measuring - marking · measuring - marking angle measurer 58 ... waterline marker 62 wiggler &...

CONTENTS

RULES

DAVID USE PHOTO

SD0010

MEASURING - MARKING

ANGLE MEASURER 58AUTOMATIC CENTRE PUNCH/SCRIBES 66BEVELLED STRAIGHT EDGE 58BORE GAUGES 61CALIPERS & DIVIDERS 63CALIPER GAUGES 59CENTRE PUNCHES 66CENTRE SQUARES 65DEPTH GAUGES 58DRIVE PIN VICES 67 - 68ELECTRONIC CALIPER GAUGES 60ENGINEERS MARKING GAUGE 65ENGINEERS MINI LEVELS 63ENGINEERS BLUE 67ENGINEERS SQUARES 64 - 65FEELER GAUGES 59FLAT SQAURES 64HELPING HANDS 70INCLINOMETER 70LETTER & NUMBER STAMPS 68MAGNETIC BASES & DIAL GAUGES 61 - 62MEASURING SETS 61MEASURING WHEELS 70MICROMETERS 60 - 61MINI TABLE LAMP MAGNIFIER 70ODDLEG CALIPERS 64OPTICAL CENTRE PUNCH 67PROTRACTORS 58RADIUS GAUGES 58RULES 56 - 57RULER STOP 57SCALE RULES 57SCRIBES 65 - 66SLATERS TRACK GAUGE 69SPRING BALANCES 69SURFACE GAUGES 63SURFACE PLATE 63TELESCOPIC GAUGE SET 61TOOL MAKERS CLAMPS 69TRANSFER PUNCHES 67UNIVERSAL BEVEL PROTRACTOR........... 69V-BLOCK & CLAMP 69WATERLINE MARKER 62WIGGLER & CENTRE FINDER SET 62WIRE GAUGE 69

CALIPER GAUGES

MICROMETERS

DAVID USE PHOTO

SD0010

SCRIBES

DAVID USE PHOTO

SD0010

CENTRE PUNCHES

DAVID USE PHOTO

SD0010

55Last Revised 26/10/2011

RULES

STAINLESS STEEL RULES a range of high quality stainless steelrules. Easy to read permanently etched graduations showingmetric graduations of ½mm, mm, cm and imperial graduations of1/16, 1/32 and 1/64". Metric/Imperial conversion tables are etchedon the reverse side. Lengths 6", 12", 24" and 39".

CODE TYPE PRICE040-551 L/C Stainless Steel Rule 6".................................. £1.50040-552 L/C Stainless Steel Rule 12"................................ £2.99040-553 L/C Stainless Steel Rule 24"................................ £5.99040-554 L/C Stainless Steel Rule 39"................................ £11.99

FISHER STAINLESS STEEL RULES manufactured from highquality stainless steel. Permanently etched graduations show met-ric graduations of ½mm, mm, cm and imperial graduations of 1/16,1/32 and 1/64". Lengths 6", 12", 24" and 39".

CODE TYPE PRICERLSS06 Fisher Stainless Steel Rule 6".............................. £2.50RLSS12 Fisher Stainless Steel Rule 12"............................ £3.99RLSS24 Fisher Stainless Steel Rule 24"............................ £7.99RLSS39 Fisher Stainless Steel Rule 39"............................ £15.99

FISHER SATIN CHROME STAINLESS STEEL RULES manufac-tured in Japan from high quality hardened stainless steel. Thesatin chrome finish is an ideal surface for printing fine graduationswhich are easy to read with minimum light reflection. The rulershows metric graduations of ½mm, mm, cm and imperial gradua-tions of 1/10, 1/16, 1/20, 1/32, 1/50 and 1/64". 6", 12" and 24".

CODE TYPE PRICERLFC06 Fisher Satin Chrome Rule 6"................................ £3.99RLFC12 Fisher Satin Chrome Rule 12".............................. £7.99RLFC24 Fisher Satin Chrome Rule 24".............................. £18.99

ALUMINIUM RULES anodised aluminium rule with easy to readmarkings on both sides. Metric showing graduations of mm andcm, imperial graduations of 1/16, 1/4, 1/2 and 1". Available in 6".Made in England.

CODE TYPE PRICE040-070 Aluminium Rule 6"................................................ £1.79

FLEXIBLE STEEL RULES a range of flexible stainless steel ruleswhich are useful for measuring curved surfaces. The rules havepermanently etched marking showing metric graduations of mmand cm, imperial graduations of 1/16, 1/32, 1/2 and 1".

CODE TYPE PRICE040-013 Flexible Stainless Steel Rule 6"............................ £2.50040-014 Flexible Stainless Steel Rule 12".......................... £4.50

STAINLESS STEEL CENTRE RULES a high quality centring rulewith permanently etched imperial graduations. The rules aremarked on one face only with scales of 6" - 0 - 6"/12" - 0 - 12"graduated in 32nds on one edge, 0 - 12"/0 - 24" graduated in16ths on the other. Useful when marking out and can also beused as a right/left hand reading rule. Available in 12" and 24".

CODE TYPE PRICERLCF12 Centre Rule 12".................................................... £5.99RLCF24 Centre Rule 24".................................................... £11.99

WIDE PATTERN ALUMINIUM RULE a useful lightweight alumini-um rule for use in the workshop, home or drawing office. The ruleis graduated in centimetres and millimetres on one edge and inch-es and sixteenths on the other. Length 600mm long, 50 mm wideand has a hanging hole at one end.

CODE TYPE PRICE040-113 Wide Pattern Aluminium Rule 60cm..................... £6.50

FISHER FOLDING RULES a folding rule with permanently etchedmarkings. The rule folds in half pivoting on a strong rivet. The rulehas pressed indentations, these serve to hold the rule straightwhen extended. The rules have metric and imperial scales, gradu-ated in mm and cm on one side, 1/16, 1/4, 1/2 and 1" on thereverse side. Length overall 24", available in steel or stainlesssteel.

CODE TYPE PRICE040-126 Fisher Stainless Steel Folding Rule 24"............... £7.99

EASY ANGLE PROTRACTOR RULER a heavy duty foldablesteel protractor ruler with metric and imperial graduations. It is ,adjustable through 360° and has an integrated angle finder foreasy angle measuring. It is fitted with a tightening screw to lockangle in place for repated measurements.

CODE TYPE PRICE040-421 Easy Angle Protractor Ruler 600mm.................... £4.99

FOLDING RULES two types of these useful rules are available, aplastic type manufactured from tough impact resistant ABS plasticwith clear graduations of mm/cm on one side, imperial on the othergraduated in 1/8". The hardwood folding rule has black gradua-tions and solid brass hinges and tips. Metric on one side showingcm, mm. Imperial on the reverse showing inches and 1/8". Lengthoverall 1M/39",folding downto 10½".

CODE TYPE PRICE12392 Plastic Folding Rule 39"....................................... £9.5036522 Hardwood Folding Rule 39".................................. £11.99

SQUIRES MODEL & CRAFT TOOLS

SQUIRES TEL. 01243 842424 - FAX. 01243 84252556


E-mail: sales@squirestools .com - www.squirestools .com 57

POCKET RULE WITH CLIP a 150mm stainless steel rule withmetric and imperial graduations. Fitted a pocket clip/sliding depthgauge.

CODE TYPE PRICE040-611 S/L Pocket Rule with Pocket Clip/Depth Gauge... £1.99

RULE WITH DRILL GAUGE a 150mm stainless steel rule withmetric and imperial graduations. This rule also features a series ofholes 1/16" - 1/4", ideal for identifying drill sizes etc.

CODE TYPE PRICE040-959 Stainless Steel Rule 150mm with Drill Gauge...... £1.99

FLAT MARKING OUT RULER/SQUARE a one piece flat squareuseful for measuring and marking out on flat material such as foamboard and polystyrene sheet. The square is steel with a black fin-ish and has metric and imperial markings. Although not a preci-sion tool, it isuseful additionto the modellerswork bench.Dims:-200 x 300mm.

CODE TYPE PRICE040-894 L/C Flat Marking Out Ruler/Square 200x300mm. £4.50

ADJUSTABLE T SQUARE 24'' made from a light alloy steel, canbe used for measuring various angles and is ideal for woodworkingand many other marking out applications. Size 660mm x 360mm.

