labconco waterpro water purification systems

How To Use This Catalog

This catalog contains complete information on the full line ofLabconco Water Purification Systems. The catalog begins with anoverview of the various water purification technologies available.Next, the WaterPro Water Purification Systems information isorganized by System category.

Within these sections you will find general introductory informationabout each water purification system followed by features and bene-fits, a flow chart that describes the built-in purification technologies,specifications and ordering information, performance data, technicalspecifications, replacement supplies and dimensional data. Please referto the Table of Contents below for the specific page number for eachwater purification system.

Before turning to a section, refer to the Selection Guide on page 5 toquickly and easily pinpoint the right purification method for yourapplication. Additional information about Labconco WaterPurification System selection is available by calling 800-821-5525 or816-333-8811.

Water Pure Enough For Laboratory Use

In the laboratory, tap water is not pure enough for experimentaluse. Analytical researchers are commonly concerned with ele-ments and compounds in the parts per billion range. Life scienceresearch is often very sensitive to many contaminants, particularlyheavy metals and dissolved organics. High performance liquidchromatography (HPLC) requires ultrapure water for calibrationof detector base lines and elution of reverse phase columns. HPLCneeds water essentially free from dissolved or colloidal ionic andorganic contaminants. Atomic absorption spectrometry (AAS)requires pure water that is very low in inorganic, organic or col-loidal contaminants. Trace element analysis requires water that isfree of the elements being examined.

In response to the increasing sensitivity of their research, severalprofessional organizations have established water quality stan-dards. Three of these standards and their key aspects are summa-rized below:

CLSI C3-A4, Vol. 26 No. 22Preparation and Testing of Reagent Water in the ClinicalLaboratory: Approved Guideline—Fourth EditionProvides guidelines on water purified for clinical laboratory use; methods formonitoring water quality and testing for specific contaminants; and water sys-tem design considerations.

Clinical and Laboratory Standards Institute940 West Valley Road, Suite 1400Wayne, PA 19087-1898Telephone 610-688-0700www.clsi.org

ISO 3696: 1987Water for analytical use — Specification and test methodsSpecifies the requirements and test methods for three grades of water for labora-tory use for the analysis of inorganic chemicals. It is not applicable to water fororganic trace analysis, to water for the analysis of surface active agents, or towater for biological or medical analysis.

International Organization for Standardization (ISO)1, ch. de la Voie-Creuse,Case postale 56CH-1211 Geneva 20, SwitzerlandTelephone +41 22 749 01 11www.iso.org

ASTM D 1193 - 06Standard Specification for Reagent WaterDescribes the required characteristics of waters needed as a component of ananalytical measurement process and deemed suitable for use with the Standardsunder the jurisdiction of ASTM. Specifies four types of water and three addition-al grades related to microbiological contaminants that can be applied to thesefour types. See the chart on the following page.

ASTM International100 Barr Harbor DriveP.O. Box C700West Conshohocken, PA 19428-2959Telephone 610-832-9585www.astm.org

Overview

Table of Contents

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Selection Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

WaterPro RO Stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Features and Benefits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Expendables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11Dimensional Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

WaterPro PS Polishing Stations . . . . . . . . . . . . . . . . . . . . . 12-20Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Features and Benefits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-17Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Expendables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Dimensional Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

WaterProCatalog0210_WaterPro Catalog 12/01 2/19/10 1:48 PM

Overview

1

Contaminants and Water Testing

The five types of contaminants commonly found in water are:

1. Particulates2. Dissolved inorganics (solids and gases)3. Dissolved organics4. Microorganisms5. Pyrogens

PARTICULATES include silt, plumbing pipe debris and colloids.These suspended particles can plug filters, valves, tubing andreverse osmosis membranes. Particulates are visible as cloudinessor turbidity, and are detected using filtration and gravimetricmeans, or microscopic methods.

DISSOLVED INORGANICS include calcium and magnesiumions dissolved from rock formations (these two ions make waterhard), gases such as carbon dioxide that ionize in water (carbondioxide dissolves readily in water to make mildly acidic carbonicacid), silicates leached from sandy river beds or glass containers,ferric and ferrous ions from rusty iron pipes, chloride and fluorideions from water treatment plants, phosphates from detergents,nitrates from fertilizers, and many others.

There are several tests for identifying specific dissolved inorganics.The simplest test is a direct measurement of electrical conducti-vity or resistivity. Most dissolved inorganics are either negativelycharged (anionic) or positively charged (cationic), and transmit acurrent when a voltage is applied to electrodes inserted in thewater. The more ions present, the greater the conductivity, or thelower the resistivity of the sample water.

Conductivity is expressed in microsiemens/cm and is used tomeasure water with a large number of ions. Resistivity isexpressed in megohms-cm and is used in the measurement ofwater with few ions. Conductivity and resistivity are reciprocalsof each other. Thus, at 25° C, 18.2 megohm water, which is thehighest purity water obtainable with today’s technology, has aconductivity of 0.055 microsiemen/cm.

Type I Type II Type III Type IVResistivity,megohms-cm, at 25° C 18.0 1.0 4.0 0.2

pH, at 25° C NA NA NA 5-8

TOC, µg/L (max) 50 50 200 NS

Sodium, µg/L (max) 1 5 10 50

Chloride, µg/L (max) 1 5 10 50

Total Silica, µg/L (max) 3 3 500 NA

Type A Type B Type C

Bacteria, CFU/100 ml (max) 1 10 1000

Endotoxin, EU/ml <0.03 0.25 NA

Weak solution ofsodium chloride

Sodium ion

Chloride ion

ELECTRONFLOW

1cm

1cm1cm

This figure shows the standard configuration of a conductivity cell and the move-ment of the anions (-) and cations (+) toward the charged poles.

Reprinted from Handbook of Water Purification 1987 by courtesy of Walter Lorch, editor,and McGraw Hill, publisher.

Resistivity 0.1 1.0 10.0 18.2 megohm-cm

Conductivity 10.0 1.0 0.1 0.055 microsiemens/cm

ASTM Reagent Grade Water Specifications

Type I water requires the use of a 0.2 µm membrane filter and feedwater to the polishing loop must have a maximum conductivity of 20 µS/cm at 25° C. Type III water requiresthe use of a 0.45 µm filter.


are tiny spherical plastic beads through which the feedwaterpasses. After a period of time, cations and anions from the waterdisplace all the active hydrogen and hydroxyl groups in the beadsand the resin must be replaced or regenerated.

Deionization has several advantages: It is an on-demand processsupplying purified water when needed. Polishing grade mixedbed deionization resin removes almost all the ionic material in thewater to a maximum resistivity of 18.2 megohm-cm (at 25° C).

Deionization alone, however, does not produce absolutely purewater. Tiny fragments of the ion exchange resin are washed outof the system during operation. Stagnant water in the cartridgespromotes excessive bacterial growth. Finally, deionization doesnot remove all dissolved organics from the feedwater, and in fact,dissolved organics can foul the ion exchange resin. So, deioniza-tion is combined with other purification technologies to achievethe level of purity required in research.

How Deionization Works

Overview

2

DISSOLVED ORGANICS may include pesticides, herbicides,gasoline, and decayed plant and animal tissues. Dissolved organ-ics may also include the plasticizers leached out of plumbinglines, fittings and storage tanks.

Note the sources of plasticizers — all are from improperlydesigned water purification systems. Thus, a water purificationsystem must both remove the contaminants present in the feed-water, and be designed to minimize the addition of contaminantsto the water.

The absence of dissolved organics is very important when per-forming analyses of organic substances in HPLC, gas chromatog-raphy, electrophoresis, and fluoroscopy, or in research involvingtissue cultures. Total Organic Carbon (TOC) analyzers, which oxi-dize the organics and measure the CO2 liberated, are used todetermine organic levels in Type I water.

MICROORGANISMS constitute another group of contaminantsfound in water. Surface water may contain a wide variety ofmicroorganisms, including bacteria, protozoa, algae and others.Since most laboratory water comes from municipal water treat-ment plants, which is extensively treated to remove microorgan-isms, the chief microbes of concern for water purification systemsare bacteria.

Bacteria enter an unprotected water purification system from thefeedwater, any breaks in the system or through the dispenser.Once in the system, bacteria secrete a polymeric substance thatadheres them to surfaces of storage tanks, deionization cartridges,plumbing and hard-to-clean surfaces.

