operating instructions condenser tumble dryer...operating instructions condenser tumble dryer to...

Operating instructionsCondenser tumble dryer

To avoid the risk of accidents or damage to the appliance, it is essentialto read these instructions before it is installed and used for the first time.

en-AU, NZ M.-Nr. 10 002 130

Caring for the environment

2

Disposal of the packingmaterialThe packaging is designed to protectthe appliance from damage duringtransportation. The packaging materialsused are selected from materials whichare environmentally friendly for disposaland should be recycled.

Recycling the packaging reduces theuse of raw materials in themanufacturing process and alsoreduces the amount of waste in landfillsites. Ensure that any plasticwrappings, bags etc. are disposed ofsafely and kept out of the reach ofbabies and young children. Danger ofsuffocation.

Disposing of your oldapplianceElectrical and electronic appliancesoften contain materials which, ifhandled or disposed of incorrectly,could be potentially hazardous tohuman health and to the environment.They are, however, essential for thecorrect functioning of your appliance.Therefore, please do not dispose ofyour old appliance with your householdwaste.

Please dispose of it at your localcommunity waste collection / recyclingcentre.

Ensure that your old appliance presentsno danger to children while beingstored for disposal.

Energy saving tipsTo avoid unnecessarily long dryingtimes and high consumption of energy:

– Make sure that your laundry isthoroughly spun before drying.The higher the spin speed, thegreater the savings that can be madein energy and time during drying, e.g.approx. 30% energy can be saved ifspun at 1600 rpm instead of 1000rpm.

– Load according to the optimumamount of laundry recommended forthe programme being used.Underloading is uneconomical.Overloading gives a poorer quality ofdrying and may cause unnecessarycreasing.

– Make sure the room temperature isnot too high. If there are other heatproducing appliances in the room inwhich the tumble dryer is located,make sure the room is well-ventilatedand switch the other appliances off, ifpossible.

– After every cycle remove the flufffrom the fluff filters in the door and inthe door opening.

– Check the condenser unit once ayear and clean it if necessary.

Contents

3

Caring for the environment ................................................................................. 2

Warning and Safety instructions ......................................................................... 5

Operating the tumble dryer ................................................................................ 13Control panel ......................................................................................................... 13Before using for the first time................................................................................ 14

Laundry care ........................................................................................................ 15

How to dry correctly............................................................................................ 16Brief instructions ................................................................................................... 16

Changing the programme sequence ................................................................. 18

Programme chart ................................................................................................ 19

Cleaning and care ............................................................................................... 22Emptying the condensed water container ............................................................ 22Cleaning the fluff filters.......................................................................................... 23

Cleaning the fluff filters without water .............................................................. 23Cleaning the fluff filters with water ................................................................... 24Refitting the fluff filters ..................................................................................... 24

Tumble dryer.......................................................................................................... 25Cleaning the condenser unit ................................................................................. 26

Opening the service panel................................................................................ 26Checking the heat exchanger unit ................................................................... 27Cleaning the condenser unit ........................................................................... 27Refitting the condenser unit ............................................................................ 29

Problem solving guide ........................................................................................ 30Problem solving guide........................................................................................... 30Check and fault messages.................................................................................... 30Unsatisfactory drying results................................................................................. 32Other problems ..................................................................................................... 33Changing the lamp ................................................................................................ 35

After sales service ............................................................................................... 36Repairs .................................................................................................................. 36Optional accessories............................................................................................. 36Warranty ................................................................................................................ 36

Contents

4

Installation and connection ................................................................................ 37Front view .............................................................................................................. 37Rear view............................................................................................................... 38Installation site....................................................................................................... 38

Transporting the machine to its installation site ............................................... 38Building under a continuous worktop / in a kitchen run................................... 39Washer and dryer stack ................................................................................... 39Levelling the dryer ............................................................................................ 39Room ventilation .............................................................................................. 40Before moving the tumble dryer again (e.g. when moving house) ................... 40

Electrical connection ............................................................................................. 41Externally draining condensed water .................................................................... 42

Arranging the drain hose .................................................................................. 42External drainage via a sink or gully ................................................................. 43Installation conditions requiring a non-return valve ......................................... 44

Consumption data ............................................................................................... 46

Technical data...................................................................................................... 47

Programmable functions .................................................................................... 49Extending the range of the drying level for the "Cottons" programme ................. 49Extending the drying level for the "Minimum iron" programme ............................ 50Anti-crease ............................................................................................................ 51Switching the buzzer on/off................................................................................... 52Altering the standard drying level in the"Automatic plus" programme ................. 53Extending the cooling down time.......................................................................... 54Standby ................................................................................................................. 55Clean out airways indicator ................................................................................... 57Adjusting the dryer's electronics for very soft water............................................. 58

Warning and Safety instructions

5

It is essential to read these instructions.

This tumble dryer complies with current local and national safetyrequirements. Inappropriate use can, however, lead to personalinjury and damage to property.

To avoid the risk of accidents and damage to the tumble dryer,please read these instructions carefully before using it for the firsttime. They contain important information on its safety, installation,use and maintenance.

Keep these instructions in a safe place and ensure that new usersare familiar with the content. Pass them on to any future owner.

Correct application

This tumble dryer is designed for domestic use and for use insimilar environments by guests in hotel or motel rooms, bed &breakfasts and other typical living quarters. This does not includecommon/shared facilities or commercial facilities within hotels,motels or bed & breakfasts.

This tumble dryer is not suitable for outdoor use.

It must only be used to dry items which have been washed in awater solution and which are marked on the manufacturer's carelabel as being suitable for tumble drying. If using dry cleaning kits,do so at your own risk, and follow the instructions provided on thepackaging. Any other applications may be dangerous. Miele cannot be heldliable for damage resulting from incorrect or improper use oroperation.


6

This appliance is not intended for use by persons (includingchildren) with reduced physical, sensory or mental capabilities, orlack of experience or knowledge, unless they are supervised whilstusing it or have been shown how to use it by a person responsiblefor their safety.

Safety with children

Young children must not be allowed to use this appliance.

Older children may only use the appliance when its operation hasbeen clearly explained to them and they are able to use it safely,recognising the dangers of misuse.

Children must not be allowed to clean or maintain the tumbledryer unsupervised.

Please supervise children in the vicinity of the tumble dryer and donot let them play with it.

Technical safety

Before setting up the tumble dryer, check it for any externallyvisible damage.Do not install or use a damaged tumble dryer.