CODE TYPE PRICE160-211 Adjustable T Square 24''/600mm.......................... £8.99

SCALE RULES

PECO N SCALE RULE a handy stainless steel rule useful for allBritish N Gauge modellers. It carries markings showing the correctmeasurements up to 50ft for British N Scale (1:148), ideal forscratch building, kit building and for measuring scale distances onthe layout. The correct coupling height for PECO N gauge rollingstock is also shown, along with a track centre guide for postioningmultiple trackformations.

CODE TYPE PRICE040-002 Peco N Scale Rule............................................... £3.99

STAINLESS STEEL SCALE RULES a range of flat profile stain-less steel scale rules covering a range of popular modelling scales.All types have permanently etched markings on a satin finish. Thereverse side of all types has a range of conversion tables coveringinches to mm, metric tapping drill sizes, BA tapping and clearancesizes. All rules are 12".

CODE TYPE PRICE040-102 S/Steel Scale Rule 2mm/Foot - N Gauge............. £3.99040-103 S/Steel Scale Rule 3.5mm/Foot - HO Gauge....... £3.99040-104 S/Steel Scale Rule 4mm/Foot - OO Gauge.......... £3.99040-107 S/Steel Scale Rule 7mm/Foot - O Gauge............. £3.99040-112 S/Steel Scale Rule 1"/Foot - 1/12th Scale............ £3.99040-128 S/Steel Scale Rule 1/2"/Foot - 1/24th Scale......... £3.99040-135 S/Steel Scale Rule 1/35th - Military Modelling...... £3.99040-172 S/Steel Scale Rule 1/72nd - Military Modelling..... £3.99

STAINLESS STEEL SCALE RULE a flat profile stainless steelscale rule with 1/12th and 1/24th permanently etched markings.The 1/24th edge features a centre 0. Length 12".

CODE TYPE PRICE040-241 S/Steel Scale Rule 1/12th - 1/24th Scale............. £3.99

SCALE RULES a range high quality aluminium scale rules. Thesection of the rule is triangular allowing six working edges for thevarious scales. This arrangement allows a clear, uncluttered scaleto be read. 2 types are available:- Metric showing 1:100, 1:200,1:300, 1:400, 1:500 and 1:600. The imperial scales read 1:12,1:24, 1:35, 2mm =1 foot,4mm = 1 foot and 7mm = 1foot.

CODE TYPE PRICERL1001 Scale Rule Metric 15cm........................................ £5.89RL1002 Scale Rule Metric 30cm........................................ £14.99RL1003 Scale Rule Imperial 15cm..................................... £5.99

TRIANGULAR SCALE RULE METRIC a high quality aluminiummetric scale rule. The section of the rule is triangular allowing sixworking edges for the various scales. This arrangement allows aclear, uncluttered scale to beread. 1:20, 1:25, 1:50, 1:75,1:100 and 1:125.Length 30cm.

CODE TYPE PRICE041-125 Triangular Scale Rule Metric 30cm...................... £2.99

RULER STOP

RULER STOP a handy tool machined from steel with a knurledbrass nut. The Rule Stop will fit onto virtually any standard steelrule between 8mm(5/16") and 32mm(1-1/4") wide. It clamps firmlyand square to the rule by virtue of an internal dovetail face and finemachining. It turns thehumble steel rule into adepth gauge, a transfergauge and small square.

CODE TYPE PRICE040-047 Ruler Stop............................................................. £5.99


SQUIRES TEL. 01243 842424 - FAX. 01243 84252558

BEVELLED STRAIGHT EDGE

BEVELLED STRAIGHT EDGE a top quality steel workshopstraight edge used for cutting thin material such as card andveneer and for checking the straightness of lengths of timber,machine tables, plane soles etc. It is 38mm wide and 5mm thickand ground on all surfaces for accuracy. Length 450mm.

CODE TYPE PRICE040-350 Bevelled Straight 450mm..................................... £11.99

"PERFECT MARKER" TRAMMEL POINTS ideal for marking outand layout work. Secures easily to most standard spirit levels,used for marking and scribing circles and radi.

CODE TYPE PRICE160-185 "Perfect Marker" Trammel Points........................ £2.99

DEPTH GAUGES

DEPTH GAUGE a 6"/150mm depth gauge with permanentlyetched graduations on the rule. The metric and imperial scales areon opposite sides, the rule is easily turned over in the depth stopwhich can belocked inposition.

CODE TYPE PRICEDG0010 Depth Gauge 6"/150mm....................................... £4.99

DIGITAL DEPTH GAUGE a digital depth gauge ideal for checkingtyres, brake shoes and hole depths. It has a 0.01mm resolutionand metric and imperialmodes. With a clear LCDdisplay and measuringrange of 0 - 25mm.Requires 1 x CR2032battery (not supplied).

CODE TYPE PRICE040-085 Digital Depth Gauge 0 - 25mm............................. £11.99

PROTRACTORS

STAINLESS STEEL PROTRACTOR a stainless steel protractorwith permanently etched graduations on the plate and ruler. Theprotractor plate is graduated 0-180° in opposite directions, the bot-tom edge of the plate also has a metric scale. The rule is marked0 - 100mm in mm graduations. The rule can be locked in position.Plate dims:-90 x 50mm.

CODE TYPE PRICE040-015 Stainless Steel Protractor..................................... £5.99

DEPTH GAUGE PROTRACTOR a stainless steel protractor with adepth gauge rule. The protractor plate is graduated 0-180° inopposite directions, the 6" depth gauge rule can be locked in posi-tion, and is graduated in metric and imperial. All graduations arepermanentlyetched. Platedims:- 3½" x 2".

CODE TYPE PRICEPRDG20 Depth Gauge Protractor....................................... £8.99

ANGLE MEASURER

ANGLE MEASURER a simple device that gives a direct reading ofcorner angles in the range 25° to 165° and it also gives an auto-matic readout of the half angle needed for cutting mitre joints. It ismanufactured with anodised aluminium arms with clear anglemarkings. Length overall 380mm.

CODE TYPE PRICE040-111 Angle Measurer 25° to 165°................................. £7.99

RADIUS GAUGES

L/C METRIC RADIUS GAUGES a range of economically pricedradius gauges with folding leaves and accurately formed concaveand convex radii for fast, positive identification of various radii.The blades are individually stamped.

CODE TYPE PRICE040-609 L/C Radius Gauge 1 - 7mm.................................. £6.55040-569 L/C Radius Gauge 7.5 - 15mm............................. £8.99040-610 L/C Radius Gauge 15.5 - 25mm........................... £9.99

RADIUS GAUGE with folding leaves and accurately formed con-cave and convex radii for fast, positive identification of variousradii. The blades are individually stamped. Manufactured in .0 -3mm in 0.25mm increments and 3.5 to 7mm in 0.50mm incre-ments. Made in Germany.

CODE TYPE PRICE040-125 Radius Gauge....................................................... £12.99

WHEN PLACING AN ORDER PLEASE USE THE FULL ORDER CODE



FEELER GAUGES

FEELER GAUGE SETS with 100mm long taper blades. Eachblade is marked with its size and folds into a plated steel case withthumbscrew. Metric set contains:-0.05, 0.10, 0.15, 0.20,0.30, 0.40, 0.50, 0.60,0.70 & 0.80mm.

Imperial set contains:-0.0015, 0.002, 0.003,0.004, 0.006, 0.008,0.010, 0.012, 0.015& 0.025".

CODE TYPE PRICE73988 Feeler Gauge Set Met 10 Blades 0.05 - 0.80mm. £3.1973970 Feeler Gauge Set Imp 10 Blades 0.0015 - 0.025" £3.19

FEELER GAUGE SETS expert quality, 100mm long taper blades,hardened and polished for long accurate life. Each blade ismarked with its size and folds into a polished steel case withthumbscrew.Metric set contains:-0.05, 0.10, 0.15, 0.20, 0.25,0.30, 0.35, 0.40, 0.45, 0.50,0.55, 0.60, 0.65, 0.70, 075,0.80, 0.90, 0.95 & 1.0mm.Imperial set contains:-0.0015, 0.002, 0.0025, 0.003,0.004, 0.005, 0.006, 0.007,0.008, 0.009, 0.010, 0.011,0.012, 0.013, 0.014, 0.015,0.016, 0.017, 0.018, 0.019,0.020, 0.021, 0.022, 0.023,0.024 & 0.025".