Bacteria are usually detected and enumerated by filtering thesample water through a 0.45 micron filter and culturing the filteron a suitable medium for several days. Bacteria counts arereported in colony forming units per milliliter (cfu/ml).

Pyrogens are typically gram-negative bacterial cell wall fragmentsor lipopolysaccharides. When injected into a mammal, pyrogenscause a rise in body temperature. Thus, pharmaceutical-gradewater must be pyrogen-free. Pyrogens also have a detrimental orlethal effect on tissue cultures.

Pyrogens are detected using the LAL (Limulus AmoebocyteLysate) test, a sensitive test for very low concentrations oflipopolysaccharides.

Purification Methods

Labconco’s water purification systems combine seven differenttechnologies to produce laboratory pure water:

1. Deionization 5. Microporous Filtration2. Reverse Osmosis 6. Ultrafiltration3. Activated Carbon Filtration 7. Ultraviolet Oxidation4. Organic Adsorption

DEIONIZATION is commonly used in laboratories for producingpurified water on-demand. Deionization functions by exchanginghydrogen ions for cationic contaminants and hydroxyl ions foranionic contaminants in the feedwater. The deionization resins

H

H

H

(a) (c)

(b)

(c)(a)

(b)

Ca2+

R-H

H

HH H+

H+

H+ H+

H

H

H

H

H

H

H

H

H

Ca

H

OH -

CI -

OH

OH

OH

OH

OH

OH

OH

OH

OH

OH

CI

OH

OH

OH-

H2O

OH

OH

OH

OH

Ca2+

CI -

+

(d)

R-

R-

R+

R+

R+

Anions and cations in the feedwater (a), pass through the ion exchanger resins (b) andreplace the hydrogen and hydroxyl ions attached (c). The hydrogen and hydroxyl ionsthen combine to form pure water molecules (d).

REVERSE OSMOSIS can best be explained after understandingthe natural process of osmosis. Osmosis is the movement of wateracross a semipermeable membrane from the less concentrated(purer) side to the more concentrated (saltier) side (A). This move-ment continues until the concentrations reach equilibrium or thepressure on the more concentrated side becomes high enough tostop the flow (B). Osmosis is the natural process by which water isdrawn into a plant’s root, or moved from one cell to another inour bodies.

If a pressure greater than the osmotic pressure is applied to themore concentrated solution, using a high pressure pump, watermolecules are pushed back across the membrane to the less con-centrated side, yielding purified water (C). This is the process ofreverse osmosis.


PERMEATE�FLOW

CONCENTRATE FLOW

FEED FLOW

PERMEATE�FLOW

3

Reverse osmosis typically removes 90-99% of most contaminants.A table of reverse osmosis performance characteristics follows:

A granular activated carbon filter is also often placed in thepolishing loop of a water purification system to remove traceamounts of dissolved organics.

MICROPOROUS FILTRATION or submicron filtration uses amembrane or hollow fiber with an absolute pore size of 0.2micron that prevents any contaminant larger than 0.2 micronfrom passing through it. The submicron filters retain carbon finesfrom the carbon cartridge, resin fragments from the deionizationcartridges and any bacteria that may have entered the system.

CLSI considers water to be particulate-free when it has beenpassed through a 0.2 micron filter. Microporous membranes areconsidered to be indispensable elements of a water purificationsystem, unless they are replaced by an ultrafilter.

ULTRAFILTRATION uses a membrane very similar in design toreverse osmosis systems, except that the ultrafilter’s pores areslightly larger. The ultrafilter is used to remove pyrogens from thepurified water.

Since a high percentage of the water brought to the ultrafilterpasses through it, it will eventually plug if not maintained. In aproperly designed system, the ultrafilter is regularly and tangen-tially washed free of contaminants. With this type of design,ultrafiltration is an outstanding technology for ensuring veryconsistent ultrapure water quality.

ULTRAVIOLET OR PHOTO OXIDATION uses ultraviolet radi-ation at the biocidal wavelength of 254 nanometers to eliminatebacteria from the system. It also cleaves and ionizes certainorganics at 185 nanometers for subsequent removal by the deion-ization and organic adsorption cartridges in the polishing loop.

Overview

Osmotic�Pressure

Osmotic Head�(Pressure)

Pure�Water

Semi-PermeableMembrane

(A) OSMOTIC FLOW

Salt�Solution

Osmotic�Pressure

Pump�Pressure

H2OH2OH2O

H2OH2OH2O

Pure�Water


(C) REVERSE OSMOSIS

Feed�Water

Pure�Water


(B) OSMOTIC EQUILIBRIUM

Salt�Solution

Contaminant % Removal Efficiency

Suspended solids 100

Bacteria 99.5

Viruses 99.5

Pyrogens 99.5

Organics, molecular weight > 250 Daltons 97-99.5

Monovalent inorganics 94-96

Divalent inorganics 96-98

Trivalent inorganics 98-99

Crossflow filtration in an ultrafilter showing pyrogens and particles being retained,while only water molecules pass through the pores. Illustration courtesy of OSMONICS, INC., Minnetonka, MN, USA.

Reprinted from Handbook of Water Purification 1987 by courtesy of Walter Lorch, editor,and McGraw Hill, publisher.

Because of its exceptional purifying efficiency, reverse osmosis isa very cost effective technology for a water purification system.Because reverse osmosis removes a high percentage of contami-nants, it is often used as a pretreatment process which significantlyprolongs the life of the deionization “polishing” cartridges. Asystem which allows dispensing of the reverse osmosis water givesa source of high quality pre-purified water suitable for manyroutine laboratory purposes.

ACTIVATED CARBON FILTRATION removes chlorine bychemisorption and dissolved organics by adsorption and is oftenfound at two places in a water purification system. Because thinfilm composite reverse osmosis membranes are sensitive to chlo-rine, and to a lesser degree, fouling from dissolved organics, acti-vated carbon is often placed before the RO membrane to removethese contaminants.


The Right Purification Method For You

Choosing the right purification method for your laboratorydepends on several factors.

1. Consider your application. For example, are you perform-ing HPLC, Atomic Absorption, Mass Spectrometry or GasChroma-tographic Analyses? If you answered “yes” to any ofthese applications, then you may need a system that uses activat-ed carbon filtration, organic adsorption and deionization tech-nologies. Does your work require that your water be bacteria-free? If yes, then you must choose a system that incorporatesmicroporous filtration or ultrafiltration.

2. Consider the quantity of water used each day. Choosea system that best meets your requirements.

3. Consider the quality of your feedwater. Identifying thecontaminants and their concentrations present in your feedwaterwith the free WaterProfile™ analysis kit will help you select theappropriate water purification system for your needs.

Labconco’s Approach To Water Purification

Labconco’s water purification systems were designed to directlyaddress the shortcomings found in traditional approaches towater purification. The concepts that Labconco brings to the fieldof water purification, along with our high standards for qualityconstruction of laboratory equipment, excellent service and oneyear warranty are:

Recirculaton throughout the polishing system, to the dispenser,to minimize bacterial buildup found in stagnant water.

Unique dispensing gun for sensitive one-hand control of flowrates and enhanced flexibility.

Informative diagnostic panels to relay system status andperformance.

Timed dispense for user convenience when large volumes arerequired.

Highest quality materials, including spiral wound thin filmcomposite reverse osmosis membranes, nuclear grade resins andall inert materials of construction in the water pathway.

To Serve You

The Labconco Sales Support Center is available to provide imme-diate assistance. Just call 800-821-5525 or 816-333-8811 foranswers to questions about applications, product selection, speci-fications and service. Or visit www.labconco.com for electronicaccess to product information.

Let Us Help You ChooseA Water Purification System To Meet YourSpecific Laboratory Requirements

The free WaterProfile water analysis kit is a good first step. Torequest this service, simply complete the WaterProfile postcardlocated in the back pocket of this catalog, call LabconcoCustomer Service at 800-821-5525 or 816-333-8811 or visit ourwebsite at www.labconco.com. The WaterProfile Kit includes aquestionnaire to help pinpoint your application needs, a bottle tofill with your feedwater (tap or pretreated) and a label and pack-aging for returning the kit to Labconco. After we conduct a seriesof diagnostic tests, you receive a report detailing your tap waterquality and recommendations on the appropriate WaterPro WaterPurification System for your laboratory.

