 425

q Each 813 - 813 18% 959

28

28.1

Sq mm Core mm Inch

a 2.5 2 to 4 19 `3/4 Each 19 - 19 18% 22.42

b 4 3 to 4 22 `7/8 Each 24 - 24 18% 28.32

c 6 3 to 4 22 `7/8 Each 24 - 24 18% 28.32

d 10 3 to 4 25 `1 Each 28 - 28 18% 33.04

e 16 3 to 4 28 `1 1/8 Each 41 - 41 18% 48.38

f 25 3 to 4 32 `1 1/4 Each 49 - 49 18% 57.82

g 35 3 to 3½ 32 `1 1/4 Each 49 - 49 18% 57.82

h 50 3 to 3½ 35 `1 3/8 Each 62 - 62 18% 73.16

i 70 3 to 3½ 38 `1 1/2 Each 77 - 77 18% 90.86

j 95 3 to 3½ 45 `1 3/4 Each 94 - 94 18% 111

k 120 3 to 3½ 45 `1 3/4 Each 94 - 94 18% 111

l 150 3 to 3½ 50 `2 Each 120 - 120 18% 142

m 185 3 to 3½ 57 `2 1/4 Each 154 - 154 18% 182

n 240 3 to 3½ 63 `2 1/2 Each 184 - 184 18% 217

o 300 3 to 3½ 70 `2 3/4 Each 219 - 219 18% 258

p 400 3 to 3½ 82 `3 1/4 Each 311 - 311 18% 367

q 630 3 to 3½ 100 `4 Each 449 - 449 18% 530

28.2

16

95

120

150

Copper Reducer Terminals (in Sq.mm.)

2.5

4

6

10

185

240

300

400

Cable Glands:

Providing & fitting heavy duty brass cable glands (nickel-plated) with washers & rubber ring conforming to IS, suitable for 3, 3½ & 4 core cables of following type & sizes:

35

50

70

Single Compression Brass Cable Glands

Suitable for cable Size of gland in

Double Compression Brass Cable Glands

25

S.O.R. Mech 2019-20Page 91 of 166

Section- "E"


Rates inclusive of

GST




Sq mm Core mm Inch

a 2.5 2 to 4 19 `3/4 Each 73 - 73 18% 86

b 4 3 to 4 22 `7/8 Each 107 - 107 18% 126

c 6 3 to 4 22 `7/8 Each 107 - 107 18% 126

d 10 3 to 4 25 `1 Each 120 - 120 18% 142

e 16 3 to 4 28 `1 1/8 Each 154 - 154 18% 182

f 25 3 to 4 32 `1 1/4 Each 203 - 203 18% 240

g 35 3 to 3½ 32 `1 1/4 Each 203 - 203 18% 240

h 50 3 to 3½ 35 `1 3/8 Each 240 - 240 18% 283

i 70 3 to 3½ 38 `1 1/2 Each 270 - 270 18% 319

j 95 3 to 3½ 45 `1 3/4 Each 392 - 392 18% 463

k 120 3 to 3½ 45 `1 3/4 Each 392 - 392 18% 463

l 150 3 to 3½ 50 `2 Each 448 - 448 18% 529

m 185 3 to 3½ 57 `2 1/4 Each 522 - 522 18% 616

n 240 3 to 3½ 63 `2 1/2 Each 720 - 720 18% 850

o 300 3 to 3½ 70 `2 3/4 Each 813 - 813 18% 959

p 400 3 to 3½ 82 `3 1/4 Each 1,157 - 1,157 18% 1,365

q 630 3 to 3½ 100 `4 Each 2,447 - 2,447 18% 2,887

29

29.1

a Each 527 325 852 18% 1,005

b Each 572 400 972 18% 1,147

c Each 595 450 1,045 18% 1,233

d Each 629 575 1,204 18% 1,421

e Each 833 675 1,508 18% 1,779

f Each 986 700 1,686 18% 1,989

29.2

a Each 624 325 949 18% 1,120

b Each 680 375 1,055 18% 1,245

c Each 901 450 1,351 18% 1,594

d Each 1,224 500 1,724 18% 2,034

e Each 1,870 600 2,470 18% 2,915

f Each 2,210 675 2,885 18% 3,404

29.3

a Each 761 400 1,161 18% 1,370

3C / 3.5C / 4C

25 to 50 3C /3.5C / 4C

70 to 150 3C/ 3.5C / 4C

Suitable for cable Size of gland in

Cable Terminations / Jointing Kits for 1.1kV grade PVC/ XLPE Cable

Providing & fitting heat shrink cable termination/ jointing kits for 1.1kV grade PVC/ XLPE insulated cable including necessary earth connectivity connection, material & consummables making the termination/ joint complete ensuring the joint resistance is within the permissble limit as per IS, of following types & sizes:

3C/ 3.5C / 4C

400 3C / 3.5C / 4C

500 to 630 3C / 3.5C / 4C

Straight Through Joints (Tubular Sleeve Version)

sq mm core

4 to 16

1.5 to 6 3C / 3.5C / 4C

10 to 16 3C /3.5C / 4C

25 to 50 3C/ 3.5C / 4C

3C/ 3.5C / 4C

185 to 300 3C / 3.5C / 4C

400 to 500 3C / 3.5C / 4C

Straight Through Joints (Cold Applied Insulations & Sealing System)

sq mm core

6 to 16 3C / 3.5C / 4C

185 to 300

70 to 150

Indoor / Outdoor End Termination Kit

S.O.R. Mech 2019-20Page 92 of 166

Section- "E"


Rates inclusive of

GST




b Each 900 500 1,400 18% 1,652

c Each 1,299 600 1,899 18% 2,241

d Each 1,760 700 2,460 18% 2,903

e Each 1,931 800 2,731 18% 3,223

f Each 2,319 900 3,219 18% 3,798

g Each 3,157 1,000 4,157 18% 4,905

30

30.1

a Each 2,416 325 2,741 18% 3,234

b Each 2,511 400 2,911 18% 3,435

c Each 3,353 450 3,803 18% 4,488

d Each 3,944 575 4,519 18% 5,332

e Each 4,164 675 4,839 18% 5,710

30.2

a Each 4,377 325 4,702 18% 5,548

b Each 4,445 400 4,845 18% 5,717

c Each 4,601 450 5,051 18% 5,960

d Each 5,258 575 5,833 18% 6,883

e Each 5,698 675 6,373 18% 7,520

30.3

a Each 4,404 325 4,729 18% 5,580

b Each 5,118 400 5,518 18% 6,511

c Each 8,046 450 8,496 18% 10,025

d Each 8,436 575 9,011 18% 10,633

e Each 8,983 675 9,658 18% 11,396

31

31.1

a Each 2,794 325 3,119 18% 3,680

b Each 3,431 400 3,831 18% 4,521

c Each 4,021 450 4,471 18% 5,276

d Each 4,223 575 4,798 18% 5,662

e Each 4,511 675 5,186 18% 6,119

31.2

a Each 4,243 675 4,918 18% 5,803

b Each 4,844 725 5,569 18% 6,571

c Each 5,198 850 6,048 18% 7,137

d Each 5,838 925 6,763 18% 7,980

3C/ 3.5C / 4C

300 3C / 3.5C / 4C

400 3C / 3.5C / 4C

Cable Terminations / Jointing Kits for 3.3 kV (E/UE) / 6.6 kV (E) XLPE Cable

25 to 50 3C /3.5C / 4C

Providing & fitting heat shrink cable termination/ jointing kits for 3.3 kV (E/UE) / 6.6 kV (E) grade XLPE insulated cable including necessary earth connectivity connection, material & consummables making the termination/ joint complete ensuring the joint resistance is within the permissble limit as per IS, of following types & sizes: Indoor Terminations Kit suitable for

16 to 35 3C

50 to 95 3C

120 to 185 3C

240 to 300 3C

400 3C

Outdoor Terminations Kit suitable for

16 to 35 3C

50 to 95 3C

120 to 185 3C

240 to 300 3C

400 3C

Straight Through Joints Kit suitable for

16 to 35 3C

50 to 95 3C

120 to 185 3C

240 to 300 3C

400 to 500 3C

Cable Terminations / Jointing Kits for 6.6 kV (UE) / 11 kV (E) grade XLPE Cable

Providing & fitting heat shrink cable termination/ jointing kits for 6.6 kV (UE) / 11 kV (E) grade XLPE insulated cable including necessary earth connectivity connection, material & consummables making the termination/ joint complete ensuring the joint resistance is within the permissble limit as per IS, of following types & sizes: Indoor Terminations Kit suitable for

16 to 35 3C

50 to 95 3C

120 to 185 3C

240 to 300 3C

400 3C


16 to 35 3C

50 to 95 3C

120 to 185 3C

240 to 300 3C

240 3C / 3.5C / 4C

70 to 95 3C/ 3.5C / 4C

120 to 185

S.O.R. Mech 2019-20Page 93 of 166

Section- "E"


Rates inclusive of

GST




e Each 6,141 1,000 7,141 18% 8,426

31.3

a Each 7,187 675 7,862 18% 9,277

b Each 8,044 725 8,769 18% 10,347

c Each 10,248 850 11,098 18% 13,096

d Each 11,195 925 12,120 18% 14,302

e Each 12,417 1,000 13,417 18% 15,832

32

32.1

a Each 3,264 675 3,939 18% 4,648

b Each 4,217 725 4,942 18% 5,832

c Each 5,394 850 6,244 18% 7,368

d Each 6,060 925 6,985 18% 8,242

e Each 6,384 1,000 7,384 18% 8,713

32.2

a Each 5,775 675 6,450 18% 7,611

b Each 6,934 725 7,659 18% 9,038

c Each 7,943 850 8,793 18% 10,376

d Each 10,562 925 11,487 18% 13,555

e Each 11,614 1,000 12,614 18% 14,885

32.3

a Each 13,605 675 14,280 18% 16,850

b Each 15,954 725 16,679 18% 19,681

c Each 16,857 850 17,707 18% 20,894

d Each 21,298 925 22,223 18% 26,223

e Each 24,465 1,000 25,465 18% 30,049

33

33.1

A

a No. 3,759 380 4,139 18% 4,884

b No. 4,223 427 4,650 18% 5,487

c No. 4,374 442 4,816 18% 5,683

d No. 4,775 482 5,257 18% 6,203

e No. 5,732 579 6,311 18% 7,447

f No. 7,334 741 8,075 18% 9,529

g No. 9,005 909 9,914 18% 11,699

h No. 13,905 1,404 15,309 18% 18,065

i No. 15,231 1,538 16,769 18% 19,787

j No. 25,485 2,574 28,059 18% 33,110

400 3C


16 to 35 3C

50 to 95 3C

120 to 185 3C

240 to 300 3C

400 to 500 3C

Cable Terminations / Jointing Kits for 11 kV (UE) grade XLPE Cable

Indoor Terminations Kit suitable for

25 to 50 3C

70 to 95 3C

120 to 185 3C

240 to 300 3C

400 to 500 3C


25 to 50 3C

120 to 185 3C

70 to 95 3C

120 to 185 3C

240 to 400 3C

500 to 630 3C


25 to 50 3C

70 to 95 3C

2.2

1.1

1.5

240 to 300 3C

400 to 500 3C

Supply, installation, testing & commissioning totally enclosed fan cooled squirrel cage induction motor, foot / flanged mounted enclosure having IP-55 degree of protection, continuously rated (S1) duty suitable for operation on 415 V ± 10%, 3 phase, 50Hz ± 5% AC supply with ambient temperature 500 C, Class F insulation (temperature rise limited to class B) conforming to high energy efficiency (IE-2) as per IS 12615:2011.

2 Pole / 3000 RPM, Horizontal Foot Mounted (All ratings in kW)

415V LV Induction Motor

5.5

7.5

9.3

0.37

0.55

0.75

3.7

S.O.R. Mech 2019-20Page 94 of 166

Section- "E"


Rates inclusive of

GST




k No. 27,905 2,818 30,723 18% 36,253

l No. 32,108 3,243 35,351 18% 41,714

m No. 41,610 4,203 45,813 18% 54,059

n No. 43,077 4,351 47,428 18% 55,965

o No. 64,734 6,538 71,272 18% 84,101

p No. 78,862 7,965 86,827 18% 102,456

q No. 101,255 10,227 111,482 18% 131,549

r No. 145,664 14,712 160,376 18% 189,244

s No. 188,589 19,048 207,637 18% 245,012

t No. 217,046 21,922 238,968 18% 281,982

u No. 271,314 27,403 298,717 18% 352,486

v No. 319,150 32,234 351,384 18% 414,633

w No. 330,854 33,416 364,270 18% 429,839

x No. 362,321 36,594 398,915 18% 470,720

y No. 362,321 36,594 398,915 18% 470,720

z No. 422,522 42,675 465,197 18% 548,932

aa No. 422,522 42,675 465,197 18% 548,932

ab No. 469,260 47,395 516,655 18% 609,653

ac No. 469,260 47,395 516,655 18% 609,653

ad No. 510,141 51,524 561,665 18% 662,765

ae No. 510,141 51,524 561,665 18% 662,765

B

a No. 3,871 391 4,262 18% 5,029

b No. 4,350 439 4,789 18% 5,651

c No. 4,505 455 4,960 18% 5,853

d No. 4,918 497 5,415 18% 6,390

e No. 5,903 596 6,499 18% 7,669

f No. 7,554 763 8,317 18% 9,814

g No. 9,275 937 10,212 18% 12,050

h No. 14,322 1,447 15,769 18% 18,607

i No. 15,688 1,584 17,272 18% 20,381

j No. 26,249 2,651 28,900 18% 34,102

k No. 28,741 2,903 31,644 18% 37,340

l No. 33,071 3,340 36,411 18% 42,965

m No. 42,858 4,329 47,187 18% 55,681

n No. 43,077 4,351 47,428 18% 55,965

o No. 67,932 6,861 74,793 18% 88,256

p No. 82,767 8,359 91,126 18% 107,529

q No. 106,279 10,734 117,013 18% 138,075

r No. 152,894 15,442 168,336 18% 198,636

11

15

150

18.5

22

30

37

45

55

75

90

110

125

132

9.3

1.1

1.5

275

160

180

200

225

250

0.37

0.75

0.55

315

2 Pole / 3000 RPM, Flange mounted (All ratings in kW)

30

11

15

18.5

37

45

55

2.2

3.7

5.5

7.5

22

S.O.R. Mech 2019-20Page 95 of 166

Section- "E"


Rates inclusive of

GST




s No. 197,579 19,955 217,534 18% 256,690

t No. 227,459 22,973 250,432 18% 295,510

u No. 284,439 28,728 313,167 18% 369,537

v No. 334,788 33,814 368,602 18% 434,950

w No. 346,957 35,043 382,000 18% 450,760

x No. 379,997 38,380 418,377 18% 493,685

y No. 379,997 38,380 418,377 18% 493,685

z No. 443,209 44,764 487,973 18% 575,808

aa No. 443,209 44,764 487,973 18% 575,808

ab No. 492,282 49,720 542,002 18% 639,562

ac No. 492,282 49,720 542,002 18% 639,562

ad No. 535,209 54,056 589,265 18% 695,333

ae No. 535,209 54,056 589,265 18% 695,333

C

a No. 3,973 401 4,374 18% 5,161

b No. 4,518 456 4,974 18% 5,869

c No. 4,594 464 5,058 18% 5,968

d No. 5,407 546 5,953 18% 7,025

e No. 5,906 597 6,503 18% 7,674

f No. 7,739 782 8,521 18% 10,055

g No. 9,898 1,000 10,898 18% 12,860

h No. 13,638 1,377 15,015 18% 17,718

i No. 15,883 1,604 17,487 18% 20,635

j No. 26,738 2,701 29,439 18% 34,738

k No. 26,738 2,701 29,439 18% 34,738

l No. 33,231 3,356 36,587 18% 43,173

m No. 43,103 4,353 47,456 18% 55,998

n No. 45,511 4,597 50,108 18% 59,127

o No. 62,796 6,342 69,138 18% 81,583

p No. 80,435 8,124 88,559 18% 104,500

q No. 94,897 9,585 104,482 18% 123,289

r No. 135,049 13,640 148,689 18% 175,453

s No. 171,939 17,366 189,305 18% 223,380

t No. 198,440 20,042 218,482 18% 257,809

u No. 238,965 24,135 263,100 18% 310,458

v No. 267,236 26,991 294,227 18% 347,188

w No. 279,885 28,268 308,153 18% 363,621

x No. 325,972 32,923 358,895 18% 423,496

y No. 325,972 32,923 358,895 18% 423,496

z No. 386,591 39,046 425,637 18% 502,252

75

90

110

125

132

1.1


0.37

0.55

0.75

1.5

150

160

180

200

225

250

275

315

3.7

5.5

7.5

9.3

2.2

11

15

18.5

22

30

37

45

55

75

90

110

125

132

150

160

180

S.O.R. Mech 2019-20Page 96 of 166

Section- "E"


Rates inclusive of

GST




aa No. 393,847 39,779 433,626 18% 511,679

ab No. 433,274 43,761 477,035 18% 562,901

ac No. 433,274 43,761 477,035 18% 562,901

ad No. 493,326 49,826 543,152 18% 640,919

ae No. 495,756 50,071 545,827 18% 644,076

af No. 622,995 62,923 685,918 18% 809,383

ag No. 870,422 87,913 958,335 18% 1,130,835

D

a No. 4,092 413 4,505 18% 5,316

b No. 4,654 470 5,124 18% 6,046

c No. 4,732 478 5,210 18% 6,148

d No. 5,569 562 6,131 18% 7,235

e No. 6,083 614 6,697 18% 7,902

f No. 7,971 805 8,776 18% 10,356

g No. 10,195 1,030 11,225 18% 13,246

h No. 14,047 1,419 15,466 18% 18,250

i No. 16,359 1,652 18,011 18% 21,253

j No. 27,582 2,786 30,368 18% 35,834

k No. 27,540 2,782 30,322 18% 35,780

l No. 34,228 3,457 37,685 18% 44,468

m No. 44,397 4,484 48,881 18% 57,680

n No. 46,876 4,734 51,610 18% 60,900

o No. 64,657 6,530 71,187 18% 84,001

p No. 82,820 8,365 91,185 18% 107,598

q No. 97,720 9,870 107,590 18% 126,956

r No. 139,069 14,046 153,115 18% 180,676

s No. 176,905 17,867 194,772 18% 229,831

t No. 204,202 20,624 224,826 18% 265,295

u No. 245,911 24,837 270,748 18% 319,483

v No. 275,060 27,781 302,841 18% 357,352

w No. 288,019 29,090 317,109 18% 374,189

x No. 335,487 33,884 369,371 18% 435,858

y No. 335,487 33,884 369,371 18% 435,858

z No. 405,399 40,945 446,344 18% 526,686

aa No. 405,399 40,945 446,344 18% 526,686

ab No. 446,008 45,047 491,055 18% 579,445

ac No. 446,008 45,047 491,055 18% 579,445

ad No. 510,365 51,547 561,912 18% 663,056

ae No. 510,365 51,547 561,912 18% 663,056

af No. 641,494 64,791 706,285 18% 833,416

200

225

250

275

315

355

375

4 Pole / 1500 RPM, Flanged Mounted (All ratings in kW)

0.37

0.75

0.55

1.5

2.2

1.1

3.7

5.5

7.5

9.3

11

15

18.5

22

30

37

160

180

200

225

45

55

75

90

110

125

250

275

315

355

132

150

S.O.R. Mech 2019-20Page 97 of 166

Section- "E"


Rates inclusive of

GST




ag No. 913,686 92,282 1,005,968 18% 1,187,042

E

a No. 4,793 484 5,277 18% 6,227

b No. 4,884 493 5,377 18% 6,345

c No. 5,686 574 6,260 18% 7,387

d No. 6,319 638 6,957 18% 8,209

e No. 7,982 806 8,788 18% 10,370

f No. 9,509 960 10,469 18% 12,353

g No. 14,890 1,504 16,394 18% 19,345

h No. 16,209 1,637 17,846 18% 21,058

i No. 26,255 2,652 28,907 18% 34,110

j No. 32,689 3,302 35,991 18% 42,469

k No. 32,658 3,299 35,957 18% 42,429

l No. 42,651 4,308 46,959 18% 55,412

m No. 55,531 5,609 61,140 18% 72,145

n No. 60,346 6,095 66,441 18% 78,400

o No. 94,816 9,576 104,392 18% 123,183

p No. 135,843 13,720 149,563 18% 176,484

q No. 162,466 16,409 178,875 18% 211,073

r No. 184,898 18,675 203,573 18% 240,216

s No. 229,169 23,146 252,315 18% 297,732

t No. 285,783 28,864 314,647 18% 371,283

u No. 317,698 32,087 349,785 18% 412,746

v No. 352,944 35,647 388,591 18% 458,537

w No. 370,152 37,385 407,537 18% 480,894

x No. 443,607 44,804 488,411 18% 576,325

y No. 383,560 38,740 422,300 18% 498,314

z No. 472,961 47,769 520,730 18% 614,461

aa No. 437,243 44,162 481,405 18% 568,058

ab No. 509,841 51,494 561,335 18% 662,375

ac No. 470,557 47,526 518,083 18% 611,338

ad No. 611,165 61,728 672,893 18% 794,014

ae No. 708,256 71,534 779,790 18% 920,152

F

a No. 4,937 499 5,436 18% 6,414

b No. 5,031 508 5,539 18% 6,536

c No. 5,856 591 6,447 18% 7,607

d No. 6,508 657 7,165 18% 8,455

e No. 8,221 830 9,051 18% 10,680

f No. 9,795 989 10,784 18% 12,725

1.5

2.2

1.5

375


3.7

5.5

7.5

9.3

11

15

18.5

22

30

37

45

55

75

90

110

125

132

150

160

180

200

225

250

275

315


0.37

0.75

0.55

1.1

2.2

0.37

0.55

0.75

1.1

S.O.R. Mech 2019-20Page 98 of 166

Section- "E"


Rates inclusive of

GST




g No. 15,336 1,549 16,885 18% 19,924

h No. 16,695 1,686 18,381 18% 21,690

i No. 27,043 2,731 29,774 18% 35,133

j No. 33,669 3,401 37,070 18% 43,743

k No. 33,638 3,397 37,035 18% 43,701

l No. 43,931 4,437 48,368 18% 57,074

m No. 57,197 5,777 62,974 18% 74,309

n No. 62,156 6,278 68,434 18% 80,752

o No. 97,637 9,861 107,498 18% 126,848

p No. 139,894 14,129 154,023 18% 181,747

q No. 167,317 16,899 184,216 18% 217,375

r No. 190,412 19,232 209,644 18% 247,380

s No. 235,852 23,821 259,673 18% 306,414

t No. 294,092 29,703 323,795 18% 382,078

u No. 326,964 33,023 359,987 18% 424,785

v No. 363,268 36,690 399,958 18% 471,950

w No. 380,992 38,480 419,472 18% 494,977

x No. 380,992 38,480 419,472 18% 494,977

y No. 394,803 39,875 434,678 18% 512,920

z No. 450,096 45,460 495,556 18% 584,756

aa No. 450,096 45,460 495,556 18% 584,756

ab No. 484,410 48,925 533,335 18% 629,335

ac No. 484,410 48,925 533,335 18% 629,335

ad No. 641,463 64,788 706,251 18% 833,376

ae No. 729,311 73,660 802,971 18% 947,506

33.2

A

a No. 4,324 437 4,761 18% 5,618

b No. 4,859 491 5,350 18% 6,313

c No. 5,032 508 5,540 18% 6,537

d No. 5,822 588 6,410 18% 7,564

e No. 6,590 666 7,256 18% 8,562

f No. 8,433 852 9,285 18% 10,956

g No. 10,588 1,069 11,657 18% 13,755

h No. 15,993 1,615 17,608 18% 20,777

i No. 17,515 1,769 19,284 18% 22,755

j No. 29,470 2,976 32,446 18% 38,286

k No. 32,092 3,241 35,333 18% 41,693

l No. 36,929 3,730 40,659 18% 47,978

3.7

5.5

7.5

9.3

11

15

18.5

22

1.5

0.37

0.55

0.75

30

37

45

55

75

90

250

275

315

Supply, installation, testing & commissioning totally enclosed fan cooled squirrel cage induction motor, foot / flanged mounted enclosure having IP-55 degree of protection, continuously rated (S1) duty suitable for operation on 415 V ± 10%, 3 phase, 50Hz ± 5% AC supply with ambient temperature 50 deg. C, Class F insulation (temperature rise limited to class B) conforming to premium efficiency (IE-3) as per IS 12615:2011 and IS / IEC 60034-1:2017.