CODE TYPE PRICE73996 Feeler Gauge Set Met 20 Blades 0.05-1.0mm..... £7.4910286 Feeler Gauge Set Imp 26 Blades 0.0015-0.025... £11.99

COMBINATION FEELER GAUGE an expert quality, one piececombination gauge with 32 dual marked blades 95mm long, hard-ened for long accurate life. Each blade is marked with its size andfolds into a polished steel case with thumbscrew. Metric 0.03 -1.0mm. Imperial 0.001 - 0.040".Metric:-0.03, 0.04, 0.05, 0.06,0.07, 0.08, 0.09, 0.10, 0.13,0.15, 0.18, 0.20, 0.23, 0.25,0.28, 0.30, 0.33, 0.35, 0.40,0.45, 0.50, 0.55, 0.60, 0.63,0.65, 0.70, 075, 0.80, 0.85,0.90 & 1.0mm.Imperial:-0.001, 0.0015, 0.002,0.0025, 0.0028, 0.003, 0.0035,0.004, 0.005, 0.006, 0.007, 0.008,0.009, 0.010, 0.011, 0.012, 0.013,0.014, 0.015, 0.016, 0.018, 0.020,0.022, 0.024, 0.025, 0.026, 0.028,0.030, 0.032, 0.034, 0.035& 0.040".

CODE TYPE PRICE19613 Dual Reading Combi Feeler Gauge 32 Blades.... £19.99

CALIPER GAUGES

MINIATURE BRASS CALIPERS pocket size vernier type caliperswith graduations in metric and imperial. 3 sizes are available, idealfor working inconfined spaces.

CODE TYPE PRICEGAGP02 Mini Brass Caliper Gauge 2"................................ £3.55GAGP03 Mini Brass Caliper Gauge 3"................................ £3.99GAGP04 Mini Brass Caliper Gauge 4"................................ £4.99

DRAPER PLASTIC CALIPER GAUGE for internal, external anddepth measurements. Metric and imperial graduations, reading150mm/6" with a vernier scale of 1/128" x 0.05mm.

CODE TYPE PRICEGAP010 Draper Plastic Caliper Gauge............................... £3.50

DRAPER CALIPER GAUGES general purpose steel calipergauges for internal, external and depth measurements with athumb wheel for fine adjustment. Metric and imperial graduationreading 110mm/4½" and 150mm/6". Both sizes have a vernierscale of 1/128" x 0.05mm. Made in Germany.

CODE TYPE PRICEGAGP05 Draper Caliper Gauge 5"...................................... £5.99GAGP06 Draper Caliper Gauge 6"...................................... £7.49

DRAPER EXPERT QUALITY VERNIER GAUGE with fine adjust-ment screw for internal, external, depth and step measurements.Manufactured from high quality stainless steel with permanentlyetched graduations reading 0-140mm/0-5-1/2" with a vernier scaleof 0.001" (1/1000") and 0.02mm (1/50mm). Matt chrome platedbeam and fine adjustment screw. Supplied in a storage case.

CODE TYPE PRICEGAFA40 Expert Quality Vernier Gauge with Fine Adj......... £28.99

STAINLESS STEEL DIAL CALIPER GAUGE easy to use calipergauge for internal, external, depth and step measurement. Idealfor small small components or in restricted spaces, measuringrange 0-100mm with a clear read-off to 0.02mm. Thumb wheel forfine adjustment, zero adjustment. Supplied in a robust case.

CODE TYPE PRICEGADG23 Mini S/S Dial Caliper Gauge Metric 0 - 100mm.... £24.99

IF THERE ARE OTHER PRODUCTSTHAT YOU WOULD LIKE US TO STOCK,PLEASE FEEL FREE TO LET US KNOW.


SQUIRES TEL. 01243 842424 - FAX. 01243 84252560

ELECTRONIC CALIPER GAUGES

MC DIGITAL CALIPER a high quality caliper manufactured fromglass reinforced nylon. Ideal for accurate and reliable measure-ments, ease of use and speed of operation in both metric andimperial. Measures internal, external, and step with instantmetric/imperial conversion and zero may be set in any position.The unit is powered by a single button cell. Capacity 0-4"/0-100mmResolution0.01"0.1mm

CODE TYPE PRICE040-800 MC Plastic Caliper 0-4"/100mm........................... £12.99

ELECTRONIC CALIPER GAUGES high quality stainless steel dig-ital caliper gauges for internal, external, depth and step measure-ments. The LCD display allows quick and easy readings, instantmm/in conversion and zero may be set in any position. Poweredby a single button cell. 3 sizes are available.Capacity0-4"/0-100mm 0-6"/0-150mm0-12"/0-300mmResolution0.0005"0.01mm

CODE TYPE PRICE040-029 Electronic Caliper Gauge 0 - 4"/100mm............... £19.99GAEC76 Electronic Caliper Gauge 0 - 6"/150mm............... £19.99040-034 Electronic Caliper Gauge 0 - 12"/300mm............. £44.99

PROFESSIONAL DIGITAL VERNIER CALLIPER professionaldigital calipers with four function measurement, internal, external,depth and step. It has thumb lock adjustment, zero-setting at anyposition and a 13mm x 38mm large display screen with metric andimperial measurement. Manufactured from hardened stainlesssteel. Supplied with SR44 battery and carry/storage case.Capacity0-6" 0-150mm

CODE TYPE PRICE041-244 S/L Professional Digital Caliper 0 - 6"/150mm..... £19.99

MOORE & WRIGHT DIGITAL CALIPER this high quality caliper ismanufactured from glass reinforced nylon which is highly durable.Ideal for accurate and reliable measurements, ease of use andspeed of operation in both metric and imperial. Measures internal,external, depth and step with instant metric/imperial conversionand zero may be set in any position. Powered by a button cell.Capacity0-6" 0-150mmResolution0.01"0.1mm

CODE TYPE PRICEGA015D M & Wright Digital Plastic Caliper 0-6"/150mm.... £51.99

SOLAR POWERED DIGITAL CALIPER a high quality dual pow-ered caliper manufactured from Carbon Fibre composite. Ideal foraccurate and reliable measurements, ease of use and speed ofoperation in both metric and imperial. Measures internal, external,depth and step with instant metric/imperial conversion and zeromay be set in any position. The unit is powered by a single coincell (CR2016). Capacity 0-6"/0-150mm, Resolution 0.01"/0.1mm

CODE TYPE PRICE040-945 Carbon Comp Solar Digital Caliper 0-6"/150mm.. £17.99

SOLAR POWERED DIGITAL CALIPER a high quality dual pow-ered caliper manufactured from stainless steel. Ideal for accurateand reliable measurements, ease of use and speed of operation inboth metric and imperial. Measures internal, external, depth andstep with instant metric/imperial conversion and zero may be set inany position. The unit is powered by a single coin cell (CR2016).Capacity 0-6"/0-150mm, Resolution 0.01"/0.1mm

CODE TYPE PRICE040-949 Stainless Steel Solar Digital Caliper 0-6"/150mm £39.99

MICROMETERS

METRIC MICROMETERS standard quality outside micrometers,with error adjustment screw. 2 types are available, metric reading0-25mm graduated to 1/50mm (0.01mm) and imperial reading 0-1" graduated 0.001".

CODE TYPE PRICEGA0060 Metric Micrometer 0-25mm................................... £5.99040-061 Imperial Micrometer 0-1"...................................... £5.99

HIGH QUALITY METRIC MICROMETER 0-25MM a high qualitymetric micrometer with an enamelled bow frame which is cut awayat the anvil end to facilitate measurements in narrow slots. It hastungsten carbide measuring surfaces, pearl chrome plate thimbleand sleeve with ratchet and locking lever. It is fitted with heatresistant pads. Measuring range 0-25mm graduated to 0.01mm.Supplied in a storage box with adjustment tool.