Overview

4


WaterPro RO GeneralHPLC UF

HPLC/UFStation Chemistry Hybrid

Water TechnologiesCarbon Filtration • • • • •Reverse Osmosis •Deionization • • • •Organic Adsorption • •Ultrafiltration • •Ultraviolet Oxidation • • •Microporous Filtration Optional Optional Optional Optional

MountingWall • • • • •Bench Accessory Accessory Accessory Accessory AccessoryMobile Accessory Accessory Accessory Accessory Accessory

DispensingTypical Flow Rate–Maximum Liter/Min. (at 25° C) 1.0 1.8 (1.2*) 1.8 (1.2*) 1.1 (1.0*)† 1.8/1.1 (1.1*/1.0*)†**Minimum Feedwater Quality Tap Pretreated (100µS) Pretreated (100µS) Pretreated (100µS) Pretreated (100µS)Gun and Valve — Timed Dispense Accessory • • • •Valve Only — Timed Dispense • • • • •

ApplicationsGeneral Lab Procedures

Pretreatment for:Glassware WashingRODeionization System •

Glassware Rinsing • • • • •Qualitative Applications • • • •Buffer Solution Prep • • • • •Standard Solution Prep • • • • •

Inorganic AnalysesIon Chromatography • • • •Inductively Coupled Plasma/ • • • •Mass SpectroscopyAtomic Absorption • • • •Flame Emission Spectroscopy • • • •Trace Metal Analysis • • • •

Organic AnalysesLiquid Chromatography • • •HPLC • •Gas Chromatography • •Electrophoresis • • •Total Organic Carbon • •

Life SciencesTissue Culture • •Clinical • •General Microbiology • • •General Immunology • • •Recombinant DNA • •

5

Selection Guide

* rate with optional Hollow Fiber Final Filter installed† actual flow rates for ultrafiltered models could vary as much as ±15% due to membrane navigation** rate through dispensing valve/rate through dispensing gun

W A T E R P R O P S P O L I S H I N G S T A T I O N


WaterPro RO Stations

6

WaterPro® RO Stations produce Type III waterat a rate of 1 liter per minute

The WaterPro® RO Station with its large capacity filters and mem-brane delivers high-quality reverse osmosis (RO) purified waterType III water* at a typical rate of 1 liter per minute (at inlet watertemperature of 25° C). RO purified water is ideal for laboratoryapplications such as reagent preparation and glassware rinsing.

Water may be dispensed manually from a valve or an optionalgun. Water from the valve may also be activated automaticallyby using the exclusive timed dispense feature that allows forunattended operation. Simply set the timer up to 99.9 minutes,

press the dispense button and walk away. The valve dispensesuntil the set time has expired.

The WaterPro RO includes an outlet port for connection to alaboratory glassware washer such as Labconco’s SteamScrubber® orFlaskScrubber®. With its 17 liter tank, the WaterPro RO holdsample volume to supply the Labconco washer with pure water fortwo rinse cycles.

The WaterPro RO may also be used to pretreat feedwater for ulti-mate purification by a polishing system. The WaterPro RO may beeasily connected to any Labconco WaterPro PS Polishing Stationto allow dispensing of both RO and Type I water.

User-friendly control panelwith digital display

Timed dispense

••

Internal pressure gauge

Optional WaterPro PSElectrical Connection

Cord 13060-00

Air vent filter maintainswater quality

Quiet 1/4 hpmotor/rotary vane

pump

Integral 17 literpolypropylene

storage tank

Fastest delivery rateavailable

Large capacity whitepolypropylene bowls

Dispensing valvedelivers a controlledstream of water

Easy installation Attractive andcorrosion-resistantType 304 stainlesssteel front panel

Full one year warranty

Automatic flush valve extends RO membrane life

•

•

Optional DispensingGun 9113100

•

•

• • •

•

Exclusive feature

* Meets ASTM Type III water standard with feedwater purity of 100 µs or better.



7

Fastest delivery rate available. The WaterPro RO supplies purewater to the dispensing valve or optional gun at a typical rate of1 liter per minute. From the storage tank, purified water typicallyflows at 8.7 liters per minute (gravity fed) or may be drawn intothe WaterPro PS Polishing Station, SteamScrubber or FlaskScrubberby the polishing station or washer pump.

Large capacity white polypropylene bowls require infrequent filterchanges. Threaded heads seal tightly to eliminate leaks. The threebowls accommodate one 5-6 micron prefilter, one carbon filterand one RO membrane (expendables must be ordered separately).

Attractive and corrosion-resistant Type 304 stainless steelfront panel. The epoxy-coated steel cabinet with stainless steelfront panel houses the motor and pump for quiet operation.

Timed dispense for unattended operation. When TIME DISP.is selected, time of water delivery may be set in minutes from 0 to99.9 with the increase/decrease control button. Pressing theDISPENSE switch initiates the water delivery from the dispensingvalve. Water delivery automatically ceases when time expires,facilitating unattended operation.

User-friendly control panel with digital display. Touch-pad con-trols allow the user to select and view water quality (1 to 999microseimens), water temperature (° C) or timed dispense (0 to99.9 minutes) on the LED display. An indicator light glows greenwhen the parameter selected is displayed. Pressing the ON/OFFswitch to ON lights the LED display. A TANK FULL indicator lightglows green when the storage tank has reached capacity.

Quiet 1/4 hp motor/rotary vane pump operates at less than56 decibels. A low pressure switch prevents pump damage.

Integral 17 liter polyethylene storage tank includes an outletport for connection to a polishing station and/or a glasswarewasher.

Air vent filter maintains water quality by removing bacteriaand other particulate contaminants prior to air entering thestorage tank.

Easy installation. A tap water line, drain, electrical outlet andexpendables are needed for operation. The WaterPro RO Stationmay be mounted on the wall or other vertical surface. An optionalsupport stand allows the system to be bench mounted.

Automatic flush valve extends RO membrane life. It maintainswater purity by automatically initiating the purification process,flushing the RO membrane and tank for three minutes after each12 hour period of inactivity.

Dispensing valve delivers a controlled stream of water. Its 3/8"OD stem adapter allows connection to tubing. The DISPENSEbutton on the front panel electrically controls water delivery.

Internal pressure gauge provides readings from 0 to 160 psi ofRO-purified water and is accessible by removing the front panel.It is designed for use when troubleshooting. A back pressure ROmembrane relief valve is preset to 150 psi.

CE marking. Model 9075002 for operation on 230 volt, 50 Hzconforms to electrical safety and electromagnetic compatibilitystandards as set by the European Community.

Full one year warranty is provided against defects in materialsand workmanship.

Optional Dispensing Gun 9113100 is offered as an accessory. Thetrigger on the gun may be operated with one hand and providesdrop-by-drop control or locks to provide a continuous stream ofwater.

Optional WaterPro PS Electrical Connection Cord 1306000 isoffered as an accessory. When mounting the WaterPro PSPolishing Station on the left side of the WaterPro RO Station, thiscord allows electrical connection between the two so that onlyone electrical outlet is required.

WaterPro RO Station 9075000 with optional dispensing gun 9113100 WaterPro RO Station 9075000

Exclusive feature



8

Reverse Osmosis(RO) Membrane

CarbonFilter

Prefilter

Specifications9075000 WaterPro RO StationBowls. Constructed of white polypropylene. Bowls are included for oneprefilter, one carbon filter and one reverse osmosis membrane. A spannerwrench is provided for filter changes. Cartridges are not included. Refer toPrefilter/Carbon Filter Kit 9067201 and Reverse Osmosis Membrane9078700.

Cabinet. Overall dimensions (including bowls): 31 1/8" w x 7 23/32" d x30 3/8" h (79 x 19.6 x 77.2 cm). Constructed of epoxy-coated steel withType 304 stainless steel front panel. Includes 1/4 hp motor/rotary vanebooster pump, RO membrane back pressure relief valve preset to 150 psi,internal pressure gauge with range from 0 to 160 psi, automatic flushvalve, air vent filter, tank check valve and hardware for wall mounting.

Control Panel. Includes ON/OFF switch; LED display; µS, TEMP ° C, TIMEDISP. and TANK FULL indicator lights; DISPENSE switch for water deliverycontrol from valve; MODE switch for selecting LED display; and increase/decrease switch for setting dispensing time from 0 to 99.9 minutes.Depending on mode selected, LED display shows actual water quality from1 to 999 microseimens (µS), actual water temperature in ° C or dispensetime in minutes.

Dispensing Valve. Typically delivers 1 liter/minute of RO-purified waterby pressing the DISPENSE switch or activating TIME DISP. If TIME DISP.is activated, water dispensing from the valve automatically shuts off onceuser-set time has elapsed. Includes hose barb fitting for 3/8" ID tubing.