Before connecting the tumble dryer, ensure that the connectiondata on the data plate (fuse rating, voltage and frequency) matchesthe mains electricity supply. If in any doubt, consult a qualifiedelectrician.

Reliable and safe operation of this tumble dryer can only beassured if it has been connected to the mains electricity supply.

The electrical safety of this tumble dryer can only be guaranteedwhen correctly earthed. It is essential that this standard safetyrequirement is met. If in any doubt, please have the household wiringsystem tested by a qualified electrician. Miele cannot be held liablefor the consequences of an inadequate earthing system (e.g. electricshock).


7

Do not connect the tumble dryer to the mains electricity supply byan extension lead. Extension leads do not guarantee the requiredsafety of the appliance (e.g. danger of overheating).

If the connection cable is faulty, it must only be replaced by aMiele approved service technician to protect the user from danger.

Unauthorised repairs could result in unforeseen dangers for theuser, for which Miele cannot accept liability. Repairs should only beundertaken by a Miele authorised service technician, otherwise anysubsequent damage will not be covered by the warranty.

Faulty components must only be replaced by genuine Miele spareparts. Miele can only guarantee the safety of the appliance whenMiele replacement parts are used.

In the event of a fault or for cleaning purposes, the tumble dryer isonly completely isolated from the electricity supply when:

– it is switched off at the wall socket and the plug is withdrawn, or

– it is switched off at the mains circuit breaker.

This tumble dryer must not be installed and operated in mobileinstallations (e.g. on a ship).

Do not make any alterations to the tumble dryer, unless authorisedto do so by Miele.

Please observe the instructions in "Installation and connection"and "Technical data".

The accessibility of the plug must be always ensured in order toseparate the tumble dryer from the mains.

Do not block the gap between the bottom of the tumble dryer andthe floor with plinth facings, deep pile carpet etc. This would hinder asufficient flow of air to the tumble dryer.

Make sure the dryer door can be opened without hindrance afterinstallation.


8

This tumble dryer is supplied with a special lamp to cope withparticular conditions (e.g. temperature, moisture, chemicalresistance, abrasion resistance and vibration). This special lampmust only be used for the purpose for which it is intended. It is notsuitable for room lighting.

Correct use

Caution! Risk of fire.

To avoid the possible danger of fire, please read these warningscarefully.

A clogged filter is a fire hazard!The fluff filter must be cleaned after every programme.

The maximum load for this tumble dryer is 7.0 kg (dry weight). Seethe "Programme chart" for the maximum recommended loads forindividual programmes.

To prevent the risk of fire, do not connect the tumble dryer via acontrollable socket (e.g. a timer or a peak-load switch-off device).If the drying programme is interrupted before the end of the coolingdown phase, this could cause the laundry to self-ignite.


9

Oil-affected items can ignite spontaneously, especially whenexposed to heat sources such as in a tumble dryer. The items become warm, causing an oxidation reaction in the oil.Oxidation creates heat. If the heat cannot escape, the items can become hot enough tocatch fire. Piling, stacking or storing oil-affected items can preventheat from escaping and so create a fire hazard. If it is unavoidable that fabrics contaminated with vegetable orcooking oil, or hair care products, be placed in a tumble dryer, theyshould first be washed in hot water with extra detergent - this willreduce, but not eliminate, the hazard.

To prevent the risk of fire, the following textiles must not be driedin this tumble dryer:

– Items which have not been washed.

– Items, such as workwear, which have not been thoroughlycleaned and which are still soiled with grease, oil or otherdesposits (such as cosmetics, lotions etc). If items have not beenthoroughly cleaned, there is a danger that these might ignite whenheated, even after they have been removed from the dryer at theend of the programme.

– Items that have been soiled with substances such as cooking oil,acetone, petrol, kerosene, spot removers, turpentine, waxes, waxremovers and other chemicals (e.g. mops and floor cloths).

– Items which have been splashed with hair lacquer, hair spray, nailvarnish remover or similar substances.

When washing such heavily soiled items ensure that you usesufficient detergent and select a high temperature. If in doubt,wash the items several times.

Remove all items from pockets (e.g. lighters, matches).


10

Warning: Ensure that you always wait until the end of theprogramme before removing the laundry. If the drying programme isstopped prematurely, remove the laundry immediately and hang it upor spread it out to cool it down.

Fabric softener and similar products must be used according tothe instructions on the manufacturer's packaging.

To prevent the risk of fire, the following textiles must not be driedin this tumble dryer:

– Items which have been cleaned using chemicals (e.g. professionaldry-cleaning agents).

– Fabrics which contain a large proportion of rubber, foam rubber orrubber-like materials. For example, products made from latexfoam rubber, shower caps, waterproof textiles, rubberised articlesand items of clothing and pillows with foam rubber filling.

– Damaged fabrics which contain padding or fillings (e.g. pillows,jackets). When damaged, the filling can get out with the risk of itigniting in the dryer.

In many programmes, the heating phase is followed by a coolingdown phase to ensure that the items are not too hot to handle whenyou remove them (this also avoids the danger of the laundry self-igniting). The programme is not finished until the cooling down phasehas been completed.As soon as the programme has finished, remove all laundry from thedrum.

Do not let anyone sit or lean on the door, as this can cause thetumble dryer to tip up.

Always close the door after use. This way you will avoid thedanger of:

– children climbing onto or into the dryer or hiding things in it.

– pets or other small animals climbing into it.


11

The dryer must not be used without the fluff filters in place or ifthe fluff filters are damaged in any way.

The fluff filters must be cleaned regularly.

The dryer must not be used without the condenser unit in place.

The fluff filters must be thoroughly dried after wet cleaning. Do notreplace them if they are damp or wet. Damp or wet filters couldcause operational faults.

Do not install the tumble dryer in a room where there is a risk offrost occurring. At temperatures around freezing point the tumbledryer may not be able to operate properly. There is a risk of damageif the condensed water is allowed to freeze in the pump and hoses.

If the water is drained externally through the drain hose instead ofbeing collected in the condensed water container, make sure thedrain hose is securely attached if you hang it in a sink or basin toavoid the hose slipping and the water causing damage.

Condensed water is not drinking water.It can cause health problems in both people and animals.

Always keep the area around the tumble dryer free of dust andfluff.Dust drawn into the tumble dryer can cause blockages in the heatexchanger over time.

The tumble dryer must not be hosed down.

Accessories

Only use genuine Miele spare parts and accessories with thisappliance. If spare parts or accessories from other manufacturersare used, this will invalidate the warranty, and Miele cannot acceptliability.