CODE TYPE PRICEGA0066 High Quality Metric Micrometer 0-25mm.............. £14.99



MOORE & WRIGHT EXTERNAL MICROMETERS 0-1" & 0-25mmthe 965 series micrometers have a dark blue enamelled recessedbow frame cut away at the anvil end to facilitate usage in narrowslots. Pearl chrome plate thimble and sleeve with ratchet and lock-ing lever. The 1965 and 1965M are similar to 965 and 965Mexcept that they have tungsten carbide tips. Each is supplied in aplastic storage case with adjustment wrench.

Code 965 965M 1965 1965M Cap. 0-1" 0-25mm 0-1" 0-25mm Grad. 0.001" 0.01mm 0.001" 0.01mmCODE TYPE PRICE965 M & Wright Micrometer 0-1"................................. £39.99965M M & Wright Micrometer 0-25mm.......................... £39.991965 M & Wright Micrometer 0-1"................................. £39.991965M M & Wright Micrometer 0-25mm.......................... £39.99

MEASURING SETS

6 PIECE MEASURING SET a useful selection of measuring toolswhich are commonly used in almost any project. The set con-tains:-6" spring dividers, 6" outside calipers, 6" inside calipers,depth gauge, pocket ruler and a vernier caliper gauge.

CODE TYPE PRICE59110 6 Piece Measuring Set......................................... £22.99

BORE GAUGES

L/C BORE GAUGES a range of economically priced bore gaugesmanufactured from stainless steel with permanently etched metricgraduations. The taper is accurate throughout the length of thegauge making it a convenient tool for measuring diameters ofsmall holes and slots etc.

CODE TYPE PRICE040-822 L/C Bore Gauge 1 - 15mm................................... £3.99040-202 L/C Bore Gauge 15 - 30mm................................. £6.99040-712 L/C Bore Gauge 30 - 45mm................................. £7.99

BORE GAUGE METRIC manufactured from stainless steel withpermanently etched metric graduations. The taper is accuratethroughout the length of the gauge making it a convenient tool formeasuring diameters of small holes and slots etc. Range 1 -15mm.

CODE TYPE PRICE040-201 Groz Bore Gauge Metric 1 - 15mm...................... £6.99

TELESCOPIC GAUGE SET

TELESCOPIC GAUGE SET used for the accurate measuring ofbore diameters and groove widths. The spring-loaded plungerexpands within the groove and is then locked in position. The boregauge is then removed and the size can then be measured with amicrometer or caliper gauge. Satin chrome finish and supplied in aPVC wallet. The set of 6 gauges cover the size range from 8mm(5/16") to150mm (6").

CODE TYPE PRICE52416 Telescopic Gauge Set.......................................... £29.99

UNIVERSAL BEVEL PROTRACTOR

UNIVERSAL BEVEL PROTRACTOR SET used for the accuratemeasuring of angles, setting up jigs, laying out, and can be usedfor assembling and machining. It is fully calibrated through 360°and has a magnifying glass for clear reading. It is supplied with a300mm plain rule and acute angle attachment. Supplied in a plas-tic case for safe storage.

CODE TYPE PRICE52430 Universal Bevel Protractor Set............................. £64.99

MAGNETIC BASES & DIAL GAUGES

MINIATURE MAGNETIC BASE miniature magnetic base with fineadjustment for use with dial test indicators.The powerful magnet in the base which isalways engaged. The base has a precisionground surface and a keeper plate is suppliedwhich should be replaced after use.

Overall height - 138mm. Shaft height - 100mm.Base diameter - 28mm.

CODE TYPE PRICEGA0125 Mini Magnetic Base with Fine Adjustment............ £9.99

OUR SHOP IS AT100 LONDON ROAD

BOGNOR REGISMONDAY - FRIDAY 9.00 - 5.30

SATURDAY 9.00 - 5.30

FREE PARKING FOR 2 HOURS


SQUIRES TEL. 01243 842424 - FAX. 01243 84252562

STANDARD MAGNETIC BASE a high quality magnetic base foruse with dial test indicators withfine adjustment. Features a strongmagnet which is operated by anOn/Off switch. Precision groundsurface.Base dimensions50 x 55 x 60mm.Main shaft180 x 12mm. Height overall 240mm.**Product subjectto minor designchange**.

CODE TYPE PRICEGA0132 Magnetic Base with Fine Adjustment................... £24.99

METRIC DIAL INDICATOR 41mm an expert quality metric dialindicator reading 0 -100 in metricgraduations of 0.01mmwith a range of 5mm. The bezel diameteris 41mm.

CODE TYPE PRICE51855 Metric Dial Indicator 0.01mm/5mm....................... £39.99----- DIAL INDICATORS 55mm expert quality dial indicators reading 0- 100 in metric or imperial graduations. The bezel diameter is55mm. The metricversion is graduated0.01mm, range 10mm.The imperial versionis 0.0005", range 1".

CODE TYPE PRICE51830 Dial Indicator 0.01mm/10mm................................ £24.9951831 Dial Indicator 0.0005"/1"....................................... £29.99

DUAL READING DIAL INDICATOR GAUGE an Expert Qualitydual reading dial gauge, reading 0 - 100 in metric and imperialgraduations. Graduations0 - 25mm x 0.01mm &0 - 1" x 0.001". The bezeldiameter is 55mm with an8mm stem. It is fitted witha lug on the backof the case.

CODE TYPE PRICE65781 Dial Indicator Gauge Metric & Imperial................. £49.99

METRIC DIAL INDICATOR an expert quality metric dial indicatorreading 0 - 40 - 0 in graduations of 0.01mm. The bezel diameter is31mm. It is fitted with two mounting lugs.

CODE TYPE PRICE040-022 Metric Dial Indicator.............................................. £32.99

DRAPER DIAL TEST INDICATOR KIT METRIC an ideal all-roundexpert quality dial test indicator kit for engineers and apprentices.The dial test indicators have an accuracy of 0.01mm. Contains:-metric dial test indicator (0-25mm) with plunger, metric dial testindicator (0-1.5mm) with stylus, magnetic stand with fine adjust-ment, 22 interchangeable tips for dial test indicator with plungerand 6mm and 8mm stylus for dial test indicator clamp.

CODE TYPE PRICE46609 Draper Dial Test Indicator Kit Metric..................... £99.99

WIGGLER AND CENTRE FINDER SET

WIGGLER SET for the accurate location of working points on drillpresses, milling and jig boring machines etc. Contents:- chuckholder, needle point, ball contact, disc contact attachments and off-set indicator holder. All supplied in a plastic storage wallet. 2 stetsare available, a good qaulity budget set and a premium set manu-factured by LS Starrett Company.

CODE TYPE PRICE040-707 L/C Wiggler and Centre Finder Set...................... £8.99040-828 Starrett Wiggler and Centre Finder Set................ £39.99

WATERLINE MARKER

WATERLINE MARKER ideal for the accurate marking of water-lines on model ships, also usefulfor marking lines on many othermodels including model carsand aeroplanes etc. Suppliedcomplete with pencil which canbe set at any position on thepillar. Pillar height 200mm,height overall 250mm.

CODE TYPE PRICEEA7378 Waterline Marker.................................................. £15.99

POST FREE DELIVERY ON ALL ORDERSWITHIN THE UNITED KINGDOMMINIMUM ORDER VALUE £15.00



SURFACE GAUGES

UNIVERSAL SURFACE GAUGE manufactured from tool steelhardened and tempered and suppliedwith two pillars - 230mm and 300mm.The double-ended scriber can bemounted in any position and setat any angle on the pillar, final fineadjustment is obtained by theadjusting screw on the base. Thebase has a 'V' groove for use oncylindrical work and two retractablegauge pins are provided. Basewidth 80mm x 65mm.

CODE TYPE PRICEGASG39 Universal Surface Gauge..................................... £21.99M/W101B Moore & Wright Universal Surface gauge............ £84.99

SURFACE PLATE

GRANITE SURFACE PLATE a handy flat surface for measuring.Made entirely of granite it will always rename flat and changes intemperature and humidity will not effect its accuracy. Dims 305 x230 x 50mm. Flatness ±0.002mm

CODE TYPE PRICE040-191 Granite Surface plate 305 x 230 x 50mm............. £39.99

WORKSHOP ANGLE PLATES high quality angle plates used forlayout and inspection work.Manufactured from high qualityclose grain cast iron precisionground flat and square. 3 sizesare available.