Electrical Requirements. 115 volts, 60 Hz, 12 amps AC. Includes an 8-foot,3-wire cord and plug.

Plumbing Connections. Feedwater line should be 3/8" OD rigid plastictubing or 1/4" ID flexible tubing. Drain lines from the flush valve andRO station are provided.

Storage Tank. Constructed of polyethylene with 17 liter capacity. Housingis thermoplastic and epoxy-coated steel. Includes outlet port for 1/2" ODplastic tubing for connection to polishing station and/or glassware washer.Shipping weight 100 lbs. (45 kg)

*9075002 WaterPro RO StationSpecifications are the same as for 9075000 except for the following changes.

Agency Approval. Station conforms to European Community electricalsafety and EMC directives and has CE conformity markings.Electrical Requirements. 230 volts, 50 Hz, 6 amps AC. Includes an 8-foot,3-wire cord. An electrical plug is required.

* International electrical configuration

Purification Technologies/Features:

PrefilterThe prefilter removes particulates larger than five micronsfrom the feedwater protecting the reverse osmosis membrane.

Carbon FilterAn activated carbon filter removes organics and chlorinefrom the feedwater. Provides protection for the reverseosmosis membrane.

Reverse Osmosis (RO) MembraneA thin film composite membrane removes up to 99% ofinorganics, organics and colloids.


Expendables

9067201 Prefilter/Carbon Filter Kit required for operation.Includes Prefilters (3) and Carbon Filters (3), for initialstart-up and two filter changes. Shipping weight 10 lbs. (4.5 kg)

9078700 Reverse Osmosis Membrane required for operation.Shipping weight 6 lbs. (2.7 kg)

Accessories

1306000 WaterPro RO/PS 125/230 Volt, 10 amp ElectricalConnection Cord Three wire cord with a plug on bothends allows electrical connection between the left sideof the WaterPro RO Station and the right side of theWaterPro PS Polishing Station. The cord and plugincluded with the WaterPro RO Station then plugs intoan electrical receptacle to supply power to both watersystems. For use with either 115 volt, 60 Hz WaterProRO and PS models or 230 volt, 50 Hz WaterPro RO andPS models. Shipping weight 2 lbs. (0.9 kg)

9113200 WaterPro RO/PS Mobile Stand Adds portability toyour WaterPro RO Station and WaterPro PS PolishingStation. Constructed of glacier white epoxy-coated

steel with 2" diameter hard rubber casters. Includeshardware to mount the WaterPro RO and WaterPro PSback-to-back on the stand. If desired, a single WaterProRO may be mounted on one side or two WaterPro ROStations may be mounted back-to-back. Dimensions(with WaterPro RO Station and WaterPro PS Stationattached): 31 1/8" w x 23 1/2" d x 43 1/2" h (79.1 x59.1 x 110.5 cm). Shipping weight 40 lbs. (18.1 kg)

9077400 Support Stand Forconverting wall-mounted WaterPro ROStations to bench-mounted. Rests on acountertop or otherhorizontal surface.Constructed of glacierwhite epoxy-coatedsteel. Includes hard-ware to mount theWaterPro RO to thestand. Dimensions (with WaterPro ROStation attached): 31 1/8" w x 16 1/8" dx 35 1/3" h (79 x 41 x 90 cm).Shipping weight 20 lbs. (9 kg)


9

Technical Specifications

Inlet Feedwater RequirementsMaximum inlet pressure 100 psiMinimum inlet pressure 30 psiInlet Flow rate 5.5 liters/min.

(1.5 gal./min.)Temperature 10-35° C (50-95° F)pH 4-10Maximum Silt Density Index 5 SDITurbidity ≤ NTULangelier Saturation Index Negative (If positive,

softener pretreatment is required)

Maximum Ion ConcentrationsIron (total) ≤0.1 ppm (mg/liter)Manganese ≤0.1 ppmChlorine ≤0.5 ppm

Typical RO Dispensing Rates*Outlet Flow from RO (valve or gun) Typically 1 liter/

minute at 25° C and conversion rate of approximately 20%

Flow from storage tank 8.7 liters/minute (gravity fed)

Drain Requirement Must handle 5 liters/min.

* depending on feedwater flow rate and pressure


in water level is detected, and two check valves thatdirect water to drain if the water level exceeds normallevel. The tank has a glacier white epoxy-coated steelsupport stand so that it may stand alone up to 6 feetaway from the WaterPro RO Station. For 115 volt, 60Hz, 1 amp operation. Includes an 8-foot, 3-wire cordand plug. Dimensions: 32 7/8" w x 14 3/8" d x 26" h(83.5 x 36.5 x 66 cm). Shipping weight 80 lbs. (36.3 kg)

9100001 70 Liter Storage Tank Same as 9100000 except for 230 volt, 50/60 Hz, 0.5 amp operation. Includes an8-foot, 3-wire cord. An electrical plug is required.

9101000 70 Liter Storage Tank with Dispensing Gun Connectsto the WaterPro RO Station to provide additional stor-age capacity for RO-purified water and means to deliverRO-purified water from four outlets to destinationssuch as a polishing station and glassware washer. Ituses a gravity feed system for water delivery from two3/8" ball valves with 3/8" Celcon female Guest fittings.It uses a 1/4 hp rotary vane pump for 24 psig pressur-ized water delivery to a dispensing gun and a 3//8 NPTfemale port. The dispensing gun includes a 6-foothose, a charcoal epoxy-coated steel gun holder forattachment to the WaterPro RO Station and mountinghardware. The gun permits operation with one handprovides precise drop-by-drop control or locks to pro-vide a continuous stream of water. The pump also pro-vides constant 5.4 liter/minute recirculation of thewater in the tank to minimize bacterial growth. The 70liter polyethylene tank includes 6 feet of polyurethanetubing for connection to the WaterPro RO Station, a0.3 micron vent filter to help prevent airborne bacteri-al contamination of the tank, a float switch to preventthe WaterPro RO Station from overfilling the tank, afill valve wired in series with the float switch that acti-vates when a drop in water level is detected, and twocheck valves that direct water to drain if the waterlevel exceeds normal level. The tank has a glacierwhite epoxy-coated steel support stand so that it maystand alone up to 6 feet away from the WaterPro ROStation. For 115 volt, 60 Hz, 6 amp operation. Includesan 8-foot, 3-wire cord and plug. Dimensions: 32 7/8" wx 14 3/8" d x 26" h (83.5 x 36.5 x 66 cm). Shippingweight 95 lbs. (43 kg)

9113100 Dispensing Gun Provides additional means to dispensewater from the WaterPro RO Station. Trigger permitsoperation with one hand and provides precise drop-

by-drop control or locks to provide a continuousstream of water. Includes gun attached to a 6-foothose, charcoal epoxy-coated steel gun rest and mount-ing hardware. Shipping weight 5 lbs. (2.3 kg)

9100000 70 Liter Storage Tank Connects to the WaterPro ROStation to provide additional storage capacity for RO-purified water and means to deliver RO-purified waterfrom three outlets to destinations such as a polishingstation and glassware washer. It uses a gravity feed sys-

tem for water delivery. The 70 liter polyethylene tankhas one 3/4 NPT female port and two 3/8" ball valveswith 3/8" Celcon* female Guest** fittings. The tankincludes 6 feet of polyurethane tubing for connectionto the WaterPro RO Station, a 0.3 micron vent filter tohelp prevent airborne bacterial contamination of thetank, a float switch to prevent the WaterPro ROStation from overfilling the tank, a fill valve wired inseries with the float switch that activates when a drop


10

Storage Tank Dispensing Rates†

from 3/4 NPT female port up to 26 liters/min. (gravity fed)from one 3/8" ball valve up to 2.1 liters/min. (gravity fed)from both 3/8" ball valves up to 3.6 liters/min. (gravity fed)

(combined rate)Drain Requirement Minimum 1.5 liters/min.

* Celcon® is a registered trademark of Hoechst Celanese.

** John Guest USA, Inc., Wayne, NJ.

† Dispensing rates listed are rates achieved when other ports and/or valves are plugged. Actual rates will vary depending on water demand from other ports and dimensions of fittings and connecting tubing used.


