installation procedure: evc-e2 volvo penta ips twin ... · installation procedure: installation...

of 2 /2
Example: Twin installation with (left) and without (right) accessories connected on the AUX bus Installation Procedure: EVC-E2 Volvo Penta IPS Twin Installation Procedure: EVC-E2 Volvo Penta IPS Twin Document number: 47704056 Release date: 05-2013 Buzzer Connection for safety lanyard Rudder angle sender (not used) Fresh water and fuel level senders SUS IMPORTANT! Never cut or modify the Volvo Penta EVC harnesses. For extra power supply, use the Volvo Penta relay for external accessories. Use cable ties. Typical installation / Main station IPS 350/400/450/500/600, IPS 800/950, IPS 1050/1200 1 2 7 4 5 Multisensor SUS CPM ACP 7” display Autopilot 4” display To NMEA2000 backbone Compass (CCU) Joystick Steering wheel Levers Lever connections 5 9 10 12 Multilink hub Termination plug 12 10 Termination plug 1 20 7 7 7 25 7 AUX bus termination D11 D11 Flybridge Joystick Steering wheel Multilink hub Buzzer Multifunction panel (Start/Stop panel) Dynamic Positioning System interface Dynamic Positioning System antenna 7” display Levers Lever connections 10 11 11 18 9 Autopilot 4” display To NMEA2000 backbone 10 10 20 20 Display options Twin Female terminator Male terminator Chartplotter EVC Autopilot Compass (CCU) EVC Autopilot Battery 12 VDC T-connector Backbone ex- tension cable Fuse Power cable 23 20 20 20 20 Use AUX relay 24 20 22 24 e-Key panel Engine connections IPS 350/400/450/500/600 IPS 1050/1200 AUX BUS AUX BUS AUX BUS AUX BUS AUX BUS AUX BUS SENDERS DATALINK DATALINK DATALINK SENDERS SENDERS A C ENGINE CONN. DIAGNOS Connection locations B A C Docking station Joystick Stand- alone HCU Multifunction panel (Docking station panel) Stand-alone HCU connections Buzzer 11 11 10 Interceptor Control Unit (ICU) Color coded cables Interceptor Servo unit Interceptor Servo unit Connecting multiple Multilink hubs B IPS 800/950 31 31 To next station To next station IMPORTANT! This end of Y-connector must be connected directly, without extension, to levers/HCU. Helm station Helm station 8 8 7 8 8 Engine Engine 8 11 11 11 7 11 Multiple helm stations Y-connector Buzzer Connection for safety lanyard Analog Key Analog key interface (optional) 7” display NMEA2000 backbone 7 7 MAX MIN MIN 4” display 2,5” display MAX MIN MAX Correct! Termination in the beginning and at the end of the AUX bus Termination plug 5 7 7 7 7 2 7 7 10 33 There is no need of termination plugs if nothing is connected on the AUX bus. IMPORTANT! Maximum cable length between Multil- ink hub and unit (display etc.) is 3 m (10 ft). Maximum total cable length on Multilink is 20 m (66 ft). 7 7

Author: vokhanh

Post on 22-Apr-2018

503 views

Category:

Documents


16 download

Embed Size (px)

TRANSCRIPT

  • Example: Twin installation with (left) and without (right) accessories connected on the AUX bus

    Installation Procedure: EVC-E2 Volvo Penta IPS TwinInstallation Procedure: EVC-E2 Volvo Penta IPS Twin

    Document number: 47704056

    Release date: 05-2013

    Buzzer

    Connection for safety lanyard

    Rudder angle sender (not used)

    Fresh water and fuel level senders

    SUS

    IMPORTANT! Never cut or modify the Volvo Penta EVC harnesses. For extra power supply, use the Volvo Penta relay for external accessories. Use cable ties.

    Typical installation / Main station

    IPS 350/400/450/500/600, IPS 800/950, IPS 1050/1200

    1

    2

    7

    4

    5

    Multisensor

    SUS

    CPM

    ACP

    7 display

    Autopilot 4 display

    To NMEA2000 backbone

    Compass (CCU)

    Joystick

    Steering wheelLevers

    Lever connections

    5

    910

    12

    Multilink hub

    Termination plug

    12

    10

    Termination plug

    1

    20

    7

    7

    7

    25

    7

    AUX bus termination

    D11

    D11

    Flybridge

    Joystick

    Steering wheel Multilink hub

    Buzzer

    Multifunction panel(Start/Stop panel)