12

A Miele tumble dryer can be stacked on top of a Miele washingmachine using the appropriate stacking kit (available as an optionalaccessory). Please make sure you order the correct one for the Mielewashing machine and Miele tumble dryer.

Miele cannot be held liable for damage caused by non-compliance with these Warning and Safety instructions.

Operating the tumble dryer

13

Control panel

a Display h minSee the following page for more information.

b Check / Fault indicator lightsSee "Problem solving guide".The PC check light is also used by service technicians to run diagnostic checkson your tumble dryer and may be used to update programming data in thefuture.

c Start button Press the Start button to start a programme.The Start indicator light will flash as soon as the programme can be started. Itlights up constantly once the programme has started.

d Programme selectorThe programme selector can be turned clockwise or anti-clockwise.

e On/Off button For switching the appliance on or off. or the programme duration will light up as confirmation that the tumble dryerhas been switched on.

f Door button Pressing this button will open the door even when the appliance is not switchedon at the mains.

Operating the tumble dryer

14

Display h min

The display shows:

– The programme duration (h:min =hours and minutes)

– Check and fault messages

– Programmable functions These are used to alter the dryer'selectronics to suit differentrequirements. See "Programmable functions" formore information.

Estimated time remaining

The estimated programme duration willappear in the h:min display in hours andminutes (estimated time remaining).Exception: Timed drying programmeswhich last for the duration stated in thecontrol panel. The following factors can all affect theestimated time remaining: residualmoisture content after spinning; type offabric; size of load; room temperature;fluctuations in power supply. Theelectronics continually assessconditions in the appliance and adjustthe estimated time remaining withincreasing accuracy. Because of this,the time displayed can alter during thecourse of a programme.

Drum lightingWhen the dryer is switched on at themains and the door is opened, the drumlighting will come on. It will go out a fewminutes later to save energy.

Before using for the first time

Before using the tumble dryer forthe first time, ensure that it iscorrectly installed and connected.

Laundry care

15

Garment care label symbols

Drying

Normal/Higher temperature

Low temperature

Do not tumble dry

Ironing

Very hot

Hot

Warm

Do not iron

Tips on drying

Overloading can cause unnecessarywear and tear to the laundry, give adisappointing drying result andcause more creasing.Always observe the maximumrecommended loads given in the"Programme chart". Never overloadthe drum.

– Open jackets so that they can dryevenly.

– Do not put soaking wet items into thetumble dryer to dry them; spin themthoroughly for at least 30 secondsafter washing.

– Use the Automatic plus programmefor drying mixed loads of cottons andminimum iron fabrics.

– Woollens and wool blends tend tobecome matted and shrink if dried ina tumble dryer. They can, however,be "fluffed up" in the Woollenshandcare programme.

– Down-filled garments have liningswhich have a tendency to shrink,depending on the quality of the items.They can be partially dried using theGentle smoothing programme.

– Pure linen should only be machinedried if specified as suitable by themanufacturer on the garment carelabel, as the surface of the fabric mayotherwise become rough.

– Loopknit garments (e.g. T-shirts andunderwear) tend to shrink dependingon their quality. Do not overdry thesetextiles. When purchasing thesegarments, it is advisable to take theirshrinkage properties into account.

– Minimum iron fabric tends to creasemore, the larger the load. This is alsothe case for garments made fromvery fine weave fabric, such as shirtsor blouses. If necessary, selectMinimum iron and reduce the size ofthe load.

– Starched laundry can be dried in thetumble dryer. To achieve the usualfinish, double the amount of starchshould be used.

– New dark coloured garments shouldbe washed and dried separately fromlight coloured garments to avoid thedanger of colours running anddiscolouring other garments or evenplastic components in the dryer. Darkcoloured fibres can also settle onlight coloured garments and viceversa.

How to dry correctly

16

Brief instructionsThe headings numbered (, , ...)show the operating sequence and canbe used as a brief guide to using yourdryer.

Preparing the laundry

Separate out the washed laundry andsort it according to:. . . the drying level required,. . . the type of fibre or weave,. . . size,. . . the moisture content after spinning.In this way an even drying result will beachieved.

Make sure that objects e.g.detergent dispensing balls have beenremoved from the laundry. Theycould melt, and cause damage to thedryer or the laundry.

– Check seams and stitching to ensurethat padding and linings are intact.

– Fasten duvet covers and pillow casesto prevent small items from beingrolled up inside them.

– Fasten hooks and eyes.

– Fasten any loose belts and ties.

– Sew in or remove underwiring frombras.

Switching on the tumble dryer

The tumble dryer may be switched onafter loading, saving energy as the lightwill not come on.

Press the button to switch thedryer on.

Loading the tumble dryer

Press the Door button to open thedoor.

Unfold the laundry and load looselyinto the drum.

Do not overload the drum. See the"Programme chart" forrecommended loads for eachprogramme. Overloading can causeunnecessary wear and tear to thelaundry and give a disappointingdrying result.

Before closing the door, make surethe fluff filter is correctly positioned inthe door.

Check the laundry is right inside thedrum so that it cannot get trapped ordamaged when the door is shut.

Shut the door either with a gentleswing, or lean against it and push itshut.

How to dry correctly

17

Selecting a programme

Turn the programme selector to therequired programme.

Starting the programme

Press the flashing Start button.

The indicator light for the Start buttonwill now light up constantly.

Please note: The programme durationshown in the display is an estimationand can vary.

Removing the laundry at the endof the programme

There is a cooling down phase at theend of the drying sequence. Theprogramme is not finished until lightsup and the buzzer sounds.

After the programme has finished, thedrum will continue to rotate in a specialrhythm, depending on the programmeselected, to prevent creasing, if you donot wish to remove it immediately (Anti-crease phase). There is no Anti-creasephase at the end of the Woollenshandcare programme. The duration ofthe Anti-crease phase is variable (see"Programmable functions").

Press the Door button.

Open the door.

Remove the laundry.

Check that all items have beenremoved from the drum. If items areleft in the dryer, they could bedamaged by overdrying when thedryer is next used.

Press the button to switch thedryer off.

Clean the fluff filters.

Close the door.

Empty the condensed watercontainer.

Useful tip: If condensed water isdrained away via the drain hose, thecondensed water container does nothave to be emptied.

Changing the programme sequence

18

Once a programme hasstarted ...

... changing the programme

You cannot change to anotherprogramme once a programme hasstarted (this prevents unintentionalalterations).

If you try to change a programme, lights up until the original programme isreset.

You will need to cancel the currentprogramme before you can select anew one.