CODE TYPE PRICEPG2 Workshop Angle Plate 2" x 2" x 2"....................... £9.99PG3 Workshop Angle Plate 3" x 3" x 3"....................... £13.99PG4 Workshop Angle Plate 4" x 4" x 4"....................... £19.99

ENGINEERS MINI LEVELS

MOORE & WRIGHT MINI LEVEL a small general purpose pocketlevel manufactured to exacting standards. It is manufactured froma single block of carbon steel and has a single vial. Ultra compactdimensions:- Length 50mm, width 18mm, height 18mm. Accuracy±1°

CODE TYPE PRICEELT001X Moore & Wright Mini Level with Single Vial.......... £12.39

MOORE & WRIGHT MINI LEVEL WITH VERTICAL PLUMB VIALa small general purpose pocket level manufactured to exactingstandards. It is manufactured from a single block of carbon steeland features a horizontal and vertical plumb vial. Compact dimen-sions:- Length 65mm, width 20mm, height 38mm. Accuracy ±1°.

CODE TYPE PRICEELT002X Moore & Wright Mini Level with 2 Vials................ £24.99

CALIPERS & DIVIDERS

SPRING CALIPERS AND DIVIDERS used for comparative mea-surements and marking out. Each has finely ground points and ahand wheelfor fineadjustment.3", 5"and 6"sizes.

Outside Inside Springcaliper caliper divider

CODE TYPE PRICECA0023 Outside Caliper 3"................................................ £3.79040-166 Outside Caliper 5"................................................ £4.99CA0026 Outside Caliper 6"................................................ £6.99CA0013 Inside Caliper 3"................................................... £3.79040-165 Inside Caliper 5"................................................... £4.99CA0016 Inside Caliper 6"................................................... £6.99CA0033 Spring Divider 3"................................................... £3.79040-167 Spring Divider 5"................................................... £4.99CA0036 Spring Divider 6"................................................... £6.99

MOORE & WRIGHT SPRING CALIPERS AND DIVIDERS usedfor comparative measurements and marking out. Manufacturedfrom high quality tool steel to exacting standards. Each has finelyground points and a hand wheel for fine adjustment. 3", 4" and 6"sizes.

Outside Inside Springcaliper caliper divider

CODE TYPE PRICEMW-523 Moore & Wright Outside Caliper 3"...................... £13.99MW-524 Moore & Wright Outside Caliper 4"...................... £14.50MW-526 Moore & Wright Outside Caliper 6"...................... £14.99MW-513 Moore & Wright Inside Caliper 3"......................... £13.99MW-514 Moore & Wright Inside Caliper 4"......................... £14.50MW-516 Moore & Wright Inside Caliper 6"......................... £14.99MW-503 Moore & Wright Spring Divider 3"......................... £13.99MW-504 Moore & Wright Spring Divider 4"......................... £14.50MW-506 Moore & Wright Spring Divider 6"......................... £14.99

ODDLEG CALIPERS

JENNY CALIPER oddleg calipers manufactured from polished toolsteel. The marking point which is mounted on the offset leg isground to a fine point and the straight leg has a locating spur.

CODE TYPE PRICE040-960 L/CJenny Calipers 6"............................................ £6.89MW3415 Moore & Wright Jenny Calipers 5"....................... £10.99

FLAT SQUARES

X-ACTO 3" TRIANGLE SQUARE a stainless steel triangle withpermanently etched imperial graduations. The triangle square isflat, to lay on the work piece.

CODE TYPE PRICEX7725 X-Acto 3" Triangle Square.................................... £6.99

X-ACTO 3" X 4" FLAT SQUARE a stainless steel flat square withaccurate permanently etched imperial graduations. The square isflat to lay on the work piece.

CODE TYPE PRICEX7726 X-Acto 3" x 4" Flat Square.................................... £6.99

STAINLESS STEEL FLAT ENGINEERS SQUARES a range offlat one piece sold steel squares which will lay flat on the work-piece. Manufactured from Inox steel to DIN875/0 for squarenessand parallelism. Use forprecision measuring inthe workshop. Suppliedin a hinged wooden box.

CODE TYPE PRICE040-210 Precision Flat Squre 75 x 50mm.......................... £12.99040-211 Precision Flat Squre 100 x 75mm........................ £13.99

ENGINEERS SQUARES

MINIATURE ENGINEERS SQUARE with solid steel stock withhardened, tempered and finely polished blade. Manufactured con-forming to BS939 workshop gradeB for squareness.Tolerance of the workingsurface and the bladeedge falls within0.016mm/0.00064".

CODE TYPE PRICE041-101 Miniature Engineers Square 1"............................. £6.50

FISHER ENGINEERS SQUARES solid steel stock with hardened,tempered and finely polished blades. Manufactured conforming toBS939 workshop gradeB for squareness.Tolerance of the workingsurface and the bladeedge falls within0.016mm/0.00064".

CODE TYPE PRICE041-002 Fisher Engineers Square to BS939B 2"............... £8.50041-003 Fisher Engineers Square to BS939B 3"............... £8.99041-004 Fisher Engineers Square to BS939B 4"............... £9.50041-006 Fisher Engineers Square to BS939B 6"............... £11.50041-009 Fisher Engineers Square to BS939B 9"............... £29.99041-012 Fisher Engineers Square to BS939B 12"............. £39.99

4 PIECE ENGINEERS SQUARE SET a set containing 4 carefullycrafted engineers squares manufactured from high quality toolsteel. The stock and blade are precision ground to ensurestraightness and accuracy, and the spring steel blade is hardenedand tempered for increased durability. Manufactured to BS939workshop Grade B. Supplied in a wooden storage case containing2" , 3", 4" & 6".

CODE TYPE PRICE040-246 4 Piece Engineers Square Set to BS939B........... £39.99

ENGINEERS KNIFE EDGE SQUARES a range of high qualityknife edge squares with solid steel stocks hardened, tempered andfinely polished. These squares will lay flat on the work piece andfacilitate precise visual control. The 50mm square is manufacturedto DIN875/00 form C, the 100mm and 150mm sizes are manufac-tured to BS939Workshop Grade Bfor squareness.Dimensions:-040-050:- 50 x 40mm

CODE TYPE PRICE040-050 Engineers Knife Edge Square 50mm................... £29.99


SQUIRES TEL. 01243 842424 - FAX. 01243 84252564

POST FREE DELIVERY ON ALL ORDERSWITHIN THE UNITED KINGDOMMINIMUM ORDER VALUE £15.00

ENGINEERS STOP SQUARES a range of precision stop squaressimilar to a flat engineers square butwith a extra piece added to the shorterblade. This piece would be lined up tothe edge of the workpiece whichensures accurate marking with theblade on the work. The stop alsoallows the square to stand freely,this is ideal for use with a surfaceplate for example. Manufacturedfrom special steel to DIN875/11for squareness and parallelism.

CODE TYPE PRICE040-300 Engineers Stop Square 75 x 50mm...................... £12.99040-310 Engineers Stop Square 100 x 70mm.................... £14.99040-320 Engineers Stop Square 150 x 100mm.................. £19.99

ADJUSTABLE ENGINEERS SQUARE a high quality precisionadjustable square which is equally suited for engineering and cabi-net making. The stock is supplied with 2 blades, one has squareends, the other blade has a 45° and a 60° end, a small steel rulewith metric graduations is supplied which can also be held in thestock. The stock can be fixed at any point along the blades andlocked in position. The blade lengths are4" and 2½" for thestock. All edges andfaces are ground forsquareness.

CODE TYPE PRICE040-010 Adjustable Engineers Square............................... £29.99

ENGINEERS MARKING GAUGE

ENGINEERS MARKING GAUGE a high quality precision markinggauge which is equally suited for engineering and cabinet making.It has permanent metric graduations which are easily read againstthe pearl chrome background. The setting can be locked using alarge knurled nut. Ideal for for transferring dimensions, rebatedepths etc. Graduations 0 - 200mm. All edges and faces areground for squareness.

