Hitchins Swimming Pool

Download Hitchins Swimming Pool

Post on 06-Mar-2016

217 views

Category:

Documents

3 download

Embed Size (px)

DESCRIPTION

Double Protection Waterproofing for suspended swimming pool

TRANSCRIPT

<ul><li><p>Hitchins Product Presentation </p><p>Is a special blend of cement, quartz sand and multiple activating chemical in powder form. Upon application the chemical will react to form insulable crystals that penetrate deep into the concrete. Type : Crystalline, Integral </p><p>Consumption : 1 x coating @ 1,0 kg/ m </p><p>Two component cementitious waterproofing system that has excellent flexibility and strength. It is used in situation where movement or cracking of the substrate is occuring or anticpated. </p><p>Type : Cementitious membrane Consumption : 2 x coating @ 1,0 kg/ m </p><p>FORMDEX PLUS: </p><p>FORMDEX UNIFLEX: </p><p>SWIMMING POOL </p><p>(SUSPENDED STRUCTURE) </p></li><li><p>Hitchins Product Presentation </p><p>APPLICATION PROCEDURE </p><p> All surfaces to be waterproofed shall be cleaned by wire brushing, scraping or any other suitable means to remove dirt, grease, mould, etc. </p><p> All concrete surface should be dampen prior to waterproofing application. </p><p>Surface Preparation: </p><p> All new concrete surfaces shall be cured for a minimum of 14 days before the Waterproofing can be applied. </p></li><li><p>Hitchins Product Presentation </p><p>Formdex Plus: Mixing: Add 5 part of powder to 2 part of clean water by volume, and </p><p>mix thoroughly for at least 3 minutes. </p><p> Mix only sufficient material that can be used up within its pot life (approx. 20 minutes). </p><p> Apply waterproofing slurry mix in 1xcoat @ 1.0 kg/m. Allow 3 hours drying time between each coats. </p><p>Apply by brush of Formdex Plus, 1x coating </p><p>= Formdex Plus, 1.0 kg/m </p></li><li><p>Hitchins Product Presentation </p><p> Mixing: Add 3 part of powder to 2 part of liquid by volume, and mix thoroughly with a mechanical mixer for at least 3 minutes. </p><p> Mix only sufficient material that can be used up within its pot life (approx. 60 minutes). </p><p> Apply waterproofing slurry mix in 2x coat @ 1.0 kg/m. </p><p>Formdex Uniflex: </p><p> Allow 3 hours drying time between each coats. </p><p>Apply by brush of Formdex Uniflex, 2x coating </p><p>= Formdex Uniflex, 2.0 kg/m </p><p>= Formdex Plus, 1.0 kg/m </p></li><li><p>Hitchins Product Presentation </p><p>= Formdex Uniflex, 2.0 kg/m </p><p>DETAIL - INSTALLATION </p><p>= Formdex Plus, 1.0 kg/m </p><p>Pekerjaan plester pelindung. </p><p>= Lapisan Finishing </p></li><li><p>Hitchins Product Presentation DETAIL - LIGHTING </p><p>= Formdex Plus, 1.0 kg/m = Formdex Uniflex, 2.0 kg/m </p><p>= Epoxy mortar </p></li><li><p>Hitchins Product Presentation DETAIL - PIPE PENETRATION </p><p>= Formdex Plus, 1.0 kg/m = Formdex Uniflex, 2.0 kg/m </p><p>= Epoxy mortar </p></li><li><p>Hitchins Product Presentation </p></li><li><p>Hitchins Product Presentation </p></li></ul>