... cancelling the programme

Turn the programme selector toFinish.

The items will be cooled down,depending on the temperature reachedand how long they have been dried for.

The programme is not finished until lights up.

Switch the dryer off and then onagain.

Select and start a new programmestraight away.

Adding or removing laundryafter a programme has started

Restart the programmeimmediately after adding orremoving items.Otherwise remove all items andspread them out to cool downcompletely.

Danger of burning!The drum and the items can get veryhot.Do not touch the back of the drumwhen adding or removing items.

Press the Door button.

Add or remove items.

Close the door.

Press the Start button.

Programme durationAltering the programme sequence cancause adjustments in the h min display.

Programme chart

19

Cottons Max. load 7.0 kg*

Normal+, Normal

Items Single and multi-layered cotton fabric such as towelling, jerseywear,T-shirts, underwear, workwear, covers, flannelette bed linen andbaby clothes.

Note The Cottons Normal+ programme is the most energy-efficient fordrying cotton items with normal residual moisture levels.

Normal - Low temperature

Useful for Delicate fabric (with the symbol on the care label, e.g. acrylicgarments) is dried at a lower temperature than in the Cottons Normalprogramme. The programme duration is longer.

Hand iron, Machine iron

Items Cotton or linen fabric requiring further processing, e.g.: table linen,bed linen, starched laundry.

Note To prevent laundry from drying out, it should be rolled up until youare ready for ironing.

* Weight of dry laundry

Programme chart

20

Minimum iron Max. load 3.5 kg*

Normal, Hand iron

Items Minimum iron items made of cotton, synthetic or mixed fibre, e.g.:tops, dresses, shirts, blouses, skirts, trousers and table linen.

Note With the Hand iron drying level, items are dried with very littlecreasing, depending on fabric type and amount of laundry.

Normal - Low temperature

Useful for Delicate fabric (with the symbol on the care label, e.g. acrylicgarments) is dried at a lower temperature than in the Cottons Normalprogramme. The programme duration is longer.

Automatic plus Max. load 5.0 kg

Items Mixed loads of garments suitable for the Cottons and Minimum ironprogrammes. Sort according to colour.

Timed drying Max. load 7.0 kg*

30 min warm air

Items – Multi-layered fabric whose layers have different dryingcharacteristics, e.g. jackets, pillows, sleeping bags and othervoluminous items.

– For drying individual items, e.g. bath towels, bathing costumes,tea towels and small loads.

15 min cool air

Items Any item which only needs airing.


Programme chart

21

Gentle smoothing Max. load 1.0 kg*

Items – Cotton and linen fabric.

– Minimum iron items made of cotton, synthetic or mixed fibre, e.g.trousers, jackets, shirts.

Notes – Smooths out creasing caused during the spin cycle in the washingmachine.

– Items are not dried completely in this programme.

– Remove items as soon as the programme has finished and leaveto finish drying at room temperature.

Woollens handcare Max. load 2.0 kg

Items Woollen garments and fabric containing wool blends, e.g. pullovers,jackets.

Notes – Wool and wool blend items are only fluffed up; they are not driedcompletely.

– Remove garments as soon as the programme has finished.


Cleaning and care

22

Emptying the condensed watercontainer

The condensed water is collected inthe condensed water container.

Empty the condensed watercontainer after every dryingprogramme.

The Empty the container indicator lightwill come on if the maximum level of thecondensed water container is reached.

The indicator light will go out when thedoor is opened and closed again whenthe tumble dryer is switched on.

Pull out the condensed watercontainer.

To prevent water running out, hold itat the front and towards the back andkeep it in a horizontal position whencarrying it.

Empty the container.

Replace the container in the dryer.

Condensed water can causehealth problems in people andanimals.Do not drink it.

Condensed water can be put tohousehold use (e.g. used in a steamiron or humidifier). To ensure that anyresidual particles of fluff in thecondensed water are removed beforeuse, pass it through a fine sieve orpaper filter first.

Cleaning and care

23

Cleaning the fluff filters

When to clean the fluff filters

Clean the surfaces of the fluff filtersin the door and the door openingafter each drying programme.Always check the fluff filters if theClean out airways indicator lightcomes on.

Cleaning the fluff filters without water

Useful tip: You can use a vacuumcleaner to remove the fluff.

Open the door and pull the fluff filter(1) out of the door as illustrated.

Remove any fluff from the hollow partof the door with a bottle brush or avacuum cleaner.

Also clean the door seal (2) with adamp cloth.

Use your fingers or a vacuum cleanerto remove the fluff from the surface ofthe filter.

Use your fingers or a vacuum cleanerto remove the fluff from the two flufffilters in the door opening.

Once clean, push the filter back intothe door holder until it clicks intoposition. Ensure it is facing thecorrect way.

Close the door.

Cleaning and care

24

Cleaning the fluff filters with water

If there is a great deal of compactedfluff on any of the filters, they shouldbe removed and cleaned with water.

Open the door and pull the fluff filterout of the door as describedpreviously.

The two filters in the door opening canalso be removed if you need to cleanthem with water.

Turn the dial on the left and rightfluff filter until you feel it click.

Pull the filter out of the door openingby the dial as shown .

Rinse all the filters under hot, runningwater.

Dry the fluff filters thoroughly withcare.

Clean the area underneath thesefilters, e.g. with a vacuum cleaner.

Refitting the fluff filters

Do not replace them if they aredamp or wet. Damp or wet filterscould cause operational faults.

Push the large filter back into thedoor holder until it clicks intoposition. Ensure it is facing thecorrect way.

Replace the filters in the dooropening by first inserting them at thebottom and then pressing them intoplace at the top.

Lock both dials (you will feel themclick into position).

Cleaning and care

25

Tumble dryer

Disconnect the machine from themains electricity supply.

Do not use solvents, abrasivecleaners, glass cleaners or all-purpose cleaning agents. Thesemight damage plastic surfaces andother components because of thechemicals they contain.

Clean the tumble dryer with a slightlydamp cloth and a mild non-abrasivecleaning agent or a solution ofwashing-up liquid and water.

Clean the seal around the inside ofthe door with a damp cloth.

Dry all parts with a soft cloth.

The drum and other stainless steelparts can be cleaned with a suitableproprietary stainless steel cleanerfollowing the manufacturer'sinstructions. This, however, is notabsolutely necessary.

Cleaning and care

26

Cleaning the condenser unit

Check the condenser unit once ayear and clean it if necessary.Always check the fluff filters and thecondenser unit if the Clean outairways indicator light comes on.