CODE TYPE PRICE040-020 Engineers Marking Gauge 0 - 200mm.................. £14.99

CENTRE SQUARES

ENGINEERS CENTRE SQUARES used for fast and accuratelocation of centres in any round stock, particularly useful formachinists, toolmakers and lathe work. Manufactured from qualitytool steel, hardened and tempered. 2 sizes are available for maxi-mum dia of 38mm/1½" and maximum dia of 76mm/3". Lengthoverall 80mm and140mm respectively.

CODE TYPE PRICE040-003 Engineers Centre Square 38mm/1½"................... £6.99040-004 Engineers Centre Square 76mm/3"...................... £12.99

SCRIBES

MACHINISTS SCRIBER with a single hardened ground point andknurled body. Length 114mm/4½".

CODE TYPE PRICE040-086 Machinists Scribe 114mm/4½"............................. £1.99

ECLIPSE MACHINISTS SCRIBER a single ended scriber withknurled body and finely ground point. Length 5".

CODE TYPE PRICEECL227 Eclipse Machinists Scriber 5"............................... £3.99

ENGINEERS SCRIBER a double ended scriber with hardened andground points. Length 7".

CODE TYPE PRICESCR010 Engineers Scribe.................................................. £2.50ECL222 Eclipse Engineers Scriber.................................... £4.99

HANDY SCRIBER double ended scriber with a point and a knifeend for use as a scraper. Hardened and ground. Length 7".

CODE TYPE PRICESCR020 Handy Scribe........................................................ £2.5076229R Eclipse Handy Scriber.......................................... £7.99

ENGINEERS MINI POCKET SCRIBER a useful sized pocketscriber with a hardened steel reversible point and pocket clip.Length 3½"/ 89mm.

CODE TYPE PRICE040-151 Engineers Mini Pocket Scribe............................... £3.79

ENGINEERS POCKET SCRIBER a good quality pocket scriberwith knurled grip and pocket clip. The tip is reversible for safe stor-age in the pocket when not in use. Length 125mm.

CODE TYPE PRICE34104 Engineers Pocket Scriber..................................... £4.99

TCT SCRIBER AND GLASS CUTTER a high quality scriber witha tungsten carbide tip. It has a tip guard and pocket clip. Length145mm.

CODE TYPE PRICE040-657 TCT Scriber and Glass Cutter.............................. £2.99

CARBIDE TIP SCRIBER with a single carbide point for markinghardened material including steel and ceramics. The body isleightweight aluminium, knurled for good grip and is fitted with apocket clip. Length 4½".

CODE TYPE PRICE040-470 Carbide Tip Scribe 4½"........................................ £3.99



CARBIDE TIP SCRIBER with a single carbide point for markinghardened material including steel and ceramics. Heavy knurledbody with pocket clip. Length 5½".

CODE TYPE PRICE040-055 Carbide Tip Scribe 5½"........................................ £5.99

POCKET SCRIBE WITH TUNGSTEN POINT a clutch pencilscriber with a tungsten carbide point. Ideal for all scribing and willscribe hardened materials including steel and ceramics. The bodyis chrome finish, with a pocket clip. When not in use the point canbe retracted into the body.

CODE TYPE PRICE040-075 Pocket Scribe with Tungsten Point....................... £5.99

SLIM TUNGSTEN TIP SCRIBER a clutch pencil scriber with a0.5mm tungsten carbide point. It is ideal for all delicate scribingand will scribe hardened materials including steel and ceramics.The body is silver anodised and has a pocket clip. When not inuse the point can be retracted into the body. Spare points areavailable. Length 5½".

CODE TYPE PRICESCR930 Slim Tungsten Tip Scriber.................................... £9.99SCR931 Spare Tip for Slim Scriber (0.5mm x 30mm)........ £1.50

CHINA MARKERS suitable for smooth writing on china, glass,plastics, rubber and smooth non porous and porous sufaces.

CODE TYPE PRICE040-652 China Markers Pack of 2...................................... £1.00

AUTOMATIC CENTRE PUNCH/SCRIBES

SLIMLINE POCKET SCRIBE/AUTO CENTRE PUNCH a goodquality a pencil type scriber for delicate scribing and doubles as anautomatic centre punch. When scribing, if a reference mark isrequired, simply depress the scribe and an internal hammer mech-anism strikes the point and a perfect mark is made. The punch isadjustable to allow for working hard or soft materials. The scribehas a pocket clip. Length 150mm.

CODE TYPE PRICE040-023 Slim Pocket Scribe/Auto Centre Punch................ £6.99

SLIM SCRIBER/AUTO CENTRE PUNCH a pencil type scriber fordelicate scribing. A feature of this tool is that it also doubles as anautomatic centre punch. When scribing, if a reference mark isrequired, simply depress the scribe and an internal hammer mech-anism strikes the point and a perfect mark is made. The punch isadjustable to allow for working hard or soft materials. The scribehas a pocket clip and spare points are available. Length 5½".

CODE TYPE PRICESCR206 Slim Scriber/Auto Centre Punch........................... £14.99SCR207 Spare Tip for Slim Scriber/Auto Centre Punch..... £4.89

CENTRE PUNCHES

PRIORY CENTRE PUNCHES a high quality range of hardenedsteel punches carefully heat treated for long life. Precisely knurledbody with square head which gives good striking area and pre-vents the punch from rolling. Manufactured in England.

CODE TYPE PRICECP-116 Priory Centre Punch 1/16".................................... £3.79CP-332 Priory Centre Punch 3/32".................................... £3.79CP-18 Priory Centre Punch 1/8"...................................... £3.79CP-532 Priory Centre Punch 5/32".................................... £3.79CP-316 Priory Centre Punch 3/16".................................... £3.79CP-14 Priory Centre Punch 1/4"...................................... £3.79ECL351A Eclipse Centre Punch 1/8".................................... £3.99ECL351B Eclipse Centre Punch 5/32".................................. £3.99ECL351C Eclipse Centre Punch 3/16".................................. £3.99ECL351D Eclipse Centre Punch 1/4".................................... £3.99

DRAPER OCTAGONAL CENTRE PUNCH an expert qualityoctagonal centre punch, manufactured from specially air hardenedchrome vanadium steel for long life. The tips are accuratelyground with specially tempered heads.

CODE TYPE PRICE51752 Draper Octagonal Centre Punch 120 x 4mm....... £3.4951760 Draper Octagonal Centre Punch 120 x 5mm....... £3.4951778 Draper Octagonal Centre Punch 150 x 5mm....... £5.49

AUTOMATIC CENTRE PUNCH a hand operated centre punchwhich does not require a hammer. The tool is held in an uprightposition and then depressed for a perfect centre mark every time.Adjustable for hard/soft materials, light/heavy indents. Heavyknurled body for easy handling. Length 130mm.

CODE TYPE PRICE040-289 Automatic Centre Punch....................................... £4.99

AUTOMATIC CENTRE PUNCH an expert quality heavy duty auto-matic centre punch with special S2 steel tip for marking hard mate-rials. Adjustable striking force, with knurled body for easy han-dling.

CODE TYPE PRICE13612 Automatic Centre Punch....................................... £10.99

H/D AUTOMATIC CENTRE PUNCH an automatic centre punchwhich is is deal for making light indents to heavy punching withoutusing a hammer. The pressure can be varied by rotating the head.

CODE TYPE PRICE040-101 H/D Automatic Centre Punch 150mm.................. £7.99

PRIORY 271 AUTOMATIC CENTRE PUNCH a high quality auto-matic centre punch which is is deal for making light indents toheavy punching without using a hammer. The depth of impressioncan be adjusted via the screw cap for light indents to heavy punch-ing.

CODE TYPE PRICE040-271 Priory 271 Automatic Centre Punch 160mm........ £15.99


TEL. 01243 842424 - FAX. 01243 84252566

OPTICAL CENTRE PUNCH

OPTICAL CENTRE PUNCH a precision tool which provides a sim-ple yet accurate method of precise centre punching on finelyscribed work. It consists of a steel holder, 2 clear acrylic rods and2 hardened steel punches with a 60° and 90° point. The acrylicrods have an engraved cross on one and a bullseye on the other.The rods are used to sight the positioning, acting to carry light andto magnify at the same time. Once aligned the base which has anon-slip surface on the underside, is held firmly and the acrylic rodis exchanged for the chosen punchwhich is the lightly struck leaving anindentation in the precise position.The position can be re-checked ifrequired by replacing the acrylic rod.Base diameter 48mm, diameter ofpunches 9.5mm. Supplied in awooden box.