110

125

132

150

3.7

5.5

7.5

9.3

11

15

1.1

2.2

160

180

200

225

S.O.R. Mech 2019-20Page 99 of 166

Section- "E"


Rates inclusive of

GST




m No. 47,850 4,833 52,683 18% 62,166

n No. 49,538 5,003 54,541 18% 64,358

o No. 74,327 7,507 81,834 18% 96,564

p No. 90,129 9,103 99,232 18% 117,094

q No. 116,328 11,749 128,077 18% 151,131

r No. 170,535 17,224 187,759 18% 221,556

s No. 217,196 21,937 239,133 18% 282,177

t No. 250,643 25,315 275,958 18% 325,630

u No. 314,239 31,738 345,977 18% 408,253

v No. 366,063 36,972 403,035 18% 475,581

w No. 384,125 38,797 422,922 18% 499,048

x No. 421,017 42,523 463,540 18% 546,977

y No. 488,145 49,303 537,448 18% 634,189

z No. 491,606 49,652 541,258 18% 638,684

aa No. 546,567 55,203 601,770 18% 710,089

ab No. 546,567 55,203 601,770 18% 710,089

ac No. 594,180 60,012 654,192 18% 771,947

ad No. 594,180 60,012 654,192 18% 771,947

B

a No. 4,453 450 4,903 18% 5,786

b No. 5,005 505 5,510 18% 6,502

c No. 5,183 523 5,706 18% 6,733

d No. 5,996 606 6,602 18% 7,790

e No. 6,788 686 7,474 18% 8,819

f No. 8,686 877 9,563 18% 11,284

g No. 10,905 1,101 12,006 18% 14,167

h No. 16,472 1,664 18,136 18% 21,400

i No. 18,041 1,822 19,863 18% 23,438

j No. 30,354 3,066 33,420 18% 39,436

k No. 33,054 3,338 36,392 18% 42,943

l No. 38,036 3,842 41,878 18% 49,416

m No. 49,286 4,978 54,264 18% 64,032

n No. 52,016 5,254 57,270 18% 67,579

o No. 78,004 7,878 85,882 18% 101,341

p No. 94,589 9,553 104,142 18% 122,888

q No. 122,104 12,333 134,437 18% 158,636

r No. 179,016 18,081 197,097 18% 232,574

s No. 227,736 23,001 250,737 18% 295,870

t No. 262,856 26,548 289,404 18% 341,497

u No. 329,632 33,293 362,925 18% 428,252

18.5

22

30

37

45

55

75

90

110

125

132

160

180

200

225

250

275

315

2 Pole / 3000 RPM, Flange mounted (All ratings in kW)

30

0.37

0.55

0.75

1.1

1.5

7.5

5.5

2.2

3.7

9.3

11

15

18.5

22

37

45

55

75

90

110

S.O.R. Mech 2019-20Page 100 of 166

Section- "E"


Rates inclusive of

GST




v No. 384,047 38,789 422,836 18% 498,946

w No. 403,012 40,704 443,716 18% 523,585

x No. 441,748 44,617 486,365 18% 573,911

y No. 512,293 51,742 564,035 18% 665,561

z No. 515,867 52,103 567,970 18% 670,205

aa No. 573,576 57,931 631,507 18% 745,178

ab No. 573,576 57,931 631,507 18% 745,178

ac No. 623,569 62,981 686,550 18% 810,129

ad No. 623,569 62,981 686,550 18% 810,129

C

a No. 4,172 421 4,593 18% 5,420

b No. 5,201 525 5,726 18% 6,757

c No. 5,283 534 5,817 18% 6,864

d No. 6,217 628 6,845 18% 8,077

e No. 6,793 686 7,479 18% 8,825

f No. 8,901 899 9,800 18% 11,564

g No. 11,381 1,149 12,530 18% 14,785

h No. 15,686 1,584 17,270 18% 20,379

i No. 18,263 1,845 20,108 18% 23,727

j No. 28,217 2,850 31,067 18% 36,659

k No. 32,087 3,241 35,328 18% 41,687

l No. 39,879 4,028 43,907 18% 51,810

m No. 51,726 5,224 56,950 18% 67,201

n No. 52,337 5,286 57,623 18% 67,995

o No. 71,435 7,215 78,650 18% 92,807

p No. 92,360 9,328 101,688 18% 119,992

q No. 109,016 11,011 120,027 18% 141,632

r No. 158,137 15,972 174,109 18% 205,449

s No. 198,602 20,059 218,661 18% 258,020

t No. 229,373 23,167 252,540 18% 297,997

u No. 276,423 27,919 304,342 18% 359,124

v No. 309,245 31,234 340,479 18% 401,765

w No. 324,321 32,756 357,077 18% 421,351

x No. 378,328 38,211 416,539 18% 491,516

y No. 443,800 44,824 488,624 18% 576,576

z No. 458,158 46,274 504,432 18% 595,230

aa No. 504,093 50,913 555,006 18% 654,907

ab No. 504,093 50,913 555,006 18% 654,907

ac No. 577,679 58,346 636,025 18% 750,510

ad No. 577,679 58,346 636,025 18% 750,510

0.55

275

315


0.37

200

225

250

11

15

18.5

0.75

125

132

160

180

1.5

2.2

3.7

5.5

7.5

9.3

22

30

37

55

75

90

45

110

125

200

132

160

180

225

250

315

275

1.1

S.O.R. Mech 2019-20Page 101 of 166

Section- "E"


Rates inclusive of

GST




D

a No. 4,708 476 5,184 18% 6,117

b No. 5,357 541 5,898 18% 6,960

c No. 5,442 550 5,992 18% 7,071

d No. 6,404 647 7,051 18% 8,320

e No. 6,996 707 7,703 18% 9,090

f No. 9,168 926 10,094 18% 11,911

g No. 11,722 1,184 12,906 18% 15,229

h No. 16,156 1,632 17,788 18% 20,990

i No. 18,811 1,900 20,711 18% 24,439

j No. 29,064 2,935 31,999 18% 37,759

k No. 33,049 3,338 36,387 18% 42,937

l No. 41,076 4,149 45,225 18% 53,366

m No. 53,278 5,381 58,659 18% 69,218

n No. 53,907 5,445 59,352 18% 70,035

o No. 73,555 7,429 80,984 18% 95,561

p No. 95,102 9,605 104,707 18% 123,554

q No. 112,264 11,339 123,603 18% 145,852

r No. 162,852 16,448 179,300 18% 211,574

s No. 204,368 20,641 225,009 18% 265,511

t No. 236,062 23,842 259,904 18% 306,687

u No. 284,524 28,737 313,261 18% 369,648

v No. 318,331 32,151 350,482 18% 413,569

w No. 333,859 33,720 367,579 18% 433,743

x No. 389,487 39,338 428,825 18% 506,014

y No. 465,725 47,038 512,763 18% 605,060

z No. 471,711 47,643 519,354 18% 612,838

aa No. 519,024 52,421 571,445 18% 674,305

ab No. 519,024 52,421 571,445 18% 674,305

ac No. 594,610 60,056 654,666 18% 772,506

ad No. 594,818 60,077 654,895 18% 772,776

E

a No. 5,512 557 6,069 18% 7,161

b No. 5,618 567 6,185 18% 7,298

c No. 6,540 660 7,200 18% 8,496

d No. 7,370 744 8,114 18% 9,575

e No. 9,181 927 10,108 18% 11,927

f No. 10,936 1,105 12,041 18% 14,208

g No. 17,130 1,730 18,860 18% 22,255

h No. 18,640 1,883 20,523 18% 24,217


0.37

0.55

0.75

3.7

1.1

1.5

5.5

7.5

9.3

11

15

18.5

2.2

0.75

1.1

1.5

22

30

37

45

55

75

0.55

90

110

125

132

160

3.7

180

200

225

250

275

315


0.37

2.2

5.5

S.O.R. Mech 2019-20Page 102 of 166

Section- "E"


Rates inclusive of

GST




i No. 31,507 3,182 34,689 18% 40,933

j No. 35,456 3,581 39,037 18% 46,064

k No. 37,558 3,793 41,351 18% 48,794

l No. 49,050 4,954 54,004 18% 63,725

m No. 63,859 6,450 70,309 18% 82,965

n No. 69,398 7,009 76,407 18% 90,160

o No. 108,923 11,001 119,924 18% 141,510

p No. 159,255 16,085 175,340 18% 206,901

q No. 190,473 19,238 209,711 18% 247,459

r No. 216,562 21,873 238,435 18% 281,353

s No. 265,051 26,770 291,821 18% 344,349

t No. 331,278 33,459 364,737 18% 430,390

u No. 368,740 37,243 405,983 18% 479,060

v No. 409,905 41,400 451,305 18% 532,540

w No. 429,972 43,427 473,399 18% 558,611

x No. 445,671 45,013 490,684 18% 579,007

y No. 509,000 51,409 560,409 18% 661,283

z No. 509,000 51,409 560,409 18% 661,283

aa No. 547,710 55,319 603,029 18% 711,574

ab No. 547,710 55,319 603,029 18% 711,574

ac No. 702,057 70,908 772,965 18% 912,099

ad No. 829,208 83,750 912,958 18% 1,077,290

F

a No. 5,677 573 6,250 18% 7,375

b No. 5,786 584 6,370 18% 7,517

c No. 6,736 680 7,416 18% 8,751

d No. 7,590 767 8,357 18% 9,861

e No. 9,456 955 10,411 18% 12,285

f No. 11,264 1,138 12,402 18% 14,634

g No. 17,644 1,782 19,426 18% 22,923

h No. 19,199 1,939 21,138 18% 24,943

i No. 32,451 3,278 35,729 18% 42,160

j No. 36,520 3,688 40,208 18% 47,445

k No. 38,684 3,907 42,591 18% 50,257

l No. 50,521 5,103 55,624 18% 65,636

m No. 65,774 6,643 72,417 18% 85,452

n No. 71,481 7,220 78,701 18% 92,867

o No. 112,167 11,329 123,496 18% 145,725

p No. 164,005 16,564 180,569 18% 213,071

q No. 196,159 19,812 215,971 18% 254,846

22

37

45

55

75

90

7.5

9.3

11

15

18.5

0.55

0.75

110

125

132

160

180

200

30

1.5

2.2

3.7

5.5

7.5

9.3

11

15

18.5

22

30

37

45

1.1

225

250

275

315


0.37

S.O.R. Mech 2019-20Page 103 of 166

Section- "E"


Rates inclusive of

GST




r No. 223,031 22,526 245,557 18% 289,757

s No. 272,810 27,554 300,364 18% 354,430

t No. 341,025 34,443 375,468 18% 443,052

u No. 379,611 38,341 417,952 18% 493,183

v No. 422,011 42,623 464,634 18% 548,268

w No. 442,679 44,711 487,390 18% 575,120

x No. 458,850 46,344 505,194 18% 596,129

y No. 524,078 52,932 577,010 18% 680,872

z No. 524,078 52,932 577,010 18% 680,872

aa No. 563,950 56,959 620,909 18% 732,673

ab No. 563,950 56,959 620,909 18% 732,673

ac No. 736,902 74,427 811,329 18% 957,368

ad No. 853,893 86,243 940,136 18% 1,109,360

34

34.1

kVAR 259 26 285 18% 336

35

35.1

a Rmt. 231 23 254 18% 300

b Rmt. 267 27 294 18% 347

c Rmt. 303 31 334 18% 394

d Rmt. 340 34 374 18% 441

e Rmt. 375 38 413 18% 487

f Rmt. 277 28 305 18% 360

g Rmt. 313 32 345 18% 407

h Rmt. 349 35 384 18% 453

i Rmt. 385 39 424 18% 500

j Rmt. 421 43 464 18% 548

35.2

a Rmt. 154 16 170 18% 201

b Rmt. 200 20 220 18% 260

c Rmt. 337 34 371 18% 438

d Rmt. 473 48 521 18% 615

e Rmt. 611 62 673 18% 794

f Rmt. 182 18 200 18% 236

g Rmt. 228 23 251 18% 296

h Rmt. 365 37 402 18% 474

i Rmt. 502 51 553 18% 653

200

225

250

55

75

90

110

125

275

315

LT Power Capacitor

Supply & erecting heavy duty APP type capacitor unit, vacuum impregnated with non-PCB / non toxic oil, internally delta connected with built in internal fuses complete with discharge resistances & terminal cover, rated for 440 V AC, 3 Phase, 50Hz as per IS - 13585 Part-1.

APP type Capacitor

Cable Trays & Accessories

132

160

180

Supply & laying MS ladder type cable trays with side channels of size - 75 x 15 x 15 mm / 100 x 15 x 15 mm & rungs of size - 35 x 15 x 15 mm spaced at 250 mm apart, fabricated from 2 mm thick sheet steel in standard length of 2.5 meter, duly finished with one coat of red oxide & two coats of aluminium paint as per IS including accessories such as coupler plates / fish plates, bends, tees, reducers, elbows, covers and electro-galvanized hardware etc, erected on existing support as per specification and instruction of engineer in charge.

150(W) x 75(H) x 2.0 mm Thick

300(W) x 75(H) x 2.0 mm Thick

450(W) x 75(H) x 2.0 mm Thick

600(W) x 75(H) x 2.0 mm Thick

750(W) X 75(H) x 2.0 mm Thick

600(W) x 100(H) x 2.0 mm Thick

750(W) X 100(H) x 2.0 mm Thick

Supply & laying MS perforated type cable trays with returned edge/ flange, fabricated from 2.0 mm thk sheet steel in the standard length of 2.5 mtrs, duly finished with one coat of red oxide & two coats of aluminium paint as per IS including accessories such as coupler plates / fish plates, bends, tees, reducers, elbows, covers and electro-galvanized hardware etc, erected on existing support as per specification and instruction of engineer in charge.

100(W) x 35(H) x 2.0 mm Thick

150(W) x 35(H) x 2.0 mm Thick

300(W) x 35(H) x 2.0 mm Thick

150(W) x 100(H) x 2.0 mm Thick

300(W) x 100(H) x 2.0 mm Thick

450(W) x 100(H) x 2.0 mm Thick

150(W) x 50(H) x 2.0 mm Thick

300(W) x 50(H) x 2.0 mm Thick

450(W) x 50(H) x 2.0 mm Thick

450(W) x 35(H) x 2.0 mm Thick

600(W) x 35(H) x 2.0 mm Thick

100(W) x 50(H) x 2.0 mm Thick

S.O.R. Mech 2019-20Page 104 of 166

Section- "E"


Rates inclusive of

GST




j Rmt. 636 64 700 18% 826

C

a Rmt. 305 31 336 18% 396

b Rmt. 352 36 388 18% 458

c Rmt. 399 40 439 18% 518

d Rmt. 450 45 495 18% 584

e Rmt. 496 50 546 18% 644

f Rmt. 365 37 402 18% 474

g Rmt. 414 42 456 18% 538

h Rmt. 460 46 506 18% 597

i Rmt. 507 51 558 18% 658

j Rmt. 559 56 615 18% 726

D

a Rmt. 207 21 228 18% 269

b Rmt. 269 27 296 18% 349

c Rmt. 451 46 497 18% 586

d Rmt. 633 64 697 18% 822

e Rmt. 818 83 901 18% 1,063

f Rmt. 248 25 273 18% 322

g Rmt. 305 31 336 18% 396

h Rmt. 491 50 541 18% 638

i Rmt. 673 68 741 18% 874

j Rmt. 859 87 946 18% 1,116

E

a Rmt. 450 45 495 18% 584

b Rmt. 601 61 662 18% 781

c Rmt. 660 67 727 18% 858

d Rmt. 719 73 792 18% 935

e Rmt. 779 79 858 18% 1,012

F

a Rmt. 147 15 162 18% 191

b Rmt. 273 28 301 18% 355

c Rmt. 301 30 331 18% 391

600(W) x 50(H) x 2.0 mm Thick

Supply & laying GI ladder type cable trays with side channels of size - 75 x 15 x 15 mm/ 100 x 15 x 15 mm & rungs of size - 35 x15 x 15 mm spaced at 250 mm apart, fabricated from 2 mm thick sheet steel in standard length of 2.5 meter, duly hot dipped galvanized after fabrication as per IS 2629-1989/ IS 4759-1984 including accessories such as coupler plates/ fish plates, bends, tees, reducers, elbows, covers and electro-galvanized hardware etc, erected on existing support as per specification and instruction of engineer in charge.

150(W) x 75(H) x 2.0 mm Thick

100(W) x 50(H) x 2.0 mm Thick

150(W) x 50(H) x 2.0 mm Thick

300(W) x 75(H) x 2.0 mm Thick

450(W) x 75(H) x 2.0 mm Thick

600(W) x 75(H) x 2.0 mm Thick

750(W) X 75(H) x 2.0 mm Thick

150(W) x 100(H) x 2.0 mm Thick

300(W) x 100(H) x 2.0 mm Thick

450(W) x 100(H) x 2.0 mm Thick

600(W) x 100(H) x 2.0 mm Thick

450(W) x 100(H) x 4 mm Thick

600(W) x 100(H) x 4 mm Thick

Supply & laying GI perforated type cable trays with returned edge/ flange, fabricated from 2.0 mm thk sheet steel in the standard length of 2.5 mtrs, duly hot dipped galvanized after fabrication as per IS 2629-1989 / IS 4759-1984 including accessories such as coupler plates/ fish plates, bends, tees, reducers, elbows, covers and electro-galvanized hardware etc, erected on existing support as per specification and instruction of engineer in charge.

100(W) x 35(H) x 2.0 mm Thick

150(W) x 35(H) x 2.0 mm Thick

300(W) x 35(H) x 2.0 mm Thick

450(W) x 35(H) x 2.0 mm Thick

600(W) x 35(H) x 2.0 mm Thick

Supply & laying FRP perforated type cable trays manufactured as per NEMA FGI-1993 / IS 6746 - 1994/ ASTM-D standards using corrosion resistant polyester flame retardant U.V stabilised resin & various types of glass fibres with glass content ≥ 55% with minimum thickness of 3.0 mm for all sizes upto 150 mm (W) & 4.0 mm thickness for all sizes of 300 mm & above, supplied in standard length of 3 mtr including accessories such as coupler plates/ fish plates, bends, tees, reducers, elbows, covers and electro-galvanized / SS-304 hardware etc, erected on existing support as per specification and instruction of engineer in charge.

100(W) x 30(H) x 3mm thick

150(W) x 50(H) x 3 mm Thick

300(W) x 50(H) x 4 mm Thick.

450(W) x 50(H) x 2.0 mm Thick

600(W) x 50(H) x 2.0 mm Thick

Supply & laying FRP ladder type cable trays with C shaped side channels of size - 75 x 25 x 25 mm for 150 mm wide and 100 x 75 x 75 mm for 300 mm wide & above, rungs of 25 mm square hollow tube spaced at 300 mm apart, manufactured as per NEMA FGI-1993 / IS 6746 - 1994/ ASTM-D standards using corrosion resistant polyester flame retardant U.V stabilised resin & various types of glass fibres with glass content ≥ 55% with minimum thickness of 3.0 mm for all sizes upto 150 mm (W) & 4.0 mm thickness for all sizes of 300 mm & above, supplied in standard length of 3 mtr including accessories such as coupler plates/ fish plates, bends, tees, reducers, elbows, covers and electro-galvanized / SS-304 hardware etc, erected on existing support as per specification and instruction of engineer in charge.


300(W) x 100(H) x 4 mm Thick

750(W) X 100(H) x 2.0 mm Thick

750(W) x 100(H) x 4 mm Thick

300(W) x 50(H) x 2.0 mm Thick

S.O.R. Mech 2019-20Page 105 of 166

Section- "E"


Rates inclusive of

GST




d Rmt. 909 92 1,001 18% 1,181

e Rmt. 1,232 124 1,356 18% 1,600

36

A

1 KW 20,000 2,000 22,000 Incl. 22,000

2 KW 18,000 1,750 19,750 Incl. 19,750

3 KW 22,000 2,250 24,250 Incl. 24,250

4 KW 22,000 2,500 24,500 Incl. 24,500

B

1 KW 20,000 2,000 22,000 Incl. 22,000

2 KW 24,000 2,250 26,250 Incl. 26,250

3 KW 24,000 2,500 26,500 Incl. 26,500

C

1 KW 24,000 2,000 26,000 Incl. 26,000 2 KW 26,000 2,500 28,500 Incl. 28,500 3 KW 27,500 2,750 30,250 Incl. 30,250 D

1 KW 20,000 2,000 22,000 Incl. 26,000

2 KW 24,000 3,000 27,000 Incl. 28,500

3 KW 24,000 3,000 27,000 Incl. 30,250

E

1 KW 24,000 2,000 26,000 Incl. 26,000

2 KW 26,000 3,000 29,000 Incl. 28,500


Rate per KW for comprehensive work of S.I.T.C. of Electro-mechanical components for headworks of R.W.S.S.(This is only for the purpose of rough estimation)Electro mechanical components of Pumping Station having installed capacity up to ≤ 75 kW with working load not exceding 75 KW

Supply, installation, testing & commissioning of electro-mechanical equipments of water supply pumping system viz. pumping machinery (of following type & rating), valves (SV/BFV/DPCV), Suction-delivery-discharge header pipes & specials, expansion bellows, flow meter (full bore electromagnetic - For size ≤ 1400 mm) / ultrasonic - For size ≥ 1500 mm), material handling system (motorised chain pulley block with geared travelling trolley), vaccum pumps with accessories or horizontal mono submersible (drain) pump with accessories including LV MCC - APFC panels, LT XLPE insulated Cu / Al armoured / PVC insulated round Copper submersible cables with tray & kits, earthing system, fire extinguisher, Exhaust Fan, safety accessories etc. as per specifications.

Horizontal split casing

End suction (Back Pull Out)

Volute type submerged centrifugal

Vertical TurbineElectro mechanical components of water supply system of different type of pumps ranging from > 75 kW but ≤ 200 kW

Vertical Turbine

Electro mechanical components of Water Supply Pumping Station having installed capacity ranging from>75 kW to ≤ 200 KW with working load exceding 75 KW but below 320 KW.Supply, installation, testing & commissioning of electrical & mechanical equipments of water supply pumping system viz. pumping machinery (of following type & rating), valves (SV/BFV/DPCV), Suction-delivery-discharge header pipes & specials, expansion bellows, flow meter (full bore electromagnetic - For size ≤ 1400 mm) / ultrasonic - For size ≥ 1500 mm)electromagnetic - For size ≤ 1400 mm) / ultrasonic - For size ≥ 1500 mm), material handling system (EOT), vaccum pump with accessories or horizontal mono submersible (drain) pump with accessories including 11 kV switchyard with dristribution transformer, LV MCC - APFC panels, HT / LT XLPE insulated Cu / Al armoured / PVC insulated round Copper submersible cables with tray & kits, earthing system, fire extinguisher, exhaust fan safety accessories etc. as per specifications.



Vertical Turbine

Supply, installation, testing & commissioning of electrical & mechanical equipments of water supply pumping system viz. pumping machinery (of following type & rating), valves (SV/BFV/DPCV), Suction-delivery-discharge header pipes & specials, expansion bellows, flow meter (full bore electromagnetic - For size ≤ 1400 mm) / ultrasonic - For size ≥ 1500 mm), material handling system (EOT), horizontal mono submersible (drain) pump with accessories, fire extinguisher, exhaust fan including 11 kV switchyard with dristribution transformer, HT switchgear panel, LV MCC - APFC panels, HT / LT XLPE insulated Cu / Al armoured / PVC insulated round Copper submersible cables with tray & kits, earthing system, safety accessories with PLC based instrumentation with control system as per specifications.



Vertical Turbine




Electro mechanical components of water supply system of different type of pumps ranging from > 200 kW but ≤ 450 kW

Supply, installation, testing & commissioning of electrical & mechanical equipments of water supply pumping system viz. pumping machinery (of following type & rating), valves (SV/BFV/DPCV), Suction-delivery-discharge header pipes & specials, expansion bellows, flow meter (full bore electromagnetic - For size ≤ 1400 mm) / ultrasonic - For size ≥ 1500 mm), material handling system (EOT), horizontal mono submersible (drain) pump with accessories, fire extinguisher, exhaust fan including 11 kV switchyard with dristribution transformer, HT switchgear panel, LV MCC - APFC panels, HT / LT XLPE insulated Cu / Al armoured / PVC insulated round Copper submersible cables with tray & kits, earthing system, safety accessories with PLC based instrumentation with control system as per specifications.

Electro mechanical components of Water Supply Pumping Station having installed capacity > 200 KW with working load exceding 320 KW.

Supply, installation, testing & commissioning of electrical & mechanical equipments of water supply pumping system viz. pumping machinery (of following type & rating), valves (SV/BFV/DPCV), Suction-delivery-discharge header pipes & specials, expansion bellows, flow meter (full bore electromagnetic - For size ≤ 1400 mm) / ultrasonic - For size ≥ 1500 mm), material handling system (EOT), vaccum pumps with accessories or horizontal mono submersible (drain) pump with accessories, fire extinguisher, exhaust fan including 11 kV switchyard with dristribution transformer, HT switchgear panel, LV MCC - APFC panels, HT / LT XLPE insulated Cu / Al armoured / PVC insulated round Copper submersible cables with tray & kits, earthing system, safety accessories etc. as per specifications.

Horizontal split casingVolute type submerged centrifugal

S.O.R. Mech 2019-20Page 106 of 166

Section- "E"


Rates inclusive of

GST




3 KW 27,500 3,000 30,500 Incl. 30,250

Note:-

37

37.1

Capacity Span Long travel

Lift

Tonne m m m

1.1 1 T 0 m - 6 m

12 m 6 m - 10 m

set 135,000 25,000 160,000 18% 188,800

1.2 1 T 6 m - 9 m

12 m 6 m - 10 m

set 140,000 25,000 165,000 18% 194,700

1.3 1 T 9 m - 12 m

12 m 6 m - 10 m

set 145,000 25,000 170,000 18% 200,600

2.1 2 T 0 m - 6 m

12 m 6 m - 10 m

set 155,000 25,000 180,000 18% 212,400

2.2 2 T 6 m - 9 m

12 m 6 m - 10 m

set 162,500 25,000 187,500 18% 221,250

2.3 2 T 9 m - 12 m

12 m 6 m - 10 m

set 165,000 25,000 190,000 18% 224,200

3.1 3 T 0 m - 6 m

12 m 6 m - 10 m

set 215,000 25,000 240,000 18% 283,200

3.2 3 T 6 m - 9 m

12 m 6 m - 10 m

set 225,000 25,000 250,000 18% 295,000

3.3 3 T 9 m - 12 m

12 m 6 m - 10 m

set 230,000 25,000 255,000 18% 300,900

37.2

Sr No Capacity Span Long travel

Lift

Tonne m m m

1.1 1 T 0 m - 6 m

12 m 6 m - 10 m

set 285,000 25,000 310,000 18% 365,800

1.2 1 T 6 m - 9 m

12 m 6 m - 10 m

set 335,000 25,000 360,000 18% 424,800

1.3 1 T 9 m - 12 m

12 m 6 m - 10 m

set 345,000 25,000 370,000 18% 436,600

2.1 2 T 0 m - 6 m

12 m 6 m - 10 m

set 325,000 25,000 350,000 18% 413,000

2.2 2 T 6 m - 9 m

12 m 6 m - 10 m

set 375,000 25,000 400,000 18% 472,000

2.3 2 T 9 m - 12 m

12 m 6 m - 10 m

set 400,000 25,000 425,000 18% 501,500

3.1 3 T 0 m - 6 m

12 m 6 m - 10 m

set 406,000 25,000 431,000 18% 508,580

3.2 3 T 6 m - 9 m

12 m 6 m - 10 m

set 420,000 25,000 445,000 18% 525,100

3.3 3 T 9 m - 12 m

12 m 6 m - 10 m

set 440,000 25,000 465,000 18% 548,700

4.1 5 T 0 m - 6 m

12 m 6 m - 10 m

set 420,000 25,000 445,000 18% 525,100

4.2 5 T 6 m - 9 m

12 m 6 m - 10 m

set 485,000 25,000 510,000 18% 601,800

4.3 5 T 9 m - 12 m

12 m 6 m - 10 m

set 500,000 25,000 525,000 18% 619,500

5.1 6 T 0 m - 6 m

12 m 6 m - 10 m

set 435,000 25,000 460,000 18% 542,800

5.2 6 T 6 m - 9 m

12 m 6 m - 10 m

set 500,000 25,000 525,000 18% 619,500

5.3 6 T 9 m - 12 m

12 m 6 m - 10 m

set 625,000 25,000 650,000 18% 767,000

6.1 7.5 T 0 m - 6 m

12 m 6 m - 10 m

set 525,000 25,000 550,000 18% 649,000

6.2 7.5 T 6 m - 9 m

12 m 6 m - 10 m

set 585,000 25,000 610,000 18% 719,800

Single Girder H.O.T. Crane

Providing & erecting Single girder type H.O.T. crane with geared travelling trolly with seven mtr lift complete with manually operated chain pulley block, long travel rail track (40 mm sq. bar), moving or cross girder, brake, safety device, etc. & tested to 50% overload

Single Girder E.O.T. Crane

Providing & erecting Single girder type fully electrically operated E.O.T. crane with electrically operated hoist, class II duty, geared travelling trolley with seven meter lift complete with long travel rail track (40 mm sq. bar), moving or cross girder, all three motions electrically operated by suitable rating motor IP 54, control panel & down pendant control block, brake, safety device, cables form motor to starter panel & other required accessories & tested as per IS Specifications.