Detergent residue, hair and fine flufffrom the dryer can get through the flufffilters and block the condenser unit.Dust from the room in which the dryeris installed can also get into thecondenser unit and cause a blockage.

Opening the service panel

Use the yellow lever supplied to openthe service panel.

Insert the lever into the middle of thegap in the top (see arrow) and leverthe panel until it opens at the top.

Now remove the panel by pulling itdiagonally upwards. Then place it toone side.

Turn the lever on the inner coverdownwards to the vertical position.

Pull the cover forwards.

Then remove it by pulling it diagonallyupwards.

Turn the lever on the condenser unitto the vertical position so that thehook on the lever is no longer in thegroove at the bottom of thecondenser unit housing.

Cleaning and care

27

Pull the condenser unit out of itshousing by the handle.

Checking the heat exchanger unit

Hold the condenser unit up to thelight as shown.

Check to see if there is any fluff insideit. The arrows in the illustration aboveindicate where to look.

If you cannot see any fluff:

Refit the condenser unit (seefollowing page).

If you can see some fluff:

Clean the condenser unit asdescribed below.

Cleaning the condenser unit

When rinsing the condenser unit, makesure you position it as shown in thenext two illustrations.

Use a shower head or similar to rinsethe unit as shown.

Cleaning and care

28

Then flush the unit through from thefront.

Check the condenser unit again forany visible fluff and, if necessary,flush it through again until it has allgone.

Also make sure that the rubber sealsare clean.

The rubber seals must not be removedand must be free of kinks.

Shake the water off the condenserunit until no more droplets of waterare visible.

Checking and cleaning thecondenser unit housing

Remove any soiling still visible insidethe housing by hand using a dampcloth.

Do not try and access areas youcannot reach by hand!

Cleaning and care

29

Refitting the condenser unit

Push the condenser unit back into thehousing as far as it will go.

Turn the lever down to the horizontalposition, making sure that the hookon the lever clicks into the groove.

When replacing the inner cover aftercleaning, ensure that the rubber sealfits correctly into the groove.Otherwise water may leak from thesystem.

Replace the inner cover making surethe hooks are at the bottom. Hold itat an angle and push down gently.

Press against the cover and lock itwith the lever.

The lever will be in the horizontalposition when locked.

Replace the service panel and pressthe upper edge until it clicks intoposition.

It is important to ensure thatboth the condenser unit and thecover are correctly positioned andlocked, otherwise water may leakfrom the system.

Problem solving guide

30

Problem solving guideWith the help of the following notes minor faults in the performance of theappliance, some of which may result from incorrect operation, can be put rightwithout contacting Miele.

Please note that a call-out charge will be applied to service visits where theproblem could have been rectified as described in these operating instructions.

Repair work to electrical appliances should only be carried out by anauthorised Miele service technician. Repairs and other work by unqualifiedpersons could be dangerous. Miele cannot be held liable for unauthorised work.

Check and fault messages

Problem Possible cause and remedy

The Empty thecontainer indicatorlights up. Theprogramme iscancelled, the buzzersounds.

The condensed water container is full or there is akink in the drain hose. Empty out the condensed water container. Check the drain hose. Open and close the door while the dryer is

switched on. The indicator light will go out.

The programme iscancelled.The buzzer may soundand the Clean outairways or Empty thecontainer indicatorflashes.

There is no obvious cause. Switch the dryer off and then on again. Start a programme.

If the programme is cancelled again and an errormessage appears, there is a fault. Contact Miele.

The programme iscancelled, lights up

This is not a fault. In some programmes, if the drum has beenunderloaded or is empty, the programme will becancelled. This can also happen if the items arealready dry. Open and close the door to resume drying. Use the Warm air programme (timed drying) to dry

individual items.


31


The Start indicator lightflashes slowly and thedisplay is dark

The dryer is in standby. This is a normal function anddoes not indicate a fault. See "Standby" in "Programmable functions".

The Clean out airwaysindicator light comes onat the end of aprogramme

There is a build-up of fluff in the airways. Clean the fluff filters. Clean the condenser unit Open and close the door while the dryer is


The programme iscancelled and the Cleanout airways indicatorlight comes on

An excessive amount of fluff has built up. Clean the fluff filters and condenser unit. Open and close the door while the dryer is


Bars flash in the displayat the end of aprogramme:.........

The programme has finished but the laundry has notyet cooled down. Either remove the laundry and spread it out to cool

down or leave it in the tumble dryer to cool downduring the cooling phase.

lights up The programme selector has been moved. Select the original programme. The time remaining

will appear in the display again.


32

Unsatisfactory drying results


The laundry is notsufficiently dry

The load consisted of different types of fabric. Finish drying using the Warm air timed drying

programme. Select a more suitable programme next time.

Tip: You can alter the drying levels for someprogrammes (see "Programmable functions").

Laundry or feather filledpillows smell afterdrying

The laundry was washed with insufficient detergent.Feathers are a natural product and this is quitenormal. Laundry: use sufficient detergent next time. Pillows: take out of the tumble dryer and aerate. Use a fragrance flacon (available as an optional

accessory) for your favourite fragrance.

Items made of syntheticfibres are charged withstatic electricity afterdrying

Synthetic fibres tend to attract static charge. Static charge can be reduced by adding a fabric

softener to the final rinse in the washingprogramme.

There is a build-up offluff

Fluff is principally the result of friction when garmentsare being worn and to some extent when they arebeing washed. Machine drying hardly causes any fluffto form.Fluff is collected by the fluff filters in the door anddoor opening and can be easily removed. See "Cleaning and care".


33

Other problems


Water leaks from themachine after thecondenser unit hasbeen cleaned

The inner cover of the condenser unit has not beenlocked properly and/or the condenser unit has notbeen positioned correctly.Fluff has collected in the condenser unit housing. Ensure that the condenser unit is positioned

correctly and lock the inner cover. Check the rubber seals. Use a cloth to remove any visible fluff from the

inside of the condenser unit housing.

A programme cannot bestarted

There is no obvious cause. Connect the tumble dryer to the mains electricity

supply. Turn on the tumble dryer. Close the door. Check whether the mains fuse has tripped.

Has there been a power cut? When power isrestored, any previously running programme willrestart automatically.

The interior drumlighting does not comeon

The lighting switches off automatically (to saveenergy). Switch the dryer off and then on again. The lamp needs changing. Change the lamp as

described at the end of this section.

The drying processgoes on too long oreven switches off*

The room in which the tumble dryer is located is toowarm. Ventilate the room thoroughly.