    Dynamic Positioning System interface

    Dynamic Positioning System antenna

    7 display

    Levers

    Lever connections

    10

    11 11

    18

    9

    Autopilot 4 display

    To NMEA2000 backbone

    10

    10

    20

    20

    Display options Twin

    Female terminator

    Male terminator

    ChartplotterEVC AutopilotCompass (CCU)EVC Autopilot

    Battery 12 VDC

    T-connectorBackbone ex-tension cable

    Fuse Power cable

    23 20

    20 2020Use AUX relay

    24 20 22 24

    e-Key panelEngine connections

    IPS 350/400/450/500/600

    IPS 1050/1200

    AU

    X BU

    SA

    UX B

    US

    AU

    X BU

    S

    AUX BUS

    AUX BUS

    AU

    X BU

    S

    SEN

    DER

    S

    DATA

    LINK

    DATALINK

    DATA

    LINK

    SENDERS

    SEN

    DER

    S

    A

    C

    ENGINE CONN.

    DIAGNOS

    Connection locations

    BA C

    Docking station

    Joystick

    Stand-alone HCU

    Multifunction panel(Docking station panel)

    Stand-alone HCU connections

    Buzzer

    11 11

    10

    Interceptor Control Unit (ICU)

    Color coded cables Interceptor Servo unitInterceptor Servo unit

    Connecting multiple Multilink hubs

    B

    IPS 800/950

    3131

    To next station To next station

    IMPORTANT! This end of Y-connector must be connected directly, without extension, to levers/HCU.

    Helm station

    Helm station

    8

    8

    7

    8

    8

    Engine Engine

    8

    11

    11 11

    7

    11

    Multiple helm stationsY-connector

    Buzzer

    Connection for safety lanyard

    Analog Key

    Analog key interface (optional)

    7 display

    NMEA2000 backbone

    77

    MAXMIN

    MIN

    4 display

    2,5 display

    MAX

    MIN

    MAX

    Correct!Termination in the beginning and at the end of the AUX bus

    Termination plug

    5

    7 7 7 7

    2

    7

    7

    10

    33

    There is no need of termination plugs if nothing is connected on the AUX bus.

    IMPORTANT! Maximum cable length between Multil-ink hub and unit (display etc.) is 3 m (10 ft).Maximum total cable length on Multilink is 20 m (66 ft).

    7

    7

  • e-KeyPart no. 21758351

    Compass (CCU)Part no. 21812209

    Steering wheel non tilt adjuster

    Steering

    JoystickIncl. cables 1.5 m (5 ft.)

    Steering wheel tilt adjuster Steering wheel hubIncl. cables 2.5 m (8 ft.)

    Interceptor Control Module (ICM)Manual: 21888398 Auto/Manual: 21875631

    47

    70

    40

    56

    05

    -20

    13

    Components and CablesControls

    Components

    Stand-alone HCU

    Part no. 21856286

    LeversBuilt-in HCUsPart no. 21856280

    LeversPalm Beach In combination with A-CANPart no. 3888616

    e-Key panelIgnition, start/stop and locking/unlocking the boat system.Kit no. 21836809

    Multilink hub6 cable socketsKit no. 21469055

    Autopilot interface NMEA 0183 interface NMEA 2000 interface

    Dynamic Positioning System interface

    7 display power supply for 12 V systems

    MultisensorTransom mountedKit no. 3587055

    A-CANAnalog lever interfaceKit no. 21460908

    MultisensorHull mounted

    SenderFuel level sender 3180 ohm

    SenderWater level sender 3180 ohm

    Clear Wake Exhaust System Only for IPS800-1200Kit no. 21499486

    Dynamic Positioning System antennaKit no. 22050476

    ACP KitTransom unit Included in ACP-kit Part no. 22037078

    ACP KitCPM unit Included in ACP-kit, Active Corrosion Protection for fiber-glass hulls.Part no. 40005219

    19. Display cable, 5/6-pinFeet Meter Part no.5 1.5 21640400 Incl. in display kit

    20. NMEA 2000 Extension cableFeet Meter Part no.1 0.3 21812185 6.6 2 21812194** 13 4 21867150 19 6 21867151 33 10 21867152

    24. NMEA2000 Termination plugs Type Part no.Male 21812196** Female 21812203**

    23. NMEA2000 Powercable Feet Meter Part no.6.6 2 21812205**

    22. NMEA2000 T-connectorPart no. 21812195**

    Cables

    7. Standard EVC bus cable, 6-pin* Feet Meter Part no.5 1.5 21865234 16 5.0 874789 23 7.0 889550 30 9.0 889551 36 11.0 889552 42 13.0 888013*) One cable per engine has to be ordered.