CODE TYPE PRICE040-244 Optical Centre Punch........................................... £28.99

ENGINEERS BLUE

MICROMETER ENGINEERS MARKING BLUE gives a clear markon any metal in any light,and being a lubricant itcannot damage bearingsor other working parts.Supplied in a 38g tin.

CODE TYPE PRICEEGBLUE Engineers Blue..................................................... £4.89

TRANSFER PUNCHES

TRANSFER PUNCHES a pair of unique punches used for trans-ferring the positions of holes from one piece of work to another.One punch has 5 locating diameters varying from 6 - 19mm, theother has a conical end for transferring the positions of counter-sunk holes. The master is placed on top of the new piece of mate-rial, a light tap with a hammer is required to drive the spring loadedpunch into the new workpiece below. The working length of thepunch is 30mm, overalllength is 110mm. Supplied as a pair.

CODE TYPE PRICE040-026 Transfer Punches Pair.......................................... £14.99

S/L 28 PIECE TRANSFER PUNCH SET 2 - 13mm a 28 piecetransfer punch set. Punches range from 2-13mm (3/32"-1/2").They accurately transfer holesdrilled in one workpiece toanother. With pointed tips forprecision marking.

CODE TYPE PRICE040-575 S/L 28 Piece Transfer Punch Set 2 - 13mm......... £16.99

TRANSFER PUNCH SET a full set of transfer punches rangingfrom 3/32" to 1/2" diameter. They are used to transfer the positionof holes drilled in one workpiece to another quickly and accurately.The master workpiece is placed on top of the next workpiece, thepunch is placed in the hole and the small point on the end thepunch marks the position of the next hole to be drilled. The punch-es are hardenedand ground. Suppliedas a set of 28 punchesin a storage stand.Length of punches 4-7/8".

CODE TYPE PRICE040-031 28 Piece Transfer Punch Set................................ £24.99

DRIVE PIN PUNCHES

MINIATURE PIN PUNCH SET a high quality miniature pin punchsupplied with 2 spare tips. Used for various applications includingdriving miniature pins, and producing rivet marks in thin sheet.Available with either 0.8mm or 1.0mm tips. Note the tips are not interchangeable.

CODE TYPE PRICE041-000 Miniature Pin Punch 0.8mm................................. £5.99041-001 Miniature Pin Punch 1.0mm................................. £5.99

4" DRIVE PIN PUNCH SET hardened parallel pin punches idealfor driving shafts and removing cotter pins etc. Knurled body withcentreless ground tip.The 1/16" punch isavailable individually.

DPPS10 sizes:-1/16" 3/32"1/8" 5/32"

CODE TYPE PRICEDPP116 Drive Pin Punch 1/16".......................................... £2.50DPPS10 Drive Pin Punch Set 1/16"-5/32"........................... £6.99

PARALLEL PIN PUNCH 3/32" a parallel pin punch with a heavyknurled body and 3/32" pin punch. The length overall is 150mmwith a 43mm parallel drive.

CODE TYPE PRICEDPP007 Parallel Pin Punch 3/32" - Length 150mm............ £2.99

PARALLEL PIN PUNCHES long pattern 200mm overall lengthwith 90mm parallel drive. 5 sizes available individually and a setcontaining one of each size in a wallet.

CODE TYPE PRICE19675 Parallel Pin Punch 1/8"......................................... £2.9919676 Parallel Pin Punch 3/16"....................................... £3.2519677 Parallel Pin Punch 1/4"......................................... £3.2519678 Parallel Pin Punch 5/16"....................................... £3.7919679 Parallel Pin Punch 3/8"......................................... £3.7919674 5 Piece Parallel Pin Punch Set............................. £15.99



DRAPER OCTAGONAL PARALLEL PIN PUNCH an expert quali-ty octagonal parallel pin punch. Made of air hardened chromevanadium steel for long life with accurately ground tips and spe-cially tempered heads.

CODE TYPE PRICE51645 Draper Octagonal Parallel Pin Punch 2.0mm....... £5.8051653 Draper Octagonal Parallel Pin Punch 2.5mm....... £5.8051661 Draper Octagonal Parallel Pin Punch 3.0mm....... £5.8051679 Draper Octagonal Parallel Pin Punch 3.5mm....... £5.8051687 Draper Octagonal Parallel Pin Punch 4.0mm....... £5.8051695 Draper Octagonal Parallel Pin Punch 5.0mm....... £5.8051702 Draper Octagonal Parallel Pin Punch 6.0mm....... £5.8051710 Draper Octagonal Parallel Pin Punch 8.0mm....... £6.7013041 5 P/c Oct P/Pin Punch Set 3.0, 3.5, 4, 5 & 6mm.. £27.99

DRAPER OCTAGONAL PARALLEL PIN PUNCH 6 P/c SET anexpert quality octagonal parallel pin punch set. Made of air hard-ened chrome vanadium steel for long life with accurately groundtips and specially tempered heads. Supplied in a steel magazinecase. Tip diametersof 2, 3, 4, 5, 6and 8mm.

CODE TYPE PRICE74712 Draper Octagonal Parallel Pin Punch 6 P/c Set... £53.80

SLIDING PUNCH SET a set of sliding punches used by clockmakers and engineers for chasing pins or dowels on fine equip-ment. When chasing a small pin or dowel with a conventional pinpunch the punch spindle may sometimes buckle in use if the pin isstuck. The body of the punch is slid down to the end of the punchso that the whole punch is placed over the job. The punch is thengently tapped with a hammer to move the pin, the body of thepunch is supports the spindle of the punch. The punches aremade from chrome vanadium steel, the sliding punch body is nick-el plated. The sizes included in the set are:- 0.9, 1.4, 1.8, 2.4, 2.8,3.4, 3.9 and 5.9mm.Supplied in a wallet.

CODE TYPE PRICE040-028 8 Piece Sliding Punch Set.................................... £26.99

DRAPER LONG TAPER PIN PUNCH an expert quality engineer’spattern long taper pin punch, manufactured from specially air hard-ened chrome vanadium steel for long life.

CODE TYPE PRICE13415 Draper Long Taper Pin Punch 200 x 3.0mm........ £10.9913416 Draper Long Taper Pin Punch 225 x 5.0mm........ £12.9913417 Draper Long Taper Pin Punch 250 x 6.0mm........ £15.9913418 Draper Long Taper Pin Punch 300 x 8.0mm........ £19.99

LETTER & NUMBER STAMPS

NUMBER & LETTER STAMP SET a combined set of numbersand letters for marking metals and other solid materials. The setcontains the letters A to Zplus '&' and numbers 0-8(6 is used twice). Figureheight 1/16" (1.6mm).Manufactured from aquality steel and suppliedin a storage box.

CODE TYPE PRICE040-009 Number & Letter Stamp Set 1/16" (1.6mm).......... £10.99

NUMBER STAMP SET for marking metals and other solid materi-als. Manufactured from high quality steel, heat treated to givemaximum endurance and accuracy of impression. The set contains0-8 (6 is used twice), stampheight 1/8" (3mm). Made inEngland, supplied in a plasticstorage case. A range ofeconomically priced importedsets are also available withfigure heights of 1/8", 3/16"and 1/4".

CODE TYPE PRICECPN110 Priory Number Stamp Set 1/8"............................. £13.9937336 Number Stamp Set 1/8"........................................ £6.9937337 Number Stamp Set 3/16"...................................... £9.9937338 Number Stamp Set 1/4"........................................ £10.99

LETTER STAMP SET for marking metals and other solid materi-als. Manufactured from high quality steel, heat treated to give max-imum endurance and accuracy of impression. The set contains Ato Z and '&'. The stamp height is 1/8" (3mm). Made in England,supplied in a plasticstorage case. Arange of economicallypriced imported setsare also available withfigure heights of 1/8",3/16" and 1/4".