Detergent residues, hair and fine fluff can clog thefilters. Clean the filters and the condenser unit (see

"Cleaning and care").The vents below the door are blocked. Move any objects, such as a laundry basket, away

from the dryer.The fluff filters were still wet when replaced.


34


The drying processgoes on too long oreven switches off*

The fluff filters must be dry.

The laundry is too damp. Spin using a higher spin speed in the washing

machine.The tumble dryer has been overloaded. Do not exceed the maximum load for the

programme selected.Metallic components, e.g. zippers have prevented thedryer from registering the correct moisture level. Open the zippers next time. If the problem recurs, dry these items using the

Warm air timed drying programme.* Before starting another programme: Switch the dryer off and then on again.


35

Changing the lamp

Disconnect the machine from themains electricity supply.

Open the door.

You will find the interior lamp cover atthe top of the drum aperture.

Insert a suitable tool* using lightpressure under the side edge of thelamp cover as illustrated.

* E.g. a wide, flat-bladed screwdriver

Apply a little pressure and whilstdoing so turn your wrist in thedirection of the arrow to open thecover.

The cover will open downwards.

The temperature-resistant lamp shouldonly be ordered from Miele.

The lamp must be replaced withone of the same type andspecification. The lamp specificationand maximum wattage is stated onthe data plate and on the lamp cover.

Turn the lamp anti-clockwise toremove it.

Replace the lamp.

To close the cover, push it upwardsand press it on the left and right untilyou hear it click into position.

Ensure that it is fitted intoposition securely, as any moisturecould cause a short circuit.

After sales service

36

RepairsIn the event of any faults which youcannot remedy yourself, please contactMiele. Please note, however, that a call-out charge will be applied to servicevisits where the problem could havebeen rectified as described in theseoperating instructions.

The contact details for Miele are givenat the back of these operatinginstructions.

When contacting Miele, please quotethe model and serial numbers, both ofwhich are located on the data plate(visible when the door is open).

Optional accessoriesOptional accessories for this tumbledryer are available from Miele (seecontact details at the back of theseinstructions).

You also can order these and manyother useful products via the internet(depending on country).

Drying basket

The drying basket is suspended in thedrum and does not rotate with thedrum. This enables items which mustnot be subjected to mechanical actionto be dried or aired.

Fragrance flacon

A fragrance flacon can be used in yourtumble dryer to add a pleasantfragrance to your laundry.

A fragrance flacon holder is requiredwhich fits into the fluff filter.

WarrantyThe manufacturer's warranty for thisappliance is 2 years.

See the warranty card supplied with thetumble dryer for further details.

Installation and connection

37

Front view

a Mains connection cable

b Condensed water container– empty after every drying cycle

c Control panel

d Door

e Service panel for condenser unit

f Four height adjustable screw feet

g Hose for external drainage ofcondensed water


38

Rear view

a Protruding lid for holding whenmoving the tumble dryer (seearrows)

b Air inlet vent for cooling thecondenser unit

c Mains connection cable

d Hose for external drainage ofcondensed water

e Accessories for external drainage ofcondensed water: hose clip, adapterand hose holder

Installation site

Make sure the dryer door can beopened without hindrance afterinstallation.The appliance must not be installedbehind a lockable door, a slidingdoor or a door with a hinge on theopposite side to that of the tumbledryer, in such a way that a fullopening of the tumble dryer door isrestricted.

Transporting the machine to itsinstallation site

When moving the machine, you canhold it by the lid where it protrudes tothe rear of the dryer. To manoeuvre thedryer out of its packing case to itsinstallation site you will also need tohold it by the front feet.


39

Building under a continuousworktop / in a kitchen run

Building under kits must only beinstalled/dismantled by a suitablyqualified fitter.

– A special building-under conversionkit* with a cover plate to replace theappliance lid is required. It must befitted by a Miele approved technicianto ensure electrical safety. N.B. If youwish to push your appliance under aworktop and there is space to do thiswithout removing the lid, the buildingunder kit is not necessary. Otherwiseit is essential.

– Fitting instructions are supplied withthe conversion kit.

– N.B. When built under, drying timesmay be longer.

– The electrical socket must be locatedin an accessible position near theappliance.

With niche heights of:

– 830-840 mm, longer screw feet* arerequired.

– 870-885 / 915-930 mm, one or tworaising kits* are required.

* accessory available to order

Washer and dryer stack

The tumble dryer can be combined witha Miele washing machine in a washer-dryer stack. The appropriate Mielewasher-dryer "WTV" stacking kit* isrequired.

* accessory available to order

Levelling the dryer

The appliance must stand perfectlylevel on all four feet to ensure safe andproper operation.

The screw feet can be adjusted tocompensate for unevenness in the floor.


40

The gap between the base of thedryer and the floor must not beminimised by a plinth or thick-piledcarpet as this would prevent asufficient intake of cold air.

A build-up of heat can be avoided byadjusting the screw feet so that there isa gap of at least 20 mm between thefloor and the bottom of the dryer.

Do not obstruct the cool airintake at the front with a laundrybasket or other objects.This would hinder a sufficient intakeof cool air for the condenser unit.

Room ventilation

Cool air taken in for the drying processis expelled from the front of the dryerand heats up the air in the room. Ensurethat the room has sufficient ventilation,e.g. by opening a window. Otherwisedrying durations may be longer.

Adequate ventilation has to be providedto avoid the back flow of gases into theroom from appliances burning otherfuels, including open fires.

Before moving the tumble dryeragain (e.g. when moving house)

After each use a small quantity ofcondensed water will collect in the areaof the pump. This water can run out ifthe tumble dryer is tipped up when it isbeing moved. It is a good idea to runthe Warm air programme forapproximately 1 minute before movingthe tumble dryer. Any remainingcondensed water will then be fed intothe condensed water container or outthrough the drain hose.


41

Electrical connectionThis tumble dryer is supplied with amains cable with moulded plug.

The accessibility of the plug must bealways ensured in order to separate thetumble dryer from the mains.

Connection of this appliance shouldcomply with national and local safetyregulations.

Do not connect the appliance via anextension lead. Extension leads do notguarantee the required safety of theappliance (e.g. danger of overheating).

The appliance should be connected uponly by a qualified electrician inaccordance with national and localsafety regulations. For extra safety, it isadvisable to install a residual currentdevice (RCD) with a trip current of 30mA.

The voltage, rated load and plug ratingare given on the data plate. Pleaseensure that these match the householdmains supply.