    8. Y-connector, 6-pinFeet Meter Part no.1.6 0.5 3588972

    10. Multilink cable, 6-pinFeet Meter Part no.5 1.5 3886666

    11. Extension cable, 6-pinFeet Meter Part no.5 1.5 3889410 10 3.0 3842733 16 5.0 3842734 23 7.0 3842735 30 9.0 3842736 36 11.0 3842737 66 20.0 21172469 131 40.0 21172470

    16. Extension cable, 3-pin EasyLinkFeet Meter Part no.3 1.0 874759 10 3.0 3807043

    12. Sender cable, 6-pinFeet Meter Part no.16 5.3 3807229

    17. Steering adapter, 12/6-pinFeet Meter Part no.0.6 0.2 21421945

    15. Extension cable, 6-pin Joystick/Steering wheel hubFeet Meter Part no.5 1.5 21480272

    13. Aux. relay cable, 6-pinFeet Meter Part no. 3.3 1.0 21427463Kit with cable & relay 12V: 21475508 24V: 21475509

    6. Y-split steering, 6-pinFeet Meter Part no.1.3 0.4 21421941

    9. 7 display cable, 6-pinFeet Meter Part no.5.5 1.7 21514712**) Incl. in display kit

    14. Extension cable, 6-pin Feet Meter Part no.23 7.0 21166002 30 9.0 21166003 43 13 .0 21166004

    18. Y-split multilink, 6-pinFeet Meter Part no.1.6 0.5 3588206

    1 b. Wiring harness

    IPS 800-950Feet Meter Part no.4.3 1.3 21851490 5.6 1.7 21851491 7.2 2.2 21851492 8.5 2.6 21851493 10.2 3.1 21851494 11.5 3.5 21851495 18 5.5 21851496

    1c. Wiring harness

    IPS 1050-1200Feet Meter Part no.4.3 1.3 21759842 5.6 1.7 21755840 7.2 2.2 21758217 8.5 2.6 21758219 10.2 3.1 21758220 11.5 3.5 21758221 18 5.5 21858754

    2. Multisensor Y-split*Feet Meter Part no.1.9 0.6 21825662*) Wiring harness AUX-bus.

    4. CPM Y-split*Feet Meter Part no.1.9 0.6 21825665*) Wiring harness AUX-bus.

    5. Termination plugPart no.21825714

    2.5 displayNot in combination with 4 or 7 display.Kit no. 21846916

    7 display Color displayAutopilot 4 displayColor displayPart no. 21812273

    4 display Color display Not in combination with 2.5 or 7 display.Kit no. 22080265

    Not in combination with 2.5 or 4 display.Kit no. 22080260

    1 a. Wiring harness

    IPS 350-600Feet Meter Part no.1.9 0.6 21865860 6.2 1.9 21865861e-Key (standard)

    Locking/unlocking the boat system

    e-Key System

    25. e-Key harness with Safety lanyard Feet Meter Type Part no.5 1.5 Single panel 21693202 5 1.5 Twin panel 21693206

    26. e-Key harness without Safety lanyardFeet Meter Type Part no.5 1.5 Single panel 21693204 5 1.5 Twin panel 21693208

    Multifunction panelFunction configured at startup.Kit no. 21846926

    Kit no. 3587054Part no. 21231837 Included in Dynamic Positioning System antenna kit.

    Part no. 21379779

    Part no.

    Part no. 3809098Part no. 21575479

    Kit no. 21230216

    Part no. 21469560Part no. 21581323Part no. 21846873Kit no. 21836809

    **) Incl. in Autopilot kit:

    31. Interceptor servo cableFeet Meter Part no.13 4 21875632 Incl. in Interceptor kit:

    Interceptor system Interceptor and servo unit

    Kit IS 600 : Part no. 21875622 Kit IS 750 : Part no. 21875623 Kit IS 900 : Part no. 21875624 Kit IS 1050 : Part no. 21875625

    32. e-Key extension cable, 12-pinFeet Meter Part no.4.7 1.44 22067251

    0183: 38075872000: 3889758

    33. Stbd. AKI, 4/8-pin Feet Meter Part no.0.6 0,2 21421946

    LeversBuilt-in HCUs with ISPart no. 21897586