Vertical Turbine

Rates are inclusive of all equipments / accessories required for satisfactory & Successful execution of electromechanical system in water supply pumping system based on different type of pumping machinery but exclude cost of operation , maintanance & Repairs . Pleae refer basic & mandatory electrical & mechanical component of water supply pumping system & design guide lines in brief attached here with

S.O.R. Mech 2019-20Page 107 of 166

Section- "E"


Rates inclusive of

GST




6.3 7.5 T 9 m - 12 m

12 m 6 m - 10 m

set 645,000 25,000 670,000 18% 790,600

38A

Sr No Capacity Span Long travel

Lift

Tonne m m m

1.1 10 T 0 m - 6 m

12 m 6 m - 10 m

set 825,000 25,000 850,000 18% 1,003,000

1.2 10 T 6 m - 9 m

12 m 6 m - 10 m

set 950,000 25,000 975,000 18% 1,150,500

1.3 10 T 9 m - 12 m

12 m 6 m - 10 m

set 1,090,000 25,000 1,115,000 18% 1,315,700

2.1 15 T 0 m - 6 m

12 m 6 m - 10 m

set 1,050,000 25,000 1,075,000 18% 1,268,500

2.2 15 T 6 m - 9 m

12 m 6 m - 10 m

set 1,400,000 25,000 1,425,000 18% 1,681,500

2.3 15 T 9 m - 12 m

12 m 6 m - 10 m

set 1,595,000 25,000 1,620,000 18% 1,911,600

3.1 20 T 0 m - 6 m

12 m 6 m - 10 m

set 1,600,000 25,000 1,625,000 18% 1,917,500

3.2 20 T 6 m - 9 m

12 m 6 m - 10 m

set 1,675,000 25,000 1,700,000 18% 2,006,000

3.3 20 T 9 m - 12 m

12 m 6 m - 10 m

set 1,810,000 25,000 1,835,000 18% 2,165,300

38B

Sr No Capacity Diameter of

PumpHouse/ Intake

Long travel

Lift

Tonne m m m

1.1 10 T 0 m - 6 m

12 m 6 m - 10 m

set 850,000 45,000 895,000 18% 1,056,100

1.2 10 T 6 m - 9 m

12 m 6 m - 10 m

set 975,000 45,000 1,020,000 18% 1,203,600

1.3 10 T 9 m - 12 m

12 m 6 m - 10 m

set 1,250,000 45,000 1,295,000 18% 1,528,100

2.1 15 T 0 m - 6 m

12 m 6 m - 10 m

set 1,075,000 45,000 1,120,000 18% 1,321,600

2.2 15 T 6 m - 9 m

12 m 6 m - 10 m

set 1,275,000 45,000 1,320,000 18% 1,557,600

2.3 15 T 9 m - 12 m

12 m 6 m - 10 m

set 1,350,000 45,000 1,395,000 18% 1,646,100

3.1 20 T 0 m - 6 m

12 m 6 m - 10 m

set 1,275,000 65,000 1,340,000 18% 1,581,200

3.2 20 T 6 m - 9 m

12 m 6 m - 10 m

set 1,460,000 65,000 1,525,000 18% 1,799,500

3.3 20 T 9 m - 12 m

12 m 6 m - 10 m

set 1,850,000 85,000 1,935,000 18% 2,283,300

39

1 T 6 m set 12,000 Incl. 12,000 12% 13,440.00

Additional lift 1 m set 500 Incl. 500 5% 525.00

2 T 6 m set 14,500 Incl. 14,500 12% 16,240.00

Additional lift 1 m set 700 Incl. 700 5% 735.00

3 T 6 m set 18,800 Incl. 18,800 12% 21,056.00

Additional lift 1 m set 1,200 Incl. 1,200 5% 1,260.00

Double Girder E.O.T. Crane

Providing & erecting Double girder type fully electrically operated E.O.T. crane with electrically operated hoist, class II duty, geared travelling trolley with seven meter lift complete with long travel rail track (40 mm sq. bar), moving or cross girder, all three motions electrically operated by suitable rating motor IP 54, control panel & down pendant control block, brake, safety device, cables form motor to starter panel & other required accessories & tested as per IS Specifications

Double Girder Circular E.O.T. Crane

Chain Pulley Block

Providing Chain pulley block with triple gear arrangement, lifting hook, laod chain & hand chain & locking device etc

ManuallyOperatedManuallyOperatedManuallyOperatedManuallyOperatedMotorizedOperatedMotorizedOperated

40 LV APFC PANEL

S.O.R. Mech 2019-20Page 108 of 166

Section- "E"


Rates inclusive of

GST




40.1

No 108,691 7,575 116,266 18% 137,194

40.2

No 150,097 7,575 157,672 18% 186,053

40.3

No 205,000 7,575 212,575 18% 250,839

40.4

No 362,303 7,575 369,878 18% 436,456

40.5

No 533,103 7,575 540,678 18% 638,000

41

41.1

1 W No. 20034 2525.00 22559 18% 26,620

2 W + 1 S

No. 85180 4545.00 89725 18% 105,876

3 W + 2 S

No. 128255 5050.00 133305 18% 157,300

Supply, installaton, testing & commissioning LV APFC panel consisting of required capacitor banks for continuous duty to improve P.F. 0.85 to 0.99 in required steps enclosed in dust & vermin proof compartment, indoor type, fabricated from CRCA sheet steel with minimum thickness of 3 mm for base frame / channel / gland plates, 2.0 mm for load bearing members / doors & 1.6 mm for internal partitions, minimum degree of protection - IP 42, busbar chamber, required size of Al bus bar/ terminals, minimum 10 stage APFC relay, metering, indicating lamps, push buttons, with detuned reactor complete as per IS: 16636-2017 with latest ammendment & detailed technical specification and data sheet as under.

Up to 50 KVAR capacity: APFC panel consisting following items. a) 125 A, 50 kA for 1sec. TP, TM based MCCB with spreader terminals & rotary handle b) 0-125 A range analogue ammeter of 96 x 96 mm size with selector switch c) 3nos. 125 / 5A, 10 VA CL-1.0 cast resin type current transformer d) Suitable rating MCCB / MCB &Contactors for each capacitor bank e) Suitable rating APP type capacitor banks (vacuum impregnated with non-PCB / non toxic oil, internally delta connected with built in internal fuses complete with discharge resistances & terminal cover) of approoved make in required steps with well suited detuned reactor is placed in series with each capacitor step. (e.g., 50 KVAR capacity will be provided in steps of 2 nos x 5 KVAR, 2 nos x 7.5KVAR & 2 nos x12.5 KVAR). f) Enclosure dimensions- 1600 (H) x 1150 (W) x 600 (D)

As per above specification

Above 50 & up to 100 KVAR: APFC panel consisting following items. a) 250 A, 50kA for 1sec. TP, TM based MCCB with spreader terminals & rotary handle b) 0-250 A range analogue ammeter of 96 x 96 mm size with selector switch c) 3nos. 250 / 5A, 10 VA CL-1.0 cast resin type current transformer d) Suitable rating of MCCB / MCB & Contactors for each capacitor bank e) Suitable rating APP type capacitor banks (vacuum impregnated with non-PCB / non toxic oil, internally delta connected with built in internal fuses complete with discharge resistances & terminal cover) of approved make in required steps with well suited detuned reactor is placed in series with each capacitor step. ( e.g., 100 KVAR capacity will be provided in steps of 2 nos x 5 KVAR, 2 nos x 10KVAR, 2 nos x 15 KVAR & 2 nos x 20 KVAR) f) Enclosre dimensions- 2100 (H) x 1150 (W) x 600 (D)


Above 100 & up to 200 KVAR: APFC panel consisting following items.a) 400 A, 50 kA for 1sec. TP, TM based MCCB with spreader terminals & rotary handle b) 0-400 A range analogue ammeter of 96 x 96 mm size with selector switch c) 3nos. 400 / 5A, 10 VA CL-1.0 cast resin type current transformer d) Suitable rating of MCCB / MCB & Contractors for each capacitor bank e) Suitable rating APP type capacitor banks (vacuum impregnated with non-PCB / non toxic oil, internally delta connected with built in internal fuses complete with discharge resistances & terminal cover) of approved make in required steps with well suited detuned reactor is placed in series with each capacitor step. (e.g., 200 KVAR capacity will be provided in steps of 2 nos x 5 KVAR, 2 nos x 15KVAR, 2 nos x 30 KVAR & 2 nos x 50 KVAR) f) Enclosure dimensions- 2100 (H) x 1250 (W) x 600 (D)


2200 x 600 x 2175

Above 200 & up to 300 KVAR: APFC panel consisting following items. a) 630 A, 50 kA for 1sec. TP, TM based MCCB with spreader terminals & rotary handle b) 0-630 A range analogue ammeter of 96 x 96 mm size with selector switch c) 3nos. 630/5A, 10 VA CL-1.0 cast resin type current transformer d) Suitable rating of MCCB/ MCB & Contractor for each capacitor bank e) Suitable rating APP type capacitor banks (vacuum impregnated with non-PCB/ non toxic oil, internally delta connected with built in internal fuses complete with discharge resistances & terminal cover) of approved make in required steps (e.g., 300 KVAR capacity will be provided in steps of 2nos x 5 KVAR, 2 nos x 10 KVAR, 2 nos x 15KVAR, 2 nos x 20 KVAR, & 4 nos x 50 KVAR) f) Enclosure dimensions- 1900 (H) x 1200 (W) x 600 (D)


Above 300 & up to 400 KVAR: APFC panel consisting following items. a) 800 A, 50 kA for 1sec. TP, MDO type, ACB with TM based release & accessories b) 0-800 A range analogue ammeter of 96 x 96 mm size with selector switch c) 3nos. 800 / 5A, 10 VA CL-1.0 cast resin type current transformer d) Suitable rating of MCCB/ MCB & Contractor for each capacitor bank e) Suitable rating APP type capacitor banks (vacuum impregnated with non-PCB / non toxic oil, internally delta connected with built in internal fuses complete with discharge resistances & terminal cover) of approved make in required steps with well suited detuned reactor is placed in series with each capacitor step. (e.g., 400 KVAR capacity will be provided in steps of 2 nos x 5 KVAR, 2 nos x 10 KVAR, 2 nos x 15KVAR, 2 nos x 20 KVAR & 6 nos x 50 KVAR) f) Enclosre dimensions- 2100 (H) x 1250 (W) x 1000 (D)


LV MCC Panel with ATS / Micro processor based soft starter

S.I.T.C of LV MCC Panel totally enclosed, dust & bermin proof, indoor type, minimum degree of protection - IP 52 as per IS: 2147, operation on 3-Phase, 4 Wire, 415V, 50Hz, Neutral effectively grounded, with instrumentation compartments accomodating LED type indicating lamps, control contactors as per IS: 13947, CT of accuracy class- I as per IS: 2705, relays, meters & control MCBs, air insulated electrolitic grade Aluminum busbar for three phase & neutral system with incomming breaker- microprocessor based Air Circuit Breakers (electrically operated drawout type)/ air break fixed type MCCB with trip free mechanism, current limiting type as per IS: 8828, Motor Contractor (as per type -2 coordination), Overload Relay with built-in single phasing prevention feature & auxiliary feeders as per SLD drawings, momentary contact type push buttons, equipment fittings, bus bars, cable boxes, cable gland, incoming & ougoing cable connection for 1100V grade, Aluminium/ Copper conductor XLPE/ PVC insulated & PVC sheathed armoured cable, 10% spare terminals, power wiring using 1100V grade, FRLS insulated copper conductor wires conforming to IS: 694 & 8130, cable compartments/ alleys of minimum 300 mm size, GI earth bus bar for entire length. MCC shall be fabricated from cold rolled, coled annealed (CRCA) sheet steel & minimum thickness of various members shall be as follows:Base Frame/ Channel/ Gland Plate - 3 mm, Load Bearing Members/ Doors - 2 mm and Internal Partitions - 1.6 mm.

Auto Transformer Starter with MCCB, Contactor, O/L relay, cast resin type CT, Digital MFM, Analog Ammeter, SPP, Timer etc.

a 22 700 x 450 x 800

1500 x 600 x 2175

S.O.R. Mech 2019-20Page 109 of 166

Section- "E"


Rates inclusive of

GST




1 W No. 28750 2525.00 31275 18% 36,905

2 W + 1 S

No. 113379 4545.00 117924 18% 139,150

3 W + 2 S

No. 148764 5050.00 153814 18% 181,501

1 W No. 39503 4545.00 44048 18% 51,977

2 W + 1 S

No. 153891 5050.00 158941 18% 187,550

3 W + 2 S

No. 205162 5050.00 210212 18% 248,050

1 W No. 40977 5050.00 46027 18% 54,312

2 W + 1 S

No. 169272 5050.00 174322 18% 205,700

3 W + 2 S

No. 225670 5050.00 230720 18% 272,250

1 W No. 45700 5050.00 50750 18% 59,885

2 W + 1 S

No. 212070 5050.00 217120 18% 256,202

3 W + 2 S

No. 303979 5050.00 309029 18% 364,654

41.2

1 W No. 108106 6060.00 114166 18% 134,715

2 W + 1 S

No. 461169 7070.00 468239 18% 552,522

3 W + 2 S

4100 x 600 x 2175

4100 x 600 x 2175

No. 699761 7070.00 706831 18% 834,061

1 W No. 126555 6060.00 132615 18% 156,486

2 W + 1 S

No. 562320 7070.00 569390 18% 671,880

3 W + 2 S

No. 815431 7070.00 822501 18% 970,551

1 W No. 126555 7070.00 133625 18% 157,678

2 W + 1 S

No. 570000 7070.00 577070 18% 680,943

3 W + 2 S

No. 857581 7070.00 864651 18% 1,020,289

1 W No. 145391 7070.00 152461 18% 179,904

2 W + 1 S

No. 651304 7070.00 658374 18% 776,882

3 W + 2 S

4400 x 900/600 x

4400 x 900/60

0 x

No. 951269 7070.00 958339 18% 1,130,840

1 W No. 164025 7070.00 171095 18% 201,893

2 W + 1 S

No. 613000 7070.00 620070 18% 731,683

3 W + 2 S

No. 970000 7070.00 977070 18% 1,152,943

1 W No. 182756 7070.00 189826 18% 223,995

2 W + 1 S

No. 690000 7070.00 697070 18% 822,543

3 W + 2 S

No. 1087000 7070.00 1094070 18% 1,291,003

1 W No. 196584 7070.00 203654 18% 240,312

2 W + 1 S

No. 823920 7070.00 830990 18% 980,568

3 W + 2 S

4400 x 900/600 x

4400 x 900/60

0 x

No. 1217088 7070.00 1224158 18% 1,444,506

1 W No. 204715 7070.00 211785 18% 249,906

2 W + 1 S

No. 858064 7070.00 865134 18% 1,020,859

3 W + 2 S

No. 1267894 7070.00 1274964 18% 1,504,457

1 W No. 220225 8585.00 228810 18% 269,996

2 W + 1 S

No. 913579 8585.00 922164 18% 1,088,153

3 W + 2 S

No. 1363396 8585.00 1371981 18% 1,618,937

b 30 700 x 450 x 800

1500 x 600 x 2175

2200 x 600 x 2175

c 37 700 x 450 x 800

1500 x 600 x 2175

2200 x 600 x 2175

d 45 700 x 450 x 800

1500 x 600 x 2175

2200 x 600 x 2175

e 55 700 x 450 x 800

1500 x 600 x 2175

2200 x 600 x 2175

Microprocessor based Soft Starter with built-in by pass contactor,Semiconductor Fuses, Harmonic Filters, cast resin type CT, Digital MFM, Analog Ammeter & minimum 10 Channel Temperature Scanner with RS 485 communication port.

4400 x 900/600 x 2175

a 75 700 x 600 x 2175

2700 x 600 x 2175

b 90 700 x 600 x 2175

2700 x 600 x 2175

4100 x 600 x 2175

c 110 700 x 600 x 2175

2700 x 600 x 2175

f 160 700 x 600 x 2175

3000 x 900/600 x 2175

4400 x 900/600 x 2175

d 125 700 x 600 x 2175

2700 x 600 x 2175

g 180 700 x 600 x 2175

3000 x 900/600 x 2175

e 132 700 x 600 x 2175

2700 x 600 x 2175

4400 x 900/600 x 2175

h 200 700 x 600 x 2175

3000 x 900/600 x 2175

4400 x 900/600 x 2175

i 225 700 x 600 x 2175

3000 x 900/600 x 2175

4400 x 900/600 x 2175

S.O.R. Mech 2019-20Page 110 of 166

Section- "E"


Rates inclusive of

GST




1 W No. 248331 8585.00 256916 18% 303,161

2 W + 1 S

No. 1007650 8585.00 1016235 18% 1,199,158

3 W + 2 S

No. 1560126 8585.00 1568711 18% 1,851,079

1 W No. 261953 8585.00 270538 18% 319,235

2 W + 1 S

No. 1020026 8585.00 1028611 18% 1,213,761

3 W + 2 S

No. 1562665 8585.00 1571250 18% 1,854,075

1 W No. 280583 8585.00 289168 18% 341,218

2 W + 1 S

No. 1079665 8585.00 1088250 18% 1,284,135

3 W + 2 S

No. 1655817 8585.00 1664402 18% 1,963,994

1 W No. 351386 8585.00 359971 18% 424,766

2 W + 1 S

No. 1307058 8585.00 1315643 18% 1,552,458

3 W + 2 S

No. 1991095 8585.00 1999680 18% 2,359,622

41.3

1 W No. 118262 6060.00 124322 18% 146,700

2 W + 1 S

No. 492104 7070.00 499174 18% 589,025

3 W + 2 S

No. 752302 7070.00 759372 18% 896,059

1 W No. 125524 6060.00 131584 18% 155,270

2 W + 1 S

No. 513894 7070.00 520964 18% 614,738

3 W + 2 S

No. 788621 7070.00 795691 18% 938,915

1 W No. 131204 7070.00 138274 18% 163,163

2 W + 1 S

No. 530932 7070.00 538002 18% 634,843

3 W + 2 S

No. 817017 7070.00 824087 18% 972,422

1 W No. 140040 7070.00 147110 18% 173,590

2 W + 1 S

No. 557441 7070.00 564511 18% 666,123

3 W + 2 S

No. 861195 7070.00 868265 18% 1,024,553

1 W No. 156469 7070.00 163539 18% 192,976

2 W + 1 S

No. 601991 7070.00 609061 18% 718,692

3 W + 2 S

No. 943340 7070.00 950410 18% 1,121,484

1 W No. 169054 7070.00 176124 18% 207,826

2 W + 1 S

No. 639746 7070.00 646816 18% 763,243

3 W + 2 S

No. 1006265 7070.00 1013335 18% 1,195,735

1 W No. 226099 7070.00 233169 18% 275,139

2 W + 1 S

No. 810881 7070.00 817951 18% 965,182

3 W + 2 S

No. 1291492 7070.00 1298562 18% 1,532,303

1 W No. 242436 7070.00 249506 18% 294,417

2 W + 1 S

No. 859892 7070.00 866962 18% 1,023,016

3 W + 2 S

No. 1373176 7070.00 1380246 18% 1,628,691

1 W No. 251072 8585.00 259657 18% 306,396

2 W + 1 S

No. 885802 8585.00 894387 18% 1,055,377

3 W + 2 S

No. 1416360 8585.00 1424945 18% 1,681,435

250 700 x 600 x 2175

3000 x 900/600 x 2175

4400 x 900/600 x 2175

k 300 800 x 900 x 2175

3000 x 900/600 x 21755000 x

1200/900 x 2175800 x 900 x 2175

3300 x 1200/900 x

21755000 x 1200/900 x

2175m 375 800 x 900 x 2175

3300 x 1200/900 x

21755000 x 1200/900 x

2175Microprocessor based Soft Starter with external by pass contactor,Line Contactor,Semiconductor Fuses, Harmonic Filters, cast resin type CT, Digital MFM, Analog Ammeter & minimum 10 Channel Temperature Scanner with RS 485 communication port.

j

a 75 700 x 600 x 2175

l 315

4100 x 600 x 2175

b 90 700 x 600 x 2175

2700 x 600 x 2175

4100 x 600 x 2175

c 110 700 x 600 x 2175

2700 x 600 x 2175

4400 x 900/600 x 2175

d 125 700 x 600 x 2175

2700 x 600 x 2175

4400 x 900/600 x 2175

e 132 700 x 600 x 2175

2700 x 600 x 2175

4400 x 900/600 x 2175

f 160 700 x 600 x 2175

3000 x 900/600 x 2175

4400 x 900/600 x 2175

g 180 700 x 600 x 2175

3000 x 900/600 x 2175

4400 x 900/600 x 2175

h 200 700 x 600 x 2175

3000 x 900/600 x 2175

4400 x 900/600 x 2175

i 225 700 x 600 x 2175

3000 x 900/600 x 2175

4400 x 900/600 x 2175

2700 x 600 x 2175

S.O.R. Mech 2019-20Page 111 of 166

Section- "E"


Rates inclusive of

GST




1 W No. 282700 8585.00 291285 18% 343,717

2 W + 1 S

No. 980684 8585.00 989269 18% 1,167,337

3 W + 2 S

No. 1574495 8585.00 1583080 18% 1,868,034

1 W No. 307891 8585.00 316476 18% 373,442

2 W + 1 S

No. 1056256 8585.00 1064841 18% 1,256,513

3 W + 2 S

No. 1700451 8585.00 1709036 18% 2,016,663

1 W No. 345802 8585.00 354387 18% 418,177

2 W + 1 S

No. 1169899 8585.00 1178484 18% 1,390,611

3 W + 2 S

No. 1889856 8585.00 1898441 18% 2,240,161

1 W No. 377334 8585.00 385919 18% 455,385

2 W + 1 S

No. 1264584 8585.00 1273169 18% 1,502,339

3 W + 2 S

No. 2047663 8585.00 2056248 18% 2,426,372

42

42.1

a Set 3,589,070 22,725 3,611,795 18.00% 4,261,918

b Set 3,589,070 22,725 3,611,795 18% 4,261,918

c Set 3,589,070 22,725 3,611,795 18% 4,261,918

d Set 3,046,005 22,725 3,068,730 18% 3,621,101

e Set 3,046,005 22,725 3,068,730 18% 3,621,101

f Set 3,046,005 22,725 3,068,730 18% 3,621,101

j 250 700 x 600 x 2175

3000 x 900/600 x 2175

4400 x 900/600 x 2175

800 x 900 x 2175

3000 x 900/600 x 21755000 x

1200/900 x 2175l 315 800 x 900 x 2175

3300 x 1200/900 x

21755000 x 1200/900 x

2175m 375 800 x 900 x 2175

3300 x 1200/900 x

21755000 x 1200/900 x

2175HV VCB SWITCHGEAR PANEL

k 300

Supply, installation, testing & commissioning both side extensible, Indoor type HV Switchgear panel confirming to IS-3427, IS-2516 (Part-I & II.sec.1 ) & IEC-60056 & IEC-62271-100/200 for use on 3phase, 50 Hz, unearthed AC supply system and having breaking/ ruptuing capacity of 150 MVA (26.3 kA for 3sec) complete with spring charged mechanism, ON-OFF mechanical push button, operation counters, Breaker TNC switch, Breaker L/R switch, necessary auxiliary switches, closing coil, shunt trip, protection relays & Indicators etc., complete.The panel shall comprise of air insulated busbars provided with heat shrinkable PVC sleeves. The VCB trolley shall comprise of three vacuum interrupters with epoxy support insulators and self aligning finger type isolating contacts and necessary mechanical interlocks, safety shutters, isolating plugs. Enclosure shall be openable from front as well as rear end. The breaker shall be Manual cum motorised mechanism with following accessories. a) 96 x 96 mm square flush mounting type Ammeter & Volt meter with selector switchesb) Multi function meterc) Double core, cast resin type current transofrmer having ratio as per requirement, one core for metering & one core for protection having required class of accuracy. d) Instantaneous under voltage relay & Temperature rise tripping Relay, e) Triple pole IDMTL two over current and one earth fault relay with current setting range 50-200% and 10-40%f) Electrical closing. coil & shunt trip coil operating on 110 V DC. g) Auxiliary relay for anti pumping device. h) Three limb, drawout type, feeder connected, cast resin insulated, three phase Potential transformer having ratio & burden as per reqirement & Class 0.5 accuracy. i) Annunciator Windows, Common Hooter / Alarm bell operating on 230 AC / 110 V DCj) Cable boxes suitable to terminate 3 core XLPE cable of required size (As per design).k) 230V A.C. to 110 V D.C.power pack for closing & tripping circuit common. l) Breaker ON-OFF, Auto trip and spring charged indicators. m) Phase indicating & panel illumination lamps with plug socket.n) Space Heater with Thermostat. 3.3 kV HV Switchgear Panel- Comprising of 1250 A Vacuum circuit breaker for 2 nos. Incomer, 1no. Bus coupler, 8 nos. O/G feeders for Motor Soft Starters, 2nos. O / G for 3.3 / 0.433kV Auxiliary transformers

3.3 kV HV Switchgear Panel- Comprising of 800 A Vacuum circuit breaker for 2nos. Incomer, 1no. Bus coupler, 8 nos. O/G feeders for Motor Soft Starters, 2 nos. O/G for 3.3 / 0.433kV Auxiliary transformers

3.3 kV HV Switchgear Panel- Comprising of 630 A Vacuum circuit breaker for 2nos. Incomer, 1no. Bus coupler, 8 nos. O/G feeders for Motor Soft Starters, 2nos. O/G for 3.3 / 0.433kV Auxiliary transformers

3.3 kV HV Switchgear Panel- Comprising of 1250 A Vacuum circuit breaker for 2nos. Incomer, 1no. Bus coupler, 6 nos. O/G feeders for Motor Soft Starters, 2nos. O / G for 3.3 / 0.433kV Auxiliary transformers

3.3 kV HV Switchgear Panel- Comprising of 800 A Vacuum circuit breaker for 2nos. Incomer, 1no. Bus coupler, 6 nos. O/G feeders for Motor Soft Starters, 2nos. O/G for 3.3 / 0.433kV Auxiliary transformers

3.3 kV HV Switchgear Panel- Comprising of 630 A Vacuum circuit breaker for 2nos. Incomer, 1no. Bus coupler, 6 nos. O/G feeders for Motor Soft Starters, 2nos. O / G for 3.3 / 0.433kV Auxiliary transformers