31 ⁄ "1 8

8 ⁄ "5 8

30 ⁄ "3 8

4"

7 ⁄ "23 32

31 ⁄ "1 8

8 ⁄ "5 8

30 ⁄ "3 8 35 ⁄ "1 3

15 ⁄ "7 8

4"

16 ⁄ "1 8

9101001 70 Liter Storage Tank Same as 9101000 except for230 volt, 50/60 Hz, 3 amp operation. Includes an8-foot, 3-wire cord. An electrical plug is required.

† Dispensing rates listed are rates achieved when other ports and/or valves are plugged. Actual rates will vary depending on water demand from other ports and dimensions of fittings and connecting tubing used.


11

WaterPro RO Station

WaterPro RO Station with Optional Support Stand

Storage Tank Dispensing Rates†

from dispensing gun up to 2.0 liters/min. (at 24 psig)from one 3/8" NPT female port up to 6.5 liters/min. (at 24 psig)from one 3/8" ball valve up to 2.1 liters/min. (gravity fed)from both 3/8" ball valves up to 3.6 liters/min. (gravity fed)

(combined rate)Drain Requirement Minimum 1.5 liters/min.

FRONT SIDE

FRONT SIDE

Dimensional Data

Minimum clearance from countertop ▼

Minimum clearance from countertop

▼


WaterPro PS Polishing Stations

12

WaterPro® PS Polishing Stations includeexclusive timed dispensing feature forunattended operation

The WaterPro PS Polishing Stations deliver Type I water*, up to18.2 megohm-cm, from the dispensing valve or optional dispens-ing gun at a typical rate of 1.8 liters per minute depending on feed-water flow rate and pressure, and installed purification modules.

The new control panel includes a timed dispense feature thatallows unattended dispensing of pure water. The risk of overfillingis virtually eliminated because the dispenser shuts off automati-cally once user-set time has elapsed.

The polishing stations have been redesigned into a sleek cabinetfeaturing stainless steel front panel and built-in dispensing centerfor a smaller overall footprint and easier installation. The largecapacity bowls are made of unpigmented virgin naturalpolypropylene, an inert material that will not add impurities tothe water.

Labconco has designed WaterPro PS Stations with the right combina-tions of purification technologies to meet your needs. Choose fromspecialized stations for general chemistry, analytical, life science orcombination usage. In addition, models designed for general chem-istry may be upgraded with additional purification modules at a latertime for use in analytical or life science applications.

Deluxe dispensing gun(Pistol models only)

Attractive and corrosion-resistantType 304 stainless steelfront panel

Mounts on wall orbench with

accessory stand

In-line pressureregulator

Continuous/intermittentrecirculation through

the polishing loop

TOC dump valve(Analytical Instrumentand Hybrid modelsonly)

1/4 hp motor androtary vane

recirculation pump

Full one year warranty

Unpigmented virgin natural polypropylene bowls

Dispensing valve Dual wavelength ultraviolet reactor (Life Science,Analytical Instrumentand Hybrid modelsonly)

UF flush valve (LifeScience and Hybridmodels only)

Built-in ultrafiltermodule (Life Scienceand Hybrid modelsonly)

Water quality alert

Built-in dispensingcenter

Easy installation

User-friendly control panelwith digital display

Timed dispense

•

• • • •

•

••

•

•

•

•

Exclusive feature* Meets ASTM Type I water standard



13

User-friendly control panel with digital display. Touch-padcontrols allow the user to select and view actual water quality(megohm-cm), water temperature (° C), timed dispense (minutes)or resistivity set point (megohm-cm) on the LED display. Pressingthe ON/OFF button to ON lights the LED display. Pressing theON/OFF button to OFF sets continuous recirculation to intermit-tent operation.

Timed dispense for unattended operation. When TIME DISP.is selected, time of water delivery may be set in minutes from 0 to99.9 with the increase/decrease control button. Pressing theDISPENSE button initiates the water delivery from the dispensingvalve. Water delivery automatically ceases when time expires,allowing for unattended operation.

Water quality alert. When SET PT. is selected, resistivity set pointof less than 16 may be selected with the increase/decrease controlbutton. The LED flashes the actual water quality in megohm-cmto alert the user when water quality falls below set point.

Unpigmented virgin natural polypropylene bowls. Bowl materialhas no impurities to contaminate the water ensuring low TOClevels. The large capacity bowls require infrequent cartridgechanges.

Built-in dispensing center. Compact, low profile design incorpo-rates the dispensing center in the polishing station. On Pistol™

models, the dispensing center contains the gun while the dispens-ing valve is located on the polishing station. On models withoutgun, the dispensing center contains the valve. An optional HollowFiber Final Filter may be attached to the valve or gun to removebacteria at the dispensing point.

Attractive and corrosion-resistant Type 304 stainless steelfront panel. The epoxy-coated steel cabinet with stainless steelfront panel houses the pump and motor which are isolated forquiet operation.

Dual wavelength ultraviolet reactor (Life Science, AnalyticalInstrument and Hybrid models only). A UV light with dualwavelengths of 185 and 254 nm ensures both low TOC levelsand bacteria free water.

Built-in ultrafilter module (Life Science and Hybrid modelsonly). A module located in the cabinet houses the ultrafilter,freeing the fourth bowl for an additional deionization cartridge.Additional cartridge capacity allows for less frequent filter changes.

CE marking. All 230 volt, 50 Hz models conform to electricalsafety and electromagnetic compatibility standards as set by theEuropean Community.

Easy installation. Plumbing lines are logically positioned andclearly labeled for mistake-proof installation. Mounts on wall or onbench with accessory support stand.

1/4 hp motor and rotary vane recirculation pump is directlycoupled for quieter operation than smaller gear-type pumps.

In-line pressure regulator protects the system from excessivewater pressure and ensures that inlet water enters the system at opti-mum pressure (up to 100 psi). Feedwater may also be drawn fromnon-pressurized (0 psi) sources such as a reservoir.

Deluxe dispensing gun (Pistol™ models only) gives precise deliverythrough its smooth tip. The gun is attached to a three-foot recircu-lating line for dispensing to bench-level locations. The tip can bedetached and replaced by an optional Hollow Fiber Final Filter toremove bacteria at the dispensing point.

Continuous/intermittent recirculation through the polishingloop maintains water quality, minimizes bacteria growth andreduces rinse up time. Water is produced on demand; no storagetank is used.

TOC dump valve (Analytical Instrument and Hybrid modelsonly) allows a small portion of purified water to drain during inter-mittent recirculation, maintaining ultra low TOC levels below 5ppb and eliminating rinse up times.

UF flush valve (Life Science and Hybrid models only) maintainsultrafilter efficiency. The valve allows a small portion of the puri-fied water to rinse the ultrafilter during intermittent recirculationfor one minute every four hours. Rinsing extends the life of theultrafilter, ensuring pyrogen-free water.

Full one year warranty is provided against defects in materialsand workmanship.

WaterPro PS Pistol Polishing Station 9000501 on Support Stand 9077400WaterPro PS Polishing Station 9000500 on Support Stand 9077400

Exclusive feature


WaterPro PS Polishing Stations/General Chemistry Models

14

Pistol Model Shown

Carbon Cartridge

DeionizationCartridges

Specifications9000500 WaterPro PS Polishing Station with dispensingvalveBowls. 20 1/4" h (51.4 cm). Four bowls constructed of unpigmented virginnatural polypropylene for one carbon and three deionization cartridges.A spanner wrench is provided for filter changes. Cartridges are notincluded. Refer to Polishing Kit 9047101, page 21.Cabinet. 31 1/8" w x 7 23/32" d x 8 5/8" h (79.1 x 19.6 x 21.9 cm).Overall height including bowls: 28 7/8" (73.3 cm). Constructed of epoxy-coated steel with Type 304 stainless steel front panel. Includes 1/4 hpmotor/rotary vane recirculation pump and water pressure regulator.Continuous/Intermittent Recirculation. In the ON setting, the systemcontinuously recirculates through the polishing loop. In the OFF setting,the system automatically starts and circulates water through the polishingloop for approximately 4 minutes every 2 hours to minimize rinse up timeand bacteria growth.Control Panel. Includes ON/OFF switch; LED display; MEG Ω, TEMP. ° C,TIME DISP. and SET PT. indicator lights; DISPENSE switch for water deliv-ery control from valve; MODE switch for selecting LED display; andincrease/decrease switch for setting time from 0 to 99.9 minutes or setpoint from 0 to 16 megohm-cm. Depending on mode selected, LEDdisplay shows actual water quality in megohm-cm, actual water tempera-ture in ° C, dispense time in minutes, or water quality set point inmegohm-cm, and flashes when quality drops below set point.Dispensing Center. Constructed of pressure-formed thermoplastic.Dispensing Valve. Located at the dispensing center, valve typically delivers1.8 liters/minute of Type I water by pressing the DISPENSE switch or acti-vating TIME DISP. Typical dispensing rate with optional Hollow Fiber FinalFilter (not included) is 1.2 liters/minute. If TIME DISP. is activated, waterdispensing from the valve automatically shuts off once user-set time haselapsed.Electrical Requirements. 115 volts, 60 Hz, 7.5 amps AC. Unit includes an8-foot, 3-wire cord and plug.Plumbing Connections. Feedwater line should be 3/8" OD rigid plastictubing or 3/8" ID flexible tubing. Drain port connection to 3/8" OD lineis provided. Shipping weight 60 lbs. (27.2 kg)

9000501 WaterPro PS Pistol Polishing Station withdispensing gun and valveSpecifications are the same as for 9000500 except for the following changes.