CODE TYPE PRICECPL100 Priory Letter Stamp Set 1/8"................................. £29.9937333 Letter Stamp Set 1/8"........................................... £17.9937334 Letter Stamp Set 3/16"......................................... £27.9937335 Letter Stamp Set 1/4"........................................... £28.99

AUTOMATIC NUMBER AND LETTER STAMP SET a 38 pieceletter and number stamp set for use on wood or metal surfaces.The set contains 9 number stamps (0 to 8) and 26 letter bits (A toZ), one period bit, one ampersand bit, a brass auto centre punch,all in a plastic storage case. Character size is 1/8".

CODE TYPE PRICE040-138 Automatic Letter & Number Stamp Set................ £14.99


SQUIRES TEL. 01243 842424 - FAX. 01243 84252568

TOOL MAKERS CLAMPS

TOOLMAKERS CLAMPS case hardened steel jaws with temperedclamping screws. The screwheads are knurled and havecross holes for tightening.Screw clips keep the jaws inplace. Used for clamping smallitems while drilling and tapping etc.

CODE TYPE PRICECL0040 Toolmakers Clamp 2"........................................... £4.99CL0042 Toolmakers Clamp 2-1/2"..................................... £4.99CL0045 Toolmakers Clamp 3"........................................... £5.99CL0050 Toolmakers Clamp 4"........................................... £6.99CL0055 Toolmakers Clamp 6"........................................... £12.99ECL410 Eclipse Toolmakers Clamp 2".............................. £20.99ECL411 Eclipse Toolmakers Clamp 3".............................. £21.99ECL412 Eclipse Toolmakers Clamp 4".............................. £29.99

V-BLOCK & CLAMP

MACHINIST V-BLOCK AND CLAMP SET a matched pair of V-blocks and screw clamps. Manufactured from a hardened toolsteel and supplied as amatched and numberedpair. The 'V' angles areprecision ground central,parallel and square tothe sides and ends. TheV capacity is 25mm.Supplied as a set of twoblocks and two clamps.

CODE TYPE PRICECL0060 Machinist V-Block................................................. £26.99

BENCH BLOCK a 75mm diameter bench block which is ideal forsupporting small items. Witha hardened and polished steelbase.

CODE TYPE PRICE040-603 Bench Block 75mm............................................... £15.99

SLATER’S TRACK GAUGE

SLATER’S TRACK GAUGE a precision gauge for use when con-structing 7mm track.Brass construction.

CODE TYPE PRICES71510 Slater’s Track Gauge............................................ £7.50

WIRE GAUGE

WIRE GAUGE METRIC/IMPERIAL manufactured from heavygauge stainless steel. Used formeasuring the gauges of steelwire, hot and cold rolled sheetsteel. The metric dimensionsare recorded on one side andgauge marking is on the other.

CODE TYPE PRICE040-036 Wire Gauge Metric/Imperial 0 - 36........................ £19.99

SPRING BALANCES

SPRING BALANCE a range of low cost spring balances for aquick and easy method of weighing. It has a traditional style facewith clear and easyto read metric andimperial graduations.

CODE TYPE PRICE040-079 S/L Spring Balance 12.5Kg/25lb........................... £3.50040-081 S/L Spring Balance 25Kg/50lb.............................. £4.29040-083 S/L Spring Balance 50Kg/112lb............................ £4.99

CK POCKET BALANCE a range of pocket spring balances withbrass scale and black lacquered body, the hook and ring is tinnedfor corrosion protection. Calibrated in 1lb/½Kg divisions.

CODE TYPE PRICE049-025 CK Pocket Balance 12.5Kg/25lb.......................... £6.85049-032 CK Pocket Balance 15Kg/32lb............................. £7.99049-044 CK Pocket Balance 20Kg/44lb............................. £8.30049-050 CK Pocket Balance 23Kg/50lb............................. £8.50049-066 CK Pocket Balance 30Kg/66lb............................. £8.85049-088 CK Pocket Balance 40Kg/88lb............................. £13.60049-211 CK Pocket Balance 50Kg/112lb........................... £14.75

HANGING SCALES a quick and easy method of weighing.Robust metal casing with a durablepainted finish. Clear and easy toread metric scale in 50g increments.Simple method of calibration forcomparison weighing.

CODE TYPE PRICE040-017 Hanging Scales 5Kg............................................. £3.99040-001 Hanging Scales 10Kg........................................... £4.19

HANGING SCALES an accurate and quick method of weighingand measuring. Large 65mm diameterdual dial displays both metric and imperial. Convenient integral 1mtape measure. Robust metal handleand hanging hook.

CODE TYPE PRICE040-420 Hanging Scales 22Kg........................................... £4.50



OUR SHOP IS AT100 LONDON ROAD

BOGNOR REGISMONDAY - SATURDAY 9.00 - 5.30

MEASURING WHEELS

MICRO MEASURING WHEEL the telescopic shaft extendsbetween 350 and 810mm. Durable patterned handle for extra grip.Clear and easy to read metric dial measuring 0 - 999m with anaccuracy of +/- 2%.

CODE TYPE PRICE040-436 Micro Measuring Wheel 0 - 999M......................... £14.99

MINI MEASURING WHEEL a compact, foldaway mini measuringwheel with distance range of0-9999m. The comfortabletelescopic handle extends460-900mm. Sturdy dualwheels give good stabilityand analogue display containsan instant zero button.Foldaway wheel for storageinto canvas carrying bag.

CODE TYPE PRICE040-077 Mini Measuring Wheel 0 - 9999M......................... £24.99

INCLINOMETER

INCLINOMETER ideal for roofing, scaffolding and general anglemeasurement. Clear and easyto read dial divided into 90°quadrants. It has a durable100mm diameter plastichousing with a convenientmagnetic base.

CODE TYPE PRICE040-471 Inclinometer.......................................................... £4.99

HELPING HANDS

HEAVY DUTY HELPING HANDS WITH GLASS MAGNIFIER avariation of the popular Helping Hands with an extra large glasslens. The 90mm glass lens gives clear undistorted magnificationof x2½. The magnifier is mounted to the cross bar using ball jointsallowing universal positioning of the lens. The crocodile clip"hands" are mounted on across bar which is mountedon a ball joint. The heightof the lens and the "hands"can be raised or loweredon the column. Ideal forsoldering, assembling,painting etc.**Special Offer**Was £5.99 Now £4.99*

CODE TYPE PRICE020-861 Heavy Duty Helping Hands + Glass Magnifier..... £4.99

HELPING HANDS WITH LEDs AND IRON STAND a useful aidfor soldering small items. A combination of a soldering iron standand a helping hands. The magnifier has 2 LEDs for illuminatingthe workpiece. The heavy base keeps it stable, the main lens is65mm dia with x3 magnification, the 17mm inset lens is x12 nagni-fication.

CODE TYPE PRICE020-077 Helping Hands with 2 LEDs and Iron Stand......... £8.99

MINI TABLE LAMP MAGNIFIER

MINI TABLE LAMP FLUORESCENT MAGNIFIER a free standingmini magnifying table lamp with a 12 watt circular daylight tube,giving even light distribution and virtually no heat being emitted.The lamp features a 4" diameter glass lens providing x1.75 magni-fication and a x4 magnification close-up lens. The magnifyinghead is mounted toallow positioning asrequired. The lamphas a cover and aclear diffuser whichgives protection to thetube. Spare tubesare available. Idealfor craft and hobbywork, needlework,embroidery andinspection etc.

CODE TYPE PRICE120-093 Mini Table Lamp Fluorescent Magnifier............... £29.99120-094 Spare Tube for 120-091/120-093 Magnifier......... £6.50


SQUIRES TEL. 01243 842424 - FAX. 01243 84252570

SQUIRES GIFT VOUCHERSSupplied with a quality card

redeemable at any of our exhibitionstands, by mail order or at our shop.

GV5 - Gift Voucher Value £5.00GV10 - Gift Voucher Value £10.00GV20 - Gift Voucher Value £20.00

measuring - marking · measuring - marking angle measurer 58 ... waterline marker 62 wiggler &...

Documents