S.O.R. Mech 2019-20Page 112 of 166

Section- "E"


Rates inclusive of

GST




42.2

a Set 3,589,070 27,270 3,616,340 18.00% 4,267,281

b Set 3,589,070 27,270 3,616,340 18.00% 4,267,281

c Set 3,066,964 27,270 3,094,234 18% 3,651,196

d Set 3,046,005 27,270 3,073,275 18% 3,626,465

e Set 3,046,005 27,270 3,073,275 18% 3,626,465

f Set 3,046,005 27,270 3,073,275 18% 3,626,465

42.3

a Set 3,589,070 31,815 3,620,885 18.00% 4,272,644

Supply, installation, testing & commissioning both side extensible, Indoor type HV Switchgear panel confirming to IS-3427, IS-2516 (Part-I & II.sec.1 ) & IEC-60056 & IEC-62271-100/200 for use on 3phase, 50 Hz, unearthed AC supply system and having breaking/ ruptuing capacity of 500 MVA (26.3 kA for 3sec) complete with spring charged mechanism, ON-OFF mechanical push button, operation counters, Breaker TNC switch, Breaker L/R switch, necessary auxiliary switches, closing coil, shunt trip, protection relays & Indicators etc., complete.The panel shall comprise of air insulated busbars provided with heat shrinkable PVC sleeves. The VCB trolley shall comprise of three vacuum interrupters with epoxy support insulators and self aligning finger type isolating contacts and necessary mechanical interlocks, safety shutters, isolating plugs. Enclosure shall be openable from front as well as rear end. The breaker shall be Manual cum motorised mechanism with following accessories. a) 96 x 96 mm square flush mounting type Ammeter & Volt meter with selector switchesb) Multi function meterc) Double core, cast resin type current transofrmer having ratio as per requirement, one core for metering & one core for protection having required class of accuracy. d) Instantaneous under voltage relay & Temperature rise tripping Relay, e) Triple pole IDMTL two over current and one earth fault relay with current setting range 50-200% and 10-40%f) Electrical closing. coil & shunt trip coil operating on 110 V DC. g) Auxiliary relay for anti pumping device. h) Three limb, drawout type, feeder connected, cast resin insulated, three phase Potential transformer having ratio & burden as per reqirement & Class 0.5 accuracy. i) Annunciator Windows, Common Hooter / Alarm bell operating on 230 AC/ 110 V DCj) Cable boxes suitable to terminate 3 core XLPE cable of required size (As per design).k) 230V A.C. to 110 V D.C.power pack for closing & tripping circuit common. l) Breaker ON-OFF, Auto trip and spring charged indicators. m) Phase indicating & panel illumination lamps with plug socket.n) Space Heater with Thermostat. 6.6 kV HV Switchgear Panel- Comprising of 1250 A Vacuum circuit breaker for 2nos. Incomer, 1no. Bus coupler, 8 nos. O/G feeders for Motor Soft Starters, 2 nos. O / G for 6.6 / 0.433kV Auxiliary transformers




6.6 kV HV Switchgear Panel- Comprising of 800 A Vacuum circuit breaker for 2nos. Incomer, 1no. Bus coupler, 6 nos. O/G feeders for Motor Soft Starters, 2 nos. O/G for 6.6 / 0.433kV Auxiliary transformers 6.6 kV HV Switchgear Panel- Comprising of 630 A Vacuum circuit breaker for 2nos. Incomer, 1no. Bus coupler, 6 nos. O/G feeders for Motor Soft Starters, 2nos. O/G for 6.6 / 0.433kV Auxiliary transformers

Supply, installation, testing & commissioning both side extensible, Indoor type HV Switchgear panel confirming to IS-3427, IS-2516 (Part-I & II.sec.1 ) & IEC-60056 & IEC-62271-100/200 for use on 3phase, 50 Hz, unearthed AC supply system and having breaking/ ruptuing capacity of 500 MVA (26.3 kA for 3sec) complete with spring charged mechanism, ON-OFF mechanical push button, operation counters, Breaker TNC switch, Breaker L/R switch, necessary auxiliary switches, closing coil, shunt trip, protection relays & Indicators etc., complete.The panel shall comprise of air insulated busbars provided with heat shrinkable PVC sleeves. The VCB trolley shall comprise of three vacuum interrupters with epoxy support insulators and self aligning finger type isolating contacts and necessary mechanical interlocks, safety shutters, isolating plugs. Enclosure shall be openable from front as well as rear end. The breaker shall be Manual cum motorised mechanism with following accessories. a) 96 x 96 mm square flush mounting type Ammeter & Volt meter with selector switchesb) Multi function meterc) Double core, cast resin type current transofrmer having ratio as per requirement, one core for metering & one core for protection having required class of accuracy. d) Instantaneous under voltage relay & Temperature rise tripping Relay, e) Triple pole IDMTL two over current and one earth fault relay with current setting range 50-200% and 10-40%f) Electrical closing. coil & shunt trip coil operating on 110 V DC. g) Auxiliary relay for anti pumping device. h) Three limb, drawout type, feeder connected, cast resin insulated, three phase Potential transformer having ratio & burden as per reqirement & Class 0.5 accuracy. i) Annunciator Windows, Common Hooter / Alarm bell operating on 230 AC/ 110 V DCj) Cable boxes suitable to terminate 3 core XLPE cable of required size (As per design).k) 230V A.C. to 110 V D.C.power pack for closing & tripping circuit common. l) Breaker ON-OFF, Auto trip and spring charged indicators. m) Phase indicating & panel illumination lamps with plug socket. n) Space Heater with Thermostat. 11 kV HV Switchgear Panel- Comprising of 1250 A Vacuum circuit breaker for 2 nos. Incomer, 1no. Bus coupler, 8 nos. O/G feeders for Motor Soft Starters, 2nos. O / G for 11 / 0.433kV Auxiliary transformers

S.O.R. Mech 2019-20Page 113 of 166

Section- "E"


Rates inclusive of

GST




b Set 3,589,070 31,815 3,620,885 18% 4,272,644

c Set 3,589,070 31,815 3,620,885 18% 4,272,644

d Set 3,046,005 31,815 3,077,820 18% 3,631,828

e Set 3,046,005 31,815 3,077,820 18% 3,631,828

f Set 3,046,005 31,815 3,077,820 18% 3,631,828

g Set 843,008 31,815 874,823 18% 1,032,291

h Set 801,090 31,815 832,905 18% 982,828

i Set 797,830 31,815 829,645 18% 978,981

j Set 281,779 31,815 313,594 18% 370,041

k Set 281,779 31,815 313,594 18% 370,041

l Set 281,779 31,815 313,594 18% 370,041

4343.1.1 No. 47,277 Incl. 47,277 5% 49,641

43.1.2 61,553 Incl. 61,553 5% 64,630

43.1.3 94,554 Incl. 94,554 5% 99,282

43.1.4 171,456 Incl. 171,456 5% 180,029

43.2.1 78,149 Incl. 78,149 12% 87,527

43.2.2 83,812 Incl. 83,812 12% 93,869

43.2.3 93,558 Incl. 93,558 12% 104,785

43.2.4 103,000 Incl. 103,000 12% 115,360

Supply DC Voltage Submersible pump Discharge 10000 LPD for 170 Mtr. With Controller Drive.Supply DC Submersible pump Discharge 10000 LPD for 200 Mtr. With Controller Drive. MOC: SS 316

11 kV HV Switchgear Panel- Comprising of 800 A Vacuum circuit breaker for 1no. Incomer, 2no. O / G feeders for 11/0.433kV distribution transformers

Solar System

11 kV HV Switchgear Panel- Comprising of 800 A Vacuum circuit breaker for 2 nos. Incomer, 1no. Bus coupler, 8 nos. O/G feeders for Motor Soft Starters, 2nos. O / G for 11 / 0.433kV Auxiliary transformers

11 kV HV Switchgear Panel- Comprising of 630 A Vacuum circuit breaker for 2nos. Incomer, 1no. Bus coupler, 8 nos. O/G feeders for Motor Soft Starters, 2nos. O / G for 11 / 0.433kV Auxiliary transformers

11 kV HV Switchgear Panel- Comprising of 1250 A Vacuum circuit breaker for 2nos. Incomer, 1no. Bus coupler, 6 nos. O/G feeders for Motor Soft Starters, 2nos. O/G for 11 / 0.433kV Auxiliary transformers

11 kV HV Switchgear Panel- Comprising of 800 A Vacuum circuit breaker for 2nos. Incomer, 1no. Bus coupler, 6 nos. O/G feeders for Motor Soft Starters, 2nos. O/G for 11 / 0.433kV Auxiliary transformers

11 kV HV Switchgear Panel- Comprising of 630 A Vacuum circuit breaker for 2nos. Incomer, 1no. Bus coupler, 6 nos. O/G feeders for Motor Soft Starters, 2 nos. O/G for 11 / 0.433kV Auxiliary transformers

11 kV HV Switchgear Panel- Comprising of 1250 A Vacuum circuit breaker for 1no. Incomer, 2 nos. O / G feeders for 11/0.433kV distribution transformers

Supply Solar PV Panels 1200 wp, Each modules not less then 175 wp should be in accordance with requirement of national & international certificates such as IEC 61215 & 61730 for DC type Submersible pump with MPPT controller.



Supply DC Submersible pump Discharge 10000 LPD for 120 Mtr. With Controller Drive. MOC: SS 316

11 kV HV Switchgear Panel- Comprising of 630 A Vacuum circuit breaker for 1no. Incomer, 2no. O / G feeders for 11/0.433kV distribution transformers

11 kV HV ICOG Switchgear Panel- Comprising of 1250 A Vacuum circuit breaker for 1no. Incomer, 1no. O / G feeders for 11/0.433kV distribution transformers




Supply DC Submersible pump Discharge 7200 LPD for 90 Mtr. With Controller Drive. MOC: SS 316

S.O.R. Mech 2019-20Page 114 of 166

Section- "E"


Rates inclusive of

GST




43.3.1 48,435 Incl. 48,435 18% 57,154

43.3.2 62,000 Incl. 62,000 18% 73,160

43.3.3 77,172 Incl. 77,172 18% 91,063

43.3.4 108,781 Incl. 108,781 18% 128,362

43.4.1 15,434 Incl. 15,434 18% 18,212

43.4.2 16,467 Incl. 16,467 18% 19,430

43.4.3 21,258 Incl. 21,258 18% 25,084

43.4.5 32,607 Incl. 32,607 18% 38,477

44

A

1 per KW

9,695.00 - 9,695.00 12% 10,858

2 per KW

9,695.00 - 9,695.00 12% 10,858

3 per KW

10,115.00 - 10,115.00 12% 11,329

4 per KW

11,000.00 - 11,000.00 12% 12,320

5 per KW

11,000.00 - 11,000.00 12% 12,320

B

1 Job - 19,950.00 19,950.00 5% 20,948

2 Job - 33,250.00 33,250.00 5% 34,913

3 Job - 53,200.00 53,200.00 5% 55,860

4 Job - 80,000.00 80,000.00 5% 84,000

5 Job - 80,000.00 80,000.00 5% 84,000

45

1

1.1

1.1a No. 280,963 5,500 286,463 18% 338,026

1.1b No. 301,527 5,500 307,027 18% 362,292

1.1c No. 286,995 5,500 292,495 18% 345,144

1.1d No. 307,558 5,500 313,058 18% 369,408

1.1e No. 338,996 5,500 344,496 18% 406,505

1.1f No. 359,536 5,500 365,036 18% 430,742

---as above---1800Wp






LV POWER CONTROL CENTER (PCC)

Supply, installation, testing and commissioning LV Distribution Board (LVDB) totally enclosed, dust & vermin proof, indoor type, fabricated from CRCA sheet steel with minimum thickness of 3 mm for base frame/ channel/ gland plates, 2.0 mm for load bearing members/ doors & 1.6 mm for internal partitions, minimum degree of protection - IP 52 as per IS: 2147, suitable for operation on 3-Phase, 4 Wire, 415V, 50Hz, Neutral effectively grounded, with instrumentation compartments accomodating meters, aux / protective relays, LED type indicating lamps & control MCBs as per IS: 13947, current & voltage transformers as per IS: 2705, air insulated electrolitic grade Aluminum/ Copper busbar for three phase & neutral system, GI earth bus for entire length, power/ control wiring using 1100V grade, FRLS insulated copper conductor wires conforming to IS: 694 & 8130, equipment fittings, horizontally running busbar compartment height of minimum 300 mm, incoming & ougoing cable connections for 1100V grade, Aluminium/ Copper conductor XLPE/ PVC insulated & PVC sheathed armoured cable. LVDB shall have required incomming/ buscoupler/ outgoing modules of following type & ratings.

Part-1

4000A, 3/ 4 Pole, ACB (Draw-out Type) with Thermal Magnetic / Microprocessor release (O / C, S / C & E / F) having breaking capacity Icu of 70 kA at 415V with 6NO+6NC potential feee auxiliary contacts, secondary isolating contacts with all necessary Electro-Mechanical protections & interlocks etc. ACB Module shall have enclosure dimension: 2000 (H) x 1100 (W) x 1200 (D) & following technical features:

3 pole, MDO with Thermal Magnetic Release

3 pole, EDO with Thermal Magnetic Release


3 pole, MDO with Microprocessor Release

3 pole, EDO with Microprocessor Release


Above 315 KW

Erection Charges for Pumpsets (without material supply)

upto 30.0 KW

31.0 KW to 75.0 KW

76.0 KW to 132.0 KW

133 KW to 315 KW

Installation, Testing and Commissiioning of SPV Panel with pole with panel mounting frames. AC/Dc sub. Pump with Solar drive required cableling and G.I.Piping with all installation work with transportation etc with required bar fencing with single gate etc.900Wp

5 Years Comprehensive O&M work of above work with insurance of all items like SPV Panel, Pump, Cable, G.I.Pipe, Controller etc for entire period i.o. 05 years etc.900Wp

Above 315 KW

Providing Submerged centrifugal pumpsets(water immersed, dry air filled, class "F" insulated TEWC motor integrally mounted on volute casing pumpsets for water duty, 3-phase, 50Hz±3%,415V±10% along with suitable foundation/ installation device with cable length from pumps to panels & of following Material of Construction:Impeller-CF8M, Casing-C.I. FG 260, Wearing Ring -SS, TC mechanical seal, CS/S.S.bearing, S.S shaft with sleeve, SS strainer & MS motor body.

Rating

upto 30.0 KW

31.0 KW to 75.0 KW

76.0 KW to 132.0 KW

133 KW to 315 KW

S.O.R. Mech 2019-20Page 115 of 166

Section- "E"


Rates inclusive of

GST




1.1g No. 345,028 5,500 350,528 18% 413,623

1.1h No. 365,567 5,500 371,067 18% 437,859

1.2

1.2a No. 233,113 5,500 238,613 18% 281,563

1.2b No. 255,991 5,500 261,491 18% 308,559

1.2c No. 241,162 5,500 246,662 18% 291,061

1.2d No. 262,497 5,500 267,997 18% 316,236

1.2e No. 276,539 5,500 282,039 18% 332,806

1.2f No. 297,078 5,500 302,578 18% 357,042

1.2g No. 282,570 5,500 288,070 18% 339,923

1.2f No. 303,110 5,500 308,610 18% 364,160

1.3

1.3a No. 176,843 5,500 182,343 18% 215,165

1.3b No. 199,721 5,500 205,221 18% 242,161

1.3c No. 184,891 5,500 190,391 18% 224,661

1.3d No. 207,769 5,500 213,269 18% 251,657

1.3e No. 214,664 5,500 220,164 18% 259,794

1.3f No. 235,017 5,500 240,517 18% 283,810

1.3g No. 220,044 5,500 225,544 18% 266,142

1.3f No. 241,048 5,500 246,548 18% 290,927

1.4

1.4a No. 146,991 5,500 152,491 18% 179,939

1.4b No. 169,869 5,500 175,369 18% 206,935

1.4c No. 155,039 5,500 160,539 18% 189,436

1.4d No. 177,917 5,500 183,417 18% 216,432

1.4e No. 185,987 5,500 191,487 18% 225,955

1.4f No. 208,819 5,500 214,319 18% 252,896

1.4g No. 194,035 5,500 199,535 18% 235,451

1.4f No. 214,851 5,500 220,351 18% 260,014

1.5

1.5a No. 122,474 5,500 127,974 18% 151,009

1.5b No. 145,351 5,500 150,851 18% 178,004

1.5c No. 130,522 5,500 136,022 18% 160,506

1.5d No. 153,399 5,500 158,899 18% 187,501

1.5e No. 151,559 5,500 157,059 18% 185,330



3200A, 3 / 4 Pole, ACB (Draw-out Type) with Thermal Magnetic / Microprocessor release (O / C, S / C & E / F) having breaking capacity Icu of 60 kA at 415V with 6NO+6NC potential feee auxiliary contacts, secondary isolating contacts with all necessary Electro-Mechanical protections & interlocks etc. ACB Module shall have enclosure dimension: 2000(H) x 1100(W) x 1100 (D) & following technical features:






2500A, 3/ 4 Pole, ACB (Draw-out Type) with Thermal Magnetic/ Microprocessor release (O / C, S / C & E / F) having breaking capacity Icu of 60 kA at 415V with 6NO+6NC potential feee auxiliary contacts, secondary isolating contacts with all necessary Electro-Mechanical protections & interlocks etc. ACB Module shall have enclosure dimension: 2000 (H) x 900 (W) x 1100 (D) & following technical features:








2000A, 3 &4 Pole, ACB (Draw-out Type) with Thermal Magnetic/ Microprocessor release (O / C, S / C & E / F) having breaking capacity Icu of 50 kA at 415V with 6NO+6NC potential feee auxiliary contacts, secondary isolating contacts with all necessary Electro-Mechanical protections & interlocks etc. ACB Module shall have enclosure dimension: 2000 (H) x 900 (W) x 1100 (D) & following technical features:Enclosure dimension: 2000(H) x 900(W) x 1100 (D)









1600A, 3 & 4 Pole, ACB (Draw-out Type) with Thermal Magnetic / Microprocessor release (O / C, S / C & E / F) having breaking capacity Icu of 50 kA at 415V with 6NO+6NC potential feee auxiliary contacts, secondary isolating contacts with all necessary Electro Mechanical protections & interlocks etc. ACB Module shall have enclosure dimension: 2000 (H) x 800 (W) x 1000 (D) & following technical features:










S.O.R. Mech 2019-20Page 116 of 166

Section- "E"


Rates inclusive of

GST




1.5f No. 174,437 5,500 179,937 18% 212,326

1.5g No. 159,607 5,500 165,107 18% 194,826

1.5h No. 182,485 5,500 187,985 18% 221,822

1.6

1.6a No. 107,808 5,500 113,308 18% 133,703

1.6b No. 130,685 5,500 136,185 18% 160,698

1.6c No. 115,857 5,500 121,357 18% 143,201

1.6d No. 138,734 5,500 144,234 18% 170,196

1.6e No. 137,221 5,500 142,721 18% 168,411

1.6f No. 160,098 5,500 165,598 18% 195,406

1.6g No. 145,270 5,500 150,770 18% 177,909

1.6h No. 168,147 5,500 173,647 18% 204,903

1.7

1.7a No. 95,728 5,500 101,228 18% 119,449

1.7b No. 118,606 5,500 124,106 18% 146,445

1.7c No. 103,776 5,500 109,276 18% 128,946

1.7d No. 126,654 5,500 132,154 18% 155,942

1.7e No. 122,668 5,500 128,168 18% 151,238

1.7f No. 145,545 5,500 151,045 18% 178,233

1.7g No. 130,715 5,500 136,215 18% 160,734

1.7h No. 153,593 5,500 159,093 18% 187,730

1.8

1.8a No. 90,810 5,500 96,310 18% 113,646

1.8b No. 113,687 5,500 119,187 18% 140,641

1.8c No. 98,859 5,500 104,359 18% 123,144

1.8d No. 121,736 5,500 127,236 18% 150,138

1.8e No. 115,722 5,500 121,222 18% 143,042

1.8f No. 138,600 5,500 144,100 18% 170,038

1.8g No. 123,770 5,500 129,270 18% 152,539

1.8h No. 152,191 5,500 157,691 18% 186,075

1.9

1.9a No. 33,460 4,000 37,460 18% 44,203

1.9b No. 36,705 4,000 40,705 18% 48,032

4 pole, EDO with Thermal- Magnetic Release



1250A, 3 &4 Pole, ACB (Draw-out Type) with Thermal Magnetic / Microprocessor release (O / C, S / C & E / F) having breaking capacity Icu of 50kA at 415V with 6NO+6NC potential feee auxiliary contacts, secondary isolating contacts with all necessary Electro Mechanical protections & interlocks etc. ACB Module shall have enclosure dimension: 2000 (H) x 800 (W) x 1000 (D) & following technical features:






800A, 3 &4 Pole, ACB (Draw-out Type) with Thermal Magnetic / Microprocessor release (O / C, S / C & E / F) having breaking capacity Icu of 50kA at 415V with 6NO+6NC potential feee auxiliary contacts, secondary isolating contacts with all necessary Electro Mechanical protections & interlocks etc. ACB module shall have enclosure dimension: 2000 (H) x 800 (W) x 1000 (D) & following technical features.









Above 400A, upto & including 630A, 3 & 4 Pole, Air Break Fixed MCCB conforms to IS / IEC 60947-2 with trip free mechanism, current limiting type with Thermal Magnetic/ Microprocessor release (O / C, S / C & E / F) with adjustable settings & having minimum 2NO+2NC potential free auxiliary contacts with all necessary Electro Mechanical protections & interlocks etc. MCCB module, when used as Incommer/ Bus Coupler, shall have enclosure dimensions- 2000 (H) x 650 (W) x 600 (D) & following technical features:

3 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics =100% of Icu), TM release 3 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics =100% of Icu), Microprocessor release








1000A, 3 &4 Pole, ACB (Draw-out Type) with Thermal Magnetic / Microprocessor release (O / C, S / C & E / F) having breaking capacity Icu of 50kA at 415V with 6NO+6NC potential feee auxiliary contacts, secondary isolating contacts with all necessary Electro Mechanical protections & interlocks etc. ACB Module shall have enclosure dimension: 2000(H) x 800(W) x 1000 (D) & following technical features:





S.O.R. Mech 2019-20Page 117 of 166

Section- "E"


Rates inclusive of

GST




1.9c No. 31,984 4,000 35,984 18% 42,461

1.9d No. 34,701 4,000 38,701 18% 45,667

1.9e No. 31,984 4,000 35,984 18% 42,461

1.9f No. 34,701 4,000 38,701 18% 45,667

1.9g No. 40,609 4,000 44,609 18% 52,639

1.9h No. 46,940 4,000 50,940 18% 60,109

1.9i No. 38,017 4,000 42,017 18% 49,580

1.9j No. 42,685 4,000 46,685 18% 55,088

1.9k No. 38,017 4,000 42,017 18% 49,580

1.9l No. 42,685 4,000 46,685 18% 55,088

1.10

1.10a No. 33,460 4,000 37,460 18.00% 44,203

1.10b No. 36,705 4,000 40,705 18.00% 48,032

1.10c No. 31,984 4,000 35,984 18% 42,461

1.10d No. 34,701 4,000 38,701 18% 45,667

1.10e No. 31,984 4,000 35,984 18% 42,461

1.10f No. 34,701 4,000 38,701 18% 45,667

1.10g No. 40,609 4,000 44,609 18% 52,639

1.10h No. 46,940 4,000 50,940 18% 60,109

1.10i No. 38,017 4,000 42,017 18% 49,580

1.10j No. 42,685 4,000 46,685 18% 55,088

1.10k No. 38,017 4,000 42,017 18% 49,580

1.10l No. 42,685 4,000 46,685 18% 55,088

1.11

1.11a No. 29,145 4,000 33,145 18% 39,111

1.11b No. 33,434 4,000 37,434 18% 44,172

1.11c No. 26,969 4,000 30,969 18% 36,543

1.11d No. 32,345 4,000 36,345 18% 42,887

3 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics =100% of Icu), Microprocessor release


4 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics =100% of Icu), TM release





Above 250A, upto & including 400A, 3 / 4 Pole, Air Break Fixed MCCB conforms to IS/ IEC 60947-2 with trip free mechanism, current limiting type with Thermal Magnetic / Microprocessor release (O / C, S / C & E / F) with adjustable settings & having minimum 2NO+2NC potential free auxiliary contacts with all necessary Electro-Mechanical protections & interlocks etc. MCCB module, when used as Incommer/ Bus Coupler, shall have enclosure dimensions- 1800 (H) x 600 (W) x 600 (D) & following technical features:


Above 400A, upto & including 630A, 3 & 4 Pole, Air Break Fixed MCCB conforms to IS / IEC 60947-2 with trip free mechanism, current limiting type with Thermal Magnetic/ Microprocessor release (O / C, S / C & E / F) with adjustable settings & having minimum 2NO+2NC potential free auxiliary contacts with all necessary Electro-Mechanical protections & interlocks etc. MCCB module, when used as Outgoing(s), shall have enclosure dimensions- 600 (H) x 600 (W) x 600 (D) & following technical features:

















S.O.R. Mech 2019-20Page 118 of 166

Section- "E"


Rates inclusive of

GST




1.11e No. 26,969 4,000 30,969 18% 36,543

1.11f No. 32,345 4,000 36,345 18% 42,887

1.11g No. 34,380 4,000 38,380 18% 45,288

1.11h No. 39,690 4,000 43,690 18% 51,554

1.11i No. 31,690 4,000 35,690 18% 42,114

1.11j No. 37,729 4,000 41,729 18% 49,240

1.11k No. 31,690 4,000 35,690 18% 42,114

1.11l No. 37,729 4,000 41,729 18% 49,240

1.12

1.12a No. 29,145 3,500 32,645 18% 38,521

1.12b No. 33,434 3,500 36,934 18% 43,582

1.12c No. 26,969 3,500 30,469 18% 35,953

1.12d No. 32,345 3,500 35,845 18% 42,297

1.12e No. 26,969 3,500 30,469 18% 35,953

1.12f No. 32,345 3,500 35,845 18% 42,297

1.12g No. 34,380 3,500 37,880 18% 44,698

1.12h No. 39,690 3,500 43,190 18% 50,964

1.12i No. 31,690 3,500 35,190 18% 41,524

1.12j No. 37,729 3,500 41,229 18% 48,650

1.12k No. 31,690 3,500 35,190 18% 41,524

1.12l No. 37,729 3,500 41,229 18% 48,650

1.13

1.13a No. 24,830 3,500 28,330 18% 33,429

1.13b No. 27,688 3,500 31,188 18% 36,802

1.13c No. 23,370 3,500 26,870 18% 31,707

1.13d No. 26,346 3,500 29,846 18% 35,218

1.13e No. 21,246 3,500 24,746 18% 29,200







Above 250A, upto & including 400A, 3 & 4 Pole, Air Break Fixed MCCB conforms to IS/ IEC 60947-2 with trip free mechanism, current limiting type with Thermal Magnetic/ Microprocessor release (O / C, S / C & E / F) with adjustable settings & having minimum 2NO+2NC potential free auxiliary contacts with all necessary Electro-Mechanical protections & interlocks etc. MCCB module, when used as Outgoing(s), shall have enclosure dimensions- 500 (H) x 600 (W) x 600 (D) & following technical features:













Above 80A, upto & including 250A, 3 & 4 Pole, Air Break Fixed MCCB conforms to IS / IEC 60947-2 with trip free mechanism, current limiting type with Thermal-Magnetic / Microprocessor release (O / C, S / C & E / F) with adjustable settings & having minimum 2NO+2NC potential free auxiliary contacts with all necessary Electro-Mechanical protections & interlocks etc. MCCB module, when used as Incommer/ Bus Coupler, shall have enclosure dimensions- 1800(H) x 600(W) x 600 (D) & following technical features:







S.O.R. Mech 2019-20Page 119 of 166

Section- "E"


Rates inclusive of

GST




1.13f No. 26,346 3,500 29,846 18% 35,218

1.13g No. 28,641 3,500 32,141 18% 37,926

1.13h No. 32,923 3,500 36,423 18% 42,979

1.13i No. 26,645 3,500 30,145 18% 35,571

1.13j No. 31,894 3,500 35,394 18% 41,765

1.13k No. 24,863 3,500 28,363 18% 33,468

1.13l No. 31,894 3,500 35,394 18% 41,765

1.14

1.14a No. 24,830 3,500 28,330 18% 33,429

1.14b No. 27,688 3,500 31,188 18% 36,802

1.14c No. 23,370 3,500 26,870 18% 31,707

1.14d No. 26,346 3,500 29,846 18% 35,218

1.14e No. 21,246 3,500 24,746 18% 29,200

1.14f No. 26,346 3,500 29,846 18% 35,218

1.14g No. 28,641 3,500 32,141 18% 37,926

1.14h No. 32,923 3,500 36,423 18% 42,979

1.14i No. 26,645 3,500 30,145 18% 35,571

1.14j No. 31,894 3,500 35,394 18% 41,765

1.14k No. 24,863 3,500 28,363 18% 33,468

1.14l No. 31,894 3,500 35,394 18% 41,765

1.15

1.15a No. 14,110 3,500 17,610 18% 20,780

1.15b No. 21,935 3,500 25,435 18% 30,013

1.15c No. 12,046 3,500 15,546 18% 18,344

1.15d No. 20,281 3,500 23,781 18% 28,062

1.15e No. 11,715 3,500 15,215 18% 17,954








Above 80A, upto & including 250A, 3 & 4 Pole, Air Break Fixed MCCB conforms to IS/ IEC 60947-2 with trip free mechanism, current limiting type with Thermal Magnetic/ Microprocessor release (O / C, S / C & E / F) with adjustable settings & having minimum 2NO+2NC potential free auxiliary contacts with all necessary Electro-Mechanical protections & interlocks etc. MCCB module, when used as Outgoing(s), shall have enclosure dimensions- 400 (H) x 600 (W) x 600 (D) & following technical features:













Above 16A, upto & including 80A, 3 & 4 Pole, Air Break Fixed MCCB conforms to IS/ IEC 60947-2 with trip free mechanism, current limiting type with Thermal Magnetic/ Microprocessor release (O / C, S / C & E / F) with adjustable settings & having minimum 2NO+2NC potential free auxiliary contacts with all necessary Electro-Mechanical protections & interlocks etc. MCCB module, when used as Incommer/ Bus Coupler, shall have enclosure dimensions- 1800(H) x 500(W) x 600 (D) & following technical features:






S.O.R. Mech 2019-20Page 120 of 166

Section- "E"


Rates inclusive of

GST




1.15f No. 20,281 3,500 23,781 18% 28,062

1.15g No. 16,644 3,500 20,144 18% 23,770

1.15h No. 25,564 3,500 29,064 18% 34,296

1.15i No. 13,574 3,500 17,074 18% 20,147

1.15j No. 23,045 3,500 26,545 18% 31,323

1.15k No. 13,078 3,500 16,578 18% 19,562

1.15l No. 23,045 3,500 26,545 18% 31,323

1.16

1.16a No. 14,110 3,500 17,610 18.00% 20,780

1.16b No. 21,935 3,500 25,435 18% 30,013

1.16c No. 12,046 3,500 15,546 18% 18,344

1.16d No. 20,281 3,500 23,781 18% 28,062

1.16e No. 11,715 3,500 15,215 18% 17,954

1.16f No. 20,281 3,500 23,781 18% 28,062

1.16g No. 16,644 3,500 20,144 18% 23,770

1.16h No. 25,564 3,500 29,064 18% 34,296

1.16i No. 13,574 3,500 17,074 18% 20,147

1.16j No. 23,045 3,500 26,545 18% 31,323

1.16k No. 13,078 3,500 16,578 18% 19,562

1.16l No. 23,045 3,500 26,545 18% 31,323

1.17

1.17a No. 43,781 3,200 46,981 18% 55,438

1.17b No. 34,280 3,200 37,480 18% 44,226

1.17c No. 27,125 3,200 30,325 18% 35,784

1.17d No. 20,959 3,200 24,159 18% 28,508

1.17e No. 16,581 3,200 19,781 18% 23,342

1.17f No. 13,115 3,200 16,315 18% 19,252

1.17g No. 10,516 3,200 13,716 18% 16,185








Above 16A, upto & including 80A, 3 & 4 Pole, Air Break Fixed MCCB conforms to IS/ IEC 60947-2 with trip free mechanism, current limiting type with Thermal Magnetic / Microprocessor release (O / C, S / C & E / F) with adjustable settings & having minimum 2NO+2NC potential free auxiliary contacts with all necessary Electro-Mechanical protections & interlocks etc. MCCB module, when used as Outgoing(s), shall have enclosure dimensions- 300(H) x 500(W) x 600 (D) & following technical features:













Add for No Load Compansation KVAR banks (APP type) with detuned filters, MCCB, Power Contractor , Auto/ manual control with switching on delay timer, housed in lower most compartment of incomer/ buscoupler module(s). KVAR bank, selected based on kva rating of associated transformer(s), shall be of following capacity.

125 kVAR for 4000A Incomer- approx 5% kVAR of 2500 kVA Transformer rating

100 kVAR for 3200A Incomer- approx 5% kVAR of 2000 kVA Transformer rating

80 kVAR for 2500A Incomer - approx 5% kVAR of 1600 kVA Transformer rating

62.5 kVAR for 2000A Incomer- approx 5% kVAR of 1250 kVA Transformer rating



31.5 kVAR for 1000A Incomer - approx 5% kVAR of 630 kVA Transformer rating

S.O.R. Mech 2019-20Page 121 of 166

Section- "E"


Rates inclusive of

GST




1.17h No. 8,272 3,200 11,472 18% 13,537

1.17i No. 6,573 3,200 9,773 18% 11,532

1.17j No. 4,941 3,200 8,141 18% 9,606

1.17k No. 4,090 3,200 7,290 18% 8,602

1.17l No. 3,443 3,200 6,643 18% 7,839

1.17m No. 2,695 3,200 5,895 18% 6,956

1.17n No. 2,147 3,200 5,347 18% 6,309

1.17o No. 1,721 3,200 4,921 18% 5,807

1.17p No. 1,035 3,200 4,235 18% 4,997

1.18

1.18a No. 466 122 588 18% 694

1.18b No. 512 122 634 18% 748

1.18c No. 512 122 634 18% 748

1.18d No. 512 122 634 18% 748

1.18e No. 251 122 373 18% 440

1.18f No. 7,731 140 7,871 18% 9,288

1.18g No. 838 140 978 18% 1,154

1.18h No. 1,616 140 1,756 18% 2,072

1.18i No. 1,616 140 1,756 18% 2,072

1.18j No. 838 140 978 18% 1,154

1.18k No. 1,616 140 1,756 18% 2,072

1.18l No. 838 140 978 18% 1,154

1.18m No. 433 140 573 18% 676

1.18n No. 1,444 235 1,679 18% 1,981

1.19

1.19a No. 838 145 983 18% 1,160

1.19b No. 1,108 190 1,298 18% 1,532

1.19c No. 1,108 190 1,298 18% 1,532

25 kVAR for 800A Incomer- approx. 5% kVAR of 500 kVA Transformer rating



12.5 kVAR for 400A Incomer- approx 5% kVAR of 250 kVA Transformer rating

10 kVAR for 320A Incomer - approx 5% kVAR of 200 kVA Transformer rating.


6.25 KVAR for 200A Incomer- approx. 5% kVAR of 125 kVA Transformer rating


3 KVAR for 125A Incomer- approx. 5% kVAR of 63 kVA Transformer rating

Part-2

Add for providing indicating & measuring instruments complete with accessories, associated wiring & controls of following type & rating

R, Y & B Phase Indicating Lamps (63.5 / 110 / 230V AC) for Incoming module(s)

On/ Off/ Trip, spring charged , trip circuit healthy, Control Supply ON/ Healthy indicating lamps(24 / 110V DC or 110V AC) for ACB

controlled Incomming/ Buscoupler module(s).

On/ Off/ Trip, spring charged , trip circuit healthy indicating lamps (24-110V AC / DC) for ACB controlled Outgoing module(s).

On/ Off/ Trip, Control Supply ON/ Healthy Indicating lamps (24 / 110V DC or 110V AC) for MCCB controlled Incomming/ Buscoupler

module(s).

On/ Off/ Trip Indicating lamps(110 / 230V AC) for MCCB controlled Outgoing module(s).

3 Ph, 4Wire Multifunction Meter, Class 1.0 or better, Flush Mounting- 96 x 96 mm with RS 485 communication port for Incoming(s)/

Outgoings(s), as required.

AC Ameter, Analogue Type(96 x 96) & ASS for Incoming(s)/ Outgoings(s), as required.

AC Ameter, Analogue Type(144 x144) & ASS for Incoming(s)/ Outgoing(s), as required.

AC Ameter, Digital Type(96 x 96) with inbuilt ASS for Incoming(s)/ Outgoings(s), as required.

AC Voltmeter, Analogue Type(96 x 96) & VSS for Incoming(s)/ Outgoings(s), as required.

AC Voltmeter, Analogue Type(144 x 144) & VSS for Incoming(s)/ Outgoings(s), as required.

AC Volt meter, Digital Type(96 x 96) with inbuilt VSS for Incoming(s)/ Outgoings(s), as required.

Local/ Remote Selector Switch for ACB controlled Incommer/ Bus Coupler / Outgoings modules, as required.

TNC Switch for ACB controlled Incommer/ Bus Coupler / Outgoings modules, as required.

Add for providing instrument Transformers complete with accessories, associated wiring & controls, of following type & rating

Cast rasin insulated Current Transformer, Single Core with CTR 50-75/1A or 5A, 5-15VA, Class 1.0 or better for metering, as applicable

Resin Cast insulated Current Transformer, Double Core with CTR 50-75/1A or 5A, 5-15VA, Class 1.0 or better for metering/ 5P10 or better

for protection, as applicable

Resin Cast insulated Current Transformer, Single Core with CTR 100-150/1A or 5A, 5-15VA, Class 1.0 or better for metering, as applicable

S.O.R. Mech 2019-20Page 122 of 166

Section- "E"


Rates inclusive of

GST




1.19d No. 1,108 190 1,298 18% 1,532

1.19e No. 1,253 190 1,443 18% 1,703

1.19f No. 1,281 190 1,471 18% 1,736

1.19g No. 1,490 190 1,680 18% 1,982

1.19h No. 1,677 190 1,867 18% 2,203

1.19i No. 1,770 190 1,960 18% 2,313

1.19j No. 1,770 190 1,960 18% 2,313

1.19k No. 2,282 190 2,472 18% 2,917

1.19l No. 2,282 255 2,537 18% 2,994

1.19m No. 2,609 295 2,904 18% 3,427

1.19n No. 2,584 295 2,879 18% 3,397

1.19o No. 13,553 735 14,288 18% 16,860

1.19p No. 13,553 735 14,288 18% 16,860

1.20

1.20a No. 15,192 1,445 16,637 18% 19,632

1.20b No. 15,192 1,445 16,637 18% 19,632

1.20c No. 15,192 1,445 16,637 18% 19,632

1.20d No. 13,097 1,445 14,542 18% 17,160

1.20e No. 13,097 1,445 14,542 18% 17,160

1.20f No. 13,097 1,445 14,542 18% 17,160

1.20g No. 11,085 1,445 12,530 18% 14,785

1.20h No. 11,085 1,445 12,530 18% 14,785

1.20i No. 11,085 1,445 12,530 18% 14,785

1.20j No. 10,386 1,160 11,546 18% 13,624

1.20k No. 10,386 1,160 11,546 18% 13,624

Resin Cast insulated Current Transformer, Double Core with CTR 100-150/1A or 5A, 5-15VA, Class 1.0 / 5P10 for metering/ protection,

as applicable

Resin Cast insulated Current Transformer, Single Core with CTR 200-300/1A or 5A, 5-15VA, Class 1.0 for metering, as applicable

Resin Cast insulated Current Transformer, Double Core with CTR 200-300/1A or 5A, 5-15VA, Class 1.0 / 5P10 for metering/ protection,

as applicable

Resin Cast insulated Current Transformer, Single Core with CTR 400-1000/1A or 5A, 5-15VA, Class 1.0 / 5P10 for metering, as applicable

Resin Cast insulated Current Transformer, Double Core with CTR 400-1000/1A or 5A, 5-15VA, Class 1.0/ 5P10 for metering/ protection,

as applicable

Resin Cast insulated Current Transformer, Single Core with CTR 1200-1500/1A or 5A, 5-15VA, Class 1.0 / 5P10 for metering, as

applicable

Resin Cast insulated Current Transformer, Double Core with CTR 1200-1500/1A or 5A, 5-15VA, Class 1.0 / 5P10 for metering/

protection, as applicable

Resin Cast insulated Current Transformer, Single Core with CTR 1600- 3000/1A or 5A, 5-15VA, Class 1.0 / 5P10 for metering, as

applicable



Resin Cast insulated Current Transformer, Single Core with CTR 3200- 4000/1A or 5A, 5-15VA, Class 1.0 / 5P10 for metering, as

applicable



Resin Cast insulated Voltage Transformer, Single Core with PTR 415/ root3/ 110/ root3, 50VA, Class 1.0 or better for metering, as

applicableResin Cast insulated Voltage Transformer, Double Core with PTR 415/ root3/ 110V/ root3/ 110V/ root3, 50 VA, Class 1.0 or better for

metering / 3P for protection, as applicabke

Add for providing LT Single Phase Control Transformers(Tape wound, dry type, low reactance with good regulation at short time loads to provide control suppply voltages for control circuits of AC Motor Starters and/ or auxiliary euipment not intended for direct connection to the main circuit) complete with accessories, associated wiring & controls, of following type & rating

3500 VA , 415 / 240V AC with Tapping ± 5% insteps of 2.5%











S.O.R. Mech 2019-20Page 123 of 166

Section- "E"


Rates inclusive of

GST




1.20l No. 10,386 1,160 11,546 18% 13,624

1.20m No. 8,803 1,160 9,963 18% 11,756

1.20n No. 8,803 1,160 9,963 18% 11,756

1.20o No. 8,803 1,160 9,963 18% 11,756

1.20p No. 6,055 1,160 7,215 18% 8,514

1.20q No. 6,055 1,160 7,215 18% 8,514

1.20r No. 6,055 1,160 7,215 18% 8,514

1.20s No. 4,634 755 5,389 18% 6,359

1.20t No. 4,634 755 5,389 18% 6,359

1.20u No. 4,634 755 5,389 18% 6,359

1.20v No. 4,472 755 5,227 18% 6,168

1.20w No. 4,100 755 4,855 18% 5,729

1.20x No. 3,690 755 4,445 18% 5,245

1.20y No. 3,866 755 4,621 18% 5,453

1.20z No. 3,479 755 4,234 18% 4,996

1.20aa No. 3,131 530 3,661 18% 4,320 1.20ab No. 3,261 530 3,791 18% 4,473 1.20ac No. 3,060 530 3,590 18% 4,236 1.20ad No. 2,754 530 3,284 18% 3,875 1.20ae No. 2,980 530 3,510 18% 4,142 1.20af No. 2,809 530 3,339 18% 3,940 1.20ag No. 2,527 530 3,057 18% 3,607 1.20ah No. 2,766 530 3,296 18% 3,889 1.20ai No. 2,490 530 3,020 18% 3,564

1.20aj No. 2,241 530 2,771 18% 3,270

1.20ak No. 2,515 530 3,045 18% 3,593

1.20al No. 2,264 530 2,794 18% 3,297

1.20am No. 2,037 530 2,567 18% 3,029 1.20an No. 2,096 510 2,606 18% 3,075 1.20ao No. 2,096 510 2,606 18% 3,075

1.20ap No. 1,886 510 2,396 18% 2,827

1.20aq No. 1,770 510 2,280 18% 2,690

1.20ar No. 1,593 510 2,103 18% 2,482

1.20as No. 1,434 510 1,944 18% 2,294

1.20at No. 1,285 510 1,795 18% 2,118

1.20au No. 1,285 510 1,795 18% 2,118

1.20av No. 1,216 510 1,726 18% 2,037

46

46.1

a No 335,340 18,180 353,520 18% 417,154
















500 VA , 415 / 24V AC with Tapping ± 5% insteps of 2.5%400 VA , 415 / 240V AC with Tapping ± 5% insteps of 2.5%400 VA , 415 / 110V AC with Tapping ± 5% insteps of 2.5%400 VA , 415 / 24V AC with Tapping ± 5% insteps of 2.5%350 VA , 415 / 240V AC with Tapping ± 5% insteps of 2.5%350 VA , 415 / 110V AC with Tapping ± 5% insteps of 2.5%350 VA , 415 / 24V AC with Tapping ± 5% insteps of 2.5%300 VA , 415 / 240V AC with Tapping ± 5% insteps of 2.5%300 VA , 415 / 110V AC with Tapping ± 5% insteps of 2.5%




250 VA , 415 / 24V AC with Tapping ± 5% insteps of 2.5%200 VA , 415 / 240V AC with Tapping ± 5% insteps of 2.5%200 VA , 415 / 110V AC with Tapping ± 5% insteps of 2.5%








HFSR (Harmonic Free Series Reactor) soft starter

Supply, installation, testing & commissioning HFSR (Harmonic Free Series Reactor) HV soft starter panel suitable for 3-phase squirrel cage induction motor & provided with built in bypass terminal for pump control application by torque control method as per tender specification.Soft Starter shall be operated on 3-phase, 50 Hz, fault Level 3KA for 1Sec., with Copper bus bar & enclosure fabricated from 2mm CRCA sheet steel, solidly earthed neutral system earthing complete with following associated necessary equipments & accessories.

Voltage level (KV) & KW Rating Line Side HFSR Soft Starter

3.3/6.6 315

S.O.R. Mech 2019-20Page 124 of 166

Section- "E"


Rates inclusive of

GST




b No 344,655 18,180 362,835 18% 428,145

c No 353,970 18,180 372,150 18% 439,137

d No 363,285 18,180 381,465 18% 450,129

372,600 18,180 390,780 18% 461,120

463,887 18,180 482,067 18% 568,839

381,915 18,180 400,095 18% 472,112

470,408 18,180 488,588 18% 576,534

395,888 18,180 414,068 18% 488,600

484,380 18,180 502,560 18% 593,021

395,888 18,180 414,068 18% 488,600

484,380 18,180 502,560 18% 593,021

400,545 18,180 418,725 18% 494,096

503,010 18,180 521,190 18% 615,004

400,545 18,180 418,725 18% 494,096

503,010 18,180 521,190 18% 615,004

405,203 18,180 423,383 18% 499,592

512,325 18,180 530,505 18% 625,996

405,203 18,180 423,383 18% 499,592

512,325 18,180 530,505 18% 625,996

409,860 18,180 428,040 18% 505,087

516,983 18,180 535,163 18% 631,492

409,860 18,180 428,040 18% 505,087

516,983 18,180 535,163 18% 631,492

419,175 18,180 437,355 18% 516,079

521,640 18,180 539,820 18% 636,988

46.2

a No 307,395 18,180 325,575 18% 384,179

b No 316,710 18,180 334,890 18% 395,170

c No 326,025 18,180 344,205 18% 406,162

d No 335,340 18,180 353,520 18% 417,154

344,655 18,180 362,835 18% 428,145

435,942 18,180 454,122 18% 535,864

353,970 18,180 372,150 18% 439,137

442,463 18,180 460,643 18% 543,559

367,943 18,180 386,123 18% 455,625

456,435 18,180 474,615 18% 560,046

367,943 18,180 386,123 18% 455,625

456,435 18,180 474,615 18% 560,046

372,600 18,180 390,780 18% 461,120

475,065 18,180 493,245 18% 582,029

400

3.3/6.6 450

e 3.3/6.6 500 No

11

f 3.3/6.6 560 No

11

g 3.3/6.6 600 No

11

h 3.3/6.6 650 No

11

i 3.3/6.6 710 No

11

j 3.3/6.6 750 No

11

k 3.3/6.6 800 No

11

l 3.3/6.6 850 No

11

m 3.3/6.6 900 No

11

n 3.3/6.6 950 No

11

o 3.3/6.6 1000 No

11

Neutral Side HFSR Soft Starter

3.3/6.6 315

3.3/6.6 355

3.3/6.6 400

e 3.3/6.6 500 No

11

Voltage level (KV) & KW Rating

3.3/6.6 450

f 3.3/6.6 560 No

11

g 3.3/6.6 600 No

11

h 3.3/6.6 650 No

11

i 3.3/6.6 710 No

11

3.3/6.6 355

3.3/6.6

S.O.R. Mech 2019-20Page 125 of 166

Section- "E"


Rates inclusive of

GST




372,600 18,180 390,780 18% 461,120

475,065 18,180 493,245 18% 582,029

377,258 18,180 395,438 18% 466,617

484,380 18,180 502,560 18% 593,021

377,258 18,180 395,438 18% 466,617

484,380 18,180 502,560 18% 593,021

381,915 18,180 400,095 18% 472,112

489,038 18,180 507,218 18% 598,517

381,915 18,180 400,095 18% 472,112

489,038 18,180 507,218 18% 598,517

391,230 18,180 409,410 18% 483,104

493,695 18,180 511,875 18% 604,013

47

47.1

3.3 462,645 18,180 480,825 18% 567,374

6.6 465,750 18,180 483,930 18% 571,037

11 522,675 18,180 540,855 18% 638,209

b 3.3 462,645 18,180 480,825 18% 567,374

6.6 465,750 18,180 483,930 18% 571,037

11 527,850 18,180 546,030 18% 644,315

3.3 485,415 18,180 503,595 18% 594,242

6.6 476,100 18,180 494,280 18% 583,250

11 533,025 18,180 551,205 18% 650,422

3.3 485,415 18,180 503,595 18% 594,242

6.6 476,100 18,180 494,280 18% 583,250

11 538,200 18,180 556,380 18% 656,528

3.3 486,450 18,180 504,630 18% 595,463

6.6 507,150 18,180 525,330 18% 619,889

11 538,200 18,180 556,380 18% 656,528

3.3 500,940 18,180 519,120 18% 612,562

6.6 507,150 18,180 525,330 18% 619,889

11 538,200 18,180 556,380 18% 656,528

3.3 550,620 18,180 568,800 18% 671,184

6.6 556,830 18,180 575,010 18% 678,512

11 548,550 18,180 566,730 18% 668,741

3.3 584,775 18,180 602,955 18% 711,487

6.6 556,830 18,180 575,010 18% 678,512

11 569,250 18,180 587,430 18% 693,167

j 3.3/6.6 750 No

11

k 3.3/6.6 800 No

11

l 3.3/6.6 850 No

11

m 3.3/6.6 900 No

11

n 3.3/6.6 950 No

11

o 3.3/6.6 1000 No

11

Flux Compensated Magnetic Amplifier (FCMA) Soft Starter

Supply, installation, testing & commissioning FCMA (Flux compensated magnetic amplifier) HV soft starter panel suitable for 3-phase squirrel cage induction motor & provided with built in bypass terminal for pump control application by torque control method as per tender specification.Soft Starter shall be operated on 3-phase, 50 Hz, fault Level 3KA for 1Sec., with Copper bus bar & enclosure fabricated from 2mm CRCA sheet steel, solidly earthed neutral system earthing complete with following associated necessary equipments & accessories.