Dispensing Gun. Rests in the dispensing center and is attached to a 3-foot(7.6 cm) flexible recirculating line. The hand-held gun typically delivers1.8 liters/minute of Type I water by depressing the trigger. Typical dispens-ing rate with optional Hollow Fiber Final Filter (not included) is 1.2liters/minute.Dispensing Valve. Located on the polishing station.

**9000502 WaterPro PS Polishing Station withdispensing valveSpecifications are the same as for 9000500 except for the following changes.

Agency Approval. Station conforms to European Community electricalsafety and EMC directives and has CE conformity markings.Electrical Requirements. 230 volts, 50 Hz, 4 amps AC.

**9000503 WaterPro PS Pistol Polishing Station withdispensing gun and valveSpecifications are the same as for 9000501 except for the following changes.


* Meets ASTM Type I water standard** International electrical configuration


Carbon FiltrationAn activated carbon filter removes organics and chlorinefrom the feedwater.

DeionizationThree polishing grade mixed bed deionization cartridgesremove inorganic impurities.

Continuous/Intermittent RecirculationMaintains water quality and inhibits bacteria growththroughout the system.

Optional Hollow Fiber Final Filter 9092900Removes bacteria at the dispensing valve or gun. Orderedseparately.

Water Produced: Type I* (up to 18.2 megohm-cm)TOC: <10 ppbTypical Dispensing Rate: 1.8 liters/minuteTypical Dispensing Rate with optional Hollow Fiber Final Filter:1.2 liters/minuteApplications: atomic absorption, flame emission spectroscopy, trace metalanalysis, buffer solutions, standard reagent solutionsTechnologies Used: carbon filtration, deionizationRequired Polishing Kit: 9047101 (one carbon and three deionizationcartridges)


WaterPro PS Polishing Stations/HPLC Analytical Instrument Models

15

Pistol Model Shown

Carbon Cartridge

UltravioletReactor


OrganicAdsorptionCartridge

Specifications9000600 WaterPro PS/HPLC Polishing Station withdispensing valveBowls. 20 1/4" h (51.4 cm). Four bowls constructed of unpigmented virginnatural polypropylene for one carbon, two deionization cartridges and oneorganic adsorption cartridge. A spanner wrench is provided for filterchanges. Cartridges are not included. Refer to Polishing Kit 9047201,page 21.Cabinet. 31 1/8" w x 7 23/32" d x 8 5/8" h (79.1 x 19.6 x 21.9 cm).Overall height including bowls: 28 7/8" (73.3 cm). Constructed of epoxy-coated steel with Type 304 stainless steel front panel. Includes 1/4 hpmotor/rotary vane recirculation pump and water pressure regulator.Continuous/Intermittent Recirculation. In the ON setting, the systemcontinuously recirculates through the polishing loop. In the OFF setting,the system automatically starts and circulates water through the polishingloop for approximately 4 minutes every 2 hours to minimize rinse up timeand bacteria growth.Control Panel. Includes ON/OFF switch; LED display; MEG Ω, TEMP. ° C,TIME DISP. and SET PT. indicator lights; DISPENSE switch for water deliv-ery control from valve; MODE switch for selecting LED display; andincrease/decrease switch for setting time from 0 to 99.9 minutes or setpoint from 0 to 16 megohm-cm. Depending on mode selected, LEDdisplay shows actual water quality in megohm-cm, actual water tempera-ture in ° C, dispense time in minutes, or water quality set point inmegohm-cm, and flashes when quality drops below set point.Dispensing Center. Constructed of pressure-formed thermoplastic.Dispensing Valve. Located at the dispensing center, valve typically delivers1.8 liters/minute of Type I water by pressing the DISPENSE switch or acti-vating TIME DISP. Typical dispensing rate with optional Hollow Fiber FinalFilter (not included) is 1.2 liters/minute. If TIME DISP. is activated, waterdispensing from the valve automatically shuts off once user-set time haselapsed.Electrical Requirements. 115 volts, 60 Hz, 7.5 amps AC. Unit includes an8-foot, 3-wire cord and plug.Plumbing Connections. Feedwater line should be 3/8" OD rigid plastictubing or 3/8" ID flexible tubing. Drain port connection to 3/8" OD lineis provided.TOC Dump Valve. Operates during intermittent recirculation to maintaina low TOC level <5 ppb.Ultraviolet Reactor. Lamp with dual wavelengths of 185 and 254 elimi-nates trace organics and bacteria.Shipping weight 60 lbs. (27.2 kg)

9000601 WaterPro PS/HPLC Pistol Polishing Station withdispensing gun and valveSpecifications are the same as for 9000600 except for the following changes.

Dispensing Gun. Rests in the dispensing center and is attached to a 3-foot(7.6 cm) flexible recirculating line. The hand-held gun typically delivers 1.8liters/minute of Type I water by depressing the trigger. Typical dispensing ratewith optional Hollow Fiber Final Filter (not included) is 1.2 liters/minute.Dispensing Valve. Located on the polishing station.

**9000602 WaterPro PS/HPLC Polishing Station withdispensing valveSpecifications are the same as for 9000600 except for the following changes.


**9000603 WaterPro PS/HPLC Pistol Polishing Station withdispensing gun and valveSpecifications are the same as for 9000601 except for the following changes.




Carbon FiltrationAn activated carbon filter removes organics and chlorinefrom the feedwater.

DeionizationTwo polishing grade mixed bed deionization cartridgesremove inorganic impurities.

Organic AdsorptionAn organic adsorption cartridge removes trace organics.

Ultraviolet ReactorUV light with dual wavelengths of 185 and 254 nm ensureslow TOC and bacteria levels.

TOC Dump ValveDirects a small portion of purified water to drain duringintermittent recirculation, to maintain low TOC values.

Continuous/Intermittent RecirculationMaintains water quality and inhibits bacteria growththroughout the system.

Optional Hollow Fiber Final Filter 9092900Removes bacteria at the dispensing valve or gun. Orderedseparately.

Water Produced: Type I* (up to 18.2 megohm-cm)TOC: <5 ppbTypical Dispensing Rate: 1.8 liters/minuteTypical Dispensing Rate with optional Hollow Fiber Final Filter:1.2 liters/minuteApplications: HPLC, electrophoresis and fluoroscopy analysisTechnologies Used: carbon filtration, deionization, organic adsorption,ultraviolet exposureRequired Polishing Kit: 9047201 (one carbon, two deionization and oneorganic adsorption cartridges)