ImportantThe wires in the mains lead arecoloured in accordance with thefollowing code: Green/yellow = earth Blue = neutralBrown = live As the colours of the wires in the mainslead of this appliance may notcorrespond with the coloured markingsidentifying the terminals in your plug,proceed as follows: The wire which iscoloured green and yellow must beconnected to the terminal in the plugwhich is marked with the letter E or bythe earth symbol or coloured green orgreen and yellow. The wire which iscoloured blue must be connected to theterminal which is marked with the letterN or coloured black. The wire which iscoloured brown must be connected tothe terminal which is marked with theletter A or coloured red.

WARNING THIS APPLIANCE MUST BEEARTHED


42

Externally draining condensedwater

Notes

When drying is in progress,condensed water is pumped into thecondensed water container throughthe drain hose which is located at theback of the dryer.

The condensed water can also bedrained away via the drain hose so thatthe condensed water container doesnot have to be emptied.

Drain hose length: 1.50 mMaximum delivery head: 1.50 mMaximum drain hose length: 4.00 m

The following optional accessoriesare available:

– an extension hose,

– a non-return valve kit for connectionto an external water outlet. The kitincludes an extension hose.

Arranging the drain hose

Do not pull on the drain hoseand do not stretch it or allow it tobecome kinked.This could damage the hose.

There will be a small amount of residualwater left in the drain hose. Have acontainer ready to collect this.

Pull the drain hose off its connection.

Allow any residual water to run intothe container.

Unwind the hose and pull it carefullyout of the holders.


43

Guide the hose to the right or left sideof the dryer, as required.

Leave the hose in the middle holder toprevent it from being kinkedinadvertently.

External drainage via a sink or gully

See "Front view" illustration.

If you want to drain the water offinto a sink or basin, you will need tosecure the hose carefully, e.g. bytying it to a tap, to make sure itcannot slip during use.Otherwise there is a risk ofoverflowing water which could causedamage.

Use the bow-shaped guide to preventthe drain hose from becoming kinked.


44

Installation conditions requiring anon-return valve

There is a risk of backflow intothe dryer if a non-return valve is notfitted.Backflow could damage the dryerand also the room in which it islocated.Certain installation conditions, suchas those described below, requirethe fitting of a non-return valve.

Installation conditions requiring thefitting of a non-return valve:

– Drainage into a sink or floor gullywhere the end of the hose isimmersed in water.

– Connection to a sink drain outlet.

– Connection to a drainage systemalready in use by another appliance,e.g. a dishwasher or washingmachine.

Maximum delivery head with non-returnvalve: 1.00 m

Example: Connection to a sink drainoutlet

The drain hose with non-return valvefitted can be connected directly to asuitable sink drain outlet.

Remove the following from the backof the dryer at the top: Adapter 1 andhose clip 3 behind it.


45

1. Adapter

2. Nut

3. Hose clip

4. End of the hose (secured with thehose holder)

5. Non-return valve

6. Tumble dryer drain hose

Fit the adapter 1 to the sink drainoutlet using the nut 2.The nut is usually fitted with a washerwhich must be removed.

Attach the end of the hose 4 to theadapter 1.

Use the hose holder.

Use a screwdriver to tighten the hoseclip 3 up close to the nut.

Fit the non-return valve 5 to thetumble dryer drain hose 6.

The non-return valve 5 has to befitted so that the arrow points in thedirection of flow (i.e. towards thesink).

Secure the non-return valve usinghose clips.

Consumption data

46

Load1 Final spin

speed in adomesticwashingmachine

Residualmoisture

Energy Duration

kg rpm % kWh min.

Cottons Normal 7.03.5

10001000

6060

4.142.28

10965

Cottons Normal 7.07.07.0

120014001600

535044

3.753.553.15

1009586

Cottons Hand iron 7.07.07.07.0

1000120014001600

60535044

3.102.752.552.20

89797465

Minimum iron Normal 3.5 1200 40 1.40 45

Minimum iron Hand iron 3.5 1200 40 1.20 39

Automatic plus 5.0 900 50 2.70 114

1 Weight of dry laundry

All data was calculated using EN 61121 unless otherwise stated.

Power consumption when switched off:Power consumption when not switched off:

0.10 W3.50 W

Consumption data can vary from the nominal values given above depending on the size of theload, types of textiles, residual moisture levels after spinning and fluctuations in the electricitysupply.

Technical data

47

Height 850 mm

Width 595 mm

Depth 587 mm

Depth with door open 1062 mm

Height for building under 820 mm

Width for building under 600 mm

Depth for building under 600 mm

Suitable for pushing under a worktop Yes

Suitable for stacking Yes

Weight Approx. 51 kg

Drum volume 111 l

Maximum capacity 7.0 kg (weight of dry laundry)

Capacity of condensed water container 4.2 l

Hose length 1.5 m

Max. delivery head 1.5 m

Max. drain hose length 4.00 m

Length of connection cable 2.00 m

Voltage See data plate

Rated load See data plate

Fuse rating See data plate

Lamp wattage See data plate

Test certificates awarded See data plate

48

Programmable functions for changing standard settings

Settings can be used to alter the dryer's electronics to suit differentrequirements. They can be altered at any time.

The tumble dryer's programmable functions are available for use but are notabsolutely necessary for a satisfactory drying result.

Programmable functions

49

Extending the range of thedrying level for the "Cottons"programme

The tumble dryer is designed to dryeffectively using as little energy aspossible. However, if you require thelaundry to be drier or damper, you canreduce or increase the default residualmoisture in this programme.

Exception: The Normal dying levelremains unchanged.

Follow steps (,, ...) toprogramme and store in memory.

Before you begin, ensure thefollowing:

– The tumble dryer is switched off.

– The door is closed.

– The programme selector is pointingto Finish.

Press the Start button and keep itpressed in whilst carrying out steps-.

Switch the tumble dryer on.

Wait until the indicator light for theStart button lights up constantly . . .

. . . and then release the Start button.

The Empty the container indicator lightwill flash once.

The option selected will be displayedby a number which will alternate with.

Laundry will be damper

Factory default setting(The Clean out airways indicator lightwill also flash once)

Laundry will be drier(The Clean out airways indicator lightwill also flash twice)

Pressing the Start button switchesbetween the options.

Switch the tumble dryer off.

The setting you have selected is nowstored in memory. You can change itagain at any time.

To check the setting:

Carry out steps -.

Switch the dryer off after checkingthe indicator lights.