Voltage level (KV) & KW Rating

Line Side FCMA Soft Starter

a 315 KW No

No

355 KW

No

c 400 KW No

No

d 450 KW

No

e 500 KW No

No

f 560 KW

No

g 630 KW No

No

h 710 KW

No

S.O.R. Mech 2019-20Page 126 of 166

Section- "E"


Rates inclusive of

GST




3.3 588,915 18,180 607,095 18% 716,372

6.6 593,055 18,180 611,235 18% 721,257

11 569,250 18,180 587,430 18% 693,167

3.3 595,125 18,180 613,305 18% 723,700

6.6 593,055 18,180 611,235 18% 721,257

11 579,600 18,180 597,780 18% 705,380

3.3 602,370 18,180 620,550 18% 732,249

6.6 593,055 18,180 611,235 18% 721,257

11 595,125 18,180 613,305 18% 723,700

3.3 609,615 18,180 627,795 18% 740,798

6.6 621,000 18,180 639,180 18% 754,232

11 631,350 18,180 649,530 18% 766,445

3.3 615,825 18,180 634,005 18% 748,126

6.6 621,000 18,180 639,180 18% 754,232

11 641,700 18,180 659,880 18% 778,658

3.3 642,735 18,180 660,915 18% 779,880

6.6 639,630 18,180 657,810 18% 776,216

11 683,100 18,180 701,280 18% 827,510

3.3 666,540 18,180 684,720 18% 807,970

6.6 683,100 18,180 701,280 18% 827,510

11 714,150 18,180 732,330 18% 864,149

3.3 667,575 18,180 685,755 18% 809,191

6.6 695,520 18,180 713,700 18% 842,166

11 724,500 18,180 742,680 18% 876,362

47.2

3.3 429,525 18,180 447,705 18% 528,292

6.6 434,700 18,180 452,880 18% 534,398

11 465,750 18,180 483,930 18% 571,037

3.3 429,525 18,180 447,705 18% 528,292

6.6 No 434,700 18,180 452,880 18% 534,398

11 465,750 18,180 483,930 18% 571,037

3.3 450,225 18,180 468,405 18% 552,718

6.6 445,050 18,180 463,230 18% 546,611

11 481,275 18,180 499,455 18% 589,357

3.3 450,225 18,180 468,405 18% 552,718

6.6 445,050 18,180 463,230 18% 546,611

11 481,275 18,180 499,455 18% 589,357

3.3 453,330 18,180 471,510 18% 556,382

6.6 476,100 18,180 494,280 18% 583,250

11 507,150 18,180 525,330 18% 619,889

i 800 KW No

No

j 900 KW

No

k 1000 KW No

No

l 1120 KW

No

m 1250 KW No

No

n 1400 KW

No

o 1500 KW No

No

p 1600 KW

No

Voltage level (KV) & KW Rating Neutral Side FCMA Soft Starter

a 315 KW No

No

b 355 KW

c 400 KW No

No

d 450 KW

No

e 500 KW No

No

S.O.R. Mech 2019-20Page 127 of 166

Section- "E"


Rates inclusive of

GST




3.3 465,750 18,180 483,930 18% 571,037

6.6 476,100 18,180 494,280 18% 583,250

11 507,150 18,180 525,330 18% 619,889

3.3 507,150 18,180 525,330 18% 619,889

6.6 507,150 18,180 525,330 18% 619,889

11 527,850 18,180 546,030 18% 644,315

3.3 543,375 18,180 561,555 18% 662,635

6.6 524,745 18,180 542,925 18% 640,652

11 548,550 18,180 566,730 18% 668,741

3.3 555,795 18,180 573,975 18% 677,291

6.6 560,970 18,180 579,150 18% 683,397

11 548,550 18,180 566,730 18% 668,741

3.3 560,970 18,180 579,150 18% 683,397

6.6 560,970 18,180 579,150 18% 683,397

11 558,900 18,180 577,080 18% 680,954

3.3 569,250 18,180 587,430 18% 693,167

6.6 560,970 18,180 579,150 18% 683,397

11 569,250 18,180 587,430 18% 693,167

3.3 574,425 18,180 592,605 18% 699,274

6.6 584,775 18,180 602,955 18% 711,487

11 610,650 18,180 628,830 18% 742,019

3.3 584,775 18,180 602,955 18% 711,487

6.6 584,775 18,180 602,955 18% 711,487

11 621,000 18,180 639,180 18% 754,232

3.3 611,685 18,180 629,865 18% 743,241

6.6 607,545 18,180 625,725 18% 738,356

11 662,400 18,180 680,580 18% 803,084

3.3 634,455 18,180 652,635 18% 770,109

6.6 654,120 18,180 672,300 18% 793,314

11 693,450 18,180 711,630 18% 839,723

3.3 636,525 18,180 654,705 18% 772,552

6.6 662,400 18,180 680,580 18% 803,084

11 703,800 18,180 721,980 18% 851,936

48

1 No 745,200 22,220 767,420 18% 905,556

2 No 605,475 22,220 627,695 18% 740,680

f 560 KW

No

g 630 KW No

No

h 710 KW

No

i 800 KW No

No

j 900 KW

No

1400 KW

No

k 1000 KW No

No

l 1120 KW

No

No

No

p 1600 KW

No

m 1250 KW No

No

n

o 1500 KW

Supply, Installation, testing & commissioning Indoor type 11 KV, 630 Amp., 21kA for 3 sec. SF6 type extensible and motorized 4 way smart Ring Main Unit (RMU) complete with (2 VCB + 2 LBS) with FRTU and FPI with IP Protection, as per IS

11kV Ring Main Unit (RMU)


S.O.R. Mech 2019-20Page 128 of 166

Section- "E"


Rates inclusive of

GST




3 No 465,750 22,220 487,970 18% 575,805

4 No 605,475 22,220 627,695 18% 740,680

5 No 326,025 22,220 348,245 18% 410,929

6 No 419,175 22,220 441,395 18% 520,846

7 No 773,145 22,220 795,365 18% 938,531

8 No 698,625 22,220 720,845 18% 850,597

9 No 698,625 22,220 720,845 18% 850,597

10 No 512,325 22,220 534,545 18% 630,763

11 No 344,655 22,220 366,875 18% 432,913

12 No 419,175 22,220 441,395 18% 520,846

49

2 No 52,981 233 53,214 18.0% 62,793

3 No 61,346 303 61,649 18% 72,746

4 No 69,148 464 69,612 18% 82,142

5 No 90,553 698 91,251 18% 107,676


Supply, Installation, testing & commissioning Outdoor type 11 KV, 630 Amp., 21kA for 3 sec. SF6 type non extensible and motorized 5 way smart Ring Main Unit (RMU) complete with (2 VCB + 3 LBS) with FRTU and FPI with IP Protection, as per IS

Supply, Installation, testing & commissioning Outdoor type 11 KV, 630 Amp., 21kA for 3 sec. SF6 type extensible and motorized 4 way smart Ring Main Unit (RMU) complete with (2 VCB + 2 LBS) with FRTU and FPI with IP Protection, as per IS

5 kVA Air Cooled

7.5 kVA Air Cooled

10 kVA Air Cooled


Supply, Installation, testing & commissioning Indoor type 11 KV, 630 Amp., 21kA for 3 sec. SF6 type extensible and motorized 3 way smart Ring Main Unit (RMU) complete with (3 VCB) with FRTU and FPI with IP Protection, as per IS

Supply, Installation, testing & commissioning Indoor type 11 KV, 630 Amp., 21kA for 3 sec. SF6 type extensible and motorized one way smart Ring Main Unit (RMU) complete with LB and with FPI with IP Protection, as per IS

Supply, Installation, testing & commissioning Outdoor type 11 KV, 630 Amp., 21kA for 3 sec. SF6 type extensible and motorized 3 way smart Ring Main Unit (RMU) complete with (3 VCB) with FRTU and FPI with IP Protection, as per IS

Supply, Installation, testing & commissioning Outdoor type 11 KV, 630 Amp., 21kA for 3 sec. SF6 type extensible and motorized 3 way smart Ring Main Unit (RMU) complete with (1 VCB + 2 LBS) with FRTU and FPI with IP Protection, as per IS

Supply, Installation, testing & commissioning Outdoor type 11 KV, 630 Amp. 21kA for 3 sec. SF6 type extensible and motorized one way smart Ring Main Unit (RMU) complete with LB and with FPI with IP Protection, as per IS

Supply, Installation, testing & commissioning Outdoor type 11 KV, 630 Amp., 21kA for 3 sec. SF6 type extensible and motorized one way smart Ring Main Unit (RMU) complete with VCB and FPI with IP Protection, as per IS

Providing, erecting Servo Controlled Automatic Voltage stabilizer suitable for out put voltage of 415 Volt +/-1%, 3 Ph, 50 Hz, with copper wound transformer (air/oil cooled) as mentioned below. The stabilizer shall function satisfactorily even if incoming supply is unbalanced between phases within range of 10%. The stabilizer should be constructed in cubical box, with bi-directional wheels for easy handling, necessary monitors and user's controls on front panel suchas indication, alarm, volt meter and selector switch for measuring input and out put voltage, Auto/Manual selector switch, Raise/Low push buttons etc. Suitable capacity termination strips and bus bars for incoming and out going cable should be provided. All three phases shall be independently monitored and corrected. Following protections and indications shall be incorporatedOver Voltage / Under Voltage, Single Phasing,Cut off contactor with electronic output sensing unitServo Controlled Automatic Voltage Stabilizer (Out put 415 +/-1%)Input 220 to 460 Volt

3 kVA Air Cooled

Servo Controlled Automatic Voltage Stabilizer

S.O.R. Mech 2019-20Page 129 of 166

Section- "E"


Rates inclusive of

GST




6 No 99,535 929 100,464 18% 118,548

7 No 108,516 929 109,445 18% 129,145

8 No 118,192 1,159 119,351 18% 140,834

9 No 130,078 1,392 131,470 18% 155,135

10 No 158,175 1,624 159,799 18% 188,563

11 No 173,564 1,855 175,419 18% 206,994

12 No 234,622 1,855 236,477 18% 279,043

13 No 284,452 1,855 286,307 18% 337,842

14 No 297,443 1,855 299,298 18% 353,172

15 No 335,170 2,550 337,720 18% 398,510

16 No 416,346 3,018 419,364 18% 494,850

60 kVA Air Cooled

75 kVA Air Cooled

100 kVA Air Cooled

125 kVA Air Cooled

12.5 kVA Air Cooled

50 kVA Air Cooled

15 kVA Air Cooled

20 kVA Air Cooled

25 kVA Air Cooled

30 kVA Air Cooled

40 kVA Air Cooled

S.O.R. Mech 2019-20Page 130 of 166

Section- "F"


1 2 3 7 8 9 101

I

II

1A

1 25mm Nominal Bore No 50,000 7,908 57,908 18% 68,331















1B

1C

2


Flow Meter/ Sensor:

DC pulsed type, IP 68 Protection, Flanged process connection as per IS 1538 or equivalent standard, SS304/ Metallic Alloy Flow Tube, SS316/ SS 316 L/ Hastelloy Sensor, SS316/ Hastelloy Grounding Ring/ Inbuilt Grounding Electrode, Neoprene/Polyurethane/ Hard Rubber/ Rilsan lining, SS304/ Die Cast Aluminium/ Carbon steel with Anticorrosive Paint Coil Housing with Junction Box, CS flanges.

Flow Transmitter/ Converter ( Remote Field Mounted):

Full Bore Electromagnetic Flow Meter- Inbuilt Battery Power operated



Rates exclusive of GST Totalwith GST

Design, Supply, Installation, Testing, Commissioning of Full Bore Electromagnetic flow meter with factory calibration, Inbuilt Battery Power Operated, flanged connection, Flow sensor, Indicator, transmitter and totaliser with all accessories viz. surge arrestor, associated cables, cabinets, hardwares, etc complete as per following specifications:

Microprocessor based, Modular design, 2 line LCD for indication of actual flow rate, forward, reverse, sum totaliser display, ±0.5% accuracy at 0.3 to 4 m/sec velocity, one scalable pulse/ one status, one Modbus output, one GPRS/ GSM output, IP 67 protection, Die cast aluminium/ polycarbonate/ SS316 with Anticorrosive Paint/ PU finish with glass window enclosure, Inbuilt EEPROM and Data Logger, 20 meters cable length for sensor to transmitter communication, Minimum 5 years battery lifetime, 3.6 VDC Non Rechargeable Lithium-thionyl chloride/ Ni-Cd high power batteries, Hourly Basis Worldwide transmission of measured data and events via e‐mail and SMS by integrated GSM/GPRS modem, Reliable data storage facility through integrated SD card etc alongwith wall mounted/ stand mounted cabinet.

Full Bore Electromagnetic Flow Meter (Inbuilt Battery Power Operated)- PN 10

Full Bore Electromagnetic Flow Meter (Inbuilt Battery Power Operated)- PN 16. For PN 16 rating, 10% rise in rate to be considere on rate of PN 10 rating Item (Item No. 1A)

Full Bore Electromagnetic Flow Meter (Inbuilt Battery Power Operated)- PN 25For PN 25 rating, 15% rise in rate to be considere on rate of PN 10 rating Item (Item No. 1A)Full Bore Electromagnetic Flow Meter- Regular Power operated

Design, Supply, Installation, Testing, Commissioning of Full Bore Electromagnetic flow meter with factory calibrated, Regular Power Operated, flanged connection, Flow sensor, Indicator, transmitter and totaliser with all accessories viz. surge arrestor, associated cables, cabinets, hardwares, etc complete as per following specifications:

S.O.R. Mech 2019-20Page 131 of 166

Section- "F"






I

II

2A

























Flow Meter/ Sensor:

DC pulsed type, IP 68 Protection, Flanged process connection as per IS 1538 or equivalent standard, SS304/ Metallic Alloy Flow Tube, SS316/ SS 316 L/ Hastelloy Sensor, SS316/ Hastelloy Grounding Ring/ Inbuilt Grounding Electrode, Neoprene/ Polyurethane/ Hard Rubber/ Rilsan lining, SS304/ Die Cast Aluminium/ Carbon steel with Anticorrosive Paint Coil Housing with Junction Box, CS flanges.


Microprocessor based, Modular design, 2 line LCD for indication of actual flow rate, forward, reverse, sum totaliser display, ±0.5% accuracy at 0.3 to 4 m/sec velocity, 4 to 20 mA with HART/Modbus output, one scalable pulse, one status output, IP 67 protection, Die cast aluminium/ polycarbonate/ SS316 with Anticorrosive Paint/ PU finish with glass window enclosure, Inbuilt EEPROM and Data Logger, 20 meters cable length for sensor to transmitter communication etc alongwith wall mounted/ stand mounted cabinet.

Full Bore Electromagnetic Flow Meter (Regular Power Operated)- PN 10

S.O.R. Mech 2019-20Page 132 of 166

Section- "F"









28 1700mm Nominal Bore No 829,629 39,100 868,729 18% 1,025,100



31 2000mm Nominal Bore No 976,034 46,000 1,022,034 18% 1,206,000

32 2100mm Nominal Bore No 1,024,836 48,300 1,073,136 18% 1,266,300




2B

2C

3

I

II

3A Dual Path ( 4 Nos Insertion Sensor)- for pipe size ≥ 600 mm & ≤ 800 mm

No 488,700 20,000 508,700 18% 600,266

3B Four Path ( 8 Nos Insertion Sensor) - for pipe size > 800 mm & ≤ 4000 mm

No 705,271 46,000 751,271 18% 886,500

4

I

II

Full Bore Electromagnetic Flow Meter (Regular Power Operated)- PN 16For PN 16 rating, 10% rise in rate to be considere on rate of PN 10 rating Item (Item No. 2A)Full Bore Electromagnetic Flow Meter (Regular Power Operated)- PN 25For PN 25 rating, 15% rise in rate to be considere on rate of PN 10 rating Item (Item No. 2A)Insertion Type Ultrasonic Flow Meter

Design, Supply, Installation, Testing, Commissioning of Single/ Dual/ Four Path Insertion Ultrasonic flow meter working on transit time principle, with factory calibrated and site verification, Regular Power Operated, Flow sensor, Indicator, transmitter and totaliser with all accessories viz. surge arrestor, associated cables, cabinets, hardwares, etc complete as per following specifications:

Flow Meter/ Sensor:

2/ 4/ 8 nos insertion ultrasonic type sensor ( 1/ 2/ 4 Pair) with ball valve for online removal of sensors/ any other interaction/ retraction assembly, PN 16 pressure rating, SS 316 Sensor MOC, IP 68 Protection.


Microprocessor based, Modular design, 2 line LCD for indication of actual flow rate, forward, reverse, sum totaliser display, ±1% accuracy at 0.3 to 4 m/sec velocity, 4 to 20 mA with HART, one scalable pulse output, IP 65/ 67 protection, Die cast aluminum/ polycarbonate/ SS316 with Anticorrosive Paint/ PU finish with glass window enclosure, Inbuilt EEPROM and Data Logger,20 meters cable length for sensor to transmitter communication.

Clamp On Ultrasonic Flow Meter- Fixed Type

Design, Supply, Installation, Testing, Commissioning of Fixed Type, Single Path Clamp On Ultrasonic flow meter working on transit time principle, with factory calibrated and site verification, Regular Power Operated, Flow sensor, Indicator, transmitter and totaliser with all accessories viz. surge arrestor, associated cabled, cabinets, hardwares, etc complete as per following specifications:

Flow Meter/ Sensor:

2 nos magnetic clamp on ultrasonic type sensor ( 1 Pair) with SS belt according to pipe size and necessary fitting assembly, ABS/ Alluminium Alloy Sensor MOC, IP 68 Protection.


S.O.R. Mech 2019-20Page 133 of 166

Section- "F"






4A for pipe size 15 TO 80 mm No 178,295 14,874 193,169 18% 227,939

4B for pipe size 100 TO 700 mm No 182,832 15,253 198,085 18% 233,740

4C for pipe size 750 TO 4000 mm No 185,047 15,438 200,485 18% 236,572

5

I

II

5A for pipe size 15 TO 80 mm No 161,415 13,466 174,881 18% 206,360

5B for pipe size 100 TO 700 mm No 165,952 13,845 179,797 18% 212,160

5C for pipe size 750 TO 4000 mm No 168,167 14,030 182,197 18% 214,992

6

I

II

6A Canal Depth 3- 5 Meter and width 5 - 10 meter

No 1,002,250 83,614 1,085,864 18% 1,281,320

6B Canal Depth 3- 20 Meter and width 20 - 25 meter

No 1,126,740 94,000 1,220,740 18% 1,440,473

7

Microprocessor based, Modular design, 2 line LCD for indication of actual flow rate, forward, reverse, sum totaliser display, ±1% accuracy at 0.3 to 4 m/sec velocity, 4 to 20 mA with HART, one scalable pulse output, IP 65/ 67 protection, Die cast aluminum/ polycarbonate/ SS316 with Anticorrosive Paint/ PU finish with glass window enclosure, Inbuilt EEPROM and Data Logger,20 meters cable length for sensor to transmitter communication.

Clamp On Ultrasonic Flow Meter- Portable Type

Design, Supply, Installation, Testing, Commissioning of Portable Type, Single Path Clamp On Ultrasonic flow meter working on transit time principle, with site verification, Inbuilt Battery Power Operated, Flow sensor and Hand Held Indicator with all accessories viz. battery charger, associated cabled, portable case, hardwares, etc complete as per following specifications:

Flow Meter/ Sensor:2 nos magnetic clamp on ultrasonic type sensor ( 1 Pair) with SS belt according to pipe size and necessary fitting assembly, ABS/ Alluminium Alloy Sensor MOC, IP 68 Protection.

Flow Indicator/ Converter ( Hand Held):Microprocessor based, Modular design, minimum 2 line LCD for indication of actual flow rate, forward, reverse, sum totaliser display, ±1% accuracy at 0.3 to 4 m/sec velocity,RS 232 output, IP 65/ 67 protection, Die cast aluminum/ polycarbonate/ SS316 with Anticorrosive Paint/ PU finish with glass window enclosure.20 meters cable length for sensor to transmitter communication.

Acoustic Doppler Type Flow Meter- Regular Power Operated

Design, Supply, Installation, Testing, Commissioning of Accoustic Doppler Type flow meter, working on transit time principle, with site verification, Regular Power Operated, Flow sensor with Mounting Stand, Indicator, Transmitter and totalizer with all accessories viz. associated cabled, cabinets, hardwares, etc complete as per following specifications:Flow Meter/ Sensor:Accoustic Doppler type Flow Meter with real time acoustic doppler current meter with RS232/serial digital interface(SDI)-12 interface, features programmable range selection, vertical acoustic beam for water level measurement, multi cell current profiling, integrated temperature sensor, pressure sensor, memory storage an mounting stand.

Flow Indicator/ Converter ( Hand Held):Microprocessor based, Modular design, Regular power Operated, minimum 2 line LCD for indication of actual flow rate, forward, reverse, sum totaliser display, ±1% accuracy at 0.3 to 4 m/sec velocity,One current(4-20mA) with HART output, one scalable pulse, one status output, RS 232 output, IP 65/ 67 protection, Die cast aluminum/ polycarbonate/ SS316 with Anticorrosive Paint/ PU finish with glass window enclosure, Inbuilt EEPROM and Data Logger,20 meters cable length for sensor to transmitter communication.Instrument shall have facility to connect with GPRS/ VHF/ VSAT modem.

Water Meters (Multijet/ Woltman Type):

S.O.R. Mech 2019-20Page 134 of 166

Section- "F"






7.1

a 15 mm No 1,425 119 1,544 18% 1,822

b 20 mm No 1,636 136 1,772 18% 2,091

c 25 mm No 5,824 486 6,310 18% 7,446

d 40 mm No 8,704 726 9,430 18% 11,127

7.2

a 15 mm No 5,117 427 5,544 18% 6,542

b 20 mm No 5,328 444 5,772 18% 6,811

c 25 mm No 9,516 794 10,310 18% 12,166

d 40 mm No 12,397 1,034 13,431 18% 15,849

METER READING DEVICE/ Hand Held Unit No 121,325 - 121,325 18% 143,164

AMR Module- for upgradation of AMR Compatible Meter For 15 mm to 300 mm size

No 3,693 308 4,001 18% 4,721

7.5 Data Hosting Charges per Meter Per Annum ( For Calculation of O&M Charges)

Per Meter Per

Year

- 90 90 18% 106

7.3

7.4

Horizontal Inferential Multijet Type Water Meter- AMR Compatible:Design, Supply, Installation, Testing, Commissioning of Horizontal Inferential Multijet Type Water Meter, Brass/ Bronze body material, totalizer made of copper can/ suitable anti corrosive metallic material, totaliser metalic shall have 5 mm thick glass cover suitable against antifraud attempts, Thread End process connection, IP 68 protection class, AMR Compatible Water Meter, Dry dial, magnetically coupled, water meters complete with tubular strainer, brass nuts and nipples, ISO 4064 : 2005 with valid CE mark or ISI mark, mentioning notified body number along with MlD / OIML / ISO certification from a recognized International laboratory.The Totalizer should have facility to externally mount wireless AMR communication module without opening the meter for upgradation to AMR in future.

Horizontal Inferential Multijet Type Water Meter- AMR Based: Water Meter:Design, Supply, Installation, Testing, Commissioning of Horizontal Inferential Multijet Type Water Meter, Brass/ Bronze body material, totalizer made of copper can/ suitable anti corrosive metallic material, totaliser metalic shall have 5 mm thick glass cover suitable against antifraud attempts, Thread End process connection, IP 68 protection class, AMR Water Meter, Dry dial, magnetically coupled, water meters complete with tubular strainer, brass nuts and nipples, ISO 4064 : 2005 with valid CE mark or ISI mark, mentioning notified body number along with MlD / OIML / ISO certification from a recognized International laboratory.AMR System :AMR System shall be Walk By / Drive By mode, Wireless AMR trans-receivers shall be directly fitted on meter or inbuilt, IP 68 protection class, water meter & AMR Module shall be of same brand, Single Command based AMR Reading and Minimum 90 days historical data retrive facility, alaram indication/ recording (for Reverse Flow, back flow, Peak Flow,Minimum Flow, Low Battery Alram, Volume below threshold, Volume above threshold, Reverse Meter, Meter Stopped), Minimum 10 years of AMR module bateery life considering one no. communication per day

METER READING DEVICE (For Manual Meter Reading / AMR Compatible / AMR Meter Reading)Hand Held Unit / Meter Reading Device having IP 65 Protection class, windows/ android software base operating system, minimum 1 GB RAM and 8 GB Flash Disk, GPRS / 3G / LTE network connectivity, GPS facility, Camera facility, data store facility,

AMR Module for upgradation of AMR Compatible Meter :AMR System shall be Walk By / Drive By mode, Wireless AMR trans-receivers shall be directly fitted on meter, IP 68 protection class, water meter & AMR Module shall be of same brand, Single Command based AMR Reading and Minimum 90 days historical data retrive facility, alaram indication/ recording (for Reverse Flow, back flow, Peak Flow,Minimum Flow, Low Battery Alram, Volume below threshold, Volume above threshold, Reverse Meter, Meter Stopped), Minimum 10 years of AMR module bateery life considering one no. communication per day.

S.O.R. Mech 2019-20Page 135 of 166

Section- "F"






Meter Reading Software No 500,000 - 500,000 18% 590,000

8

8.1

a 50 mm No 9,495 792 10,287 18% 12,139

b 65 mm No 10,603 885 11,488 18% 13,556

c 80 mm No 14,770 1,232 16,002 18% 18,882

d 100 mm No 17,935 1,496 19,431 18% 22,929

e 125 mm No 18,463 1,540 20,003 18% 23,604

f 150 mm No 21,206 1,770 22,976 18% 27,112

g 200 mm No 28,485 2,377 30,862 18% 36,417

h 250 mm No 32,705 2,728 35,433 18% 41,811

i 300 mm No 35,870 2,993 38,863 18% 45,858

8.2

a 50 mm No 16,353 1,365 17,718 18% 20,907

b 65 mm No 18,357 1,531 19,888 18% 23,468

c 80 mm No 18,463 1,540 20,003 18% 23,604

d 100 mm No 22,598 1,886 24,484 18% 28,891

e 125 mm No 33,633 2,806 36,439 18% 42,998

7.6 Meter Reading Softwre for Stadnard / AMR Compatible/ Mechnical MultiJEt AMR Meter / Ultrasonic AMR Meter:Design, Supply, Installation, Testing, Commissioning of Web Based/ Cloud Based AMR Software for Mobile Based and Web Based Application, software shall have various analysis tools which provides Alarm, Trends, Events, Data Logging and Report Facility. Software shall collect meter data, store in to cloud and export to billing system with a pre-defined file format.Considering the experience, knowledge of the meter data and expertise in meter data analysis the cloud based solution shall be provided by reputed water meter manufacturer

Water Meters (Woltman Type):

Woltman Type Bulk Water Meter- Standard:Design, Supply, Installation, Testing, Commissioning of Woltman type Bulk Water Meter, CI/ Brass/ Bronze body material, totalizer made of copper can/ suitable anti corrosive metallic material, totaliser metalic shall have 5 mm thick glass cover suitable against antifraud attempts, Flange End process connection, IP 68 protection class, Woltman type Water Meter with removable mechanism, magnetic drive, dry dial, and be fitted with a low mass rotor which is parallel to the direction of water flow and exhibits dynamic thrust relief, water meters complete with T Type strainer, ISO 4064 : 2005 with valid CE mark mentioning notified body number along with MlD / OIML / ISO certification from a recognized International laboratory.