WaterPro PS Polishing Stations/UF Life Sciences Models

16

Pistol Model Shown

Carbon Cartridge

Specifications9000700 WaterPro PS/UF Polishing StationBowls. 20 1/4" h (51.4 cm). Four bowls constructed of unpigmented virginnatural polypropylene for one carbon and three deionization cartridges. Aspanner wrench is provided for filter changes. Cartridges are not included.Refer to Polishing Kit 9047101, page 21.Cabinet. 31 1/8" w x 7 23/32" d x 8 5/8" h (79.1 x 19.6 x 21.9 cm).Overall height including bowls: 28 7/8" (73.3 cm). Constructed of epoxy-coated steel with Type 304 stainless steel front panel. Includes 1/4 hpmotor/rotary vane recirculation pump and water pressure regulator.Continuous/Intermittent Recirculation. In the ON stetting, the systemcontinuously recirculates through the polishing loop. In the OFF setting,the system automatically starts and circulates water through the polishingloop for approximately 4 minutes every 2 hours to minimize rinse up timeand bacteria growth.Control Panel. Includes ON/OFF switch; LED display; MEG Ω, TEMP. ° C,TIME DISP. and SET PT. indicator lights; DISPENSE switch for water deliv-ery control from valve; MODE switch for selecting LED display; andincrease/decrease switch for setting time from 0 to 99.9 minutes or setpoint from 0 to 16 megohm-cm. Depending on mode selected, LEDdisplay shows actual water quality in megohm-cm, actual water tempera-ture in ° C, dispense time in minutes, or water quality set point inmegohm-cm, and flashes when quality drops below set point.Dispensing Center. Constructed of pressure-formed thermoplastic.Dispensing Valve. Located on the dispensing center, valve typicallydelivers 1.1 liters/minute of Type I, pyrogen-free water by pressing theDISPENSE switch or activating TIME DISP. Typical dispensing rate withoptional Hollow Fiber Final Filter (not included) is 1.0 liter/minute. IfTIME DISP. is activated, water dispensing from the valve automaticallyshuts off once user-set time has elapsed. Electrical Requirements. 115 volts, 60 Hz, 7.5 amps AC. Unit includes an8-foot, 3-wire cord and plug.Plumbing Connections. Feedwater line should be 3/8" OD rigid plastictubing or 3/8" ID flexible tubing. Drain port connection to 3/8" OD lineis provided.Ultrafilter and Flush Valve. One ultrafilter is included. Valve operatesduring intermittent recirculation to maintain ultrafilter efficiency.Ultraviolet Reactor. Lamp with dual wavelengths of 185 and 254 nmeliminates trace organics and bacteria.Shipping weight 60 lbs. (27.2 kg)

9000701 WaterPro PS Pistol Polishing Station withdispensing gun and valveSpecifications are the same as for 9000700 except for the following changes.

Dispensing Gun. Rests in the dispensing center and is attached to a 3-foot(7.6 cm) flexible recirculating line. The hand-held gun typically delivers1.1 liters/minute of Type I, pyrogen-free by depressing the trigger. Typicaldispensing rate with optional Hollow Fiber Final Filter (not included) is1.0 liter/minute.Dispensing Valve. Located on the polishing station.

**9000702 WaterPro PS Polishing Station withdispensing valveSpecifications are the same as for 9000700 except for the following changes.


**9000703 WaterPro PS Pistol Polishing Station withdispensing gun and valveSpecifications are the same as for 9000701 except for the following changes.



Purification Technologies/Features:Carbon FiltrationAn activated carbon filter removes organics and chlorinefrom the feedwater.DeionizationThree polishing grade mixed bed deionization cartridgesremove inorganic impurities.UltrafiltrationAn ultrafilter removes all particles, microorganisms and pyro-gens greater than 0.01 micron in diameter (10,000 Daltoncut-off).Utrafilter Flush ValveDirects a small portion of purified water to drain duringintermittent recirculation, to maintain ultrafilter efficiency.Ultraviolet ReactorUV light with dual wavelengths of 185 and 254 nm ensureslow TOC and bacteria levels.Continuous/Intermittent RecirculationMaintains water quality and inhibits bacteria growththroughout the system.Optional Hollow Fiber Final Filter 9092900Removes bacteria at the dispensing valve or gun. Orderedseparately.

Water Produced: Type I* (up to 18.2 megohm-cm), pyrogen-free to0.06 eu/mlTOC: <10 ppbTypical Dispensing Rate: 1.1 liters/minuteTypical Dispensing Rate with optional Hollow Fiber Final Filter:1.0 liter/minuteApplications: cell culture, clinical and life scienceTechnologies Used: carbon filtration, deionization, ultrafiltration,ultraviolet exposureRequired Polishing Kit: 9047101 (one carbon and three deionizationcartridges)


Ultrafilter

UltravioletReactor


WaterPro PS Polishing Stations/HPLC/UF Hybrid Models

17

Specifications9000704 WaterPro PS HPLC/UF Hybrid Polishing Stationwith dispensing gun and valveBowls. 20 1/4" h (51.4 cm). Four bowls constructed of unpigmented virginnatural polypropylene for one carbon, two deionization and one organicadsorption cartridges. A spanner wrench is provided for filter changes.Cartridges are not included. Refer to Polishing Kit 9047201, page 21.Cabinet. 31 1/8" w x 7 23/32" d x 8 5/8" h (79.1 x 19.6 x 21.9 cm). Overallheight including bowls: 28 7/8" (73.3 cm). Constructed of epoxy-coatedsteel with Type 304 stainless steel front panel. Includes 1/4 hpmotor/rotary vane recirculation pump and water pressure regulator.Continuous/Intermittent Recirculation. In the ON setting, the systemcontinuously recirculates through the polishing loop. In the OFF setting,the system automatically starts and circulates water through the polishingloop for approximately 4 minutes every 2 hours to minimize rinse up timeand bacteria growth.Control Panel. Includes ON/OFF switch; LED display; MEG Ω, TEMP. ° C,TIME DISP. and SET PT. indicator lights; DISPENSE switch for water deliv-ery control from valve; MODE switch for selecting LED display; andincrease/decrease switch for setting time from 0 to 99.9 minutes or setpoint from 0 to 16 megohm-cm. Depending on mode selected, LEDdisplay shows actual water quality in megohm-cm, actual water tempera-ture in ° C, dispense time in minutes, or water quality set point inmegohm-cm, and flashes when quality drops below set point.Dispensing Center. Constructed of pressure-formed thermoplastic.Dispensing Gun. Rests in dispensing center and is attached to a 3-foot(7.6 cm) flexible recirculating line. The hand-held gun typically delivers1.1 liters/minute of Type I, pyrogen-free water by depressing the trigger.Typical dispensing rate with optional Hollow Fiber Final Filter (not included)is 1.0 liter/minute.Dispensing Valve. Located on the polishing station, valve typically delivers1.8 liters/minute of Type I by pressing the DISPENSE switch or activatingTIME DISP. Typical dispensing rate with optional Hollow Fiber Final Filter(not included) is 1.1 liters/minute. If TIME DISP. is activated, water dis-pensing from the valve automatically shuts off once user-set time haselapsed.Electrical Requirements. 115 volts, 60 Hz, 7.5 amps AC. Unit includes an8-foot, 3-wire cord and plug.Plumbing Connections. Feedwater line should be 3/8" OD rigid plastictubing or 3/8" ID flexible tubing. Drain port connection to 3/8" OD lineis provided.Ultrafilter and Ultrafilter Flush/TOC Dump Valve. One ultrafilter isincluded. Valve operates during intermittent recirculation to maintain alow TOC level <5 ppb and ultrafilter efficiency.Ultraviolet Reactor. Lamp with dual wavelengths of 185 and 254 nmeliminates trace organics and bacteria.Shipping weight 60 lbs. (27.2 kg)

**9000705 WaterPro PS HPLC/UF Hybrid Polishing Stationwith dispensing gun and valveSpecifications are the same as for 9000704 except for the following changes.



Purification Technologies/Features:Carbon FiltrationAn activated carbon filter removes organics and chlorinefrom the feedwater.DeionizationTwo polishing grade mixed bed deionization cartridgesremove inorganic impurities.Organic AdsorptionAn organic adsorption cartridge removes trace organics.UltrafiltrationAn ultrafilter removes all particles, microorganisms andpyrogens greater than 0.01 micron in diameter (10,000Dalton cut-off).Ultrafilter Flush/TOC Dump ValveFlushes the ultrafilter membrane and directs a small portionof purified water to drain during intermittent recirculation, tomaintain ultrafilter efficiency and low TOC values.Ultraviolet ReactorUV light with dual wavelengths of 185 and 254 nm ensureslow TOC and bacteria levels.Continuous/Intermittent RecirculationMaintains water quality and inhibits bacteria growththroughout the system.Optional Hollow Fiber Final Filter 9092900Removes bacteria at the dispensing valve or gun. Orderedseparately.