50

Extending the drying level forthe "Minimum iron"programme

The tumble dryer is designed to dryeffectively using as little energy aspossible. However, if you require thelaundry to be drier or damper, you canreduce or increase the default residualmoisture in this programme.










Turn the programme selector toCottons Normal+.

The Empty the container indicator lightwill flash twice.


Laundry will be damper


Laundry will be drier(The Clean out airways indicator lightwill also flash twice)





Carry out steps -.



51

Anti-crease

Helps prevent creasing, if laundry isnot normally removed immediatelyafter the end of a programme. Thedrum rotates at intervals for 2 hoursafter the end of a programme.

Anti-crease

– is activated ex-works. You canshorten the duration of the Anti-crease phase or deactivate it ifwished.

– can be used for all programmes,except Woollens handcare.

– should always be switched on.










Turn the programme selector toCottons Normal.

The Empty the container indicator lightwill flash three times.


Anti-crease action off

Anti-crease 1 h(The Clean out airways indicator lightwill also flash once)

Anti-crease 2 h (factory defaultsetting) (The Clean out airways indicator lightwill also flash twice)





Carry out steps -.



52

Switching the buzzer on/off

A buzzer sounds (at intervals for amaximum of 1 hr) to let you know theprogramme has finished.

The dryer is delivered with the buzzerswitched on, but you can switch it off ifyou wish.

The buzzer will still sound if there is afault, even if it has been switched off.










Turn the programme selector toCottons Low temperature.

The Empty the container indicator lightwill flash four times.


Buzzer off

Buzzer on (factory default setting)(The Clean out airways indicator lightwill also flash once)





Carry out steps -.



53

Altering the standard dryinglevel in the"Automatic plus"programme

The drying level for this programme isset to the standard Normal level. Youhave the option of changing the dryinglevel to Hand iron (damper thanNormal) or to Normal+ (drier thanNormal).










Turn the programme selector toCottons Hand iron.

The Empty the container indicator lightwill flash six times.


Standard setting will be Hand iron


Standard setting will be Normal+(The Clean out airways indicator lightwill also flash twice)





Carry out steps -.



54

Extending the cooling downtime

The cooling down phase which takesplace before the end of a programmecan be lengthened if required. Thismakes the garments easier to handle.










Turn the programme selector toCottons Machine iron.

The Empty the container indicator lightwill flash seven times.


Factory default

Cooling down 5 minutes longer(The Clean out airways indicator lightwill also flash once)

Cooling down 10 minutes longer(The Clean out airways indicator lightwill also flash twice)





Carry out steps -.



55

Standby

To save energy, the display goes outafter 10 minutes and the indicator lightfor the Start button starts flashingslowly.

Reactivate from Standby

Move the programme selector orpress Start. Neither will have anyeffect if a programme is running.

On

Standby is activated and the indicatorlights will go out after 10 minutes:

– if a programme is not selected afterthe dryer has been switched on,

– after a programme has started.

They will, however come on for 10minutes at the end of the programme orthe end of the Anti-crease phase. Thebuzzer (if selected) will sound for 10minutes at the end of the programme.

Not in current programme (factorydefault setting)

As described under "On".However, indicator lights will stay onwhen the programme has started andremain visible during the programme.

Off

Indicator lights will stay on while thedryer is switched on.










Turn the programme selector toGentle smoothing.

The Empty the container indicator lightwill flash eight times.


56


On

Not in current programme (factorydefault setting)(The Clean out airways indicator lightwill also flash once)

Off(The Clean out airways indicator lightwill also flash twice)





Carry out steps -.



57

Clean out airways indicator

Fluff should be removed after drying.The Clean out airways indicator willremind you to clean the filters when acertain amount of fluff has collected inthe filters. You can decide at whatlevel of fluff this reminder should begiven.

You will have an idea of how often thisshould be done after a few dryingprogrammes.

Certain faults can also cause thisindicator light to come on at othertimes.










Turn the programme selectorto Woollens handcare.

The Empty the container indicator lightwill indicate one long flash.


The Clean out airways indicatorlight is deactivated

The Clean out airways indicatorlight only appears when there is aheavy build-up of fluff(The Clean out airways indicator lightwill also flash once)

Factory default setting(The Clean out airways indicator lightwill also flash twice)

The Clean out airways indicatorlight appears when there is only asmall build-up of fluff(The Clean out airways indicator lightwill also flash three times)





Carry out steps -.



58

Adjusting the dryer'selectronics for very soft water

This programmable functionshould only be altered if the water isso soft that it is likely to cause theelectronics which sense residualmoisture in the laundry to give falsereadings.

Important

This programmable function should onlybe set if the water used for washing thelaundry is extremely soft with aconductivity reading (electricalconductivity) less than 150 μS. Contactyour local water authority for theconductivity level of your mains watersupply.

Only activate this programmablefunction if these conditions arepresent. Otherwise drying results willbe unsatisfactory.










Turn the programme selector to Coolair.

The Empty the container indicator lightwill flash on and off slowly once andthen on and off quickly twice.


Factory default

Adjusted for very soft water (withlow conductivity)(The Clean out airways indicator lightwill also flash once)





Carry out steps -.


www.miele.com.au

Miele Experience Centre and Head Office Melbourne:1 Gilbert Park DriveKnoxfield, VIC 3180

Miele Experience Centre South Melbourne:206-210 Coventry StreetSouth Melbourne, VIC 3205

Miele Experience Centre and Office Sydney:3 Skyline PlaceFrenchs Forest, NSW 2086

Miele Experience Centre and Office Brisbane:39 Harvey Street NorthEagle Farm, QLD 4009

Miele Experience Centre and Office Perth:

83-85 Sir Donald Bradman DriveHilton, SA 5033

205-207 Stirling HighwayClaremont, WA 6010

Miele Experience Centre and Office Adelaide:

Miele Australia Pty. Ltd.

Miele New Zealand Limited

Level 2, 10 College HillFreemans Bay, Auckland 1011

Miele Experience CentreAuckland:8 College HillFreemans Bay, Auckland 1011Telephone:0800 464 353 (0800 4 MIELE)www.miele.co.nz

Miele Global HeadquartersGermanyMiele & Cie. KGCarl-Miele-Straße 2933332 GüterslohFederal Republic of Germany

Head Office:

IRD 98 463 631

ACN 005 635 398ABN 96 005 635 398

Miele Experience Centre Gold Coast:131 Ferry RoadSouthport, QLD 4215

M.-Nr. 10 002 130 / 02en-AU, NZ

TDA 150 C

operating instructions condenser tumble dryer...operating instructions condenser tumble dryer to...

Documents