Woltman Type Bulk Water Meter- AMR Based:Water Meter:Design, Supply, Installation, Testing, Commissioning of Woltman type Bulk Water Meter, CI/ Brass/ Bronze body material, totalizer made of copper can/ suitable anti corrosive metallic material, totaliser metalic shall have 5 mm thick glass cover suitable against antifraud attempts, Flange End process connection, IP 68 protection class, AMR Woltman Type Water Meter with removable mechanism, magnetic drive, dry dial, and be fitted with a low mass rotor which is parallel to the direction of water flow and exhibits dynamic thrust relief, water meters complete with T Type strainer, ISO 4064 : 2005 with valid CE mark mentioning notified body number along with MlD / OIML / ISO certification from a recognized International laboratory.AMR System :AMR System shall be Walk By / Drive By mode, Wireless AMR trans-receivers shall be directly fitted on meter or inbuilt, IP 68 protection class, water meter & AMR Module shall be of same brand, Single Command based AMR Reading and Minimum 90 days historical data retrive facility, alaram indication/ recording (for Reverse Flow, back flow, Peak Flow,Minimum Flow, Low Battery Alram, Volume below threshold, Volume above threshold, Reverse Meter, Meter Stopped), Minimum 10 years of AMR module bateery life considering one no. communication per day

S.O.R. Mech 2019-20Page 136 of 166

Section- "F"






f 150 mm No 35,448 2,957 38,405 18% 45,318

g 200 mm No 51,695 4,313 56,008 18% 66,089

h 250 mm No 58,025 4,841 62,866 18% 74,182

i 300 mm No 61,190 5,105 66,295 18% 78,228

8.3

a 50 mm No 3,561 297 3,858 18% 4,552

b 65 mm No 4,705 393 5,098 18% 6,016

c 80 mm No 6,567 547 7,114 18% 8,395

d 100 mm No 7,702 642 8,344 18% 9,846

e 125 mm No 9,390 784 10,174 18% 12,005

f 150 mm No 12,977 1,083 14,060 18% 16,591

g 200 mm No 18,674 1,557 20,231 18% 23,873

h 250 mm No 25,742 2,147 27,889 18% 32,909

i 300 mm No 53,172 4,436 57,608 18% 67,977

9

9.1

a 50 mm No 58,025 4,661 62,686 18% 73,970

b 65 mm No 73,850 4,661 78,511 18% 92,643

c 80 mm No 89,675 4,661 94,336 18% 111,317

d 100 mm No 136,095 7,203 143,298 18% 169,092

e 150 mm No 157,033 8,898 165,932 18% 195,799

Bulk Water Meters (Ultrasonic)/ Full Bore Inline Ultrasonic Flow Meter:

Full Bore Inline Ultrasonic Flow Meter- Inbuilt Battery Power/ Self Power operated (PN 16)Design, Supply, Installation, Testing, Commissioning of Full Bore Inline Ultrasonic flow meter with factory calibrated, Inbuilt Battery Power Operated, flanged connection, Flow sensor, Indicator, transmitter and totaliser with all accessories viz. surge arrestor, associated cables, cabinets, hardwares, etc complete as per following specifications:Flow Meter/ Sensor: Ultrasonic type, IP 68 Protection, Flanged process connection as per IS 1538 or equivalent standard, SS304/ Metallic Alloy Flow Tube, SS316/ SS 316 L/ Hastelloy Sensor, SS316/ Hastelloy Grounding Ring/ Inbuilt Grounding Electrode, Neoprene/Polyurethane/ Hard Rubber/ Rilsan lining, SS304/ Die Cast Aluminium/ Carbon steel with Anticorrosive Paint Coil Housing with Junction Box, CS flanges.Flow Transmitter/ Converter ( Remote Field Mounted inside the Cabinet): Microprocessor based, Modular design, 2 line LCD for indication of actual flow rate, forward, reverse, sum totaliser display, ±0.5% accuracy at 0.3 to 4 m/sec velocity, one scalable pulse, one status, one GPRS/ GSM output, IP 67 protection, Die cast aluminium/ polycarbonate/ SS316 with Anticorrosive Paint/ PU finish with glass window enclosure, Inbuilt EEPROM and Data Logger,20 meters cable length for sensor to transmitter communication, Minimum 5 years battery life time, 3.6 VDC Non Rechargeable Lithium-thionyl chloride/ Ni-Cd high power batteries, Real time data logging at remote location with every 1 minute frequency for storage up to 30 days period and Twice a day transmission of measured data and events via e‐mail and SMS as & when they occur by integrated GSM/GPRS modem, Reliable data storage facility through integrated SD card 32 GB.

Strainer:Design, Supply, Installation, Testing, Commissioning of External Striner for Woltman type Bulk Water Meter, Body: IS:210 FG200 , Strainer Frame : SS Perforated Sheet, SS 304, Mesh (30) : 58 Perforated Sheet, SS 304, Gasket: Rubber Cover: IS:210FG200, Stud/Bolts/Nut: IS:1363CL4.6 & CL 4.0, Eye Bolt: IS:1363CL4.6 & CL4.0, Plug:13% CR.SS (AISI 410), Flange Dimensions as per IS:1538 table 6/ BS-4504 PN16, with all necessary hardware to complete the installtion.

S.O.R. Mech 2019-20Page 137 of 166

Section- "F"






f 200 mm No 201,695 10,593 212,288 18% 250,500

g 250 mm No 247,925 10,593 258,518 18% 305,052

h 300 mm No 267,119 13,559 280,678 18% 331,200

i 350 mm No 321,775 13,559 335,334 18% 395,695

j 400 mm No 433,605 20,339 453,944 18% 535,654

k 450 mm No 456,815 23,729 480,544 18% 567,042

l 500 mm No 501,125 27,119 528,244 18% 623,328

m 600 mm No 606,625 27,119 633,744 18% 747,818

1010.1

a)

i) 0 to 1 Kg/cm2 No 1,556 130 1,686 18% 1,989

ii) 0 to 2.1 Kg/cm2 No 1,055 88 1,143 18% 1,349

iii) 0 to 4 Kg/cm2 No 950 79 1,029 18% 1,214

iv) 0 to 6 Kg/cm2 No 950 79 1,029 18% 1,214

v) 0 to 10 Kg/cm2 No 950 79 1,029 18% 1,214

vi) 0 to 21 Kg/cm2 No 950 79 1,029 18% 1,214

b)

i) 0 to 1 Kg/cm2 No 1,594 133 1,727 18% 2,038

ii) 0 to 2.1 Kg/cm2 No 1,404 117 1,521 18% 1,795

iii) 0 to 4 Kg/cm2 No 1,303 109 1,412 18% 1,666

iv) 0 to 6 Kg/cm2 No 1,303 109 1,412 18% 1,666

v) 0 to 10 Kg/cm2 No 1,303 109 1,412 18% 1,666

vi) 0 to 20 Kg/cm2 No 1,303 109 1,412 18% 1,666

10.2

a)

i) 0 to 1 Kg/cm2 No 3,033 253 3,286 18% 3,877

ii) 0 to 2.1 Kg/cm2 No 2,532 211 2,743 18% 3,237

iii) 0 to 4 Kg/cm2 No 2,427 202 2,629 18% 3,102

iv) 0 to 6 Kg/cm2 No 2,427 202 2,629 18% 3,102

v) 0 to 10 Kg/cm2 No 2,427 202 2,629 18% 3,102

vi) 0 to 21 Kg/cm2 No 2,427 202 2,629 18% 3,102

b)

Pressure & Vacuum Gauges with Accessories

100 mm Dial Size

150 mm Dial Size

Design, Supply, Installation, Testing, Commissioning of Diaphragm sealed Pressure Gauge, ±1% accuracy, Direct bottom 1/2" NPT (M) process connection, IP 67, Glycerine filled, SS304 Case with Bayonet Type Bezel, SS316 L Diaphragm, SS316 Bottom Housing Material, SS 316 Movement material, Aluminium dial with black graduation on white background, Micro Zero adjustable pointer, neoprene gasket, Blow out disc, shatter proof glass, SS tag plate etc as per IS 3624.

100 mm Dial Size

Design, Supply, Installation, Testing, Commissioning of Bourdon Type Pressure Gauge, ±1% accuracy, Direct bottom 1/2" NPT (M) process connection, IP 67, Glycerine filled, SS304 Case with Bayonet Type Bezel, SS316 L Bourdon Tube, SS 316 Movement material, Aluminium dial with black graduation on white background, Micro Zero adjustable pointer, neoprene gasket, Blow out disc, shatter proof glass, SS tag plate etc as per IS 3624.

150 mm Dial Size

S.O.R. Mech 2019-20Page 138 of 166

Section- "F"






i) 0 to 1 Kg/cm2 No 3,071 256 3,327 18% 3,926

ii) 0 to 2.1 Kg/cm2 No 2,881 240 3,121 18% 3,683

iii) 0 to 4 Kg/cm2 No 2,780 232 3,012 18% 3,554

iv) 0 to 6 Kg/cm2 No 2,780 232 3,012 18% 3,554

v) 0 to 10 Kg/cm2 No 2,780 232 3,012 18% 3,554

vi) 0 to 21 Kg/cm2 No 2,780 232 3,012 18% 3,554

10.3

a)i) -760 to 0 mmHg (-1 to 0 bar) No 1,583 132 1,715 18% 2,024

b)i) -760 to 0 mmHg (-1 to 0 bar) No 1,899 159 2,058 18% 2,428

10.4a)

i) Diaphragm Seal No 1,477 123 1,600 18% 1,888 b)

i) 3 Way Gauge Cock- SS316 No 739 62 801 18% 945

c)

i) Snubber- SS 316 No 380 31 411 18% 485

d)

i) Q Type Syphon-SS 316 No 1,161 97 1,258 18% 1,484

11

a 0 to 10 or 0 to 20 Kg/cm2 No 26,903 2,244 29,147 18% 34,393

12

Design, Supply, Installation, Testing, Commissioning of Vacuum Gauge, ±1% accuracy, Direct bottom 1/2" NPT (M) process connection, IP 67, Glycerine filled, SS304 Case with Bayonet Type Bezel, SS316 L Bourdon Tube, SS 316 Movement material, Aluminium dial with black graduation on white background, Micro Zero adjustable pointer, neoprene gasket, Blow out disc, shatter proof glass, SS tag plate etc as per IS 3624.

Design supply, installation , testing , commissioning of following Accessories

Pressure Transmitter:Design, Supply, Installation, Testing and Commissioning of Sealed Diaphragm Type Pressure Transmitter.Piezo-resistive sensor technolgy based pressure transmitter with Micro-processor based integral LED/ LCD display, with accuracy of ± 0.3% of span, external zero and span adjustment, self diagnostics, temperature sensor for compensation. 15 to 36 V DC power supply, output signal of 4-20 mA DC with HART. Minimum IP 65 degree of protection. Aluminium housing with epoxy coating, Accessories like snubbers for pump discharge applications, three way manifold, mounting brackets, name plate etc. Material for accessories shall be SS. Protection Box/Canopy shall be provided for outside installed transmitters. Pressure Transmitter shall be suitable for following Range.

Float & Board Type Level Indicator:

Diaphram seal for Pressure Gauge.SS 316 L Diaphragm, SS316 Top chamber of diaphragm, SS316 Bottom Chamber of Diaphragm, PTFE Gasket, 1/2" NPT (F) X 1/2" NPT (M) Process connection, Silicon DC 200 sealing fluid etc. complete to match pressure gauge.

Gauge cock for Pressure Gauge.3 way gauge cock, 1/2" NPT (F) X 1/2" NPT (M) Process connection complete to match pressure gauge.

Pulsation Dampner/ Snubber for Pressure Gauge.Suitable to withstand pressure up to 300 kg/cm2, Viton Gasket, 1/2" NPT (F) X 1/2" NPT (M) Process connection complete to match pressure gauge.

Syphon for Pressure Gauge:1/2" NPT (F) X 1/2" NPT (M) Process connection complete to match pressure gauge.

100 mm Dial Size

150 mm Dial Size

S.O.R. Mech 2019-20Page 139 of 166

Section- "F"






Design, Supply, Installation, Testing and Commissioning of Float & Board Type Level Indicator, guided construction, Full Range Travel, FRP/ SS316 MOC of Float and Guide Wire Rope, minimum 6” wide x aluminum powder coating with black graduations and numerical on calibrated gauge board, Red color pointer, protection conduit, Elbow pulley, Tensioner, Anchor, Rope Fastner, Gauge Brackets, Counter Weight for rope type probe, spacer between the probes, etc complete with calibration of following sizes. 0 to 1 meter

No. 12,133 1,012 13,145 18% 15,511

a ---do----: Size: 0 to 2 Meter No. 13,188 1,100 14,288 18% 16,860

b ---do----: Size: 0 to 3 Meter No. 14,243 1,188 15,431 18% 18,209

c ---do----: Size: 0 to 4 Meter No. 15,298 1,277 16,575 18% 19,559

d ---do----: Size: 0 to 5 Meter No. 16,353 1,365 17,718 18% 20,907

13

a 0 to 5 Meter No 11,816 986 12,802 18% 15,106

14

a

i) 0 to 4 Meter No 48,900 4,079 52,979 18% 62,515

ii) 0 to 10 Meter No 54,860 4,576 59,436 18% 70,134

b

i) 0 to 4 Meter No 34,710 2,896 37,606 18% 44,375

ii) 0 to 8 Meter No 38,877 3,243 42,120 18% 49,702

iii) 0 to 15 Meter No 55,124 4,599 59,723 18% 70,473

Design, Supply, Installation, Testing and Commissioning of Top mounted Displacer Type level switches with 2 nos SPDT contacts of Micro switch rated 5 A, potential free power supply, Material of wetted parts shall be SS 316 and the material of accessories shall be SS. IP 65 or equivalent degree of protection for enclosure, suitable for sump, ESR, tank, vessels and underground reservoirs. The top mounted level switches shall be supplied with still tubes to suit the requirement. . Accessories like name plate, mating flange, gaskets, fasteners, bolts & nuts, etc. shall be supplied with the Level Switch of following Range.

Float/ Displacer Type Level Switch:

Ultrasonic Type Level Transmitter with Integral Display :Design, Supply, Installation, Testing and Commissioning of NOn Contact Ultrasonic Type Level Transmitter with Integral Display.Sensor with Head Mounted Transmitter:The sensor should be non contact type, field mounting type, housing shall have minimum IP65 protection, PP/ PVC Sensor MOC, Microprocessor based indicator with LED / LCD digital display,panel/ wall mounting type, power supply shall be 110-240 Vac or 15 to 36 Vdc, 50 Hz ± 10 %.Accesories: Mounting bracket, nut, bolts etc as per system requirement and Hook up diagram of the Instruments. Level Transmitter shall be suitable for following Range.

Ultrasonic Level Transmitter

Ultrasonic Type Level Transmitter with Remote Display :Design, Supply, Installation, Testing and Commissioning of NOn Contact Ultrasonic Type Level Transmitter with Remote Display.Sensor:The sensor should be non contact type, field mounting type, housing shall have minimum IP65 protection, PP/ PVC Sensor MOC, with sensor to transmitter cable.Remote Indicator cum Transmitter: Microprocessor based indicator with LED / LCD digital display,panel/ wall mounting type, power supply shall be 110-240 Vac or 15 to 36 Vdc, 50 Hz ± 10 %.Accesories: Mounting bracket, nut, bolts etc as per system requirement and Hook up diagram of the Instruments. Level Transmitter shall be suitable for following Range.

S.O.R. Mech 2019-20Page 140 of 166

TABLE-1

CURRENT RATINGS (ac) FOR TWO, THREE & FOUR CORE

650/1100 Volts, Armoured or un-Armoured Aluminium Conductor Cables as per IS:3961 (PART II)-1967

Nominal Area of Conductor mm2

LAID DIRECT IN THE GROUND IN DUCTS IN AIR

2 Core 3,3.5 & 4 Core

2 Core 3,3.5 & 4 Core

2 Core 3,3.5 & 4 Core

Amps Amps Amps Amps Amps Amps 1.5 18 16 16 14 16 13 2.5 25 21 21 18 21 18 4 32 28 27 23 27 23 6 40 35 34 30 35 30 10 55 46 45 39 47 40 16 70 60 58 50 59 51 25 90 76 76 63 78 70 35 110 92 92 77 99 86 50 135 110 115 95 125 105 70 160 135 140 115 150 130 95 190 165 170 140 185 155 120 210 185 190 155 210 180 150 240 210 210 175 240 205 185 275 235 240 200 275 240 240 320 275 275 235 325 280 300 355 305 305 260 365 315 400 385 335 345 290 420 375

CONDITIONS OF INSTALLATION

Maximum Conductor Temperature 70°C

Ambient Air Temperature 40°C

Ground Temperature 30°C

Depth of Laying for cables in Ground 75 Cmt.

Thermal Resistivity of Soil 150 Cm/Watt.

Method of Installation Singly

Page 141 of 166

TABLE-2

Current-carrying capacities and associated voltage drops for single-core p.v.c insulated cables.

Non-armoured, with or without sheath (copper conductors)

Conductor operating temperature: 70°C

Conductor cross

Sectional Area

Installation methods (Enclosed) Installation methods (Clipped Direct) Installation method (Defined Conditions)

2 Cables single-phase a.c or d.c

3 or 4 cables three-phase a.c

2 Cables single-phase a.c or d.c

3 or 4 cables three-phase a.c

Flat or vertical (2 cables, single-phase a.c. or d.c. or 3 or 4 cables

three-phase) 3 or 4 cables

three-phase a.c Current carrying capacity

Volt drop per

ampere per metre

Current carrying capacity

Volt drop per

ampere per

metre


Volt drop per ampere per metre


Volt drop per

ampere per

metre

Current carrying

capacity

Volt drop per ampere per metre

current carrying capacity

Volt drop per

ampere per

metre Single Phase

d.c. Three

Phase 1 2 3 4 5 6 7 8 9 10 11 12 12 14 15

mm2 A mV A mV A mV A mV A mV mV A 1 14 42 12 37 17 42 16 0.37 - - - - - -

1.5 17 28 14 24 21 28 20 0.24 - - - - - - 2.5 24 17 21 15 30 17 26 0.15 - - - - - - 4 32 11 29 9.2 40 11 36 9.2 - - - - - - 6 41 7.1 37 6.2 50 7.1 45 6.2 - - - - - - 10 55 4.2 51 3.7 68 4.2 61 3.7 - - - - - - 16 74 2.7 66 2.3 90 2.7 81 2.3 - - - - - - 25 97 1.7 87 1.5 118 1.7 106 1.5 - - - - - - 35 119 1.3 106 1.1 145 1.3 130 1.1 - - - - - -

Page 142 of 166

1 2 3 4 5 6 7 8 9 10 11 12 12 14 15 a.c d.c a.c d.c

50 145 0.97 0.91 125 0.84 175 0.93 0.91 160 0.82 195 0.95 0.91 0.85 170 0.8 70 185 0.71 0.63 160 0.62 220 0.65 0.63 200 0.59 240 0.68 0.63 0.62 210 0.59 95 230 0.56 0.45 195 0.48 270 0.48 0.45 240 0.45 300 0.52 0.45 0.49 260 0.42

120 260 0.48 0.36 220 0.42 310 0.40 0.36 280 0.38 350 0.44 0.36 0.43 300 0.34 150 - - - - - 355 0.34 0.29 320 0.34 410 0.39 0.29 0.39 350 0.29 185 - - - - - 405 0.29 0.24 365 0.3 470 0.35 0.24 0.36 400 0.25 240 - - - - - 480 0.24 0.18 430 0.27 560 0.36 0.18 0.38 480 0.22 300 - - - - - 560 0.22 0.14 500 0.25 660 0.33 0.14 0.35 570 0.19 400 - - - - - 680 0.2 0.12 610 0.24 800 0.3 0.12 0.33 680 0.17 500 - - - - - 800 0.18 0.086 710 0.23 910 0.28 0.086 0.31 770 0.16 630 - - - - - 910 0.17 0.068 820 0.22 1040 0.26 0.068 0.3 880 0.15

CORRECTION FACTORS FOR AMBIENT TEMPERATURE Ambient Temperature 25°C 35°C 40°C 45°C 50°C 55°C 60°C 65°C Correction factor 1.06 0.94 0.87 0.79 0.71 0.61 0.5 0.35

Page 143 of 166

Table-3

EARTHING READY RECKONER Sr No Item Copper Aluminum GI

Weight of Conductor kg/MTR. 1 No. 14 " SWG Wire" 0.028 - 0.0254

2 No. 12 " SWG Wire" 0.049 0.0162

(6 mm2) 0.043

3 No. 8 " SWG Wire" 0.1155 0.02703

(10 mm2) 0.102

4 No. 6 " SWG Wire" 0.1668 - 0.1465 5 No. 4 " SWG Wire" 0.243 - 0.224 6 No. 2 " SWG Wire" 0.344 0.0945 0.305 7 25x3 MM Flat 0.67 0.202 0.59 8 32x6 MM Flat 1.715 0.518 1.51 9 50x6 MM Flat 2.68 0.81 2.36 10 600 x 600 x 6 MM Thick Plate 19.3 5.83 17 11 600 x 600 x 12 MM Thick Plate 38.6 11.66 34

RECOMMENDED EARTH CONDUCTORS FOR MOTORS

1 Upto 15 HP 12 Swg. 6 mm2 8 Swg. 2 Upto 20 to 30 HP 8 Swg. 10 mm2 4 Swg. 3 Upto 35 to 50 HP 4 Swg. 35 mm2 25x3 mm Flat 4 Above 50 HP 25 x 3 MM Flat 25 x 6 MM Flat 32 x 6 MM Flat

GALVANISED EARTHING DETAILS

GI Cond. Size

Area mm2

Nominal Dia mm

Approx Weight Kg/M

Approx Resistance Ohm/M.

14 S.W.G 3.24 2.03 0.026 0.0433 12 S.W.G 5.48 2.64 0.044 0.02565 10 S.W.G 8.35 3.26 0.067 0.0162 8 S.W.G 12.97 4.06 0.104 0.01063 4 S.W.G 27.27 5.89 0.218 0.00505

25x3 mm 75 - 0.600 0.0017 32x6 mm 192 - 1.536 0.0007 50x6 mm 300 - 2.400 0.00033

Page 144 of 166

TABLE-4

SELECTION TABLE FOR STARTER/RELAY/FUSE/CABLE FOR DOL MOTORS

HP 3 Phase 415V 50 HZ

KW 415V 50 HZ

Approximate Full Load current in

Amps

DOL Starter/ Contactor capacity in

Amps.

Relay Scale in Amps

Typical Backup

HRC fuse in Amps

Typical Cable size sq.mm AL

0.50 0.4 1 12 0.8-1.6 6 1.5/2.5 0.75 0.55 1.5 12 1-1.5 6 1.5/2.5

1 0.75 2 12 1.4-2 10 1.5/2.5 1.5 1.1 2.6 12 2-3 10 1.5/2.5 2 1.5 3.5 12 2.5-4 15 1.5/2.5 3 2.25 5 16 4-6 20 1.5/2.5 4 3 6.2 16 4-6 20 1.5/2.5 5 3.75 7.5 16 5.5-8 25 2.5 6 4.5 9 16 6-10 25 2.5

7.5 5.6 11 16 8-12 25 4 10 7.5 14 16 11-12 35 4

12.5 9.3 18 30 14-20 50 6 15 11 21 30 17-25 50 6

17.5 13 24 30 20-32 63 10 20 15 28 30 22-32 63 10 25 18.5 35 38 25-40 80 16 30 22 40 70 30-45 100 25 35 26 47 70 38-63 125 25 40 30 55 70 38-63 125 25 45 33.5 60 70 45-70 160 35 50 37.5 66 70 50-90 160 35 60 45 80 105 50-90 160 50 75 56 100 105 70-110 200 70 90 67.5 120 170 90-150 250 95

100 75 135 170 120-155 250 95

150 112 200 400 140-200 350 185

200 150 275 400 210-300 500 300/400

225 170 300 400 280-300 600 300/400

Page 145 of 166

TABLE-5

SELECTION TABLE FOR STARTER/RELAY/FUSE/CABLE FOR STAR DELTA MOTOR

HP 3 Phase

415V 50 HZ

KW 415V 50 HZ

Approximate Full Load current in

Amps

Star Delta Starter Contactor capacity in Amps Main/Delta Star

Relay Scale in Amps

Typical Backup

HRC fuse in Amps

Typical Cable size sq.mm AL

Supply side

Motor side

3 2.25 5 12 12 1.5-4 10 1.5/2.5 1.5/2.5 5 3.75 7.5 12 12 3-6 20 1.5/2.5 1.5/2.5

7.5 5.5 11 12 12 6-10 25 2.5 1.5/2.5 10 7.5 14 16 16 6-12 25 4 1.5/2.5

12.5 9.3 18 16 16 8-12 35 4 2.5 15 11 21 16 16 11-16 50 6 2.5 20 15 28 30 30 14-20 63 10 4 25 18.5 35 30 30 17-25 63 16 6 30 22 40 30 30 17-25 100 16 6 35 26 47 38 30 22-32 100 25 10 40 30 55 38 30 22-32 100 25 16 45 33.5 60 70 30 25-40 125 35 16 50 37 66 70 30 25-40 125 35 16 60 45 80 70 70 38-63 125 50 25 65 48.5 87 70 70 38-63 160 70 35 70 52 94 70 70 38-63 160 70 35 75 56 100 70 70 38-63 160 70 35 90 67.5 120 105 70 50-90 200 95 50

100 75 135 105 70 50-90 200 95 50 125 90 165 160 70 70-110 250 120 70 150 112 200 170 170 90-135 250 185 70 175 132 230 170 170 90-135 300 225 120 200 150 275 300 170 140-170 350 300/400 150 240 175 320 400 170 140-170 400 300/400 185 250 187.5 323 400 170 140-200 400 400 185 275 204 360 400 170 175-250 400 500 185 300 225 385 400 400 210-300 500 500 225 400 300 500 400 400 280-400 700 625 300/400

Page 146 of 166

TABLE 6

SIZE OF CAPACITORS IN KVAR REQUIRED FOR GIVEN DEGREE OF POWER FACTOR CORRECTION PER KW OF LOAD

Initial Power

Correction to 0.85 0.9 0.95 0.98 Unity

1 2 3 4 5 6 0.50 1.112 1.248 1.403 1.529 1.732 0.51 1.066 1.202 1.357 1.483 1.686 0.52 1.024 1.16 1.315 1.441 1.644 0.53 0.98 1.116 1.217 1.397 1.6 0.54 0.939 1.075 1.23 1.356 1.559 0.55 0.899 1.035 1.19 1.316 1.519 0.56 0.86 0.996 1.151 1.277 1.48 0.57 0.822 0.958 1.113 1.239 1.442 0.58 0.785 0.921 1.076 1.202 1.405 0.59 0.748 0.884 1.039 1.165 1.368 0.60 0.714 0.849 1.005 1.131 1.334 0.61 0.679 0.815 0.97 1.096 1.299 0.62 0.645 0.781 0.936 1.062 1.265 0.63 0.613 0.749 0.904 1.03 1.233 0.64 0.58 0.716 0.871 0.997 1.2 0.65 0.549 0.685 0.84 0.966 1.169 0.66 0.518 0.654 0.809 0.935 1.138 0.67 0.488 0.624 0.779 0.905 1.108 0.68 0.459 0.595 0.75 0.876 1.079 0.69 0.429 0.565 0.72 0.84 1.049 0.70 0.4 0.536 0.691 0.811 1.02 0.71 0.372 0.508 0.663 0.783 0.992 0.72 0.343 0.479 0.634 0.754 0.963 0.73 0.316 0.452 0.607 0.727 0.936 0.74 0.289 0.425 0.58 0.7 0.909 0.75 0.262 0.398 0.553 0.673 0.882 0.76 0.235 0.371 0.526 0.652 0.855 0.77 0.209 0.345 0.5 0.62 0.829 0.78 0.183 0.319 0.473 0.594 0.803 0.79 0.156 0.292 0.447 0.567 0.776 0.80 0.13 0.266 0.421 0.541 0.75 0.81 0.104 0.24 0.395 0.515 0.724 0.82 0.078 0.214 0.369 0.489 0.698 0.83 0.052 0.188 0.343 0.463 0.672

Page 147 of 166

TABLE 6 Continue….