Water Produced: Type I* (up to 18.2 megohm-cm) from valve, Type Ipyrogen-free to 0.06 eu/ml from gunTOC: <5 ppb (from valve)Typical Dispensing Rate: 1.8 liters/minute through valve,1.1 liters/minute through gunTypical Dispensing Rate with optional Hollow Fiber Final Filter:1.1 liter/minute through valve, 1.0 liter/minute through gunApplications: HPLC and other instrument analyses, life science applicationsTechnologies Used: carbon filtration, deionization, organic adsorption,ultrafiltration, ultraviolet exposureRequired Polishing Kit: 9047201 (one carbon, two deionization and oneorganic adsorption cartridges)

Carbon Cartridge

UltrafilterDeionizationCartridges

OrganicAdsorptionCartridge

UltravioletReactor



18

Rigorous testing has been conducted on WaterPro PS PolishingStations to ensure that high purity water is delivered. The chartsand technical specifications given below, which represent actualtest results, show that water produced by the WaterPro PS meets orexceeds standards set by the ASTM.

ICP/MS Analysis

(Models 9000500, 9000501, 9000502, 9000503, 9000600,9000601, 9000602, 9000603, 9000704*, 9000705*)

Element ppb Element ppb

Al <0.07 Mo <0.02Sb <0.02 Nd <0.02As <0.2 Ni 0.06Ba <0.01 Nb <0.02Be <0.04 Os <0.02Bi <0.04 Pb <0.06B <0.5 Pt <0.08Cd <0.03 Pr <0.01Ca <5 Re <0.06Ce <0.01 Ph <0.02Cs <0.02 Rb <0.01Cr 0.08 Ru <0.05Co <0.01 Sm <0.04Cu 0.1 Sc <0.05Dy <0.04 Se <7Er <0.02 Ag <0.03Eu <0.02 Na 0.11Gd <0.04 Sr <0.01Ga <0.04 Ta <0.02Ge <0.05 Te <0.04Au <0.05 Tb <0.02Hf <0.03 Tl <0.05Ho <0.01 Th <0.02In <0.02 Tm <0.01Ir <0.06 Sn <0.02Fe <0.2 Ti <0.05La <0.01 W <0.01Pb <0.05 U <0.02Li <0.03 V <0.03Lu <0.01 Yb <0.03Mg <0.02 Y <0.02Mn 0.05 Zn <0.05Hg <0.05 Zr <0.01

Anions ppb

F 0.033Cl 0.85NO2 <0.05HPO4 NDBr NDNO3 <0.025SO4 0.046CH3CO2 0.073CH3SO3 NDHCO2 0.096C2O4 <0.025

Cations ppb

Li NDNa NDNH4 0.025K ND

Ion Chromatography

(Models 9000500, 9000501, 9000502, 9000503, 9000600,9000601, 9000602, 9000603, 9000704*, 9000705*)

ND = not detectable* from dispensing valve

Technical Specifications –Type I Water

BacteriaGeneral Chemistry and Analytical <1 cfu/ml (with optional Hollow Instrument models Fiber Final Filter installed)

Life Science and Hybrid models <1 cfu/100 ml

Silicate Not detectable

Specific Resistance Up to 18.2 megohm-cm at 25° C

Particulate Matter None

TOC (General Chemistry and Life Science Models 9000500, <10 ppb9000501, 9000502, 9000503, 9000700, 9000701, 9000702, and 9000703)

TOC (Analytical Instrument and Hybrid Models 9000600, 9000601, <5 ppb9000602, 9000603, 9000704, and9000705)

Pyrogens (Life Science Pyrogen-free to 0.06 eu/mland Hybrid Models 9000700, Typical 3x log reduction9000701, 9000702, 9000703 and 9000704 and 9000705 from gun)

Water Standards Meets or exceeds ASTM andNCCLS Type I specifications

Typical PS Dispensing Rates*General Chemistry and Analytical 1.8 liters/minuteInstrument models 1.2 liters/minute (with optional

Hollow Fiber Final Filter installed)Life Science models 1.1 liters/minute

1.0 liter/minute (with optional Hollow Fiber Final Filter installed)

Hybrid models 1.8 liters/minute through valve1.1 liters/minute through valve (with optional Hollow Fiber Final Filter installed)1.1 liters/minute through gun1.0 liter/minute through gun (with optional Hollow Fiber Final Filter installed)

Inlet Feedwater RequirementsMinimum Inlet Flow Rate 2 liters/minuteWater Purity 100 µs conductivity or betterMinimum Pressure 0 psiMaximum Pressure 100 psiTemperature 4-30° C (40-83° F)pH 4-10

*depending on feedwater flow rate and pressure



19

Expendables

9047101 General Chemistry/UF Polishing Kit.(Required for Models 9000500, 9000501, 9000502, 9000503,9000700, 9000701, 9000702 and 9000703). Includes ActivatedCarbon Cartridge (1), polishing grade mixed bed DeionizationCartridges (3). Shipping weight 9.5 lbs. (4.3 kg)

9047201 HPLC/Hybrid Polishing Kit.(Required for Models 9000600, 9000601, 9000602, 9000603,9000704 and 9000705). Includes Activated Carbon Cartridge (1),polishing grade mixed bed Deionization Cartridges (2), andOrganic Adsorption Cartridge (1). Shipping weight 9.5 lbs. (4.3 kg)

9007201 Activated Carbon Cartridge. Shipping weight 4 lbs. (1.8 kg)

9007301 Deionization Cartridge, Polishing grade mixed bed to deliver 18.2 megohm-cm qualitywater with TOC levels below 5 ppb. Shipping weight 4 lbs. (1.8 kg)

9053300 Organic Adsorption Cartridge.Shipping weight 4 lbs. (1.8 kg)

9104400 Replacement Ultrafilter,Spiral-wound, polysulfone membrane.Shipping weight 3 lbs. (1.4 kg)

9109200 Replacement UV Lamp,185 and 254 nanometers. Labconco recommends annual UV lampreplacement. Shipping weight 0.5 lb. (0.2 kg)

9092900 Hollow Fiber Final Filter, self-venting.Optional filter attaches to the dispensing valve or gun. Removesall particulates and bacteria that are larger than 0.2 micron indiameter. Shipping weight 0.5 lb. (0.2 kg)

Accessories

9113200 WaterPro RO/PS Mobile Stand Adds portability to yourWaterPro RO Station and WaterPro PS Polishing Station.Constructed of glacierwhite epoxy-coatedsteel with 2" diameterhard rubber casters.Includes hardware tomount the WaterProRO and WaterPro PSback-to-back on thestand. If desired, asingle WaterPro PSmay be mounted onone side or twoWaterPro PS stationsmay be mountedback-to-back.Dimensions (withWaterPro RO Stationand WaterPro PS Station attached): 31 1/8" w x 23 1/2" d x 43 1/2 " h(79.1 x 59.1 x 110.5 cm). Shipping weight 40 lbs. (18.1 kg)

9077400 Support Stand.Optional stand rests on countertop or other horizontal surfacewhen benchtop mounting is preferred. Constructed of glacierwhite epoxy-coatedsteel. Dimensions(with WaterPro PSPolishing Stationattached): 31 1/8" w x16 1/8" d x 35 1/3" h(79 x 41 x 90 cm).Shipping weight20 lbs. (9.1 kg)

9109300 Analytical Instrument Model Conversion Kit.Includes the UV Lamp, TOC Flush Valve and hardware necessaryto convert a WaterPro PS General Chemistry model to a WaterProPS/HPLC Analytical Instrument model. Shipping weight 1.5 lbs.(0.7 kg)

9109400 Life Science Model Conversion Kit. Includes the Ultrafilter, UV Lamp, Ultrafilter Flush Valve and hard-ware necessary to convert a WaterPro PS General Chemistry modelto a WaterPro PS/UF Life Science model. Shipping weight 2.6 lbs.(1.2 kg)



20

31 ⁄ "1 8

8 ⁄ "5 8

20 ⁄ "1 4

4"

7 ⁄ "23 32

8 ⁄ "5 8

20 ⁄ "1 4

4"

31 ⁄ "1 8 7 ⁄ "23 32

Minimum clearance from countertop▼

Minimum clearance from countertop▼

FRONT SIDE

WaterPro PS Polishing Station with Dispensing Valve

FRONT SIDE

DispensingValve

FeedwaterInlet

Drain

DispensingValve

DispensingGun

FeedwaterInlet

Drain

Dimensional Data


Companion Products

1

The WaterPro RO Station and 70 Liter Storage Tank may be plumbed to the SteamScrubber®, FlaskScrubber® orFlaskScrubber® Vantage® Series Laboratory Glassware Washer to provide purified water for up to six rinses. ContactLabconco at 800-821-5525 or 816-333-8811 for more information.


labconco waterpro water purification systems

Documents