Initial Power Correction to

0.85 0.9 0.95 0.98 Unity 1 2 3 4 5 6

0.84 0.026 0.162 0.317 0.437 0.645 0.85 - 0.136 0.291 0.417 0.62 0.86 - 0.109 0.264 0.39 0.593 0.87 - 0.083 0.238 0.364 0.567 0.88 - 0.054 0.209 0.335 0.538 0.89 - 0.028 0.183 0.309 0.512 0.90 - - 0.155 0.281 0.484 0.91 - - 0.124 0.25 0.453 0.92 - - 0.097 0.223 0.426 0.93 - - 0.066 0.192 0.395 0.94 - - 0.034 0.16 0.363 0.95 - - - 0.126 0.329 0.96 - - - 0.089 0.292 0.97 - - - 0.047 0.25 0.98 - - - - 0.203 0.99 - - - - 0.143

Sample: To find the capacitor rating required to correct a load of 100 kW

Method-1 (0.85 PF to 0.98)

Average Power Factor (CosØ1) = 0.85

Required Power Factor (CosØ2) = 0.98

Total kVAR Required= kW x [tan (cos−1Ø1) - tan (cos−1Ø2)]

Total kVAR Required=100 x [tan (cos−1 0.85) - tan (cos−1 0.98)]

Total kVAR Required=100 x [tan (0.55) - tan (0.20)] = 100 x (0.619-0.203) = 100 x 0.416

Total kVAR Required=41.6 kVAR ≅ 42 kVAR

Method-2 (0.85 PF to 0.98)

Required kVAR per kW (vide Table) = 0.417

Total Capacitor rating=0.417*100 = 41.7 kVAR ≅ 42 kVAR

Page 148 of 166

Table-7

DISTRIBUTION TRANSFORMER

Check before erection and commissioning

(1) Oil Test: 30 kV. Minimum across 2.5 mm gap for one minute. (2) Insulation test: Minimum safe insulation resistance of windings at temperature.

30°C 40°C 50°C 60°C Voltage of Meggar

415V 200 mΩ 100 50 25 500 Volts 3.3 & 6.6 kV 400 mΩ 200 100 50 1000 Volts 11 kV,22 kV & 33 kV

500 mΩ 250 125 65 2500 Volts

(3) Ratio Test: 400V should be applied to HT side and Voltage to be measured on LT side. The ratio should compare with the rated figures.

(4) Oil Level: Oil level should be checked up and topped if necessary. (5) Breather: The silica in the breather should be blue. (6) Diaphram: It should be in tact, and no crack is observed. (7) Measurement of earth resistance: this should be less than 1 ohm.

Page 149 of 166

TABLE-8

TRANSFORMER OIL (Grade)- B.30 B.S. 148

Characteristic Limit Sludge formation (Maximum) 0.3% Moisture at 15.5°C 200 Redwood seconds Moisture Nil Dielectric strength 30 kV at 15°C to 20°C using 1/3 mm.

Diameter sphere, 2.5 mm apart Flash Point (Minimum) 145°C Evaporation (Maximum) 1.6% Cold test -30°C Acidity (Neutralization value) Inorganic Nil Organic (Max) 0.5 mg KoH/gram of oil

Limits of acidity of Transformer Oil

(1) When the acidity is less than 0.2 Mg/KOH/Gm. Of oil, the oil is in good condition from the stand point of this test.

(2) When the acidity is between 0.2 mg and 0.5 mg/KOH/gm, no action need to be taken, if the oil is satisfactory in all other respects.

(3) When the acidity is between 0.5 to 1.0 Mg/KOH/gm the oil should be kept under observation and filtered if necessary.

(4) When the acidity exceeds 1 Mg/KOH/gm the oil should be reclaimed or discarded.

Page 150 of 166

Table-9

TYPE DESGINATION AND CORE IDENTIFICATION OF CABLES & WIRE AS PER IS: 1554 (1) & IS: 7098 (1)

Sr. No. Code Constituent 1 A Aluminum Conductor 2 Y Plain Copper Conductor PVC Insulated unsheathed cables 3 AY Aluminium Conductor OVC insulated unsheathed cables 4 YY Plain Copper Conductor PVC insulated unsheathed cables 4 AYY Aluminium conductor PVC insulated & PVC sheathed cables 5 YWY P/C insulated & sheathed, steel round wire armoured with copper conductor cable 6 YFY PVC insulated, Sheathed, steel flat wire armoured with copper conductor 7 AYWY PVC insulated & sheathed round steel wire armoured cable with Aluminium

conductor 8 AYFY PVC insulated sheathed, flat steel wire armoured cable with Aluminium conductor. 9 2X XLPE insulation 10 W Steel round wire Armour 11 Wa Non-Magnetic round wire Armour 12 F Steel strip Armour 13 Fa Non-Magnetic Strip Armour 14 FF Double Steel round wire Armour 15 WW Double Steel round wire Armour 16 Y PVC outer sheath

Understating cable code

1ST NUMERAL 2ND NUMERAL 3RD NUMERAL 4th NUMERAL Type of Conductor Conductor Insulation Type of Armoring Type Outer Sheath A Y F Y Aluminium Conductor PVC insulated Steel Armoring PVC Sheathed i.e AYFY- PVC insulated, PVC sheathed Steel Armored Aluminium cables

Page 151 of 166

TABLE-10

Typical mV drop Values for Joints

Sr. No. Type of Joints Test Current Max. mV permissible

Good mV

1 Terminal to link 100 2.5 0.5-1.0 2 Terminal to Lug 50 8.0 1.0-2.0 3 Terminal to Lug 100 5.0 1.0-2.0 4 Cable to Cable lug

(Crimped Joint) Rated 5.0 2.0

1. For Correct cable Lugs a. The conductor should be fully accommodated within lug. b. The cable lug should have a close fit as possible to the conductor.

2. Crimping Joints

a. Length f insulation to be stripped= barrel length+1-3 mm. b. For cable size of 35 mm2 & above two/three clamps are recommended @ 3-4 mm distance.

Page 152 of 166

Table-11

IP EXPLANATION AND RATINGS

EN 60529 outlines an international classification system for sealing effectiveness of enclosures of electrical equipment against the intrusion into the equipment of foreign bodies (i.e tools, dust, fingers) and moisture. This classification system utilizes the letters “IP” (“Ingress Protection”) followed by two or three digits. (A third digit is sometimes used. An “X” is used for one of the digits if there is only one class of protection; i.e IPX4 which addresses moisture resistance only).

Degrees of Protection-First Digit

The first digit of the IP code indicates the degree that persons are protected against contact with moving parts (other than smooth rotating shafts, etc.) and the degree that equipment is protected against solid foreign bodies intruding into an enclosure.

0 No special protection 1 Protection from a large part of the body such as a hand (but no protection from deliberate

access); from solid objects greater than 50 mm in diameter. 2 Protection against fingers or other object not greater than 80mm in length and 12 mm in

diameter. 3 Protection from entry by tools, wires, etc. with a diameter of thickness greater than 1 mm. 4 Protection from entry by solid objects with a diameter or thickness greater than 1 mm. 5 Protection from the amount of dust that would interfere with the operation of the equipment. 6 Dust tight

Degrees of Protection-Second Digit

The second digit indicates the degree of protection of the equipment inside the enclosure against the harmful entry of various forms of moisture. (e.g. dripping, spraying, submersion, etc.)

0 No special protection 1 Protection from dripping water 2 Protection from vertically dripping water 3 Protection from sprayed water 4 Protection from splashed water 5 Protection water projected from a nozzle. 6 Protection against heavy seas, or powerful jest of water 7 Protection against immersion 8 Protection against complete, continuous submersion in water.

Submersion depth and time must be specified by the end-user. The requirement must be more onerous than IP 67.

Page 153 of 166

of 166

TABLE-12

IS CODES

ELECTRICAL WORKS IS 2551 Danger Notice Boards IS 4064 Normal duty air break switches & composite units of air break switches & fuses for

voltages not exceeding 1000V IS 1818 Alternating current isolators (disconnectors) & earthing switch IS 2584 Test for Electrical Strength IS 694 PVC insulated cables. IS 375 Specification for marking and arrangement for switchgear busbar, main connection

and aux. wiring IS 5216 Safety procedures & practice in electrical works IS 2982 Copper conductors in insulated cable & chords IS 5578 Guide for marking of insulated conductor IS 1951 Polyvinyl chloride sleeving for electrical purposes IS 3010 Part-I appliances-connectors IS 3010 Part-II appliances-inlets IS 2268 Electrical call bells and buzzers for indoor use. IS 3412 Electrical water boilers IS 302 Light electrical appliances IS:2882 Storage type automatic electric water heaters IS:3202 Climate proofing of electrical equipment code of practice IS:732 Electrical wiring installation (System voltage not exceeding 650V) code of practice. IS:3106 Selection, installation and maintenance of fuses (System voltage not exceeding

650V) code of practice. IS:374 Fan and regulators ceiling type, electric IS:1258 Bayonet lamp holders IS:2086 carriers and bases used in rewireable type electric fuses up to 650V IS:5561 Electric power connectors IS:2675 Enclosed distribution fuse boards and cutouts for voltage not exceeding 1000V IS:2208 HRC Cartridge fuse link up to 650V IS:3961 Recommended current rating for Cables PVC insulated and PVC (Part-II) Sheathed

heavy duty IS:371 Ceiling roses IS:5987 Selection of switches (Voltage not exceeding 1000V) Code of Practice IS:1646 Protection for fire safety of building Electrical installation IS:3106 Selection, Installation of fuses (Voltage not exceeding 650V) IS:5133 Part-I Boxes for enclosure of electrical accessories steel and cast-iron boxes IS:5133 Part-I boxes made of insulated materials IS:5649 Adaptors for flexible steel conduits IS:419 Fittings for rigid non-metallic conduits IS:4160 Interlocking switch socket outlet IS:2412 Link clips for electrical wiring IS:2509 Rigid non-metallic conduits for electrical installation

Page 155 of 166

IS:4615 Switch socket outlet (non-Interlocking type) IS:3854 Switches for domestic and similar purpose IS:1293 Three pin plugs and socket outlet IS:3914 Selection of AC induction motor starters (Voltage not exceeding 1000V) IS:10810 Cables: method of tests IS:5908 Method of measurement of electrical installation in buildings IS:1554 Specifications for PVC insulated electric cables for working voltage up to and including

1100V IS:1753 Specifications for aluminum conductor for insulated conductors IS:3975 Mild steel wires strips and tapes for armoring of cables IS:5831 Specifications for PVC insulations and sheath of electric cables IS:2147 Degree of protection provided by enclosures for low voltage switchgear and control

gear IS:4237 General requirements for switchgear and control gear for voltage not exceeding

1100Volts IS:1886 & IS: 11028

Selection & Installation and maintenance of transformer

IS:3072 Installation and maintenance of switchgear IS:900 Installation and maintenance of induction motor IS:1255 Installation and maintenance of paper insulated power cables (up to and including

33KV) IS:1866 Maintenance of insulating oil IS:3561 Specification for electrical power connectors IS:617 Specifications for aluminum, aluminum alloy and casting for general engineering IS:159 Busbar and Busbar connections IS:2629 & IS: 2633

Galvanizing

IS:3480 Flexible steel conduit for Electrical wiring IS:3837 Accessories for rigid steel conduit for electrical wiring

IS:8623 Factory built accessories of Switchgear & Control gear for voltage up to and including

1000V AC and 1200V DC IS:4648 Electrical layout in residential buildings IS:2501 Copper tubes for general residential purposes IS:1259 Mild steel tubes IS:2667 Specifications for lightning protection against building and allied structures IS:2309 Code of practice for lightning protection against building and allied structure IS:3043 Code of practice for earthing IS:2274 Electrical wiring installation (Voltage exceeding 650V) IS:1653 Rigid steel conduits for electrical wiring (revised) with amendments IS:1915 General and safety requirements for electrical lighting fitting IS:5316 Guide for safety procedures and practices in electric works IS:5124 Code of practice for installation and maintenance for AC induction motor starters

(Voltage not exceeding 1000V) IS:1180 Outdoor type three phase distribution transformer IS:5133 Boxes for enclosures of electrical accessories

Page 156 of 166

IS 16636 Automatic Power Factor Correction (APFC) Panels for Voltage Rating upto And Including 1000 V.

IS 12615 Energy Efficient Induction Motors - Three Phase Squirrel Cage. IEC 61439 Low-voltage switchgear and control gear assemblies IS 7098 Crosslinked polyethylene insulated PVC sheathed cables IS 2705/ BS 7626

Current Transformers

IS3231,3842 BS142/ IEC 255

Electrical Relays for Power System protection

IS: 1248 BS: 89 IEC 51

Electrical Indicating Instruments

IS :722 BS: 2692

AC Electricity Meters

IEC947.4.2 EN50081-1,50082-2 & 60204-1

Microprocessor Soft Starter

IS 3427 & IS 13947

Metal Enclosed Switchgear

MECHANICAL WORKS BS 5135 Specification for are welding of carbon manganese steels BS 5316 Part-2 Specification for acceptance test for centrifugal, mixed flow and

axial pumps – Test for performance and efficiency BS 6072 Method for magnetic particle flow detection BS 6405 Specification for non-calibrated short link steel chain (Grade 30)

for general engineering purposes: Class 1 & 2 BS 6443 Method for penetrate flow detection ASTM A-36 Specification for Structural Steel ASTM A-216 Specification for Steel Castings, Carbon suitable for fusion welding

for high temperature service ASTM A-276 Specification or stainless steel and heat resisting steel bars and

shapes ASTM A-351 Specification for castings, Austenitic – Ferric (Duplex), for

Pressure containing parts ASTM A-743 Specification for castings, Iron – Chromium, Iron – Chromium –

Nickel and Nickel Base Corrosion Resistant for general Application ASTM A-744 Specification for castings, Iron Chromium – Nickel, Corrosion –

Resistant IEC – 189 Part 1 & 2

Low frequency cables and wires with PVC insulation and PVC Sheath

AWWA C 501 Cast Iron Sluice Gates ISO 17766 Centrifugal Pumps handling IS 14220 Open well Submersible Pump sets IS 8418 Horizontal centrifugal self-priming pumps IS 1710 Pumps-Vertical turbine Mixed and Axial Flow for clear cold water

Page 157 of 166

IS 6595 Horizontal centrifugal pumps for clear, cold water IS 5 Colours for ready mixed paints and enamels IS 210 Grey Iron Castings IS 318 Leaded Tin Bronze Ingots and Castings IS/IEC 60034 Three Phase Induction Motors IS 807 Code of Practice for Design, manufacture, erection and testing

(Structural Portion) of cranes and hoists IS 1239 Mild Steel tubes, tubular and other wrought steel fittings IS 1536 Centrifugally Cast (Spun) iron pressure pipe for water gas and

sewage IS 1537 Vertically cast-iron pressure pipes for water, gas and sewage IS 1538 Specification for cast iron fittings for pressure pipes for water, gas

and sewage IS 1554 PVC insulated (Heavy duty) electric cables IS 2062 Steel for general structural purposes IS 2147 Degrees of protection provided by enclosures for low voltage

switch gear and control gear IS 3177 Code of practice of electric overhead traveling cranes and gantry

cranes other than steel work cranes IS 3624 Vacuum and Pressure gauges IS 3815 Point hooks with shank for general engineering purposes

BS 2910 Methods for radiographic examination of fusion welded circumferential butt joints in steel pipes

BS 3017 Specification for mild steel forged ram shorn hooks BS 3100 Specification for steel castings for general engineering purposes BS 3923 Methods for ultrasonic examination of welds BS 4360 Specification for weldable structural steels BS 4772 Specification for ductile iron pipes and fittings BS 4870 Specification for approval testing of welding procedures BS 4871 Specification for approval the sting of welders working to approved

welding procedures BS 4942 Short chain link for lifting purposes IS 5120 Technical requirements of roto dynamic special purpose pumps IS 5600 Horizontal / vertical non-clog type centrifugal pump for sludge handling IS 8034 Borewell Submersible Pump IS 7090 Guide lines for rapid mixing devices IS 7208 Guide lines for flocculator devices IS 10261 Requirements for clarifier equipment for waste water treatment IS 8413 Requirements for biological treatment and equipment IS 8413 Part-II

Activated sludge process and its modifications

IS 10037 Requirements for sludge dewatering equipment, sludge IS 10037 Part I

Drying beds, sand, gravel and under drains

IS 6280 Specification for Sewage Screens IS 3938 Electric Wire rope hoists

Page 158 of 166

IS 6603 Stainless steel bars and Flats IS 2800 Code of Practice Construction and development of Tubewell Borewell IS 11189 Methods for Tubewell development IS 13095 Butterfly valves for general purposes Further, following codes and standards unless specified herein shall be referred to for pipe lines, pipe work & fittings: IS: 210 Specification for grey iron casting IS:290 Specification for coal tar black paint IS:456 Code of practice for plain and reinforced concrete IS :458 Specification for pre-cast concrete pipes (with and without

reinforcement) IS :516 Method of test for strength of concrete IS :638 Specification for sheet rubber jointing and rubber insertion jointing IS :783 Code of practice for laying of concrete pipes IS :816

Code of practice for use of metal arc welding for general construction in mild steel

IS :1367 Technical supply conditions for threaded steel fasteners IS :1387 General requirements for the supply of metallurgical materials IS :1500 Method for Brinell hardness test for metallic materials IS :1536 Specification for centrifugally cast (spun) iron pressure pipes for water, gas and

sewage IS :1537 Specification for vertically cast-iron pressure pipes for water, gas

and sewage IS :1538 Specification for cast iron fittings for pressure pipes for water,

gas and sewage IS :1916 Specification for steel cylinder pipes with concrete lining

and coating IS :2078 Method for tensile testing of grey cast iron IS:3589 Specification for MS Spirally Welded Pipes IS :3597 Method of tests for concrete pipes IS :3658 Code of practice for liquid penetrant flow detection IS :5382 Specification for rubber sealing rings for gas mains, water mains and sewers IS :5504 Specification for spiral welded pipes IS :6587 Specification for spun hemp yarn IS :7322 Specification for specials for steel cylinder reinforced concrete pipes IS:8329 Specification for DI pipes IS:9523 Specifications for DI fittings IS:4984 Specifications for HDPE pipeline IS:14846 Specifications for valves IS :783 Code of practice for laying of concrete pipes IS :3114 Code of practice for laying of cast iron pipes IS :3764 Excavation work - Code of Safety IS :4127 Code of practice for laying of glazed stoneware pipes IS :5822 Code of practice for laying of electrically welded steel pipes for

water supply. IS :6530 Code of practice for laying of asbestos cement pressure pipes.

Page 159 of 166

Instrumentation Codes & Standard

BIS Bureau of Indian Standard

AWWA American Water work Association

ISO International Organization for Standardization

BS British Standard

IEC International Electrotechnical Commission Standards

IS 779: 1994

Indian Standard for Water Meters (Domestic Type) Specification

IS 2373: 1981 Water Meters (Bulk Type)

IS 6784:1996

Methods for Performance Testing of Water Meters (Domestic Type) (Second Revision)

BS 7405: 1991 BS 7405 classifies closed conduit flow meters

ISO 4185:1980

Specifies a method of determining the liquid flow-rate by measuring the mass of liquid delivered into a weighing tank in a known time interval

ISO 4064-1:2014

International Organization For Standardization for Water meters for cold potable water and hot water -- Part 1: Metrological and technical requirements

ISO 4064-2:2014

Water meters for cold potable water and hot water -- Part 2: Test methods

ISO 4064-3:2014

Water meters for cold potable water and hot water -- Part 3: Test report format

ISO 4064-4:2014

Water meters for cold potable water and hot water -- Part 4: Non-metrological requirements not covered in ISO 4064-1

ISO 4064-5:2014

Water meters for cold potable water and hot water -- Part 5: Installation requirements

ISO/ IEC: 17025

General requirements for the competence of testing and calibration laboratories

ISO 6817 Measurement of conductive liquid flow in closed conduit- Methods using Electromagnetic Flow meter

ISO 12242:2012

Measurement of fluid flow in closed conduits- Ultrasonic transit time flow meters

ISO 7066-2 Assessment of uncertainty in the calibration & use of flow measurement device

ISO 3834-2: 2005

Quality requirements for fusion welding of metallic materials. Comprehensive quality requirements

IS 3043-2007 Code of practice for Safety Earthing

Page 160 of 166

IS 2309-1989 Code of Practice for the protection of buildings and allied structures against lightning.

ISO 9001:2015 Requirements for a quality management system

DNP Distributed Network Protocol

BS EN 50081 Electromagnetic Compatibility

IEEE 587 Power Supply Surge Protection

IEC 61158-2 Industrial communication networks

IS 10553-1 (1983)

Requirements for chlorination equipment, Part I: General guidelines for chlorination plants including handling, storage and safety of chlorine cylinders and drums

IS 10553-2 (1983)

Requirements for chlorination equipment, Part 2: Vacuum feed type chlorinators

IS 10553-4 (1983)

Requirements for chlorination equipment, Part 4: Gravity feed type gaseous chlorinators

IS 10553-5 (1987):

Requirements of chlorination equipment, Part 5: Bleaching powder solution feeder displacement type chlorinator

Abbreviations used for Instrumentation & Control Sr. No Short Form Full Form

1 PLC Programmable Logic Controller 2 CPU Central Processing Unit 3 DI Digital Input 4 DO Digital Output 5 AI Analogue Input 6 AO Analogue Output 7 RS 485 Recommended Standard 485 8 FO Fiber Optic 9 HMI Human Machine Interface on ICP

10 OWS Operator Work Station 11 RIO Remote Input Outputs 12 ICP Instrument Control Panel 13 MCC Motor Control Centre 14 PMCC Power cum Motor Control Centre 15 UPS Uninterrupted Power Supply 16 OLR Over Load Relay 17 STR Motor Starter 18 MOV Motor Operated Valve/ Motorized Valve

Actuator 19 DCDB DC Distribution Board 20 ACDB AC Distribution Board

Page 161 of 166

21 TCP Transmission Control Protocol 22 IP Internet Protocol 23 FIELD Field Instruments 24 BKR Breaker 25 TRAFO Transformer 26 N/A Not Applicable 27 - Details shall be furnished later 28 SD Card Secured Digital Card 29 HTTP Hypertext Transfer Protocol 30 HDMI High-Definition Multimedia Interface 31 GPS Global Positioning System 32 LTE Long Term Evolution 33 Cc/ Bcc Carbon Copy/ Blind Carbon Copy 34 DSL Digital Subscriber Line 35 URL Uniform Resource Locator 36 SMS Short Message Service 37 SSL Secure Sockets Layer 38 GIF Graphics Interchange Format 39 LCD Liquid Crystal Display

Flow Unit Conversion Sr. No Unit-1 Unit-2

1 1 Litre/ Sec = 3.6 Meter³/ Hour (M³/Hr) 2 1 Litre/ Min = 0.06 M³/Hr 3 1 Litre/ Hr = 0.001 M³/Hr 4 1000 Litre = 1 M³ 5 1 Million Litter Per Day (MLD) = 1000 (M³/Hr)

Pressure Unit Conversion Sr. No Unit-1 Unit-2

1 1 Bar = 1.01972 Kg/ Cm² 2 1 Bar = 100 kPa 3 1 Bar = 0.987 atm 4 1 Bar = 14.5038 psia 5 14.7 pounds per square inch

absolute (psia) = 0 pounds per square inch gauge (PSIG)

6 1 Megapascal (Mpa) = 10.1976 Kg/ Cm² 7 1 Millimeter Mercury (0°C) (mmHg) = 0.00136 Kg/ Cm² 8 1 Pound per Square Inch (psi) = 0.07031 Kg/ Cm² 9 10 Meter Head = 1 Kg/ Cm²

Temperature Unit Conversion 1 Degree to Fahrenheit Equation: ( T(°C) × 9/5 )+ 32 = T(°F)

Page 162 of 166

Level Unit Conversion Sr. No Unit-1 Unit-2

1 1 Meter = 1000 mm 2 1 Meter = 100 cm 3 1 Kilo Meter = 1000 meter

Page 163 of 166

11KV FOUR POLE STRUCTURE

Page 164 of 166

11KV DOUBLE POLE STRUCTURE

Page 165 of 166

Pipe Earthing and Plate Earthing Arrangement

Page 166 of 166

Nomenclature for DP Structure

Item No

Description

01 ACSR DOG CONDUCTOR 02 LIGHTNING ARRESTOR 03 11KV STRAIN INSULATOR DISC 04 11KV INSULATOR WITH PIN -5KN 05 11KV, 200A AB SWITCH WITH EARTH SWITCH 06 11KV 25A DO FUSE 07 STAY SET 08 DANGER BOARD 09 150MM DIA GI PIPE 3M LONG

10

GI CHAIN LINK WIRE FENCE, 2M HEIGHT VERTICAL SUPPORT INCLINED VERTICAL SUPPORT 2 ROWS LINE WIRE

11 1.5M WIDE X 2.5 M LOCKABLE GATE 12 OUTDOOR CABLE TERMINATION KIT 13 R.S.J. POLE 175 X 85 MM SIZE WITH 11M LONG 14 ISMC CHANNEL 15 BASE PLATE FOR POLE 16 1.0M LIGHTNING SPIKE 17 ANTI-CLIMBING DEVICE 18 25X6 MM GI FLAT

Nomenclature for Four Pole Structure

Item No

Description

01 10KV, 10KA Distribution type LA 02 11KV, 200A GOD Switch with Operating Handle 03 11KV Drop out Fuse 04 11KV Disc insulator string 05 11KV Pin Insulator 06 ACSR DOG CONDUCTOR 07 Anti-Climbing Device 08 DANGER BOARD 09 STAY SET 10 R.S.J. POLE 175 X 85 MM SIZE WITH 11M LONG 11 ISMC CHANNEL 12 ISA Angle 50 x 50 x 6

13

GI CHAIN LINK WIRE FENCE, 2M HEIGHT VERTICAL SUPPORT INCLINED VERTICAL SUPPORT 2 ROWS LINE WIRE

14 2.5M (WIDE) x 2M (HEIGHT) Lockable Gate 15 ISMC Channel (75 x 40 x 6 mm) - Tension Stringing Hardware suitable for Single ACSR DOG

Conductor - Cable Clamps - 40mm dia GI straight Length GI conduit Pipe - 150mm dia GI straight Length GI conduit Pipe - PG Clamps - GI Lightning Spike of 25NB (1M long) with test link

arrangement - Outdoor cable termination kit - MS Base plate 400 x 400 x 8 Thk - 25 x3 GI Flat - Barbed Wire

gujarat water supply & sewerage board...gujarat water supply & sewerage board

Documents